The Amlogic AXG MIPI + PCIe Analog PHY provides function for both PCIe and
MIPI DSI at the same time, and provides the Analog part of MIPI DSI transmission
and Analog part of the PCIe lines.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Amlogic AXG SoCs embeds a MIPI D-PHY used to communicate with DSI
panels.
This D-PHY depends on a separate analog PHY.
Signed-off-by:Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the PHY configure op callback to the generic PHY uclass to permit
configuring the PHY.
It's useful for MIPI DSI PHYs to setup the link timings.
Signed-off-by:Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The MIPI D-PHY spec defines default values and boundaries for most of the
parameters it defines. Introduce helpers to help drivers get meaningful
values based on their current parameters, and validate the boundaries of
these parameters if needed.
These helpers and header are taken from Linux commit 9123e3a74ec7 ("Linux 5.9-rc1").
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support of missing I2C6_K with bit 3 of RCC_MC_APB5ENSETR =
I2C6EN: I2C6 peripheral clocks enable.
This patch allows customer to use I2C6 in SPL or in U-Boot
as other I2C instance, already support in clk driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Bind only the enabled GPIO subnode, to avoid to probe the node
"gpio-controller" present in SOC dtsi (disabled by default) but
not enabled in the included pincontrol dtsi file.
For example, in stm32mp15xxac-pinctrl.dtsi 2 gpio bank are absent:
gpioj: gpio@5000b000
gpiok: gpio@5000c000
Then these GPIO are absent in output of command "dm tree" and
"gpio status -a"
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
OTYPE can be used for output or for alternate function to select
PP = push-pull or OP = open-drain mode, according reference manual
(Table 81. Port bit configuration table).
This patch removes this indication for input pins and adds it
for AF and output pins for pinmux command output.
Fixes: b305dbc08b ("pinctrl: stm32: display bias information for all pins")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Instead of redefining a pin's name size, use PINNAME_SIZE defined
in include/dm/pinctrl.h
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
pin-controller pin's name must be equal to pin's name used in device
tree with "pins" DT property.
Issue detected on stm32mp157c-ev1 board with goodix touchscreen.
In DT, the goodix's pin is declared in DT with the node:
goodix_pins: goodix {
pins = "gpio14";
bias-pull-down;
};
Whereas in stmfx pin-controller driver, pin's name are equal to
"stmfx_gpioxx" where xx is the pin number.
This lead to not configure stmfx's pins at probe because pins is
identified by its name (see pinctrl_pin_name_to_selector() in
pinctrl-generic.c) and stmfx pin "gpio14" can't be found.
To fix this issue, come back to the original stmfx pin's name.
Revert "pinctrl: stmfx: update pin name"
This reverts commit 38d30cdcd65c73eeefac5efa328ad444a53b77dd.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
- Espressobin: Set default env values at runtime (Pali)
- Espressobin: Set the maximum slave SPI speed to 40MHz (Pali)
- theadorable: PCIe test code enhancement and early deemphasis
enabling (Stefan)
- pci_mvebu: Disable config access to PCI host bridge ports (Stefan)
- mv_sdhci: parse device-tree entry (Baruch)
Update gpio driver to use same logic for big-endian and little-endian
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
LX2162A is not like LX2160A which has different PCIe controller
in rev1 and rev2 silicon. It supports only one configuration of
PCIe controller, which is same as LS2088A. So update PCIe
compatible string same as LS2088A.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Tested-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch moves the SVR definitions to a new svr.h for
Layerscape armv7 and armv8 platforms respectively, so that
the PCIe driver can reuse them.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The LS1088 requires the same QUADSPI_QURIK_BASE_INTERNAL
workaround as the LS208x and also has a 64 byte TX buffer.
With the previous settings SPI-NAND reads over AHB were
corrupted.
Fixes: 91afd36f38 ("spi: Transform the FSL QuadSPI driver to use the SPI MEM API")
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Adapted from kernel commit b0177aca7aea
From: Michael Walle <michael@walle.cc>
Make use of a core helper to ensure the desired width is respected
when calling spi-mem operators.
Otherwise only the SPI controller will be matched with the flash chip,
which might lead to wrong widths. Also consider the width specified by
the user in the device tree.
Fixes: 91afd36f38 ("spi: Add a driver for the Freescale/NXP QuadSPI controller")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200114154613.8195-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mathew McBride <matt@traverse.com.au> [adapt for U-Boot]
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Current MDIO wait time is too long, which introduce long delay when
PHY negotiation register checking. Reduce it to 10us
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fugang Duan <Fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
We have encountered circumstances when a board design does not include
pull-up resistors on the external MDIO buses which are not used. This
leads to the MDIO data line not being pulled-up, thus the MDIO controller
will always see the line as busy.
Without a timeout in the MDIO bus driver, the execution is stuck in an
infinite loop when any access is initiated on that external bus.
Add a timeout in the driver so that we are protected in this
circumstance. This is similar to what is being done in the Linux
xgmac_mdio driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Provide an explicit configuration option to disable default "unlock all"
of any flash chip which supports locking. It doesn't make sense to
automatically unprotect the entire flash on each u-boot startup if the
block protection bits are actually used.
Traditionally, the unlock was there to be able to write to flash devices
which powered-up with the block protection bits set. Over time this
feature creeped into all flash devices which support locking.
For a more detailed description and discussion see:
https://lore.kernel.org/linux-mtd/20201203162959.29589-8-michael@walle.cc/
Keep things simple in u-boot and just provide a configration option to
disable this behavior which can be set per board.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Call mmc_of_parse() so that generic DT properties like 'non-removable'
are taken into account.
This fixes boot on Clearfog with eMMC on SOM that requires the
non-removable property.
Reported-by: Thorsten Spille <thorsten_spille@netcor.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
This patch changes the PCI config routines in the Armada XP / 38x driver
to not allow access to the PCIe root ports.
While updating the Armada XP based theadorable to the latest mainline
and testing it with the DM PCI driver I noticed, that the PCI root
bridge was being configured incorrectly. Resulting in the PCIe Intel
WiFi was not working correctly in Linux. With this patch applied, all
PCIe devices work without any issues in Linux again.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
In case MMC has MBR system and fastboot writes GPT,
MMC is still recognized as MBR.
Invoke part_init() to purge cached data and update
information about partition table type.
