The iomux should have been set in board_debug_uart_init(),
do not set in board_init_f(), remove it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
TPL need dmc to init ddr sdram, and emmc, boot-order.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
evb-rk3368 is using UART2 and PX5 evb is using UART4
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
Move original spl to tpl, and add spl to load next stage firmware,
adapt all the address and option for them.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
TPL stack may different from SPL and sys stack, add support for
separate one when the board defines it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Some options like TPL_SYS_THUMB_BUILD, TPL_USE_ARCH_MEMCPY
and TPL_USE_ARCH_MEMCPY are needed for TPL build in 32bit arm.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
This is fix to:
e2a12f590d rockchip: use 'arch-rockchip' as header file path
The V2 of origin patch set has fix this, but we merge V1 by
mistake, so lets correct it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
boot0.h and gpio.h will be used by system and include by
'asm/arch/', each of them need of a copy from 'asm/arch-rockchip'.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add board code and DTs for Renesas RZ/A1 SoC-based GR-Peach,
which is a cheap development platform with RZ/A1H SoC. The
DTs are imported from Linux 5.0.11, commit d5a2675b207d .
Currently supported are UART, ethernet and RPC SPI. The board
can be booted from RPC SPI by writing the u-boot.bin binary
to the beginning of the SPI NOR, e.g. using the "sf" command.
The board can also be booted via JTAG by setting text base to
0x20020000, loading u-boot.bin there via JTAG and executing it
from that address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add platform code and DTs for Renesas RZ/A1 R7S72100 SoC.
Distinguishing feature of this SoC is that it has up to
10 MiB of on-SoC static RAM (SRAM).
The DTs are imported from Linux 5.0.11, commit d5a2675b207d .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Send CONFIG_STATUS and RECONFIG_STATUS mailbox commands to Secure
Device Manager (SDM) to get the status of FPGA and make sure the
FPGA is in user mode before enable the bridge.
Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
Software must never reset FPGA2SOC bridge. This bridge must only be
reset by POR/COLD/WARM reset. Asserting the FPGA2SOC reset by software
can cause the SoC to lock-up if there are traffics being drived into
FPGA2SOC bridge.
Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
Convert Stratix 10 SDRAM driver to device model.
Get rid of call to socfpga_per_reset() and use reset
framework.
SPL is changed from calling function in SDRAM driver
directly to just probing UCLASS_RAM.
Move sdram_s10.h from arch to driver/ddr/altera directory.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
As mx66l512 qspi flash supports quad input fast program and
quad input fast read, set spi-tx_bus-width and spi-rx_bus-width
to 4.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
As n25q128 qspi flash supports quad input fast program and
quad input fast read, set spi-tx_bus-width and spi-rx_bus-width
to 4.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
As n25q512a qspi flash supports quad input fast program and
quad input fast read, set spi-tx_bus-width and spi-rx_bus-width
to 4.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The Quad-SPI interface is able to manage up to 256Mbytes Flash
memory starting from 0x90000000 to 0x9FFFFFFF in the memory
mapped mode.
Add a dedicated MPU region into stm32_region_config.
See application note AN4760 available at www.st.com
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
for suspend/resume robustness
update value for ext_phy_ctrl_36 for suspend/resume robustness
with hardware leveling enabled.
Match recommended values from EMIF Tools app note:
http://www.ti.com/lit/an/sprac70/sprac70.pdf
Signed-off-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
In case of RTC+DDR resume, need to restore EMIF context
before initiating hardware leveling.
Signed-off-by: Brad Griffis <bgriffis@ti.com>
[j-keerthy@ti.com Fixed the am335x build issues]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Enable HW leveling in RTC+DDR path. The mandate is to enable
HW leveling bit and then wait for 1 ms before accessing any
register.
Signed-off-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Adjust DQS skew in case where invert_clkout=1 is used.
Match recommended values from EMIF Tools app note:
http://www.ti.com/lit/an/sprac70/sprac70.pdf
Signed-off-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
This fixes SPL linker script size checks for 3 lds files where the size
checks were implemented as "x < YYY_MAX_SIZE".
Fix the size checks to be "x <= YYY_MAX_SIZE" instead.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Select the PL310 UCLASS_CACHE driver for SoCFPGA.
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Find the UCLASS_CACHE driver to configure the cache controller's
settings.
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add the PL310 macros for latency control setup, read and write bits.
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
On AM654 SoC(arm64) which is IO coherent and has L3 Cache, cache
maintenance operations being done to support non-coherent platforms
causes issues.
For example, here is how U-Boot prepares/handles a buffer to receive
data from a device (DMA Write). This may vary slightly depending on the
driver framework:
Start DMA to write to destination buffer
Wait for DMA to be done (dma_receive()/dma_memcpy())
Invalidate destination buffer (invalidate_dcache_range())
Read from destination buffer
The invalidate after the DMA is needed in order to read latest data from
memory that’s updated by DMA write. Also, in case random prefetch has
pulled in buffer data during the “wait for DMA” before the DMA has
written to it. This works well for non-coherent architectures.
In case of coherent architecture with L3 cache, DMA write would directly
update L3 cache contents (assuming cacheline is present in L3) without
updating the DDR memory. So invalidate after “wait for DMA” in above
sequence would discard latest data and read will cause stale data to be
fetched from DDR. Therefore invalidate after “wait for DMA” is not
always correct on coherent architecture.
Therefore, provide a Kconfig option to disable cache maintenance ops on
coherent architectures. This has added benefit of improving the
performance of DMA transfers as we no longer need to invalidate/flush
individual cache lines(especially for buffer thats several KBs in size).
In order to facilitate use of same Kconfig across different
architecture, I have added the symbol to top level arch/Kconfig file.
Patch currently disables cache maintenance ops for arm64 only.
flush_dcache_all() and invalidate_dcache_all() are exclusively used
during enabling/disabling dcache and hence are not disabled.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
To assure the pins on R-Car Gen3 SoCs are configured correctly, always
select pin control drivers on Gen3 SoCs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
>From way back in 2015:
commit dffb86e468
Author: Masahiro Yamada <yamada.masahiro@socionext.com>
Date: Wed Aug 12 07:31:54 2015 +0900
of: flip CONFIG_SPL_DISABLE_OF_CONTROL into CONFIG_SPL_OF_CONTROL
As we discussed a couple of times, negative CONFIG options make our
life difficult; CONFIG_SYS_NO_FLASH, CONFIG_SYS_DCACHE_OFF, ...
and here is another one.
Now, there are three boards enabling OF_CONTROL on SPL:
- socfpga_arria5_defconfig
- socfpga_cyclone5_defconfig
- socfpga_socrates_defconfig
This commit adds CONFIG_SPL_OF_CONTROL for them and deletes
CONFIG_SPL_DISABLE_OF_CONTROL from the other boards to invert
the logic.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The support for DaVinci DM* SoCs has been dropped a while ago. There's
still a lot of leftover code in mach-davinci though. Entirely remove
certain files and modify the common code to no longer reference
unsupported chips.
Note: all DaVinci platforms supported in u-boot now define SOC_DA8XX
but not all define SOC_DA850 (e.g. omapl138). We can safely remove
all ifdefs for the former, but let's leave the ones for the latter.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The support for DaVinci DM* boards has been dropped a while ago. The
code for all those PHYs is no longer used and they have their own
proper PHY drivers in drivers/net/phy anyway. Remove all dead code.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
There are a few functions defined in the header file, but they are
not referenced by any Davinci code. In order to make a general
function in the future with static function declarations, this
patch will remove the references all together.
