Bob is a 10-inch chromebook produced by Asus. It has two USB 3.0 type-C
ports, 4GB of SDRAM, WiFi and a 1280x800 display. It uses its USB ports
for both power and external display. It includes a Chrome OS EC
(Cortex-M3) to provide access to the keyboard and battery functions.
Support so far includes only:
- UART
- SDRAM
- MMC, SD card
- Cros EC (but not keyboard)
Not included:
- Keyboard
- Display
- Sound
- USB
- TPM
Bob is quite similar to Kevin, the Samsung Chromebook Plus, but support
for this is not provided in this series.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add mention of a prerequisite needed to build the image. Also adjust the
English wording in a few places.
Ideally this should move to using binman to produce images, and avoid the
manual steps.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This adds support for the ASUS C201, a RK3288-based clamshell
device. The device tree comes from linus's linux tree at
3f16503b7d2274ac8cbab11163047ac0b4c66cfe. The SDRAM parameters
are for 4GB Samsung LPDDR3, decoded from coreboot's
src/mainboard/google/veyron/sdram_inf/sdram-lpddr3-samsung-4GB.inc
Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
port the am335x based shc board to DM, to get rid
of DW warnings when compiling U-Boot.
- remove uneccessary board code
- adapt defconfigs
- remove unneeded defconfigs
configs/am335x_shc_prompt_defconfig
configs/am335x_shc_sdboot_prompt_defconfig
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
add u-boot specific am335x-shc-u-boot.dtsi file,
in which we add u-boot specific adaptions.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
add DTS from linux tree commit
"47bfa6d9dc8c060bf56554a465c9031e286d2f80"
change for U-Boot:
switch to SPDX-license identifier.
Signed-off-by: Heiko Schocher <hs@denx.de>
When power cycle the Jaguar2 boards, it couldn't read the
phys, therefore it always deduce that the board type is
pcb111.
Add a small delay after setting the gpio pins, fix the
issue.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Enabling DM_MMC skips the call to mmc_pinmux_setup() in board.c, as this
is supposed to be handled by the MMC driver, using DT information.
However we don't have a pinctrl driver yet, but would still like to keep
the working pinmux setup for our MMC devices. So bring this particular
call back to the DM_MMC code flow.
When booting from either SD card or eMMC, the SPL does the setup for us,
but when booting from SPI or USB we must not skip this part.
Fixes, boot via FEL or SPI flash, where the SPL won't setup the pinmux
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@openedev.com>
[jagan: add Fix details on commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This patch enables Falcon Mode by default and updates the README
file to show instructions on how to run from the micro SD card
or eMMC. This patch also enables fatwrite to help assist with
writing the 'args' to the microSD card.
Signed-off-by: Adam Ford <aford173@gmail.com>
The i.MX6 SOM and development kits have undergone significant
updates and changes over the past few months. This re-sync's
the U-Boot with Logic PD's BSP.
Signed-off-by: Adam Ford <aford173@gmail.com>
The MMC booting wasn't previously fitting into the codespace.
This patch enables MMC booting from the baseboard by reducing
some DM overhead during SPL.
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch converts the warp7 and warp7_bl33 board ports over to using the
DM PMIC model.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
There is no need to set the ARCH variable when building U-Boot. In fact,
the ARCH name in U-Boot is 'arm'.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Enable SPL for i.MX8QXP MEK, and currently use SPL FIT.
The SPL enable SPL_DM to use MMC/PINCTRL/POWER DOMAIN/CLK.
Note: SPL FIT could not support secure boot chain, because i.MX8/8X
only support i.MX container format. This container format has
not been upstreamed, so we use FIT for now. When SPL container
supported, we could switch to that.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In preparation of adding CONFIG_DM_MMC support use separate device
trees for raw NAND and eMMC devices.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add support for the VXT VL050-8048NT-C01 panel connected through
the 24 bit parallel LCDIF interface.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Port for the PHYTEC phyBOARD-i.MX6UL-Segin single board computer. Based on
the PHYTEC phyCORE-i.MX6UL SOM (PCL063).
