OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Ash Charles <ash@gumstix.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Gilles Gameiro <gilles@gigadevices.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Drop it.
Cc: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Drop it.
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Drop it.
Cc: Ash Charles <ash@gumstix.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
DM, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
DM, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable DM_SPI, DM_SPI_FLASH for siemens draco board.
Build is fine, but not tested.
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
- Add two- and three-argument versions of CONFIG_IS_ENABLED in
linux/kconfig.h
- Adds a new feature which supports copying modified parts of
the frame buffer to the uncached hardware buffer
- Enable the copy framebuffer on various x86 targets
Some PCI Express register offsets are currently defined in multiple
drivers, move them to a common header to avoid re-definitions and
as a pre-requisite for adding new PCIe driver.
While at it replace some spaces with tabs.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
There might be hardware configurations where 64-bit data accesses
to XHCI registers are not supported properly. This patch removes
the readq/writeq so always two 32-bit accesses are used to read/write
64-bit XHCI registers, similarly as it is done in Linux kernel.
This patch fixes operation of the XHCI controller on RPI4 Broadcom
BCM2711 SoC based board, where the VL805 USB XHCI controller is
connected to the PCIe Root Complex, which is attached to the system
through the SCB bridge.
Even though the architecture is 64-bit the PCIe BAR is 32-bit and likely
the 64-bit wide register accesses initiated by the CPU are not properly
translated to a sequence of 32-bit PCIe accesses.
xhci_readq(), for example, always returns same value in upper and lower
32-bits, e.g. 0xabcd1234abcd1234 instead of 0x00000000abcd1234.
Cc: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
i2c changes for v2020.10
- Add support for I2C controllers found on Octeon II/III and Octeon TX
TX2 SoC platforms.
- Add I2C controller support for Cortina Access CAxxxx SoCs
- new rtc methods, rtc command, and tests
- imx_lpi2c: Improve the codes to use private data
- stm32f7_i2c.c: Add new compatible "st,stm32mp15-i2c"
- stm32f7_i2c.c: Add Fast Mode Plus support
- pwm: Add PWM driver for SiFive SoC
This patch switches the SATA driver from mvsata_ide to sata_mv for the
following Kirkwood-based LaCie boards:
- d2 Network v2
- Internet Space v2
- 2Big Network v2
- Network Space v2
- Network Space Lite v2
- Network Space Max v2
- Network Space Mini v2
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The helios4 is built on the same microsom as the clearfog, by syncing the config
we enable the same featureset that exists in the som on the helios4. The current
config does not boot as some of the clearfog changes needed to be made on the
helios4 also, generally speaking most changes for the clearfog should also be
made on the helios4.
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Reviewed-by: Stefan Roese <sr@denx.de>
These prevent use of compile-time checks such as:
if (CONFIG_IS_ENABLED(DM_SPI))
since, for example, if CONFIG_SPL_DM_SPI is not enabled then the
definitions are not included by spi.h and the C code will not build.
The #ifdefs are unnecessary since there are no conflicts with the pre-DM
code. In any case we have almost switched over to driver model for SPI.
Drop these #ifdefs from spi.h to fix a build warning on chromebook_coral
in the following patch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This adds a bunch of preprocessor magic to extend the capabilities of
CONFIG_IS_ENABLED. The existing semantics of
CONFIG_IS_ENABLED(FOO)
expanding to a 1 or 0 (depending on build context and the defined-ness
or not of the appropriate CONFIG_FOO/CONFIG_SPL_FOO/CONFIG_TPL_FOO)
are of course preserved. With this, one is also allowed a two-argument
form
CONFIG_IS_ENABLED(FOO, (something))
which expands to something precisely when CONFIG_IS_ENABLED(FOO) would
expand to 1, and expands to nothing otherwise. It is, in other words,
completely equivalent to the three lines
#if CONFIG_IS_ENABLED(FOO)
something
#endif
The second argument must be parenthesized in order to allow any
tokens, including a trailing comma, to appear - one use case for this
is precisely to make it a bit more ergonomic to build an array and
only include certain items depending on .config. That should increase
both readability and not least "git grep"ability.
A third variant is also introduced,
CONFIG_IS_ENABLED(FOO, (xxx), (yyy))
which corresponds to
#if CONFIG_IS_ENABLED(FOO)
xxx
#else
yyy
#endif
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
U-Boot does not have loadable modules, and nothing currently uses any
of the (CONFIG_)?IS_(BUILTIN|MODULE) macros - only
the (CONFIG_)?IS_ENABLED variants are ever used.
While I understand the desire to keep this somewhat synchronized with
linux, we've already departed by the introduction of the
CONFIG_IS_ENABLED extra logic, and deleting these makes the next patch
much simpler, since I won't have to duplicate a lot of logic for no
real gain (as there are no users).
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Instead of using the arg1_or_junk trick to pick between two choices,
with a bit of duplication between the branches (and most of the
CONFIG_TPL_BUILD case being redundant, as _IS_TPL is known to be
defined to 1 in that case), simply define a prefix that we inject
between CONFIG_ and the given config symbol.
This only requires one level of indirection (to get the
_CONFIG_PREFIX macro expanded before the token concatenation takes
place), and makes it easy to, say, introduce a CONFIG_HOSTTOOL_
prefix. [I would expect most HOSTTOOL_ symbols to just be def_bool y,
but it would allow us to clean up some of the ifdef HOSTCC mess in the
sources shared between U-Boot and host tools.]
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This struct is not commented but needs it. Also fix the comment in
check_vidconsole_output() about the encoding for the rotation value.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Add a convenience function to call video_sync_copy() for a vidconsole.
Also add a memmove() helper, which does the memmove() as well as the sync.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Some architectures use a cached framebuffer and flush the cache as needed
so that changes are visible. This is supported by U-Boot.
However x86 uses an uncached framebuffer with a 'write-combining' feature
to speed up writes. Reads are permitted but they are extremely expensive.
Unfortunately, reading from the frame buffer is quite common, e.g. to
scroll it. This makes scrolling very slow.
Add a new feature which supports copying modified parts of the frame
buffer to the uncached hardware buffer. This speeds up scrolling by at
least 10x on x86 so the extra complexity cost seems worth it.
As a starting point, add the Kconfig, update the video structures to keep
track of the buffer and add a function to do the copy.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Add a few notes to explain the purpose of each member of this struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
All of the functions in this file only apply if DM_VIDEO is enabled. Drop
the #ifdef as it just clutters things up. Add the needed forward
declaration.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In the video drivers it is useful to print errors while debugging but
doing so risks an infinite loop as the debugging info itself may go
through the video drivers.
Add a new console function that prints information only to the serial
device, thus making it safe for use in debugging.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Similar to dm_rtc_read(), introduce a helper that allows the caller to
write multiple consecutive 8-bit registers with one call. If the
driver provides the ->write method, use that, otherwise loop using
->write8.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Some users may want to read multiple consecutive 8-bit
registers. Instead of each caller having to implement the loop,
provide a dm_rtc_read() helper. Also, allow a driver to provide a
->read method, which can be more efficient than reading one register
at a time.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
rsa_verify() expects a memory region and wants to do the hashing itself,
but there may be cases where the hashing is done via other means,
like hashing a squashfs rootfs.
So add rsa_verify_hash() to allow verifiying a signature against
an existing hash. As this entails the same verification routines
we can just move the relevant code over from rsa_verify() and also
call rsa_verify_hash() from there.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Define this macro always so we don't need the preprocessor to check it.
Convert the users to #if instead of #ifdef.
Note that '#if MEM_SUPPORT_64BIT_DATA' does not give an error if the
macro is not define. It just assumes zero.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The offset at which the image to be loaded from NAND is located is
retrieved from the itb header. The presence of bad blocks in the area
of the NAND where the itb image is located could invalidate the offset
which must therefore be adjusted taking into account the state of the
sectors concerned.
cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Add linefeeds before and after the announce string. This makes the
output easier to read, especially if some text follows the announce
message without a specific additional CR.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The arch timer on 64-bit Arm Ltd. platforms is driven by a 24 MHz
crystal oscillator, so the frequency is not 25165824 MHz, as the current
code suggests.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Now that, we calculate SDRAM size by reading DDR registers,
"CONFIG_SYS_SDRAM_SIZE" is no more needed.
This commit removes "CONFIG_SYS_SDRAM_SIZE" from common configuration
file.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This patch adds support for ZSTD decompression of FIT images.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Renamed dm "drivers" subcommand to "compat" (as it listed
compatibility strings) and prevent it from segfaulting when
drivers have no of_match populated.
Added a new "drivers" subcommand to dump a list of all known DM
drivers and for each, their uclass id, uclass driver and names of
attached devices.