Signed-off-by: Adam Ford <aford173@gmail.com>
The card detect pin was incorrectly using IRQ_TYPE_LEVEL_LOW
instead of GPIO_ACTIVE_LOW when reading the state of the CD pin.
Without this patch, MMC1 won't be detected.
This is the same patch submitted to linux-omap, but I was hoping
to get it applied to U-Boot without having to wait for the
linux adoption and then backporting.
Fixes: 5448ff33f2 ("ARM: DTS: Resync Logic PD SOM-LV 37xx
devkit with Linux 4.18-RC4")
Signed-off-by: Adam Ford <aford173@gmail.com>
Add device-tree files from linux 5.1-rc7 needed to complete support
for PocketBeagle.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Transition to the IOPAD macros as used in Linux in which the pin mux
mode is specified using a dedicated parameter while also dropping the
related MUX_MODEx macros that are no longer needed. This transition
will allow us to keep both Linux and U-Boot DTS in sync more easily.
While at it also align the file name of the include file itself and
update any references accordingly.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
- at91sam9g20-taurus.dts: use labels
- cleanup taurus port to compile clean with
current mainline again. SPL has no serial
output anymore, so it fits into SRAM.
Signed-off-by: Heiko Schocher <hs@denx.de>
Switch from using the high priority DMSC transmit message queue used
by the secure R5 MCU island boot context to the low priority message
queue. While the change in priority is irrelevant for the current boot
architecture it however gives us access to a deeper message queue that
will allow us to buffer more messages. This is an important aspect when
sending several messages without requesting and waiting for a response
in a row which is a communication scheme used during core shutdown for
example. See AM654 TISCI User Guide for additional details.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
There is a Factory RESET button on the back side of the Turris Omnia
router. When user presses this button before powering the device up and
keeps it pressed, the microcontroller prevents the main CPU from booting
and counts how long the RESET button is being pressed (and indicates
this by lighting up front LEDs).
The idea behind this is that the user can boot the device into several
Factory RESET modes.
This patch adds support for U-Boot to read into which Factory RESET mode
the user booted the device. The value is an integer stored into the
omnia_reset environment variable. It is 0 if the button was not pressed
at all during power up, otherwise it is the number identifying the
Factory RESET mode.
This patch also changes bootcmd to a special hardcoded value if Factory
RESET button was pressed during device powerup. This special bootcmd
value sets the colors of all the LEDs on the front panel to green and
then tries to load the rescue image from the SPI flash memory and boot
it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This driver is required for Turris Omnia to read ethernet addresses.
Move the dependency from turris_omnia_defconfig to Kconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The I2C dependencies are defined in include/configs/turris_omnia.h,
because Turris Omnia won't boot correctly without I2C support.
Move these dependencies to Kconfig, so that they are selected if Turris
Omnia is selected as target.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
-----BEGIN PGP SIGNATURE-----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=CzWQ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20190426' of git://git.denx.de/u-boot-imx
Porting to DM and i.MX8
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
To avoid a warning, we need to include the header defining
back_to_bootrom for us.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
After applying the series for debug_uart_init(), Travis-CI reports:
arch/arm/mach-rockchip/rk3399/rk3399.c:90:2: error: implicit declaration of function 'spl_gpio_set_pull' [-Werror=implicit-function-declaration]
spl_gpio_set_pull(&pmugrf->gpio0_p, GPIO(BANK_B, 2), GPIO_PULL_NORMAL);
^~~~~~~~~~~~~~~~~
This is caused by a missing header-file include. Fix it.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use board_debug_uart_init() for UART iomux init instead of
do it in board_init_f, and move the function to soc file so
that we can find all the soc/board setting in soc file and
use a common board file for all rockchip SoCs later.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Prefer to use structure to access register if we could.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Move the function to soc file so
that we can find all the soc/board setting in soc file and
use a common board file later for all rockchip SoCs.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use board_debug_uart_init() for UART iomux init instead of
do it in board_init_f, and move the function to soc file so
that we can find all the soc/board setting in soc file and
use a common board file for all rockchip SoCs later.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Prefer to use structure to access register if we can.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Move the function to soc file so
that we can find all the soc/board setting in soc file and
use a common board file later for all rockchip SoCs.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Fixed up header-list to not break FASTBOOT:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use board_debug_uart_init() for UART iomux init instead of
do it in board_init_f, and move the function to soc file so
that we can find all the soc/board setting in soc file and
use a common board file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use board_debug_uart_init() for UART iomux init instead of
do it in board_init_f, and move the function to soc file so
that we can find all the soc/board setting in soc file and
use a common board file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Fixed whitespace error:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
All Rockchip SoCs use DEBUG_UART_BOARD_INIT to init per board
UART IOMUX, enable it by default.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The ARCH_SOC name default as 'rockchip' and we put all the
header file in 'arch/arm/include/asm/arch-rockchip/', but
the 'rockchip' is not the SOC name, let's correct it after
we update all the source file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsiich <philipp.tomsich@theobroma-systems.com>
Rockchip use 'arch-rockchip' instead of arch-$(SOC) as common
header file path, so that we can get the correct path directly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
rockchip platform header file is in 'arch-rockchip'
instead of arch-$(SOC) for all SoCs.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
TIMER7_BASE is no used by source code now, remove it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This failed and caused a boot failure on c201, and afaik
the pins should be setup by the new pinctrl driver.
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
u-boot,dm-pre-reloc is required for SDMMC booted rk3399 boards and
which is U-Boot specific devicetrees binding.
Move it on global rk3399-u-boot.dtsi file and rest of the U-Boot
bindings will move it future based on the requirement.
This would help to sync the devicetrees from Linux whenever required
instead of adding specific nodes.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Sync rk3399-opp.dtsi from Linux.
Linux commit details about the rk3399-opp.dtsi sync:
"arm64: dts: rockchip: use SPDX-License-Identifier"
(sha1: 4ee99cebd486238ac433da823b95cc5f8d8a6905)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Booting this board failed as the initial console isn't found since
commit c402e81702 ("dts: arm: socfpga: merge gen5 devicetrees from linux")
The uart0 devicetree entry was missing "clock-frequency = <100000000>:"
since that commit
Fixes: c402e81702 ("dts: arm: socfpga: merge gen5 devicetrees from linux")
Reported-by: rafael mello <rafaelmello_3@hotmail.com>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The usage of socfpga_sdram_apply_static_cfg() seems rather dubious and
is confirmed to lead to a rare system hang when enabling bridges. This
patch removes the socfpga_sdram_apply_static_cfg() altogether, because
it's use seems unjustified and problematic.
The socfpga_sdram_apply_static_cfg() triggers write to SDRAM staticcfg
register to set the applycfg bit, which according to old vendor U-Boot
sources can only be written when there is no traffic between the SDRAM
controller and the rest of the system. Empirical measurements confirm
this, setting the applycfg bit when there is traffic between the SDRAM
controller and CPU leads to the SDRAM controller accesses being blocked
shortly after.
