This takes care of resetting the 32kHz square wave, which is
used by some boards as clock source for the SoC.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This driver allows to use SPI flash as backing store for
boot counter values with DM enabled.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This option is only supported by the IMX watchdog and seems to be
similar to CONFIG_WATCHDOG.
Move it below the IMX watchdog and make it dependent on IMX_WATCHDOG.
Signed-off-by: Michael Walle <michael@walle.cc>
commit c05ed00afb dropped linux/delay.h from common header
add linux/delay.h to avoid compile warning here
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
- New PX30 board: Engicam PX30.Core;
- Fix USB HID support for rock960;
- Remove host endianness dependency for rockchip mkimage;
- dts update for rk3288-tinker;
- Enable console MUX for some ROCKPi boards;
- Add config-based ddr selection for px30;
Like, rk3399 the rk3288 also supports 4K resolution.
So, enable it for rk3288 with HDMI platforms.
Right now, rockchip video drivers are supporting for rk3288,
rk3399 SoC families, so mark the 4K resolution by default
if it's an HDMI video out.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
This function is a variant of dfu_write_by_name() and takes a DFU alt
setting number for dfu configuration.
It will be utilised to implement UEFI capsule management protocol for
raw image in a later commit.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This variable will be utilized to enumerate all dfu entities
for UEFI capsule firmware update in a later commit.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The main purpose of this patch is to separate a generic interface for
updating firmware using DFU drivers from "auto-update" via tftp.
This function will also be used in implementing UEFI capsule update
in a later commit.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The range of an addressable pointer can go beyond 'integer'.
So change the argument type to a void pointer.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function is essentially independent from tftp, and will also be
utilised in implementing UEFI capsule update in a later commit.
So just give it a more generic name.
In addition, a new configuration option, CONFIG_DFU_WRITE_ALT, was
introduced so that the file will be compiled with different options,
particularly one added in a later commit.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Up to now the emulated RTC is initialized using the U-Boot build time.
With this patch the environment variable 'rtc_emul_epoch' can be used to
provide a better initial time. The variable is a decimal string with
the number of seconds since 1970-01-01. Here is an example where the RTC
had not been probed yet:
=> setenv rtc_emul_epoch 1610109000
=> date
Date: 2021-01-08 (Friday) Time: 12:30:00
If the variable does not exist, the U-Boot build time is used as fallback.
The environment variable may be set when shutting down the operating system
if the U-Boot environment is exposed to the OS (cf. ENV_IS_IN_FAT and
ENV_IS_IN_EXT4).
Suggested-by: Pablo Sebastián Greco <pgreco@centosproject.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently the emulated RTC is initialized in the emul_rtc_get() get
function. This does not match the design of the driver model.
Move the initialization of the emulated RTC to the probe() function.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Found this by comparing it to the coreboot driver, a form of this call
was introduced there in their commit b9a7877568cf ("rockchip/*: refactor
edp driver"). This is copy-pasted from U-Boot's link_train_cr() slightly
above it.
Without this on a gru-kevin chromebook, I have:
clock recovery at voltage 0 pre-emphasis 0
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
channel eq failed, ret=-5
link train failed!
rk_vop_probe() Device failed: ret=-5
With this, it looks like training succeeds:
clock recovery at voltage 0 pre-emphasis 0
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 6dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 6dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 6dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 6dB
using signal parameters: voltage 0.4V pre_emph 6dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 0dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 0dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 0dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 0dB
using signal parameters: voltage 0.4V pre_emph 0dB
channel eq at voltage 0 pre-emphasis 0
config video failed
rk_vop_probe() Device failed: ret=-110
The "config video failed" error also goes away when I disable higher
log levels, and it claims to have successfully probed the device.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
The SRAM on the PX30 is not big enough to hold multiple DDR configs
so it needs to be selected during build.
So far simply the DDR3 config was always selected and getting DDR4
or LPDDR2/3 initialized would require a code modification.
So add Kconfig options similar to RK3399 to allow selecting the DDR4
and LPDDR2/3 options instead, while DDR3 stays the default as before.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
In order to correctly calculate the designware watchdog
timeouts, the watchdog clock is required. Implement required
clocks to facilitate this.
Signed-off-by: Jack Mitchell <ml@embed.me.uk>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
At present we use a 'node' pointer in the of-platadata phandle_n_arg
structs. This is a pointer to the struct driver_info for a particular
device, and we can use it to obtain the struct udevice pointer itself.
Since we don't know the struct udevice pointer until it is allocated in
memory, we have to fix up the phandle_n_arg.node at runtime. This is
annoying since it requires that SPL's data is writable and adds a small
amount of extra (generated) code in the dm_populate_phandle_data()
function.
Now that we can find a driver_info by its index, it is easier to put the
index in the phandle_n_arg structures.
Update dtoc to do this, add a new device_get_by_driver_info_idx() to look
up a device by drive_info index and update the tests to match.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that parent devices are supported with of-platadata, we don't need the
messy code to fix up the parent pointers and allocations on Apollo Lake.
Put the code behind a condition.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present, enabling CONFIG_APL_SPI_FLASH_BOOT does not build since SPI
and SPI flash are not enabled for TPL. Add a condition to fix this and
tidy up a build warning in the SPI-flash driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a simple test that we can obtain the correct parent for an I2C
device. This requires updating the driver names to match the compatible
strings, adding them to the devicetree and enabling a few options.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present of-platdata does not provide parent information. But this is
useful for I2C devices, for example, since it allows them to determine
which bus they are on.
Add support for setting the parent correctly, by storing the parent
driver_info index in dtoc and reading this in lists_bind_drivers(). This
needs multiple passes since we must process children after their parents
already have been bound.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no devicetree with of-platdata. Update a few uclasses to allow
them to be built for sandbox_spl. Also drop the i2c-gpio from SPL to avoid
build errors, since it does not support of-platdata.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we update the driver_info struct with a pointer to the device
that it created (i.e. caused to be bound). This works fine when U-Boot SPL
is stored in read-write memory. But on some platforms, such as Intel
Apollo Lake, it is not possible to update the data memory.
In any case, it is bad form to put this information in a structure that is
in the data region, since it expands the size of the binary.
Create a new driver_rt structure which holds runtime information about
drivers. Update the code to store the device pointer in this instead.
Also update the test check that this works.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have a test in dtoc for this feature, but not one in U-Boot itself.
Add a simple test that checks that the information comes through
correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
With of-platdata, the driver_info struct is updated with the device
pointer when it is bound. This makes it easy for a device to be found by
its driver info with the device_get_by_driver_info() function.
Add a test that all devices (except the root device) have such an entry.
Fix a bug that the function does not set *devp to NULL on failure, which
the documentation asserts.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this option is disabled in SPL, meaning that warnings are not
displayed. It is sometimes useful to see warnings in SPL for debugging
purposes.
Add a new Kconfig option to permit this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since sandbox's SPL is build with of-platadata, we should not use
U_BOOT_DEVICE() declarations as well. Drop them.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this option results in a number of #ifdefs due to the presence
or absence of the global_data of_root member.
Add a few macros to global_data.h to work around this. Update the code
accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Armada 8k: Add NAND support via PXA3xx NAND driver (Baruch)
- Armada 8k: Use ATF serdes init instead of the "old" U-Boot version
(Baruch)
- Minor update to Octeon TX/TX2 defconfig (Stefan)
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX5rH/QAKCRDKSWXLKUoM
IRPAAJ9SvHR3w1qTc5W+Q5CWBUH5wJbNYQCaA4PpqZCdvyu1+nF5luL6JHhbDgw=
=hOd7
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01-v2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.01-v2
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
Based on Linux kernel commit fc256f5789cb ("mtd: nand: pxa3xx: enable
NAND controller if the SoC needs it"). This commit adds support for the
Armada 8040 nand controller.
The kernel commit says this:
Marvell recent SoCs like A7k/A8k do not boot with NAND flash
controller activated by default. Enabling the controller is a matter
of writing in a system controller register that may also be used for
other NAND related choices.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Shmuel Hazan <shmuel.h@siklu.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Fix the condition to set UHS timings for speeds upto HS200.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The kfree() call is unreachable, and is not needed. Remove this call and
the fail_disable_clk label.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Use the generic DT code to find the device compatible property for us.
This makes the driver look more like other current drivers. It also make
it easier to add support for other variants like Armada 8K in a future
commit.
Signed-off-by: Shmuel Hazan <shmuel.h@siklu.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
It helps ATF to determine who called power on function (U-boot/Linux).
The corresponding ATF code was added in this commit:
mvebu: cp110: avoid pcie power on/off sequence when called from Linux
55df84f974
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Replace the comphy initialization for PCIe with appropriate SMC call, so
the firmware will perform appropriate comphy initialization.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Replace all comphy initialization with appropriate smc calls. It will
result with triggering synchronous exception that is handled by Secure
Monitor code in EL3. Then the Secure Monitor code will dispatch each smc
call (by parsing the smc function identifier) and triggers appropriate
comphy initialization.
This patch reworks serdes handling for: SATA, SGMII, HS-SGMII and SFI
interfaces.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
This adds a driver for mmio-based syscon multiplexers controlled by
bitfields in a syscon register range.
This is heavily based on the linux mmio-mux driver.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
This will probe the multiplexer devices that have a "u-boot,mux-autoprobe"
property. As a consequence they will be put in their idle state.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Add a new subsystem that handles multiplexer controllers. The API is the
same as in Linux.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
[trini: Update some error calls to use different functions or pass
correct arguments]
Signed-off-by: Tom Rini <trini@konsulko.com>
On a board without hardware clock this software real time clock can be
used. The build time is used to initialize the RTC. So you will have
to adjust the time either manually using the 'date' command or use
the 'sntp' to update the RTC with the time from a network time server.
See CONFIG_CMD_SNTP and CONFIG_BOOTP_NTPSERVER. The RTC time is
advanced according to CPU ticks.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Define default values for input and output clock phase delays for
Versal. Also define functions for setting tapdelays based on these
clock phase delays.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Define and use functions for setting input and output tapdelays
based on clk phase delays.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Define input and output clock phase delays with pre-defined values.
Define arasan_sdhci_clk_data type structure and add it to priv
structure and store these clock phase delays in it.
Read input and output clock phase delays from dt. If these values are
not passed through dt, use pre-defined values.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Just group macros below headers. Other patches will be using this location
too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Define timing macro's for all the available speeds of mmc. This is
done similar to linux. Replace speed macro's used with these new timing
macro's wherever applicable.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This reverts commit 942b5fc032.
This is partial revert of the above commit.
mmc_of_parse() is reading no-1-8-v from device tree and if set,
it is clearing the UHS speed capabilities of cfg->host_caps.
cfg->host_caps &= ~(UHS_CAPS | MMC_MODE_HS200 |
MMC_MODE_HS400 | MMC_MODE_HS400_ES);
This is still missing to clear UHS speeds like SDHCI_SUPPORT_SDR104,
SDHCI_SUPPORT_SDR50 and SDHCI_SUPPORT_DDR50.
Even if we clear the flags SDHCI_SUPPORT_XXX in mmc_of_parse(),
these speed flags are getting set again in cfg->host_caps in
sdhci_setup_cfg().
The reason for this is, SDHCI_SUPPORT_XXX flags are cleared
only if controller is not capable of supporting MMC_VDD_165_195 volts.
if (caps & SDHCI_CAN_VDD_180)
cfg->voltages |= MMC_VDD_165_195;
if (!(cfg->voltages & MMC_VDD_165_195))
caps_1 &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_SDR50 |
SDHCI_SUPPORT_DDR50);
It means "no-1-8-v", which is read from DT is not coming in to effect.