CPU: Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 44C
Reset cause: POR
Board: PHYTEC phyCORE-i.MX6UL
I2C: ready
DRAM: 256 MiB
NAND: 512 MiB
MMC: FSL_SDHC: 0
In: serial
Out: serial
Err: serial
Net: FEC0
Working:
- Eth0
- i2C
- MMC/SD
- NAND
- UART (1 & 5)
- USB (host & otg)
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Make use of "IMAGE_MAX_SIZE" and "IMAGE_TEXT_BASE" rather than
CONFIG_SPL_MAX_SIZE and CONFIG_SPL_TEXT_BASE. This lets us re-use the
same script for both SPL and TPL. Add logic to scripts/Makefile.spl to
pass in the right value when preprocessing the script.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850evm & omap3_logic_somlv
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
We have converted mmc to driver model on Poplar. So let's clean up
board level mmc initialization code.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The miamiplus can use GEM0 through MIO pins, which requires a 125 MHz TX
clock to be generated. With the IO PLL at 1200 MHz this isn't possible, so
change it to run at 1000 and adjust the divisors accordingly. Also set the
GEM0 clock source to MIO instead of EMIO.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The miamiplus contains a speedgrade-2 device, which may run the CPU at 800MHz.
Change the PLL setting to 800MHz, and adapt the setpoints in the devicetree.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patches renames sd nodes in dts to be in line with
kernel. This patch also modifies the references for the same
in code.
It checks mmc first to have no time penalty for new DT node names based
on left-to-right expression evaluation.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add board support and configuration for Jaguar2 SoC family.
The detection of the board type is based on the phy ids.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add board support, configuration and DTS for Servalt SoC
family. Currently there is one board in this family.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
On some ocelots platform a workaround is needed in order to be able to
reset the switch without resetting the DDR.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This is a range of stackable network switches. The SoC is Armada-385 and
there are a number of variants with differing network port
configurations. The DP variants are intended for a harsher operating
environment so they use a different i2c mux and fit industrial-temp
parts.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
These macros are not used anywhere in the boards code.
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Use get_ram_size to determine if the RAM size on Turris Mox is 512 MiB
or 1 GiB.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for reading One-Time Programmable memory via mailbox, which
communicates with CZ.NIC's firmware on the Secure Processor (Cortex-M3)
of Armada 3720.
Display product serial number and additional info, and also set MAC
addresses.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Check if Mox modules are connected in supported mode, then configure
the MDIO addresses of switch modules.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
When SFP module is connected directly to CPU module we want the SGMII
lane speed at 1.25 Gbps.
This is a temporary solution till there is a comphy driver in the kernel
capable of changing SGMII speed at runtime.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Restructure the board initialization source.
Remove the module_topology environment variable since it won't be
needed.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Emlid Neutis N5 is a SoM based on Allwinner H5, has a WiFi & BT
module, DDR3 RAM and eMMC.
- add neutis-devboard target to dtb makefile
- add dtsi file for Neutis N5 needs
- add config file for Neutis N5 Dev board
Signed-off-by: Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: update proper commit head]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
To use TWI0/1/2 the user can select CONFIG_I2C#_ENABLE.
However even the controller is enabled, the mux for the pins
are not set.
This patch follows the existing mux method. Since the pads are
different, separate check is added for each i2c.
Tested with A64-SOM204 board.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
am43xx_evm_ethboot_defconfig is not being actively used and has not been
moved to DM or DT. Also, ethboot cannot be tested on AM43xx EVM as such
due EVM limitations. Therefore delete it.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These defconfigs don't seem be actively used any more, and have not been
moved to adapt DM or DT. Therefore delete them.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
bananapi r2 can be booted from sd-card and emmc
saving the environment have to choose the storage
from which the device has booted
also the offset is set to 1MB to make sure env is written
to block "user data area" between uboot and first partition
https://www.fw-web.de/dokuwiki/lib/exe/fetch.php?cache=&media=bpi-r2:boot-structure.png
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
u-boot makes a fixup for LS1046AQDS board to setup the properties
'fixed-link' and 'phy-connection-type' to 'xgmii' but in case of
backplane mode this fixup is not correct because it causes the KR link
to fail and so it must be bypassed in order to keep the link in KR
mode as it is defined in DTS.