Altera originally solved this by moving the entire code which sets the
staticcfg register to OCRAM [1]. The commit message claims that the
applycfg bit needs to be set after write to fpgaportrst register. This
is however inverted by Altera shortly after in [2], where the order
becomes the exact opposite of what commit message [1] claims to be the
required order. The explanation points to a possible problem in AMP
use-case, where the FPGA might be sending transactions through the F2S
bridge.
However, the AMP is only the tip of the iceberg here. Any of the other
L2, L3 or L4 masters can trigger transactions to the SDRAM. It becomes
rather non-trivial to guarantee there are no transactions to the SDRAM
controller.
The SoCFPGA SDRAM driver always writes the applycfg bit in SPL. Thus,
writing the applycfg again in bridge enable code seems redundant and
can presumably be dropped.
[1] 75905816ec
[2] 8ba6986b04
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Add optional "mask" argument to the SoCFPGA bridge command, to select
which bridges should be enabled/disabled. This allows the user to avoid
enabling bridges which are not connected into the FPGA fabric. Default
behavior is to enable/disable all bridges.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Instead of just putting the bridges into reset, fully remove the bridges
from the L3 main bridge space when disabling them by clearing bits in
NIC-301 remap register. Moreover, only touch the 3 LSbits in brgmodrst
register as the rest of the bits are undefined.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Disable bridges between L3 Main switch and FPGA unless booting
from FPGA and keep them disabled to prevent glitches and possible
hangs of the L3 Main switch.
The current version of the code could have enabled the bridges
between the L3 Main switch and FPGA for a short period of time
in board_init_f() in case the FPGA was programmed and then again
disable them at the end of board_init_f(). Replace this with a
code which only sets up the handoff registers and let the user
enable the bridges later on.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Factor out the code for programming preloader handoff register values,
the ISWGRP Handoff 0 and 1. These registers later control which bridges
are enabled by the "bridge" command on Gen5 devices.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Add the device trees for
* vexpress_ca5x2_defconfig
* vexpress_ca9x4_defconfig
* vexpress_ca15_tc2_defconfig
as available in Linux 5.1 rc5.
We are using the vexpress_ca15_tc2_defconfig and vexpress_ca9x4_defconfig
for Travis testing via QEMU.
The UEFI base Embedded Base Boot Requirements Specification (EBBR) requires
that an embedded board either provides a device tree or an ACPI table.
All block devices are meant to be moved to the driver model. On ARM this
requires a device tree.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The match controller register is not cleared during
initialization. However, some bits of this register may reset the TC if
tnMRx match it.
As we can't make any assumption about how U-Boot is launched by the first
stage bootloader (such as S1L) clearing this register ensure that the
timers work as expected.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
K3 HS devices require signed binaries for boot, use the SECDEV tools
to sign the boot artifacts during build.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
K3 devices have High Security (HS) variants along with the non-HS already
supported. Like the previous generation devices (OMAP/Keystone2) K3
supports boot chain-of-trust by authenticating and optionally decrypting
images as they are unpacked from FIT images. Add support for this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
On HS devices the 512b region of reset isolated memory called
MCU_PSRAM0 is firewalled by default. Until SYSFW is loaded we
cannot use this memory. It is only used to store a single value
left at the end of SRAM by ROM that will be needed later. Save
that value to a global variable stored in the .data section.
This section is used as .bss will be cleared between saving
this value and using it.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
- Add DM based generic watchdog start and reset implementation
and remove all ad-hoc implementations (Stefan)
- Move mv_sdhci to DM (Pierre)
- Misc turris_omnia updates (Pierre)
- Change openrd targets to correctly build again (size changes
and fixes to the dts targets) and bring it back into Travis
builds (Stefan)
- Add Kirkwood db-88f6281-bp board (Chris)
With the new generic function, the scattered other functions are now
removed to be replaced by the generic one. The new version also enables
the configuration of the watchdog timeout via the DT "timeout-sec"
property (if enabled via CONFIG_OF_CONTROL).
The watchdog servicing is enabled via CONFIG_WATCHDOG.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
This is Marvell's Kirkwood development board. It has the following
features
- 512M DDR2
- 2 PCI connectors
- 1 x1 PCI-e interface
- 1 Gigabit Ethernet Port
- 2 SATA Ports
- USB 2.0 Interface
- SDIO
- 128M NAND Flash
- 16M SPI Flash
It can be strapped to boot from SPI or NAND so there are two defconfigs
(one per boot media).
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The following Kirkwood dtb build targets are currently missing:
kirkwood-openrd-base.dtb
kirkwood-openrd-client.dtb
kirkwood-openrd-ultimate.dtb
This patch adds them to the Makefile to fix the build error.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The new DM implementation currently does not support the Sheeva
88SV331xV5 specific quirk present in the legacy implementation. The
legacy code is thus kept for this SoC and others not yet migrated to
DM_MMC.
Signed-off-by: Pierre Bourdon <delroth@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This commit switches to DM USB for warp7 and warp7_bl33 defconfigs.
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This commit switches to DM SERIAL for warp7 and warp7_bl33 defconfigs.
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Fix compatible node to use regular Toradex notation.
Annotate device tree with standard Colibri pin muxing comments.
Use open-drain I2C pin muxings.
Alphabetically re-order iomuxc nodes.
Rename snvs-ad7879-int-grp touch interrupt node as per Linux device tree.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Add GPIO1_IO03__OSC32K_32K_OUT pin muxing.
While at it also fix indentation of pinfunc header file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Sometimes we met SERROR, but only to catch it when Linux boots up.
Let's enable catching in U-Boot to catch it ealier and ease debug.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Correct CPU_ARM926EJS1 to CPU_ARM926EJS.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This patch enable convert DM MMC for imx7d-pico board and variant.
Before the DM conversion only usdhc3 was enabled and therefore it appeared
as MMC 0 to u-boot. After enabling MMC DM though usdhc3 defaults to MMC 2,
which left unattended would drive changes to existing pico-pi bootscripts and
environment variables that rely on mmc 0.
Setup the alias of mmc0 and usdhc3 so that existing pico-imx7d boot code will
work unmodified.
When converting to DM_MMC it is necessary that SPL initializes eMMC
by itself, so move the original eMMC initialization from U-Boot
proper to SPL.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Add support for lpuart1, lpuart2 and lpuart3.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Remove duplicate function declarations from the SCFW API header file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This patch imports the Linux kernel base board imx7d-pico.dtsi,
pi board imx7d-pico-pi.dts and hobbit board imx7d-pico-hobbit.dts
from Linux v5.1-rc1.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Migrate Ethernet FEC to using driver model.
Drop PHY_MICREL_KSZ90X1 which slipped in from Apalis iMX6.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate USB to using driver model.
Add USBH_PEN GPIO regulator.
While at it also add alias e.g. as required for UMS.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate MMC to using driver model.
Migrate USDHC to using pinctrl.
While at it also add GPIO1_IO03__OSC32K_32K_OUT pin muxing.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The implicit fallback mechanism for searching the whole MDIO bus for at
least one PHY has been gone with the following commit b882005a18
("drivers/net/fec: phy_init: remove redundant logic"). This lead to the
Ethernet driver erroring out as follows:
Net: Could not get PHY for FEC0: addr -19
eth-1: fec@400d1000
Colibri VFxx # dhcp
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
No ethernet found.
Could not get PHY for FEC0: addr -19
Colibri VFxx #
This commit adds an explicit PHY node which makes it work again.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This commit enables the support for K&P's HSC|DDC imx53 based boards.