Added a new "static" subcommand to dump a list of DM drivers with
statically defined platform data.
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added command "fstypes" to list supported/included filesystems.
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Limit to sandbox]
Signed-off-by: Tom Rini <trini@konsulko.com>
Activate CMD_NVEDIT_INFO and use the new command "env info -d -p -q"
to automatically save the environment on first boot.
This patch allows to remove the env_default variable.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
In the boot command used in ST boards, bootcmd_stm32mp, only support
the SD card as second stage, where is found the bootfs with DISTRO.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Some minor fixes for SPI flash on the Pinebook Pro and also
default to saving environment to the SPI flash as it's
guaranteed to be on board.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(applied with make savedefconfig)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The built in keyboard on the Pinebook Pro is attached via USB so
fix this up to ensure USB works as expected.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This series comprises error corrections for the UEFI subsystem:
* correct consideration of timestamps for variable authentication
* correct collection of data regions for code authentication
* correct unit tests to test loading dbx
* enable FAT_WRITE as required by the UEFI spec
The boot manager uses log functions instead of printf() and debug().
The UEFI intialization state is exported.
-----BEGIN PGP SIGNATURE-----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=wwI2
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-10-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi into next
Pull request for UEFI sub-system for efi-2020-10-rc1
This series comprises error corrections for the UEFI subsystem:
* correct consideration of timestamps for variable authentication
* correct collection of data regions for code authentication
* correct unit tests to test loading dbx
* enable FAT_WRITE as required by the UEFI spec
The boot manager uses log functions instead of printf() and debug().
The UEFI intialization state is exported.
- Resync Kconfiglib with the v14.1.0 release.
- Re-sync our <linux/compiler*h> files with v5.7-rc5 from upstream.
- Fully resync checkpatch.pl with v5.7 release.
To safely to all of the above, we have a few bugfixes about functions
that need a 'static inline' but weren't. We also stop setting
CROSS_COMPILE in arch/*/config.mk. Finally, with the above changes
boards can now opt-in to optimizing inlining and we do this for the
socfpga stratix10 platform for space savings.
Export the UEFI sub-system initialization state. This will allow to treat
the setting of UEFI variables during and after initialization differently.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
There are cases where when we allow the compiler to decide about making
inline decisions rather than forcing them it can save us space.
For now, we keep the default values for inlining that we have had
historically.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
In the Linux kernel, support for forcing inline functions to be made
inline, rather than allowing the compiler to make its own choice has
been removed. With respect to performance, modern GCC (and Clang) do a
good job at deciding when to, or not to, inline code and there are no
run-time requirements in Linux anymore.
There is one downside to this, which is final binary size. On average
in U-Boot removing this support grows SPL by almost 1 kilobyte. But
there are cases where it shrinks the binary by making better inline
choices than we had forced.
Start by re-introducing CONFIG_OPTIMIZE_INLINING as a global which
essentially reverts 889b3c1245de ("compiler: remove CONFIG_OPTIMIZE_INLINING entirely")
from Linux.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Copy these from Linux v5.7-rc5 tag.
This brings in some handy new attributes and is otherwise important to
keep in sync.
We drop the reference to smp_read_barrier_depends() as it is not
relevant on the architectures we support at this time, based on where
it's implemented in Linux today. We drop the call to kasan_check_read()
as that is not relevant to U-Boot as well.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The Sipeed Maix series is a collection of boards built around the RISC-V
Kendryte K210 processor. This processor contains several peripherals to
accelerate neural network processing and other "ai" tasks. This includes a
"KPU" neural network processor, an audio processor supporting beamforming
reception, and a digital video port supporting capture and output at VGA
resolution. Other peripherals include 8M of sram (accessible with and
without caching); remappable pins, including 40 GPIOs; AES, FFT, and SHA256
accelerators; a DMA controller; and I2C, I2S, and SPI controllers. Maix
peripherals vary, but include spi flash; on-board usb-serial bridges; ports
for cameras, displays, and sd cards; and ESP32 chips. Currently, only the
Sipeed Maix Bit V2.0 (bitm) is supported, but the boards are fairly
similar.
Documentation for Maix boards is located at
<http://dl.sipeed.com/MAIX/HDK/>. Documentation for the Kendryte K210 is
located at <https://kendryte.com/downloads/>. However, hardware details are
rather lacking, so most technical reference has been taken from the
standalone sdk located at
<https://github.com/kendryte/kendryte-standalone-sdk>.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Where possible, I have tried to find compatible drivers based on the layout
of registers. However, many devices remain untested. All untested devices
have been left disabled, but some tentative properties (such as compatible
strings, and clocks, interrupts, and resets properties) have been added.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
dev_read_addr_ptr had different semantics depending on whether OF_LIVE was
enabled. This patch converts both implementations to return NULL on error,
and converts all call sites which check for FDT_ADDR_T_NONE to check for
NULL instead. This patch also removes the call to map_physmem, since we
have dev_remap_addr* for those semantics.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Due to the large number of clocks, I decided to use the CCF. The overall
structure is modeled after the imx code. Clocks parameters are stored in
several arrays, and are then instantiated at run-time. There are some
translation macros (FOOIFY()) which allow for more dense packing.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
CC: Lukasz Majewski <lukma@denx.de>
This is a small driver to do a software bypass of a clock if hardware
bypass is not working. I have tried to write this in a generic fashion, so
that it could be potentially broken out of the kendryte code at some future
date. For the K210, it is used to have aclk bypass pll0 and use in0 instead
so that the CPU keeps on working.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
CC: Lukasz Majewski <lukma@denx.de>
This pll code is primarily based on the code from the kendryte standalone
sdk in lib/drivers/sysctl.c. k210_pll_calc_config is roughly analogous to
the algorithm used to set the pll frequency, but it has been completely
rewritten to be fixed-point based.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
CC: Lukasz Majewski <lukma@denx.de>
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
-----BEGIN PGP SIGNATURE-----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=dnTK
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-06-29' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips into next
- net: pcnet: cleanup and add DM support
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
Clean-up platform data include file by using BIT macro and converting
indentation with spaces to tabs.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Add Kconfig entries for the pcnet driver and convert MIPS malta
to use those.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
All of one PCNET users has this option set, make this default
and drop this config option.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
This patch moves the CONFIG_DM_SPI_FLASH and CONFIG_SPI_FLASH_DATAFLASH
to be defined in Kconfig, not in board specific header file
(include/configs/<board>.h).
Before this change the CONFIG_DM_SPI_FLASH was not set in .config (so it
was not possible to use CONFIG_IS_ENABLED(DM_SPI_FLASH) in SPI DM/DTS
converted drivers), but it was set in u-boot.cfg file.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
This patch fixes issue with defining the DM_SPI_FLASH in the
configs/include/<board.h> instead of enabling this option in Kconfig.
The problem is that CONFIG_IS_ENABLED(DM_SPI_FLASH) shows false as there
is no DM_SPI_FLASH=y in .config (but the define is set in u-boot.cfg).
As a result conversion of DM_SPI_FLASH to using CONFIG_IS_ENABLED() is not
working properly.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
This change allows more fine tuning of driver model based SPI support in
SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI
support in SPL and TPL via Kconfig option.
Before this change it was necessary to use:
/* SPI Flash Configs */
#if defined(CONFIG_SPL_BUILD)
#undef CONFIG_DM_SPI
#undef CONFIG_DM_SPI_FLASH
#undef CONFIG_SPI_FLASH_MTD
#endif
in the ./include/configs/<board>.h, which is error prone and shall be
avoided when we strive to switch to Kconfig.
The goal of this patch:
Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL).
Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must
still support non DM driver.
Another use case is the conversion of non DM/DTS SPI driver to support
DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the
distinction is needed in Kconfig (also if SPL version of the driver
supports OF_PLATDATA).
In the end of the day one would have to support following use cases (in
single driver file - e.g. mxs_spi.c):
- U-Boot proper driver supporting DT/DTS
- U-Boot proper driver without DT/DTS support (deprecated)
- SPL driver without DT/DTS support
- SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to
run full blown DT/DTS)
- SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained
environment with no fitImage and OF_LIBFDT support).
Some boards do require SPI support (with DM) in SPL (TPL) and some only
have DM_SPI{_FLASH} defined to allow compiling SPL.