Signed-off-by: Roman Stratiienko <r.stratiienko@gmail.com>
Add command oem bootbus which executes the command
``mmc bootbus <id> <arg>`` on the current fastboot mmc device
(<i> = CONFIG_FASTBOOT_FLASH_MMC_DEV) to set the eMMC boot
configuration on first update, with
<arg> = boot_bus_width reset_boot_bus_width boot_mode
$> fastboot oem bootbus:<boot_bus_width> <reset_boot_bus_width> <boot_mode>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add fastboot command oem partconf which executes the command
``mmc partconf <id> <arg> 0`` on the current <id> mmc device
to configure the eMMC boot partition with
<arg>: boot_ack boot_partition, so the command is:
$> fastboot oem partconf:<boot_ack> <boot_partition>
The partition_access argument is forced to 0 (userdata)
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
[lukma - Kconfig adjustments after merging this patch]
Update the code and the configs for eMMC boot and userdata
partitions acces
- FASTBOOT_MMC_BOOT_SUPPORT: boot partition 1 and 2 (erase/write)
- FASTBOOT_MMC_BOOT1_NAME: boot partition 1, default name="mmc0boot0"
- FASTBOOT_MMC_BOOT2_NAME: boot partition 2, default name="mmc0boot1"
This patch also removes the unnecessary dependency with
ARCH_MEDIATEK and EFI_PARTITION.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Split userdata and boot partition support for eMMC update
and correct the description (update is supported).
The new configuration CONFIG_FASTBOOT_MMC_USER_SUPPORT
allows to activate support of userdata partition update,
based on target name=CONFIG_FASTBOOT_MMC_USER_NAME
This patch also removes the unnecessary dependency with
ARCH_MEDIATEK and EFI_PARTITION.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
It is possible to implement fastboot_set_reboot_flag in a generic way
if BCB commands are turned on for a target. Using
bcb_set_reboot_reason allows to do this by simply passing string with
correct reboot reason that should be handled during next boot process.
If BCB are turned off, then bcb_set_reboot_reason would simply return
error, so it won't introduce any new behaviour for such targets.
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
This reverts commit 0ebf9842e5.
Current generic implementation of fastboot_set_reboot_flag is somewhat
messy and requires some additional configuration option to be enabled
besides CMD_BCB, so it reverts that implementtion in order to bring a
new cleaner one.
Next commit introduces new generic implementation of
fastboot_set_reboot_flag.
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
- Sync DTS from Linux kernel for all K3 platforms
- Add MMC higher speed nodes for AM65x, J721e, J7200
- Convert Nokia RX-51 to use CONFIG_DM_MMC
- Minor fixes for LEGO MINDSTORMS
Use the generic sdhci_set_control_reg() instead of duplicating
in platform driver.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
According to the AM654x Data Manual[1], the setup timing in lower speed
modes can only be met if the controller uses a falling edge data launch.
To ensure this, the HIGH_SPEED_ENA (HOST_CONTROL[2]) bit should be
cleared in default speed, SD high speed, MMC high speed, SDR12 and SDR25
speed modes.
Use the sdhci writeb callback to implement this condition.
[1] http://www.ti.com/lit/gpn/am6546 Section 5.10.5.16.1
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
With the new SW tuning App note[1], a custom tuning algorithm is
required for eMMC HS200, HS400 and SD card UHS modes. The algorithm
involves running through the 32 possible input tap delay values and
sending the appropriate tuning command (CMD19/21) for each of them
to get a fail or pass result for each of the values. Typically, the
range will have a small contiguous failing window. Considering the
tuning range as a circular buffer, the algorithm then sets a final
tuned value directly opposite to the failing window.
[1] https://www.ti.com/lit/pdf/spract9
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add support for writing new clock buffer select property for both
the am654x and j721e 4 bit IPs
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
DLL need only be enabled for speed modes and clock frequencies at or
above 50 MHz. For speed modes that don't enable the DLL, we need to
configure a static input delay value. This involves reading an optional
itap-del-sel-* value from the device tree and configuring it for the
appropriate speed mode.
Therefore, move all dll configurations to their own functions and gate it
with 50 MHz speed and a minimum mode. If both these conditions are not
satisfied then configure delay chain modes.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add Support for AM65x PG2.0. Use the SoC bus framework to fixup
the platform data and do DLL calibration if the revision is 1.0
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Not all controllers need calibration for the PHY DLL. Add a DLL_CALIB
flag to indicate the same.
Also move the write of trm_icp and driver strength to the set_clock()
function to match the kernel configuration flow.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Convert the flags field defines to use the BIT() macro.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
There are some speed modes that work without switching the dll on.
Unconditionally switch off the DLL before setting clock frequency to
support this case. The software will automatically enable DLL for speed
modes that require it. This also means the dll_on priv data member is no
longer required.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add a set_voltage() function which handles the switch from 3.3V to 1.8V
for SD card UHS modes.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The K3 R5F remoteproc driver in U-Boot was upstreamed prior to the
equivalent remoteproc driver in the Linux kernel. Some of the DT
properties used in U-Boot got upstreamed using different names
in Linux kernel.
The modified property names include the R5F cluster mode configuration
property "lockstep-mode"; and three different individual R5F core config
properties - "atcm-enable", "btcm-enable" and "loczrama". The property
names were updated as follows:
lockstep-mode => ti,cluster-mode
atcm-enable => ti,atcm-enable
btcm-enable => ti,btcm-enable
loczrama => ti,loczrama
Update the K3 R5F remoteproc driver, the corresponding binding, and
all the existing usage in AM65x, J721E and J7200 dts files all at
once to use the new properties and to not break any bisectability.
Signed-off-by: Suman Anna <s-anna@ti.com>
The dm_spi_ops.xfer() API does not support dual and quad SPI modes. It
also doesn't allow the zynqmp_gqspi driver to calculate the correct
number of dummy cycles for some NOR ops (as doing so also requires the
buswidth).
Port the zynqmp_gqspi driver to spi_controller_mem_ops, which gives us
the buswidth values to correctly support all SNOR_PROTO_X_X_X commands
and to properly calculate dummy cycles.
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
CC: jagan@amarulasolutions.com
CC: michal.simek@xilinx.com
CC: Ashok Reddy Soma <ashokred@xilinx.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
sandbox_scmi_devices_ctx() may return NULL. We should not dereference this
value in sandbox_scmi_devices_remove().
The problem was indicated by 'gcc-11 -fanalyzer'.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
priv->iobase was declared as phys_addr_t which is now a 64-bit
address. In a 32-bit build, this causes the following warning
seen when building ftmac100.c:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Cast priv->iobase with uintptr_t.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
dev_read_addr() returns fdt_addr_t which is now a 64-bit address.
In a 32-bit build, this causes the following warning seen when
building serial_sifive.c:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Cast the return value with uintptr_t.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Add another flag to the DM core which could be assigned to drivers and
which makes those drivers call their remove callbacks last, just before
booting OS and after all the other drivers finished with their remove
callbacks. This is necessary for things like clock drivers, where the
other drivers might depend on the clock driver in their remove callbacks.