It was also necessary to provide device tree description for regulators
to avoid board specific code definition.
The GPIO pin description responsible for VBUS control has been moved from
"hog" group to usbh1 dedicated one.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This code has been ported from Linux kernel - tag v5.1-rc2.
The difference from the kernel is the removal of:
fsl,usbmisc = <&usbmisc 1>;
fsl,usbphy = <&usbphy1>;
properties, which are not needed for correct u-boot operation (as PHY
setup is done in ehci-mx5.c file itself).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
In this commit the esdhc3 controller is enabled as well as it is remaped
to mmc0 to not break legacy code.
The pinctrl setup (e.g. 0x1e4) is the same as one from in-board file
definition.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
with u-boot,dm-spl added for imx8qx-pm node, and SPL_SIMPLE_BUS enabled,
the bind and probe code in board file could be removed.
Also we need to enlarge SYS_MALLOC_F_LEN to avoid calloc fail.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
A mailbox command contains 1-u32 header + arguments. The "len" variable
only contains the length of the arguments, but not the 1-u32 header.
Include the length of header when checking the ring buffer space to
prevent off-by-one error.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
By enabling debug prints in malloc_simple, we can see that SPL for socfpga
gen5 does by far not need the 8 KiB malloc pool currently allocated for
SPL in pre-reloc phase.
On socfpga_socrates, 1304 bytes are currently used (and this increases by
~200 bytes only for the sdram/reset fixes in socfpga-next).
To prevent wasting precious SRAM space, let's reduce the initial heap used
for SPL to 2 KiB. This is still some hundred bytes more than currently
used. Also, the gen5 SPL enables stack and heap in DDR memory pretty
early. Only the initial uclass/dm parsing, serial console and DDR
initialization is done in the initial heap, so these 2 KiB should be
enough for all boards.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
This commit moves common config options used in all socfpga boards
to select/imply in Kconfig. This both cleans up the defconfig files
as well as makes future changes easier.
Options implied/defaulted for all sub-arches:
- SPL, SPL_DM, USE_TINY_PRINTF, NR_DRAM_BANKS
Options implied/defaulted for implied for A10 & gen5:
- FPGA_SOCFPGA, SYS_MALLOC_F_LEN, SYS_TEXT_BASE
Options implied/defaulted for gen5:
- SPL_STACK_R, SPL_SYS_MALLOC_SIMPLE, SPL_STACK_R_ADDR
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Fixes for tracing with sandbox
Refactoring for boot_get_fdt()
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlzAfvkACgkQfxc6PpAI
reYu9AgAjaFmydXjE8DxkSB3rR7DHZFTs1erVKAAL2v+Tdf7LDmz+j6u1M3v55WY
6r54f/gZ1UX5TEmQgEAKLa7QvvRO/lNvSGQnLHhZhv2IVWo7uWCKAUPdQ6XVZnUK
zO5v+ucs9Ne4HxQJHMC509HUIIBbydiRvUm8W0SeBZy4kEyJDuub4L+rpARkXNks
IZfKuY+VS4FK73D4M9PIhoXSubZgVS4AEcapakU1DvEz0kjsN4wr4idGrp3lutPC
455imz83JBq2+mx1oxclOGedkIDzTCq+nWQAwSftMehrJpGrp7RLNo0v4QZZUf4V
LIXRqObIYse9yQLkYPpeBdePMc8/tQ==
=0NJ2
-----END PGP SIGNATURE-----
Merge tag 'pull-24apr19' of git://git.denx.de/u-boot-dm
Various minor sandbox iumprovements
Fixes for tracing with sandbox
Refactoring for boot_get_fdt()
Testing has shown that the current DM implementation of a platform /
board specific translation offset, as its needed for the SPL on MVEBU
platforms is buggy. The translation offset is confingured too late,
after the driver bind functions are run. This may result in incorrect
address translations. With the current implementation its not possible
to configure the offset earlier, as the DM code has not run at all.
This patch now removed the set_/get_translation_offset() calls and
moves the translation offset into the GD variable translation_offset.
This variable will get used when CONFIG_TRANSLATION_OFFSET is enabled.
This option is enabled only for MVEBU on ARM32 platforms, where its
currenty needed and configured in the SPL.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pierre Bourdon <delroth@gmail.com>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Tested-by: Pierre Bourdon <delroth@gmail.com>
Tested-by: Baruch Siach <baruch@tkos.co.il>
This fixes relaction isses with the PSCI_TABLE entries in
the psci_32_table and psci_64_table.
When using 32-bit adress pointers relocation was not being applied to
the tables, causing PSCI handlers to point to the un-relocated code
area. By using 64-bit data relocation is properly applied. The
handlers are thus in the "secure data" area, which is protected by
/memreserve/ in the FDT.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Add support for MediaTek MT8516 SoC. This include the file
that will initialize the SoC after boot and its device tree.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The 'phy' reset of gmac device in kernel device tree is not generic
enough for u-boot to use, so we need to overwrite the 'resets' property
as needed. With this device tree fixup and poplar_defconfig changes,
Ethernet starts working on Poplar board.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As U-boot stm32f clock driver doesn't support new
bindings for auxiliary clocks (clocks = <&rcc 1 ....>),
restore old bindings for usart1 to get console output.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Synchronize stm32h7 device tree with kernel v4.20.
U-boot DT files and pinctrl bindings are updated,
useless nodes are removed and gpio compatible added.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In order to prepare and ease future DT synchronization with kernel
DT, migrate all U-boot specific nodes/properties/addons to
U-boot DT files.
As sdmmc is not yet supported on kernel side, sdmmc nodes
are located in eval-u-boot and disco-u-boot DT files.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In order to prepare and ease future DT synchronization with kernel
DT, migrate all U-boot specific nodes/properties/addons to
U-boot DT files.
Migrate also DT nodes which are not yet available on kernel DT side
as ethernet, ltdc and qspi nodes.
Fix ethernet_mii pins and add missing qspi_pins for stm32746g-eval
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Import Linux 5.1-rc1 DT from 9e98c678c2d6 ("Linux 5.1-rc1") for the
meson-g12a-u200 board, the meson-g12a.dtsi and the corresponding bindings.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for the Amlogic G12A SoC, which is a mix between the
new physical memory mapping of AXG and the functionnalities of
the previous Amlogic GXL/GXM SoCs.
To handle the internal ethernet PHY, the Amlogic G12A SoCs now
embeds a dedicated PLL to feed the internal PHY.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add basic support for the Amlogic G12A clock controller based on
the AXG driver.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Current relocation code is limited to 21bit PC-relative addressing
which might not be enough for bigger code sizes. The following patch
increases the addressing to 32bit PC-relative. This feature is
specially interesting if U-Boot is build without optimiation (-O0) as
the text section is increased significativelly.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
HVC call makes use of 6 mandatory arguments rather than 7 in the same way
as SMC calls. The 7th argument is optional (Client ID) for both HVC and
SMC but is implemented as 16-bit parameter and register R7 or W7. The aim
of this patch is just fix compilation error due to an invalid asm code in
the HVC call so that's why the 7th argument is removed.
The issue does not report any error in a normal build as hvc_call is not
used at all and is optimized by the compiler. Using -O0 triggers the
error so the patch is intended to fix issues on a ongoing effor to build
U-Boot with -O0.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
When PSCI is enabled, we are expecting U-Boot which now act
as EL3 software will handle all the PSCI calls. We won't need
fwcall as no further HVC or SMC are needed.
Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
Allow PSCI layer to handle any SiP service functions added by
platform vendors. PSCI layer will look for SiP service function
in the SiP function table located in '._secure_svc_tbl_entries'
section if the SMC function identifier is not found in the PSCI
standard functions table. Use DECLARE_SECURE_SVC macro to declare
and add platform specific SiP service function.
This new section '._secure_svc_tbl_entries' is located next to
'._secure.text' section. Refer to arch/arm/cpu/armv8/u-boot.lds.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcvW07AAoJEB6zHgIOrC/Iu4QH/1REDOTrsZPydd2yD/O81vPs
RiLC8wP2J4UmqtMcNTLyvxlYwrzqoR5J6SYdyBNU/+cLEp/gdzEI+rjsfSV2uRX1
Qb4Pk2FiI503JVjegxsbJqzASfiEP7rIg3HM5431xbhYH22MW2FH6le6yrtNxjBh
m1WFjQYX1bpbGb6zue8TgyLIeN1IqWuqnH9kUHixUEan+xrpEhN239LDFjdvGbvC
BvYyMtDddmMt4YDzNjgX36us993kylGZp6JijR3zgUao7I/JGVZAJrxw8MHDTnVy
UKv3VI9F5bGLSvzqTVL2MFU6XtJW26v+niGLhGzlUhb3TTKrdKOicm3VF7tO+JU=
=MamK
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2019.07-b' of git://git.denx.de/u-boot-atmel
Second set of u-boot-atmel features and fixes for 2019.07 cycle
The DK1 and DK2 boards use the USB Type-C controller STUSB1600.
This patch updates:
- the device tree to add the I2C node in the DT
- the board stm32mp1 to probe this I2C device and use this controller
to check cable detection.
- the DWC2 driver to support a new dt property
"u-boot,force-b-session-valid" which forces B session and
device mode; it is a workaround because the VBUS sensing and
ID detection isn't available with stusb1600.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Use the DWC2 device driver with DM_USB_GADGET support and
cleanup the USB support in STM32MP1 board.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- 16GB eMMC
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- USB 2.0 and 3.0 Host
- HDMI port
- S/PDIF port
- 5V/2A DC power supply
- Wi-Fi/BT via Fn-Link 6222B-SRB (RTL8222BS)
Linux commit details about the sun50i-h6-beelink-gs1.dts sync:
"arm64: dts: allwinner: h6: Introduce Beelink GS1 board"
(sha1: 089bee8dd119ba084dee6b17a2e1a53df4f30193)
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The SAMA5D2 ICP Board features the SAMA5D27 SoC,
together with QSPI Flash, Wilc3000 wireless device and
EtherCat support.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Merge qspi dts node from Linux.
Commit 0cb140d07fc75fb (arm64: dts: stratix10: Add QSPI support for Stratix10)
Add -u-boot.dtsi files for non Linux dts properties and
update properties for Uboot.
- add u-boot,dm-pre-reloc
- add alias for spi0
- change compatible for flash
- support quad read and quad write
- change maximum frequency to 100MHz
Tested on Stratix 10 SoC devkit.
SOCFPGA_STRATIX10 # sf probe 0:0
SF: Detected mt25qu02g with page size 256 Bytes, erase size 64 KiB, total 256 MiB
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Scrub memory content if ECC is enabled and it is not
from warm reset boot.
Enable icache and dcache before scrub memory
and use "DC ZVA" instruction to clear memory
to zeros. This instruction writes a cache line
at a time and it can prevent false ECC error
trigger if write cache line partially.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
The stratix10 socdk ships with 4GB of memory. Modify the
device tree to represent this. Note that to access 4GB of
memory in Stratix 10, due to the IO space from 2GB to 4GB,
we use the fact that the DDR controller ignores upper address
bits outside of the configured DRAM's size. This means that
, the 4GB DRAM is mapped to memory every 4GB.
For an 8GB memory, you can either live with the 2GB IO space,
and loose access to that memory from the processor, or use
the same trick:
Loose 2GB of memory:
memory {
device_type = "memory";
/* 8GB */
/* first 2GB */
reg = <0 0x00000000 0 0x80000000>,
/* last 4GB */
<1 0x00000000 1 0x00000000>;
u-boot,dm-pre-reloc;
};
or to map it all:
memory {
device_type = "memory";
/* 8GB */
/* first 2GB */
reg = <0 0x00000000 0 0x80000000>,
/* next 6GB */
<2 0x80000000 1 0x80000000>;
u-boot,dm-pre-reloc;
};
Signed-off-by: Dalon Westergreen <dalon.westergreen@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Move SDRAM size check to SDRAM driver. sdram_calculate_size()
is called in SDRAM initialization already, avoid calling
twice in size check function.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
This commit removes ad-hoc reset handling for peripheral resets from SPL
for socfpga gen5.
This is done because as U-Boot drivers support reset handling by now.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
To clean up reset handling for socfpga gen5, port the DDR driver to DM
using UCLASS_RAM and implement proper reset handling.
This gets us rid of one ad-hoc call to socfpga_per_reset().
The gen5 driver is implemented in 2 distinct files. One of it (containing
the calibration training) is not touched much and is kept at using
hard coded addresses since the code grows even more otherwise.
SPL is changed from calling hard into the DDR driver code to just
probing UCLASS_RESET and UCLASS_RAM. It is happy after finding a RAM
driver after that.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The SPL for socfpga gen5 currently takes all peripherals out of reset
unconditionally. To implement proper reset handling for peripherals,
the reset node has to be provided with the SPL dts.
In preparation to move the DDR driver to DM, the sdr node is required
in SPL, too.
This patch adds "u-boot,dm-pre-reloc" to U-Boot specific dtsi addon
files so that the reset manager and SDR driver correctly probe in SPL.
It centralizes these settings into a common file since in contrast to
boot-type specific nodes, "soc", "rst" and "sdr" are always needed.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This is again a sync to linux-next + pending patches in Dinh's tree at
commit 1c909b2dfe6a ("ARM: dts: socfpga: update more missing reset
properties")'
It adds missing peripheral reset properties to socfpga.dtsi and removes
U-Boot specific leftovers from socfpga_cyclone5_socrates.dts.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
fpga:
- Add support for external data in FIT
- Extend testing for external data case
- Inform user about a need to run post config on Zynq
arm:
- Tune zynq command functions
- Fix internal variable setting
arm64:
- Add support for zc39dr decoding
- Disable WDT for zcu100
- Small changes in reset_reason()
- Some DT changes (spi)
- Tune qspi-mini configuration
- Remove useless eeprom setting
- Fix two sdhci boot case
spi:
- Fix tap delay programming
clk:
- Enable i2c in SPL
net:
- Fix gem phydev handling
- Remove phy detection code from gem driver
general:
- Correct EXT_DTB usage for MULTI_DTB_FIT configuration
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAly262oACgkQykllyylKDCH44gCbBnuxUH6ZF0B7Leuee4te7C59
LmUAn14/bbtMt17zkMSADCjY9yGWF4au
=mWrW
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2019.07' of git://git.denx.de/u-boot-microblaze
Xilinx/FPGA changes for v2019.07
fpga:
- Add support for external data in FIT
- Extend testing for external data case
- Inform user about a need to run post config on Zynq
arm:
- Tune zynq command functions
- Fix internal variable setting
arm64:
- Add support for zc39dr decoding
- Disable WDT for zcu100
- Small changes in reset_reason()
- Some DT changes (spi)
- Tune qspi-mini configuration
- Remove useless eeprom setting
- Fix two sdhci boot case
spi:
- Fix tap delay programming
clk:
- Enable i2c in SPL
net:
- Fix gem phydev handling
- Remove phy detection code from gem driver
general:
- Correct EXT_DTB usage for MULTI_DTB_FIT configuration
- Enable DM_MMC if MMC defined
- Enable DM_SCSI if SCSI defined
globally through Allwinner platform, the effected SoC families
and boards will make use of MMC and SCSI subsystems in driver-model.