So it is better we keep the host quirks(SDHCI_QUIRK_NO_1_8_V) to
clear UHS speeds based on no-1-8-v from device tree.
Hence revert the functionality related to no-1-8-v only, rest is fine
in the patch.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add function description for zynq_qspi_init_hw and zynq_qspi_chipselect.
Fix zqspi to priv in function descriptions.
Change the description of priv as pointer to zynq_qspi_priv structure.
Fix other function descriptions to kernel-doc style.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use tabs to be aligned with the rest of the code.
Fixes: 658df8bd94 ("mtd: spi-nor-core: Add octal mode support")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to have ZYNQ specific Kconfig macro in generic location
to be visible for all other SoCs. That's why move it to Xilinx common
location to be visible only for us.
Also introduce new bool entry ZYNQ_MAC_IN_EEPROM to have also an option to
disable it or enable. This has connection to code which is reading the
whole content of i2c and also work with the rest of date not just with MAC
address.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove fixed reference clk used by plat->frequency and use clk
subsystem to get reference clk. As per spi dt bindings
"spi-max-frequency" property should be used by the slave devices.
This property is read by spi-uclass driver for the slave device.
So avoid reading above property from the platform driver.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove fixed reference clk used by plat->frequency and use clk
subsystem to get reference clk. As per spi dt bindings
"spi-max-frequency" property should be used by the slave devices.
This property is read by spi-uclass driver for the slave device.
So avoid reading above property from the platform driver.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There also a need to check return values to make sure that clocks were
enabled and setup properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for getting a node/property from aliases.
The similar functionality is provided for chosen node and this
implemenatation is copy of it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove unused variable 'count' which is causing warning while
compilation.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In case of fpga loading (which can be huge) 100ms is not enough. That's why
extend timeout 10 times to wait maximum 1s to get ACK back.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Don't know reason but in regular flow addr_hi/low are swapped in ATF. It
means when fpga load is done from EL3 there is a need to swap it for PMUFW
to load bitstream.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Half of this driver is a DM-based timer driver, and half is RISC-V-specific
IPI code. Move the timer portions in with the other timer drivers. The
KConfig is not moved, since it also enables IPIs. It could also be split
into two configs, but no boards use the timer but not the IPI atm, so I
haven't split it.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Rick Chen <rick@andestech.com>
This matches the naming scheme of other timer drivers.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Rick Chen <rick@andestech.com>
This is a regular timer driver, and should live with the other timer
drivers.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Rick Chen <rick@andestech.com>
free() checks if its argument is NULL. No need to check it twice.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the size of states_array to avoid overflow for
dev_pdata->voltages[j] and dev_pdata->states[j].
As the size of array is GPIO_REGULATOR_MAX_STATES, the size of
states_array is limited by GPIO_REGULATOR_MAX_STATES * 2 = 4
instead of 8 previously.
The value of the "count" variable is limited by the third parameter of
fdtdec_get_int_array_count.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The register to enable/disable the write-permission of DBI RO
registers should be accessed via the CFG_ADDR/CFG_DATA registers
instead of accessing directly.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As per hardware documentation, ECx_PMUX has precedence
over SerDes protocol.
For LX2160/LX2162 if DPMACs 17 and 18 are enabled as SGMII
through SerDes protocol but ECx_PMUX configured them as RGMII,
then the ports will be configured as RGMII and not SGMII.
Signed-off-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Make the MPC8XXX gpio driver to support the fsl-layerscape.
Signed-off-by: hui.song <hui.song_1@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In the current implementation, u-boot creates iommu mappings only
for PCI devices enumarated at boot time thus does not take into
account more dynamic scenarios such as SR-IOV or PCI hot-plug.
Add an u-boot env var and a device tree property (to be used for
example in more static scenarios such as hardwired PCI endpoints
that get initialized later in the system setup) that would allow
two things:
- for a SRIOV capable PCI EP identified by its B.D.F specify
the maximum number of VFs that will ever be created for it
- for hot-plug case, specify the B.D.F with which the device
will show up on the PCI bus
More details can be found in the included documentation:
arch/arm/cpu/armv8/fsl-layerscape/doc/README.pci_iommu_extra
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix duplication of this code by placing it in a common function.
Furthermore, the resulting function will be re-used in upcoming
patches.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move the pci device related fdt fixup in a function in order to
re-use it in a following patch. While at it, improve the error
handling.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
dev_err has been used for debugging and a few dev_err message are
printed for normal code execution. Make them dev_dbg instead.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
By using a hypervisor call, we can implement DEBUG_UART on xen.
This will allow us to see messages even earlier than serial_init().
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
At present, DM_FLAG_PRE_RELOC is set only if !OF_CONTROL.
It doesn't make sense for this para-virtualized driver.
With this patch applied, you will be able to see early boot messages:
U-Boot 2020.10-00001-ge442e71a6c52-dirty (Oct 15 2020 - 11:02:25 +0900)
xenguest
Xen virtual CPU
Model: XENVM-4.15
DRAM: 128 MiB
PVBLOCK:
(XEN) gnttab_mark_dirty not implemented yet
pvblock: 0
In: hypervisor
Out: hypervisor
Err: hypervisor
xenguest#
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
1. Rename AST2500 reset driver from ast2500-reset.c
to reset-ast2500.c
2. Rename AST2500 reset kconfig option from AST2500_RESET
to RESET_AST2500
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
The System Control Unit (SCU) controller of Aspeed
SoCs provides the reset control for each peripheral.
This patch refactors the reset method to leverage
the SCU reset control. Thus the driver dependency
on watchdog including dedicated WDT API and reset
flag encoding can be eliminated.
The Kconfig description is also updated accordingly.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
The 12d152620d commit fixed the get_rate helper because the set_parent
one did not re-parent the clock device to the new parent. The 4d139f3838
commit allows you to remove this workaround by calling the
clk_get_parent_rate routine.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Add support for the hardware pseudo random number generator found in Qualcomm SoC-s.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This adds the driver for the IPQ40xx built-in MDIO.
This will be needed to support future PHY driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds support for the Qualcomm QUP SPI controller that is commonly found in most of Qualcomm SoC-s.
Driver currently supports v1.1.1, v2.1.1 and v2.2.1 HW.
FIFO and Block modes are supported, no support for DMA mode is planned.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
No timer drivers return an error from get_count. Instead of possibly
returning an error, just return the count directly.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The sandbox is built with the SDL2 library with invokes the X11 library
which in turn calls getc(). But getc() in glibc is defined as
int getc(FILE *)
This does not match our definition.
int getc(void)
The sandbox crashes when called with parameter -l.
Rename our library symbol getc() to getchar().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We don't want the debug output to be visible in a normal boot. Silence it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher<hs@denx.de>
This function can be called when it is not known whether it will find
anything. This results in confusing log messages if the device is not
found. It is better for the caller to log the failure, if necessary.
Drop the logging from this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Fix stm32prog command: parsing of FlashLayout without partition
- Update MAINTAINERS for ARM STM STM32MP
- Manage eth1addr on dh board with KS8851
- Limit size of cacheable DDR in pre-reloc stage in stm32mp1
- Use mmc_of_parse() to read host capabilities in mmc:sdmmc2 driver
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl+QXvgACgkQ4rK92eCq
k3Vbrgf/cBKPY9bS+lJVARgjDvIOdcXzpgH/F7dUlq+dzu/mCwhIBVKxM7/nXh5p
RhfGET2fpMYY/41LkKza7AqOiGTXZG4pTmCGe1UHXrXeIPjinWG1LQjU/KOk6U4n
681P9BZfTUXrVgzLBIUY1KBFVyMaiYfVjxU3MnA1vqrubymFbf+IpUt3OIegUDCp
AjrTdj7sFEQ3nG/pgTyqFCwkl/MG53aB9MiaBBRxeGHYnDn0qzAEHSGqzSZZGhNl
1ubJDF3K7w6Pj3MzIeA80M5r0fJoTy/qWcNH31psOpyQaHJ9NbPGjFYE6AkDPV4l
27QN71AcRtCzlv1XQpblA98pa1bUYw==
=Bl3G
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20201021' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Activate CMD_EXPORTENV/CMD_IMPORTENV/CMD_ELF for STM32MP15 defconfig
- Fix stm32prog command: parsing of FlashLayout without partition
- Update MAINTAINERS for ARM STM STM32MP
- Manage eth1addr on dh board with KS8851
- Limit size of cacheable DDR in pre-reloc stage in stm32mp1
- Use mmc_of_parse() to read host capabilities in mmc:sdmmc2 driver
When sending a command via the MDIO bus, the Designware MAC expects some
bits in the CMD register to describe the clock divider value between
the main clock and the MDIO clock.
So far we were omitting these bits, resulting in setting "00", which
means "/ 16", so ending up with an MDIO frequency of either 18.75 or
12.5 MHz.
All the internal PHYs in the H3/H5/H6 SoCs as well as the Gbit Realtek
PHYs seem to be fine with that - although it looks like to be severly
overclocked (the MDIO spec limits the frequency to 2.5 MHz).
However the external 100Mbit PHY on the Pine64 (non-plus) board is
not happy with that, Ethernet was actually never working there, as the
PHY didn't probe.
As we set the EMAC clock (via AHB2) to 300 MHz in ATF (on the 64-bit
SoCs), and use 200 MHz on the H3, we need the highest divider of 128
to let the MDIO clock end up below the required 2.5 MHz.
This enables Ethernet on the Pine64(non-plus).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The current implementation of sun8i_get_ephy_nodes() makes quite some
assumptions, in general relying on DT path names is a bad idea.
I think the idea of the code was to determine if we are using the
internal PHY, for which there are simpler and more robust methods:
Rewrite (and rename) the existing function to simply lookup the DT node
that "phy-handle" points to, using the device's DT node.
Then check whether the parent of that PHY node is using an "H3 internal
MDIO" compatible string. If we ever get another internal MDIO bus
implementation, we will probably need code adjustments anyway, so this
is good enough for now.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[jagan: rebase on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The error handling in recv() is somewhat broken, for instance
good_packet isn't really used, and it's hardly readable. Also we try
to check for short or too big packets, but those are actually filtered
out by the hardware.
Simplify the whole routine and improve the error handling:
- Bail out early if the current RX descriptor is not ready.
- Enable propagation of runt, huge and broken packets.
- Check for runt and huge packets, and return 0 to indicate this.
This will force the framework to call free_pkt for cleanup.
- Avoid aligning the packet buffer for invalidation again.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The EMAC soft reset routine was subtly broken, using an open coded
timeout routine without any actual delay.
Remove the unneeded initial reset bit read, and call wait_for_bit_le32()
to handle the timeout correctly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When iterating over all RX/TX buffers, we were using a rather long "idx"
control variable, which lead to a nasty overlong line.
Replace "idx" with "i" to avoid this.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
To meet the current alignment requirements for our cache maintenance
functions, we were explicitly aligning the *arguments* to those calls.
This is not only ugly to read, but also wrong, as we need to make sure
we are not accidentally stepping on other data.
Provide wrapper functions for the common case of cleaning or
invalidating a descriptor, to make the cache maintenance calls more
readable. This fixes a good deal of the problematic calls.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
There is no reason to invalidate a TX descriptor before we are setting
it up, as we will only write to a field.
Remove the not needed invalidate_dcache_range() call.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When we initialise the TX descriptors, there is no need yet to clean
them all to memory, as they don't contain any data yet. Later we will
touch and clean each descriptor anyway.
However we tell the MAC about the beginning of the chain, so we have to
clean at least the first descriptor, to make it clear that this is empty
and there are no packets to transfer yet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Before we initialise the RX descriptors, there is no need to *clean*
them from the cache, as we touch them for the first time.