This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI)
and provides corresponding defines in Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[trini: Fixup a few platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
- fix banner string overwriting the logo on small displays
- fix splash warning when building for ARM64
- fix STM32 DSI driver to probe only on supported hardware
- fix memory corruption with DSI panel drivers
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXviLYw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXDKoAJ9c+Rcel2q/lM8lK4NkhVLIdOfFxgCffcy4laCM
A1Hk+Ru0PQ77dhlI684=
=g+Hg
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v2020.07' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- fix logo on mx6ul_14x14_evk with DM_VIDEO enabled
- fix banner string overwriting the logo on small displays
- fix splash warning when building for ARM64
- fix STM32 DSI driver to probe only on supported hardware
- fix memory corruption with DSI panel drivers
Add new fields "lanes, format & mode_flags" to structure
mipi_dsi_panel_plat.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
While in most cases CSF_SIZE is handled via Kconfig we have some i.MX8M
platforms that set the size based on the now-renamed CONFIG_SECURE_BOOT
symbol. Update things so that CSF_SIZE itself depends on IMX_HAB being
enabled and provide the default value for i.MX8M family of parts.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ye Li <ye.li@nxp.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Fixes: d714a75fd4 ("imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HAB")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Ye Li <ye.li@nxp.com>
There are two remaining users of the CONFIG_SECURE_BOOT symbol that have
not been migrated to another symbol. In this case, they should be using
CONFIG_NXP_ESBC as their guard.
Cc: Vladimir Oltean <olteanv@gmail.com>
Fixes: 5536c3c9d0 ("freescale/layerscape: Rename the config CONFIG_SECURE_BOOT name")
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CONSOLE_MUX
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_ENV
CONFIG_BOOTCOUNT_LIMIT
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AUTOBOOT_PROMPT
CONFIG_AUTOBOOT_KEYED
CONFIG_AUTOBOOT_STOP_STR
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ATMEL_NAND_HW_PMECC
CONFIG_ATMEL_NAND_HWECC
CONFIG_NAND_ATMEL
CONFIG_PMECC_CAP
CONFIG_PMECC_SECTOR_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
We don't really want to have ARM-specific code in a generic file. Create
a new arch-specific function to hold it, and move it into that.
Make the function weak so that any arch can implement it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the functions to print a number and a frequency are static. We
want to move some of the code in here to an arch-specific file. For
consistency that code should use these same functions. So export them with
an appropriate name.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These values were 'old' in 2013 so it should be safe to remove them. They
are never set in U-Boot anyway, so the values will always be zero.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXvScEQAKCRDKSWXLKUoM
IeHUAJ9Z1shAlbILuHZKEpqQySLHdUVgBQCff8Nf+wi1rByTrwflKt14MtIsdFY=
=2Yuu
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2020.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2020.10
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
Reduce console buffer size to 1kbyte to accommodate memory
allocations in mini u-boot for zynqmp.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Correct the PL bitstream loading sequence for zynqaes command by
clearing the loaded PL bitstream before loading the new encrypted
bitstream using the zynq aes command. This was done by setting
the PROG_B same as in case of fpgaload commands.
This patch fixes the issue of loading the encrypted PL bitstream
onto the PL in which a bitstream has already been loaded
successfully.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In current code, we add 1ms dealy after each tuning command for standard
tuning method. Adding this 1ms dealy is because USDHC default check the
CMD CRC and DATA line. If detect the CMD CRC, USDHC standard tuning
IC logic do not wait for the tuning data sending out by the card, trigger
the buffer read ready interrupt immediately, and step to next cycle. So
when next time the new tuning command send out by USDHC, card may still
not send out the tuning data of the upper command,then some eMMC cards
may stuck, can't response to any command, block the whole tuning procedure.
If do not check the CMD CRC for tuning, then do not has this issue. USDHC
will wait for the tuning data of each tuning command and check them. If the
tuning data pass the check, it also means the CMD line also okay for tuning.
So this patch disable the CMD CRC check for tuning, save some time for the
whole tuning procedure.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
According the RM, the bit[6~0] of register ESDHC_TUNING_CTRL is
TUNING_START_TAP, bit[7] of this register is to disable the command
CRC check for standard tuning. So fix it here.
Fixes: fa33d20749 ("mmc: split fsl_esdhc driver for i.MX")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Commit 0528979fa7 ("part: Drop disk_partition_t typedef") changed to
a struct. As a result it uncovered an apparent missing include in
zfs_common.h for part.h which actually contains the definition. The ZFS
handles the struct exclusively as pointers so it was only a warning.
warning: ‘struct disk_partition’ declared inside parameter list
will not be visible outside of this definition or declaration
void zfs_set_blk_dev(struct blk_desc *rbdd, struct disk_partition *info);
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Series-CC: Simon Glass <sjg@chromium.org>
For using a debug UART on the Wandboard CONFIG_MXC_UART=y must be set in
the .config file.
To avoid duplicate definitions move the setting from
include/configs/wandboard.h to configs/wandboard_defconfig.
Document the debug UART settings in the README.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
1. Drop legacy emmcboot wrapper from env.
2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP
3. Drop DFU defines
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
1. Drop legacy emmcboot wrapper from env.
2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP
3. Drop DFU defines
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
1. Drop legacy emmcboot wrapper from env.
2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP
3. Drop DFU defines
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
1. Use distro_bootcmd as default boot command instead of
legacy emmcboot wrapper.
2. Drop emmcboot and sdboot wrappers.
3. Provide proper boot order for Distro Boot.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The distro bootscript uses kernel_image to get the file name of
the kernel, so change that variable name.
UBI boot has precedence in the default boot command. If one wants
to boot from SD with a working NAND installation stop in U-Boot
and enter:
setenv fdtfile ${soc}-colibri-${fdt_board}.dtb && run distro_bootcmd
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
When using distro boot to boot from UBI volumes the boot partition
has been hardcoded to "UBI" (capital letters). However, our default
MTD layout uses "ubi" (lower case letter). Define "ubi" as the
default UBI partition for distro boot for Toradex. This allows to
use distro boot without having to redefine the MTD partition layout
which is useful for TorizonCore.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Migration to DM_ETH is mandatory, so convert mx6cuboxi to Ethernet
Driver Model.
This also brings the benefit of restoring Ethernet functionality.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Tom Rini <trini@konsulko.com>
- use 'vidconsole' stdout in nitrogen6x upgrade script
- add option for selection of the vidconsole commands
lcdputs and setcurs
- allow building ipuv3 driver with disabled CONFIG_PANEL
- make backlight and panel drivers optional
- remove useless code from ipuv3 driver
- extend existing DM_VIDEO work-around for console name
to support 'vga'
- remove non-DM code in ipuv3
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXuvRkA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXMpeAJkB/FzsJ3O7putHrbLKOrLRF3zZYwCfQxa9jKuh
DXNTYVrHS/43T8ijGYo=
=7G75
-----END PGP SIGNATURE-----
Merge tag 'video-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-video into next
- migrate remaining imx5/imx6qd boards to DM_VIDEO
- use 'vidconsole' stdout in nitrogen6x upgrade script
- add option for selection of the vidconsole commands
lcdputs and setcurs
- allow building ipuv3 driver with disabled CONFIG_PANEL
- make backlight and panel drivers optional
- remove useless code from ipuv3 driver
- extend existing DM_VIDEO work-around for console name
to support 'vga'
- remove non-DM code in ipuv3
Migration to DM_VIDEO driver is long overdue. Update defconfigs
to enable usage of converted ipuv3 driver DM configuration.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
The ethernet PHY on all known Gen3 boards takes a while to come out
of reset, increase the auto-negotiation timeout to prevent it from
timing out in case the ethernet is used right after the board was
reset.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add Kconfig entries for the pcnet driver and convert MIPS malta
to use those.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
All of one PCNET users has this option set, make this default
and drop this config option.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Migration to DM_VIDEO driver is long overdue, configure it in
board config files. To enable the display set stdout like:
setenv stdout serial,vidconsole
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Soeren Moch <smoch@web.de>
After migration to DM 'vga' name is not longer supported,
change it to 'vidconsole' in the default environment.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
After migration to DM 'vga' name is not longer supported,
change it to 'vidconsole' in the default environment.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
After migration to DM 'vga' name is not longer supported,
change it to 'vidconsole' in the default environment.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Modify the Freescale ESPI driver to support the driver model.
Also resolved the following problems:
===================== WARNING ======================
This board does not use CONFIG_DM_SPI. Please update
the board before v2019.04 for no dm conversion
and v2019.07 for partially dm converted drivers.
Failure to update can lead to driver/board removal
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_SPI_FLASH. Please update
the board to use CONFIG_SPI_FLASH before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Xiaobo Xie <xiaobo.xie@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Timur Tabi <timur@tabi.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Po Liu <po.liu@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Naveen Burmi <naveen.burmi@nxp.com>
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Ashish Kumar <ashish.kumar@nxp.com>
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Use correct printf code in efi_image_parse().
Add random number generation to HTML documentation.
-----BEGIN PGP SIGNATURE-----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=yON/
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-07-rc5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc5
Use correct printf code in efi_image_parse().
Add random number generation to HTML documentation.