Tested DM_MMC in one board from A64, H6, H5, H3, R40, A83T, A20, A10
SoCs.
Tested-by: Pablo Sebastián Greco <pgreco@centosproject.org> # BPI-M2-Ultra
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable ahci node for BPI-M2-Berry, this would require since
we have DM_SCSI enabled on the respective SoC.
Unable to sync the same node from Linux, since the similar change
is still in Linux ML.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable ahci node for a20-wits-pro-a20-dkt, this would require since
we have DM_SCSI enabled on the respective SoC.
Right now, ahci enabled in -u-boot.dtsi and will remove once same
supported by Linux.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable ahci node for sun7i-a20-m5.dts, this would require since
we have DM_SCSI enabled on the respective SoC.
No need to send patch to Linux for this change, since this
dts is U-Boot specific.
Cc: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Sync sun7i-a20 dts(i) files from Linux 5.1-rc2
Linux commit details about the sun7i-a20* sync:
"ARM: dts: sun7i: bananapi: Add GPIO banks regulators"
(sha1: 09c6572290f018d73ec2e812e28bada34d41815f)
Here are U-Boot specific dts changes.
- s/uart0_pins_a/uart0_pb_pins for
sun7i-a20-ainol-aw1.dts
sun7i-a20-m5.dts
sun7i-a20-primo73.dts
sun7i-a20-yones-toptech-bd1078.dts
sunxi-itead-core-common.dtsi
- s/gmac_pins_mii_a/gmac_rgmii_pins for
sun7i-a20-m5.dts
- drop i2c0, i2c1 pins from
sunxi-itead-core-common.dtsi
- drop mmc0 pins from
sun7i-a20-primo73.dts
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Sync sun8i-r40 dts(i) files from Linux 5.1-rc2
Linux commit details about the sun8i-r40* sync:
"ARM: dts: sun8i: r40: bananapi-m2-ultra: Add Bluetooth device node"
(sha1: 1e5f1db4ccd8348a21da55bff82f4263000879ef)
Linux commit details about the sun8i-v40* sync:
"ARM: dts: sunxi: Fix I2C bus warnings"
(sha1: 0729b4af5753b65aa031f58c435da53dbbf56d19)
Cc: Pablo Sebastián Greco <pgreco@centosproject.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
A missing CONFIG_ prefix while checking for this Kconfig variable makes the
check always fail. Fix it. While there also switch from the '#if defined'
form to the '#ifdef' form as the other checks in this function.
Fixes: 35e2b92344 ("arm64: zynqmp: Fix logic around CONFIG_ZYNQ_SDHCI")
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define a label for flash node so that it can be
referenced easily as required.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
spi-flash compatible string is needed for reading tx and rx bus
widths, hence add this compatible string to flash node.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
add labels to rtc, pinctrl and watchdog node.
This makes it possible to reference the nodes
from board dts files.
Signed-off-by: Heiko Schocher <hs@denx.de>
-----------
- DM support in sata
- Toradex Board to DM
- wandboard to DM
- tbs2910 to DM
- GE boards to DM
- VHybrid boards to DM
- DM_VIDEO for i.MX
-----BEGIN PGP SIGNATURE-----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=KLsH
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20190415' of git://git.denx.de/u-boot-imx
Move to DM
-----------
- DM support in sata
- Toradex Board to DM
- wandboard to DM
- tbs2910 to DM
- GE boards to DM
- VHybrid boards to DM
- DM_VIDEO for i.MX
In the aarch64 crash dump information about the loaded EFI images is added.
In README.uefi the development target is for the UEFI subsystem is
described as "Embedded Base Boot Requirements (EBBR) Specification"
compliance.
Several bug fixes are supplied.
-----BEGIN PGP SIGNATURE-----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=QdJl
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-07-rc1-2' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc1 (2)
In the aarch64 crash dump information about the loaded EFI images is added.
In README.uefi the development target is for the UEFI subsystem is
described as "Embedded Base Boot Requirements (EBBR) Specification"
compliance.
Several bug fixes are supplied.
Usually the Linux dts changes were synced in specific tags in Allwinner,
to keep track for whats been synced so-far and plan for future syncs.
But this patch sync sun50i-h6* dts(i) files from Linux w/o any specific
tag since these dts(i) changes are required for new H6 boards support.
Linux commit details about the sun50i-h6* sync:
"arm64: dts: allwinner: h6: move MMC pinctrl to dtsi"
(sha1: 6ba2e45d57afdfd982d12f168edd6a79a65075d8)
Linux commit details about the sun8i-tcon-top.h sync:
"dt-bindings: display: sunxi-drm: Add TCON TOP description"
(sha1: 59a9c39544cd1e5952c2a33028d71aa8180648f8)
Part of the sync initiated by 'Clément Péron'.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Fix broken build:
Device Tree Source is not correctly specified.
Please define 'CONFIG_DEFAULT_DEVICE_TREE'
or build with 'DEVICE_TREE=<device_tree>' argument
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix broken build:
Device Tree Source is not correctly specified.
Please define 'CONFIG_DEFAULT_DEVICE_TREE'
or build with 'DEVICE_TREE=<device_tree>' argument
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add support for Vybrid's UART2 (Colibri UART_B).
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Update device tree in preparation of further driver model migration:
Ethernet FEC, ESDHC aka MMC/SD card, I2C, NFC aka NAND flash controller,
USBH_PEN GPIO regulator.
Add iomux resp. pinctrl entries to be removed from proprietary platform
data: DSPI, ESDHC, FEC, I2C, NFC, UART, USBH_PEN GPIO.
Introduce a U-Boot specific device tree with some required
u-boot,dm-pre-reloc properties: soc, aips0, pinctrl_ddr and uart0 incl.
pinctrl.
While at it also update the MAINTAINERS file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Allow using bootaux also on VF610 aka Vybrid.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The DDR memory controller include file for the Vybrid uses
iomux_v3_cfg_t without actually including iomux-vf610.h.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Extend the driver to build with DM_VIDEO enabled. DTS files
must additionally include 'u-boot,dm-pre-reloc' property in
soc and ipu nodes to enable driver binding to ipu device.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
... as preparation for additional driver model coonversions.
We use CONFIG_OF_EMBED here to keep u-boot.imx as final binary name. So we
maintain compatibility with the original TBS u-boot and available HOWTOs
for u-boot updates.
Signed-off-by: Soeren Moch <smoch@web.de>
This code allows reusing the default u-boot as in the late board init, the
default envs are restored and proper recovery scripts executed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit brings a separate file in which the U-Boot specific
properties (like 'dm-pre-reloc') are provided.