However we should cover the case that those buffers contain dirty cache
lines, which could be evicted and written back to DRAM any time later,
in the worst case *after* the MAC has transferred a packet into them.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The EMAC driver contains a lot of magic bits, although the manuals
and the Linux driver have all names for them.
Define those names and use them when programming the registers.
Also this replaces a lot of readl/mask/writel operations with the much
easier-to-read setbits_le32() macro.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Apparently due to copying from some older or converted driver, the
sun8i_emac driver contains pointless wrapper functions to bridge
between a legacy driver and the driver model.
Since sun8i_emac is (and always was) driver model only, there is no
reason to have those confusing wrappers. Just remove them, and use
the driver model prototypes directly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When preparing the register value for the MDIO command register, we
start with a zeroed register, so there is no need to mask off certain
bits before setting them.
Simplify the sequence, and rename the variable to a more matching
mii_cmd on the way.
Also the open-coded time-out routine can be replaced with a much safer
and easier-to-read call to wait_for_bit_le32().
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When initialising the TX DMA descriptors, we mostly chain them up,
but of course don't know about any data or its length yet.
That means they are still invalid, and the OWN bit should NOT be set
yet.
In fact when we later tell the MAC about the beginning of the chain,
and enable TX DMA in the start() routine, the MAC will start fetching
TX descriptors prematurely, as it can be seen by dumping the TX_DMA_STA
and TX_DMA_CUR_DESC registers.
Clear the owner bit, to not give the MAC the wrong illusion that it
owns the descriptors already.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When phy_startup() returns with an error, because there is no link or
the user interrupted the process, we shall stop the _start() routine
and return with an error, instead of proceeding anyway.
This fixes pointless operations when there is no Ethernet cable
connected, for instance.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cosmetic update of gpio.h:
- remove enumerate: stm32_gpio_port, stm32_gpio_pin
because STM32_GPIO_XXX values are unused
- move STM32_GPIOS_PER_BANK in stm32_gpio.c
as its value is IP dependent and not arch dependent
No functional change as number of banks and number of gpio by banks
is managed by device tree since since DM migration and
commit 8f651ca60b ("pinctrl: stm32: Add get_pins_count() ops").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
mmc_of_parse() can populate the 'f_max' and 'host_caps' fields of
struct mmc_config from devicetree.
The same logic is duplicated in stm32_sdmmc2_probe(). Use
mmc_of_parse(), which is more generic.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
"cap-mmc-highspeed" enables support for 26 MHz MMC, but there is no
additional flag to enable 52 MHz MMC. In Linux. "cap-mmc-highspeed"
is used for MMC HS at both 26MHz and 52MHz.
Use the same approach and enable MMC_CAP(MMC_HS_52) host capability
when "cap-mmc-highspeed" is found in the devicetree. In the event an
MMC card doesn't support 52 MHz, it will be clocked at a speed based
on its EXT CSD, even on 52 MHz host controllers
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Sync the R8A77990 SoC PFC tables with Linux 5.9 , commit bbf5c979011a.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
This sync's the RZ/G2H clock tables with mainline linux 5.9 commit
bbf5c979011a ("Linux 5.9").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
This sync's the RZ/G2N clock tables with mainline linux 5.9 commit
bbf5c979011a ("Linux 5.9").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Add fallback compatibility string for R-Car Gen3 and RZ/G2.
Also sorted the compatible string as per SoC ID.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Add an entry in usb_gadget_controller_number() for the MTU3
gadget controller. It is used to bind the USB Ethernet driver.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds support for the MediaTek USB3 DRD controller,
its host side is based on xHCI, this driver supports device mode
and host mode.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
There is only declaration of usb_speed_string(), but no definition,
so add it to avoid build error when call it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In buffer DMA mode, gadget should re-configure EP 0 to received SETUP
packets when doeptsiz.xfersize is equal to a setup packet size(8 bytes)
and EP 0 is in WAIT_FOR_SETUP state.
Since EP 0 is not enabled in WAIT_FOR_SETUP state, SETUP packets is NOT
received from RxFifo and wriiten to the external memory.
Signed-off-by: Chance.Yang <chance.yang@vatics.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl+NMmQcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyLnEB/0cWFfjDfCMY1o7R4QX
DeDRlD6k6acQWlwa5EiRKwpbPMJKrSI/m5alMCYZG6YHvGtzihqnqohz3gl1sepi
W7eyyyFsM4hqe4P3lSETJRGWe/O8bNkoa0hBzqZ9btqw2OJLBu4JYB+zKgz8kaDY
jzkGLgaaK6wtG3rEu+q4fjzp1y9kuz31WnN+9qS8jd/9UH13XKCkJl9TfY5pLfgc
mmbn2NWtAhi91uShcnIsOpLaNm23IV0ITa22etB9F1docZuUrbhOtiIF45AADjpG
/xtkV3dEVGml3N/17RizgOwxX3xughG0ak9xifsK6tfgqfVhaGMgkToNNBM+1ddm
rZZM
=hF12
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.01 cycle:
This feature set brings the rework of the clock tree for sam9x60 SoC.
This makes the clock tree fully compatible with Common Clock Framework
and allows full clock configuration in U-Boot. This means that the
sam9x60 boards can boot now using U-Boot.
This also includes the definitions for sam9x60 SiPs and a divisor fix
for the clock on sama7g5 SoC.
This SoC has the 5th divisor for the mck0 master clock.
Adapt the characteristics accordingly.
Reported-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
clk-master can have 5 divisors with a field width of 3 bits
on some products.
Change the mask and number of divisors accordingly.
Reported-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Done with:
./tools/moveconfig.py VIDEO_BMP_GZIP
The 3 suspicious migration because CMD_BMP and SPLASH_SCREEN
are not activated in these defconfigs:
- trats_defconfig
- s5pc210_universal_defconfig
- trats2_defconfig
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For levels equal to the maximum value, the duty cycle must be equal to
the period.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Amlogic D-PHY in the Amlogic AXG SoC Family does support a frequency
higher than 10MHz for the TX Escape Clock, thus make the target rate
configurable.
This is based on the Linux commit [1] and adapted to the U-Boot driver.
[1] a328ca7e4af3 ("drm/bridge: dw-mipi-dsi: permit configuring the escape clock rate")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The timing values for dw-dsi are often dependent on the used display and
according to Philippe Cornu will most likely also depend on the used phy
technology in the soc-specific implementation.
To solve this and allow specific implementations to define them as needed
add a new get_timing callback to phy_ops and call this from the dphy_timing
function to retrieve the necessary values for the specific mode.
This is based on the Linux commit [1] and adapted to the U-Boot driver.
[1] 25ed8aeb9c39 ("drm/bridge/synopsys: dsi: driver-specific configuration of phy timings")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This driver doesn't use DM (in the correct places), so we use a device and
not a udevice. We also need to include device_compat.h
Signed-off-by: Sean Anderson <seanga2@gmail.com>
This patch enhances the Octeon TX/TX2 watchdog driver to fully enable
the WDT. With this changes, the "wdt" command is now also supported
on these platforms.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Suneel Garapati <sgarapati@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Remove a left-over debug test message from the Octeon TX / TX2
MMC driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Suneel Garapati <sgarapati@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Octeon TX2 sets the TB100_EN bit in the config register. We need to use
a fixed 100MHz clock for this as well to work properly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Suneel Garapati <sgarapati@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
- fsl_esdhc_imx cleanup
- not send cm13 if send_status is 0.
- Add reinit API
- Add mmc HS400 for fsl_esdhc
- Several cleanup for fsl_esdhc
- Add ADMA2 for sdhci
- Octeon TX: Add NAND driver (Suneel)
- Octeon TX: Add NIC driver driver (Suneel)
- Octeon TX2: Add NIC driver driver (Suneel)
- Armada 8040: Add iEi Puzzle-M80 board support (Luka)
- Armada A37xx SPI: Add support for CS-GPIO (George)
- Espressobin: Use Linux model/compatible strings (Andre)
- Espressobin: Add armada-3720-espressobin-emmc.dts from Linux (Andre)
- Armada A37xx: Small cleanup of config header (Pali)
Set the defaults on probe for the packet buffer size registers
for the i210.
The TX/RX PBSIZE register of the i210 resets to its default value
only at power-on - see Intel Ethernet Controller I210 Datasheet rev 3.5
chapter 8.3 'Internal Packet Buffer Size Registers'.
If something (another driver, another OS, etc.) modifies this register
from its default value, the e1000 driver doesn't function correctly. It
detects a hang of the transmitter and continuously resets the adapter.
Here we set this value to its default when resetting the i210 to
resolve this issue.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
CONFIG_IS_ENABLED() takes the kconfig name without the CONFIG_ prefix,
e.g. CONFIG_IS_ENABLED(CLK) for CONFIG_CLK. Some of these were being
fixed every now and then, see:
commit 71ba2cb0d6 ("board: stm32mp1: correct CONFIG_IS_ENABLED usage for LED")
commit a5ada25e42 ("rockchip: clk: fix wrong CONFIG_IS_ENABLED handling")
commit 5daf6e56d3 ("common: console: Fix duplicated CONFIG in silent env callback")
commit 48bfc31b64 ("MIPS: bootm: Fix broken boot_env_legacy codepath")
Fix all files found by `git grep "CONFIG_IS_ENABLED(CONFIG"` by running
':%s/CONFIG_IS_ENABLED(CONFIG_\(\w+\))/CONFIG_IS_ENABLED(\1)/g' in vim.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since it's so trivial I could just about tolerate this when there were only
two copies of it. But now there are about to be three.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
For testing purposes keep the output value when switching to input.
This allows us to manipulate the input value via the gpio command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Newer eSDHC controllers support ADMA2 descriptor tables which support
64bit DMA addresses. One notable user of addresses in the upper memory
segment is the EFI loader.
If support is enabled, but the controller doesn't support ADMA2, we
will fall back to SDMA (and thus 32 bit DMA addresses only).
Signed-off-by: Michael Walle <michael@walle.cc>
The device tree has a way to specify GPIO lines as chip selects. From
the binding docs:
So if for example the controller has 2 CS lines, and the cs-gpios
property looks like this:
cs-gpios = <&gpio1 0 0> <0> <&gpio1 1 0> <&gpio1 2 0>;
Then it should be configured so that num_chipselect = 4 with the
following mapping:
cs0 : &gpio1 0 0
cs1 : native
cs2 : &gpio1 1 0
cs3 : &gpio1 2 0
Add support for this, while retaining backward-compatibility with
existing device trees; the driver will preserve existing behavior if a
cs-gpios list is not given, or if a particular line is specified as <0>
(native).
This implementation is inspired by similar implementations in
neighboring drivers for other platforms: atmega, mxc, etc.
Signed-off-by: George Hilliard <ghilliar@amazon.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Adds support for Network Interface controllers found on
OcteonTX2 SoC platforms.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Adds support for Network Interface controllers found on
OcteonTX SoC platforms.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Adds support for NAND controllers found on OcteonTX or
OcteonTX2 SoC platforms. Also includes driver to support
Hardware ECC using BCH HW engine found on these platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
- Minor cleanup on K3 env variables
- Fix OSPI compatible for J721e
- Drop unused property in omap-usb2-phy
- Update Maintainer for am335x-guardian board.
Currently, readl/writel and esdhc_read32/esdhc_write32 are used. To align
the usage, change to only use esdhc_read32/esdhc_write32.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
There are other (non-SDHCI) controllers which supports ADMA2 descriptor
tables, namely the Freescale eSDHC. Instead of copying the code, move it
into an own module.
Signed-off-by: Michael Walle <michael@walle.cc>
First, we need the waterlevel setting for PIO mode only. Secondy, both DMA
setup code is identical for both directions, except for the data pointer.
Thus, unify them.