Prime example is the mmc subsystem, which can reconfigure a card from HS
mode to slower modes in the remove callback and for that it needs to
reconfigure the controller clock.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present if device_remove() decides that the device should not actually
be removed, it still calls the uclass pre_remove() method and powers the
device down.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the uclass pre-remove method is called before the children are
removed. But the children may refused to be removed, in whch case the
uclass is in a tricky situation. At present we handle this by calling
the uclass' post_probe() method. But it seems better to avoid doing
anything with the uclass in this case.
Switch the ordering so that we make sure the children can be removed
before advising the uclass.
Signed-off-by: Simon Glass <sjg@chromium.org>
This flag has the word 'REMOVE' in it which means it conflicts with
the DM_REMOVE flags. Rename it to DM_FLAG_LEAVE_PD_ON which seems to
indicate its purpose well enough.
Signed-off-by: Simon Glass <sjg@chromium.org>
This has no useful meaning in U-Boot and will never be returned. We want
to reserve this flag for internal driver model use.
Drop the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
This has no useful meaning in U-Boot. Use -ENOMEM since that appears to
be what has gone wrong in this case. We want to reserve this flag for
internal driver model use.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
- Fix CMD_ACPI dependency in Kconfig
- Correct overflow in __udelay() in TSC timer driver
- Add a devicetree node for eMMC for Coral
- Minor improvements on image loading
- Reduce size of Samus image
At present long delays such as msleep(2000) can cause an overflow in this
function. There is no need for this, since it already uses a 64-bit int.
Add a cast to correct this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useless and misleading to print the ret variable that is not set
by the dev_read_addr routine. Also, move the '\n' character after the
round bracket that contains the error code.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The pinmux choice for the RMII/RGMII pins the EMAC is connected to is
not dependent on the EMAC IP, but on the SoC it is integrated in.
Deriving the pinmux from the DT compatible string (as we do at the
moment) will thus cause problems with certain EMAC IP / SoC combinations.
To avoid this exact issue with the H616, let's use our Kconfig MACH
symbols to choose the correct pinmux setup.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
At the moment we only consider the EPHY register for those SoCs were
we actually have an internal PHY to configure. However even other SoCs
have this register, an expect the EPHY select bit to be cleared for
proper operation with an external PHY.
Rework sun8i_emac_set_syscon_ephy() to be called regardless of the EMAC
model, and clear the H3_EPHY_SELECT bit if no internal PHY is used.
We get away without it so far because SoCs like the A64 clear this bit
on reset, but we need to explicitly clear it on the H616, for instance.
The Linux driver does so as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
As we need standard usb_ep's desc, so set it when enable ep.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Change to use wMaxPacketSize of current speed EP desc for request
length wrap up.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Remove the gadget driver speed check, and set its max_speed to
be USB_SPEED_HIGH.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
If one of functions is not super speed capable, we need force the udc
to be high speed, this is an equivalent implementation of
usb_gadget_udc_set_speed() in kernel but simple, which set the gadget
max_speed to be high speed, so afterwards when start gadget duc can
set the HW to be USB 2.0 mode.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set its max_speed to be super speed.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add super speed EP config.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch is to add usb gadget super speed support in common
driver, including BOS descriptor and select the super speed
descriptor from function driver.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Always use the new added config for os_desc_config to fix cdev->
os_desc_config may miss set in case we restart usb gadget driver.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The current way to set cdev->os_desc_config is wrong if user restart
fastboot, as the old config is not used anymore and new allocated
usb_configuration will be used, so set the os_desc_config while
usb_add_config.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add device interface GUID for Microsoft Extended Properties Feature
Descriptor.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This is a proting patch from linux kernel: 37a3a533429e
("usb: gadget: OS Feature Descriptors support"), the original commit
log see below:
There is a custom (non-USB IF) extension to the USB standard:
http://msdn.microsoft.com/library/windows/hardware/gg463182
They grant permission to use the specification - there is
"Microsoft OS Descriptor Specification License Agreement"
under the link mentioned above, and its Section 2 "Grant
of License", letter (b) reads:
"Patent license. Microsoft hereby grants to You a nonexclusive,
royalty-free, nontransferable, worldwide license under Microsoft鈥檚
patents embodied solely within the Specification and that are owned
or licensable by Microsoft to make, use, import, offer to sell,
sell and distribute directly or indirectly to Your Licensees Your
Implementation. You may sublicense this patent license to Your
Licensees under the same terms and conditions."
The said extension is maintained by Microsoft for Microsoft.
Yet it is fairly common for various devices to use it, and a
popular proprietary operating system expects devices to provide
"OS descriptors", so Linux-based USB gadgets whishing to be able
to talk to a variety of operating systems should be able to provide
the "OS descriptors".
This patch adds optional support for gadgets whishing to expose
the so called "OS Feature Descriptors", that is "Extended Compatibility ID"
and "Extended Properties".
Hosts which do request "OS descriptors" from gadgets do so during
the enumeration phase and before the configuration is set with
SET_CONFIGURATION. What is more, those hosts never ask for configurations
at indices other than 0. Therefore, gadgets whishing to provide
"OS descriptors" must designate one configuration to be used with
this kind of hosts - this is what os_desc_config is added for in
struct usb_composite_dev. There is an additional advantage to it:
if a gadget provides "OS descriptors" and designates one configuration
to be used with such non-USB-compliant hosts it can invoke
"usb_add_config" in any order because the designated configuration
will be reported to be at index 0 anyway.
This patch also adds handling vendor-specific requests addressed
at device or interface and related to handling "OS descriptors"."
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
As other users may use utf8_to_utf16le() to convert the utf8
to utf16 for usb, so move it to head file.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This is a porting patch from linux kernel: 19824d5eeece
("usb: gadget: OS String support"), original commit log
see below:
"There is a custom (non-USB IF) extension to the USB standard:
http://msdn.microsoft.com/library/windows/hardware/gg463182
They grant permission to use the specification - there is
"Microsoft OS Descriptor Specification License Agreement"
under the link mentioned above, and its Section 2 "Grant
of License", letter (b) reads:
"Patent license. Microsoft hereby grants to You a nonexclusive,
royalty-free, nontransferable, worldwide license under Microsoft鈥檚
patents embodied solely within the Specification and that are owned
or licensable by Microsoft to make, use, import, offer to sell,
sell and distribute directly or indirectly to Your Licensees Your
Implementation. You may sublicense this patent license to Your
Licensees under the same terms and conditions."
