mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-06-09 23:36:03 +09:00
arm: mvebu: turris_mox: Check and configure modules
Check if Mox modules are connected in supported mode, then configure the MDIO addresses of switch modules. Signed-off-by: Marek Behún <marek.behun@nic.cz> Signed-off-by: Stefan Roese <sr@denx.de>
This commit is contained in:
Marek Behún
Stefan Roese
parent
9433cd1109
commit
7dd7c2e796
|
|
@ -110,6 +110,17 @@
|
|||
spi-max-frequency = <20000000>;
|
||||
m25p,fast-read;
|
||||
};
|
||||
|
||||
moxtet@1 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
compatible = "cznic,moxtet";
|
||||
reg = <1>;
|
||||
reset-gpios = <&gpiosb 2 GPIO_ACTIVE_LOW>;
|
||||
spi-max-frequency = <1000000>;
|
||||
spi-cpol;
|
||||
spi-cpha;
|
||||
};
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
|
|
|
|||
|
|
@ -4,11 +4,13 @@
|
|||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <asm/gpio.h>
|
||||
#include <asm/io.h>
|
||||
#include <dm.h>
|
||||
#include <clk.h>
|
||||
#include <spi.h>
|
||||
#include <mvebu/comphy.h>
|
||||
#include <miiphy.h>
|
||||
#include <linux/string.h>
|
||||
#include <linux/libfdt.h>
|
||||
#include <fdt_support.h>
|
||||
|
|
@ -239,11 +241,138 @@ int comphy_update_map(struct comphy_map *serdes_map, int count)
|
|||
return 0;
|
||||
}
|
||||
|
||||
#define SW_SMI_CMD_R(d, r) (0x9800 | (((d) & 0x1f) << 5) | ((r) & 0x1f))
|
||||
#define SW_SMI_CMD_W(d, r) (0x9400 | (((d) & 0x1f) << 5) | ((r) & 0x1f))
|
||||
|
||||
static int sw_multi_read(struct mii_dev *bus, int sw, int dev, int reg)
|
||||
{
|
||||
bus->write(bus, sw, 0, 0, SW_SMI_CMD_R(dev, reg));
|
||||
mdelay(5);
|
||||
return bus->read(bus, sw, 0, 1);
|
||||
}
|
||||
|
||||
static void sw_multi_write(struct mii_dev *bus, int sw, int dev, int reg,
|
||||
u16 val)
|
||||
{
|
||||
bus->write(bus, sw, 0, 1, val);
|
||||
bus->write(bus, sw, 0, 0, SW_SMI_CMD_W(dev, reg));
|
||||
mdelay(5);
|
||||
}
|
||||
|
||||
static int sw_scratch_read(struct mii_dev *bus, int sw, int reg)
|
||||
{
|
||||
sw_multi_write(bus, sw, 0x1c, 0x1a, (reg & 0x7f) << 8);
|
||||
return sw_multi_read(bus, sw, 0x1c, 0x1a) & 0xff;
|
||||
}
|
||||
|
||||
static void sw_led_write(struct mii_dev *bus, int sw, int port, int reg,
|
||||
u16 val)
|
||||
{
|
||||
sw_multi_write(bus, sw, port, 0x16, 0x8000 | ((reg & 7) << 12)
|
||||
| (val & 0x7ff));
|
||||
}
|
||||
|
||||
static void sw_blink_leds(struct mii_dev *bus, int peridot, int topaz)
|
||||
{
|
||||
int i, p;
|
||||
struct {
|
||||
int port;
|
||||
u16 val;
|
||||
int wait;
|
||||
} regs[] = {
|
||||
{ 2, 0xef, 1 }, { 2, 0xfe, 1 }, { 2, 0x33, 0 },
|
||||
{ 4, 0xef, 1 }, { 4, 0xfe, 1 }, { 4, 0x33, 0 },
|
||||
{ 3, 0xfe, 1 }, { 3, 0xef, 1 }, { 3, 0x33, 0 },
|
||||
{ 1, 0xfe, 1 }, { 1, 0xef, 1 }, { 1, 0x33, 0 }
|
||||
};
|
||||
|
||||
for (i = 0; i < 12; ++i) {
|
||||
for (p = 0; p < peridot; ++p) {
|
||||
sw_led_write(bus, 0x10 + p, regs[i].port, 0,
