Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
board. This is an SoM with STM32MP15xx and an evaluation kit. The
baseboard provides Ethernet, UART, USB, CAN and optional display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
It's a very rare if at all existing occasion when ARC CPU template
is used as is w/o any changes - in the end it's a beauty and competitive
advantage of ARC cores to be tailored for a particular use-case - and
so it doesn't make a lot of sense to offer template-based "-mcpu" selection.
Given for each and every platform we end-up adding quite a few more flags
it's logical to move "-mcpu" selection to platform's definition as well
which we exactly do here.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Given now nsim_hs38 configuration is usable on QEMU and in QEMU
we have Virtio working perfectly fine the next logical step
is to add support of supported & known to work net & bkl to this
config.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We don't have yet any brc700 or big-enadian platforms with networking
support to run this particular configuration.
Whenever QEMU for ARC supports arc700 or big-endian targets we may revisit
this one.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Since v2019.06 DesingWare nSIM supports DesignWare UART simulation
and so we may switch from pretty unusual ARC UART to much more standard
DesignWare UART (which in case of U-Boot is just an ordinary 16650 UART).
This among other things makes built dinaries compatible with our other
platforms to name a few: FPGA-based HAPS boards, QEMU and even ZeBU.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
- Move P2SB from Apollo Lake to a more generic location
- Add a function to find a device by drvdata in DM core
- Enhancement of DM IRQ uclass driver
- Add a clock driver for Intel devices
- Add support for ACPI general-purpose events
- Add a TPM driver for H1/Cr50
- Enable TPM on Google Chromebook Coral
Drop PPD_UART_PAD_CTRL since it matches defaults.
Enable DM serial and MXC uart.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Add backlight and panel devicetree definitions
Use UCLASS_PANEL to enable backlight via display enable handler
Remove old explicit gpio code for handling backlight
Use cls command to initiate display in HW agnostic manner
Enable DM regulator and pwm
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Enable DM_VIDEO for mx53ppd.
Enable DM_REGULATOR_FIXED and DM_PWM for the backlight.
Remove unused MX53PPD_LCD_POWER.
Remove old (incorrect) setup_iomux_lcd.
Enable backlight via display enable handler.
Use cls command to initiate display in HW agnostic manner.
Modify `failbootcmd' to use lcdputs.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Add bootcount node, linking to i2c eeprom "bootcount" partitions for
storage.
Enable i2c eeprom bootcount backend storage.
Enable bootcount command and use it for failbootcmd.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Add bootcount node, linking to i2c eeprom "bootcount" partitions for
storage.
Enable i2c eeprom bootcount backend storage.
Enable bootcount command and use it for failbootcmd.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Remove old (pre-DM) i2c setup code.
Enable DM i2c.
Convert common code to use DM rtc.
Convert common code to read VPD from eeprom partition.
Convert the generic i2c PMIC init code to use the new da9063 driver.
mx53ppd only:
Correct RTC compatible in device tree.
Enable MXC DM i2c driver.
Define CONFIG_SYS_MALLOC_F_LEN so that DM is available in pre-reloc.
Make GPIO banks available during preloc, since initialisation is done
in board_early_init_f().
Add gpio_request() calls to satisfy the DM_GPIO compatibility API.
Remove unused power configuration.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Convert imx6sabresd PCI to driver model to fix the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_PCI Please update
the board to use CONFIG_DM_PCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
After the conversion the following commands were used for testing:
=> pci enum
PCI: Failed autoconfig bar 10
PCI: Failed autoconfig bar 10
=> pci 1
Scanning PCI devices on bus 1
BusDevFun VendorId DeviceId Device Class Sub-Class
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable DM thermal driver and iMX thermal driver to get accurate
CPU frequency reporting in the boot log.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Just move the defconfig entries which are required into the Novena
entry in arch Kconfig, no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Redundant envs help with assuring better reliability for the system as they
prevent from the situation when envs are stored only in a single place.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Both CMD_MX_CYCLIC and MX_CYCLIC are in use and defined in Kconfig,
but only the non-CMD version currently does anything. This changes all
usages to prefer the CMD_MX_CYCLIC option (since it's only affecting
addition of the commands), and switches defconfigs using the non-CMD
version to use the CMD version.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently there are two targets for the i.MX6SX SabreSD board:
mx6sxsabresd_defconfig and mx6sxsabresd_spl_defconfig.
This brings additional maintainance effort without a clear
advantage.
Keep only the mx6sxsabresd_defconfig one and remove
mx6sxsabresd_spl_defconfig to keep it simpler.
Also remove the SPL related code from the board file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
The CONFIG_DM_74X164 symbols should be moved to the defconfig file,
as indicated in the comments.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad
2GB WB IT V1.0A module. They are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports booting from the on-module eMMC only, SDP support is disabled
for now due to missing i.MX 8M Mini USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100)
Normal Boot
Trying to boot from MMC1
NOTICE: Configuring TZASC380
NOTICE: RDC off
NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty
NOTICE: BL31: Built : 01:11:41, Jan 25 2020
NOTICE: sip svc init
U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100)
CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz
Reset cause: POR
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial#
06535149
Net: eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
Verdin iMX8MM #
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This partially reverts changes by commit 2cc393f32f
("video: make BPP and ANSI configs optional") since it
caused issues with other boards (missing LCD console
output on pinebook, x86 platform or sandbox). Enable
all disabled options again and opt out of not supported
color depth in board defconfigs.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Vagrant Cascadian <vagrant@debian.org>
- add dfu support to dwc2 for bcm2835
- enable DFU for RPi4
- Fix RPi4 memory map to include the genet device
- add driver for the genet ethernet device
- enable network support in RPi4 config
-----BEGIN PGP SIGNATURE-----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=Sv9b
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2020.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-raspberrypi
- DFU support file operations lager then the default max size
- add dfu support to dwc2 for bcm2835
- enable DFU for RPi4
- Fix RPi4 memory map to include the genet device
- add driver for the genet ethernet device
- enable network support in RPi4 config
Convert the designware watchdog timer driver to DM and add DT probing
support. Perform minor coding style clean up, like drop superfluous
braces. These ought to be no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Philipp Tomisch <philipp.tomisch@theobroma-systems.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # roc-rk3399-pc
- Various minor fixes for x86
- Switch to ACPI mode on Intel edison
- Support run-time configuration for NS16550 driver
- Update coreboot and slimbootloader serial drivers to use NS16550
run-time configuration
- ICH SPI driver fixes to hardware sequencing erase case
- Move ITSS from Apollo Lake to a more generic location
- Intel GPIO driver bug fixes
- Move to vs2017-win2016 platform build host for Azure pipelines
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1021A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1012A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable FSPI controller support. So, flash environment can now be used
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable DFU, Fastboot and USB mass storage gadget related configs
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Enable USB Gadget for R5 SPL, A72 SPL and A72 U-Boot to support DFU boot
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Increase R5 SPL early malloc memory pool by ~7K to accommodate SPL USB
DFU boot requirements
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The current environment offset overlaps with the sysfw area and whenever
environment is saved in the redundant slot, it overwrites sysfw.itb. Fix
the offset to prevent this.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Unit test for 'abootimg' command. Right now it covers dtb/dtbo
functionality in Android Boot Image v2, which was added recently.
Running test:
$ ./test/py/test.py --bd sandbox --build -k test_abootimg
shows that 1/1 tests passes successfully.
Signed-off-by: Sam Protsenko <joe.skb7@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
SFI is quite poor and useless resource provider. Moreover it makes hard
to develop and extend functionality in the Linux kernel.
Enable a necessary minimum to use ACPI on Intel Edison.