The said extension is maintained by Microsoft for Microsoft.
Yet it is fairly common for various devices to use it, and a
popular proprietary operating system expects devices to provide
"OS descriptors", so Linux-based USB gadgets whishing to be able
to talk to a variety of operating systems should be able to provide
the "OS descriptors".
This patch adds optional support for gadgets whishing to expose
the so called "OS String" under index 0xEE of language 0.
The contents of the string is generated based on the qw_sign
array and b_vendor_code.
Interested gadgets need to set the cdev->use_os_string flag,
fill cdev->qw_sign with appropriate values and fill cdev->b_vendor_code
with a value of their choice.
This patch does not however implement responding to any vendor-specific
USB requests."
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
As the SDP protocol use the predefined ep num for communication, we can't
change its name hence reset its ep num while do ep autoconfig, this is
only apply for SPL.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since some new fields in usb_ep structure been moved to usb_ss_ep.
The CDNS3 gadget driver should replies on this operation to bind the
usb_ss_ep with the endpoint descriptor when function layer uses
usb_ep_autoconfig to add endpoint descriptors to gadget. So that
CDNS3 driver can know the EP information and configure the EP once
the set configuration request is received.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Each array is used only in one file (core.c or ep0.c). Move their content
to correct file, mark them as static and do not export out of current file.
This change allows to decrease size of u-boot.bin as more of those strings
are not used.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reinitialize dfu_env_entities after flashing the 'SCRIPT' entity to
ensure that the potential changes to the 'dfu_alt_info' environment
variable are applied.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Define a new 'SCRIPT' type for DFU entities. The downloaded data are
treated as simple u-boot's scripts and executed with run_command_list()
function.
Flashing the 'SCRIPT' entity might result in changing the 'dfu_alt_info'
environment variable from the flashed script, so add a global variable
for tracking the potential need to reinitialize the dfu_alt_info related
structures.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Define a new 'SKIP' type for the DFU entities. The flashed data for that
entity is simply ignored without returning any error values.
This allows to have one flashing procedure and images for the different
board types or variants, where each board uses only the images relevant
to it and skips the rest. This is especially usefull for the THOR
protocol, which usually transfers more than one file in a single session.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
[mszyprow: rephrased commit message and docs for easier reading, changed
subject to "dfu: add 'SKIP' entity"]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Use the default MMC device set in the command line if entity specifies it
as -1. This allows to use the same dfu_alt_info string for different MMC
devices (like embedded eMMC and external SD card if data layout is the
same on both devices).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
In case of usb_add_function() failure the error path has an issue,
i.e the global pointer variable is assigned to garbage
Fix the above mentioned issue by assigning pointer to NULL.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
In case of usb_add_function() failure the error path has two issues:
- the potentially allocated structure isn't getting freed
- the global pointer variable is assigned to garbage
Fix the above mentioned issues by freeing memory and assigning NULL.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Casting 32bit int value directly into 64bit unsigned type causes
wrong value for file size equal or larger than 2GB. Fix the wrong
file size by casting uint32_t first.
Fixes: commit 1fe9ae76b1 ("gadget: f_thor: update to support more than 4GB file as thor 5.0")
Reported-by: Junghoon Kim <jhoon20.kim@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
For UBI partitions ("partubi" in dfu_alt_info), dfu_fill_entity_mtd sets
the mtd.ubi flag; however other functions incorrectly check for nand.ubi
instead. Fix this by checking for the correct flag.
Signed-off-by: Guillermo Rodriguez <guille.rodriguez@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The R-Car3 SDHI should set these two bits in DMA_MODE register according
to the specification, to indicate 64bit bus width. No other bus width
options are permitted and the default value is 0, which is incorrect.
Set the bits accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Provide information about host backed block device.
Mark the device created by 'host bind' as removable.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The UEFI Self Certification Test (SCT) checks the SetTime() service with
the following steps:
* set date
* reset
* check date matches
To be compliant the sandbox should keep the offset to the host RTC during
resets. The implementation uses the environment variable
UBOOT_SB_TIME_OFFSET to persist the offset.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present this function uses the old format for reading hashes. Add
support for the current format.
Add a test while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
The use of pinctrl in the core of driver model is useful but can provoke
some strange behaviour. Add a comment to aid debugging.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current driver name does not match its compatible string, so
of-platdata does not work correctly. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
These cannot work with of-platdata since they currently need the
devicetree at runtime. Disable the emulators and the sandbox I2C driver
that needs them. We can enable these later, if needed for testing.
Switch the of_plat_parent test over to use a simple bus instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
The EC can store small amounts of data for the benefit of the
verified boot process. Since the EC is seldom reset, this can allow the
AP to store data that survives a reboot or a suspend/resume cycle.
Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
On x86 platforms the EC provides a way to read 'switches', which are
on/off values determined by the EC.
Add a new driver method for this and implement it for LPC.
Signed-off-by: Simon Glass <sjg@chromium.org>
This should not happen in normal operation, but the EC might have a bug,
so add a run-time check just in case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow a longer time for the EC to reboot. Also use a constant for the
hash delay time, so it is clear what it is for.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is used several times in this file. Put it in a function to avoid
code duplication.
Also add a test for this function. There are no cros_ec tests at present,
so it is time to update the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update the TPM description to include the interrupt mechanicm since this
is useful to know. Also add a warning if the TPM cannot be found and a
debug line if it succeeds.
Signed-off-by: Simon Glass <sjg@chromium.org>
When the Cr50 starts up it doesn't have a valid locality. The driver sets
it to -1 to indicate that. Tracking this allows cr50_i2c_cleanup() to
avoid releasing a locality that was not claimed.
However the helper functions that generate the flags use a u8 type which
cannot support -1, so they return a locality of 0xff.
Fix this by updating the type. With this, 'tpm startup TPM2_SU_CLEAR'
works as expected.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch adds support for MTK SPI NOR controller, which you
can see on mt7622 & mt7629.
1. This controller is designed only for SPI NOR. We can't adjust
its bus clock dynamically. Set clock in dts instead.
2. This controller only supports 1-1-1 write mode.
3. Remove mtk_snor_match_read() since upper SPI-MEM layer already
handles command.
4. sf read/write/update commands are tested with this driver.
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
This is a basic driver for the ultra-low-power Abracon AB x80x series
of RTC chips. It supports in particular, the supersets AB0805 and AB1805.
