This patch adds the board specific configuration (struct) for the
Octeon 3 EBB7304 EVK. This struct is ported from the 2013er Cavium /
Marvell U-Boot repository. Also, the Octeon RAM driver is enabled in
the board defconfig for its usage.
Tested with one and two DIMMs on the EBB7304 EVK (8 & 16 GiB).
Signed-off-by: Stefan Roese <sr@denx.de>
According to doc/README.distro fdt_addr must not be set when DTB is not
available from hardware. So remove this entry.
Use address 32MB above the start of DRAM for kernel_addr_r. This way
we likely can avoid the self-relocation of the compressed kernel image
before it decompresses to offset 0x8000 from start of DRAM.
Use address 128MB above the start of DRAM for fdt_addr_r, since this is
the maximum location for the end of the kernel. So we avoid overwriting
the DTB.
Use 512k above that for ramdisk_addr_r. This should be enough for the
DTB, rest of DRAM can be used for initrd.
Place boot script / extlinux.conf at offset 0 / 1MB from start of DRAM.
This space is available for processing in U-Boot.
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable the RPC Hyperflash driver on R8A7795,R8A7796,R8A77965
Salvator-X,ULCB and R8A77990 Ebisu. Note that to make the HF
accessible, mainline ATF is mandatory and must be built with
RCAR_RPC_HYPERFLASH_LOCKED=0 . Note that this is intended for
development and testing convenience only and must be disabled
in deployment for platform security reasons.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX2x4MgAKCRDKSWXLKUoM
IZQtAJ9HpNwG5q3nHt9WedzLCTkr3YoLAACeJJ0Wlpp5p5xPzuPmnoo/Vi4MtNQ=
=yxRo
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.01
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
Increase max gunzip size, required for booting itb recovery images on
uDPU.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
[a.heider: adapt to mainline]
Signed-off-by: Andre Heider <a.heider@gmail.com>
scan_dev_for_efi is supposed to be called from scan_dev_for_boot.
However this call is missing for ls1028ardb and ls1028aqds boards. As
a result EFI boot doesn’t work. Fix this issue by removing custom
definition of scan_dev_for_boot and use the default definition
instead.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: andy.tang@nxp.com
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
PXE and DHCP shouldn't be listed when commands are not enabled that's why
handle it in the same way as is done for Zynq and ZynqMP.
Fixes: ec48b6c991 ("arm64: versal: Add support for new Xilinx Versal ACAPs")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch does sed 's/SPL_FPGA_SUPPORT/SPL_FPGA/g' but also fixing Makefile
and zynqmp.c to simplify if/endif logic in zynqmp.c.
This change is mostly done to be able to use CONFIG_IS_ENABLED macro and
obj-$(CONFIG_$(SPL_)FPGA) in Makefile. For them symbols need to be in sync.
And removing one line from Topic Miami boards which is not needed because
symbol is not enabled via Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch moves the the config SYS_MALLOC_LEN to Kconfig
as it is already done for zynq arch in commit 01aa5b8f05
("Kconfig: Move config SYS_MALLOC_LEN to Kconfig for zynq").
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Provide fdtfile value in default env instead of setting
it dynamically in runtime.
Fixes: 85cb2bc686("apalis/colibri imx6: provide proper fdtfile value")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Provide fdtfile value in default env instead of setting
it dynamically in runtime.
Fixes: 85cb2bc686("apalis/colibri imx6: provide proper fdtfile value")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Fixes: a62c60610f("colibri_imx7_emmc: add Colibri iMX7D 1GB (eMMC) module support")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Fixes: 304042c1f3("colibri_vf: set fdtfile for distroboot")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Fixes: board: 31b1e17f44("toradex: add Colibri iMX6ULL support")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Set proper splashscreen env value instead of calling legacy function
to show embed boot logo.
Fixes: 195011b24d("colibri-imx7: fix splash logo drawing")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Set proper splashscreen env value instead of calling legacy function
to show embed boot logo.
Fixes: 391c712dde("colibri-imx6ull: show boot logo")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
enable DTS support for keymile mpc83xx based boards.
get rid of compile warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Therefore done:
- add DTS for all mpc83xx based boards from keymile
mainly they are not mainlined to linux.
- add u-boot specific dtsi
- add stdout-path
- add missing ucc4 par_io definitions, which were
in board code, but not in linux DTS
- remove not used ethernet nodes
Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Series-to: u-boot
Series-version: 3
Series-changes: 3
- rebase patchset to current mainline commit
c0192950df
- update defconfig files
Series-changes: 2
- add patch which fixes Codingstyle errors in drivers/qe
- add patch which converts the mpc83xx based boards from
keymile to DM_ETH
Cover-letter:
powerpc, mpc83xx: add DM_ETH support
This patch series adds DM ethernet support for mpc83xx based
keymile boards.
Travis build:
END
Add platform data and a device structure for the spi device
present on am335x-icev2. This requires moving all omap3_spi
platform data structures and symbols to an omap3_spi.h so that
the board file can access them.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
The R5 SPL on J7200 SoCs will be limited to booting just the
MCU R5FSS0 R5F core in LockStep-mode at present, so add the
two required environment variables 'addr_mcur5f0_0load' and
'name_mcur5f0_0fw' that are needed by the R5 SPL early-boot
logic. The firmware name used is also different from that on
J721E SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
The J7200 SoCs have different number of remote processors, but reuse
the same environment settings as the J721E SoCs. The current env
variable rproc_fw_binaries is geared towards J721E SoCs and is
incorrect for J7200 SoCs. Please see the logic originally added in
commit 0b4ab9c9a7 ("env: ti: j721e-evm: Add support to boot rprocs
including R5Fs and DSPs").
Fix this by defining the DEFAULT_RPROCS macro appropriately using
the corresponding TARGET_EVM Kconfig symbol. This macro is used by
the 'rproc_fw_binaries' env variable in the common remoteproc env
header file k3_rproc.h.
The list of R5F cores to be started before loading and booting the
Linux kernel are as follows, and mainly comprises of the Main R5FSS0
cores in this order:
Main R5FSS0 (Split) Core0 : 2 /lib/firmware/j7200-main-r5f0_0-fw
Main R5FSS0 (Split) Core1 : 3 /lib/firmware/j7200-main-r5f0_1-fw
The MCU R5FSS0 is in LockStep mode and is expected to be booted by
R5 SPL, so it is not included in the list. The order of rprocs to
boot cannot be really modified as only the Main R5FSS0 cores are
involved and Core0 has to be booted first always before the
corresponding Core1.
Signed-off-by: Suman Anna <s-anna@ti.com>
The commit 316c927135 ("include: configs: j721e_evm: Add env variables
for mcu_r5fss0_core0 & main_r5fss0_core0") added four different new env
variables 'addr_mainr5f0_0load', 'name_mainr5f0_0fw', 'addr_mcur5f0_0load'
and 'name_mcur5f0_0fw' to the generic environment, but these are only
needed and used in R5 SPL for early-booting the MCU R5FSS0 and Main
R5FSS0 Core0 on J721E SoCs.
These are not really needed for A72 U-Boot, so limit the scope of
these variables only to R5 SPL. While at this, also fix the loadaddr
variable values to include the hex prefix like with other such env
variables.
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
The default rproc list currently used by A72 U-Boot to boot various
remote processors include the Main R5FSS0 (Split-mode) Core1, Main
R5FSS1 (LockStep mode) Core0 and the three DSPs. The Main R5FSS1 cluster
is configured for Split mode by default in the dts now, so add the
Main R5FSS1 Core1 (rproc #5) to the default rproc boot list. This
core is now booted after the Main R5FSS1 Core0 and before the DSPs.
The order of the rprocs to boot can always be changed at runtime if
desired by overwriting the 'rproc_fw_binaries' environment variable
at U-boot prompt. Note that the R5FSS Core1 cannot be booted before
its associated Core0.
Signed-off-by: Suman Anna <s-anna@ti.com>
Boot scripts for existing Espressobin Linux distributions, like OpenWRT,
expect that U-Boot set fdt_addr and kernel_addr envs. So add env aliases
from fdt_addr_r and kernel_addr_r values.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
Current loadaddr is not writable on Espressobin and 'loadb' command cause
rebooting board. Marvell's U-Boot already set default loadaddr to value
0x06000000 [1] and after this change 'loadb' is working fine.