Linux kernel have been prepared for this change since v5.4, where the last
crucial driver, i.e. for Basin Cove PMIC, has been submitted.
Note, that stock image won't suffer by this change since it doesn't have
ACPI enabled on the kernel level.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable command line editing, because it is extremely convenient.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Migrate CONFIG_DESIGNWARE_WATCHDOG to Kconfig and update the headers
accordingly, no functional change. The S10 enables the WDT only in
SPL, but does not enable it in U-Boot itself, hence disable it in
the config again.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Philipp Tomisch <philipp.tomisch@theobroma-systems.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
This enables readning the cpuid from e-fuse, and deriving a static
MAC address from it.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip use CONFIG_SPL_OPTEE for OPTEE support, which is load and run
before U-Boot, but not use CONFIG_OPTEE which is after U-Boot.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
All rockchip platforms support TPL or SPL-based bootloader
in mainline with U-Boot proper as final stage. For each
stage we need to burn the image on to flash with respective
offsets.
This patch creates a single boot image component using
- binman, for arm32 rockchip platforms
- pad_cat, for arm64 rockchip platforms.
This would help users to get rid of burning different
boot stage images.
The new image called 'u-boot-rockchip.bin'
which can burn into flash like:
₹ sudo dd if=u-boot-rockchip.bin of=/dev/sda seek=64
This would support all rockchip platforms, except rk3128
since it doesn't support for SPL yet.
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RK3288, RK3399 are now support cpu-info, so enable
DISPLAY_CPUINFO by default.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable winbond SPI flash for ROC-PC-RK3399 board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable winbond SPI flash for ROC-PC-RK3399 board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Raspberry Pi 4 SoC features an integrated Gigabit Ethernet
controller, connected as a platform device.
Enable the new driver in the three applicable defconfigs, to allow
TFTP booting on the board.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
[Andre: Add joined and 32-bit configs]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Enable support for DFU over USB. This requires to enable USB gadget,
DWC2 UDC OTG driver and DFU command. DFU entities are defined for the
following firmware objects: u-boot.bin, uboot.env, config.txt, and
zImage/Image.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
XOM pins provide information for iROM bootloader about the boot device.
Those pins are mapped to lower bits of OP_MODE register (0x10000008),
which is common for all Exynos SoC variants. Set the default MMC device id
to reflect the boot device selected by XOM[7:5] pins (2 for the SD or 0 for
the eMMC).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Orange Pi Win has gigabit ethernet port, but default U-Boot
configuration for that board enabled ethernet driver but
didn't enable realtek phy.
Fix that.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This patch includes the following:
1. Add fastboot command to erase the whole EMMC_USER
2. Add fastboot command to flash image at EMMC_BOOT1
3. Add fastboot command to erase the whole EMMC_BOOT1
4. Enale CONFIG_FASTBOOT_MMC_BOOT1_SUPPORT for mt8518
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
The Libre Computer ALL-H5-CC board is an upgraded version of the
ALL-H3-CC. Changes include:
- Gigabit Ethernet via external RTL8211E Ethernet PHY
- 16 MiB SPI NOR flash memory
- PoE tap header
- Line out jack removed
Only H5 variant test samples were made available, and the vendor is not
certain whether other SoC variants would be made or not. Furthermore the
board is a minor upgrade compared to the ALL-H3-CC. Thus the device tree
simply includes the one for the ALL-H3-CC, and adds the changes on top.
The device tree was synced over from the Linux kernel, along with other
H3/H5 changes, in a previous patch. Thus only the defconfig and an entry
to the MAINTAINERS file is added.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[jagan: drop CONFIG_SYS_SPI_U_BOOT_OFFS]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The Libre Computer ALL-H3-IT board is a small single board computer that
is roughly the same size as the Raspberry Pi Zero, or around 20% smaller
than a credit card.
The board features:
- H2, H3, or H5 SoC from Allwinner
- 2 DDR3 DRAM chips
- Realtek RTL8821CU based WiFi module
- 128 Mbit SPI-NOR flash
- micro-SD card slot
- micro HDMI video output
- FPC connector for camera sensor module
- generic Raspberri-Pi style 40 pin GPIO header
- additional pin headers for extra USB host ports, ananlog audio and
IR receiver
Only H5 variant test samples were made available, but the vendor does
have plans to include at least an H3 variant. Thus the device tree is
split much like the ALL-H3-CC, with a common dtsi file for the board
design, and separate dts files including the common board file and the
SoC dtsi file. The other variants will be added as they are made
available.
The device tree was synced over from the Linux kernel, along with other
H3/H5 changes, in a previous patch. Thus only the defconfig and an entry
to the MAINTAINERS file is added.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[jagan: drop CONFIG_SYS_SPI_U_BOOT_OFFS]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
For Allwinner SoCs the CONFIG_SYS_SPI_U_BOOT_OFFS value is not really a
board choice: The boot ROM only loads the SPL from offset 0 of the SPI
NOR flash, and loads at most 32KB. This is a similar situation as on MMC,
so consequently we create our "joint" image (SPL + U-Boot proper) with
that 32KB offset during the build.
So define the value of this symbol to be 32KB by default for every
Allwinner SoC. This removes the definition of this symbol from the
_defconfig files, and avoids every board to define this over and over
again.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Now that the USB PHY on the Allwinner R40 SoC is supported, enable USB
support for the two R40 boards U-Boot supports.
For this we need to add the GPIO pin that powers the USB port(s), also
enable the usual suspects (OHCI/EHCI support).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The M2 Berry features the normal Gigabit PHY connected to the SoC's MAC,
so enable the sun8i-emac driver to support Ethernet on the board.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
LS1028A QDS boards have a MDIO MUX and they require the driver for it for
PHYs to work.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
setexpr command is used while running secure boot
(chain of trust with confidentiality) feature.
Enable CONFIG_CMD_SETEXPR to enable setexpr command.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently LS1028A board code uses arch_misc_init to set up the board mux
on QDS. Move this code to misc_init_r. This is consistent with LS gen 2
and T series SoCs/boards.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently LX2 board code uses arch_misc_init to set up the board mux on
RDB and QDS. Move this code to misc_init_r. This is consistent with LS
gen 2 and T series SoCs/boards.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
lx2160a rev1 and rev2 SoC has different pcie controller.
The pcie controller device tree node fields "compatible"
and registers names needs to be updated accordingly.
Enable CONFIG_OF_BOARD_FIXUP to apply board_fix_fdt
which updates the "compatible" and registers names.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add Common device tree fixup for NXP SoCs. Based on
SoC and revision call pcie_layerscape or pcie_layerscape_gen4
fixup.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable RTL8152, AX88179 and AX8817X USB network cards support
for ls1012afwry
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable RTL8152, AX88179 and AX8817X USB network cards support
for ls1088ardb
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable RTL8152, AX88179 and AX8817X USB network cards support
for ls1046afrwy
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This target is out of maintenance and can be removed.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This target is out of maintenance and can be removed.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This board is similar to SUV31, but the FPGA is reset concept is quite
different.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This add the initial support of the broadcom reference
board bcm968360bg with a bcm68360 SoC.
This board has 512 MB of RAM, 256 MB of flash (nand),
2 USB port, 1 UART, and 4 ethernet ports.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
The ST-Ericsson U8500 SoC has been used in mass-production for
some Android smartphones released around 2012.
In particular, Samsung has released more than 5 different
smartphones based on U8500, e.g.
- Samsung Galaxy S III mini (GT-I8190) "golden"
- Samsung Galaxy S Advance (GT-I9070) "janice"
- Samsung Galaxy Xcover 2 (GT-S7710) "skomer"
and a few others.