When eSDHC operates at 3.3v, damage can accumulate in an internal
level shifter at a higher than expected rate. The faster the interface
runs, the more damage accumulates. This issue now is found on LX2160A
eSDHC1 for only SD card.
The hardware workaround is recommended to use an on-board level shifter
that is 1.8v on SoC side and 3.3v on SD card side.
For boards without hardware workaround, this option could be enabled,
ensuring 1.8v IO voltage and disabling eSDHC if no card.
This option assumes no hotplug, and u-boot has to make all the way to
to linux to use 1.8v UHS-I speed mode if has card.
If you do not want the workaround for better user experience, of course
you can choose to not select it running eSDHC in unsafe mode.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
change to how sequence numbers are assigned to devices
minor fixes and improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl7kQ4kRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZrvAgAqc/TEj7QHPyW9rQSl8h65MXK93qRsnZo
4segKEtK0Rmv0S2VfmPCwujsDFl5gZUNt+rXD/l7F0a4Wzx4eYgYrEXOYsXs/ZHP
jjGrcbvO4Qkx3QzjMqqoUiQqeCgNQ9XIre8F+1NmZeQ2bFtPKbJXtXKYTcMI1wSW
PhRGbbsTnKNKC0dL0nLFG6+NC/sk6xRqMx28Ip38FTrQL+Uh67LZFpLkY3yuHo/1
CVhCw+7Aov0I6tDrdKrngjFqXRSoTsuOhavSFoW9U6llqDL7FIC6aoRo7x24lSJN
VFTRpXPmNHeslE6NHEOQs9elFpbxXR34te3k4p74rFuX/J/490UaYA==
=172C
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-12jun20' of git://git.denx.de/u-boot-dm into next
patman improvements to allow it to work with Zephyr
change to how sequence numbers are assigned to devices
minor fixes and improvements
The random_port() routine is not used anywhere else. Make it local to
dns.c to reduce code clutter, and shrink generated code a little.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Add phy_set/clear_bit helper routines so that ported drivers from the
kernel can use these functions.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Fix kernel doc warnings in phy.h. Mostly the warnings were due to the
return missing the semi-colon.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Add kernel doc to the phy_read/write utility functions in phy.h
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
This keeps the compatibility with the old bootcmd.
The fdtfile environment variable also needed to be set to
imx6q-tbs2910.dtb to enable booting mainline kernels
otherwise with extlinux.conf it tries to load
mx6-tbs2910.dtb instead.
With arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola
GNU/Linux distribution, we have the following size
differences:
- text: +2041 bytes
- data: 0 bytes
- bss: 0 bytes
- total: +2041 bytes
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org>
Reviewed-by: Soeren Moch <smoch@web.de>
This doesn't affect the size of the image: with
arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola GNU/Linux
distribution, the text, data, bss and total sizes remain
unchanged.
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org>
Reviewed-by: Soeren Moch <smoch@web.de>
The current recommendation for best security practice from the US government
is to use SHA384 for TOP SECRET [1].
This patch adds support for SHA384 and SHA512 in the hash command, and also
allows FIT images to be hashed with these algorithms, and signed with
sha384,rsaXXXX and sha512,rsaXXXX
The SHA implementation is adapted from the linux kernel implementation.
[1] Commercial National Security Algorithm Suite
http://www.iad.gov/iad/programs/iad-initiatives/cnsa-suite.cfm
Signed-off-by: Reuben Dowle <reuben.dowle@4rf.com>
If there are aliases for an uclass, set the base for the "dynamically"
allocated numbers next to the highest alias.
Please note, that this might lead to holes in the sequences, depending
on the device tree. For example if there is only an alias "ethernet1",
the next device seq number would be 2.
In particular this fixes a problem with boards which are using ethernet
aliases but also might have network add-in cards like the E1000. If the
board is started with the add-in card and depending on the order of the
drivers, the E1000 might occupy the first ethernet device and mess up
all the hardware addresses, because the devices are now shifted by one.
Also adapt the test cases to the new handling and add test cases
checking the holes in the seq numbers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Alex Marginean <alexandru.marginean@nxp.com>
Tested-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Michal Simek <michal.simek@xilinx.com> [on zcu102-revA]
If CONFIG_DM_DEV_READ_INLINE is set, dev_read_alias_highest_id() calls
libfdt_get_highest_id(). But this function is only available if we have
libfdt compiled in. If its not available return -1, which matches the
return code for no alias found.
This fixes the following error on omapl138_lcdk:
arm-linux-gnueabi-ld.bfd: drivers/built-in.o: in function `dev_read_alias_highest_id':
/home/mw/repo/u-boot/include/dm/read.h:986: undefined reference to `fdtdec_get_alias_highest_id'
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Acked-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Acked-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Now all boards which are using davinci SPI driver
have moved to SPL_DM so drop the unneeded non-dm code.
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
This would make SPL build to DM_SPL, SPL_OF_CONTROL.
Build fine with but not tested.
Cc: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The u-boot-spl.bin pad with ddr firmware conflicts with the
CONFIG_MALLOC_F_ADDR area, the ddr firmware will be overwritten
by malloc in SPL stage and cause ddr initialization not able
to finish. So update the related addresses to fix the issue.
Reported-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Board has flash chip on board so let store U-Boot environment there.
Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Mark the default U-Boot environment as SPI flash since
this is an on board flash device.
Updated env offset, size in contrast with default since
the U-Boot proper has to start from 384K.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This converts the following to Kconfig:
CONFIG_BZIP2
CONFIG_GZIP
CONFIG_LZO
CONFIG_ZLIB
CONFIG_LZMA
CONFIG_LZO
Signed-off-by: Tom Rini <trini@konsulko.com>
Per the boards config header file, there is no useful GPIO on these
boards. Remove CONFIG_CMD_GPIO from the defconfigs.
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
The config header for this platform disables both CMD_SF and CMD_SPI and
the defconfig leaves them enabled. Disable them from the defconfig and
enable them in the header.
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masakazu Mochizuki <masakazu.mochizuki.wd@hitachi.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The common config header for bcm7260 and bcm7445 enable
CONFIG_CMD_EXT2/EXT4 but the defconfigs do not. This results in the
commands being disabled. Enable them via the defconfig.
Cc: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The config header for this platform uses '#undef' in a number of cases.
All of the MMC related ones were already handled correctly in the
defconfig file. In the case of CONFIG_CMD_FUSE, the command was being
built and enabled via defconfig. Disable it in the defconfig, cleanup
the header.
Reviewed-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Rather than only enable CONFIG_CMD_NAND for non-SPL builds, move the CMD
options to defconfig and rework the guards to not try and call the
function in SPL builds.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The symbol "CONFIG_ARM_DCC" is used to control building
drivers/serial/arm_dcc.c. Provide a simple Kconfig entry for this.
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Tom McLeod <tom.mcleod@opalkelly.com>
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
This is a sample GPT partition layout for SD card,
right now three important partitions are added to
make the system bootable.
partition layout:
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000022 0x00000821 "loader1"
attrs: 0x0000000000000000
type: 5b193300-fc78-40cd-8002-e86c45580b47
guid: cbcbef44-e627-42bc-b134-93b6f3784b8c
2 0x00000822 0x00002821 "loader2"
attrs: 0x0000000000000000
type: 2e54b353-1271-4842-806f-e436d6af6985
guid: f54eba28-d8de-4852-978d-1a673777e2ae
3 0x00002822 0x00020821 "rootfs"
attrs: 0x0000000000000004
type: 0fc63daf-8483-4772-8e79-3d69d8477de4
type: linux
guid: 9561df46-8d55-4799-a83b-cfee9ef6ff93
Note:
- loader1 would be fsbl or spl
- loader2 would be U-Boot or U-Boot proper
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Add a support for SPL which will boot from L2 LIM (0x0800_0000) and
then SPL will boot U-Boot FIT image (OpenSBI FW_DYNAMIC + u-boot.bin)
from MMC boot devices.
SPL related code is leveraged from FSBL
(https://github.com/sifive/freedom-u540-c000-bootloader.git)
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
This patch series addresses the following issues:
* allow compiling with clang
* add missing function descriptions to the HTML documentation
* simplify the validation of UEFI images
* validate load options in the UEFI boot manager
In a preparatory patch a structure definition is moved.
-----BEGIN PGP SIGNATURE-----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=rbBa
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-07-rc4' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc4
This patch series addresses the following issues:
* allow compiling with clang
* add missing function descriptions to the HTML documentation
* simplify the validation of UEFI images
* validate load options in the UEFI boot manager
In a preparatory patch a structure definition is moved.
For passing the optional data of the load option to the loaded imaged
protocol we need its size.
efi_deserialize_load_option() is changed to return the size of the optional
data.
As a by-product we get a partial validation of the load option.