[1] - 0a5b159806
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
According to Marvell's U-Boot description [1] current env load addresses
overlaps with ATF RT services region and TEE. Because the ATF RT service
and TEE region is going to be marked as secure and can't be overwritten,
use different different addresses for envs.
[1] - 0a5b159806
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- Add basic Marvell/Cavium OcteonTX/TX2 support (Suneel)
- Infrastructure changes to PCI uclass to support these SoC's (Suneel)
- Add PCI, MMC & watchdog driver drivers for OcteonTX/TX2 (Suneel)
- Increase CONFIG_SYS_MALLOC_F_LEN for qemu-x86 (Stefan)
Restrict the memory range available for image processing in the
"bootm" to 256 MiB so the kernel can access it and FDT or initrd are
not overwritten on ARM64.
Signed-off-by: Grygorii Tertychnyi <grygorii.tertychnyi@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The loading address is too close to the kernel address, so newer kernels
may overlap memory space, so loading the device tree may corrupt zImage.
This patch moves the fdt_addr_r to 0x14000000 which is also consistent
with guidance that the kernel be allocated 32MB. This places it
in the same place as the ramdisk, so this patch moves the ramdisk address
512KB after the fdt.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
We have a number of platforms that are a combination of a carrier board
and System-on-Module (SoM) that in turn allows for the board to have
different SoCs on it. In some cases, this is handled via board-specific
Kconfig options. In other cases we make use of
CONFIG_SYS_EXTRA_OPTIONS. This latter case however can lead to invalid
configurations as we will not in turn get options that in Kconfig are
selected by or depend on that setting.
To resolve this, make the SoC option a choice in Kconfig and make boards
depend on what they can support. This change opens us up for further
clean-ups in the cases where a single CONFIG_TARGET_xxx can support
different SoCs and today they do not, or do not cleanly do so.
Reported-by: Matt Porter <mporter@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Soeren Moch <smoch@web.de>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Cc: Ian Ray <ian.ray@ge.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Cc: Simone CIANNI <simone.cianni@bticino.it>
Cc: Adam Ford <aford173@gmail.com>
Cc: Marcin Niestroj <m.niestroj@grinn-global.com>
Cc: "Eric Bénard" <eric@eukrea.com>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Cc: Eric Nelson <eric@nelint.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Parthiban Nallathambi <parthiban@linumiz.com>
Cc: Marek Vasut <marex@denx.de>
Cc: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Niel Fourie <lusus@denx.de>
Cc: Martyn Welch <martyn.welch@collabora.com>
Cc: Richard Hu <richard.hu@technexion.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Arkadiusz Karas <arkadiusz.karas@somlabs.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
Cc: Silvio Fricke <open-source@softing.de>
Tested-by: Matt Porter <mporter@konsulko.com> [colibri_imx6]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This patch adds support for all OcteonTX2 96xx/95xx
boards from Marvell.
For 96xx boards, use octeontx_96xx_defconfig and
for 95xx boards, use octeontx_95xx_defconfig.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
This patch adds support for all OcteonTX 81xx/83xx
boards from Marvell.
For 81xx boards, use octeontx_81xx_defconfig and
for 83xx boards, use octeontx_83xx_defconfig.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
CONFIG_CMD_RUN is set on by default in Kconfig.
Create xenguest_arm64_defconfig by using savedefconfig to avoid unnecessary
options.
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Total Compute is based on ARM architecture and has
the following features enabled in u-boot:
- PL011 UART
- PL180 MMC
- NOR Flash
- FIT image with Signature
- AVB
Signed-off-by: Usama Arif <usama.arif@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPLASH_SCREEN
CONFIG_SPLASH_SCREEN_ALIGN
CONFIG_SPLASHIMAGE_GUARD
CONFIG_SPLASH_SOURCE
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no need to setup this variable if bootm_low and bootm_size
variable are properly setup. If fdt_high variable is missing U-Boot is
asking LMB to return free memory which is not used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable DFU tftp support for firmware update. Fill dfu_ram_tftp variable to
have command present for showing how to use it.
boot FIT image has been created from below fragment. Key part is that type
of image has to be firmware. Also based on experiment load property is
completely ignored and base addresses are taken from dfu_alt_info variable.
$ cat update_uboot.its
/dts-v1/;
/ {
description = "Automatic U-Boot update";
#address-cells = <1>;
images {
Image {
description = "Kernel";
data = /incbin/("/tftpboot/Image");
compression = "none";
arch = "arm64";
type = "firmware";
os = "linux";
load = <0x80000>;
entry = <0x80000>;
hash-1 {
algo = "sha1";
};
};
system.dtb {
description = "DTB";
data = /incbin/("/tftpboot/system.dtb");
compression = "none";
arch = "arm64";
type = "firmware";
load = <0>;
hash-1 {
algo = "sha1";
};
};
};
};
$ mkimage -f update_uboot.its /tftpboot/boot
When U-Boot starts get IP address and server IP.
dhcp
setenv serverip 192.168.0.105
And then run prepared command.
run dfu_ram_tftp
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Image should be loaded to 0x80000 address and not to $kernel_addr_r.
Also kernel_addr, fdt_addr and fdt_size in zynqmp case are not defined
that's why define it to be aligned with Versal.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mini U-boot runs on lower foot print of 256KB OCM. Hence 8K memory
for malloc may not be required. Reduce it by 1.5K.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This series includes bug fixes for:
* UEFI secure boot - images with multiple signatures
* UEFI secure boot - support for intermediate certificates
* corrections for UEFI unit tests
* missing loadaddr on MAIX board
-----BEGIN PGP SIGNATURE-----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=0ZD1
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-10-rc3-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-10-rc3 (2)
This series includes bug fixes for:
* UEFI secure boot - images with multiple signatures
* UEFI secure boot - support for intermediate certificates
* corrections for UEFI unit tests
* missing loadaddr on MAIX board
Add initial infrastructure for Xen para-virtualized block device.
This includes compile-time configuration and the skeleton for
the future driver implementation.
Add new class UCLASS_PVBLOCK which is going to be a parent for
virtual block devices.
Add new interface type IF_TYPE_PVBLOCK.
Implement basic driver setup by reading XenStore configuration.
Signed-off-by: Andrii Anisov <andrii_anisov@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Introduce a minimal Xen guest board running as a virtual
machine under Xen Project's hypervisor [1], [2].
Part of the code is ported from Xen mini-os and also uses
work initially done by different authors from NXP: please see
relevant files for their copyrights.
[1] https://xenbits.xen.org
[2] https://wiki.xenproject.org/
Signed-off-by: Andrii Anisov <andrii_anisov@epam.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Move the BOOTCOMMAND definition from the board inclusion
header to the default configuration file.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
The hardcoded platform variables such as DRAM base address are not
common to Aspeed SoCs AST24xx/AST25xx/AST26xx. This patch replaces
those hardcoded with macros defined in a newly added header, where
the basic SoC HW information are assigned accordingly.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
j7200-evm has minor differences with j721e-evm based on the IPs
available in the SoC. Introduce separate build targets for j7200-evm
to incorporate the differences.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
This converts the following to Kconfig:
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART
Note that with this conversion we now have consistent behavior with
respect to ensuring that we have always selected the correct MMC
device and hardware partition.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove ad-hoc CONFIG_SYS_SRAM_START and use CONFIG_SYS_SRAM_BASE instead.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
This converts ad-hoc CONFIG_SYS_SRAM_SIZE to Kconfig.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
This converts ad-hoc CONFIG_SYS_SRAM_BASE to Kconfig.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
This commit moves CONFIG_PREBOOT="usb start" to common/KConfig
for all boards also declaring USB_KEYBOARD.
Besides simplifying defconfig files, this also enables support for
board-specific CONFIG_PREBOOT for sunxi boards:
commit 37304aaf60 ("Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to
Kconfig") intended to support CONFIG_PREBOOT, but
include/configs/sunxi-common.h hardcodes preboot as part of internally
defined CONSOLE_STDIN_SETTINGS, silently ignoring any board-specific
CONFIG_PREBOOT.