Mainline Linux has great support for the Ux500 SoC, so these
smartphones can also run Linux mainline quite well.
Unfortunately, the original Samsung bootloader used on these devices
has limitations that prevent booting Linux mainline directly.
It keeps the L2 cache enabled, which causes Linux to crash very early,
shortly after decompressing the kernel.
Using U-Boot allows to circumvent these limitations. We can let the
Samsung bootloader chain-load U-Boot and U-Boot locks the L2 cache
before booting into Linux. U-Boot has several other advantages
- it supports device-trees directly and we are no longer limited to
flashing Android boot images through Samsung's proprietary download
mode.
The Samsung "stemmy" board covers all Samsung devices based on U8500.
Add minimal support for "stemmy". For now only UART is supported but
this will be extended later.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
K3 J721E:
* DMA support.
* MMC and ADMA support.
* EEPROM support.
* J721e High Security EVM support.
* USB DT nodes
K3 AM654:
* Fixed boot due to pmic probe error.
* USB support and DT nodes.
* ADMA support
DRA7xx/AM57xx:
* BBAI board support
* Clean up of net platform code under board/ti
AM33/AM43/Davinci:
* Reduce SPL size for omap3 boards.
* SPL DT support for da850-lcdk
* PLL divider fix for AM335x
Currently the following build warning is seen:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
===================================================
Since the mx7ulp-evk board does not have networking support, explicitly
disable networking.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Add iMX6ULL VisionSOM SoM and VisionCB-RT-STD evaluation board support.
The SoM has an iMX6ULL, 512 MiB of DRAM and microSD slot. The carrier
board has Ethernet, USB host port, USB OTG port.
Signed-off-by: Arkadiusz Karas <arkadiusz.karas@somlabs.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Enable USB keyboard to be used as input device at U-Boot prompt. Both
serial and USB keyboard will be active inputs simultaneously.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Enable configs related to USB Host mode, Peripheral mode and DFU.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Currently the DM37 and OMAP35 boards do not boot due to SPL
bring too large.
SPL doesn't need GPIO, I2C nor MMC sector access since it uses
a FAT file system.
This patch unifies all these boards to remove these unused features
from their defconfigs
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add new defconfig files for the J721e High Security EVM.
These defconfigs are the same as for the non-secure part, except for:
CONFIG_TI_SECURE_DEVICE option set to 'y'
CONFIG_FIT_IMAGE_POST_PROCESS option set to 'y'
CONFIG_SPL_FIT_IMAGE_POST_PROCESS option set to 'y'
CONFIG_BOOTCOMMAND uses FIT images for booting
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Sync new additions to non-HS defconfig with HS defconfig.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Sync new additions to non-HS defconfig with HS defconfig.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Adding the configurations to the evm_defconfig file
Signed-off-by: Jason Kridner <jdk@ti.com>
Signed-off-by: Caleb Robey <c-robey@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Split the board and SOC support for STM32MP15x family and
prepare the introduction of new boards with STM32MP15x.
This path define the 2 configurations:
- STM32MP15x: STM32MP15x soc support (new)
- TARGET_ST_STM32MP15x: STMicroelectronics board support (choice)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move CONFIG_ENV_SECT_SIZE and CONFIG_ENV_OFFSET in stm32mp15_*_defconfig
for ST board with NOR support (STM32MP15xx-EV1 boards)
- CONFIG_SECT_SIZE values = the max supported NOR erase size (256KB)
- CONFIG_ENV_OFFSET = offset for NOR (ENV_IS_IN_SPI_FLASH)
This Patch prepares the U-Boot support of boards with STM32MP15x SOC
not provided by STMicroelectronics.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Currently the following build warning is seen:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
===================================================
Since the mx7ulp-evk board does not have networking support, explicitly
disable networking.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
- Clearfog: Fix SD booting (Baruch)
- Misc updates to MMC handling in SPL to support booting from
main data partition (vs hardware boot partition) on MVEBU (Baruch)
This patch add CONFIG_TARGET_MT7623 into mt7623n_bpir2_defconfig
to fix the mt7623 compile error after building others mediatek target
platform
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
This adds a general board file based on MT7622 SoCs from MediaTek.
This commit is adding the basic boot support for the MT7622 rfb.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
This adds a general board file based on MT8512 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
This commit is adding the basic boot support for the MT8512 eMMC board.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
Armada 38x ROM skips the first SD card offset when loading SPL. This
affects the location of the main U-Boot image. SPL MMC code now supports
U-Boot image offset based on run-time detection of the boot partition.
Use this feature to make the same generated image support both SD card
and eMMC boot partition.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
SPL needs DM GPIO to read the SD card-detect signal. This complements
the fix in commit 70bae02f71 ("arm: mvebu: clearfog: fix boot from SD
card").
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Rename CONFIG_SPL_DMA_SUPPORT to CONFIG_SPL_DMA. This allows to use
macros such as CONFIG_IS_ENABLED() that allow conditional compilation of
code for SPL and U-Boot.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For DM_ETH support , it's require to disable this config.
When this config is enable, This generate a error with spl in linker script
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Some i.MX8QXP MEK boards do not have MAC address stored
and hang during eth driver probe:
Error: ethernet@5b040000 address not set.
(Board hangs)
To fix this problem select CONFIG_NET_RANDOM_ETHADDR so that
a valid MAC address can be used in such case.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Qemu v4.2.0 maps bootmode registers to address space which was the reason
why board_late_init() was disabled and accesses were failing.
With new Qemu board_late_init() can be called without any issue.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
zcu1285 is the same as zcu1275 but it is using Avnet FMC
http://www.ultrazed.org/product/network-fmc-module
Unfortunately not everything is connected now that's why this is only
describing system which Xilinx is using.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Decrease amount of the similar defconfigs and use generic one instead.
The change was declared by commit 4b37c13dc3
("arm64: zynqmp: Introduce virtual defconfig") and this patch removes
configs for the most of the boards.
Utra96/zcu100/zcu102/zcu102 and ZynqMP based System controllers *a2197*.
have been also boot tested to make sure that funcionality
remains the same.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
These options are taken from zcu102/104 platforms. Also use OF_SEPARATE
instead of OF_BOARD. Maybe at some point this option will be taken back but
as of now board detection is not ready.
export DEVICE_TREE="zynqmp-zcu102-revA"
make xilinx_zynqmp_virt_defconfig
make -j
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In past SPL_ZYNQMP_TWO_SDHCI symbol was introduced to handle boards with
two sdhci controllers. The problem was that U-Boot is registering
controllers based on aliases in DT but bootmode targets specific controller
ID. That's why on boards with one "second" sdhci controller bootmode was
pointing to second controller(MMC2) but alias was setup to mmc0 (the first
controller). And SPL requires to point to mmc0 in this case.
Long time ago commit f101e4bd37
("spl: add support for alternative boot device") added support for handling
multiple bootmodes in SPL. Use this functionality and setup second sdhci
controller as backup boot device.
Below is table with behavior:
HW/bootmode bootorder
sd0/sd0 mmc0/mmc1 (mmc1 never called)
sd1/sd1 mmc1/mmc0 (mmc0 fails and mmc1 is called)
sd0+sd1/sd0 mmc0/mmc1 (mmc1 never called)
sd0+sd1/sd1 mmc1/mmc0 (mmc0 never called)
All other bootmodes are not affected but order can be extended to cover
advance boot flows.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
These commands are useful in connection to usb and other devices that's why
enable it by default.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Rename the existing 'dtimg' command to 'adtimg', in order to:
- Suggest the Android origins and scope
- Be consistent with the upcoming 'abootimg' command (naming
suggested by Simon [*])
The change in _not_ backward compatible, but its benefits outweigh its
downsides, given that we don't expect active users of 'dtimg' today.
