Add a virtual partition to update the pmic non volatile memory.
(on ST board, STPMIC1).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a virtual partition to update the STM32MP15x OTP based
on SMC service provided by TF-A.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support for delete option 'D' in flashlayout for
full device or for partitions
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
For reliability of boot from NAND/SPI-NAND (with read-disturb issue)
the SSBL can be present several time, when it is indicated in the
flashlayout with "Binary(X)".
The received binary is copied X times by U-Boot on the target.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Dynamically adapt the MTD partitions in NOR/NAND/SPI-NAND when stm32prog
command detects in the parsed flash layout files:
- a fsbl partition in NOR.
- a tee partition in NOR/NAND/SPI-NAND
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of MTD device (DFU_MTD backend) for
NOR, NAND or SPI-NAND target.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of partial update, update only some partitions,
and check the coherence of the layout with the existing GPT
partitions (offset and size).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of eMMC device boot partition with
part_id = -1 for offset="boot1"
or = -2 for offset="boot2"
The stm32prog command configures the MMC DFU backend with "mmcpart"
and configure the eMMC (command "mmc bootbus" and "mmc partconf")
when the update is done.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of MMC device (based on DFU_MMC backend)
for SD card and eMMC update.
Create a GPT partitioning on the device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Build the list of device and of partition with
a tab separated value file with a stm32 header: the FlashLayout.tsv
(https://wiki.st.com/stm32mpu/wiki/STM32CubeProgrammer_flashlayout)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a specific command stm32prog for STM32MP soc family
witch allows to program the boot devices with the tool
STM32CubeProgrammer (http://www.st.com/STM32CubeProg).
This command uses the same UART STM32 protocol than MCU
STM32 with or USB with DFU protocol v1.1 (ithe MCU ST
extension are no supported).
The executed actions are based on a tab separated value file
with a stm32 header, the FlashLayout file
(https://wiki.st.com/stm32mpu/wiki/STM32CubeProgrammer_flashlayout).
This file is parsed by the U-Boot command to:
- initialize the devices
- create the partition table on each device
- initialize the DFU backend to access to not volatile memory
(NOR/NAND/SD/eMMC) or to virtual device (OTP/PMIC)
Up to STM32PROG_MAX_DEV (5) devices can be updated with a FlashLayout.
The communication between U-Boot and STM32CubeProgrammer is done with
the specific alternate configuration (see "AN5275: USB DFU/USART protocols
used in STM32MP1 Series bootloaders" for details).
The command stm32prog is executed when a boot from USB is detected
(selected with bootpins) and we can program the boot devices with
a simple command (on Windows or Linux):
PC $> STM32_Programmer_CLI -c port=usb1 -w flaslayout.tsv
1/ the ROM code loads TF-A in embedded RAM (DFU or uart)
2/ TF-A loads flashlayout file and U-Boot in DDR (DFU or uart)
3/ U-Boot executes the stm32prog command (DFU or uart)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a function get_cpu_dev to get the DEV_ID present
in DBGMCU_IDC register.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Manage BOOT_FLASH_SPINAND, with boot_device="spi-nand"
and treat this value in bootcmd_stm32mp.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Save and use the FDT address provided by TF-A in r2 at boot time
(it is NT_FW_CONFIG = Non Trusted Firmware configuration file)
Address is saved in save_boot_params(), called by start.S
and the used DTB is gd->fdt_blob = board_fdt_blob_setup().
If dtb is not provided or invalid, U-Boot use as fallback
the builtin DTB.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate OP-TEE driver for trusted and optee defconfig.
This driver allows detection of TEE presence for boot from flash;
CONFIG_STM32MP1_OPTEE is also removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add reserve memory for OP-TEE in U-Boot and in kernel device tree:
- no more reduce the DDR size in "memory" node:
CONFIG_SYS_MEM_TOP_HIDE is no more used
- U-Boot device-tree defines the needed "reserved-memory" for OP-TEE
and U-Boot should not use this reserved memory: board_get_usable_ram_top
use lmb lib to found the first free region, the not reserved
memory, enough to relocate U-Boot: the needed size of U-Boot
is estimated with gd->mon_len + CONFIG_SYS_MALLOC_LEN.