Signed-off-by: Michael Walle <michael@walle.cc>
Use the dma_{map,unmap}_single() calls. These will take care of the
flushing and invalidation of caches.
Signed-off-by: Michael Walle <michael@walle.cc>
SDMA can only do DMA with 32 bit addresses. This is true for all
architectures (just doesn't apply to 32 bit ones). Simplify the code and
remove unnecessary CONFIG_FSL_LAYERSCAPE.
Also make the error message more concise.
Signed-off-by: Michael Walle <michael@walle.cc>
This 1ms delay before sending command already exist from the beginning
of the fsl_esdhc driver added in year 2008. Now this driver has been
split for two files: fsl_esdhc.c and fsl_esdhc_imx.c. fsl_esdhc_imx.c
only for i.MX series. i.MX series esdhc/usdhc do not need this 1ms delay
before sending any command. So remove this 1ms, this will save a lot
time if handling a large mmc data.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
According to the code logic in __mmc_switch, if the parameter 'send_status'
is zero, no need to send cmd13, just wait the stated timeout time, then
can return directly.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
There was a fix-up for eMMC HS400 stability issue in Linux.
Patch link:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/
commit/?id=58d0bf843b49fa99588ac9f85178bd8dfd651b53
Description:
Currently only LX2160A eSDHC supports eMMC HS400. According to
a large number of tests, eMMC HS400 failed to work at 150MHz,
and for a few boards failed to work at 175MHz. But eMMC HS400
worked fine on 200MHz. We hadn't found the root cause but
setting eSDHC_DLLCFG0[DLL_FREQ_SEL] = 0 using slow delay chain
seemed to resovle this issue. Let's use this as fixup for now.
Introduce the fix-up in u-boot since the issue could be reproduced
in u-boot too.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Fix mmc->clock with actual clock which is divided by the
controller, and record it with priv->clock which was removed
accidentally.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The process for eMMC HS400 mode for eSDHC is,
1. Perform the Tuning Process at the HS400 target operating frequency.
Latched the clock division value.
2. if read transaction, then set the SDTIMNGCTL[FLW_CTL_BG].
3. Switch to High Speed mode and then set the card clock frequency to
a value not greater than 52Mhz
4. Clear TBCTL[TB_EN],tuning block enable bit.
5. Change to 8 bit DDR Mode
6. Switch the card to HS400 mode.
7. Set TBCTL[TB_EN], tuning block enable bit.
8. Clear SYSCTL[SDCLKEN]
9. Wait for PRSSTAT[SDSTB] to be set
10. Change the clock division to latched value.Set TBCTL[HS 400 mode]
and Set SDCLKCTL[CMD_CLK_CTRL]
11. Set SYSCTL[SDCLKEN]
12. Wait for PRSSTAT[SDSTB] to be set
13. Set DLLCFG0[DLL_ENABLE] and DLLCFG0[DLL_FREQ_SEL].
14. Wait for delay chain to lock.
15. Set TBCTL[HS400_WNDW_ADJUST]
16. Again clear SYSCTL[SDCLKEN]
17. Wait for PRSSTAT[SDSTB] to be set
18. Set ESDHCCTL[FAF]
19. Wait for ESDHCCTL[FAF] to be cleared
20. Set SYSCTL[SDCLKEN]
21. Wait for PRSSTAT[SDSTB] to be set.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Add a mmc_hs400_prepare_ddr() interface for controllers
which needs preparation before switching to DDR mode for
HS400 mode.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Some controllers may have difference between HS200 tuning
and HS400 tuning, such as different registers setting,
different procedure, or different errata.
This patch is to add a hs400_tuning flag to identify the
tuning for HS400 mode.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
For DM_MMC, the controller re-initialization is needed to
clear old configuration for mmc rescan.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
"ti,dis-chg-det-quirk" property is not part of Linux kernel DT binding
documentation. Therefore drop this and instead use soc_device_match()
to distinguish b/w AM654 SR1.0 and SR2.0 devices similar to Linux kernel
driver.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reset the channel completely during channel release in order to clear
teardown bit before handing over to next user or jumping to Linux.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Enable FPGA full reconfiguration support with Intel FPGA SDM
Mailbox driver for Agilex.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Ensure watchdog reset is not triggered if the fpga
reconfiguration is taking too long.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Rename Stratix10 FPGA driver to Intel FPGA SDM Mailbox driver
because it is using generic SDM (Secure Device Manager) Mailbox
interface shared by other platform (e.g. Agilex) as well.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Rename the driver from S10 to SoC64 because Intel Agilex platform
also using the this SYSRESET SoCFPGA driver for S10.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add additional membus writes to configure main and peripheral PLL
for Agilex's clock manager.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Since warm reset may optionally set the CLock Manager to'boot mode',
the clock driver should always force the Agilex's Clock Manager to
'boot mode' before the clock driver start configuring the Clock Manager
in SPL.
In SSBL, clock driver will skip the Clock Manager configuration
if it's already being setup by SPL (Clock Manager NOT in 'boot
mode') to prevent any inaccurate clocking issues happened on HPS
peripherals such as UART, MAC and etc.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Some drivers probing failed if clock enable function is not supported in
clock driver. So, add clock enable function to clock driver to solve it.
Return 0 (success) for *.enable function because all clocks are enabled
by default in clock driver probe.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
The timeout calculation is based on the clk being in KHz but
the clk api returns the clk value in Hz. Convert this to KHz
to calculate the correct timeout value.
Signed-off-by: Jack Mitchell <ml@embed.me.uk>
This more closely mirrors Linux's behaviour, and will make it easier to
transition to using function+color in the future.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
dm_gpio_ops.get_value can be called when the gpio is either input or
output. The current dw code always returns the input value, which is
invalid if the direction is set to out.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Previously, if there was no bank-name property, it was easy to have
confusing gpio names like "gpio1@08", instead of "gpio1@0_8". This patch
follows the example of the sifive gpio driver.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Change the type of gpio_dwabp_platdata.base from fdt_addr_t to a void
pointer, since we pass it to readl.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Fully-Programmable Input/Output Array (FPIOA) device controls pin
multiplexing on the K210. The FPIOA can remap any supported function to any
multifunctional IO pin. It can also perform basic GPIO functions, such as
reading the current value of a pin. However, GPIO functionality remains
largely unimplemented (in favor of the dedicated GPIO peripherals).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This extends the pinctrl-sandbox driver to support pin muxing, and adds a
test for that behaviour. The test is done in C and not python (like the
existing tests for the pinctrl uclass) because it needs to call
pinctrl_select_state. Another option could be to add a command that
invokes pinctrl_select_state and then test everything in
test/py/tests/test_pinmux.py.
The pinctrl-sandbox driver now mimics the way that many pinmux devices
work. There are two groups of pins which are muxed together, as well as
four pins which are muxed individually. I have tried to test all normal
paths. However, very few error cases are explicitly checked for.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The pinmux property allows for smaller and more compact device trees,
especially when there are many pins which need to be assigned individually.
Instead of specifying an array of strings to be parsed as pins and a
function property, the pinmux property contains an array of integers
representing pinmux groups. A pinmux group consists of the pin identifier
and mux settings represented as a single integer or an array of integers.
Each individual pin controller driver specifies the exact format of a
pinmux group. As specified in the Linux documentation, a pinmux group may
be multiple integers long. However, no existing drivers use multi-integer
pinmux groups, so I have chosen to omit this feature. This makes the
implementation easier, since there is no need to allocate a buffer to do
endian conversions.
Support for the pinmux property is done differently than in Linux. As far
as I can tell, inversion of control is used when implementing support for
the pins and groups properties to avoid allocating. This results in some
duplication of effort; every property in a config node is parsed once for
each pin in that node. This is not such an overhead with pins and groups
properties, since having multiple pins in one config node does not occur
especially often. However, the semantics of the pinmux property make such a
configuration much more appealing. A future patch could parse all config
properties at once and store them in an array. This would make it easier to
create drivers which do not function solely as callbacks from
pinctrl-generic.
This commit increases the size of the sandbox build by approximately 48
bytes. However, it also decreases the size of the K210 device tree by 2
KiB from the previous version of this series.
The documentation has been updated from the last Linux commit before it was
split off into yaml files.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
the aspeed ddr sdram controller needs to know if the memory chip mounted on
the board is dual x8 die or not. Or it may get the wrong size of the
memory space.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
to improve the maintainability. It is more easier to modify and add
configurations of the driver in the centralized ram driver directory.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
The cfi-flash driver uses an open-coded version of the generic
algorithm to decode and translate multiple frames of a "reg" property.
This starts off the wrong foot by using the address-cells and size-cells
properties of *this* very node, and not of the parent. This somewhat
happened to work back when we were using a wrong default size of 2,
but broke about a year ago with commit 0ba41ce1b7 ("libfdt: return
correct value if #size-cells property is not present").
Instead of fixing the reinvented wheel, just use the generic function
that does all of this properly.
This fixes U-Boot on QEMU (-arm64), which was crashing due to decoding
a wrong flash base address:
DRAM: 1 GiB
Flash: "Synchronous Abort" handler, esr 0x96000044
elr: 00000000000211dc lr : 00000000000211b0 (reloc)
elr: 000000007ff5e1dc lr : 000000007ff5e1b0
x0 : 00000000000000f0 x1 : 000000007ff5e1d8
x2 : 000000007edfbc48 x3 : 0000000000000000
x4 : 0000000000000000 x5 : 00000000000000f0
x6 : 000000007edfbc2c x7 : 0000000000000000
x8 : 000000007ffd8d70 x9 : 000000000000000c
x10: 0400000000000003 x11: 0000000000000055
^^^^^^^^^^^^^^^^
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stefan Roese <sr@denx.de>
When possible use DMA for reading from CFI flash, this provides upto 5x
improvement in read performance with high speed CFI compliant flashes
like HyperFlash.
Code will gracefully fallback to CPU copy when DMA is unavailable.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Caller would need gracefully handle failures of dma_get_device(),
therefore reduce pr_err() to pr_debug() when DMA device is not found.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- mips: octeon: add support for DWC3 USB
- mips: octeon: add support for booting Linux
-----BEGIN PGP SIGNATURE-----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=v+p3
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-10-07' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips
- mips: octeon: add support for DDR4 memory controller
- mips: octeon: add support for DWC3 USB
- mips: octeon: add support for booting Linux
This patch adds the glue layer for the MIPS Octeon SoCs. It's ported
mainly from the Linux code.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Octeon uses mapped addresses for virtual and physical memory. It's not
that easy to calculate the resulting addresses here. So let's remove
this BUG_ON() completely, as it's not really helpful.
Please also note, that BUG_ON() is not recommended any more in the Linux
kernel.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
On MIPS platforms, mapping of the base address is needed. This patch
switches from dev_get_addr() to dev_remap_addr() to get the mapped base
address of the xHCI controller.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
This Octeon 3 DDR driver is ported from the 2013 Cavium / Marvell U-Boot
repository. It currently supports DDR4 on Octeon 3. It can be later
extended to support also DDR3 and Octeon 2 platforms.
Part 3 includes the DIMM SPD handling code and the Kconfig / Makefile
integration.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This Octeon 3 DDR driver is ported from the 2013 Cavium / Marvell U-Boot
repository. It currently supports DDR4 on Octeon 3. It can be later
extended to support also DDR3 and Octeon 2 platforms.
Part 2 includes the very complex Octeon 3 DDR4 configuration
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This Octeon 3 DDR driver is ported from the 2013 Cavium / Marvell U-Boot
repository. It currently supports DDR4 on Octeon 3. It can be later
extended to support also DDR3 and Octeon 2 platforms.
Part 1 adds the base U-Boot RAM driver, which will be instantiated by
the DT based probing.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The cell_count argument is required when cells_name is NULL.