Perform the rename in several steps:
1. Rename *.c file and Kconfig symbol. This should allow
'git log --follow' to properly track the history of 'adtimg.c'
2. 's/dtimg/adtimg/g' in the internal namespace of 'adtimg.c'
ELF comparison [**] before and after shows no functional change.
[*] https://patchwork.ozlabs.org/patch/1182212/#2291600
[**] diff -u <(objdump -d cmd/dtimg.o) <(objdump -d cmd/adtimg.o)
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Glass<sjg@chromium.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
The M25P80 and M25P32 SPI flashes from Numonix/Micron
will be replaced by Marconix MX25L80 and MX25L32 flashes.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This target is out of maintenance and can be removed.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch only fixes a typo.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This pull request provides:
* support for FIT images for UEFI binaries
* drivers for hardware random number generators
* an implementation of the EFI_RNG_PROTOCOL
* a sub-command for efidebug to display configuration tables
-----BEGIN PGP SIGNATURE-----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=SjPV
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-04-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc1
This pull request provides:
* support for FIT images for UEFI binaries
* drivers for hardware random number generators
* an implementation of the EFI_RNG_PROTOCOL
* a sub-command for efidebug to display configuration tables
- Various fixups for amlogic boards
- Unnecessary header includes drop into video/meson
-----BEGIN PGP SIGNATURE-----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=rkHZ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200108' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- Khadas VIM3L based on Amlogic S905D3 support
- Various fixups for amlogic boards
- Unnecessary header includes drop into video/meson
enable CONFIG_CMD_ERASEENV to make it easy to erase env.
Use savedefconfig to generate new defconfig.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable support for random number generator on sandbox configs. This is
aimed primarily at adding unit test support for rng uclass.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable support for the rng device on the stm32mp15 configs.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Khadas VIM3L uses the same board layout as VIM3, but with an S905D3 chip
instead of A311D. Board config is derived from khadas-vim3_defconfig and
sei610_defconfig. README is based on README.khadas-vim3; the difference
is that VIM3L uses FIP files from the g12a folder in vendor sources not
the g12b folder.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: added vim3l readme into w400 MAINTAINERS]
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeFDfVAAoJEB6zHgIOrC/IKfsH/2cUfXuc9IgA7L90L3g7htlS
zLAQSC8Xk0WbgbmBJh/lq6zFWj2Mu2yfkZqRzwN8bHkmOPq40F+pEAszVtjH77HM
FpSjMSDVWfNXuhmoiS571dehA0TGi1b2kknrAXqpOwVuMRncMCwaPi8yZYZSGlSV
VzMtguQxD0sZg4oMZVde3tCd41smPTPNDjzLZnXdLa0b09+EtW6enGuk3vzXlS/8
QUT68wUzkeoptJhf3pQ3BXNvkFwdNdYJ74uevDmkAYtvxyl10WNykcwYmH50Q9qq
9plF11EizmTHlj16rWpZLx66RP0s4pziKaeGMr6S8uln33Cr9N496wPqtuDBnvA=
=FYPj
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features for 2020.04 cycle
This feature set is a patch series from Tudor Ambarus which includes
parsing of the spi flash SFDP parser for SST flashes, and using those
tables to retrieve unique saved per device MAC address. This is then
used as base mac address on the SAMA5D2 Wireless SOM EK board.
Add build support for Agilex SoC.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The stock U-Boot on Intel Edison has timeout parameter for DFU command.
Enable it here to be compatible with the original U-Boot configuration.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Adjust the environment for booting a mainline kernel by default.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The Embedded Artists COM board is based on NXP i.MX7ULP.
It has a BD70528 PMIC from Rohm with discrete DCDC powering option and
improved current observability (compared to the existing NXP i.MX7ULP EVK).
Add the initial support for the board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
We switch from custom boot commands relying on uEnv.txt to distro boot.
This removes the automatic fpga bitstream loading in favor of loading
bitstreams via custom bootscripts (boot.scr) or after booting the
kernel.
Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Note: gpio7_8 was never used for usb power regulator so we remove it here
Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Sync the Linux Kernel 5.4-rc6 device tree for Phytec Phycore
SoM and Segin board based on imx6UL and imx6ULL.
Changes includes Phytec naming convention for the devicetree files.
Signed-off-by: Parthiban Nallathambi <parthitce@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Enable driver model for SPI and SPI_FLASH to remove the following
compile warning on CM-FX6 SOM:
===================== WARNING ======================
This board does not use CONFIG_DM_SPI_FLASH. Please update
the board to use CONFIG_SPI_FLASH before the v2019.07 release.
====================================================
This change introduced SPL build error as shown:
In file included from include/common.h:47:0,
from drivers/mtd/spi/sf_probe.c:10:
drivers/mtd/spi/sf_probe.c: In function 'spi_flash_std_probe':
drivers/mtd/spi/sf_probe.c:149:54: error: dereferencing pointer to incomplete type 'struct dm_spi_slave_platdata'
scripts/Makefile.build:278: recipe for target 'spl/drivers/mtd/spi/sf_probe.o' failed
make[3]: *** [spl/drivers/mtd/spi/sf_probe.o] Error 1
scripts/Makefile.build:432: recipe for target 'spl/drivers/mtd/spi' failed
make[2]: *** [spl/drivers/mtd/spi] Error 2
Disabling DM for SPI support(SPI and SF) in SPL resolves the issue.
Target was compile tested, build was clean.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Enable CONFIG_DM_ETH to remove compile warning on CM-FX6
SOM based target:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release.
====================================================
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Enable driver model for Video to remove the following
compile warning on CM-FX6 SOM based target:
===================== WARNING ======================
This board does not use CONFIG_DM_VIDEO Please update
the board to use CONFIG_DM_VIDEO before the v2019.07 release.
====================================================
This change introduced build error as shown:
LD u-boot
drivers/built-in.o: In function ipu_displays_init'
arm-linux-ld.bfd: BFD (GNU Binutils) 2.29.1 assertion fail elf32-arm.c:9509
Makefile:1621: recipe for target 'u-boot' failed
make: *** [u-boot] Error 1
The DM converted video driver calls ipu_displays_init
in its probe, which inturn calls relevant board_video_skip.
Defining ipu_displays_init in the board file fixes build error.
Target was compile tested, build was clean.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
The SPL does not have DM enabled and therefor still needs to use the
hardware watchdog interface provided by the imx-watchdog driver.
Fixes: broken reset command after f2929d11a6 ("watchdog: imx: Use
immediate reset bits for expire_now")
Signed-off-by: Claudius Heine <ch@denx.de>
Make first step in DT/DM migration. Enable OF_CONTROL only for the main
U-Boot image for now.
Remove mmc_init_main() because board_mmc_init() is not called when
DM_MMC is enabled.
DM_MMC requires DM_GPIO for card-detect to work. That in turn makes gpio
request mandatory. Add code to request/free gpios in platform code.
MMC devices are now numbered according to DT. The SD card is 1, and eMMC
is 2. Account for that in board_mmc_get_env_dev(), BOOT_TARGET_DEVICES,
and has_emmc().
DM_MMC requires BLK. However, the (BLK && !DM_USB) combination disables
USB_STORAGE. Enable DM_USB to preserve USB functionality. Add also
DM_REGULATORS for the USB power controller. This allows us to drop
board_ehci_hcd_init() and setup_usb().
Runtime selection of DT is necessary because of the i.MX6QD vs i.MX6SDL
incompatibility. DT selection does not rely on GPIOs, since DM_GPIO
depends on DT. Instead, we take one "fully featured" DT of each variant.