Signed-off-by: Jonas Smedegaard <dr@jones.dk>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Series-Cc: Jagan Teki <jagan@amarulasolutions.com>
Series-Cc: Lukasz Majewski <lukma@denx.de>
Series-Cc: Andre Przywara <andre.przywara@arm.com>
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXykjtQ8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76a1WQCcD+objdS+90mDdT0yTpW3jHS4YiwAn2V2rTTo
4hKj5yxRg3cvb/pBAmbQ
=TyRs
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20200804' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
For 2020.10
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
MYS-6ULX is single board computer (SBC) comes with eMMC or NAND based
on imx6ULL SoC from NXP and provision for expansion board. This
commit adds support only for SBC with NAND.
CPU: Freescale i.MX6ULL rev1.1 528 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 45C
Reset cause: WDOG
Model: MYiR i.MX6ULL MYS-6ULX Single Board Computer with NAND
Board: MYiR MYS-6ULX 6ULL Single Board Computer
DRAM: 256 MiB
NAND: 256 MiB
MMC: FSL_SDHC: 0
In: serial@2020000
Out: serial@2020000
Err: serial@2020000
Net: FEC0
Working:
- Eth0
- MMC/SD
- NAND
- UART 1
- USB host
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Switch r2dplus to DM and DT probing for serial and clock.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
- fix SPL boot issue due to early dbgmcu_init() call
- fix SPL boot issue due to dcache memory region configuration
- add support of CONFIG_ENV_IS_IN_MMC
- add specific SD/eMMC partition for U-Boot enviromnent
- enable env in SPL
- use "env info -q" to remove log during boot
- remove env location override for dh_stm32mp1
- update management of misc_read
- check result of find_mmc_device in stm32prog
- use regulator_set_enable_if_allowed for disabling vdd supply in usbphyc
- enable CMD_ADTIMG flag to handle Android images
- device tree alignment with Linux Kernel v5.8-rc1
- remove hnp-srp-disable for usbotg on dk1
- add reset support to uart nodes on stm32mp15x
- use correct weak function name spl_board_prepare_for_linux
- use cd-gpios for ST and DHSOM boards
- add seeed studio odyssey-stm32mp157c board support
- move ethernet PHY into SoM DT
- add DHSOM based DRC02 board support
Add support for flashing images into QSPI and eMMC.
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for Broadcom Northstar 3 SoC.
NS3 is a octo-core 64-bit ARMv8 Cortex-A72 processors
targeting a broad range of networking applications.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- Configuration changed, mainly several "CONFIG_..." moved from
s5p4418_nanopi2.h to s5p4418_nanopi2_defconfig and USB related
configs removed because USB is not supported yet.
- s5p4418_nanopi2.h: "CONFIG_" removed from several s5p4418/nanopi2
specific defines because the appropriate values do not need to be
configurable.
- pinctrl is supported now, therefore "CONFIG_PINCTRL=y" added to
s5p4418_nanopi2_defconfig.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Some instructions in the ARM ISA have multiple output registers, such
as ldrd/ldp (load pair), where two registers are loaded from memory,
but also ldr with indexing, where the memory base register is incremented
as well when the value is loaded to the destination register.
MMIO emulation under KVM is based on using the architecturally defined
syndrome information that is provided when an exception is taken to the
hypervisor. This syndrome information describes whether the instruction
that triggered the exception is a load or a store, what the faulting
address was, and which register was the destination register.
This syndrome information can only describe one destination register, and
when the trapping instruction is one with multiple outputs, KVM throws an
error like
kvm [615929]: Data abort outside memslots with no valid syndrome info
on the host and kills the QEMU process with the following error:
U-Boot 2020.07-rc3-00208-g88bd5b179360-dirty (Jun 06 2020 - 11:59:22 +0200)
DRAM: 1 GiB
Flash: error: kvm run failed Function not implemented
R00=00000001 R01=00000040 R02=7ee0ce20 R03=00000000
R04=7ffd9eec R05=00000004 R06=7ffda3f8 R07=00000055
R08=7ffd9eec R09=7ef0ded0 R10=7ee0ce20 R11=00000000
R12=00000004 R13=7ee0cdf8 R14=00000000 R15=7ff72d08
PSR=200001d3 --C- A svc32
QEMU: Terminated
This means that, in order to run U-Boot in QEMU under KVM, we need to
avoid such instructions when accessing emulated devices. For the flash
in particular, which is a hybrid between a ROM (backed by a read-only
KVM memslot) when in array mode, and an emulated MMIO device (when in
write mode), we need to take care to only use instructions that KVM can
deal with when they trap.
So override the flash read accessors that are used when running on QEMU
under KVM. Note that the the 64-bit wide read and write accessors have
been omitted: they are never used when running under QEMU given that it
does not emulate CFI flash that supports it.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Done with:
./tools/moveconfig.py -S SPL_LOAD_FIT_ADDRESS
./tools/moveconfig.py -S SPL_LOAD_FIT_ADDRESS -H
Signed-off-by: Peng Fan <peng.fan@nxp.com>
[trini: A few more migrations]
Signed-off-by: Tom Rini <trini@konsulko.com>
BOOTP_DEFAULT is defined in several boards, but this config
option is never checked or used.
This patch removes this config option from config files and
the whitelist.txt
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_SPL_NAND_DRIVERS
CONFIG_SPL_NAND_ECC
CONFIG_SPL_NAND_SIMPLE
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>
Activate the new option -q in command "env info"
to avoid unnecessary trace during boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
- Bug fixes and updates on ls2088a,ls1028a, ls1046a, ls1043a, ls1012a
- lx2-watchdog support
- layerscape: pci-endpoint support, spin table relocation fixes and
cleanups
- fsl-crypto: RNG support and bug fixes
Previous attempt to increase CONFIG_SYS_MALLOC_LEN was done in commit
c084a8edf4 ("configs: ls1012a: Increase CONFIG_SYS_MALLOC_LEN size")
which increased malloc memory to ~1M.
PFE firmware alone requires 3M of dynamic memory allocation and
therefore, increase the config value to a larger value i.e 5M. This size
should be enough as of now to accommodate further memory requirements.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The eSDHC adapter card identification and multiplexing configuration
through FPGA had been implemented in both common mmc driver and
fsl_esdhc driver. However it is proper to move these code to board
files and do it during board initialization. The FPGA registers are
also board specific.
This patch is to move eSDHC adapter card identification and
multiplexing configuration from mmc driver to specific board files.
And the option CONFIG_FSL_ESDHC_ADAPTER_IDENT is no longer needed.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[Rebased, Removed T1040QDS change as board does not exist]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add xspi boot source to qixis command to let the soc boot from
flex-nor flash chip.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Remove "fdt_high" environment variable to use the bootm_size
to safely contain a kernel, device tree and initrd for
relocation.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This enables SYS_I2C_MXC to fix a bug that
failed to boot from sd card with
image u-boot-with-spl-pbl.bin
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The generic armv8 code already has support to bring up the secondary
cores. Thus, don't hardcode the jump in the layerscape lowlevel_init to
the spin table code; instead just return early and let the common armv8
code handle the jump. This way we can actually use the CPU_RELEASE_ADDR
feature.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased, Removed kontron_sl28.h change as file does not exist]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Current PFE firmware access spi-nor memory directly. New spi-mem
framework does not support direct memory access. So, let's use
spi_flash_read API to access memory instead of directly using it.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
LS1088A-RDB has MMC, SCSI, DHCP as boot targets,
but the USB support was missing.
Add support for USB as Boot_targets_devices.
Signed-off-by: Era Tiwari <era.tiwari@nxp.com>
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_FSL_LAYERSCAPE is available in kconfig. There is no need to
define it per board; the ls1028a_common.h is really board dependent and
only fits to the NXP eval boards. Instead select CONFIG_FSL_LAYERSCAPE
when ARCH_LS1028A is selected.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The Beacon EmbeddedWorks kit is based on the R8A774A1 SoC also
known as the RZ/G2M.
The kit consists of a SOM + Baseboard and supports microSD,
eMMC, Ethernet, a couple celular radios, two CAN interfaces,
Bluetooth and WiFi.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add Kconfig entries for the dc2114x driver and convert various boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Enable SPI flash(SF) distro boot command in Sifive FU540.
This distro boot will read the boot script at specific
location at the flash and start sourcing the same.
Included the SF device at the last of the target devices
list since all the rest of the devices on the list have
more possibility to boot the distribution due to the
size of the SPI flash is concern.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
HiFive-Unleashed-A00 has SPI flash with 32MiB size.
