The command 'clocks' shows the following output:
=> clocks
PLL_A7_SPLL 528 MHz
PLL_A7_APLL 529 MHz
PLL_USB 0 MHz
....
[do_mx7_showclocks] addr = 0x9FFB61F1
The last line is not useful at all, so just remove it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Ensure we terminate the line with a CR if we get an invalid sensor device
or reading.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
In order to be able to run the I2C bus at 400Khz, the chip errata[1]
recommends that the peripheral clock runs out of the 24MHz oscillator.
Systems running I2C from OP-TEE before Linux executes - for example to
access a Secure Element [2] providing the cryptographic support - expect
this clock to be configured by the bootloader [3].
[1] IMX6SLCE Rev. 5, 02/2019, ERR007805.
[2] OP-TEE: support for NXP SE05X Plug and Trust (patch on the list).
[3] OP-TEE: check the imx_i2c.c driver (imx6 patch on the list).
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
- New PX30 board: Engicam PX30.Core;
- Fix USB HID support for rock960;
- Remove host endianness dependency for rockchip mkimage;
- dts update for rk3288-tinker;
- Enable console MUX for some ROCKPi boards;
- Add config-based ddr selection for px30;
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
C.TOUCH 2.0 is a general purpose carrier board with capacitive
touch interface support.
PX30.Core needs to mount on top of this Carrier board for creating
complete PX30.Core C.TOUCH 2.0 board.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Engicam C.TOUCH 2.0 is an EDIMM compliant general purpose
carrier board with capacitive touch interface.
Genaral features:
- TFT 10.1" industrial, 1280x800 LVDS display
- Ethernet 10/100
- Wifi/BT
- USB Type A/OTG
- Audio Out
- CAN
- LVDS panel connector
SOM's like PX30.Core needs to mount on top of this Carrier board
for creating complete PX30.Core C.TOUCH 2.0 board.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board from Engicam.
PX30.Core needs to mount on top of this Evaluation board for
creating complete PX30.Core EDIMM2.2 Starter Kit.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
TARGET_EVB_PX30 can be possible to use other px30 boards.
Add the help text for existing EVB, so-that the new boards
which are resuing this config option can mention their board
help text.
This would help to track which boards are using EVB_PX30 config.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
General features:
- Rockchip PX30
- Up to 2GB DDR4
- eMMC 4 GB expandible
- rest of PX30 features
PX30.Core needs to mount on top of Engicam baseboards for creating
complete platform boards.
Possible baseboards are,
- EDIMM2.2
- C.TOUCH 2.0
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out
SOM's like PX30.Core needs to mount on top of this Evaluation board
for creating complete PX30.Core EDIMM2.2 Starter Kit.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add chosen node in -u-boot.dtsi for ROCK-Pi N8 board.
This will help to get serial out messages.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
The property reg-shift with the same value is present in the base
device tree already. Remove unnecessary node from rk3288-tinker.dts.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The I2C EEPROM is present on Tinker Board S as well. Move the i2c node
to the shared, U-Boot specific rk3288-tinker-u-boot.dtsi device tree.
Cc: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This feature is incompatble with of-platdata since it uses the
U_BOOT_DEVICE() macro. With of-platdata the only devices permitted are
those created by dtoc.
The driver is not used in SPL anyway, so exclude it from that build.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Now that parent devices are supported with of-platadata, we don't need the
messy code to fix up the parent pointers and allocations on Apollo Lake.
Put the code behind a condition.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present, enabling CONFIG_APL_SPI_FLASH_BOOT does not build since SPI
and SPI flash are not enabled for TPL. Add a condition to fix this and
tidy up a build warning in the SPI-flash driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a simple test that we can obtain the correct parent for an I2C
device. This requires updating the driver names to match the compatible
strings, adding them to the devicetree and enabling a few options.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have a test in dtoc for this feature, but not one in U-Boot itself.
Add a simple test that checks that the information comes through
correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a -u flag for U-Boot SPL which requests that unit tests be run. To
make this work, export dm_test_main() and update it to skip test features
that are not used with of-platdata.
To run the tests:
$ spl/u-boot-spl -u
U-Boot SPL 2020.10-rc5 (Oct 01 2020 - 07:35:39 -0600)
Running 0 driver model tests
Failures: 0
At present there are no SPL unit tests.
Note that there is one wrinkle with these tests. SPL has limited memory
available for allocation. Also malloc_simple does not free memory
(free() is a nop) and running tests repeatedly causes driver-model to
reinit multiple times and allocate memory. Therefore it is not possible
to run more than a few tests at a time. One solution is to increase the
amount of malloc space in sandbox_spl. This is not a problem for pytest,
since it runs each test individually, so for now this is left as is.
Signed-off-by: Simon Glass <sjg@chromium.org>
Without resizing the SDL window showed by
./u-boot -D -l
is not legible on a high resolution screen.
Allow resizing the window
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Armada 8k: Add NAND support via PXA3xx NAND driver (Baruch)
- Armada 8k: Use ATF serdes init instead of the "old" U-Boot version
(Baruch)
- Minor update to Octeon TX/TX2 defconfig (Stefan)
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX5rH/QAKCRDKSWXLKUoM
IRPAAJ9SvHR3w1qTc5W+Q5CWBUH5wJbNYQCaA4PpqZCdvyu1+nF5luL6JHhbDgw=
=hOd7
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01-v2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.01-v2
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
Move board_fit_config_name_match() from Zynq/ZynqMP to common location.
This change will open a way to use it also by Microblaze and Versal.
Through this function there is a way to handle images with multiple DTBs.
For now match it with DEVICE_TREE as is done for Zynq.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Align node properties to kernel dts node.