This patch adds this parameter in live tree API
- of_count_phandle_with_args
- ofnode_count_phandle_with_args
- dev_count_phandle_with_args
This parameter solves issue when these API is used to count
the number of element of a cell without cell name. This parameter
allow to force the size cell.
For example:
count = dev_count_phandle_with_args(dev, "array", NULL, 3);
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
-----BEGIN PGP SIGNATURE-----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=rbAX
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20201005' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- generate unique mac address from SoC serial on S400 board
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
This adds the driver for the PWM controller found in the Amlogic SoCs.
This PWM is only a set of Gates, Dividers and Counters:
PWM output is achieved by calculating a clock that permits calculating
two periods (low and high). The counter then has to be set to switch after
N cycles for the first half period.
The hardware has no "polarity" setting. This driver reverses the period
cycles (the low length is inverted with the high length) for
PWM_POLARITY_INVERSED.
Disabling the PWM stops the output immediately (without waiting for the
current period to complete first).
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The AXG pmx driver gpio request offset needs the pin base to have the
correct pin number.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The registers which are managed by the meson-gxl-usb3 PHY driver are
actually "USB control" registers (which are "glue" registers which
manage OTG detection and routing of the OTG capable port between the
DWC2 peripheral-only controller and the DWC3 host-only controller).
Drop the meson-gxl-usb3 PHY driver now that the dwc3-meson-gxl-usb
driver supports the USB control registers on GXL and GXM SoCs (these
were previously managed by the meson-gxl-usb3 PHY driver).
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The USB support was initialy done with a set of PHYs and dwc3-of-simple
because the architecture of the USB complex was not understood correctly
at the time (and proper documentation was missing...).
But with the G12A family, the USB complex was correctly understood and
implemented correctly.
This adds a proper driver for the glue, based on the G12A one, but with
enough changes to require a different driver in U-Boot.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl960JkcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDaWCACYjvloDzXQaYaauWwR
whFwgkUAQ8yjadj/12We/X2b7HGisNFNE80e/V4MU8RrJDFZmohZdLWMfRKez29X
d+BG+OzVXxHWozny7ZQ2g1yYJbgCI7sVUeemQjUBZJ6aKPneQlVfwyfT2l88wOVK
yQMqS+ZyVogihR9/NHCOlJHog+6OOoBmc16w1tymM6QcO8ZsYeA66ed8SLnjDb3N
Rg2Ll2RR/lHuD/Fpxt1aUhybXFKSIOr4Qopo5X0hw5B3ibkp6JXGRE2wIwQYw6CA
q+sKTg37CSzylipkQ5EOGdLcXD7r3KIGkSbUMb8wvt6dROarnIuQ+zJeF3sr+l2H
hSoU
=vHqZ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for 2021.01 cycle:
This feature set includes a new CPU driver for at91 family, new driver
for PIT64B hardware timer, support for new at91 family SoC named sama7g5
which adds: clock support, including conversion of the clock tree to
CCF; SoC support in mach-at91, pinctrl and mmc drivers update. The
feature set also includes updates for mmc driver and some other minor
fixes and features regarding building without the old Atmel PIT and the
possibility to read a secondary MAC address from a second i2c EEPROM.
- stm32mp: convert drivers to APIs which support live DT
- stm32mp: gpio: minor fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl93OLYACgkQ4rK92eCq
k3VQ3ggAlv+e3IXylevdLrCGtoPNb0mC3pB7fKcXedZ7YOHi+ag6MfLKFb3K8UCV
1h8iUX3XpGxOuOzOlqu89UFZBZXkbKP3bPnOJD8AliTEcZN/rTdZK43qYbAVM3tL
UvOtCXMzujmGwJsJqLQmXKK761fpcJFzEisajX+d6cz+at3oMF2Yoa/1RcC8Z7fi
DHWaUME132H5A9pzmt84N83neJNgMmFIDyHBWjNSMkvdiE5jz8MAPFrua8FDyymS
w0QmKmN0ub+5kJqXu4X/LCMZUjYozC3lfNbnwRIkXXKJtQuGEea963bBi7Gastdb
gSCQKmrwjtxa4/g/bpalDTMAvirKnQ==
=Q/62
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20201003' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm into next
- stm32mp: DT alignment with Linux 5.9-rc4
- stm32mp: convert drivers to APIs which support live DT
- stm32mp: gpio: minor fixes
Currently, the return value of dev_read_u32_default is stored in an u32,
causing the subsequent "if (function < 0)" to always be false:
u32 function;
...
function = dev_read_u32_default(config, "brcm,function", -1);
if (function < 0) {
debug("Failed reading function for pinconfig %s (%d)\n",
config->name, function);
return -EINVAL;
}
Make "function" variable an int to fix this.
Cc: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Factor out reading IP base address to ofdata_to_platdata function, which
is designed for this purpose. Also, drop the dev->priv NULL check, since
this is already done by the dm core when allocating space using
priv_auto_alloc_size feature. (in drivers/core/device.c ->
device_ofdata_to_platdata).
Cc: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Yannick Fertré <yannick.fertre@st.com>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Yannick Fertré <yannick.fertre@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add test on the size of ofnode_phandle_args result to avoid access
to uninitialized elements in args[] field.
This patch avoids the issue when gpio-ranges cell size is not 3 as
expected, for example:
gpio-ranges = <&pinctrl 0>;
instead of
gpio-ranges = <&pinctrl 0 112 16>;
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move the variables definition at the beggining of the function
gpio_stm32_probe().
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Upon further discussion on the mailing list, we should not get in the
situation where the generic code path to set ethaddr/etc correctly does
not work. Revert this until someone can further debug the smc911x
driver regarding this issue.
This reverts commit 387cbf096e.
Signed-off-by: Tom Rini <trini@konsulko.com>
The R8A774A1 is compatible with the generic rcar-gen3-xhci controller.
This patch adds the compatibility flag, to support the xHCI controller.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Use readx_poll_sleep_timeout() to poll the register status
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use macros with parameter to fill ep_info2, then some macros
for MASK and SHIFT can be removed
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use TRB_TX_TYPE() instead of (TRB_DATA_OUT/IN << TRB_TX_TYPE_SHIFT)
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For normal TRB fields:
use TRB_LEN(x) instead of ((x) & TRB_LEN_MASK);
and use TRB_INTR_TARGET(x) instead of
(((x) & TRB_INTR_TARGET_MASK) << TRB_INTR_TARGET_SHIFT)
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There some vendor quirks for MTK xHCI 0.96 host controller:
1. It defines some extra SW scheduling parameters for HW
to minimize the scheduling effort for synchronous and
interrupt endpoints. The parameters are put into reserved
DWs of slot context and endpoint context.
2. Its TDS in Normal TRB defines a number of packets that
remains to be transferred for a TD after processing all
Max packets in all previous TRBs.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
xhci versions 1.0 and later report the untransferred data remaining in a
TD a bit differently than older hosts.
We used to have separate functions for these, and needed to check host
version before calling the right function.
Now Mediatek host has an additional quirk on how it uses the TD Size
field for remaining data. To prevent yet another function for calculating
remainder we instead want to make one quirk friendly unified function.
Porting from the Linux:
c840d6ce772d("xhci: create one unified function to calculate TRB TD remainder.")
124c39371114("xhci: use boolean to indicate last trb in td remainder calculation")
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a member to save xHCI version, it's used some times.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
commit 7c8f821e5d ("i2c: rcar_i2c: Set the slave address from
rcar_i2c_xfer") blindly called rcar_i2c_set_addr() with read argument
always set to 1 during xfer which introduced read/write errors, whereas
earlier rcar_i2c_read_common() called rcar_i2c_set_addr() with read set to
1 and rcar_i2c_write_common() called rcar_i2c_set_addr() with read set 0.
Fixes: 7c8f821e5d ("i2c: rcar_i2c: Set the slave address from rcar_i2c_xfer")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support for stingray PAXB PHY controller driver.
This driver supports maximum 8 PAXB phys using pipemux data.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The ethernet controller can read the MAC from EEPROM and display it,
but if ethaddr is not set, the ethernet is still unavailable.
This patch checks will automatically set the MAC address if it has
not already been set.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
ftgmac100 driver is using hard-coded PHY interface address of zero.
Each board can have different PHY interface address (phy_addr).
This commit modifies the driver to make use of board specific address
by leveraging CONFIG_PHY_ADDR.
Signed-off-by: Thirupathaiah Annapureddy <thiruan@linux.microsoft.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The Linux kernel does set the clock delays to
- 0.2 ns (their default, and lowest, hardware value) if delays should
not be enabled
- 2.0 ns (which causes the data to be sampled at exactly half way between
clock transitions at 1000 Mbps) if delays should be enabled
depending on the interface mode
See https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/phy/mscc/mscc_main.c#n523
So instead of using arbitrary delay values like now, mimic this behaviour.
The behaviour is the same for all of vsc8530/8531/8540/8541 so move that
to a shared function while at it.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The vsc8530/8531/8540/8541 phys have a configurable clock output that
can emit 25, 50 and 125 MHz rates, which in turn may be needed for
stable network connections.
This follows a similar change introduced into the Linux kernel at
https://lore.kernel.org/netdev/20200609133140.1421109-2-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add tests for SCMI reset controllers. A test device driver
sandbox-scmi_devices.c is used to get reset resources, allowing further
resets manipulation.
Change sandbox-smci_agent to emulate 1 reset controller exposed through
an agent. Add DM test scmi_resets to test this reset controller.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change introduces a reset controller driver for SCMI agent devices.
When SCMI agent and SCMI reset domain drivers are enabled, SCMI agent
binds a reset controller device for each SCMI reset domain protocol
devices enabled in the FDT.
SCMI reset driver is embedded upon CONFIG_RESET_SCMI=y. If enabled,
CONFIG_SCMI_AGENT is also enabled.
SCMI Reset Domain protocol is defined in the SCMI specification [1].
Links: [1] https://developer.arm.com/architectures/system-architectures/software-standards/scmi
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add tests for SCMI clocks. A test device driver sandbox-scmi_devices.c
is used to get clock resources, allowing further clock manipulation.
Change sandbox-smci_agent to emulate 3 clocks exposed through 2 agents.
Add DM test scmi_clocks to test these 3 clocks.
Update DM test sandbox_scmi_agent with load/remove test sequences
factorized by {load|remove}_sandbox_scmi_test_devices() helper functions.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change introduces a clock driver for SCMI agent devices. When
SCMI agent and SCMI clock drivers are enabled, SCMI agent binds a
clock device for each SCMI clock protocol devices enabled in the FDT.
SCMI clock driver is embedded upon CONFIG_CLK_SCMI=y. If enabled,
CONFIG_SCMI_AGENT is also enabled.
SCMI Clock protocol is defined in the SCMI specification [1].
Links: [1] https://developer.arm.com/architectures/system-architectures/software-standards/scmi
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change implements a SMCCC transport for SCMI exchanges. This
implementation follows the Linux kernel as references implementation
for SCMI message processing, using the SMT format for communication
channel meta-data.
Use of SMCCC transport in SCMI FDT bindings are defined in the Linux
kernel DT bindings since v5.8. SMCCC with SMT is implemented in OP-TEE
from tag 3.9.0 [2].
Links: [2] https://github.com/OP-TEE/optee_os/commit/a58c4d706d23
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change implements a mailbox transport using SMT format for SCMI
exchanges. This implementation follows the Linux kernel and
SCP-firmware [1] as references implementation for SCMI message
processing using SMT format for communication channel meta-data.
Use of mailboxes in SCMI FDT bindings are defined in the Linux kernel
DT bindings since v4.17.