So, let's use the script offset at the end of 4K.
This way it cannot overlap any offsets being used
by software components in flash layout.
So, SF distrocmd will pick the script at desired
script address and run.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
- New rk3326 board: Hardkernel Odroid Go2;
- Update board config and dts for RockPI 4/N8/N10;
- Update led boot on support for roc-rk3399-pc;
- Enable SPI Flash suppor for rk3328 rock64 board;
- Update rockchip pcie phy to use generic framework;
Add console settings like stdin, stdout and stderr as
usbkbd and vidconsole respectively for evb-rk3288 targets.
This would certainly help to detect the attached video
devices (like HDMI) and print the console messages on display.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add default kernel_comp_addr_r and kernel_comp_size to support boot
from compressed kernel Image, this space is temporarily used during
decompress according to README.distro.
Reported-by: Tian Yuanhao <tianyuanhao@aliyun.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Also known as Odroid Go Advance but named Go2 internally by the
vendor it seems.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds very basic minimal support for the Marvell Octeon 3
CN73xx based EBB7304 EVK. Please note that the basic Octeon port does
not support DDR3/4 initialization yet. To still use U-Boot on with this
port, the L2 cache (4MiB) is used as RAM. This way, U-Boot can boot
to the prompt on this board.
Supported devices:
- UART
- reset
- CFI parallel NOR flash
Signed-off-by: Stefan Roese <sr@denx.de>
Since commit 4b0bcfa7c4 (Kconfig: Migrate CONFIG_BOOTM_* options),
the config_defaults.h file has been void of any actual content - and
these days, "sane defaults for everyone" is achieved by appropriate
default values in Kconfig. Remove it, and thus make every translation
unit process one less header file.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
All configurations have been removed in 2016 by commit 7985cdf74b
("arm64: Remove non-full-va map code").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
----------------
- i.MX DDR driver fix/update for i.MX8M
- i.MX pinctrl driver fix.
- Use arm_smccc_smc to remove imx sip function
- i.MX8M clk update
- support booting aarch32 kernel on aarch64 hardware
- fused part support for i.MX8MP
- imx6: pcm058 to DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/708734785
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXxCxWw8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76bPyACcDZ8gD9jf1P/Zh+7kqrGdIWwURF8AnAiEtNnu
FhE/WQQj4mAEWE4F2bFE
=7ceG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20200716' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
i.MX for 2020.10
----------------
- i.MX DDR driver fix/update for i.MX8M
- i.MX pinctrl driver fix.
- Use arm_smccc_smc to remove imx sip function
- i.MX8M clk update
- support booting aarch32 kernel on aarch64 hardware
- fused part support for i.MX8MP
- imx6: pcm058 to DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/708734785
Convert pcm058 support to use device trees and the driver model.
Add rudimentary boot scripts to the environment, expand README.
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
There are two options that are currently whitelisted, but they
are redundant, because there are not necessary since Kconfig options
exist to basically state the same thing.
CONFIG_DIRECT_NOR_BOOT and CONFIG_USE_NOR are both set together and
only used by the da850 when booting from NOR, however the only time
CONFIG_MTD_NOR_FLASH is configured is when booting from NOR. Since
NOR doesn't need SPL, the options for SPL can be moved to a check for
building SPL instead of checking for NOR.
This patch removes the checks for these two config options and unifies
the checks around the Kconfig option of CONFIG_MTD_NOR_FLASH.
Since this board is the only board that uses these two config options,
they can be removed from the whitelist table.
Signed-off-by: Adam Ford <aford173@gmail.com>
I actually do not see this used these days because eMMC or NAND is used
for non-volatile devices. Dump the burden to maintain this crappy code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I increased the maximum U-Boot proper size from time to time, but
configs/uniphier_v7_defconfig hit the current limit 832KB.
Some historical info:
In the initial support, the max size was 512MB.
Commit 58d702274c ("ARM: uniphier: increase CONFIG_SYS_MONITOR_LEN")
increased it to 576KB, and commit 3ce5b1a8d8 ("ARM: uniphier: move
SPL stack address") moved the SPL stack location to avoid the memory
map conflict. It was the solution to increase the size without changing
the NOR boot image map.
commit 1a4bd3a095 ("ARM: uniphier: increase CONFIG_SYS_MONITOR_LEN
again") ended up with increasing the max size again, breaking the NOR
boot image map. The limit was set to 832KB, otherwise the SPL stack
would overwrite the U-Boot proper image:
CONFIG_SPL_STACK - CONFIG_SYS_UBOOT_BASE + sizeof(struct image_header) = 0xd0000
To increase CONFIG_SYS_MONITOR_LEN even more, the SPL stack must be
moved somewhere. I put it back to the original location prior to
commit 3ce5b1a8d8.
With this change, there is no more practical size limit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
patman support for Python3 on Ubuntu 14.04
new checkpatch check to avoid #ifdefs
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl8InaQRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreazvAgAgqyvPY2o+BNHscrx9/6sEOHSAVty/D5t
SdaphzRezlJOWy9MC/ZyqyevZjogN7fgGNQVgh/I4BklIc/N5Omn68/+JWylSFVP
taJKiJD1IVSThTXGOMTxlDiTxY7NfVDUDjtFIpCDswBrnSJlX+2v/RsehUwVIrYn
NJwiRXd33IdS1vh1mqqNgwbZNBo+zGWn5LApq71vLSVkiQlmcpMG9FmYYRcg/AhG
3Xd2HB2ANcvb13fMMcwd3s4WPNYoiJvwjSHScNDUPEip7XeZNDiNeq4gC6d2Uw+J
zC3/vOCP3eRtAnr6syJ5QcGN/eeKwLtnTE+fOuOm6s5Y98po4iMykA==
=3fC5
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-10jul20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
of-platdata: better phandle and compatible-string support
patman support for Python3 on Ubuntu 14.04
new checkpatch check to avoid #ifdefs
Move ADDR_MAP related config options from include/configs/*.h to the
proper place in lib/Kconfig. This has been done using
./tools/moveconfig.py and manual inspection of the generated changes.
This is a preparation to use ADDR_MAP helper on ARM 32bit Raspberry Pi4
board for mapping the PCIe XHCI MMIO, which is above the 4GiB identity
mapping limit.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Up to now the RAM size of the sandbox is hard coded as 128 MiB. This does
not allow testing the correct handling of addresses outside the 32bit
range. 128 MiB is also rather small when tracing functions where the trace
is written to RAM.
Provide configuration variable CONFIG_SANDBOX_RAM_SIZE_MB to set the RAM
size in MiB. It defaults to 128 MiB with a minimum of 64 MiB.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
DM, OF_CONTROL, DM_SPI and other driver model migration
deadlines are expired for this board.
Remove it.
Acked-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Ash Charles <ash@gumstix.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Gilles Gameiro <gilles@gigadevices.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Drop it.
Cc: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Drop it.
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Drop it.
Cc: Ash Charles <ash@gumstix.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
DM, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
DM, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable DM_SPI, DM_SPI_FLASH for siemens draco board.
Build is fine, but not tested.
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This patch switches the SATA driver from mvsata_ide to sata_mv for the
following Kirkwood-based LaCie boards:
- d2 Network v2
- Internet Space v2
- 2Big Network v2
- Network Space v2
- Network Space Lite v2
- Network Space Max v2
- Network Space Mini v2
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The helios4 is built on the same microsom as the clearfog, by syncing the config
we enable the same featureset that exists in the som on the helios4. The current
config does not boot as some of the clearfog changes needed to be made on the
helios4 also, generally speaking most changes for the clearfog should also be
made on the helios4.
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Reviewed-by: Stefan Roese <sr@denx.de>
The arch timer on 64-bit Arm Ltd. platforms is driven by a 24 MHz
crystal oscillator, so the frequency is not 25165824 MHz, as the current
code suggests.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Now that, we calculate SDRAM size by reading DDR registers,
"CONFIG_SYS_SDRAM_SIZE" is no more needed.
This commit removes "CONFIG_SYS_SDRAM_SIZE" from common configuration
file.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Activate CMD_NVEDIT_INFO and use the new command "env info -d -p -q"
to automatically save the environment on first boot.