The change of compatible property does not affect any currently
supported board.
Keep U-Boot specific nand-enable-arbiter, and num-cs for compatibility
with the current driver.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Align node properties to kernel dts node.
Keep U-Boot specific nand-enable-arbiter, and num-cs for compatibility
with the current driver.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Shmuel Hazan <shmuel.h@siklu.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Provide tests to check the behavior of the multiplexer framework.
Two sets of tests are added. One is using an emulated multiplexer driver
that can be used to test basic functionality like select, deselect, etc.
The other is using the mmio mux which adds tests specific to it.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For zynqmp qspi, frequencies up to 40MHz will work irrespective
of feedback clock enabled or disabled. If we want higher than
40Mhz the feedback clock should be enabled.
With spi-max-frequency 108MHz it is not working when the feedback
clock is disabled. Change it to 40MHz so that it works irrespective
of feedback clock enabled or disabled.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for SHA3 command. It takes data blob
as input and generates 48 bytes sha3 hash value.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for RSA command, performs RSA encrypt &
RSA decrypt on data blob of key size.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for encryption and decryption on a given data
blob using different key sources such as userkey(KUP), device key and
PUF key. Inorder to support this a new zynqmp command(zynqmp aes) has
been introduced.
Command:
zynqmp aes srcaddr ivaddr len aesop keysrc dstaddr [keyaddr]\n"
Encrypts or decrypts blob of data at src address and puts it\n"
back to dstaddr using key and iv at keyaddr and ivaddr\n"
respectively. keysrc values specifies from which source key\n"
has to be used, it can be User/Device/PUF key. A value of 0\n"
for KUP(user key),1 for DeviceKey and 2 for PUF key. The\n"
aesop value would specify the operationwhich can be 0 for\n"
decrypt and 1 for encrypt(1) operation\n";
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mini u-boot eMMC dt parameters are not in sync with full u-boot dt.
Frequency for eMMC is fixed to 25Mhz. Due to this, mmc multi-block write
commands are failing. Increase frequency to 200Mhz to fix this issue.
Add bus-width = <8>, non-removable and disable-wp properties to the node
as this is eMMC.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable SPI drivers and driver model for microblaze.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Adding Z-turn board V5 to resolve the change between:
"Z-TURNBOARD_schematic.pdf" schematics state version 1 to 4 has Atheros AR8035
"Z-Turn_Board_sch_V15_20160303.pdf" schematics state version 5 has Micrel KSZ9031
At this time the S25FL128SAGNFI003 doesn't work because of bug:
*** Warning - spi_flash_probe_bus_cs() failed, using default environment
zynq-zturn was checked on V5 board, same error.
Maybe Z-turn board have the same problem (board with W25Q128BVFIG).
Signed-off-by: Alexandre GRIVEAUX <agriveaux@deutnet.info>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Implement early init by calling generic board_init_f_alloc_reserve and
board_init_f_init_reserve functions:
* drop SYS_MALLOC_F_LEN related code, as allocation and gd->malloc_base
assignment are taken care of by the generic functions
* drop _gd logic
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Currently, the exceptions setup code is duplicated in pre-relocation and
post-relocation init. Factor out this code to __setup_exceptions asm
routine to get rid of the duplication.
__setup_exceptions is called with a relocation offset parameter (r5)
which is set to zero for pre-reloc init and gd->reloc_off for post-reloc
exception setup.
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Half of this driver is a DM-based timer driver, and half is RISC-V-specific
IPI code. Move the timer portions in with the other timer drivers. The
KConfig is not moved, since it also enables IPIs. It could also be split
into two configs, but no boards use the timer but not the IPI atm, so I
haven't split it.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Rick Chen <rick@andestech.com>
This matches the naming scheme of other timer drivers.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Rick Chen <rick@andestech.com>
This is a regular timer driver, and should live with the other timer
drivers.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Rick Chen <rick@andestech.com>
Although the max DMA size supported by the hardware register is 22 bits (or
4M), the Linux driver for this device only supports transfers of up to 2M.
On a device with 8M total memory, I don't think it will make too much of a
difference.
Reported-by: Damien Le Moal <Damien.LeMoal@wdc.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
It is unsafe to enable OF_BOARD_FIXUP only based on OF_SEPARATE.
OF_SEPARATE may indicate that the user wishes U-Boot to use a different
device tree than one obtained via OF_PRIOR_STAGE. However, OF_SEPARATE may
also indicate that the device tree which would be obtained via
OF_PRIOR_STAGE is invalid, nonexistant, or otherwise unusable. In this
latter case, enabling OF_BOARD_FIXUP will result in corruption of the
device tree. To remedy this, only enable OF_BOARD_FIXUP if U-Boot is
configured for S-Mode.
Fixes: 1c17e55594
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Liang <ycliang@andestech.com>
On all newer Layerscape SoCs, only the export-controlled ciphers of the
crypto module are disabled on non-E parts. Thus it doesn't make sense to
completely remove the node. Linux will figure out what is there and what
is not.
Just remove it for older SoCs, where the module is indeed completely
disabled on non-E parts.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add basic support for the Kontron SMARC-sAL28 board. This includes just
the bare minimum to be able to bring up the board and boot linux.
For now, the Single and Dual PHY variant is supported. Other variants
will fall back to the basic variant.
In particular, there is no watchdog support for now. This means that you
have to disable the default watchdog, otherwise you'll end up in the
recovery bootloader. See the board README for details.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As per hardware documentation, ECx_PMUX has precedence
over SerDes protocol.
For LX2160/LX2162 if DPMACs 17 and 18 are enabled as SGMII
through SerDes protocol but ECx_PMUX configured them as RGMII,
then the ports will be configured as RGMII and not SGMII.