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
[YS: Fix compiling warning]
Reviewed-by: York Sun <york.sun@nxp.com>
fsl-mc lazyapply command applies dpl from efi_exit_boot_services().
Status of fsl-mc node in working fdt is updated at this stage.
However, an efi application like grub may already have copied the fdt.
So the updates to fdt done at efi_exit_boot_services() may not be
visible to the OS. Fix it by updating fdt earlier if fsl-mc lazyapply
command is used.
Fixes: b7b8410a8f (ls2080: Exit dpaa only right before exiting U-Boot)
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls2088aqds_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls2088ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- remove EL3 specific erratas for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1088aqds_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- MC address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- ifc chip select changes for TFABOOT
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1088ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- MC address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- ifc chip select changes for TFABOOT
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add board support and configuration for Jaguar2 SOC family.
The detection of the board type in this family is based on the phy ids.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
This enables the use of the MSCC serial GPIO driver to control the
LEDs on the MSCC VCoreIII 'ocelot' pcb123 and pcb120.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
This enables the use of the MSCC serial GPIO driver to control the
LEDs on the MSCC VCoreIII 'luton' SoC.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
As we are moving to multi-dtb and board detection, remove static board
config options, and introduce board probing instead.
Luton: This add single-binary support for the two MSCC luton-based
reference boards - pcb090 and pcb091. The SoC chip ID is used to
determine the board type.
Ocelot: This add single-binary support for the two MSCC ocelot-based
reference boards - pcb120 and pcb123. The PHY ids on specific ports
are used to determine the board type.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
The IGEP0032 board was never officially pushed upstream and actually I
don't have access to this hardware, unless someone with the hardware
wants to start working on this doesn't makes sense have this defconfig
here. So remove it.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
It enables DWC2 OTG gadget driver support for Poplar board. As
usb2_phy_init() is being always called from board_init(), we can save
the call from board_usb_init().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Commit 3f353ceccb ("vf610: refactor DDRMC code") changed on-die
termination (ODT) values from 120 Ohm to 60 Ohm and enabled a static
read/write leveling which has not been tested with this board. This
commit reverts both changes and makes sure that memory gets
initialized as it has been done before the mentioned commit.
Fixes: 3f353ceccb ("vf610: refactor DDRMC code")
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
I can't continue maintaining the board because I don't have access to the
hardware anymore, so remove myself from the entry and add Javier who has
volunteered to help and maintain the board.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Javier Martínez Canillas <javier@dowhile0.org>
Merge functionality duplicated in bx50v3 and mx53ppd: the logic
is the same except that process_vpd is called at different phases.
Also read_vpd could end up in error, so there is no VPD data in this
case - it shouldn't be processed.
Signed-off-by: Denis Zalevskiy <denis.zalevskiy@ge.com>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
Commit a8011eb84dfa("sunxi: board: Print error after power initialization
fails") moved the DRAM init after the increase of the CPU clock
frequency. This lead to various DRAM initialisation failures on some
boards (hangs or wrong size reported, on a NanoPi Duo2 and OrangePi
Zero, for instance). Lowering the CPU frequency significantly (for instance
to 408 MHz) seems to work around the problem, so this points to some timing
issues in the DRAM code.
Debugging this sounds like a larger job, so let's just revert this patch
to bring back those boards.
Beside this probably unintended change the patch just moved the error
message around, so reverting this is not a real loss.
This reverts commit a8011eb84d.