That should be enough to boot from both SD card and eMMC.
Since we don't select the exact DT, override the generic
show_board_info() that shows the selected DT 'model' field.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
DM for PCI pulls DM for ethernet that also needs other changes described
below to build u-boot and keep existing functionality - ability to update
MAC addresses of FEC ethernet adapter and I210 adapter connected to the
Marvell switch.
- fec_mxc driver with DM needs PHYLIB;
- configuration items are moved from ge_bx50v3.h to ge_bx50v3_defconfig;
- FEC is marked as eth0 because it is always present, so indices changed:
I210 are still probed in the same order;
- board_eth_init() was used by legacy ethernet, setup for enet iomux and
pcie is moved to the board_late_init();
- pci_init() is called from the board_late_init() to initiate PCI bus
probing, so I210 devices are propagated to the device tree;
Signed-off-by: Denis Zalevskiy <denis.zalevskiy@ge.com>
[Describe PHY reset in device tree]
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
DM should be used for USB since 2019.07, it also requires DM for
regulators.
Signed-off-by: Denis Zalevskiy <denis.zalevskiy@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Use vidconsole for output to the LCD, now that DM_VIDEO is used. Write
white text on a black background, like before migrating to DM_VIDEO.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Fixes commit: 0b09f7b150, which converted
to DM_VIDEO, but requires more memory.
[Inspired by 9002e735e7]
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Copy device trees from linux, keeping them as separate files for
each board to ease future sync.
Update board code to use generic bx50v3 dt initially, then select
the specific dt based on board detection.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
This patch introduces support for i.MX28 based XEA board.
This board supports DM/DTS in U-Boot proper as well as DM aware drivers
in SPL (u-boot.sb) by using OF_PLATDATA.
More detailed information regarding usage of it can be found in
./board/liebherr/xea/README file.
U-Boot SPL 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)
Trying to boot from MMC1
MMC0: Command 8 timeout (status 0xf0344020)
mmc_load_image_raw_sector: mmc block read error
U-Boot 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)
CPU: Freescale i.MX28 rev1.2 at 454 MHz
BOOT: SSP SPI #3, master, 3V3 NOR
Model: Liebherr (LWE) XEA i.MX28 Board
DRAM: 128 MiB
MMC: MXS MMC: 0
Loading Environment from SPI Flash... SF: Detected n25q128a13 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@800f0000 (eth0) using random MAC address - ce:e1:9e:46:f3:a2
eth0: ethernet@800f0000
Hit any key to stop autoboot: 0
Signed-off-by: Lukasz Majewski <lukma@denx.de>
sync defaut Envoronment with customer changes.
Unfortunately they are not changeable, as already
board is in production mode.
Get rid of the big bootcommand and set bootcommand
through Kconfig option.
Signed-off-by: Heiko Schocher <hs@denx.de>
add DM_VIDEO support and remove now unneeded board
code. As we show a bmp logo on boot, call now
bmp_display() from board code and do not use
cfb_console anymore.
Signed-off-by: Heiko Schocher <hs@denx.de>
enable CONFIG_DM_SPI and CONFIG_DM_SPI_FLASH
and get rid of build removal warnings.
define CONFIG_GPIO_ENABLE_SPI_FLASH is not longer
needed, so remove it from config_whitelist.txt
Signed-off-by: Heiko Schocher <hs@denx.de>
Enable DM_GPIO, GPIO_HOG, LED and LED_GPIO as gpio
and LEDs are now defined in DTS. Enable also here
the pinctrl driver, so pinmux setup is also done.
Signed-off-by: Heiko Schocher <hs@denx.de>
add DM_SERIAL support for the aristainetos board, and
remove not used code from board code.
remove CONSOLE_OVERWRITE_ROUTINE.
Signed-off-by: Heiko Schocher <hs@denx.de>
as we switch to support DM and DTS, rework the existing
DTS trees. Change also Linux specific Device trees, goal
is to push this changes to linux.
Collect U-Boot specific changes in separate "*u-boot*" dts
files.
Signed-off-by: Heiko Schocher <hs@denx.de>
remove 2b version of aristainetos board, as it
is easier to make the DM / DTS port and introduce
the 2b board version again (also some more board
version).
Signed-off-by: Heiko Schocher <hs@denx.de>
Bring in the following merges:
commit 8fbbec12f7
Merge: 87f69f467a63618e71e8
Author: Tom Rini <trini@konsulko.com>
Date: Fri Jan 3 09:48:47 2020 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next
- updates and fixes on ls1028a, lx2, ls1046a, MC-DPSPARSER support
commit 87f69f467a
Merge: c0912f9bbf4466b99703
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 24 08:18:19 2019 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next
- Enable DM driver on ppc/km boards
- Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x,
T104x, P4080, P2041, P2020, P1020, P3041
- Some updates in mpc85xx-ddr driver, km boards
commit c0912f9bbf
Merge: 533c9f5714a1d6dc3f84
Author: Tom Rini <trini@konsulko.com>
Date: Wed Dec 18 07:20:19 2019 -0500
Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next
- Various x86 common codes updated for TPL/SPL
- I2C designware driver updated for PCI
- ICH SPI driver updated to support Apollo Lake
- Add Intel FSP2 base support
- Intel Apollo Lake platform specific drivers support
- Add a new board Google Chromebook Coral
commit 533c9f5714
Merge: 553cb06887033e18b47b
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 17 07:53:08 2019 -0500
Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next
i2c: for next
- misc: i2c_eeprom:
Add partition support and add ability to query size
of eeprom device and partitions
- i2c common:
add support for offset overflow in to address and add
sandbox tests for it.
commit 553cb06887
Merge: f39abbbc53b4f98b3b16
Author: Tom Rini <trini@konsulko.com>
Date: Thu Dec 12 08:18:59 2019 -0500
Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next
buildman improvements including toolchain environment feature
sandbox unicode support in serial
- Fix latest mainline kernel for rk3308
- Update rk3288-evb config to suport OP-TEE
- Fix for firefly-px30 DEBUG_UART channel and make it standalone
- Script make_fit_atf add python3 support
- Fix rk3328 timer with correct COUNTER_FREQUENCY
- Fix rk3328 ATF support with enable spl-fifo-mode
Enable the ATF in SPL and adjust the SPL STACK/HEAD at the same time to
support ATF entry at 0x40000.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
U-Boot binary has grown in such a way that it goes beyond the reserved
area for the environment variables.
Running "saveenv" followed by a "reset" causes U-Boot to hang because
of this overlap.
Fix this problem by increasing the CONFIG_ENV_OFFSET size.
Also, in order to prevent this same problem to happen in the future,
use CONFIG_BOARD_SIZE_LIMIT, which will detect the overlap in build-time.
CONFIG_BOARD_SIZE_LIMIT does not accept math expressions, so declare
CONFIG_ENV_OFFSET with its direct value instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Firefly Core-PX30-JD4 use UART2M1 while PX30 evb using UART2M0, the U-Boot
proper will use the dts setting to do the IOMUX init, and a separate dts
is needed for px30-firefly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The Macro has update without update the defconfig, update the defconfig
to make Mcaro correct.
Fixes: ec4fafdf1f ("rockchip: px30: Rename CONFIG_DEBUG_UART2_CHANNEL to...")
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Upstream kernel and rockchip kernel has default enable PSCI which needs
OPTEE in trust word, enable OPTEE support for evb by default and SPL_FIT
option to pack OPTEE with U-Boot proper.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Update the SPL_STACK_R_MALLOC_SIMPLE_LEN which also including space for
STACK and the size may not enough when loding FIT image in SPL.