Signed-off-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
In the current implementation, u-boot creates iommu mappings only
for PCI devices enumarated at boot time thus does not take into
account more dynamic scenarios such as SR-IOV or PCI hot-plug.
Add an u-boot env var and a device tree property (to be used for
example in more static scenarios such as hardwired PCI endpoints
that get initialized later in the system setup) that would allow
two things:
- for a SRIOV capable PCI EP identified by its B.D.F specify
the maximum number of VFs that will ever be created for it
- for hot-plug case, specify the B.D.F with which the device
will show up on the PCI bus
More details can be found in the included documentation:
arch/arm/cpu/armv8/fsl-layerscape/doc/README.pci_iommu_extra
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This new function, xen_debug_putc(), is intended to be used to
enable CONFIG_DEBUG_UART on xen guest.
Please note that the underlying functionality in Xen is available
only when Xen is configured with !NDEBUG but is much simpler than
a generic HYPERVISOR_console_io().
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The System Control Unit (SCU) controller of Aspeed
SoCs provides the reset control for each peripheral.
This patch refactors the reset method to leverage
the SCU reset control. Thus the driver dependency
on watchdog including dedicated WDT API and reset
flag encoding can be eliminated.
The Kconfig description is also updated accordingly.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Since we now have the driver for Qualcomm PRNG HW, lets use it and add the necessary clocks and nodes.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Lets add the necessary DTS node and pinctrl properties for newly added MDIO driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Since we have SPI driver for IPQ40xx QUP SPI controller, lets add the necessary nodes, pinctrl and clocks.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
As the ownership is now Hitachi Power Grids, change the license string
and adapt the compatible string in DTS files. For kmeter1.dts we
change it to "keymile,KMETER1" for now, as this is then compliant with
what is submitted to the linux kernel. All other boards don't have
a upstreamed version in linux mainline.
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
CC: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
CC: Heiko Schocher <hs@denx.de>
CC: Marek Vasut <marex@denx.de>
CC: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
No timer drivers return an error from get_count. Instead of possibly
returning an error, just return the count directly.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Fix stm32prog command: parsing of FlashLayout without partition
- Update MAINTAINERS for ARM STM STM32MP
- Manage eth1addr on dh board with KS8851
- Limit size of cacheable DDR in pre-reloc stage in stm32mp1
- Use mmc_of_parse() to read host capabilities in mmc:sdmmc2 driver
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl+QXvgACgkQ4rK92eCq
k3Vbrgf/cBKPY9bS+lJVARgjDvIOdcXzpgH/F7dUlq+dzu/mCwhIBVKxM7/nXh5p
RhfGET2fpMYY/41LkKza7AqOiGTXZG4pTmCGe1UHXrXeIPjinWG1LQjU/KOk6U4n
681P9BZfTUXrVgzLBIUY1KBFVyMaiYfVjxU3MnA1vqrubymFbf+IpUt3OIegUDCp
AjrTdj7sFEQ3nG/pgTyqFCwkl/MG53aB9MiaBBRxeGHYnDn0qzAEHSGqzSZZGhNl
1ubJDF3K7w6Pj3MzIeA80M5r0fJoTy/qWcNH31psOpyQaHJ9NbPGjFYE6AkDPV4l
27QN71AcRtCzlv1XQpblA98pa1bUYw==
=Bl3G
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20201021' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Activate CMD_EXPORTENV/CMD_IMPORTENV/CMD_ELF for STM32MP15 defconfig
- Fix stm32prog command: parsing of FlashLayout without partition
- Update MAINTAINERS for ARM STM STM32MP
- Manage eth1addr on dh board with KS8851
- Limit size of cacheable DDR in pre-reloc stage in stm32mp1
- Use mmc_of_parse() to read host capabilities in mmc:sdmmc2 driver
Allwinner sun50i SoCs contain an OpenRISC 1000 CPU that functions as a
System Control Processor, or SCP. ARM Trusted Firmware (ATF)
communicates with the SCP over SCPI to implement the PSCI system
suspend, shutdown and reset functionality. Currently, SCP firmware is
optional; the system will boot and run without it, but system suspend
will be unavailable.
Since all communication with the SCP is mediated by ATF, the only thing
U-Boot needs to do is load the firmware into SRAM. The SCP firmware
occupies the last 16KiB of SRAM A2, immediately following ATF.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Since commit d879616e9e ("spl: fit: simplify logic for FDT loading for
non-OS boots"), the SPL looks at the "os" properties of FIT images to
determine where to append the FDT.
The "os" property of the "firmware" image also determines how to execute
the next stage of the boot process, as in 1d3790905d ("spl: atf:
introduce spl_invoke_atf and make bl31_entry private"). For this reason,
the next stage must be specified in "firmware", not in "loadables".
To support this additional functionality, and to properly model the boot
process, where ATF runs before U-Boot, add the "os" properties and swap
the firmware/loadable images in the FIT image.
Since this description was copied as an example in commit 70248d6a2916
("binman: Support generating FITs with multiple dtbs"), update those
examples as well for correctness and consistency.
Acked-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This consolidates the SoC-specific part at the top of the file to avoid
cluttering it up with preprocessor conditions.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Prior to commit 7f7f8aca8257 ("sunxi: Convert 64-bit boards to use
binman"), if the BL31 environment variable was not defined, the firmware
would be loaded from a file "bl31.bin" in the current directory. Restore
that behavior by providing that as the default filename in case no entry
arg is provided, which will be the case if the environment variable is
unset.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Nodes should have a blank line separating them from sibling nodes and
properties. Add the necessary lines.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Previously, because we have no source code about the DRAM initialization
of V3s and missing some configurations (delays and MBUS QoS info), our
V3s DRAM initialization sequence is hacked from the H3 one.