It allows reading and writing the time, and enables the supercapacitor or
battery charger.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Set this flag so that it is available to those looking at the device. For
non-removable devices there is no need to check for insertion/removable
since the media can never change.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
At present if an eMMC part is in the system, the ACPI table generated
will include information about that, as well as the SD card. We only need
to include the SD card, since it has a card-detect GPIO. Use a different
compatible string for each option, and add code only for the SD card.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
In some cases so much of the framebuffer is updated that it is not worth
copying the changes piece by piece to the copy framebuffer. Add a function
to copy the whole thing.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch completely removes CONFIG_PCI_ENUM_ONLY from the PCI code as
it is not configured for any board (any more). With this removal, some
PCI related files get cleaned up a bit.
Additional, dm_pciauto_setup_device() is now static, as it's not
referenced from any code outside of this C file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit add an option TPL_BOOTCOUNT_LIMIT to
use bootcount on TPL.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Espressobin: Disable slot when emmc is not present (Pali)
- DS414; config header cleanup (Phil)
- PCI: auto-config enhancement (Phil)
- pci_mvebu: Also map IO region (Phil)
- serial: a3720: Implement pending method for output direction (Pali)
- turris_mox: Enable a few commands (Marek)
- helios4 & ClearFog changes (Dennis)
- Plus some minor misc changes
The phydev structure has a PHY OF node pointer in it, use that OF node
first when looking up PHY OF node properties, since that is likely the
correct PHY OF node pointer. If the pointer is not valid, which is the
case e.g. on legacy DTs, fall back to parsing MAC ethernet-phy subnode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Add phy driver support for MACs embedded inside Cortina Access SoCs
Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Tom Rini <trini@konsulko.com>
CC: Aaron Tseng <aaron.tseng@cortina-access.com>
Moved out PHY specific code out of Cortina NI Ethernet driver
and into a Cortina Access PHY interface driver
Add some missing address translations from virtual address in local DRAM
to physical address, which is needed for the DMA transactions to work
correctly.
This issue was detected while testing the e1000 driver on the MIPS
Octeon III platform, which needs address translation.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Using (dm_)pci_virt_to_mem() is incorrect to translate the virtual
address in local DRAM to a physical address. The correct macro here
is virt_to_phys() so switch to using this macro.
As virt_to_bus() is now not used any more, this patch also removes
both definitions (DM and non-DM).
This issue was detected while testing the e1000 driver on the MIPS
Octeon III platform, which needs address translation.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
bus_to_phys() is defined but not referenced at all. This patch removes
it completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Value pcie->dev in function pcie_advk_probe() is not initialized yet
so use dev as argument for dev_dbg()/dev_warn().
Function pcie_advk_wait_pio() itself prints error message on failure
so do not print duplicate error message in caller.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
To check if some output characters are waiting either in Transmitter
Holding Register or Transmitter Shift Register we need to look at
TX_EMPTY bit of UART Status Register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Configure an IO region and window for PNP identical to how MEM region is
set up. Linux does this only if the DT defines a pcie-io-aperture
property for the SOC, but since all supported boards do this should not
be needed.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
On my DS414, some PCI devices return odd values when probing BAR sizes.
An obvious case is all-ones response, the Linux driver
(drivers/pci/probe.c) catches those explicitly and a comment explains
that either bit 0 or bit 1 must be clear (depending on MEM or IO type).
Other BARs return e.g. 0xfff0000f or 0xfff00004 and thus manage to break
size calculation due to the "middle" zeroes. Mitigate that copying more
or less what Linux does and do a "find least bit set".
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change extends previous commit 061c6d1b23 ("arm: mvebu: Espressobin:
Detect presence of emmc at runtime") and when emmc is not present then emmc
is removed from U-Boot DM and corresponding slot is disabled. Therefore on
Espressobin board without soldered emmc, state of emmc hw should be same as
if emmc was disabled in DTS.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The Armada driver also works on Nedap's custom Kirkwood board with a
Marvell 88F6180 CPU. The original commit of that driver,
commit 704d9a645e ("gpio: Add DM GPIO driver for Marvell MVEBU"),
also mentions that this driver would be suitable for Kirkwood. This
does not completely replace the Kirkwood specific driver as there
are still boards depending on that driver.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
CC: Stefan Roese <sr@denx.de>,
Reviewed-by: Stefan Roese <sr@denx.de>
H616 pinctrl is no different configuration wise than others, so just add
compatible for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
H616 is very similar to H6 so most of the infrastructure can be reused.
However, two big differences are that it doesn't have functional SRAM A2
which is usually used for TF-A and it doesn't have ARISC co-processor.
It also needs bigger SPL size - 48 KiB.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far the only difference between the various Allwinner MMC controller
we are concerned about is the mod clock register offset.
This is actually not directly related to the MMC controller IP, but an
integration choice, dependent on the SoC this appears in.
To avoid becoming trapped with some compatible fallback strings, let's
remove the whole struct sunxi_mmc_variant, and replace this with a SoC
based choice, which we can derive from the CONFIG_MACH_SUNx_y symbols.
This will later simplify H616 support.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
While currently none of the newer Allwinner SoCs currently has I2C
support implemented in U-Boot, this will change soon. mvtwsi driver is
good as it is for them except one macro. Update it to be ready once I2C
support lands for those SoCs.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
It turns out that several SoCs share same mmc configuration as H6. In
order to lower ifdef clutter replace H6 specific macro with common one.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This PMIC can be found on H616 boards and it's very similar to AXP805
and AXP806.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far all GBit users of the sun8i-emac driver were using the "rgmii"
PHY mode, even though this turns out to be wrong. It just worked because
the PHY driver doesn't do the proper setup (yet).
In fact for most boards the "rgmii-id" or "rgmii-txid" PHY modes are the
correct ones.
To allow the DTs to describe the phy-mode correctly, and to stay
compatible with Linux, at least allow those other RGMII modes in the
driver.
This avoids breakage if mainline DTs will be synced with U-Boot.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmAOkP8cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKedCACiDHgP71VKSOiYnEU4
vHD/ANmfMXqnsL71PpSdagnBRAl4vpm46CnD+Mq7RtchxGDNufX6tWJSI04Ci0bC
mfmIfVEjePOnuUayylJ55OlrtJVpBqJFPqxM6MFcIF7nRja1r5thV1jTLNu+b4sm
gg2sk1mC/531Lxbk8S7x+diPymNRArEm3IEw+xEqUhsNVQCKjOEcxi/BWIB2prR3
NxRSGdW3j4CKdBqt7uOL1bqApeQQ9m0/gm1tE3hMXUo09I7uXmb7U52aKb5cV8L+
8ZOlbav6yaPACe3p9npp4K0ByXMmYHjeo1NZW4cvAoKfzragdu0Cv7f0ssVCgrlR
p1e3
=xS6A
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.04 cycle
This feature set includes macb updates for all interfaces and new
sama7g5 variant support; micrel ksz9031 DLL support; a new board from
Giant based on Adafruit feather form factor which contains a SAMA5D27
SoC; several fixes regarding the NAND flash PMECC block; and pincontrol
drive strength support for pio4 controller.