This patch allows to remove the env_default variable.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
In the boot command used in ST boards, bootcmd_stm32mp, only support
the SD card as second stage, where is found the bootfs with DISTRO.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Some minor fixes for SPI flash on the Pinebook Pro and also
default to saving environment to the SPI flash as it's
guaranteed to be on board.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(applied with make savedefconfig)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The built in keyboard on the Pinebook Pro is attached via USB so
fix this up to ensure USB works as expected.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Sipeed Maix series is a collection of boards built around the RISC-V
Kendryte K210 processor. This processor contains several peripherals to
accelerate neural network processing and other "ai" tasks. This includes a
"KPU" neural network processor, an audio processor supporting beamforming
reception, and a digital video port supporting capture and output at VGA
resolution. Other peripherals include 8M of sram (accessible with and
without caching); remappable pins, including 40 GPIOs; AES, FFT, and SHA256
accelerators; a DMA controller; and I2C, I2S, and SPI controllers. Maix
peripherals vary, but include spi flash; on-board usb-serial bridges; ports
for cameras, displays, and sd cards; and ESP32 chips. Currently, only the
Sipeed Maix Bit V2.0 (bitm) is supported, but the boards are fairly
similar.
Documentation for Maix boards is located at
<http://dl.sipeed.com/MAIX/HDK/>. Documentation for the Kendryte K210 is
located at <https://kendryte.com/downloads/>. However, hardware details are
rather lacking, so most technical reference has been taken from the
standalone sdk located at
<https://github.com/kendryte/kendryte-standalone-sdk>.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
-----BEGIN PGP SIGNATURE-----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=dnTK
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-06-29' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips into next
- net: pcnet: cleanup and add DM support
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
Add Kconfig entries for the pcnet driver and convert MIPS malta
to use those.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
All of one PCNET users has this option set, make this default
and drop this config option.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
This patch moves the CONFIG_DM_SPI_FLASH and CONFIG_SPI_FLASH_DATAFLASH
to be defined in Kconfig, not in board specific header file
(include/configs/<board>.h).
Before this change the CONFIG_DM_SPI_FLASH was not set in .config (so it
was not possible to use CONFIG_IS_ENABLED(DM_SPI_FLASH) in SPI DM/DTS
converted drivers), but it was set in u-boot.cfg file.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
This patch fixes issue with defining the DM_SPI_FLASH in the
configs/include/<board.h> instead of enabling this option in Kconfig.
The problem is that CONFIG_IS_ENABLED(DM_SPI_FLASH) shows false as there
is no DM_SPI_FLASH=y in .config (but the define is set in u-boot.cfg).
As a result conversion of DM_SPI_FLASH to using CONFIG_IS_ENABLED() is not
working properly.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
While in most cases CSF_SIZE is handled via Kconfig we have some i.MX8M
platforms that set the size based on the now-renamed CONFIG_SECURE_BOOT
symbol. Update things so that CSF_SIZE itself depends on IMX_HAB being
enabled and provide the default value for i.MX8M family of parts.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ye Li <ye.li@nxp.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Fixes: d714a75fd4 ("imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HAB")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Ye Li <ye.li@nxp.com>
There are two remaining users of the CONFIG_SECURE_BOOT symbol that have
not been migrated to another symbol. In this case, they should be using
CONFIG_NXP_ESBC as their guard.
Cc: Vladimir Oltean <olteanv@gmail.com>
Fixes: 5536c3c9d0 ("freescale/layerscape: Rename the config CONFIG_SECURE_BOOT name")
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CONSOLE_MUX
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_ENV
CONFIG_BOOTCOUNT_LIMIT
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AUTOBOOT_PROMPT
CONFIG_AUTOBOOT_KEYED
CONFIG_AUTOBOOT_STOP_STR
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ATMEL_NAND_HW_PMECC
CONFIG_ATMEL_NAND_HWECC
CONFIG_NAND_ATMEL
CONFIG_PMECC_CAP
CONFIG_PMECC_SECTOR_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXvScEQAKCRDKSWXLKUoM
IeHUAJ9Z1shAlbILuHZKEpqQySLHdUVgBQCff8Nf+wi1rByTrwflKt14MtIsdFY=
=2Yuu
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2020.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2020.10
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
Reduce console buffer size to 1kbyte to accommodate memory
allocations in mini u-boot for zynqmp.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
For using a debug UART on the Wandboard CONFIG_MXC_UART=y must be set in
the .config file.
To avoid duplicate definitions move the setting from
include/configs/wandboard.h to configs/wandboard_defconfig.
Document the debug UART settings in the README.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
1. Drop legacy emmcboot wrapper from env.
2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP
3. Drop DFU defines
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
1. Drop legacy emmcboot wrapper from env.
2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP
3. Drop DFU defines
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
1. Drop legacy emmcboot wrapper from env.
2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP
3. Drop DFU defines
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
1. Use distro_bootcmd as default boot command instead of
legacy emmcboot wrapper.
2. Drop emmcboot and sdboot wrappers.
3. Provide proper boot order for Distro Boot.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The distro bootscript uses kernel_image to get the file name of
the kernel, so change that variable name.
UBI boot has precedence in the default boot command. If one wants
to boot from SD with a working NAND installation stop in U-Boot
and enter:
setenv fdtfile ${soc}-colibri-${fdt_board}.dtb && run distro_bootcmd
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
When using distro boot to boot from UBI volumes the boot partition
has been hardcoded to "UBI" (capital letters). However, our default
MTD layout uses "ubi" (lower case letter). Define "ubi" as the
default UBI partition for distro boot for Toradex. This allows to
use distro boot without having to redefine the MTD partition layout
which is useful for TorizonCore.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Migration to DM_ETH is mandatory, so convert mx6cuboxi to Ethernet
Driver Model.
This also brings the benefit of restoring Ethernet functionality.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Tom Rini <trini@konsulko.com>
Migration to DM_VIDEO driver is long overdue. Update defconfigs
to enable usage of converted ipuv3 driver DM configuration.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
The ethernet PHY on all known Gen3 boards takes a while to come out
of reset, increase the auto-negotiation timeout to prevent it from
timing out in case the ethernet is used right after the board was
reset.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add Kconfig entries for the pcnet driver and convert MIPS malta
to use those.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
All of one PCNET users has this option set, make this default
and drop this config option.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Migration to DM_VIDEO driver is long overdue, configure it in
board config files. To enable the display set stdout like:
setenv stdout serial,vidconsole
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Soeren Moch <smoch@web.de>
After migration to DM 'vga' name is not longer supported,
change it to 'vidconsole' in the default environment.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
After migration to DM 'vga' name is not longer supported,
change it to 'vidconsole' in the default environment.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
After migration to DM 'vga' name is not longer supported,
change it to 'vidconsole' in the default environment.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Xiaobo Xie <xiaobo.xie@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Timur Tabi <timur@tabi.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Po Liu <po.liu@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Naveen Burmi <naveen.burmi@nxp.com>
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Ashish Kumar <ashish.kumar@nxp.com>
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
change to how sequence numbers are assigned to devices
minor fixes and improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl7kQ4kRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZrvAgAqc/TEj7QHPyW9rQSl8h65MXK93qRsnZo
4segKEtK0Rmv0S2VfmPCwujsDFl5gZUNt+rXD/l7F0a4Wzx4eYgYrEXOYsXs/ZHP
jjGrcbvO4Qkx3QzjMqqoUiQqeCgNQ9XIre8F+1NmZeQ2bFtPKbJXtXKYTcMI1wSW
PhRGbbsTnKNKC0dL0nLFG6+NC/sk6xRqMx28Ip38FTrQL+Uh67LZFpLkY3yuHo/1
CVhCw+7Aov0I6tDrdKrngjFqXRSoTsuOhavSFoW9U6llqDL7FIC6aoRo7x24lSJN
VFTRpXPmNHeslE6NHEOQs9elFpbxXR34te3k4p74rFuX/J/490UaYA==
=172C
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-12jun20' of git://git.denx.de/u-boot-dm into next
patman improvements to allow it to work with Zephyr
change to how sequence numbers are assigned to devices
minor fixes and improvements
This keeps the compatibility with the old bootcmd.
The fdtfile environment variable also needed to be set to
imx6q-tbs2910.dtb to enable booting mainline kernels
otherwise with extlinux.conf it tries to load
mx6-tbs2910.dtb instead.
With arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola
GNU/Linux distribution, we have the following size
differences:
- text: +2041 bytes
- data: 0 bytes
- bss: 0 bytes
- total: +2041 bytes
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org>
Reviewed-by: Soeren Moch <smoch@web.de>
This doesn't affect the size of the image: with
arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola GNU/Linux
distribution, the text, data, bss and total sizes remain
unchanged.
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org>
Reviewed-by: Soeren Moch <smoch@web.de>
If there are aliases for an uclass, set the base for the "dynamically"
allocated numbers next to the highest alias.
Please note, that this might lead to holes in the sequences, depending
on the device tree. For example if there is only an alias "ethernet1",
the next device seq number would be 2.
In particular this fixes a problem with boards which are using ethernet
aliases but also might have network add-in cards like the E1000. If the
board is started with the add-in card and depending on the order of the
drivers, the E1000 might occupy the first ethernet device and mess up
all the hardware addresses, because the devices are now shifted by one.
Also adapt the test cases to the new handling and add test cases
checking the holes in the seq numbers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Alex Marginean <alexandru.marginean@nxp.com>
Tested-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Michal Simek <michal.simek@xilinx.com> [on zcu102-revA]
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Acked-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Acked-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Now all boards which are using davinci SPI driver
have moved to SPL_DM so drop the unneeded non-dm code.
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
This would make SPL build to DM_SPL, SPL_OF_CONTROL.
Build fine with but not tested.
Cc: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The u-boot-spl.bin pad with ddr firmware conflicts with the
CONFIG_MALLOC_F_ADDR area, the ddr firmware will be overwritten
by malloc in SPL stage and cause ddr initialization not able
to finish. So update the related addresses to fix the issue.
Reported-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Board has flash chip on board so let store U-Boot environment there.
Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Mark the default U-Boot environment as SPI flash since
this is an on board flash device.
Updated env offset, size in contrast with default since
the U-Boot proper has to start from 384K.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This converts the following to Kconfig:
CONFIG_BZIP2
CONFIG_GZIP
CONFIG_LZO
CONFIG_ZLIB
CONFIG_LZMA
CONFIG_LZO
Signed-off-by: Tom Rini <trini@konsulko.com>
Per the boards config header file, there is no useful GPIO on these
boards. Remove CONFIG_CMD_GPIO from the defconfigs.
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
The config header for this platform disables both CMD_SF and CMD_SPI and
the defconfig leaves them enabled. Disable them from the defconfig and
enable them in the header.
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masakazu Mochizuki <masakazu.mochizuki.wd@hitachi.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The common config header for bcm7260 and bcm7445 enable
CONFIG_CMD_EXT2/EXT4 but the defconfigs do not. This results in the
commands being disabled. Enable them via the defconfig.
Cc: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The config header for this platform uses '#undef' in a number of cases.
All of the MMC related ones were already handled correctly in the
defconfig file. In the case of CONFIG_CMD_FUSE, the command was being
built and enabled via defconfig. Disable it in the defconfig, cleanup
the header.
Reviewed-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Rather than only enable CONFIG_CMD_NAND for non-SPL builds, move the CMD
options to defconfig and rework the guards to not try and call the
function in SPL builds.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The symbol "CONFIG_ARM_DCC" is used to control building
drivers/serial/arm_dcc.c. Provide a simple Kconfig entry for this.
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Tom McLeod <tom.mcleod@opalkelly.com>
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
This is a sample GPT partition layout for SD card,
right now three important partitions are added to
make the system bootable.
partition layout:
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000022 0x00000821 "loader1"
attrs: 0x0000000000000000
type: 5b193300-fc78-40cd-8002-e86c45580b47
guid: cbcbef44-e627-42bc-b134-93b6f3784b8c
2 0x00000822 0x00002821 "loader2"
attrs: 0x0000000000000000
type: 2e54b353-1271-4842-806f-e436d6af6985
guid: f54eba28-d8de-4852-978d-1a673777e2ae
3 0x00002822 0x00020821 "rootfs"
attrs: 0x0000000000000004
type: 0fc63daf-8483-4772-8e79-3d69d8477de4
type: linux
guid: 9561df46-8d55-4799-a83b-cfee9ef6ff93
Note:
- loader1 would be fsbl or spl
- loader2 would be U-Boot or U-Boot proper
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Add a support for SPL which will boot from L2 LIM (0x0800_0000) and
then SPL will boot U-Boot FIT image (OpenSBI FW_DYNAMIC + u-boot.bin)
from MMC boot devices.
SPL related code is leveraged from FSBL
(https://github.com/sifive/freedom-u540-c000-bootloader.git)
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
U-Boot has video output enabled so time to get keyboard working.
=> usb reset;usb tree
resetting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3a0000: USB OHCI 1.0
Bus usb@fe3c0000: USB EHCI 1.00
Bus usb@fe3e0000: USB OHCI 1.0
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found
scanning bus usb@fe3a0000 for devices... 1 USB Device(s) found
scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
scanning bus usb@fe3e0000 for devices... 3 USB Device(s) found
scanning bus dwc3 for devices... cannot reset port 1!?
2 USB Device(s) found
scanning usb for storage devices... 2 Storage Device(s) found
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
1 Hub (12 Mb/s, 0mA)
U-Boot Root Hub
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
1 Hub (12 Mb/s, 0mA)
| U-Boot Root Hub
|
+-2 Hub (12 Mb/s, 100mA)
| ALCOR Generic USB Hub
|
+-3 Mass Storage (12 Mb/s, 200mA)
Kingston DT 101 G2 001478544887BB3157380157
1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|
+-2 Mass Storage (5 Gb/s, 76mA)
ADATA ADATA USB Flash Drive 1520405012240002
Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Include NVME in the list of boot targets if CONFIG_NVME is enabled.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Convert the CRS305-1G-4S board to CRS3xx-98DX3236 to enable easier
implementation of new CRS3xx series boards, based on Marvell Prestera
98DX3236.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Without CONFIG_SYS_U_BOOT_OFFS set to CONFIG_SYS_SPI_U_BOOT_OFFS, U-Boot
will be located at address 0x16000. But, SPL will try to load the
payload from 0x24000 causing the boot to hang.
Signed-off-by: Ezra Buehler <ezra@easyb.ch>
Reviewed-by: Stefan Roese <sr@denx.de>
CONFIG_BZIP2 and CONFIG_GZIP_COMPRESSED are Kconfig options. Select them
by CONFIG_SANDBOX instead of setting them in configs/sandbox.h.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert CONFIG_KS8851_MLL and CONFIG_KS8851_MLL_BASEADDR to Kconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Reference to commit that adds HDMI to other rk3399 boards:
commit 9778edae55 ("rockchip: Enable HDMI output on rk3399 board w/ HDMI")
Signed-off-by: Andrius Štikonas <andrius@stikonas.eu>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Add DM_ETH support for lx2160aqds, ls2080aqds, ls1088aqds
- QSI related fixes on ls1012a, ls2080a, ls1046a, ls1088a, ls1043a based
platforms
- Bug-fixes/updtaes related to ls1046afrwy, fsl-mc, msi-map property
the mpc83xxx suvd3 variant is not longer used, so
remove it.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
ls1046afrwy does not support sata boot.
So Override default BOOT_TARGET_DEVICES
and support only mmc, usb and dhcp as boot targets.
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_SYS_MALLOC_LEN is currently set to low value and leaves very less
space to do malloc in flash environmet. Increase the value to get more
memory and also make it align with other boards(ls1046a, ls1043a etc.)
config values.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
BOOT command currently access spi-nor flash memory directly. As per spi-mem
framework, flash memory access via absolute addresses is no more possible.