Such approach allows easy sync with upstream Linux kernel in the
future.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This commit provides update and renames the bk4r1.dts to vf610-bk4r1.dts
file with more on SoC HW description.
The pcm052.dts has been renamed to vf610-pcm052.dts as well.
Moreover, a new vf610-pcm052.drsi file has been introduced
to reuse the common code between devices based on Phytec's
pcm052 modules.
Ported from Linux kernel - v4.20 (tag)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch allows moving vf610 based boards to a device tree and model.
Ported from Linux kernel - v4.20 (tag)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The proposed way of reading fused MAC in the imx_get_mac_from_fuse() may
be different for other boards.
This commit defines the imx_get_mac_from_fuse() as a weak function to allow
board file overriding it with customized function.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Provide function to enable I2C clocks for vf610 - in the generic code.
This function overrides the default weak function implementation (which
only returns 1).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This patch provides definitions necessary for VF610 DDR pad configurations.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
- ath79: small fixes, add support for QCA9563 SoC and AP152 reference board
- mscc: small fixes, add network support for JR2 and ServalT SoCs
- bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs
- MIPS: fix redundant relocation of initrd images
-----BEGIN PGP SIGNATURE-----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=NrV8
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-04-12' of git://git.denx.de/u-boot-mips
- mt76xx: add USB support, small fixes
- ath79: small fixes, add support for QCA9563 SoC and AP152 reference board
- mscc: small fixes, add network support for JR2 and ServalT SoCs
- bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs
- MIPS: fix redundant relocation of initrd images
If an exception occurs in a UEFI loaded image we need the start address of
the image to determine the relocation offset.
This patch adds the necessary lines after the registers in the crash dump
for armv8. A possible output would be:
UEFI image [0x00000000bffe6000:0x00000000bffe631f] pc=0x138 '/\snp.efi'
With the offset 0x138 we can now find the relevant instruction in the
disassembled 'snp.efi' binary.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- Misc dts files sync'ed with Linux version (Chris)
- Orion watchdog fix (Chris)
- kwbimage changed to also support Marvell bin_hdr binary (Chris)
- Add DM support to enable CONFIG_BLK for sata_mv (Stefan)
- Enable BLK on multiple platforms (Stefan)
- Misc minor fixes to AXP theadorable board (Stefan)
- Correct logic for DM_SCSI + unconverted drivers check (stefan)
- Misc changes to kirkwood to enable DM_USB here (Chris)
- Change ahci_mvebu to enable usage on A38x (Baruch)
- Update the kirkwood entry in git-mailrc (Baruch)
- Misc minor improvements (turris, documentation) (Baruch)
- Enhance sata_mv to support Kirkwood as well (Michael)
- Add wdt command (Michael)
- Add Marvell integrated CPUs (MSYS) support with DB-XC3-24G4XG
board support (Chris)
As no gpio.h is defined for this architecture, to avoid
a compilation failure, do not include <asm/arch/gpio.h>
for arch bcm63158.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch bcm6858.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Adds alias to set the pincontrol seq id.
For STMFX gpio expander, force sequence number after
the last bank (GPIOZ) to avoid conflict between STM32MP and STMFX
gpio bank sequence number.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add adc related nodes. These nodes are used to detect the
current supplied by USB type-C power in port on DK1 and DK2
boards.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This patch synchronizes U-boot DT with kernel one
This is based on https://patchwork.kernel.org/cover/10797115/
This patch adds initial support of STM32MP157 discovery boards:
- Add support of stm32mp157a discovery1 board (part number: STM32MP157A-DK1).
This board embeds a STM32MP157a SOC with AC package (TFBGA361, 148 ios)
and 512MB of DDR3. Several connections are available on this boards:
4*USB2.0, 1*USB2.0 typeC, SDcard, RJ45, HDMI, Arduino connector, ...
- Add support of stm32mp157c discovery2 board (part number: STM32MP157C-DK2).
This board is a "super-set" of stm32mp157a-dk1. A display panel (otm8009a)
and Murata wifi/BT combo is added.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Updates the stm32mp157c devicetree to bind the U-Boot PSCI driver need for
power off command; TF-A for stm32mp15x supports PSCI 1.0.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Activate the command poweroff by default for STM32MP1:
- with PCSI from TF-A for trusted boot
- with PMIC sysreset request for basic boot (SYSRESET_POWER)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Alignment with kernel driver name & binding
introduced by https://patchwork.kernel.org/cover/10761943/
to use the final marketing name = STPMIC1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Prepare file modification for kernel alignment and
rename driver to stpmic1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Cosmetic cleanup in mach-stm32mp Kconfig
- remove duplicated SPL_DRIVERS_MISC_SUPPORT
- update help for TARGET_STM32MP1
- set value for NR_DRAM_BANKS
- remove one comment as DEBUG_UART is deactivated by default
- include board Kconfig at the end of the file
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- export the function get_bootmode() and reused it in spl code
- manage uart instance by alias (prepare v4.19 binding)
- solve issue on nand instance
- restore console for uart boot
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Set board name with the first dts compatible found in DT
code under CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
The result with DEVICE_TREE=stm32mp157c-ev1 is:
STM32MP> env print
board=stm32mp1
board_name=stm32mp157c-ev1
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Implement checkboard() function to display
- the boot chain used: basic or trusted
- the board compatible in device tree
- the board identifier and revision, saved in OTP59 for ST boards
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
As BSEC is secure aware, all register access need to be done
by TF-A for TRUSTED boot chain, when U-Boot is executed in
normal world.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of trusted boot, using TF-A as first stage bootloader,
The boot sequence is
BootRom >=> TF-A.stm32 (clock & DDR) >=> U-Boot.stm32
The TF-A monitor provides secure monitor with support of SMC
- proprietary to manage secure devices (BSEC for example)
- PSCI for power
The same device tree is used for STMicroelectronics boards with
basic boot and with trusted boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
As per recent TRM[1], PBIAS cell on dra7 devices supports
3.3v and not 3.0v as documented earlier.
Update PBIAS regulator max voltage and the voltage written
in the driver to reflect this.
[1] http://www.ti.com/lit/pdf/sprui30
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
The ISW_ENTRY_ADDR Kconfig option under mach-omap2 isn't a SoC specific
notion but rather "where is our previous stage loaded in memory?"
option. Make use of this on ARCH_KEYSTONE rather than SPL_TEXT_BASE for
our HS builds that are not using SPL anyhow.
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com?
When initializing DDR from R5 SPL trigger U-Boot's panic facility
rather than simply returning from the board init function as there
is little point continuing code execution. Further, as panic implies
a board reset, so using it might potentially allow to recover from
this error in certain cases such as when the init failure was caused
by a temporary glitch of some sorts.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Certain parts of msmc sram can be used by DMSC or can be
marked as L3 cache. Since the available size can vary, changing
DT every time the size varies might be painful. So, query this
information using TISCI cmd and fixup the DT for kernel.
Fixing up DT does the following:
- Create a sram node if not available
- update the reg property with available size
- update ranges property
- loop through available sub nodes and delete it if:
- mentioned size is out if available range
- subnode represents l3 cache or dmsc usage.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
With the memory mapping giving us some more avialable RAM, this
updates the da850-evm-u-boot.dtsi to include the serial port, SPI
and Flash nodes along with some dependent nodes in the SPL dtb.