If the size is not enough, you can see log like this when loding FIT:
U-Boot TPL 2020.01-rc3-00082-g4b19b89ca4-dirty (Dec 05 2019 - 11:52:53)
Trying to boot from BOOTROM
Returning to boot ROM...
U-Boot SPL 2020.01-rc3-00082-g4b19b89ca4-dirty (Dec 05 2019 - 11:52:53 +0800)
Trying to boot from MMC2
And if enable the DEBUG for everyting in SPL, the log will hang at dwmmc
sending CMD16 for 'uboot' loadables binary because this step need a
large stack cost(about 0x2d00).
External data: dst=8400000, offset=72638, size=b3580
Image OS is Trusted Execution Environment
board_fit_config_name_match: rk3288-evb
Selecting config 'rk3288-evb'loadables: 'uboot'
blk_find_device: if_type=6, devnum=1: dwmmc@ff0c0000.blk, 6, 0
blk_find_device: if_type=6, devnum=1: dwmmc@ff0f0000.blk, 6, 1
Sending CMD16
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
In commit <db4080d56dec>, SPL_FSL_PBL is removed from the configs of
some LayerScape platforms. Actually, SPL_FSL_PBL is needed for SD/NAND
boot on LS1021A/LS1043A/LS1046A to create boot binary having SPL binary
in PBI format concatenated with u-boot binary. SPL_FRAMEWORK is used on
these platforms too.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This is the first step to use DM support for the KM powerpc boards.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CC: Mario Six <mario.six@gdsys.cc>
CC: Wolfgang Denk <wd@denx.de>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
Remove this from the board header files and move it to Kconfig. Also use
the correct default address for kmtegr1.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Orangepi Zero Plus 2 is an open-source single-board computer, available
in two Allwinner SOC variants, H3 and H5. We add support for H3 variant
here, as the H5 is already supported.
H3 Orangepi Zero Plus 2 has:
- Quad-core Cortex-A7
- 512MB DDR3
- microSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG + power supply
Sync dts from linux v5.2 commit:
"ARM: dts: sunxi: h3/h5: Remove stale pinctrl-names entry"
(sha1: 75f9a058838be9880afd75c4cb14e1bf4fe34a0b)
Commit:
"ARM: dts: sun8i: h3: Refactor the pinctrl node names"
(sha1: a4dc791974e568a15f7f37131729b1a6912f4811)
has been avoided as it breaks U-Boot build.
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Rsync all defconfig files using moveconfig.py
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Enable the SPI NOR SFDP support and the Microchip QSPI driver.
CONFIG_SPI_FLASH_SFDP_SUPPORT enables the SFDP Vendor parser,
and for the SST case, the retrieval of the ethaddr from the
SPI NOR flash.
While touching the SPI NOR logic, sync with the
sama5d27_wlsom1_ek_qspiflash_defconfig and enable
CONFIG_SPI_FLASH_SPANSION.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
CONFIG_SPI_FLASH_SFDP_SUPPORT enables the SFDP Vendor parser,
and for the SST case, the retrieval of the ethaddr from the
SPI NOR flash.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add support for coral which is a range of Apollo Lake-based Chromebook
released in 2017. This also includes reef released in 2016, since it is
based on the same SoC.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If these phases are used we typically want to enable pinctrl in then, so
that pad setup and GPIO access are possible.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The existing work-around for positioning U-Boot in the ROM when it
actually runs from RAM still exists and there is not obvious way to change
this.
Add a proper Kconfig option to handle this case. This also adds a new bool
property to indicate whether CONFIG_SYS_TEXT_BASE exists.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a sandbox driver and PCI-device emulator for p2sb. Also add a test
which uses a simple 'adder' driver to test the p2sb functionality.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass
is included in SPL/TPL without any control for boards. Some boards may
want to disable this to reduce code size where GPIOs are not needed in
SPL or TPL.
Add a new Kconfig option to permit this. Default it to 'y' so that
existing boards work correctly.
Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to
preserve the current behaviour. Also update the 74x164 GPIO driver since
it cannot build with SPL.
This allows us to remove the hacks in config_uncmd_spl.h and
Makefile.uncmd_spl (eventually those files should be removed).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJd77jyAAoJEB6zHgIOrC/IyYUH/iAUH4wo5qnOBiQU+MJluaiu
D8tMiJH13eW4gWnAqdGrOE9Q763asHIMshQpLK+4eXe4f4mZQ7re4CRNcYJrULeY
2StsJzl4sn/H4P5EiRuUWjkB7wnGRDD6ArH3j1uMJN4lpwCB0ZbqMQZpjt3wI2H4
KuE42d/ll08Aj0AvwdusffLIxlw5M1Z94uQSHoC3UTkPYN4VD5zXgdxv5eH6PZWe
paWmHQ0g7fL4UnYGWa0Jpx10SZpcut06dTeVGpsGiEOhaJHvpjYd4JAs/TTUxhFx
d5ZRjo1fStYmBXQIblhPNlJQkW4cqa/B+81f5aZbN/1yCijJWS2G8anGtY2ikPs=
=f0dF
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2020.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
- First set of u-boot-atmel fixes for 2020.01 cycle:
This set includes a small fix for gpio bank names, one for removing
unused headers (also touches some other boards), and a fix for the QSPI
env read on one of the boards.
The rpi_4_32b_defconfig states that only one DRAM bank is present. This
leads to a wrong configuration of the available DRAM. Fix this by
setting the DRAM bank config accordingly.
Fixes: 193279d784 ("RPI: Add defconfigs for rpi4 (32/64)")
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
bigger than the framebuffer resolution
- reduce dead code in video and console uclass routines
(tested on mx53cx9020, sama5d2_xplained, stm32mp157c-ev1,
stm32f746-disco, stm32f769-disco and wandboard)
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXe//LA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXOqBAJ9N6oTID0v092duxoUoO5xAeqIKxgCfS/YvgGx4
KGgiPWQv0V1bGxXyYNA=
=PoNP
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-2020.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- fix crash and board reset when drawing RLE8 bitmaps
bigger than the framebuffer resolution
- reduce dead code in video and console uclass routines
(tested on mx53cx9020, sama5d2_xplained, stm32mp157c-ev1,
stm32f746-disco, stm32f769-disco and wandboard)
In the initial SPI flash setup, the default bus mode being used was 3,
which is incorrect, causing a CRC error when the ENV was being read from
QSPI. Setting the default bus mode to 0 which is the correct mode.
Signed-off-by: Swapna Gurumani <swapna.gurumani@microchip.com>
- Increase stack size to avoid a stack overflow during distro boot.
- Add hifive-unleashed-a00.dts for SIFIVE FU540.
- Add OF_SEPARATE support for SIFIVE FU540.
- Add SPL support for Andes AX25 AE350.
- Improve U-Boot SPL / OpenSBI smp boot flow for RISC-V.
This patch provides four configurations which can support U-Boot SPL
to boot from RAM or FLASH and then boot FIT image including OpenSBI
FW_DYNAMIC firmware and U-Boot proper images from RAM or MMC boot devices.
With ae350_rv[32|64]_spl_defconfigs:
U-Boot SPL will be loaded by gdb or FSBL and runs in RAM in machine mode
and then load FIT image from RAM device on AE350.