As the SDK shipped with PineCube contains source code for V3s libdram,
we can retrieve these information from it and tweak some other magic
bits.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
When partitions are not available on a device the command stm32prog raises
an error but a device can have no partition to check in init_device()
and the command need to continue to the next part_id.
This patch correct an issue for ram0 target, when block_dev and mtd
are NULL.
For example with the simple flashlayout file:
Opt Part Name Type Device Offset Binary
- 0x01 fsbl Binary none 0x0 tf-a-serialboot.stm32
- 0x03 ssbl Binary none 0x0 u-boot.stm32
P 0x10 kernel System ram0 0xC2000000 uImage.bin
P 0x11 dtb FileSytem ram0 0xC4000000 stm32mp157f-ev1.dtb
Fixes: ffc405e63b ("stm32mp: stm32prog: add upport of partial update")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Cosmetic update of gpio.h:
- remove enumerate: stm32_gpio_port, stm32_gpio_pin
because STM32_GPIO_XXX values are unused
- move STM32_GPIOS_PER_BANK in stm32_gpio.c
as its value is IP dependent and not arch dependent
No functional change as number of banks and number of gpio by banks
is managed by device tree since since DM migration and
commit 8f651ca60b ("pinctrl: stm32: Add get_pins_count() ops").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
In pre-reloc stage, U-Boot marks cacheable the DDR limited by
the new config CONFIG_DDR_CACHEABLE_SIZE.
This patch allows to avoid any speculative access to DDR protected by
firewall and used by OP-TEE; the "no-map" reserved memory
node in DT are assumed after this limit:
STM32_DDR_BASE + DDR_CACHEABLE_SIZE.
Without security, in basic boot, the value is equal to STM32_DDR_SIZE.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
An earlier conversion from struct to defines introduced two errors, both
related to setup of EMAC routed via the FPGA. One of the offsets was
incorrect, and the EMAC0/EMAC1 were swapped.
The effect of this was rather odd: both ports could operate at gigabit,
but one of them would fail to transmit when operating at 100Mbit.
Fixes: db5741f7a8 ("arm: socfpga: Convert system manager from struct to defines")
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
This sync's the RZ/G2H clock tables with mainline linux 5.9 commit
bbf5c979011a ("Linux 5.9").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
This sync's the RZ/G2N clock tables with mainline linux 5.9 commit
bbf5c979011a ("Linux 5.9").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Add config support for RZ/G2H(a.k.a R8A774E1) SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Add config support for RZ/G2N(a.k.a R8A774B1) SoC.
Also fixed the alignment issue on R8A774A1 config.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Use slow clock CCF compatible DT bindings. This will not break
the above functionality as the SoC is not booting with current
PMC bindings.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Clock support is needed for all Octeon TX/TX2 boards. This patch selects
CONFIG_CLK so that it is available.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Suneel Garapati <sgarapati@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
- fsl_esdhc_imx cleanup
- not send cm13 if send_status is 0.
- Add reinit API
- Add mmc HS400 for fsl_esdhc
- Several cleanup for fsl_esdhc
- Add ADMA2 for sdhci
- Octeon TX: Add NAND driver (Suneel)
- Octeon TX: Add NIC driver driver (Suneel)
- Octeon TX2: Add NIC driver driver (Suneel)
- Armada 8040: Add iEi Puzzle-M80 board support (Luka)
- Armada A37xx SPI: Add support for CS-GPIO (George)
- Espressobin: Use Linux model/compatible strings (Andre)
- Espressobin: Add armada-3720-espressobin-emmc.dts from Linux (Andre)
- Armada A37xx: Small cleanup of config header (Pali)
The EFI_RNG_PROTOCOL is needed for address randomization in Linux.
We should provide it by default on QEMU.
Reported-by: François Ozog <francois.ozog@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Using different strings for the device tree node labels and the label
property of buttons sharpens the button label unit test.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Import armada-3720-espressobin-emmc.dts from Linux, but use sdhc1 for
emmc, since our dtsi is still based on downstream and sdhc0 is used for
the sd card.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Move most of the dts to the new common armada-3720-espressobin.dtsi
file, just like Linux, but keep the current, downstream based, version.
The dts itself is imported from Linux.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Fix the actual board vendor and ease synching dts files from Linux.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add initial U-Boot support for the iEi Puzzle-M801 board based on the
Marvell Armada 88F8040 SoC.
Currently supported hardware:
1x USB 3.0
4x Gigabit Ethernet
2x SFP+ (with NXP PCA9555 and NXP PCA9544)
1x SATA 3.0
1x M.2 type B
1x RJ45 UART
1x SPI flash
1x EPSON RX8010 RTC
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Add properties related to eMMC HS400 mode.
mmc-hs400-1_8v;
bus-width = <8>;
They had been already in kernel dts file since the first
lx2160ardb dts patch.
b068890 arm64: dts: add LX2160ARDB board support
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Move to use generic handoff dtsi (socfpga_arria10-handoff.dtsi) and include
the specify generated _handoff.h header file from qts-filter-a10.sh script.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add a script to process HPS handoff data and generate a header
for inclusion in u-boot specific devicetree addons. The header
should be included in the top level of u-boot.dtsi.
Signed-off-by: Dalon Westergreen <dalon.westergreen@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Resend mailbox command for 3 times with 2ms interval in between if
it receives MBOX_RESP_TIMEOUT and MBOX_RESP_DEVICE_BUSY response code.