Links: [1] https://github.com/ARM-software/SCP-firmware
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change introduces SCMI agent uclass to interact with a firmware
using the SCMI protocols [1].
SCMI agent uclass currently supports a single method to request
processing of the SCMI message by an identified server. A SCMI message
is made of a byte payload associated to a protocol ID and a message ID,
all defined by the SCMI specification [1]. On return from process_msg()
method, the caller gets the service response.
SCMI agent uclass defines a post bind generic sequence for all devices.
The sequence binds all the SCMI protocols listed in the FDT for that
SCMI agent device. Currently none, but later change will introduce
protocols.
This change implements a simple sandbox device for the SCMI agent uclass.
The sandbox nicely answers SCMI_NOT_SUPPORTED to SCMI messages.
To prepare for further test support, the sandbox exposes a architecture
function for test application to read the sandbox emulated devices state.
Currently supports 2 SCMI agents, identified by an ID in the FDT device
name. The simplistic DM test does nothing yet.
SCMI agent uclass is designed for platforms that embed a SCMI server in
a firmware hosted somewhere, for example in a companion co-processor or
in the secure world of the executing processor. SCMI protocols allow an
SCMI agent to discover and access external resources as clock, reset
controllers and more. SCMI agent and server communicate following the
SCMI specification [1]. This SCMI agent implementation complies with
the DT bindings defined in the Linux kernel source tree regarding
SCMI agent description since v5.8.
Links: [1] https://developer.arm.com/architectures/system-architectures/software-standards/scmi
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A regmap field is an abstraction available in Linux. It provides to access
bitfields in a regmap without having to worry about shifts and masks.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Some devices need to calculate the regmap base address at runtime. This
makes it impossible to use device tree to get the regmap base. Instead,
allow devices to specify it in the regmap config. This will create a
regmap with a single range that corresponds to the start and size given
by the driver.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Right now, the base of a regmap can only be obtained from the device
tree. This makes it impossible for devices which calculate the base at
runtime to use a regmap. An example of such a device is the Cadence
Sierra PHY.
Allow creating a regmap with one range whose start and size can be
specified by the driver based on calculations at runtime.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Drivers can configure it to adjust the final read/write location.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Right now, regmap_read() and regmap_write() read/write a 32-bit value
only. To write other lengths, regmap_raw_read() and regmap_raw_write()
need to be used.
This means that any driver ported from Linux that relies on
regmap_{read,write}() to know the size already has to be updated at each
callsite. This makes the port harder to maintain.
So, allow specifying the read/write width to make it easier to port the
drivers, since now the only change needed is when initializing the
regmap.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some fields will be introduced in the regmap structure that should be
set to 0 by default. So, once we allocate a regmap, make sure it is
zeroed out to avoid unexpected defaults for those values.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Most of new linux drivers are using managed-API to allocate resources. To
ease porting drivers from linux to U-Boot, introduce devm_regmap_init() as
a managed API to get a regmap from the device tree.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Add managed functions to get a gpio from the devce-tree, based on a
property name (minus the '-gpios' suffix) and optionally an index.
When the device is unbound, the GPIO is automatically released and the
data structure is freed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
The tests are basically the same as for the regular API. Except that
the reset are initialized using the managed API, and no freed manually.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Add managed functions to get a reset_ctl from the device-tree, based on a
name or an index.
Also add a managed functions to get a reset_ctl_bulk (array of reset_ctl)
from the device-tree.
When the device is unbound, the reset controllers are automatically
released and the data structure is freed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
- Disable CMD_IRQ for RISC-V.
- Update sipeed/maix doc
- Obtain reg of SiFive RAM via dev_read_addr_index() instead of regmap API.
- Cleans up RISC-V timer drivers and converts them to DM.
- Correctly handle IPIs already pending upon prior stage bootloader (on the K210)
There is no member `dev` in dw_mipi_dsi, but there is one in mipi_dsi_host,
so use that.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This driver does not use DM, so we need to use a struct device instead of a
struct udevice. Not ideal, but it'll have to do for now.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This can conflict with asm/io.h on some archs, and it isn't needed to build
dwc3-generic.c
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This driver does not use DM, so use log_xxx instead.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This logs with the device from struct dwc3. Some files also need to include
dm.h so fields in udevice can be accessed.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This adds a dev argument to some functions so dev_xxx always has a device
to log with. In one instance we must use use a different log function when
we are compiled without DM_USB.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
ep0.c also need to include dm.h so dev_xxx can access udevice fields.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Use `bus` instead of `dev`.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Remove the indirection.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Usually we can get a device from the current core, but some dev_dbg calls
have been converted to debug, since we are called on a cluster.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This function is never used anywhere, and it also tries to log with a
nonexistant device.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Use the phy's device.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
`phy` doesn't exist; we need to use `x` instead.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Get the device from phy, or pass the phy in.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Without DM_ETH, cpsw_priv.dev is an eth_device. Just use its name instead.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Pass a udevice into a few functions so `dev` is defined.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
There's no dev to log with, so pass the device along with the priv data.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
netdev_xxx evaluates to printf in U-Boot, so there is no extra info
printed. mvpp2 one of only two drivers which use these functions in U-Boot.
Convert these functions to dev_xxx where possible (and to log_xxx where
not).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Remove some prefixes, or get the device from the phy.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
netdev_xxx evaluates to printf in U-Boot, so there is no extra info
printed. mvneta is one of two drivers which use these functions in U-Boot.
Convert these functions to dev_xxx where possible (and to log_xxx where
not).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
No need for indirection here.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This member was presumably dropped when this driver was converted from
Linux. However, it is still used in log statements during initialization.
This patch adds the member back. In addition, allocation of struct
vf610_nfc has been moved to the callers of vf610_nfc_nand_init. This allows
it to be allocated by DM (if it is being used) and for dev to be
initialized.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
There are too many levels of indirection when calling dev_err. This is an
artifact of the conversion of brcmnand_host.pdev from a struct
platform_device (which has a member `dev` pointing to a struct device) to
struct udevice.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Use mtd_info to get a device to log with.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
dev needs to be gotten from mbox_chan
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This adds a udevice parameter to get_best_delay and msdc_set_mclk so they
can call dev_err properly.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Get it from spinand->slave->dev. Another option would be to use
spinand_to_mtd(spinand)->dev, but this is what the existing code uses.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This fixes dev_xxx() not always being called with a device. In
spi_nor_reg_read, a the slave device may not always be available, so we use
bus and cs instead.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This header is needed so struct udevice can be used in dev_xxx().
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Usually the device is gotten from sunxi_nfc. This is a struct device and
not a struct udevice, but the whole driver seems to be written wihout DM
anyway...
In a few instances, this patch modifies functions to take an nfc to log
with. In once instance we use mtd_info's device since there is no nfc.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Use the device from any mtd already available, or from the active mtd via
pxa3xx_nand_info if one is not.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
The udevice we are working with is called `bus` and not `dev`.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This converts calls to dev_err to get the device from ti_sci_info where
appropriate.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
We can't use dev_dbg here because we haven't bound to the device yet. Use
log_debug instead.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Another "virtual" clock (in the sense that it isn't configurable). This
could possibly be done as a clock in the device tree, but I think this is a
bit cleaner.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
To test this function, sandbox CPU must set cpu_platdata.timebase_freq on
bind. It also needs to expose a method to set the current cpu. I also make
some most members of cpu_sandbox_ops static.
On the timer side, the device tree property
sandbox,timebase-frequency-fallback controls whether sandbox_timer_probe
falls back to time_timebase_fallback or to SANDBOX_TIMER_RATE.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This function is designed to be used when a timer used to be initialized by
the cpu (e.g. RISC-V timers), but now is initialized by dm_timer_init. In
such a case, the timer may prefer to use the clocks and clock-frequency
properties, but should be able to fall back on using the cpu's
timebase-frequency.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The riscv-timer driver currently serves as a shim for several riscv timer
drivers. This is not too desirable because it bypasses the usual timer
selection via the driver model. There is no easy way to specify an
alternate timing driver, or have the tick rate depend on the cpu's
configured frequency. The timer drivers also do not have device structs,
and so have to rely on storing parameters in gd_t. Lastly, there is no
initialization call, so driver init is done in the same function which
reads the time. This can result in confusing error messages. To a user, it
looks like the driver failed when trying to read the time, whereas it may
have failed while initializing.
This patch removes the shim functionality from the riscv-timer driver, and
has it instead implement the former rdtime.c timer driver. This is because
existing u-boot users who pass in a device tree (e.g. qemu) do not create a
timer device for S-mode u-boot. The existing behavior of creating the
riscv-timer device in the riscv cpu driver must be kept. The actual reading
of the CSRs has been redone in the style of Linux's get_cycles64.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The usage of regmap API in the SiFive RAM driver is not correct.
The reg address should be obtained via dev_read_addr_index() API.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Fix a typo
%s/interract/interact/
Use Samsung's capitalization of their trademarks
%s/onenand/OneNAND/
%s/Hyperflash/HyperFlash/
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Add other Hyperflash cases as noted by Stefan]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for Microchip PIT64B timer. The timer is 64 bit length and
is used as a free running counter (in continuous mode with highest values
for period registers). The clock feeding the timer would be no more
than 12.5MHz.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
This fixes HWRNG support on Amlogic GXL, GXM, G12A, G12B & SM1
based boards dues to the lack of the core clock in the device tree.
It was reported breaking EFI boot in the Linux EFI stub, because the
EFI_RNG_PROTOCOL didn't check for the RNG device presence before
installing itself.
The Linux amlogic,meson-rng.yaml doesn't mandate the core clock,
this the clock should be ignores if not present.
Nevertheless, the clock should be present and this should be fixed
on the Linux meson-gxl.dtsi & meson-g12-common.dtsi then synced
with U-Boot.
The change has been tested on a Khadas VIM3, which uses the common
meson-g12-common.dtsi like the Odroid-C4 & Odroid-N2 in Scott's
report, along with the RNG cmd.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reported-by: Scott K Logan <logans@cottsay.net>
Fixes: bc40eb278b ("drivers/rng: add Amlogic hardware RNG driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Scott K Logan <logans@cottsay.net>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The micrel phy driver is already configuring this values from
device tree. So remove the redundant phy configuration call from
this driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
R8A774A1 is part of Renesas RZ/G2 series and not R-Car, reflect the same
for PINCTRL_PFC_R8A774A1 help description
Alongside, sort the PINCTRL_PFC_R8A774A1 config option as per increasing
number of the SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
- Enhance the 'zboot' command to be more like 'bootm' with sub-commands
- The last series of ACPI core changes for programmatic generation of
ACPI tables
- Add all required ACPI tables for ApolloLake and enable ACPIGEN on
Chromebook Coral
- A feature minor enhancements to the 'hob' command
- Intel edison: Support for writing an xFSTK image via binman
Call mmc_of_parse at probe time to fetch all the host properties
from the DT.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The second clock of the IP block (the generic clock), must be explicitly
enabled.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Peng Fan <pengfan@nxp.com>
clk_set_rate will return rate in case of success and zero in case of
error, however it can also return -ev, but it's an ulong function.
To avoid any issues, disregard the return value of this call.
In case this call actually fails, nothing much we can do anyway, but we
can at least try with the previous values (or DT assigned-clocks)
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add new compatibility string for matching sama7g5 product.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Many I2C devices produce roughly the same ACPI data with just things like
the GPIO/interrupt information being different.
This can be handled by a generic driver along with some information in the
device tree.
Add a generic i2c driver for this purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
LX2160A rev2 uses different PCIe controller, so EP mode DT
nodes also need to be fixed up.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_DM_SPI_FLASH is only supported now with passing of driver
conversion deadline from non-DM to DM model. Hence, it's safe to remove
non-DM code check from pfe_spi_flash_init.