|
||||
regs[i].val);
|
||||
sw_led_write(bus, 0x10 + p, regs[i].port + 4, 0,
|
||||
regs[i].val);
|
||||
}
|
||||
if (topaz) {
|
||||
sw_led_write(bus, 0x2, 0x10 + regs[i].port, 0,
|
||||
regs[i].val);
|
||||
}
|
||||
|
||||
if (regs[i].wait)
|
||||
mdelay(75);
|
||||
}
|
||||
}
|
||||
|
||||
static void check_switch_address(struct mii_dev *bus, int addr)
|
||||
{
|
||||
if (sw_scratch_read(bus, addr, 0x70) >> 3 != addr)
|
||||
printf("Check of switch MDIO address failed for 0x%02x\n",
|
||||
addr);
|
||||
}
|
||||
|
||||
static int sfp, pci, topaz, peridot, usb, passpci;
|
||||
static int sfp_pos, peridot_pos[3];
|
||||
static int module_count;
|
||||
|
||||
static int configure_peridots(struct gpio_desc *reset_gpio)
|
||||
{
|
||||
int i, ret;
|
||||
u8 dout[MAX_MOX_MODULES];
|
||||
|
||||
memset(dout, 0, MAX_MOX_MODULES);
|
||||
|
||||
/* set addresses of Peridot modules */
|
||||
for (i = 0; i < peridot; ++i)
|
||||
dout[module_count - peridot_pos[i]] = (~i) & 3;
|
||||
|
||||
/*
|
||||
* if there is a SFP module connected to the last Peridot module, set
|
||||
* the P10_SMODE to 1 for the Peridot module
|
||||
*/
|
||||
if (sfp)
|
||||
dout[module_count - peridot_pos[i - 1]] |= 1 << 3;
|
||||
|
||||
dm_gpio_set_value(reset_gpio, 1);
|
||||
mdelay(10);
|
||||
|
||||
ret = mox_do_spi(NULL, dout, module_count + 1);
|
||||
|
||||
mdelay(10);
|
||||
dm_gpio_set_value(reset_gpio, 0);
|
||||
|
||||
mdelay(50);
|
||||
|
||||
return ret;
|
||||
}
|
||||
|
||||
static int get_reset_gpio(struct gpio_desc *reset_gpio)
|
||||
{
|
||||
int node;
|
||||
|
||||
node = fdt_node_offset_by_compatible(gd->fdt_blob, 0, "cznic,moxtet");
|
||||
if (node < 0) {
|
||||
printf("Cannot find Moxtet bus device node!\n");
|
||||
return -1;
|
||||
}
|
||||
|
||||
gpio_request_by_name_nodev(offset_to_ofnode(node), "reset-gpios", 0,
|
||||
reset_gpio, GPIOD_IS_OUT);
|
||||
|
||||
if (!dm_gpio_is_valid(reset_gpio)) {
|
||||
printf("Cannot find reset GPIO for Moxtet bus!\n");
|
||||
return -1;
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
int last_stage_init(void)
|
||||
{
|
||||
int ret, i;
|
||||
const u8 *topology;
|
||||
int module_count, is_sd;
|
||||
int is_sd;
|
||||
struct mii_dev *bus;
|
||||
struct gpio_desc reset_gpio = {};
|
||||
|
||||
ret = mox_get_topology(&topology, &module_count, &is_sd);
|
||||
if (ret) {
|
||||
|
|
@ -278,6 +407,109 @@ int last_stage_init(void)
|
|||
}
|
||||
}
|
||||
|
||||
/* now check if modules are connected in supported mode */
|
||||
|
||||
for (i = 0; i < module_count; ++i) {
|
||||
switch (topology[i]) {
|
||||
case MOX_MODULE_SFP:
|
||||
if (sfp) {
|
||||
printf("Error: Only one SFP module is supported!\n");
|
||||
} else if (topaz) {
|
||||
printf("Error: SFP module cannot be connected after Topaz Switch module!\n");
|
||||
} else {
|
||||
sfp_pos = i;
|
||||
++sfp;
|
||||
}
|
||||
break;
|
||||
case MOX_MODULE_PCI:
|
||||
if (pci) {
|
||||
printf("Error: Only one Mini-PCIe module is supported!\n");
|
||||
} else if (usb) {
|
||||
printf("Error: Mini-PCIe module cannot come after USB 3.0 module!\n");
|
||||
} else if (i && (i != 1 || !passpci)) {
|
||||
printf("Error: Mini-PCIe module should be the first connected module or come right after Passthrough Mini-PCIe module!\n");
|
||||
} else {
|
||||
++pci;
|
||||
}
|
||||
break;
|
||||
case MOX_MODULE_TOPAZ:
|
||||
if (topaz) {
|
||||
printf("Error: Only one Topaz module is supported!\n");
|
||||
} else if (peridot >= 3) {
|
||||
printf("Error: At most two Peridot modules can come before Topaz module!\n");
|
||||
} else {
|
||||
++topaz;
|
||||
}
|
||||
break;
|
||||
case MOX_MODULE_PERIDOT:
|
||||
if (sfp || topaz) {
|
||||
printf("Error: Peridot module must come before SFP or Topaz module!\n");
|
||||
} else if (peridot >= 3) {
|
||||
printf("Error: At most three Peridot modules are supported!\n");
|
||||
} else {
|
||||
peridot_pos[peridot] = i;
|
||||
++peridot;
|
||||
}
|
||||
break;
|
||||
case MOX_MODULE_USB3:
|
||||
if (pci) {
|
||||
printf("Error: USB 3.0 module cannot come after Mini-PCIe module!\n");
|
||||
} else if (usb) {
|
||||
printf("Error: Only one USB 3.0 module is supported!\n");
|
||||
} else if (i && (i != 1 || !passpci)) {
|
||||
printf("Error: USB 3.0 module should be the first connected module or come right after Passthrough Mini-PCIe module!\n");
|
||||
} else {
|
||||
++usb;
|
||||
}
|
||||
break;
|
||||
case MOX_MODULE_PASSPCI:
|
||||
if (passpci) {
|
||||
printf("Error: Only one Passthrough Mini-PCIe module is supported!\n");
|
||||
} else if (i != 0) {
|
||||
printf("Error: Passthrough Mini-PCIe module should be the first connected module!\n");
|
||||
} else {
|
||||
++passpci;
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
/* now configure modules */
|
||||
|
||||
if (get_reset_gpio(&reset_gpio) < 0)
|
||||
return 0;
|
||||
|
||||
if (peridot > 0) {
|
||||
if (configure_peridots(&reset_gpio) < 0) {
|
||||
printf("Cannot configure Peridot modules!\n");
|
||||
peridot = 0;
|
||||
}
|
||||
} else {
|
||||
dm_gpio_set_value(&reset_gpio, 1);
|
||||
mdelay(50);
|
||||
dm_gpio_set_value(&reset_gpio, 0);
|
||||
mdelay(50);
|
||||
}
|
||||
|
||||
if (peridot || topaz) {
|
||||
/*
|
||||
* now check if the addresses are set by reading Scratch & Misc
|
||||
* register 0x70 of Peridot (and potentially Topaz) modules
|
||||
*/
|
||||
|
||||
bus = miiphy_get_dev_by_name("neta@30000");
|
||||
if (!bus) {
|
||||
printf("Cannot get MDIO bus device!\n");
|
||||
} else {
|
||||
for (i = 0; i < peridot; ++i)
|
||||
check_switch_address(bus, 0x10 + i);
|
||||
|
||||
if (topaz)
|
||||
check_switch_address(bus, 0x2);
|
||||
|
||||
sw_blink_leds(bus, peridot, topaz);
|
||||
}
|
||||
}
|
||||
|
||||
printf("\n");
|
||||
|
||||
return 0;
|
||||
|
|
|
|||
Loading…
Reference in New Issue
Block a user