With ae350_rv[32|64]_spl_xip_defconfigs:
U-Boot SPL can be burned into SPI flash and run in flash in machine mode
and then load FIT image from SPI flash or MMC device on AE350.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: KC Lin <kclin@andestech.com>
Cc: Alan Kao <alankao@andestech.com>
This would help to make the necessary changes in drivers and device trees
in U-Boot tree itself. This feature would also be helpful to not pass
dtb during opensbi builds.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Rick Chen <rick@andestech.com>
Enable configs related to DMA and Ethernet so as to support networking at
U-Boot prompt
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
-----------------
- imx8qxp_mek: increase buffer sizes and args number
- Fixes for imx7ulp
- imx8mm: Fix the first root clock in imx8mm_ahb_sels[]
- colibri_imx7: reserve DDR memory for Cortex-M4
- vining2000: fixes and convert to ethernet DM
- imx8m: fix rom version check to unbreak some B0 chips
- tbs2910: Disable VxWorks image booting support
-----BEGIN PGP SIGNATURE-----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=L2zo
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191209' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
Fixes for 2020.01
-----------------
- imx8qxp_mek: increase buffer sizes and args number
- Fixes for imx7ulp
- imx8mm: Fix the first root clock in imx8mm_ahb_sels[]
- colibri_imx7: reserve DDR memory for Cortex-M4
- vining2000: fixes and convert to ethernet DM
- imx8m: fix rom version check to unbreak some B0 chips
- tbs2910: Disable VxWorks image booting support
Many boards do not use all selected framebuffer depth
configurations, for such boards there is some unused
code in video and console uclass routines. Make depth
specific code optional to avoid dead code and slightly
reduce binary size. Also make ANSI code optional for
the same reason. When i.e. using only VIDEO_BPP16 the
code size shrinks (below values when using gcc-7.3.0):
$ ./tools/buildman/buildman -b video-wip -sS wandboard
...
01: Merge git://git.denx.de/u-boot-sh
02: video: add guards around 16bpp/32bbp code
03: video: make BPP and ANSI configs optional
arm: (for 1/1 boards) all -776.0 bss -8.0 text -768.0
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
- rockchip pwm driver update to support all the SoCs
- RK3308 GMAC and pinctrl support
- More UART interface support on PX30 and pmugrf reg fix
- Fixup on misc for eth_addr/serial#
- Other updates on variant SoCs
The fitImage support was enabled in the downstream U-Boot port and the
kernel images on the device are fitImage, yet this functionality is not
enabled in mainline U-Boot. Enable it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Convert the board to ethernet DM support. Adjust board file accordingly,
as the board_eth_init() contains custom clock configuration required for
this board to work. Furthermore, enable FEC1 clock to make FEC1 work as
well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable DRAM calibration in SPL to improve behavior of the board
in edge conditions of the thermal envelope of the board and make
it even more stable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
In preparation for use of DDR DRAM fine-tuning upon boot,
convert the board to SPL framework instead of using DCD
tables to bring up DRAM and pinmux.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
U-Boot binary has grown in such a way that it goes beyond the reserved
area for the environment variables.
Running "saveenv" followed by a "reset" causes U-Boot to hang because
of this overlap.
Fix this problem by increasing the CONFIG_ENV_OFFSET size.
Also, in order to prevent this same problem in the future, use
CONFIG_BOARD_SIZE_LIMIT, which will detect the overlap in build-time.
CONFIG_BOARD_SIZE_LIMIT does not accept math expressions, so declare
CONFIG_ENV_OFFSET with its direct value instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Acked-by: Joris Offouga <offougajoris@gmail.com>
Tested-by: Joris Offouga <offougajoris@gmail.com>
This enables reading of the cpuid and a static MAC address.
Signed-off-by: Ben Wolsieffer <benwolsieffer@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This is a core board named Core-PX30-JD4 with a mainboard from Firefly,
name it as firefly-px30 for now.
This board can re-use the dts of PX30, the only difference is the UART IO,
the firefly use UART2 M1 while evb use UART2 M0.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
SPL has limited available resources, and the performance between
ARM and Thumb isn't that significant.
This patch builds using Thumb instruction set to reduce the code
size by nearly 6K.
Original:
text data bss dec hex filename
26526 4004 1376 31906 7ca2 spl/u-boot-spl
Thumb:
text data bss dec hex filename
20232 4004 1376 25612 640c spl/u-boot-spl
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The da850-evm doesn't have the boot pins configured in a way
to make MMC/SD booting an option, and MMC/SD support is not
enabled in SPL. Therefore, there is no need to support raw mode
mmc/sd support in SPL.
This patch disables CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
Signed-off-by: Adam Ford <aford173@gmail.com>
CONFIG_DFU_NAND needs the raw NAND core being compiled.
Also fix the colibri_vf defconfig to reflect this dependency.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Enabling TFABOOT configuration will compile-in a call to nand_read in
the boot sequence. Handle the situation by also selecting officially
the raw NAND core in this case.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is no flash on this board, there is no reason to define MTD
environment variables nor UBI. Drop them from the configuration file.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Wolfgang Grandegger <wg@aries-embedded.de>
While the right Kconfig entries were selected, because of the missing
CMD_NAND symbol the raw NAND core was never compiled. Remove it from
the defconfigs otherwise the build will fail.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Also do this on bcm11130_nand]
Signed-off-by: Tom Rini <trini@konsulko.com>
Due to previous Makefile organization, the raw NAND subdirectory was
not compiled in if CMD_NAND was not enabled. Because the Denali driver
does not compile with these boards (undefined environment offset),
remove the dependency within the defconfig over the controller driver
(was ignored anyway in the past).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's be consistent and always declare CONFIG_MTD from the defconfig
file when needed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
MTD support must be enabled when using mtdparts. Indeed, functions
like get_mtd_info(), get_mtd_device() and put_mtd_device() are in
drivers/mtd/mtd_uboot.c and are built only with CONFIG_MTD.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
In some files, options of CMD_NAND are selected but not the command
itself. Fix this inconsistency.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Raw NAND support must be enabled when the environment is in NAND.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
UBI must be enabled when the environment is in UBI.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
UBI must be enabled when using fastmap, reflect this is defconfigs.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
MTD must be enabled when there is a SPI NOR flash using the
SPI_FLASH_MTD config entry.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Both symbols must be enabled when there is a raw NAND driver
selected. Also enable them when CONFIG_CMD_NAND is selected to avoid
breaking things when we'll further rework the MTD dependency
description.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
[trini: Rebase and migrate a few more boards here]
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable DM_SPI and DM_SPI_FLASH in U-Boot on M2N Gose.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable DM_SPI and DM_SPI_FLASH in U-Boot on M2W Koelsch.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable DM_SPI and DM_SPI_FLASH in U-Boot on H2 Lager.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Like in Linux, just use CONFIG_MTD to compile the MTD stack.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
CONFIG_MTD must be reserved for the MTD core. Like any other
subsystem, prefix the symbol by DM when it comes to DM support.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
[trini: Add Kconfig files]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
This adds a general board file based on MT8518 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
This commit is adding the basic boot support for the MT8518 eMMC board.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
[trini: Migrate env location to defconfig, set ENV_IS_IN_MMC]
Signeed-off-by: Tom Rini <trini@konsulko.com>
In order to further prepare for full device tree support in SPL,
this patch enables both SPL_DM_SEQ_ALIAS and SPL_OF_TRANSLATE.
Both of these are already enabled in U-Boot, so SPL will have
the same functionality
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Driver model requires a malloc pool to allocate memory before
relocations to operate serial and some other devices. This patch
increases the pool size to 2K.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
In preparation to use full device tree support, SPL can separate
BSS from text region.
This patch enables SPL_SEPARATE_BSS.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This converts the following to Kconfig:
CONFIG_SYS_CORTINA_FW_IN_MMC
CONFIG_SYS_CORTINA_FW_IN_NAND
CONFIG_SYS_CORTINA_FW_IN_NOR
CONFIG_SYS_CORTINA_FW_IN_REMOTE
CONFIG_SYS_CORTINA_FW_IN_SPIFLASH
Signed-off-by: Tom Rini <trini@konsulko.com>
There are currently no known users of this functionality on this
platform, disable it to prepare for additional VxWorks functionality
that would cause this platform to fail to link.