Also use CONFIG_ENV_SPI_MODE and CONFIG_ENV_SPI_MAX_HZ instead of
reading reading values from DT.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix Coverity issue: RESOURCE_LEAK.
leaked_storage: Variable addr going out of scope leaks the storage it
points to.
Fixes: e0152dbed6 ("net: pfe_eth: Use spi_flash_read API to access
flash memory")
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
All the 10G ports that were working in XFI mode were described as
using XGMII (as PHY_INTERFACE_MODE_XFI was not added at the time).
Add the minimal changes required for the FMan code to support XFI.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
PFE DDR addresses are now stored on to a stack varaiable rather
dynamic allocation.
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
correction in delay implementation before we exit out of tx timeout.
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The next DPMAC was always verified if it is enabled. In case of
DPMAC@6, the DPMAC@7 is verified. As DPMAC@7 is disabled, DPMAC@6 will
be considered disabled and not detected by uboot.
Signed-off-by: Grigore Popescu <grigore.popescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX2x4MgAKCRDKSWXLKUoM
IZQtAJ9HpNwG5q3nHt9WedzLCTkr3YoLAACeJJ0Wlpp5p5xPzuPmnoo/Vi4MtNQ=
=yxRo
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.01
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
The info of fixed-link PHY is described in DT node instead of
getting from MII, so detect the fixed-link PHY DT node first,
if it doesn't exist then probe the MII.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
For the platforms on which the eTSEC driver uses DM_ETH, convert its
MDIO controller code to also use DM_MDIO.
Note that for handling the TBI PHY (the MAC PCS for SGMII), we still
don't register a udevice for it, since we can drive it locally and there
is no point in doing otherwise.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Reworked to fix gazerbeam config]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The MII management register block offset is different between
gianfar and etsec2 compatible devices, this patch is to fix
this issue by adding driver data for different compatible
string.
Fixes: 2932c5a802 ("net: tsec: fsl_mdio: add DM MDIO support")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Use virtual address to access the MII block registers instead
of physical address.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
It is utterly pointless to require an MDIO bus pointer for a fixed PHY
device. The fixed.c implementation does not require it, only
phy_device_create. Fix that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As required by PCI Express spec a delay for at least 100ms after
de-asserting PERST# signal is needed before link training is enabled.
Linux kernels prior to 5.8 version do not automatically disable link
training before de-asserting PERST# signal, therefore this requirement is
not fulfilled.
Above requirement is needed for proper detection of some Compex PCIe WiFi
cards. Otherwise Linux kernel cannot detect it.
To allow using those PCIe cards with older Linux kernel versions booted by
U-Boot compiled with U-Boot a37xx pci driver, disable link training in
U-Boot when unloading this pci driver.
Thanks to DM_FLAG_OS_PREPARE flag, U-Boot automatically unload this driver
when booting Linux kernel.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Some of Marvell A3700 boards use mx25u12835f, specifically uDPU
and ESPRESSObin v7.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
[a.heider: adapt commit message to mainline]
Signed-off-by: Andre Heider <a.heider@gmail.com>
The fdt_fixup_pcie_ls() scans all PCI devices and assumes that all PCI
root devices are layerscape PCIe controllers. Unfortunately, this is not
true for the LS1028A. There is one additional static PCI root complex
(this contains the networking devices) which has nothing to do with the
layerscape PCIe controllers. On recent U-Boot versions this results in
the following panic:
"Synchronous Abort" handler, esr 0x96000044
elr: 000000009602fa04 lr : 000000009602f9f4 (reloc)
elr: 00000000fbd73a04 lr : 00000000fbd739f4
x0 : 0080000002000101 x1 : 0000000000000000
x2 : 00000000fbde9000 x3 : 0000000000000001
x4 : 0000000000000000 x5 : 0000000000000030
x6 : 00000000fbdbd460 x7 : 00000000fbb3d3a0
x8 : 0000000000000002 x9 : 000000000000000c
x10: 00000000ffffffe8 x11: 0000000000000006
x12: 000000000001869f x13: 0000000000000a2c
x14: 00000000fbb3d2cc x15: 00000000ffffffff
x16: 0000000000010000 x17: 0000000000000000
x18: 00000000fbb3fda0 x19: 0000000000000800
x20: 0000000000000000 x21: 00000001f0000000
x22: 0000000000000800 x23: 0000000000000009
x24: 00000000fbdc3c1b x25: 00000000fbdc28e5
x26: 00000000fbdcc008 x27: 00000000fbdc16e2
x28: 000000000f000000 x29: 00000000fbb3d3a0
Code: 394072a1 f94006a0 34000041 5ac00a94 (b8336814)
Resetting CPU ...
This bug already existed in former versions, but the spurious write was
never trapped, because the destination address was a valid address (by
pure luck).
Make sure the PCI root is actually one of the expected PCIe layerscape
controllers by matching its compatible string.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
fixed-rate driver is not different from clk_fixed_factor and it is required
very early in boot that's why setup flag for it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
if conditions should match.
Fixes: a18d09ea38 ("fpga: zynqmp: Add secure bitstream loading for ZynqMP")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch does sed 's/SPL_FPGA_SUPPORT/SPL_FPGA/g' but also fixing Makefile
and zynqmp.c to simplify if/endif logic in zynqmp.c.
This change is mostly done to be able to use CONFIG_IS_ENABLED macro and
obj-$(CONFIG_$(SPL_)FPGA) in Makefile. For them symbols need to be in sync.
And removing one line from Topic Miami boards which is not needed because
symbol is not enabled via Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
flush_cache() arguments are not type casted to take care of 64 bit
systems. Use phys_addr_t to type cast for it to work properly for 32 bit
and 64 bit systems.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
There are compilation warnings showing up when we compile AXI ethernet
driver for 64bit architectures. Fix them, so that it works on both 32
and 64 bit architectures.
DMA descriptors are not taking care of 64bit addresses. To fix it,
change axidma_bd members as below:
next ==> next_desc
reserverd1 ==> next_desc_msb
phys ==> buf_addr
reserverd2 ==> buf_addr_msb
and update next_desc and buf_addr with lower 32 bits of the addresses,
update next_desc_msb and buf_addr_msb with upper 32 bits of the 64bit
addresses.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
NAND_ARASAN selecting DM_MTD uunconditionally. Driver can be enabled with
!DM that's why Kconfig it showing it as error:
WARNING: unmet direct dependencies detected for DM_MTD
Depends on [n]: DM [=n]
Selected by [y]:
- NAND_ARASAN [=y] && MTD_RAW_NAND [=y]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This endinness changes are taken from linux uartlite driver.
Reset TX fifo in control register and check TX fifo empty
flag in lower byte of the status register to detect if it
is a little endian system. Based on this check, program the
registers with le32 or be32 through out the driver.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynq/ZynqMP/Versal IPs should be possible to called also from Microblaze in
PL and vice versa. That's why change dependencies and do not limit enabling
just for some platforms.
This is follow up patch based on commit 664e16ce99 ("xilinx: kconfig:
Change Kconfig dependencies for Xilinx drivers").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Find out MDIO bus and enable MDIO access to it if this is done via
different GEM controller. Only works across GEM instances.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The most of drivers are using '_' instead of '-' in driver name. That's why
sync up these names to be aligned. It looks quite bad to see both in use.
It is visible via dm tree command.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The GPIO pins used by the SDHCI controller need to be configured to
allow the interface to work.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
The existing driver is not compatible with the Driver Model.
This patch makes the necessary changes while also removing obsolescent
calls/properties as follows:
- fdtdec_* calls replaced with dev_read_* equivalents;
- 'clock-freq-min-max' property replaced by querying the frequency of
the source clock 'base_clk';
- The card detect erratum workaround is applied during probe rather than
overriding get_cd.
The card detect workaround (Microchip ref. DS80000736E, erratum #15) is
not always needed and can be disabled using a vendor specific DT
property.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
In the live tree API ofnode_parse_phandle_with_args, the cell_count
argument must be used when cells_name is NULL.
But this argument is not provided to the live DT function
of_parse_phandle_with_args even it is provided to
fdtdec_parse_phandle_with_args.
This patch adds support of the cells_count parameter in dev_ and
of_node API to allow migration and support of live DT:
- of_parse_phandle_with_args
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix build failure, it used to get this implicitly through common.h
until f7ae49fc4f (common: Drop log.h from common header).
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Heiko Schocher <hs@denx.de>
Somewhere between v2020.04 and v2020.07 the mpc8xxx_spi driver broke,
I'm guessing due to this hunk
@@ -559,6 +560,8 @@ int dm_gpio_set_dir_flags(struct gpio_desc *desc, ulong flags)
if (ret)
return ret;
+ /* combine the requested flags (for IN/OUT) and the descriptor flags */
+ flags |= desc->flags;
ret = _dm_gpio_set_dir_flags(desc, flags);
from commit 695e5fd546 ("gpio: update dir_flags management"). But
the blame is mostly on the driver itself which seems rather confused:
The chip select gpios are requested with GPIOD_ACTIVE_LOW, but then in
each activate/deactivate, dm_gpio_set_dir_flags() is called with
merely GPIOD_IS_OUT, and then the driver call set_value(0) for
activate.
That used to work, but with the above hunk, the ACTIVE_LOW setting
from the request becomes persistent, so the gpio driver ends up being
asked to set the value to 1 in mpc8xxx_spi_cs_activate().
So drop the dm_gpio_set_dir_flags() calls in the activate/deactivate
functions, and use a value of 1 to mean "logically enabled".
Ideally, I think we should also drop the GPIOD_ACTIVE_LOW from the
request and make it up to the list of gpio cs in DT to indicate
whether that CS is enabled when driven low (as is of course usually
the case), but that requires changing
arch/powerpc/dts/gdsys/gazerbeam-base.dtsi among others, and I don't
have that hardware to test on. I have, however, tested our
own (mpc8309-based) hardware with this change, and I have also tested
that removing the GPIOD_ACTIVE_LOW from the request and updating our
DT as
- gpios = <&spisel 0 0>;
+ gpios = <&spisel 0 GPIO_ACTIVE_LOW>;
still works.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Add UTMI support for SAMA7G5. SAMA7G5's UTMI control is done via
XTALF register. Values written at bits 2..0 in this register
correspond to the on board crystal oscillator frequency.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add master clock (MCK1..MCK4) support for SAMA7G5. SAMA7G5's PMC has
multiple master clocks feeding different subsystems. One of them
feeds image subsystem and is changeable based on image subsystem
needs.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add sckc driver compatible with common clock framework. Driver
implements slow clock support for SAM9X60 compatible IPs (in this
list it is also present SAMA7G5's slow clock IP).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Move clock code to compat.c to allow switching to CCF
without mixing CCF code with non CCF code. This prepares the
field for next commits.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add helper for clock drivers. These will be used by following
commits in the process of switching AT91 clock drivers to CCF.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
clk_get_by_indexed_prop() retrieves a clock with dev member being set
with the pointer to the udevice for the clock controller driver. But
in case of CCF each clock driver has set in dev member the reference
to its parent (the root of the clock tree is a fixed clock, every
node in clock tree is a clock registered with clk_register()). In this
case the subsequent operations like dev_get_clk_ptr() on clocks
retrieved by clk_get_by_indexed_prop() will fail. For this, get the
pointer to the proper clock registered (with clk_register()) using
clk_get_by_id() before proceeding.