Checking the length of the device path remains to be implemented.
Some Coverity defects identified the load options as user input because
get_unaligned_le32() and get_unaligned_le16() is called. But non of these
Coverity defects can be resolved without marking functions with Coverity
specific tags.
Reported-by: Coverity (CID 303760)
Reported-by: Coverity (CID 303768)
Reported-by: Coverity (CID 303776)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is defined in the asm/cache.h header file. Update this header file to
include it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
The get_sw_write_prot API is used to get the write-protected
bits of flash by reading the status register and other wards
it's API for reading register bits.
1) This kind of requirement can be achieved using existing
flash operations and flash locking API calls instead of
making a separate flash API.
2) Technically there is no real hardware user for this API to
use in the source tree.
3) Having a flash operations API for simple register read bits
also make difficult to extend the flash operations.
4) Instead of touching generic code, it is possible to have
this functionality inside spinor operations in the form of
flash hooks or fixups for associated flash chips.
Considering all these points, this patch drops the get_sw_write_prot
and associated code bases.
Cc: Simon Glass <sjg@chromium.org>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Let move 8/16-bit UTMI+ interface initialization into DWC3 core init
that is convenient for both DM_USB and u-boot traditional process.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds a quirk to disable USB 2.0 MAC linestate check
during HS transmit. Refer the dwc3 databook, we can use it for
some special platforms if the linestate not reflect the expected
line state(J) during transmission.
When use this quirk, the controller implements a fixed 40-bit
TxEndDelay after the packet is given on UTMI and ignores the
linestate during the transmit of a token (during token-to-token
and token-to-data IPGAP).
On some rockchip platforms (e.g. rk3399), it requires to disable
the u2mac linestate check to decrease the SSPLIT token to SETUP
token inter-packet delay from 566ns to 466ns, and fix the issue
that FS/LS devices not recognized if inserted through USB 3.0 HUB.
Reference from below Linux commit,
commit <65db7a0c9816> ("usb: dwc3: add disable u2mac linestate
check quirk")
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a quirk to clear the GUSB2PHYCFG.U2_FREECLK_EXISTS bit,
which specifies whether the USB2.0 PHY provides a free-running
PHY clock, which is active when the clock control input is active.
Refer to commit 27f83eeb6b42("usb: dwc3: add dis_u2_freeclk_exists_quirk")
in Linux Rockchip Kernel.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Add a quirk to clear the GUSB2PHYCFG.ENBLSLPM bit, which controls
whether the PHY receives the suspend signal from the controller.
Refer to commit ec791d149bca("usb: dwc3: Add dis_enblslpm_quirk")
in Linux Kernel.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
U-Boot has video output enabled so time to get keyboard working.
=> usb reset;usb tree
resetting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3a0000: USB OHCI 1.0
Bus usb@fe3c0000: USB EHCI 1.00
Bus usb@fe3e0000: USB OHCI 1.0
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found
scanning bus usb@fe3a0000 for devices... 1 USB Device(s) found
scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
scanning bus usb@fe3e0000 for devices... 3 USB Device(s) found
scanning bus dwc3 for devices... cannot reset port 1!?
2 USB Device(s) found
scanning usb for storage devices... 2 Storage Device(s) found
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
1 Hub (12 Mb/s, 0mA)
U-Boot Root Hub
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
1 Hub (12 Mb/s, 0mA)
| U-Boot Root Hub
|
+-2 Hub (12 Mb/s, 100mA)
| ALCOR Generic USB Hub
|
+-3 Mass Storage (12 Mb/s, 200mA)
Kingston DT 101 G2 001478544887BB3157380157
1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|
+-2 Mass Storage (5 Gb/s, 76mA)
ADATA ADATA USB Flash Drive 1520405012240002
Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Include NVME in the list of boot targets if CONFIG_NVME is enabled.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The size is not actually used since it is present in the header. Drop this
parameter. Also tidy up error handling while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Currently we support reading a file from CBFS given the address of the end
of the ROM. Sometimes we only know the start of the CBFS. Add a function
to find a file given that.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function currently returns a node pointer so there is no way to know
the error code. Also it uses data in BSS which seems unnecessary since the
caller might prefer to use a local variable.
Update the function and split its body out into a separate function so we
can use it later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We may as well return the error code and use it directly in the command
code. CBFS still uses its own error enum which we may be able to remove,
but leave it for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
U-Boot uses ulong for addresses but there are a few places in this driver
that don't use it. Convert this driver over to follow this convention
fully.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is not definded anywhere.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.gpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Convert the CRS305-1G-4S board to CRS3xx-98DX3236 to enable easier
implementation of new CRS3xx series boards, based on Marvell Prestera
98DX3236.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Without CONFIG_SYS_U_BOOT_OFFS set to CONFIG_SYS_SPI_U_BOOT_OFFS, U-Boot
will be located at address 0x16000. But, SPL will try to load the
payload from 0x24000 causing the boot to hang.
Signed-off-by: Ezra Buehler <ezra@easyb.ch>
Reviewed-by: Stefan Roese <sr@denx.de>
CONFIG_BZIP2 and CONFIG_GZIP_COMPRESSED are Kconfig options. Select them
by CONFIG_SANDBOX instead of setting them in configs/sandbox.h.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the device firmware update functions to the generated HTML
documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
Convert CONFIG_KS8851_MLL and CONFIG_KS8851_MLL_BASEADDR to Kconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Problems fixed with these patches are:
* UEFI sub-system not working with virtio block devices
* Missing SATA support in UEFI sub-system
* A superfluous debug statement
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAl7Hb8sACgkQxIHbvCwF
GsR3tA/+NknuzED4AkdVL0uRWw4kZNcSqxY+lpFUC73iWN0gLTWKFO6IXDRF4Jox
3/xWSkMuPkeAp6sjl+Gv8DD2DCkNJedXeMdeAGZzPDLfXn16wmzhjvIe5xz8cr/2
0shL5PtTWK8BR/ClSxTANoYrASGUISIpyq3Tu/dKY9PCGesfvzObmv+n06HizR+b
E2ceSqVfEBZNLkp38o/PAOdrayjJCz7oSGxBhFQx1x3LYV/G6iHWdg9Kw+KsVdmR
GBh1frun8MbC9NOqWjdnMmKi1CeHeCvvBu38lXzpVlfB0VcC2UFeuGaRh1aDKdnq
CAiV20v9JygEwcxLGIEU4r+RwoqSxkbMbB2nlLnDuFmoJCC8gEK0ctUaFFrOV9i3
xB/ynnw4zlht039fv8Qaq6OPiHbzA5qGmE93DY4p6a+iV0Mplfy6qLXw+UWpFEGG
lGBZ2NPu04qjbZdzKCDag6Uw3oEypYMe3CO8Hg7EAQBB49v10LdhtgPm2BgZaaJn
ZmYqzF0+FB1znPGmu6hrxT6IPHy+fP0cxxEma5kxXTp6CapXLHl84v4JGqNPpqmN
jPV4MtmZaBXgasL1TDUCgpuNTEVcBcl49VastpPNMNjPPE/UD+oUXHbW+Lp1u1BH
Jn5rCODNi5gah1X/vQ+yFC7Pk95RE0vqYDbdSUR2Wn1WurfbMzQ=
=o+Cy
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-07-rc3-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc3 (2)
Problems fixed with these patches are:
* UEFI sub-system not working with virtio block devices
* Missing SATA support in UEFI sub-system
* A superfluous debug statement
Reference to commit that adds HDMI to other rk3399 boards:
commit 9778edae55 ("rockchip: Enable HDMI output on rk3399 board w/ HDMI")
Signed-off-by: Andrius Štikonas <andrius@stikonas.eu>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Provide device path nodes for SATA devices.
This avoids creation of two handles with the same device path indicating
our root node.
This is what the device paths for a SATA drive with four partitions could
like:
/VenHw(..)/Sata(0x0,0xffff,0x0)
/VenHw(..)/Sata(0x0,0xffff,0x0)/HD(1,MBR,0x81ea591f,0x800,0x63ff830)
/VenHw(..)/Sata(0x0,0xffff,0x0)/HD(2,MBR,0x81ea591f,0x6400800,0x9ff830)
/VenHw(..)/Sata(0x0,0xffff,0x0)/HD(3,MBR,0x81ea591f,0x6e00800,0x16ef2ab0)
/VenHw(..)/Sata(0x0,0xffff,0x0)/HD(4,MBR,0x81ea591f,0x1dcf3800,0x1dcedab0)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The UEFI specification does not define a device sub-type for virtio.
Let's use a vendor hardware node here.
This avoids creation of two handles with the same device path indicating
our root node.