Add a wrapper function mbox_send_cmd_common_retry() for retry, change
all the callers to use this wrapper function.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Sync latest mailbox response codes from SDM firmware.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Mailbox command which is too large to fit into the mailbox
FIFO command buffer can be sent to SDM in multiple parts.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Mailbox driver should always check for the length of the response
and read the response data before returning the response status to
caller.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add miliseconds delay when waiting for mailbox event to happen
before timeout. This will ensure the timeout duration is predictive.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Document down the usage of boot_scratch_cold register to avoid
overlapping of usage in the code for S10 & Agilex.
The boot_scratch_cold register is generally used for passing
critical system info between SPL, U-Boot and Linux.
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Enable FPGA full reconfiguration support with Intel FPGA SDM
Mailbox driver for Agilex.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Rename Stratix10 FPGA driver to Intel FPGA SDM Mailbox driver
because it is using generic SDM (Secure Device Manager) Mailbox
interface shared by other platform (e.g. Agilex) as well.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
All SoCFPGA platforms (except Cyclone V) are now switching
to CONFIG_WDT (driver model for watchdog timer drivers)
from CONFIG_HW_WATCHDOG.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Print reset state (warm/cold) together with the
source (watchdog/MPU) which has triggered the warm
reset on S10 & Agilex.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Include SDM triggered warm reset bit (BIT1) in Reset Manager's stat
register when checking for HPS warm reset status.
Refactor the warm reset mask macro for clarity purpose.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Rename the driver from S10 to SoC64 because Intel Agilex platform
also using the this SYSRESET SoCFPGA driver for S10.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Timer only need to be initialized once in SPL.
This patch remove the redundancy of initializing the
timer again in U-Boot proper
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
'dwmac_socfpga' driver will setup the PHY interface during probe.
PHY interface setup in arch_misc_init() is no longer needed.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Now that PIE works when U-Boot is started from ROM, let's enable
CONFIG_POSITION_INDEPENDENT, which allows to load U-Boot also via
ARM Trusted-Firmware's fip.bin to DRAM, without tweaking the
configuration.
To get a writable initial stack, we need to keep the fixed initial
stack pointer, which points to DRAM in our case.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
CONFIG_ARCH_SUPPORT_TFABOOT was used on the qemu-arm64 platform to
guard a tweak to the flash bank configuration. U-Boot now reads the
current flash setup from the devicetree, so there is no need for
this option anymore.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently selecting CONFIG_POSITION_INDEPENDENT also forces us to use an
initial stack pointer relative to the beginning of the BSS section.
This makes some sense, because this should be writable memory anyway.
However the BSS section is not cleared or used until later in the
setup process (after relocation), so memory nearby might not be
available early enough to host the initial stack. This is an issue if
U-Boot is loaded from (Flash-)ROM, for instance.
Allow CONFIG_INIT_SP_RELATIVE to be turned off by a board's config, to
be able to select a fixed stack pointer, for instance in known good
DRAM.
This will help QEMU utilising PIE, when it's loaded to (Flash-)ROM.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
When the actual offset between link and runtime address is zero, there
is no need for patching up U-Boot early when running with
CONFIG_POSITION_INDEPENDENT.
Skip the whole routine when the distance is 0.
This helps when U-Boot is loaded into ROM, or in otherwise sensitive
memory locations.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
When we build an arm64 target and enable POSITION_INDEPENDENT, we were
skipping our build-time dynamic relocation fixup routine (STATIC_RELA).
This was probably done because we didn't need it in this case, as the
PIE fixup routine in start.S would take care of that at runtime.
However when we now skip this routine (upon detecting that the fixup
offset is 0), this might lead to uninitialised pointers.
Remove the exception, so that we always do the build-time relocation.
NOTE: GNU binutils starting with v2.27.1 do this build-time relocation
automatically, to be in-line with other architecures. So on newer
toolchains our manual fixup is actually not needed. It doesn't hurt to
have it, though, so that we keep compatibility with the popular Linaro
toolchains, which lack this feature.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
The CONFIG_TFABOOT option is more about what U-Boot DOES NOT need to do
than to support some features.
Explain a bit more in the Kconfig help text to avoid misunderstandings.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a device tree binding for the BOOT button on the Maix board.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This patch adds the necessary device tree bindings.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Rick Chen <rick@andestech.com>
This modifies the existing led test to check for default led naming as
added in the previous patch.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This extends the pinctrl-sandbox driver to support pin muxing, and adds a
test for that behaviour. The test is done in C and not python (like the
existing tests for the pinctrl uclass) because it needs to call
pinctrl_select_state. Another option could be to add a command that
invokes pinctrl_select_state and then test everything in
test/py/tests/test_pinmux.py.
The pinctrl-sandbox driver now mimics the way that many pinmux devices
work. There are two groups of pins which are muxed together, as well as
four pins which are muxed individually. I have tried to test all normal
paths. However, very few error cases are explicitly checked for.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
to improve the maintainability. It is more easier to modify and add
configurations of the driver in the centralized ram driver directory.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
- mips: octeon: add support for DWC3 USB
- mips: octeon: add support for booting Linux
-----BEGIN PGP SIGNATURE-----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=v+p3
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-10-07' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips
- mips: octeon: add support for DDR4 memory controller
- mips: octeon: add support for DWC3 USB
- mips: octeon: add support for booting Linux
Octeon needs a platform specific cmd to boot the Linux kernel, as
specific parameters need to be passed and special handling for the
multiple cores (SMP) is needed.
Co-developed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
[use gd->ram_base instead of gd->bd->bi_memstart]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This is needed for Linux booting, as the memory infos need to be passed
in this bootmem format to the Linux kernel.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add header to handle bootinfo support, needed for Octeon Linux kernel
booting.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This header includes the Octeon feature detection used in many Octeon
drivers.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This header includes common register defines and accessor functions.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the necessary lowlevel init code, to enable SMP Linux
booting. This code will be used with the platform specific Octeon Linux
boot command "bootoctlinux", which starts a configurable number of cores
into Linux.