Add DM_FLAG_PRE_RELOC flag for reset-mtmips to make sure this driver can
be probed before relocation even if u-boot,dm-pre-reloc is not present
in the dts.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Currently this driver does not set the value of plat->cfg.f_max, which
results in that MMC framework will always run at the lowest frequency.
This patch sets plat->cfg.f_max to the maximum allowed frequency, which
equals to the source clock frequency.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The driver is missing pad control settings (pad delay and pad conf) for
the mt7620 and mt76x8. Although mt76x8 still works well, mt7620 will
encounter CRC error on data transfers.
This patch adds default pad control settings for mt7620_compat.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
It turns out that the sclk cycles used by mt7620/mt7628 is the same as
other chips (20 bits, 1048576), not 65536.
This patch removes sclk_cycle_shift from dev_comp, and uses a macro with
a value 20 instead.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds ethernet driver for MediaTek MT7620 SoC.
The MT7620 SoC has a built-in ethernet (Frame Engine) and a built-in
7-port switch and two xMII interfaces (can be MII/RMII/RGMII).
The port 0-3 of the switch connects to intergrited FE PHYs. Port 4 can be
configured to connect to either the intergrited FE PHY, or the xMII.
Port 5 always connects to the xMII. Port 6 is the CPU port.
This driver supports MT7530 giga switch connects to port 5.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds spi controller support for MediaTek MT7620 SoC.
The SPI controller supports two chip selects. These two chip selects are
implemented as two separate register groups, but they share the same bus
(DI/DO/CLK), only CS pins are dedicated for each register group.
Appearently these two register groups cannot operates simulataneously so
they are implemented as one controller.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds watchdog support for the Mediatek MT7620 SoC
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds pinctrl support for MediaTek MT7620 SoC.
The MT7620 SoC supports only pinmux.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds a clock driver for MediaTek MT7620 SoC.
This driver provides clock gate control as well as getting clock frequency
for CPU/SYS/XTAL and some peripherals.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds uart support for MediaTek MT7620 and earlier SoCs.
The UART used by MT7620 is incompatible with the ns16550a driver.
All registers of this UART have different addresses. A special 16-bit
register for Divisor Latch is used to set the baudrate instead of the
original two 8-bit registers (DLL and DLM).
The driver supports of-platdata which is useful for tiny SPL.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
In case the clock framework is enabled, enable the SPI controller clock
and obtain max frequency from the clock framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
The CSPI/ECSPI register bits do not differ between newer SoCs, instead
of having multiple copies of the same thing for each iMX SoC, define
the bits in the driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
Add ECSPI clock entries to iMX8MN clock driver. Only make those entries
available in case SPI support in U-Boot is enabled at all to conserve
space, esp. in SPL.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Now that header files no longer include common.h it must be included
first.
Otherwise the build fails with errors like
include/asm/arch/clock.h:43:1: error: unknown type name 'u32'
u32 imx_get_uartclk(void);
Fixes: c3dc39a2f8 ("arm: Don't include common.h in header files")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Simon Glass <sjg@chromium.org>
When doing DDR scrub, the DDR may enter into self refresh if the
selfref_en is enabled before DDR scrub. This will cause scrub
can't complete that SBRSTAT.scrub_done won't be set.
Since the selfref_en can be programmed during the course of
normal operation, move it after DDR scrub
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Take into account all RGMII interface types. Depending on it
the RGMII PHY's timings are setup.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
clk_set_rate() returns the set rate in case of success and a
negative number in case of failure. Consider failure only the
negative numbers.
Fixes: 3ef64444de ("dm: net: macb: Implement link speed change callback")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Different implementation of USER IO register needs different
mapping for bit fields of this register. Add implementation
for this and, since clken is part of USER IO and it needs to
be activated based on per SoC capabilities, add caps in
macb_config where clken specific information needs to be filled.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Use dev_read_prop instead of using the fdt_read_property which
reads from the GD struct's fdt.
This way the node is accessed via the device config instead of the
global struct, which makes code more portable and GD independent.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add Rockchip dwc based PCIe controller driver for rk356x platform.
Driver support Gen3 by operating as a Root complex.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Add the Rockchip Synopsys based PCIe 3.0 PHY driver as
part of Generic PHY framework.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
There is no need to define the same macros in drivers.
All macros have been added by commit 17a42abb40 ("mmc: Define timing
macro's").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The DWMAC4 IP has the possibility to skip up to 7 AXI bus width size words
after the descriptor. Use this to pad the descriptors to cacheline size and
remove the need for noncached memory altogether. Moreover, this lets Tegra
use the generic cache flush / invalidate operations.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
A sporadic condition occurs when the "bad packet" error is triggered
repeatedly, which results in "bad packet" messages scrolling on the
console during transfer. To avoid triggering this, reset the internal
RXFC count on the first occurance of the "bad packet", which forces
the code to re-read the RX packet count from the MAC, and prevents
any additional "bad packet" messages if there are no more packets in
the MAC. Also print better debug information if this condition occurs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Tom Rini <trini@konsulko.com>
Implement programming MAC address to the hardware also for device model
configuration.
Fixes: b565b18a29 ("board: ge: bx50v3: Enable DM for PCI and ethernet")
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The timer being used by this driver may have already been used by first
stage bootloader (e.g. ATF/preloader), and it's settings may differ from
what this driver is going to use.
This may cause issues, such as inaccurate timer frequency due to
incorrect clock divider.
This patch adds the initialization code to avoid them.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
If no GPIO controller is found, the return value should not depend on a
random value on the stack. Initialize variable ret.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
drivers/mtd/mw_eeprom.c contains code that never worked. mw_eeprom_write()
and mw_eeprom_read() have incorrect loop conditions:
while (len <= 2) {
CONFIG_MW_EEPROM is not set anywhere. So let's simply drop the module.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Avoid calling free(addr) twice if the device for ucode is not found.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Freeing a buffer before calling hang() is superfluous. Removing the call
reduces the SPL size.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Calling calloc() for 0 members does not make any sense.
Setting ch_priv->busy_desc = NULL for ch_priv->desc_cnt > 0 is equally
unreasonable.
The current code will lead to a NULL dereference in bcm6348_iudma_enable().