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The UEFI 2.8 specification has introduced the EFI_MEMORY_SP memory
attribute. Add it to the 'efidebug memmap' and 'efi mem' commands.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- Add DM_ETH support for lx2160aqds, ls2080aqds, ls1088aqds
- QSI related fixes on ls1012a, ls2080a, ls1046a, ls1088a, ls1043a based
platforms
- Bug-fixes/updtaes related to ls1046afrwy, fsl-mc, msi-map property
Add weak function which is called right after fdtdec_setup() configured
the U-Boot DT. This permits board-specific adjustments to the U-Boot DT
before U-Boot starts parsing the DT. This could be used e.g. to patch in
various custom nodes or merge in DT fragments from prior-stage firmware.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
the mpc83xxx suvd3 variant is not longer used, so
remove it.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This macro is only used (tested for existence) in mpc83xx.c, which
unconditionally includes mpc83xx.h where it is unconditionally
defined. Removing it makes the remaining code easier to read.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
ls1046afrwy does not support sata boot.
So Override default BOOT_TARGET_DEVICES
and support only mmc, usb and dhcp as boot targets.
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_SYS_MALLOC_LEN is currently set to low value and leaves very less
space to do malloc in flash environmet. Increase the value to get more
memory and also make it align with other boards(ls1046a, ls1043a etc.)
config values.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
BOOT command currently access spi-nor flash memory directly. As per spi-mem
framework, flash memory access via absolute addresses is no more possible.
Use flash APIs to access memory instead of directly using it.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
MC_INIT command currently access spi-nor flash memory directly. As per
spi-mem framework, flash memory access via absolute addresses is no more
possible. Use flash APIs to access memory instead of directly using it.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable CONFIG_SPI_FLASH_SPANSION in defconfigs of LS1046ARDB and
LS1046AQDS which have two spansion flases i.e s25fs512s each of size
64M.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Since CONFIG_FSL_QSPI is already enabled for LS1012A in defconfigs. Also
enable CONFIG_SPI_FLASH_SPANSION for LS1012A boards having spansion
flashes.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move CONFIG_FSL_QSPI to the board defconfigs and while at it also move
CONFIG_SPI_FLASH_SPANSION for LS1043AQDS.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Some of these options are not used by the driver anymore and some of
them are obsolete as the information is gathered from the dt. Also
consolidating defines in common headers.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Some places use __ASSEMBLER__ instead which does not work since the
Makefile does not define it. Fix them.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not be using typedefs and these make it harder to use
forward declarations (to reduce header file inclusions). Drop the typedef.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is bad practice to include common.h in other header files since it can
bring in any number of superfluous definitions. It implies that some C
files don't include it and thus may be missing CONFIG options that are set
up by that file. The C files should include these themselves.
Update some header files in arch/arm to drop this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this uncommon header out of the common header.
Fix up some style problems in flash.h while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
In Arm devices OP-TEE has the ability to run StandAloneMM (from EDK2)
in a separate partition and handle UEFI variables.
A following patch introduces this functionality.
Add the headers needed for OP-TEE <--> StandAloneMM communication
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Virtually all callers of this function do the rounding on their own.
Some do it right, some don't. Instead of doing this in each caller,
do the rounding in efi_add_memory_map(). Change the size parameter
to bytes instead of pages and remove aligning and size calculation in
all callers.
There is no more need to make the original efi_add_memory_map() (which
takes pages as size) available outside the module. Thus rename it to
efi_add_memory_map_pg() and make it static to prevent further misuse
outside the module.
Signed-off-by: Michael Walle <michael@walle.cc>
Add missing comma in sunxi_display.c.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Enable CONFIG_PCI_INIT_R for qemux86 and qemux86-64 pci enumeration during
boot in order to eliminate the custom preboot commands in
include/configs/qemu-x86.h.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
The speed member actually uses an enum, so add this to the comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Add prototype for function dfu_transaction_initiate and
dfu_transaction_cleanup to avoid warning with W=1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a function g_dnl_set_product to change the Product string used in USB
enumeration in any command based on download gadget.
If the function is called with NULL pointer, the product string is set to
the default value (product[] = "USB download gadget").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Manage BOOT_FLASH_SPINAND, with boot_device="spi-nand"
and treat this value in bootcmd_stm32mp.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add reserve memory for OP-TEE in U-Boot and in kernel device tree:
- no more reduce the DDR size in "memory" node:
CONFIG_SYS_MEM_TOP_HIDE is no more used
- U-Boot device-tree defines the needed "reserved-memory" for OP-TEE
and U-Boot should not use this reserved memory: board_get_usable_ram_top
use lmb lib to found the first free region, the not reserved
memory, enough to relocate U-Boot: the needed size of U-Boot
is estimated with gd->mon_len + CONFIG_SYS_MALLOC_LEN.
- the optee node ("optee@...": firmware with compatible "linaro,optee-tz")
and the associated "reserved-memory" are deactivated in kernel device
tree when OP-TEE is not detected by U-Boot to prevent kernel issue
(memory is reserved but not used, optee driver probe failed).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch reduces the stm32mp1 environment size and builds
dynamically the MTD partitions with information from defconfig
(CONFIG_MTDPARTS_...).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch reduces the stm32mp1 environment size and
builds dynamically the DFU board configuration with gpt
and mtd partitions and information from defconfig
(CONFIG_DFU_ALT_RAM0).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The AV96 board does exist in multiple variants. To cater for all of
them, implement board code handling. There are two GPIOs which code
the type of the board, read them out and use the value to pick the
correct device tree from an fitImage.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: Iddb330b9a66500495885457cbe17edc0eacaaf43
Add a quirk to clear the GUSB3PIPECTL.DELAYP1TRANS bit,
which specifies whether disable delay PHY power change
from P0 to P1/P2/P3 when link state changing from U0
to U1/U2/U3 respectively.
Reference from below Linux commit,
commit <00fe081dc3a3> ("usb: dwc3: add dis_del_phy_power_chg_quirk")
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This pull request comprises:
* bug fixes
* documentation fixes
* a new function to determine u16 string sizes and its unit test
-----BEGIN PGP SIGNATURE-----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=vqQZ
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-07-rc2-4' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc2-4
This pull request comprises:
* bug fixes
* documentation fixes
* a new function to determine u16 string sizes and its unit test
After this change both device display and serial console would contain
U-Boto output automatically without any future configuration. This would
allow easier debugging on real device as access to serial console is hard
and also in qemu emulator where it is easier to copy+paste from serial
console as from SDL framebuffer.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Now when code for defining partitions is duplicated at two locations
(option CONFIG_MTDPARTS_DEFAULT in nokia_rx51_defconfig file and macro
OMAP_TAG_PARTITION_CONFIG in rx51.c file) there is no need to have common
macros. Lets inline PART* macros to rx51.c file.
Signed-off-by: Pali Rohár <pali@kernel.org>
In commit commit 43ede0bca7 ("Kconfig: Migrate MTDIDS_DEFAULT /
MTDPARTS_DEFAULT") were removed definitions for onenand partitions.
Revert them back and enable needed options for onenand support.
Signed-off-by: Pali Rohár <pali@kernel.org>
In commit commit 37304aaf60 ("Convert CONFIG_USE_PREBOOT and
CONFIG_PREBOOT to Kconfig") was moved complicated multiline script code
from C header to oneliner in defconfig. After this change multiline to wide
oneliner it is hard to read this code and even harder to debug. Moreover
this script code should be at place where are other scripts, so move it
back to C header file.
Define new env variable preboot which stores this script and in option
CONFIG_PREBOOT calls this preboot variable.
Signed-off-by: Pali Rohár <pali@kernel.org>
In commit commit 278b90ce78 ("configs: Migrate CONFIG_SYS_TEXT_BASE") was
moved definition for CONFIG_SYS_TEXT_BASE option but author probably forgot
to move also comment for lines which are moving. So do it now!
Signed-off-by: Pali Rohár <pali@kernel.org>
Add readl poll API with sleep and timeout support.
This change is referenced from Linux from below commit:
commit <5f5323a14cad19323060a8cbf9d96f2280a462dd> ("iopoll:
introduce read_poll_timeout macro")
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Some drivers and other bsp code not only poll the
register with timeout but also required to delay
on each transaction.
This patch add that requirement by adding sleep_us
variable so-that read_poll_timeout now support
delay as well.
This change is referenced from Linux from below commit:
commit <5f5323a14cad19323060a8cbf9d96f2280a462dd> ("iopoll:
introduce read_poll_timeout macro")
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add read_poll_timeout common API similar to Linux iopoll.
readx_poll_timeout will trigger read_poll_timeout with
proper op. This will help to extend the functionalities
like sleep_us to poll timeout in future.