Additionally some erratas and lowlevel register initializations are
copied from the original Cavium / Marvell U-Boot source code, enabling
booting into the Linux kernel.
Signed-off-by: Stefan Roese <sr@denx.de>
As noticed while working on the USB xHCI support, Octeon needs to flush
all pending writes so that the values are present in the memory. Add
this "syncw" instruction (twice) to flush_dcache_range().
Signed-off-by: Stefan Roese <sr@denx.de>
Import platform specific mangle-port.h header, allowing a area specific
swapping, which is needed on Octeon for USB & PCI areas.
Imported from Linux v5.7.
Signed-off-by: Stefan Roese <sr@denx.de>
Import octeon_should_swizzle_table[] which is needed for the area
specific swapping. It will be used by the platform specific
mangle-port.h header.
Imported from Linux v5.7.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the initialization call for the Octeon RAM driver to
the Octeon platforms code. So if enabled via Kconfig, the DDR driver
will be called and the RAM will be configured and used. If the RAM
driver is not enabled, the L2 cache is still used as RAM.
Signed-off-by: Stefan Roese <sr@denx.de>
This header will be used by the DDR driver (lmc). Its ported from the
2013 Cavium / Marvell U-Boot repository.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This header will be used by the DDR driver (lmc). Its ported from the
2013 Cavium / Marvell U-Boot repository.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This header is used by the upcoming DDR driver and potentially by other
drivers ported from the 2013 Cavium / Marvell U-Boot repository.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the memory controller (LMC) DT node to the Octeon 3 dtsi
file. It also adds the L2C DT node, as this is referenced by the DDR
driver.
Signed-off-by: Stefan Roese <sr@denx.de>
When using SDL for input the SDL key codes are first converted to Linux key
codes and then to matrix entries of the cross wired keyboard.
We must not map any key code to two different places on the keyboard. So
comment out one backslash position.
Update the rest of the file from Linux 5.7.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some blobs need a larger alignment than the default. For example, ACPI
tables often start at a 4KB boundary. Add support for this.
Update the size of the test blob to allow these larger records.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
-----BEGIN PGP SIGNATURE-----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=rbAX
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20201005' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- generate unique mac address from SoC serial on S400 board
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
This imports the G12A & SM1 SoC and boards DT changes from the Linux
commit 9123e3a74ec7 ("Linux 5.9-rc1").
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the correcly architectured USB Glue node for Meson AXG and the
S400 board in -u-boot.dtsi until support in upstream Linux then
backported.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the board_usb_init()/cleanup() for USB gadget for AXG based
on the code for the G12A architecture.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The registers which are managed by the meson-gxl-usb3 PHY driver are
actually "USB control" registers (which are "glue" registers which
manage OTG detection and routing of the OTG capable port between the
DWC2 peripheral-only controller and the DWC3 host-only controller).
Drop the meson-gxl-usb3 PHY driver now that the dwc3-meson-gxl-usb
driver supports the USB control registers on GXL and GXM SoCs (these
were previously managed by the meson-gxl-usb3 PHY driver).
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The USB support was initialy done with a set of PHYs and dwc3-of-simple
because the architecture of the USB complex was not understood correctly
at the time (and proper documentation was missing...).
But with the G12A family, the USB complex was correctly understood and
implemented correctly.
This adds a proper driver for the glue, based on the G12A one, but with
enough changes to require a different driver in U-Boot.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This imports the AXG, GXL & GXM SoC and boards DT changes from the Linux
commit b3a9e3b9622a ("Linux 5.8-rc1").
This change also removes GXL & GXM u-boot.dtsi hacks for USB gadget.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl960JkcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDaWCACYjvloDzXQaYaauWwR
whFwgkUAQ8yjadj/12We/X2b7HGisNFNE80e/V4MU8RrJDFZmohZdLWMfRKez29X
d+BG+OzVXxHWozny7ZQ2g1yYJbgCI7sVUeemQjUBZJ6aKPneQlVfwyfT2l88wOVK
yQMqS+ZyVogihR9/NHCOlJHog+6OOoBmc16w1tymM6QcO8ZsYeA66ed8SLnjDb3N
Rg2Ll2RR/lHuD/Fpxt1aUhybXFKSIOr4Qopo5X0hw5B3ibkp6JXGRE2wIwQYw6CA
q+sKTg37CSzylipkQ5EOGdLcXD7r3KIGkSbUMb8wvt6dROarnIuQ+zJeF3sr+l2H
hSoU
=vHqZ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for 2021.01 cycle:
This feature set includes a new CPU driver for at91 family, new driver
for PIT64B hardware timer, support for new at91 family SoC named sama7g5
which adds: clock support, including conversion of the clock tree to
CCF; SoC support in mach-at91, pinctrl and mmc drivers update. The
feature set also includes updates for mmc driver and some other minor
fixes and features regarding building without the old Atmel PIT and the
possibility to read a secondary MAC address from a second i2c EEPROM.
DT alignment with Linux kernel v5.9-rc4 for the STM32MP15x soc
device tree files and the STMicroelectronics boards device tree files.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The u-boot,dm-spl DT props are missing on AV96, hence the pinmux and
flash0 nodes are not included in the reduced SPL DT. This prevents
SPI NOR boot from working at all. Fix this by filling them in.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Add tests for SCMI reset controllers. A test device driver
sandbox-scmi_devices.c is used to get reset resources, allowing further
resets manipulation.
Change sandbox-smci_agent to emulate 1 reset controller exposed through
an agent. Add DM test scmi_resets to test this reset controller.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add tests for SCMI clocks. A test device driver sandbox-scmi_devices.c
is used to get clock resources, allowing further clock manipulation.