The assignments for ch_priv->busy_desc are obviously swapped.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This adds basic register access and child regulator binding
for the Monolithic MP5416 Power Management IC which integrates
four DC/DC switching converters and five LDO regulators.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add low level platform initialization for the AST2600 SoC.
The 2-stage booting with U-Boot SPL are leveraged to support
different booting mode.
However, currently the patch supports only the booting from
memory-mapped SPI flash.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Add controller reset support through the
System Control Unit (SCU) of AST2600 SoC.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
AST2600 has 8 watchdog timers including 8 sets of
32-bit decrement counters, based on 1MHz clock.
A 64-bit reset mask is also supported to specify
which controllers should be reset by the WDT reset.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
AST2600 supports DDR4 SDRAM with maximum speed DDR4-1600.
The DDR4 DRAM types including 128MbX16 (2Gb), 256MbX16 (4Gb),
512MbX16 (8Gb), 1GbX16 (16Gb), and 1GbX8 TwinDie (16Gb) are supported.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
This patch adds the clock control driver
for the AST2600 SoC.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Add Cortina Access parallel Nand support for CAxxxx SOCs
Signed-off-by: Kate Liu <kate.liu@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Tom Rini <trini@konsulko.com>
CC: Scott Wood <oss@buserror.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
The driver only needs to retrieve the pin for the ACPI info. The driver
itself works without depending on GPIO.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
CC: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Update qemu-riscv.rst build instructions.
- Add support for SPI on Kendryte K210.
- Add Microchip PolarFire SoC Icicle Kit support.
- Add support for an early timer.
- Select TIMER_EARLY to avoid infinite recursion for Trace.
Implement get_pin_muxing() callback so that pinmux status
command can be used on Renesas platforms.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
By default on startup all the pin types are configured to
PINMUX_TYPE_NONE (in sh_pfc_map_pins()), when pin is set as GPIO the
pin type is updated to PINMUX_TYPE_GPIO. But the type is not updated
when the pin is set as a function in sh_pfc_pinctrl_pin_set() or
sh_pfc_pinctrl_group_set() calls (these calls only set the MUX if
the pin type is PINMUX_TYPE_NONE ie unused).
So with the current implementation pin functionality could be overwritten
silently, for example if the same pin is added for SPI and serial.
This patch makes sure of updating pin type after every successful call to
sh_pfc_config_mux() and thus fixing from pin functionality to be
overwritten. Also a warning message is printed if the current pin is being
overwritten before abort.
This also avoids pin re-muxing to same type that is for example from
command line device is asked to re-probe/select (mmc dev x) we return
early with success in this case as the pin is already muxed.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Add clock driver code for the Microchip PolarFire SoC. This driver
handles reset and clock control of the Microchip PolarFire SoC device.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Read phy address from device tree and use it to find the phy device
if not found then search in the range of 0 to 31.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Enable 32-bit or 64-bit DMA in the macb driver based on the macb
hardware compatibility and it is configured with structure macb_config
in the driver.
The Microchip PolarFire SoC Memory Protection Unit(MPU) gives the 64-bit
DMA access with the GEM, the MPU transactions on the AXI bus is 64-bit
not 32-bit So 64-bit DMA is enabled for the Microchip PolarFire SoC GEM.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Added support for timer_early_get_count() and timer_early_get_rate()
This is mostly useful in tracing.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The macro BIT_MASK is already defined in include/linux/bitops.h. To avoid
name collisions rename BIT_MASK() in drivers/ram/k3-j721e/lpddr4_private.h
to LPDDR4_BIT_MASK().
Remove superfluous parantheses.
Remove superfluous comparison to 0.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
log.h and dm/devres.h are U-Boot includes. So placing them
behind #ifndef __UBOOT__ does not make any sense.
Fixes: f7ae49fc4f ("common: Drop log.h from common header")
Fixes: 61b29b8268 ("dm: core: Require users of devres to include the header")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
U-Boot DM model probe only single device at a time
which is enabled and configured using device tree
or platform data method.
PL011 UART IP is SBSA compliant and firmware does the
serial port set-up, initialization and let the kernel use
UART port for sending and receiving characters.
Normally software talk to one serial port time but some
LayerScape platform require all the UART devices enabled
in Linux for various use case.
Adding support to probe all enabled serial devices like SBSA
compliant PL011 UART ports probe and initialization by firmware.
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Support a common method to probe all devices associated with uclass.
This includes data structures and code for finding the first device and
looping for remaining devices associated with uclasses (groups of devices
with the same purpose, e.g. all SERIAL ports will be in the same uclass).
An example is SBSA compliant PL011 UART IP, where firmware does the serial
port initialization and prepare uart device to let the kernel use it for
sending and reveiving the characters.SERIAL uclass will use this function
to initialize PL011 UART ports.
The feature is enabled with CONFIG_DM.
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
power/regulator will not be built if just CONFIG_SPL_DM_REGULATOR is
enabled. It needs CONFIG_SPL_POWER_SUPPORT to be enabled as well.
For example, if we just need a GPIO regulator in SPL:
CONFIG_DM_REGULATOR=y
CONFIG_SPL_DM_REGULATOR=y
CONFIG_DM_REGULATOR_GPIO=y
CONFIG_SPL_DM_REGULATOR_GPIO=y
Will not suffice, since the entire regulator build for SPL depends on
CONFIG_SPL_POWER_SUPPORT. Elaborate that information in the Kconfig
dependency.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
During build of simple panel driver backlight is needed so let's enable
it:
aarch64-linux-gnu-ld.bfd: drivers/built-in.o: in function `simple_panel_set_backlight':
u-boot/drivers/video/simple_panel.c:43: undefined reference to `backlight_set_brightness'
aarch64-linux-gnu-ld.bfd: drivers/built-in.o: in function `simple_panel_enable_backlight':
u-boot/drivers/video/simple_panel.c:28: undefined reference to `backlight_enable'
Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
write_mbr_partition() function name is a bit misleading, so rename it to
write_mbr_sector(). This is a preparation for adding code for writing a
complete MBR partition layout.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Add a return value to bb_miiphy_init and use it directly in the
post-relocation init sequence, rather than using a wrapper stub.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a return value to xen_init and use it directly in the
post-relocation init sequence, rather than using a wrapper stub.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a return value to pci_init and use it directly in the post-relocation
init sequence, rather than using a wrapper stub.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a return value to pci_ep_init and use it directly in the
post-relocation init sequence, rather than using a wrapper stub.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Something was wrong in the merge process into the mainline.
Some added patches access driver structure fields and functions that
have been modified by previous patches.