Use flash APIs to access memory instead of directly using it.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
MC_INIT command currently access spi-nor flash memory directly. As per
spi-mem framework, flash memory access via absolute addresses is no more
possible. Use flash APIs to access memory instead of directly using it.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable CONFIG_SPI_FLASH_SPANSION in defconfigs of LS1046ARDB and
LS1046AQDS which have two spansion flases i.e s25fs512s each of size
64M.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Since CONFIG_FSL_QSPI is already enabled for LS1012A in defconfigs. Also
enable CONFIG_SPI_FLASH_SPANSION for LS1012A boards having spansion
flashes.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move CONFIG_FSL_QSPI to the board defconfigs and while at it also move
CONFIG_SPI_FLASH_SPANSION for LS1043AQDS.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Some of these options are not used by the driver anymore and some of
them are obsolete as the information is gathered from the dt. Also
consolidating defines in common headers.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable CONFIG_PCI_INIT_R for qemux86 and qemux86-64 pci enumeration during
boot in order to eliminate the custom preboot commands in
include/configs/qemu-x86.h.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Manage BOOT_FLASH_SPINAND, with boot_device="spi-nand"
and treat this value in bootcmd_stm32mp.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add reserve memory for OP-TEE in U-Boot and in kernel device tree:
- no more reduce the DDR size in "memory" node:
CONFIG_SYS_MEM_TOP_HIDE is no more used
- U-Boot device-tree defines the needed "reserved-memory" for OP-TEE
and U-Boot should not use this reserved memory: board_get_usable_ram_top
use lmb lib to found the first free region, the not reserved
memory, enough to relocate U-Boot: the needed size of U-Boot
is estimated with gd->mon_len + CONFIG_SYS_MALLOC_LEN.
- the optee node ("optee@...": firmware with compatible "linaro,optee-tz")
and the associated "reserved-memory" are deactivated in kernel device
tree when OP-TEE is not detected by U-Boot to prevent kernel issue
(memory is reserved but not used, optee driver probe failed).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch reduces the stm32mp1 environment size and builds
dynamically the MTD partitions with information from defconfig
(CONFIG_MTDPARTS_...).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch reduces the stm32mp1 environment size and
builds dynamically the DFU board configuration with gpt
and mtd partitions and information from defconfig
(CONFIG_DFU_ALT_RAM0).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The AV96 board does exist in multiple variants. To cater for all of
them, implement board code handling. There are two GPIOs which code
the type of the board, read them out and use the value to pick the
correct device tree from an fitImage.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: Iddb330b9a66500495885457cbe17edc0eacaaf43
After this change both device display and serial console would contain
U-Boto output automatically without any future configuration. This would
allow easier debugging on real device as access to serial console is hard
and also in qemu emulator where it is easier to copy+paste from serial
console as from SDL framebuffer.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Now when code for defining partitions is duplicated at two locations
(option CONFIG_MTDPARTS_DEFAULT in nokia_rx51_defconfig file and macro
OMAP_TAG_PARTITION_CONFIG in rx51.c file) there is no need to have common
macros. Lets inline PART* macros to rx51.c file.
Signed-off-by: Pali Rohár <pali@kernel.org>
In commit commit 43ede0bca7 ("Kconfig: Migrate MTDIDS_DEFAULT /
MTDPARTS_DEFAULT") were removed definitions for onenand partitions.
Revert them back and enable needed options for onenand support.
Signed-off-by: Pali Rohár <pali@kernel.org>
In commit commit 37304aaf60 ("Convert CONFIG_USE_PREBOOT and
CONFIG_PREBOOT to Kconfig") was moved complicated multiline script code
from C header to oneliner in defconfig. After this change multiline to wide
oneliner it is hard to read this code and even harder to debug. Moreover
this script code should be at place where are other scripts, so move it
back to C header file.
Define new env variable preboot which stores this script and in option
CONFIG_PREBOOT calls this preboot variable.
Signed-off-by: Pali Rohár <pali@kernel.org>
In commit commit 278b90ce78 ("configs: Migrate CONFIG_SYS_TEXT_BASE") was
moved definition for CONFIG_SYS_TEXT_BASE option but author probably forgot
to move also comment for lines which are moving. So do it now!
Signed-off-by: Pali Rohár <pali@kernel.org>
lpc32xx_ssp driver is deprecated, no active updates
and no board user, hence dropped the same.
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.aribaud@3adev.fr>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Beacon EmbeddedWorks, formerly known as Logic PD, is releasing
a devkit based on the i.MX8M Mini SoC consisting of baseboard +
SOM.
It supports eMMC on the SOM, microSD on the baseboard, various
GPIO, the PINCTRL, and UART.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add initial support for Technexion Pico-iMX8MQ SoM on PicoPI carrier
board. Currently working is ethernet, serial, eMMC. DT is imported
from Linux 5.4.28 ("462afcd6e7ea") .
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The env variable overlay_files is used while adding the environment
support commands for FIT loading, but it was cleaned up just prior in
commit ee53b59511 ("configs: Remove unneeded overlay_files environment
variable"). Fix this by replacing the undefined variable with the
proper name_overlays env variable.
Fixes: 76470b6929 ("configs: ti: Add environment support commands for FIT loading")
Signed-off-by: Suman Anna <s-anna@ti.com>
Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
The commit e89f8aae3d ("treewide: Migrate CONFIG_SYS_ALT_MEMTEST to Kconfig")
setup correct dependency on MEMTEST that's why there is no reason to enable
enable alternate memtest without mtest command.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no real need to exactly define space for saving patterns for
alternate memory test. It is much easier to allocate space on the stack and
use it instead of trying to find out space where pattern should be saved.
For example if you want to test the whole DDR memory you can't save patter
to DDR and you need to find it out. On Xilinx devices DDR or OCM addresses
were chosen but that means that OCM needs to be mapped and U-Boot has
access permission there.
It is easier to remove this limitation and simply save it on stack because
it is very clear that memory test can't rewrite U-Boot and U-Boot has also
full access to memory where runs from.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Move CONFIG_SYS_MTDPARTS_RUNTIME into Kconfig done by moveconfig.py.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
CONFIG_SEMIHOSTING is selected for the VFP target by the means of
Kconfig already, there is no need to check this in the header file.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Juno board features a standard compliant EHCI/OHCI USB host
controller pair, which we can just enable.
The platform data is taken from the device tree.
This allows to use USB mass storage (the only storage on a Juno r0)
for loading.
At least on my board USB seems a bit flaky, I need two "usb reset"
sequences after the "usb start" to detect an USB hard drive.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The UART base clock rate was typo-ed in the header file, probably because
the reference (the Linux .dts) was also wrong[1].
Fix the number to make the baud rate more correct.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=39a1a8941b2
Reviewed-by: Simon Glass <sjg@chromium.org>
The U-Boot documentation explains that variables ending with "_r" hold
addresses in DRAM, while those without that ending point to flash/ROM.
The default variables for the Juno board pointing to the kernel and DTB
load addresses were not complying with this scheme: they lack the
extension, but point to DRAM. This is particularly confusing since the
Juno board features parallel NOR flash, so there *is* a memory mapped
NOR address holding a DTB, for instance.
Fix the variables to use the proper names, changing initrd_addr to
ramdisk_addr_r on the way, which seems to be more prevelant and
documented. On the way adjust the FDT load address to be situated
*before* the kernel, since users happened to overwrite the DTB by the
kernel clearing its .BSS section during initialisation.
Also remove the fdt_high and initrd_high variables (which were set
to -1), to allow U-Boot moving those images around.
This should avoid many problems in the future, but breaks loading
Linux kernels < v4.2, since they expect the DTB to be loaded in the same
512MB region as the kernel. If you need to load such an old kernel,
please set fdt_high to either 0xffffffffffffffff or 0xa0000000 (if you
load the kernel to the beginning of DRAM).
That fixes loading debug kernels, which happened to overwrite the DTB on
certain setups.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Add DM model for P1010RDB
- Add I2C DM Model support for P1010RDB, T1042RDB, T2080, T4240RDB,
MPC8548CDS, T1024RDB, P4080, P3041DS, P2041RDB, P2020RDB, P1020RDB,
P5040DS
- Fix reference to READM.qe_firmware
This is part 1 of big network cleanup / DM conversion.
The dc2114x/rtl8139/pcnet/tulip PCI adapter drivers received checkpatch
cleanups in preparation for DM conversion. The smc911x is converted to
DM completely. The dwc_eth_qos cache fixes are applied.
Move CONFIG_SYS_ARM_CACHE_WRITETHROUGH and
CONFIG_SYS_ARM_CACHE_WRITEALLOC into Kconfig done by moveconfig.py.
Kconfig uses a choice between the 3 values supported in U-Boot,
including the new configuration CONFIG_SYS_ARM_CACHE_WRITEBACK
(the default configuration).