Change sandbox-smci_agent to emulate 3 clocks exposed through 2 agents.
Add DM test scmi_clocks to test these 3 clocks.
Update DM test sandbox_scmi_agent with load/remove test sequences
factorized by {load|remove}_sandbox_scmi_test_devices() helper functions.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change introduces SCMI agent uclass to interact with a firmware
using the SCMI protocols [1].
SCMI agent uclass currently supports a single method to request
processing of the SCMI message by an identified server. A SCMI message
is made of a byte payload associated to a protocol ID and a message ID,
all defined by the SCMI specification [1]. On return from process_msg()
method, the caller gets the service response.
SCMI agent uclass defines a post bind generic sequence for all devices.
The sequence binds all the SCMI protocols listed in the FDT for that
SCMI agent device. Currently none, but later change will introduce
protocols.
This change implements a simple sandbox device for the SCMI agent uclass.
The sandbox nicely answers SCMI_NOT_SUPPORTED to SCMI messages.
To prepare for further test support, the sandbox exposes a architecture
function for test application to read the sandbox emulated devices state.
Currently supports 2 SCMI agents, identified by an ID in the FDT device
name. The simplistic DM test does nothing yet.
SCMI agent uclass is designed for platforms that embed a SCMI server in
a firmware hosted somewhere, for example in a companion co-processor or
in the secure world of the executing processor. SCMI protocols allow an
SCMI agent to discover and access external resources as clock, reset
controllers and more. SCMI agent and server communicate following the
SCMI specification [1]. This SCMI agent implementation complies with
the DT bindings defined in the Linux kernel source tree regarding
SCMI agent description since v5.8.
Links: [1] https://developer.arm.com/architectures/system-architectures/software-standards/scmi
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The tests rely on a dummy driver to allocate and initialize the regmaps
and the regmap fields using the managed API. The first test checks if
the regmap config fields like width, reg_offset_shift, range specifiers,
etc work. The second test checks if regmap fields behave properly (mask
and shift are ok) by peeking into the regmap.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a test to verify that GPIOs can be acquired/released using the managed
API. Also check that the GPIOs are released when the consumer device is
removed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
The tests are basically the same as for the regular API. Except that
the reset are initialized using the managed API, and no freed manually.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
This adds comments regarding the ordering and purpose of certain
instructions as I understand them.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Liang <ycliang@andestech.com>
This ensures constructs like `if (gd & gd->...) { ... }` work when
accessing the global data pointer. Without this change, it was possible for
a very early trap to cause _exit_trap to directly or indirectly (through
printf) to read arbitrary memory. This could cause a second trap,
preventing show_regs from being printed.
printf (and specifically puts) uses gd to determine what function to print
with. These functions in turn use gd to find the serial device, etc.
However, before accessing gd, puts first checks to see if it is non-NULL.
This indicates an existing (perhaps undocumented) assumption that either gd
is NULL or it is completely valid.
Before this patch, gd either points to unexpected data (because it retains
the value it did from the prior-stage) or points to uninitialized data
(because it has not yet been initialized by board_init_f_init_reserve)
until the hart has acquired available_harts_lock. This can cause two
problems, depending on the value of gd->flags. If GD_FLG_SERIAL_READY is
unset, then some garbage data will be printed to stdout, but there will not
be a second trap. However, if GD_FLG_SERIAL_READY is set, then puts will
try to print with serial_puts, which will likely cause a second trap.
After this patch, gd is zero up until either a hart has set it in
wait_for_gd_init, or until it is set by arch_init_gd. This prevents its
usage before its data is initialized because both handle_trap and puts
ensure that gd is nonzero before using it. After gd has been set, it is OK
to access it because its data has been cleared (and so flags is valid).
XIP cannot use locks because flash is not writable. This leaves it
vulnerable to the same class of bugs regarding already-pending IPIs as
before this series. Fixing that would require finding another method of
synchronization, which is outside the scope of this series.
Fixes: 7c6ca03eae ("riscv: additional crash information")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
We can reduce the number of instructions needed to use available_harts_lock
by using the aq and rl suffixes for AMOs.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Even though we no longer call smp_function if an IPI was not sent by
U-Boot, we still need to clear any IPIs which were pending from the
execution environment. Otherwise, secondary harts will busy-wait in
secondary_hart_loop, instead of relaxing.
Along with the previous commit ("riscv: Use a valid bit to ignore
already-pending IPIs"), this fixes SMP booting on the Kendryte K210.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Some IPIs may already be pending when U-Boot is started. This could be a
problem if a secondary hart tries to handle an IPI before the boot hart has
initialized the IPI device.
To be specific, the Kendryte K210 ROM-based bootloader does not clear IPIs
before passing control to U-Boot. Without this patch, the secondary hart
jumps to address 0x0 as soon as it enters secondary_hart_loop, and then
hangs in its trap handler.
This commit introduces a valid bit so secondary harts know when and IPI
originates from U-Boot, and it is safe to use the IPI API. The valid bit is
initialized to 0 by board_init_f_init_reserve. Before this, secondary harts
wait in wait_for_gd_init.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Liang <ycliang@andestech.com>
Without a matching barrier on the write side, the barrier in handle_ipi
does nothing. It was entirely possible for the boot hart to write to addr,
arg0, and arg1 *after* sending the IPI, because there was no barrier on the
sending side.
Fixes: 90ae281437 ("riscv: add option to wait for ack from secondary harts in smp functions")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Liang <ycliang@andestech.com>
Clearing MIP.MSIP is not guaranteed to do anything by the spec. In
addition, most existing RISC-V hardware does nothing when this bit is set.