This also removes the platform data initialization code for the
serial port and SPI Flash.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add configuration for the MT41K128M16JT125K memory modules as used on the
Bosch Guardian device.
Based on a patch by:
Govindaraji Sivanantham <Govindaraji.Sivanantham@in.bosch.com>
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
[checkpatch.pl cleanup by Martyn Welch]
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
This patch adds dt node for DP83867 phy used on K2G ICE board and
also enable netcp device nodes for the board.
EVM hardware spec recommends to add 0.25 nsec delay in the tx
direction and 2.25 nsec delay in the rx direction for internal
delay in the clock path to be on the safer side.
The board straps RX_DV/RX_CTRL pin of on board DP83867 phy in mode
1. Unfortunately, the phy data manual disallows this. Add
ti,dp83867-rxctrl-strap-quirk in the phy node to allow software to
enable workaround suggested for this incorrect strap setting. This
ensures proper operation of this PHY.
The dts bindings are kept in sync with that from 4.14.y linux
kernel. This required the pinmux device related bindings to be
commented out to allow for compilation.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch removes the unused phy-mode property from the phy dt node. On
K2G, currently link-interface determines if phy is used or not and is
already set to use rgmii. So this is not needed. Besides phy-mode should
be added to slave interface configuration of the cpsw driver, not in the
phy node.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds a workaround to reset the phy one time during boot
using GPIO0 pin 10 to make sure, the Phy latches the configuration
from the input pins correctly.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This add pinmux configuration for rgmii interface so that network
driver can be supported on K2G ICE boards. The pinmux configurations
for this are generated using the pinmux tool at
https://dev.ti.com/pinmux/app.html#/default
As this required some BUFFER_CLASS definitions, same is re-used
from the linux defnitions in include/dt-bindings/pinctrl/keystone.h
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There is no reason not to use the Linux "jedec,spi-nor" binding in U-Boot
dts files. This compatible has been added in sf_probe, let use it.
This patch switches to jedec,spi-nor when spi-flash is used in the DTS
and DTSI files, and removed spi-flash when jedec,spi-nor is already
present.
The x86 dts are switched in a separate commit since it depends on a change
in fdtdec.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Evgeniy Paltsev <paltsev@synopsys.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Patrick Delaunay <Patrick.delaunay@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Sync armada-385-db-88f6820-amc.dts with Linux. Retain the
u-boot,dm-pre-reloc and nand differences.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This board was added to u-boot first but the Linux maintainers requested
a more descriptive name. Rename the file to match the Linux usage and
update the board defconfig.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Commit 93b283d49f ("ARM: CPU: arm926ejs: Consolidate cache routines to
common file") changed cache setup for Kirkwood such that icache_enable()
is now called from enable_caches() which is called from initr_caches()
which is in the list of functions in init_sequence_r[] prior to
arch_misc_init(). This means the call to icache_enable() in
arch_misc_init() is no longer required, so remove it.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The DB-XC3-24G4XG is a switch development board from Marvell. It can
either use and external CPU card such as the db-88f6820-amc or the
internal CPU that is integrated into the switch.
Add support for running U-Boot on the internal CPU and enable the USB,
SPI and NAND peripherals. For now this needs the bin_hdr from the
Marvell U-Boot for this board.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
One difference with the integrated CPUs is that they use a different
clock control block to the Armada devices. Update mvebu_get_nand_clock()
accordingly.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Marvell's switch chips with integrated CPUs (collectively referred to as
MSYS) share common ancestry with the Armada SoCs. Some of the IP blocks
(e.g. xor) are located at different addresses and DFX server exists as a
separate target on the MBUS (on Armada-38x it's just part of the core
complex registers).
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
We now have MEVBU boards without SPL support (e.g. db-xc3-24g4xg).
Because of this, a new compile time warning from Kconfig is show:
WARNING: unmet direct dependencies detected for SPL_OF_CONTROL
Depends on [n]: SUPPORT_OF_CONTROL [=y] && SPL [=n] && OF_CONTROL [=y]
Selected by [y]:
- ARMADA_32BIT [=y] && ARM [=y] && ARCH_MVEBU [=y]
WARNING: unmet direct dependencies detected for SPL_DM
Depends on [n]: DM [=y] && SPL [=n]
Selected by [y]:
- ARMADA_32BIT [=y] && ARM [=y] && ARCH_MVEBU [=y]
...
This patch fixes this issue and removes these warnings.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
This patch enables the PCIe port specific link capabilities configuration
for Armada XP. The weak function board_sat_r_get() was used to return
a common flag for PCIe Gen1 vs Gen2 capability for all PCIe ports. This
is now changed with this patch to return a bit per PCIe port (4 bits
in this case, bit 0 for PCIe port 0, etc).
The theadorable board uses this new feature to configure PCIe port 0
as Gen1 and all other PCIe ports as Gen2 capable. All other AXP boards
using this function are not changed in the configuration and still
configure all ports as PCIe Gen2.
This patch also removes the parameter "pex_mode" from
board_serdes_cfg_get() as this parameter was not used in any of the
implementations.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
This allows the ahci_mvebu driver to do A38x platform specific
configuration at initialization.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Now that kirkwood is using the mvebu mbus this function is no longer
needed.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The mvebu mbus code already had most of the support required for
kirkwood. The only difference is that unlike the other mvebu targets
kirkwood doesn't have a bridge control block so the code related to
managing that needs to be compiled out.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
KW_DEFADR_PCI_IO_REMAP has the same value as KW_DEFADR_PCI_IO and is
only used to set up a 1:1 mapping. Remove it and update the mapping to
use KW_DEFADR_PCI_IO.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This will allow the kirkwood platforms to use more common code with the
other mvebu SoCs.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable the hardware watchdog to guard against system lock ups when
running in the SPL or U-Boot. Stop the watchdog just before booting so
that the OS can re-enable it if needed.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Bring in the Armada 370/XP dts/dtsi files from Linux. As U-Boot hasn't
got the new NAND driver the updating binding has not been included.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add DT node for MCU NAVSS its components to get DMA working on AM654
SoC.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Merge drivers/soc/keystone/ into drivers/soc/ti/
and convert CONFIG_TI_KEYSTONE_SERDES into Kconfig.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Texas Instruments' System Control Interface (TI-SCI) Message Protocol
abstracts management of NAVSS resources, like PSI-L pairing and
unpairing, UDMAP tx/rx/flow configuration and Rings.
This patch adds support for requesting and configuring such resources
from TI-SCI firmware.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Import Linux 5.0 DT from 1c163f4c7b3f ("Linux 5.0") for the
meson-gxl-s805x-libretech-ac board and the corresponding changes
in meson-gxl.dtsi.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Amlogic SoCs have a registers containing the die revision
and packaging type to determine the SoC family and package marketing
name like S905X for the GXL SoC Family.
This code is taken from the Linux meson-gx-socinfo driver and adapted
to U-Boot printing.
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: also updated new p200/p201 defconfigs]
This adds *-u-boot.dtsi files for p200 and p201 boards
These are just copies of arch/arm/dts/meson-gxbb-odroidc2-u-boot.dtsi
Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds the device trees for p200 and p201 boards.
Synced from kernel 5.0.0
Commit: a667cb7a94d4 ("Merge branch 'akpm' (patches from Andrew)")
Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