This change is referenced from Linux from below commit:
commit <5f5323a14cad19323060a8cbf9d96f2280a462dd> ("iopoll:
introduce read_poll_timeout macro")
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
clk function names in comments should be prefix with
clk instead of clock.
Fix it.
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Clients that are requesting some of uclass API's
without a device (with ofnode) usually have _nodev
naming convention.
- clk_get_by_index_nodev
- clk_get_by_name_nodev
- reset_get_by_index_nodev
- gpio_request_by_name_nodev
So, update the same naming convention PHY framework.
This doesn't change the existing functionality.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
node is most of device related API's are termed as device
node and without device related API's are termed as ofnode.
generic_phy_get_by_node API is without device API, so fixed
the node description as ofnode.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
lpc32xx_ssp driver is deprecated, no active updates
and no board user, hence dropped the same.
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.aribaud@3adev.fr>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
When doing partition reboot, the boot image won't be reloaded by ROM,
it is just CPU reset to boot entry. The SW has to keep the boot image
inside the RAM unchanged. It includes both the TEXT section and DATA
section.
For SPL, the problem is DATA section will be updated at runtime, so in
next partition reboot the data is not same as the initial value from
cold boot. If any code depends on the initial value, then it will have
problem.
This patch introduces a mechanism to recover the data section
for partition reboot. It adds a new section in image for saving
data section. When from cold boot, the data section will be saved
to that new section at SPL early phase. When from partition reboot,
the data section will be restored from the new section.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add more BCH setting mode and remove the unnecessary platform constrain
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Beacon EmbeddedWorks, formerly known as Logic PD, is releasing
a devkit based on the i.MX8M Mini SoC consisting of baseboard +
SOM.
It supports eMMC on the SOM, microSD on the baseboard, various
GPIO, the PINCTRL, and UART.
Signed-off-by: Adam Ford <aford173@gmail.com>
Provide an option in DT to use legacy bch geometry, which compatible
with the 3.10 kernel bch setting. To enable the feature, adding
"fsl,legacy-bch-geometry" under gpmi-nand node.
NOTICE: The feature must be enabled/disabled in both u-boot and kernel.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The code change updated the NAND driver BCH ECC layout algorithm to
support large oob size NAND chips(oob > 1024 bytes) and proposed a new
way to set ECC layout.
Current implementation requires each chunk size larger than oob size so
the bad block marker (BBM) can be guaranteed located in data chunk. The
ECC layout always using the unbalanced layout(Ecc for both meta and
Data0 chunk), but for the NAND chips with oob larger than 1k, the driver
cannot support because BCH doesn’t support GF 15 for 2K chunk.
The change keeps the data chunk no larger than 1k and adjust the ECC
strength or ECC layout to locate the BBM in data chunk. General idea for
large oob NAND chips is
1.Try all ECC strength from the minimum value required by NAND spec to
the maximum one that works, any ECC makes the BBM locate in data chunk
can be chosen.
2.If none of them works, using separate ECC for meta, which will add one
extra ecc with the same ECC strength as other data chunks. This extra
ECC can guarantee BBM located in data chunk, of course, we need to check
if oob can afford it.
Previous code has two methods for ECC layout setting, the
legacy_calc_ecc_layout and calc_ecc_layout_by_info, the difference
between these two methods is, legacy_calc_ecc_layout set the chunk size
larger chan oob size and then set the maximum ECC strength that oob can
afford. While the calc_ecc_layout_by_info set chunk size and ECC
strength according to NAND spec. It has been proved that the first
method cannot provide safe ECC strength for some modern NAND chips, so
in current code,
1. Driver read NAND parameters first and then chose the proper ECC
layout setting method.
2. If the oob is large or NAND required data chunk larger than oob size,
chose calc_ecc_for_large_oob, otherwise use calc_ecc_layout_by_info
3. legacy_calc_ecc_layout only used for some NAND chips does not contains
necessary information. So this is only a backup plan, it is NOT
recommended to use these NAND chips.
Signed-off-by: Han Xu <b45815@freescale.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
For dual ethernet controllers, the HW design may connect ETH phys to
one MDIO ports. So two different ethernet drivers have to share MDIO bus.
Since two ethernet drivers are independent, we can't ensure their probe
order.
To resolve this problem, introduce an eth phy generic driver and uclass.
After eth-uclass binds, we search the mdio node and binds the phy node
with the eth-phy-generic driver.
When one eth driver get its phy device, the parent of phy device will
probe prior than phy device. So this ensure the eth driver ownes the
MDIO bus will be probed before using its MDIO.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add initial support for Technexion Pico-iMX8MQ SoM on PicoPI carrier
board. Currently working is ethernet, serial, eMMC. DT is imported
from Linux 5.4.28 ("462afcd6e7ea") .
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The env variable overlay_files is used while adding the environment
support commands for FIT loading, but it was cleaned up just prior in
commit ee53b59511 ("configs: Remove unneeded overlay_files environment
variable"). Fix this by replacing the undefined variable with the
proper name_overlays env variable.
Fixes: 76470b6929 ("configs: ti: Add environment support commands for FIT loading")
Signed-off-by: Suman Anna <s-anna@ti.com>
The current code uses 'u16_strlen(x) + 1) * sizeof(u16)' in various
places to calculate the number of bytes occupied by a u16 string.
Let's introduce a wrapper around this. This wrapper is used on following
patches
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add the UEFI unit test helper functions to the generated HTML
documentation.
Correct some documentation texts in include/efi_selftest.h.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Strict naming conventions have to be followed for Python function
generate_ut_subtest() to collect C unit tests to be executed via
command 'ut'.
Describe the requirements both on the C as well on the Python side.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
The commit e89f8aae3d ("treewide: Migrate CONFIG_SYS_ALT_MEMTEST to Kconfig")
setup correct dependency on MEMTEST that's why there is no reason to enable
enable alternate memtest without mtest command.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no real need to exactly define space for saving patterns for
alternate memory test. It is much easier to allocate space on the stack and
use it instead of trying to find out space where pattern should be saved.
For example if you want to test the whole DDR memory you can't save patter
to DDR and you need to find it out. On Xilinx devices DDR or OCM addresses
were chosen but that means that OCM needs to be mapped and U-Boot has
access permission there.
It is easier to remove this limitation and simply save it on stack because
it is very clear that memory test can't rewrite U-Boot and U-Boot has also
full access to memory where runs from.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Move CONFIG_SYS_MTDPARTS_RUNTIME into Kconfig done by moveconfig.py.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support for configuring the CLK_25M pin as well as the RGMII I/O
voltage by the device tree.
By default the AT803x PHYs outputs the 25MHz clock of the XTAL input.
But this output can also be changed by software to other frequencies.
This commit introduces a generic way to configure this output.
Also the PHY supports different RGMII I/O voltages: 1.5V, 1.8V and 2.5V.
An internal LDO is able to provide 1.5V (default) and 1.8V. The 2.5V
option needs an external supply voltage. This commit adds support to
switch the internal LDO to 1.8V.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Currently displaying status line is done in a weak function
menu_display_statusline().
bootmenu.c overrides the weak default function.
It calls menu_default_choice() and interprets the data as
struct bootmenu_entry.
pxe boot also uses common menu code for pxe menus.
If there is a system that enables both bootmenu and pxe,
menu_display_statusline() defined in bootmenu.c will be called
and it will interpret struct pxe_label as struct bootmenu_entry.
This leads to data aborts and pxe menu corruptions.
This patch adds support for client defined statusline function
to resolve the above bug.
Signed-off-by: Thirupathaiah Annapureddy <thiruan@linux.microsoft.com>
CONFIG_SEMIHOSTING is selected for the VFP target by the means of
Kconfig already, there is no need to check this in the header file.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Juno board features a standard compliant EHCI/OHCI USB host
controller pair, which we can just enable.
The platform data is taken from the device tree.
This allows to use USB mass storage (the only storage on a Juno r0)
for loading.
At least on my board USB seems a bit flaky, I need two "usb reset"
sequences after the "usb start" to detect an USB hard drive.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The UART base clock rate was typo-ed in the header file, probably because
the reference (the Linux .dts) was also wrong[1].
Fix the number to make the baud rate more correct.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=39a1a8941b2
Reviewed-by: Simon Glass <sjg@chromium.org>
The U-Boot documentation explains that variables ending with "_r" hold
addresses in DRAM, while those without that ending point to flash/ROM.
The default variables for the Juno board pointing to the kernel and DTB
load addresses were not complying with this scheme: they lack the
extension, but point to DRAM. This is particularly confusing since the
Juno board features parallel NOR flash, so there *is* a memory mapped
NOR address holding a DTB, for instance.
Fix the variables to use the proper names, changing initrd_addr to
ramdisk_addr_r on the way, which seems to be more prevelant and
documented. On the way adjust the FDT load address to be situated
*before* the kernel, since users happened to overwrite the DTB by the
kernel clearing its .BSS section during initialisation.