The patch renames:
- dev_get_platdata to dev_get_plat
- dev_get_uclass_platdata to dev_get_uclass_plat
- ofdata_to_platdata to of_to_plat
- plat_data_alloc_size to plat_auto
- priv_auto_alloc_size to priv_auto
- video_uc_platdata to video_uc_plat
Signed-off-by: Dario Binacchi <dariobin@libero.it>
In non-secure mode (EL2), FPGA reconfiguration driver calls the
SMC/PSCI services provided by ATF to configure the FPGA.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
In non-secure mode (EL2), MAC driver calls the SMC/PSCI services
provided by ATF to setup the PHY interface.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
In non-secure mode (EL2), MMC driver calls the SMC/PSCI services
provided by ATF to set SDMMC's DRVSEL and SMPLSEL.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Change 'clksel' callback function to allow the code to return a
status.
This patch is a preparation for enabling Arm-Trusted-Firmware (ATF)
in Intel SoC FPGA. This patch does not change functionality.
When using Arm-Trusted-Firmware (ATF) in Intel SoC FPGA, the MMC clock
related register is secure register which is required to be written
via SMC/PCSI call. It is possible that U-Boot fail to write the
register if there is unexpected error between U-Boot and ATF.
As a result, there maybe signal integrity on MMC connection due to
clock. So, the code should reports error to user when 'clksel' fail.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
- Update MAINTAINERS emails for STI and STM32
- Activate OF_LIVE for ST stm32mp15 boards
- Switch to MCO2 for PHY 50 MHz clock for DHCOM boards
- Correction in stm32prog command on uart: always flush DFU on start command
- Update USB-C power detection algorithm on DK boards
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl/+yLkACgkQ4rK92eCq
k3X/Fgf/d/11WyQrVzvpr+nN+4Wl7J+ASmoUz0yKa6ri+lbvhLgh+JXbCRKgRPWu
vNnI07pSoX/QeaMpGBU8Ztg/Onb9/pvffz4WMk1411GoyCpDFuuK3cVSIoqkPfu+
XmgSX0u4BXtve1+ZdWfVBWXawUSEDMmGR3tmz1708c/s/oYpnVeRDcqiqzJ94cWE
yt+SpMPVqMUVQ/rAGkE8ToSMxX7FusEa7SvCg4U2ikoRWs3kPpr/73+tRWlmgGxL
sW8SXSKiOmFyheSBx3d2B9n00kDYTTrQmbW9hlMilZmji7CwZYxgTCMdX0x4DeFP
RDajT2Yju1JmeM+Z8+Ke2tupzvy6QA==
=oK8C
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210113' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Enable logging features for stm32mp15 boards
- Update MAINTAINERS emails for STI and STM32
- Activate OF_LIVE for ST stm32mp15 boards
- Switch to MCO2 for PHY 50 MHz clock for DHCOM boards
- Correction in stm32prog command on uart: always flush DFU on start command
- Update USB-C power detection algorithm on DK boards
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change debug/pr_* to log_* or dev_* macro and define LOG_CATEGORY.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change debug/pr_debug to log_debug or dev_dbg macro and
define LOG_CATEGORY.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change pr_debug to log_debug or dev_dbg macro and define LOG_CATEGORY.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change debug to dev_dbg macro and define LOG_CATEGORY.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Change debug to dev_dbg macro and define LOG_CATEGORY.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change debug to dev_dbg macro and define LOG_CATEGORY.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change debug and pr_ macro to dev macro and define LOG_CATEGORY.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change debug and pr_ macro to dev macro and define LOG_CATEGORY.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change debug and pr_ macro to dev macro and define LOG_CATEGORY.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change debug and pr_err to dev macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change debug and pr_err to dev macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Define LOG_CATEGORY, use dev_ macro when it is possible.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Define LOG_CATEGORY, use dev_ macro when it is possible
and migrate other trace to log_ macro.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Define LOG_CATEGORY, change debug to dev_dbg and remove "%s:" __func__
header as it is managed by dev macro (dev->name is displayed)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Define LOG_CATEGORY and remove unneeded pr_fmt macro with the dev
macro as dev->name is displayed and CONFIG_LOGF_FUNC can be
activated for log macro.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change debug to dev_dbg macro and define LOG_CATEGORY.
Remove dev->name as it is already displayed by dev macro.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change debug to log macro and define LOG_CATEGORY.
Remove "%s:" with __func__ as it is managed by log macro
(CONFIG_LOGF_FUNC)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Remove unused function in exynos_dw_mmc.c.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
ARMv8's generic timer[1] picks up it's graycode from GTC. However,
the frequency of the GTC is supposed to be programmed in CNTFID0[2]
register prior to enabling the GTC in CNTCR[3] register.
In K3 architecture, GTC provides a central time to many parts of the
SoC including graycode to the generic timer in the ARMv8 subsystem.
However, due to the central nature and the need to enable the counter
early in the boot process, the R5 based u-boot enables GTC and
programs it's frequency based on central needs of the system. This
may not be a constant 200MHz based on the system. The bootloader is
supposed to program the FID0 register with the correct frequency it
has sourced for GTC from the central system controller OR from PLLs
as appropriate, and TF-A is supposed[4] to use that as the frequency for
it's local timer.
Currently we are programming just the CNTCR[3] register to enable the
GTC, however we dont let TF-A know the frequency that GTC is actually
running at. A mismatch in programmed frequency and what we program for
generic timer will, as we can imagine, all kind of weird mayhem.
So, program the CNTFID0 register with the clock frequency. Note:
assigned-clock-rates should have set the clock frequency, so the only
operation we need to explicitly do is to retrieve the frequency and
program it in FID0 register.
Since the valid in K3 for GTC clock frequencies are < U32_MAX, we can
just cast the ulong and continue.
[1] https://developer.arm.com/documentation/100095/0002/generic-timer/generic-timer-register-summary/aarch64-generic-timer-register-summary
[2] https://developer.arm.com/docs/ddi0595/h/external-system-registers/cntfid0
[3] https://developer.arm.com/docs/ddi0595/h/external-system-registers/cntcr
[4] 6a22d9ea3c
Signed-off-by: Nishanth Menon <nm@ti.com>
The schedule for deprecating the features of the pre-driver-model puts
2019.17 as the deadline for the video subsystem. Furthermore, the latest
patches applied to the am335x-fb.c module have decreased the amount of
code shared with the pre-driver-model implementation. Splitting the two
implementations into two modules improves the readability of the code
and will make it easier to drop the pre-driver-model code.
I have not created a header file with the data structures and the
constants for accessing the LCD controller registers, but I preferred to
keep them inside the two c modules. This is a code replication until the
pre-driver-model version is dropped.
Signed-off-by: Dario Binacchi <dariobin@libero.it>