Fixes: 1d7993d1d0 ("clk: Port Linux common clock framework [CCF] for imx6q to U-boot (tag: v5.1.12)")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Clock re-parenting is not binding the clock's device to its new
parent device, it only calls the clock's ops->set_parent() API. The
changes in this commit re-parent the clock device to its new parent
so that subsequent operations like clk_get_parent() to point to the
proper parent.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In common clock framework the relation b/w parent and child clocks is
determined based on the udevice parent/child information. A clock
parent could be changed based on devices needs. In case this is happen
the functionalities for clock who's parent is changed are broken. Add
a function that reparent a device. This will be used in clk-uclass.c
to reparent a clock device.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The following bugs are fixed:
* incorrect online help for setenv and env
* description of function efi_mem_carve_out()
* replace printf() by log_err() in stm32mp1_rng driver
A unit test is provided to check that the boot hart id is provided in the
RISC-V device-tree.
-----BEGIN PGP SIGNATURE-----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=vhkz
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-10-rc5-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-10-rc5 (2)
The following bugs are fixed:
* incorrect online help for setenv and env
* description of function efi_mem_carve_out()
* replace printf() by log_err() in stm32mp1_rng driver
A unit test is provided to check that the boot hart id is provided in the
RISC-V device-tree.
The logging system provides flexible filtering and enhanced output.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Lot of Qualcomm SoC-s use DWC3 controller for both USB2.0 and USB3.0
ports.
Qualcomm has some custom config registers on top of the generic ones,
but for host mode these are not needed.
So lets add the neccessary compatible string.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Add a driver to setup the USB PHY-s on Qualcomm IPQ40xx series SoCs.
The driver sets up HS and SS phys.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
On Qualcomm IPQ40xx SoC series, GCC clock IP also handles the resets.
So since this will be needed by further drivers, lets add a driver for the reset controller.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
There is already existing driver for SMEM so lets enable it for IPQ40xx as well.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Currently, after config the clock rate, delay 10ms, this is quite a rough
method. Check the clock stable status in the present status register is
enough.
Tested-by: Ji Luo <ji.luo@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
add DM/DTS support for the UEC ethernet on QUICC Engine
Block.
Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Patch-cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Patch-cc: Madalin Bucur <madalin.bucur@oss.nxp.com>
Series-changes: 3
- revert:
commit "3374264df97b" ("drivers: net: qe: deselect QE when DM_ETH is enabled")
as now qe works with DM and DM_ETH support.
- fix mailaddress from Holger
Series-changes: 2
- add comments from Qiang Zhao:
- add device node documentation
- I did not drop the dm_qe_uec_phy.c and use drivers/net/fsl_mdio.c
because using drivers/net/fsl_mdio.c leads in none existent
udevice mdio@3320
instead boards with DM ETH support should use now this
driver.
- remove RFC tag
Commit-notes:
- I let the old none DM based implementation in code
so boards should work with old implementation.
This Code should be removed if all boards are converted
to DM/DTS.
- add the DM based qe uec driver under drivers/net/qe
- Therefore copied the files uccf.c uccf.h uec.h from
drivers/qe. So there are a lot of Codingstyle problems
currently. I fix them in next version if this RFC
patch is OK or it needs some changes.
- The dm based driver code is now under drivers/net/qe/dm_qe_uec.c
Used a lot of functions from drivers/qe/uec.c
- seperated the PHY specific code into seperate file
drivers/net/qe/dm_qe_uec_phy.c
END
add DM support for parallel I/O ports on QUICC Engine Block
Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Patch-cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Series-changes: 2
- remove RFC
- fixed Codingstyle errors, therefore new patch
powerpc, mpc83xx: fix codingstyle issues for qe_io.c
- moved DM part to drivers/pinctrl
Commit-notes:
Open questions / discussion:
- I let the old none DM based implementation in code
so boards should work with old implementation.
This should be removed if all boards are converted to
DM/DTS.
- Unfortunately linux DTS does not use "pinctrl-"
properties, instead "pio-handle" properties.
Even worser old U-Boot code initializes all pins
defined in "const qe_iop_conf_t qe_iop_conf_tab[]"
table in board code. As linux does the same I decided
to also scan through all subnodes containing "pio-map"
property and initialize them too.
The proper solution would be to check for "pio-handle"
when a device is probed.
END
- Hyperflash boot for J7200
- Update Main R5FSS lockstep mode
- R5F remoteproc support for J7200
- Minor env fixes
- Add SPI boot support for am335x-icev2
Add an ofdata_to_platdata() callback to access dts in U-boot and
access all platform data in it. This prepares the driver for supporting
both device tree as well as static platform data structures in SPL.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Add platform data and a device structure for the spi device
present on am335x-icev2. This requires moving all omap3_spi
platform data structures and symbols to an omap3_spi.h so that
the board file can access them.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
There are devices which don't use OF_CONTROL or OF_PLATDATA but instead
rely on statically defined platdata. Block dm_scan_fdt_dev() with both
configs to avoid build failures under this condition.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The K3 J7200 SoC family has a revised R5F sub-system and contains a
subset of the R5F clusters present on J721E SoCs. The integration of
these clusters is very much similar to J721E SoCs otherwise.
The revised IP has the following two new features:
1. TCMs are auto-initialized during module power-up, and the behavior
is programmable through a MMR bit controlled by System Firmware.
2. The LockStep-mode allows the Core1 TCMs to be combined with the
Core0 TCMs effectively doubling the amount of TCMs available.
The LockStep-mode on previous SoCs could only use the Core0 TCMs.
This combined TCMs appear contiguous at the respective Core0 TCM
addresses.
Add the support to these clusters in the K3 R5F remoteproc driver
using J7200 specific compatibles and revised logic accounting for
the above IP features/differences.
Signed-off-by: Suman Anna <s-anna@ti.com>
Use mmc_of_parse() to set the common host properties. That includes
"bus-width", so parsing it can be removed from the driver.
But more importantly, "non-removable" is now respected, which fixes
the usage of eMMC.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Tested-by: Marek Behún <marek.behun@nic.cz>
Since the introduction of 'get_cd' callback in sdhci core,
dragonboard410c's MMC interface is broken. It turns out that 'get_cd'
callback checks for the host_caps for validating the chip select. And
since the msm_sdhci driver is not parsing the host_caps from DT, not
all of the cababilities are parsed properly. This results in the MMC
interfaces to be broken.
Hence, fix this by adding a call to 'mmc_of_parse' during driver probe.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Aníbal Limón <anibal.limon@linaro.org>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Nand writes should skip the bad blocks with "nand write" command.
In case of bad blocks with above 32-bit address, nand_block_isbad()
returns false due to truncated bad block address.
In below code segment,
if (nand_block_isbad(mtd, offset & ~(mtd->erasesize - 1)))
offset is 64-bit and mtd->erasesize is 32-bit, hence the truncation is
happening. Cast 'mtd->erasesize' with loff_t to fix this issue.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
On the mt7623 platform, if one port enable fail and other port
enable succeed. It will hang on when using pci enum
because the resource was not released correctly.
Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
On the mt7623 platform, if one port enable fail and other port
enable succeed. It will hang on when using pci enum
because the resource was not released correctly.
Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
v2: modify title description aspeed:clock -> clock:aspeed
Use kernel include/dt-bindings/clock/aspeed-clock.h define
for clock driver.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Reviewed-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Rename the ast2500-scu.h to aspeed-clock.h.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Reviewed-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The commit 57805f2270 ("net: bcmgenet: Don't set ID_MODE_DIS when
not using RGMII") needed to be extended for the case of using the
rgmii-rxid. The latest version of the Rasbperry Pi4 dtb files for the
5.4 now specify the rgmii-rxid.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Tested-by: Petr Tesarik <ptesarik@suse.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
This commit fixes a serious issue occurring when several network
commands are run on a raspberry pi 4 board: for instance a "dhcp"
command and then one or several "tftp" commands. In this case,
packet recv callbacks were called several times on the same packets,
and send function was failing most of the time.
note: if the boot procedure is made of a single network
command, the issue is not visible.
The issue is related to management of the packet ring buffers
(producer / consumer) and DMA.
Each time a packet is received, the ethernet device stores it
in the buffer and increments an index called RDMA_PROD_INDEX.
Each time the driver outputs a received packet, it increments
another index called RDMA_CONS_INDEX.
Between each pair of network commands, as part of the driver
'start' function, previous code tried to reset both RDMA_CONS_INDEX
and RDMA_PROD_INDEX to 0. But RDMA_PROD_INDEX cannot be written from
driver side, thus its value was actually not updated, and only
RDMA_CONS_INDEX was reset to 0. This was resulting in a major
synchronization issue between the driver and the device. Most
visible behavior was that the driver seemed to receive again the
packets from the previous commands (e.g. DHCP response packets
"received" again when performing the first TFTP command).
This fix consists in setting RDMA_CONS_INDEX to the same
value as RDMA_PROD_INDEX, when resetting the driver.
The same kind of fix was needed on the TX side, and a few variables
had to be reset accordingly (c_index, tx_index, rx_index).
The rx_index and tx_index have only 256 entries so the bottom 8 bits
must be masked off.
Originated-by: Etienne Dublé <etienne.duble@imag.fr>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Tested-by: Petr Tesarik <ptesarik@suse.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
As the error message is now displayed by generic phy functions,
the dev_err/pr_err can be change to dev_dbg/pr_debug.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
As the error message is now displayed by generic phy functions,
the pr_err can be change to pr_debug.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
As the error message is now displayed by generic phy functions,
the pr_err can be change to pr_debug.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
As the error message is now displayed by generic phy functions,
the dev_err can be change to dev_dbg.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- This patch moves sata phy powerup from dedicate phy to compphy
and adds invert option for sata powerup routine.
Change-Id: I1b4e8753e2b2c14c6efa97bca2ffc7d2553d8a90
Signed-off-by: zachary <zhangzg@marvell.com>
Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/53601
Reviewed-by: Igal Liberman <igall@marvell.com>
Tested-by: Igal Liberman <igall@marvell.com>
[a.heider: adapt to mainline]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The size returned by 'getvar partition-size' should be in bytes, not in
blocks as fastboot uses that value to generate empty partition when
running format [1].
Note that the function was already returning the proper size in bytes
for NAND devices (see struct part_info details).
[1]
https://android.googlesource.com/platform/system/core/+/refs/heads/android10-release/fastboot/fastboot.cpp#1500
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
It was revealed that when the fastboot_tx_write_str function is called
without the previously initialized fastboot_func->in_req->complete field,
a copy of in_req will be sent to the I/O requests queue without
an initialized field.
Moving a piece of code with the initializing of the
fastboot_func->in_req->complete field above transmit_tx allows to solve
this problem.
Fixes: 65c96757fe "usb: fastboot: Convert USB f_fastboot to shared fastboot"
Signed-off-by: yurii.pidhornyi <yurii.pidhornyi@globallogic.com>
Since the USB HID limits the maximum bandwidth(3072) for interrupt
endpoint transfers, when the bInterval set to 1, we can only support 3
boards to run sdp at the same time. In order to support more boards,
change the bInterval of interrupt endpoint to 3, which will not affect
the transmission speed.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
EP0 has been used to transfer file data in sdp before, but the max
packetsize of ep0 is 64 bytes. So in order to improve the file transfer
speed, here add the EP1_OUT interrupt endpoint which max packetsize is
set to 1024 byte.
After testing, it turns out that using ep1out is twice as fast as using
ep0 while receiving data in sdp.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support to f_sdp to search and load iMX8 container image or iMX8M
FIT image by new UUU command SDPV.
When using the SDPV, the uuu will continue to send out data after first
level boot loader used by ROM. This means uuu won't skip to the offset
of the second boot loader, and the padding data before second boot loader
will be sent out. So we have to search the FIT header or container header
in the buffer that SDP received.
Also change to more common method to exit f_sdp handler not depending on
SPL_FIT_FOUND flag because container loader won't set this.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Because the buffer length of sdp usb request is 65, we have to allocate
65 bytes not 64 bytes. Otherwise there is potential buffer overflow.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>