Also remove the fdt_high and initrd_high variables (which were set
to -1), to allow U-Boot moving those images around.
This should avoid many problems in the future, but breaks loading
Linux kernels < v4.2, since they expect the DTB to be loaded in the same
512MB region as the kernel. If you need to load such an old kernel,
please set fdt_high to either 0xffffffffffffffff or 0xa0000000 (if you
load the kernel to the beginning of DRAM).
That fixes loading debug kernels, which happened to overwrite the DTB on
certain setups.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CMD_EEPROM and ENV_IS_IN_EEPROM can be selected independently, and
cmd/eeprom.o gets built in either case, so whether to declare the real
prototypes needs to follow the same logic as whether cmd/eeprom.c is
built. Otherwise a ENV_IS_IN_EEPROM=y, CMD_EEPROM=n build fails
cmd/eeprom.c:73:1: error: expected identifier or ‘(’ before ‘{’ token
{
While at it, fix the dummy replacements (at least assuming they are
meant to allow the code to compile) - they need to have the same type
as the expression they replace, or one gets errors such as
env/eeprom.c: In function ‘eeprom_bus_read’:
env/eeprom.c:37:8: error: void value not ignored as it ought to be
rcode = eeprom_read(dev_addr, offset, buffer, cnt);
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch contains error corrections and code simplifications for the UEFI
sub-system.
-----BEGIN PGP SIGNATURE-----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=+u1X
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-07-rc2-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc2-2
This patch contains error corrections and code simplifications for the UEFI
sub-system.
- Add DM model for P1010RDB
- Add I2C DM Model support for P1010RDB, T1042RDB, T2080, T4240RDB,
MPC8548CDS, T1024RDB, P4080, P3041DS, P2041RDB, P2020RDB, P1020RDB,
P5040DS
- Fix reference to READM.qe_firmware
- dts clean up to use -u-boot for px30, rk3399 boards
- dts sycn from upstream kernel for rk3328, rk3399
- add rockchip rng driver
- new board support: rk3328-roc-cc, rk3399-roc-pc,Nanopi M4 2GB
This is part 1 of big network cleanup / DM conversion.
The dc2114x/rtl8139/pcnet/tulip PCI adapter drivers received checkpatch
cleanups in preparation for DM conversion. The smc911x is converted to
DM completely. The dwc_eth_qos cache fixes are applied.
This function will check if a given handle to device is an EFI system
partition. It will be utilised in implementing capsule-on-disk feature.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Add function description. Return bool.
Reviewed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Pkcs7_parse.h and x509_parser.h are used in UEFI subsystem, in particular,
secure boot. So move them to include/crypto to avoid relative paths.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Don't include include x509_parser.h twice.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In two files README.qe_firmware is referenced which never made it into the
U-Boot tree. The README is available in the Linux kernel tree.
Update the references.
Cc: Timur Tabi <timur@kernel.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When running on SoC with multiple clusters, the boot CPU may
not be fixed, saying booting from cluster A or cluster B.
Add a API that can return the udevice for current boot CPU.
Cpu driver needs to implement is_current_cpu interface for this
feature, otherwise the API only returns the first udevice in
cpu uclass.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
This patch is used to support the on-chip xHCI controller on
MediaTek SoCs, currently control/bulk/interrupt transfers are
supported.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Get a group of phys by the phy bulk API
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds a "bulk" API to the phy API in order to
get/init/exit/power on/off a group of phys associated
with a device.
The bulk API will avoid adding a copy of the same code to
manage a group of phys in drivers.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This patch add function used to get the child count of
a ofnode or a device
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Do this as a preparation for removing initr_bedbug wrapper from
common/board_r.c.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move CONFIG_SYS_ARM_CACHE_WRITETHROUGH and
CONFIG_SYS_ARM_CACHE_WRITEALLOC into Kconfig done by moveconfig.py.
Kconfig uses a choice between the 3 values supported in U-Boot,
including the new configuration CONFIG_SYS_ARM_CACHE_WRITEBACK
(the default configuration).
The patch also avoids to select simultaneously 2 configurations.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add initial support for Google's Coral Dev Board based on i.MX8MQ.
https://coral.ai/products/dev-board
The Phanbell naming has been used here to match the naming convention
used in Google's U-Boot source tree:
https://coral.googlesource.com/uboot-imx/
Co-developed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Tested-by: Marco Franchi <marcofrk@gmail.com>
A comment note has been left after completing pinctrl listing, so let's
remove it since it's useless.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Some of these options are not used by the driver anymore and some of them
are obsolete as the information is gathered from the dt.
So, remove the unused config options now.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
define FEC_ENET_ENABLE_TXC_DELAY to enable the delay on TXC line on
the MAC. This has to be done in order to meet RGMII specs.
According to RGMII specs the clock should get delayed so the edges of
the clock are preferrably in the middle of the edges of data-lines so
they can be sampled properly.
Our PHY expects the MAC to delay TXC line, as it is also written
in the spec. This patch makes sure the TXC delay on the FEC is enabled
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This patch adds skew register settings for KSZ9131. It checks first
which phy is on the board and then applies the correct skew settings.
Skew settings calculation for the KSZ9131:
The i.MX6 SoC has an output skew tolerance of -100ps to 900ps. All
PCB traces where routed exactly the same length so we can calculate
the skew settings without taking the length into consideration. The
traces are all length matched.
RXC skew (PHY to MAC):
- We use the 2ns DLL controlled delay on the PHY
- We do not use the skew registers
This results in the following values:
RXC
PHY fixed Delay 2000ps
PHY Added Delay 0ps
T_setup_R min 2.00ns
T_setup_R typ 2.00ns
T_setup_R max 2.00ns
T_hold_R min 1.60ns
T_hold_R typ 2.00ns
T_hold_R max 2.40ns
That means we are well within RGMII specs.
TXC skew (MAC to PHY):
- We use the 2ns DLL controlled delay on the PHY
- We then subtract ~0.6ns with TXD[0:3] and TXC clock pad skew
register in a resulting ~1.4ns delay.
This results in the following values under consideration of the
tolerances:
TXC min TXC typ TXC max
MAC min -100ps -100ps -100ps
MAC max 900ps 900ps 900ps
PHY fixed Delay 2000ps 2000ps 2000ps
PHY added Delay -340ps -600ps -859ps
T_setup_T min 1.56ns 1.30ns 1.04ns
T_setup_T typ 2.06ns 1.80ns 1.54ns
T_setup_T max 2.56ns 2.30ns 2.04ns
T_hold_T min 1.04ns 1.30ns 1.56ns
T_hold_T typ 1.94ns 2.20ns 2.46ns
T_hold_T max 2.84ns 3.10ns 3.36ns
This shows that T_hold_T min and T_setup_T min times are out of spec
for RGMII timing. However the KSZ9131 has a minimal value for this time
of 0.8ns which is met under all circumstances.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Move the SIP macro to common header and unify the name to
make others could reuse them.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
These macros guard one switch-case statement, which grows mips malta
by some 20 bytes if debug is enabled, and even less if it is not. To
make the code simpler, just support all the NICs and be done with it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
If the DM_ETH is enabled and netdev.h is included somewhere, the
struct eth_device may not be defined, yet it is used in the header
file as an argument to fecmxc_register_mii_postcall. Add forward
declaration to remove the warning.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
This syncs the rk3328 power domain header file from Linux kernel
next-20200324, to support newer hardware blocks when syncing the
device tree files.
The last non-merge commit to touch it was
b24413180f56 ("License cleanup: add SPDX GPL-2.0 license identifier to files with no license")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Loic Devulder <ldevulder@suse.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This syncs the rk3328 clock header file from Linux kernel next-20200324,
to support newer hardware blocks when syncing the device tree files.
The last non-merge commit to touch it was
0dc14b013f79 ("clk: rockchip: add clock id for watchdog pclk on rk3328")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Loic Devulder <ldevulder@suse.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This pull request contains bug fixes needed due to the merged changes for
EFI secure boot.
Patches are supplied to identify EFI system partitions.
-----BEGIN PGP SIGNATURE-----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=38oT
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-07-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc2
This pull request contains bug fixes needed due to the merged changes for
EFI secure boot.
Patches are supplied to identify EFI system partitions.
Enable QE bit for ISSI flash chips.
QE enablement logic is similar to what Macronix
has, so reuse the existing code itself.
Cc: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable SPI flash(SF) distro boot command in rk3399.
This distro boot will read the boot script at specific
location at the flash and start sourcing the same.
Included the SF device at the last of the target devices
list since all the rest of the devices on the list have
more possibility to boot the distribution due to the
size of the SPI flash is concern.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>