The following commits "riscv: Use a valid bit to ignore already-pending
IPIs" and "riscv: Clear pending IPIs on initialization" should implement
the original intent of the reverted commit in a more robust manner.
This reverts commit 9472630337.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
We currently do this in a u-boot specific dts, but hopefully we can get
these bindings added in Linux in the future.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@openfive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
The interrupt controller property is removed from the clint binding because
the clint is not an interrupt-controller. That is, no other devices have an
interrupt which is controlled by the clint.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
This converts the clint driver from the riscv-specific interface to be a
DM-based UCLASS_TIMER driver. In addition, the SiFive DDR driver previously
implicitly depended on the CLINT to select REGMAP.
Unlike Andes's PLMT/PLIC (which AFAIK never have anything pass it a dtb),
the SiFive CLINT is part of the device tree passed in by qemu. This device
tree doesn't have a clocks or clock-frequency property on clint, so we need
to fall back on the timebase-frequency property. Perhaps in the future we
can get a clock-frequency property added to the qemu dtb.
Unlike with the Andes PLMT, the Sifive CLINT is also an IPI controller.
RISCV_SYSCON_CLINT is retained for this purpose.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@openfive.com>
This merges the PLIC initialization code from two functions into one.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
This converts the PLMT driver from the riscv-specific timer interface to be
a DM-based UCLASS_TIMER driver.
The clock-frequency/clocks properties are preferred over timebase-frequency
for two reasons. First, properties which affect a device should be located
near its binding in the device tree. Using timebase-frequency only really
makes sense when the cpu itself is the timer device. This is the case when
we read the time from a CSR, but not when there is a separate device.
Second, it lets the device use the clock subsystem which adds flexibility.
If the device is configured for a different clock speed, the timer can
adjust itself.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
To test this function, sandbox CPU must set cpu_platdata.timebase_freq on
bind. It also needs to expose a method to set the current cpu. I also make
some most members of cpu_sandbox_ops static.
On the timer side, the device tree property
sandbox,timebase-frequency-fallback controls whether sandbox_timer_probe
falls back to time_timebase_fallback or to SANDBOX_TIMER_RATE.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The riscv-timer driver currently serves as a shim for several riscv timer
drivers. This is not too desirable because it bypasses the usual timer
selection via the driver model. There is no easy way to specify an
alternate timing driver, or have the tick rate depend on the cpu's
configured frequency. The timer drivers also do not have device structs,
and so have to rely on storing parameters in gd_t. Lastly, there is no
initialization call, so driver init is done in the same function which
reads the time. This can result in confusing error messages. To a user, it
looks like the driver failed when trying to read the time, whereas it may
have failed while initializing.
This patch removes the shim functionality from the riscv-timer driver, and
has it instead implement the former rdtime.c timer driver. This is because
existing u-boot users who pass in a device tree (e.g. qemu) do not create a
timer device for S-mode u-boot. The existing behavior of creating the
riscv-timer device in the riscv cpu driver must be kept. The actual reading
of the CSRs has been redone in the style of Linux's get_cycles64.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The following UEFI related issues are fixed:
* restore the global data pointer in the RISC-V trap handler
* install EFI_RNG_PROTOCOL only if we have a random number generator
* display human readable string for EFI_RNG_PROTOCOL in efidebug command
-----BEGIN PGP SIGNATURE-----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=W9Wz
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-10-rc6' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-10-rc6
The following UEFI related issues are fixed:
* restore the global data pointer in the RISC-V trap handler
* install EFI_RNG_PROTOCOL only if we have a random number generator
* display human readable string for EFI_RNG_PROTOCOL in efidebug command
The gp register is used to store U-Boot's global data pointer. We should
not assume that an UEFI application leaves the gp register unchanged as
the UEFI specifications does not define who is the owner of the gp and tp
registers.
So the following sequence should be followed in the trap handler:
* save the caller's gp register
* restore the global data pointer
* serve interrupts or print crash dump and reset
* restore the caller's gp register
Cc: Abner Chang <abner.chang@hpe.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Use "imply" instead of "select" for BOARD_EARLY_INIT_F config option,
and then disable it on boards which don't need it.
Updated grpeach_defconfig to disable CONFIG_BOARD_EARLY_INIT_F option for
RZA1.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Mark the default s_init function as weak, so that SoC's can
override it if needed, and it will still be discarded if unused.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Add support to identify R8A7796 r1.3 SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Enable the RPC Hyperflash driver on R8A7795,R8A7796,R8A77965
Salvator-X,ULCB and R8A77990 Ebisu. Note that to make the HF
accessible, mainline ATF is mandatory and must be built with
RCAR_RPC_HYPERFLASH_LOCKED=0 . Note that this is intended for
development and testing convenience only and must be disabled
in deployment for platform security reasons.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
- Enhance the 'zboot' command to be more like 'bootm' with sub-commands
- The last series of ACPI core changes for programmatic generation of
ACPI tables
- Add all required ACPI tables for ApolloLake and enable ACPIGEN on
Chromebook Coral
- A feature minor enhancements to the 'hob' command
- Intel edison: Support for writing an xFSTK image via binman
It is useful to be able to flash Edison directly without relying on the
installed U-Boot being functional.
Add a binman image for this. It includes a 'OSIP' header (which happens to
look like an MBR / (Master-Boot Record), U-Boot binary and an environment.
I am not able to find a specification for OSIP.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We already use binman's 'multiple-images' feature with Chrome OS and we
want to use it for Edison. There is no real down-side.
Adjust x86 to always use multiple-images.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
At present the mtrr command only support 8 MTRRs. Some SoCs have more than
that. Update the implementation to support up to 10. Read the number of
MTRRs dynamically instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