The patch also avoids to select simultaneously 2 configurations.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add initial support for Google's Coral Dev Board based on i.MX8MQ.
https://coral.ai/products/dev-board
The Phanbell naming has been used here to match the naming convention
used in Google's U-Boot source tree:
https://coral.googlesource.com/uboot-imx/
Co-developed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Tested-by: Marco Franchi <marcofrk@gmail.com>
Some of these options are not used by the driver anymore and some of them
are obsolete as the information is gathered from the dt.
So, remove the unused config options now.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
define FEC_ENET_ENABLE_TXC_DELAY to enable the delay on TXC line on
the MAC. This has to be done in order to meet RGMII specs.
According to RGMII specs the clock should get delayed so the edges of
the clock are preferrably in the middle of the edges of data-lines so
they can be sampled properly.
Our PHY expects the MAC to delay TXC line, as it is also written
in the spec. This patch makes sure the TXC delay on the FEC is enabled
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
These macros guard one switch-case statement, which grows mips malta
by some 20 bytes if debug is enabled, and even less if it is not. To
make the code simpler, just support all the NICs and be done with it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Enable SPI flash(SF) distro boot command in rk3399.
This distro boot will read the boot script at specific
location at the flash and start sourcing the same.
Included the SF device at the last of the target devices
list since all the rest of the devices on the list have
more possibility to boot the distribution due to the
size of the SPI flash is concern.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Add DM_ETH support for DPAA1, DPAA2 based RDB platforms: ls1046ardb,
ls1043ardb, lx2160ardb, ls2088ardb, ls1088ardb.
- Add GICv3 support for ls1028a, ls2088a, ls1088a.
- Add lpuart support on ls1028aqds.
- Few bug fixes and updates on ls2088a, ls1012a, ls1046a, ls1021a based
platforms.
Drop useless environment variable installer and qspi_bootcmd
for ls1012afrwy.
Only 2 MB nor flash in ls1012afrwy. So cannot get kernel(30 MB) from
the nor flash, then drop it.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
mux changes in board file to enable lpuart1 and macro
define for lpuart1 used for mux changes in board configuation
register 13
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable CONFIG_DM_ETH and CONFIG_DM_MDIO and related configs for the
LS1088ARDB board.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Most of the SPI flash devices in rockchip (rk3399)
are 16MiB size. So, let's use the script offset at
the end of 8K.
This way it cannot overlap any offsets being used
by software components in flash layout.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The default reserved memory for CMA is high memory. If LPAE is enabled,
highmem pages are non-remapped and can not be used with
dma_alloc_coherent. Reserving low memory for CMA is needed for LS1021A.
This patch appends the related CMA configuration to bootargs.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
- bmips: fix build error when disabling USB
- mips: add option to restore original exception vector base
- mips: fix off-by-one error when clearing gd_data
- mips: minor fixes for compatibility with generic SPL framework
- spl: refactor legacy image loading
- spl: add LZMA decompression support for legacy images
- Makefile: add target to build LZMA compressed U-Boot images
- mtmips: refactor and rewrite low-level init code
- mtmips: add and enable SPL support with LZMA
- mtmips: add support for MT7628 reference board
- mtmips: add support for VoCore/VoCore2 board
-----BEGIN PGP SIGNATURE-----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=2jL1
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-04-27' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips
- brcmnand: fix missing code path from Linux driver
- bmips: fix build error when disabling USB
- mips: add option to restore original exception vector base
- mips: fix off-by-one error when clearing gd_data
- mips: minor fixes for compatibility with generic SPL framework
- spl: refactor legacy image loading
- spl: add LZMA decompression support for legacy images
- Makefile: add target to build LZMA compressed U-Boot images
- mtmips: refactor and rewrite low-level init code
- mtmips: add and enable SPL support with LZMA
- mtmips: add support for MT7628 reference board
- mtmips: add support for VoCore/VoCore2 board
Small patch to add support for VoCore/VoCore2 board.
VoCore is open hardware and runs OpenWrt/LEDE.
It has WIFI, USB, UART, 20+ GPIOs but is only one inch square.
It will help you to make a smart house, study embedded system
or even make the tiniest router in the world.
Details about this SoM can be found at "https://vocore.io/v2.html".
Signed-off-by: Mauro Condarelli <mc5686@mclink.it>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch adds support for mt7628 reference board. SPL_DM and DT are not
enabled for SPL to save about 17KiB for u-boot-spl.bin.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch enables SPL for all mtmips boards. And also remove defconfig
files which are intend to build ram bootable u-boot files.
SPL_DM and OF_CONTROL are enabled for both boards.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Currently, if usb is disabled the following error is produced:
CC drivers/usb/host/ohci-hcd.o
drivers/usb/host/ohci-hcd.c: In function ‘usb_lowlevel_init’:
drivers/usb/host/ohci-hcd.c:2057:35: error: ‘CONFIG_SYS_USB_OHCI_REGS_BASE’ undeclared (first use in this function); did you mean ‘CONFIG_SYS_MONITOR_BASE’?
gohci.regs = (struct ohci_regs *)CONFIG_SYS_USB_OHCI_REGS_BASE;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
CONFIG_SYS_MONITOR_BASE
drivers/usb/host/ohci-hcd.c:2057:35: note: each undeclared identifier is reported only once for each function it appears in
drivers/usb/host/ohci-hcd.c:2061:20: error: ‘CONFIG_SYS_USB_OHCI_SLOT_NAME’ undeclared (first use in this function); did you mean ‘CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS’?
gohci.slot_name = CONFIG_SYS_USB_OHCI_SLOT_NAME;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This commit adds common arch support for Actions Semi Owl
series SoCs and removes the Bubblegum96 board files.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
FVP now loads an Android boot image named boot.img if available,
otherwise it falls back to the existing code path.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
- iproc_sdhci memory leak fix and enable R1B resp quirk
- more mmc cmds and several mmc updates from Heinirich
- Use bounce buffer for tmio sdhci
- Alignment check for tmio sdhci
Increase the malloc area size significantly to cater for bounce buffer
used by the SDHI driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Update mvebu SPL boot selection mechanism for the move to driver model
usage by ensuring that the required driver support for SPI and MMC
booting is available in SPL when the respective boot method is
selected.
Previously, all mvebu boards selected a boot method (implicitly
MVEBU_SPL_BOOT_DEVICE_SPI for many) even if SPL booting wasn't used.
This changes mvebu boot method selection to depend on SPL usage which
resolves the issue with aarch64 boards which don't use SPL getting an
implicit boot device selection resulting in unmet dependencies. The
32-bit arm boards do use SPL, but I'm led to conclude that most aren't
intentionally using the MVEBU_SPL_BOOT_DEVICE selection since none have
SPL_DM_SPI enabled in their defconfig even though they still implicitly
select the SPI boot method.
This also results in the new addition of SPL_GPIO_SUPPORT to helios4.
The mainline dts for helios4 includes the cd-gpios entry for sdhci with
identical addresses as the clearfog dts. I don't have a helios4 board
to confirm, but based on the current source conclude that the board
itself is either wired to pull the signal low for eMMC, or the default
MMC boot isn't fully functional in mainline. In either case, as far as
I can tell, including the GPIO support will at least cause no
regression.
Tested on SolidRun ClearFog devices.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix duplication resulting from merging of multiple related series.
Commits cecf38a75, bd02fd29f, and 201a500de added or adjusted SCSI
boot support for ClearFog, but in slightly different locations which
didn't result in a merge conflict.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
- Fix boot on am335x guardian board
- Increase OPSI speed on AM65x and J721E devices
- Use JTAD register for identifying K3 devices.
- Update TI entry in MAINTAINERS file.
i.MXRT1050 provides mxsfb compatible lcd controller, so let's enable
video mxsfb driver with 16bpp depth if CONFIG_DM_VIDEO is selected since
board has 16bpp only connection.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Remove 'fdt_high' and 'initrd_high' environment variables (set to 0xFFFFFFFF)
from default environment which prevents relocation of FDT and initrd.
Rely on 'bootm_size' value instead to safely relocate kernel, device tree and
initrd.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Remove 'fdt_high' and 'initrd_high' environment variables (set to 0xFFFFFFFF)
from default environment which prevents relocation of FDT and initrd.
Rely on 'bootm_size' value instead to safely relocate kernel, device tree and
initrd.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