Tested-By: Priit Laes <plaes@plaes.org>
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add support for the Creator CI20 platform based on the JZ4780 SoC.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Adding the support for the Luton boards PCB91 which share common code with
the Ocelots boards, including board code, device tree and configuration.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Remove cpu name from the defconfig naming.
Because other cpus maybe run on AE350 platform.
So only use platfrom name in defconfig naming
will be better.
Also sync MAINTAINERS:
Rename
a25-ae350_32_defconfig as ae350_rv32_defconfig
ax25-ae350_64_defconfig as ae350_rv64_defconfig
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch enables SiFive UART driver for QEMU RISC-V emulation
by implying SIFIVE_SERIAL on BOARD_SPECIFIC_OPTIONS.
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Add the QEMU RISC-V platform-specific Kconfig options, to include
CPU and timer drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
There is no need to expose RISCV_NDS to the Kconfig menu as it is
an ax25-specific option. Introduce a dedicated Kconfig option for
the cache ops of ax25 platform and use that to guard the cache ops.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Rick Chen <rick@andestech.com>
Use standard configuration logic to define EEPROM constants.
Names are based on VPD_EEPROM_ prefix because EEPROM_ is already
used by i2c_eeprom driver.
Signed-off-by: Denis Zalevskiy <denis.zalevskiy@ge.com>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
The bus is statically defined, so remove redundant parameters
from read_vpd() for PPD and Bx50v3.
Signed-off-by: Denis Zalevskiy <denis.zalevskiy@ge.com>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
Add the initial support for Elgin R1 board, which is based on the
RV1108 SoC and has the following features currently supported in
U-Boot:
- UART
- eMMC
- USB
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Commit 4687919684 ("serial: Remove DM_FLAG_PRE_RELOC flag in various
drivers") essentially drops flag DM_FLAG_PRE_RELOC from serial_pl01x
driver for Poplar platform, because the platform falls into the
following strategy category made by the commit.
Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Before the commit lands, Poplar platform works by statically declaring
pl011 serial device via U_BOOT_DEVICE() with DM_FLAG_PRE_RELOC flag set
in the driver. But since Poplar also supports device configuration from
device tree, the commit practically drops the flag for Poplar, and hence
breaks the platform from booting.
This patch changes platform code and device tree to initiate pl011
serial device from device tree rather than static declaration, so that
above strategy about DM_FLAG_PRE_RELOC applies to Poplar, and therefore
the reported boot failure gets fixed.
Reported-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Fixes: 4687919684 ("serial: Remove DM_FLAG_PRE_RELOC flag in various drivers")
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Tested-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable USB clocks in late init stage to support ports under DM_USB.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
I had requested the da850 boards because their previous maintainer
had an invalid e-mail address. I work at Logic PD who makes
the da850-evm kits, so I have access to various boards of theirs.
The Spectrum Digital AM18xx board is based on the Logic PD
da850 EVM, but it's not the same company. Since I don't have the
hardware to test/verify changes, I would prefer to not be
responsible for this board.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add support for lx2160a SoC
-----BEGIN PGP SIGNATURE-----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=aT7d
-----END PGP SIGNATURE-----
Merge tag 'fsl-qoriq-for-v2019.01-rc2' of git://git.denx.de/u-boot-fsl-qoriq
Add TFA boot flow for some Layerscape platforms
Add support for lx2160a SoC
[trini: Add a bunch of missing MAINTAINERS entries]
Signed-off-by: Tom Rini <trini@konsulko.com>
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C
API when DM_I2C is used. The goal is to eventually remove DM_I2C_COMPAT
when all I2C "clients" have been migrated to use the DM API.
This a step in that direction for the TI based platforms.
Build tested with buildman:
buildman -dle am33xx ti omap3 omap4 omap5 davinci keystone
boot tested with:
am335x_evm, am335x_boneblack, am335x_boneblack_vboot (DM version),
am57xx_evm, dra7xx_evm, k2g_evm, am437x_evm
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