Cc: Soeren Moch <smoch@web.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Soeren Moch <smoch@web.de>
There are currently no known users of this functionality on this
platform, disable it to prepare for additional VxWorks functionality
that would cause this platform to fail to link.
Cc: Soeren Moch <smoch@web.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Soeren Moch <smoch@web.de>
The deadline for migration to CONFIG_DM is v2020.01. The VCT
baords would need an almost complete rewrite of all drivers to
support driver model.
Unless someone has access to the hardware and volunteers to do the migration,
the board should be scheduled for removal.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Since at least some of the drivers relevant to LS1028A are now following
DM, it's useful to have dm command enabled by default.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
- Device tree alignment on v5.4-rc4 for all stm32 boards
- Correct the eMMC pin configuration on stm32mp157c-ev1
- Add DFU and SPI-NAND support for stm32mp1 board
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl3dN0YACgkQ4rK92eCq
k3WlywgAisVONrdkoC345Kq1vQRcKGYxcWVd0IWkuK3QZ4KrMRQrhEqXhmR7OhWD
4YrAlgV6FEBTlacfKKsxaL7MJ3VK+h5YLvqoGzZS2Inmrx09v6rOofVTRevmB4Qz
SlIeUKVBijORmRi31I/WcLdiPgd3RR53wQgAugU3PUpuoUb1Z+sJdOreOkl5qGyZ
8aRgvG/if8afILXfH/a4IUuPboaVjaC5B20JCzX4M4ks8lHJ3atbtawgj/e41yYv
Ybq3QudM62g4SvTgJ5/1yqjQ4Oj8dkAY7JyAiXfHa9Kip7s16aBDFklDH7eR9v7F
IxyoYcFhuPADE7ApdWtij/y/KRS66Q==
=oVPG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20191126' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Solve warning for stih410-b2260
- Device tree alignment on v5.4-rc4 for all stm32 boards
- Correct the eMMC pin configuration on stm32mp157c-ev1
- Add DFU and SPI-NAND support for stm32mp1 board
LS1028A QDS board supports multiple combinations of SerDes protocols and
multiple add-on cards with Ethernet PHYs. Some of them require specific
configuration in Linux DT, and the plan is to use DT overlays for them.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add read for OTP and PMIC NVM with alternates
on virtual DFU device.
Serie-cc: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Activate the support of SPI NAND in stm32mp1 U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of DFU for MMC, MTD, RAM and MTD command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch allows to fix the following compilation warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
- fix boot banner on RPi3/4
- add support for one binary on RPi3/4
-----BEGIN PGP SIGNATURE-----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=4Z+A
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2020.01' of https://github.com/mbgg/u-boot
- add RPi4 upstream compatible to pinctrl
- fix boot banner on RPi3/4
- add support for one binary on RPi3/4
Enable the support of function keys on the USB keyboard. This is necessary
to test the USB keyboard driver.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Provide a defconfig which allows us to boot Raspberrry Pi 4
and Raspberry Pi 3 Model B/B+
Instead of using the embedded DTB as done in RPi3 we use the
devicetree provided by the firmware.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
- Clean vid/pid in Kconfig and add fastboot for rk3399
- add 'u-boot, spl-fifo-mode' for mmc
- Use FIT generator for rk3229 optee and rk3368 ATF
- fan53555: add support for Silergy SYR82X and SYR83X
Enable DWC3 core, gadget for rock960 board.
This would help to use fastboot by default.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use CONFIG_EFI_LOADER=n for ARM11 except for the Raspberry Pi and the
Raspberry Pi Zero.
-----BEGIN PGP SIGNATURE-----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=zDGP
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-01-rc4-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-01-rc4 (2)
Use CONFIG_EFI_LOADER=n for ARM11 except for the Raspberry Pi and the
Raspberry Pi Zero.
Select CONFIG_FASTBOOT_FLASH, CONFIG_FASTBOOT_FLASH_MMC_DEV
for rockchip SoC plaforms in fastboot Kconfig file instead
of defined it in board defconfig.
This eventually drop the explicit configs defined in
supporting board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip support differnet or common gadget product number
between Rockchip SoCs like,
0x310a - rk3036
0x320a - rk3229, rk3288
0x330a - rk3328
So, select them on Kconfig based on platform specific
config defined.
This eventually drop the explicit configs defined in
supporting board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Gadget vendor number, 0x2207 is common across all platfroms
supported in Rockchip SoC.
So, select the same number globally, if ARCH_ROCKCHIP.
This eventually drop the explicit configs defined in supported
board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Select the gadget manufacturer as 'Rockchip' for
all rockchip platform SoC's.
This eventually drop the explicit defined added
on supported board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK3368 lion board ATF can use bl31.elf like RK3399 and get the FIT
source with generic FIT generator script at:
arch/arm/mach-rockchip/make_fit_atf.py
And then we can use 'BL31' environment to get the path of bl31.elf
instead of copy it into U-Boot folder.
CC: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use generator script so that we can use environment for TEE source.
$TEE for tee.bin, and if file not exist, the script can report a warning,
and meke the build success without a error.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Some of the ARM11 boards have tight limits on the size of U-Boots. Hence
use EFI_LOADER=n as default on ARM11.
Set EFI_LOADER=y for the Raspberry Pi and Raspberry Pi Zero as these boards
have sufficient storage on the SD card.
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The default mtdparts value grew a trailing zero during the Kconfig
conversion. This is because the mtdparts value in the header file
had a \0 at the end, which got misconverted into plain 0 instead of
being dropped.
Signed-off-by: Marek Vasut <marex@denx.de>
Fixes: 43ede0bca7 ("Kconfig: Migrate MTDIDS_DEFAULT / MTDPARTS_DEFAULT")
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit 2a51e16bd5 ("configs: Make USE_TINY_PRINTF depend on SPL||TPL and be default")
enable USE_TINY_PRINTF by default, disable it for Stratix10.
Resync with savedefconfig.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Support tinker-s board. The board is equivalent of tinker board
except of emmc.
TODO:
- support of usb current burst when the board is powered from pc
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
ROC-RK3308-CC is a rk3308 based board designed by
Firelfy, with eMMC and 256MB DDR3 and RTL8188 Wifi
on board.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rockpro64 needs to setup I/O domains in order for USB to work in u-boot.
Since we currently don't have a driver to do that, split it into its own
board file and initialize I/O domains here.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable TPL for rock960 like other rk3399 boards.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
roc-rk3399-pc_defconfig is committed in below
commit <8a681f4c5aa15db51ad0209734859c9fe7c29cfd> ("rockchip: rk3399:
Add ROC-RK3399-PC support")
which doesn't follow the existing defconfigs on rk3399.
So, rename as followed with other rk3399 defconfigs.
Cc: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The px30 evb is an evaluation board for the px30 together with a dsi-
connected display. This adds board and config files for it.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RK3328 has a similar controller and phy with PX30, so we can use the
common driver for it and remove the duplicate codes.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Enable CONFIG_ARCH_FIXUP_FDT_MEMORY to let U-Boot patch the
Linux DT memory entries.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move this symbol to Kconfig. As part of this we can drop a UBI-specific
symbol that was a stop-gap for not having this particular symbol in
Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is setting CONFIG_ENV_IS_IN_SPI_FLASH in the header rather
than defconfig, fix.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is setting CONFIG_ENV_IS_IN_MMC in the header rather than
defconfig, fix.
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tom Rini <trini@konsulko.com>