- the optee node ("optee@...": firmware with compatible "linaro,optee-tz")
and the associated "reserved-memory" are deactivated in kernel device
tree when OP-TEE is not detected by U-Boot to prevent kernel issue
(memory is reserved but not used, optee driver probe failed).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The DHCOR board does exist in multiple variants with different DDR3
DRAM sizes. To cater for all of them, implement DDR3 code handling.
There are two GPIOs which code the DRAM size populated on the SoM,
read them out and use the value to pick the correct DDR3 config.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Adjust the DDR configuration dtsi such that they only generate the
DRAM configuration node, the DDR controller node is moved into the
stm32mp157-u-boot.dtsi itself. This permits including multiple DDR
configuration dtsi files in board DT.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The AV96 board does exist in multiple variants. To cater for all of
them, implement board code handling. There are two GPIOs which code
the type of the board, read them out and use the value to pick the
correct device tree from an fitImage.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: Iddb330b9a66500495885457cbe17edc0eacaaf43
Add weak implementation of board_early_init_f() hook into the
STM32MP1 SPL. This can be used to read out e.g. configuration
straps before initializing the DRAM.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Add reset phandle to EHCI device tree node to make on-chip reset
controller usable with EHCI.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
While the nearly-universal default for the Raspberry Pi family is to use
spin tables and the spin table implementation provided by the Raspberry Pi
Foundation, FreeBSD and others may use a PSCI implementation instead.
Accommodate these setups by allowing them to configure for more than one
page to be reserved in the initial reservation. The default reservation
remains as one page.
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
At present the pinctrl nodes are not enabled in pre-relocation U-Boot so
the UARTs do not correctly select the pinconfig to enable the UART pins.
Fix this so that the U-Boot banner is printed.
This fixes serial output on rpi_3b_32b with the following config.txt
options:
enable_uart=1
gpu_freq=250
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 9821636b64 (bcm2835_pinctrl: Probe pre-reloc)
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Add tests for testing open-drain/open-source emulation in gpio-uclass.
It also adds two test3-gpios configured as GPIO_ACTIVE_LOW.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable the second USB controller, which is connected to a hub with 4
ports. The first controller is for the OTG port and is currently not
supported.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
[narmstrong: removed useless DWC2_UTMI_WIDTH in meson64.h]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The memory allocated to store the FIT image containing SYSFW and board
configuration data is statically defined to the largest size expected.
Some additions to the board configuration data has pushed us slightly
over the current defined size on some HS devices, expand to 278000.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Clients that are requesting some of uclass API's
without a device (with ofnode) usually have _nodev
naming convention.
- clk_get_by_index_nodev
- clk_get_by_name_nodev
- reset_get_by_index_nodev
- gpio_request_by_name_nodev
So, update the same naming convention PHY framework.
This doesn't change the existing functionality.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
When we create software partition, we still need let parent
partition to configure sid, so move the check after sid failed.
Acked-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add code to check m4 partition booted or not, we will use this
to runtime set device tree file that passed to Linux Kernel.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
For fspi build, we will enable both SPL NOR support and SPL SPI
support. SPL will dynamically check the resource owner then
select corresponding boot device.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When doing partition reboot, the boot image won't be reloaded by ROM,
it is just CPU reset to boot entry. The SW has to keep the boot image
inside the RAM unchanged. It includes both the TEXT section and DATA
section.
For SPL, the problem is DATA section will be updated at runtime, so in
next partition reboot the data is not same as the initial value from
cold boot. If any code depends on the initial value, then it will have
problem.
This patch introduces a mechanism to recover the data section
for partition reboot. It adds a new section in image for saving
data section. When from cold boot, the data section will be saved
to that new section at SPL early phase. When from partition reboot,
the data section will be restored from the new section.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Make sure that all devices that are powered up by SPL are powered down
before entering into the u-boot. Otherwise the subsystem/device will
never be powered down by SCFW, due to SPL and u-boot are in different
partitions.
Benefiting from power domain driver, this patch implements the function
"imx8_power_off_pd_devices" to power off all active devices.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When Trusty OS allocates the mem region from 0xfe0000000-0xffffffff,
the get_effective_memsize does not return correct memory size.
There is a check in get_effective_memsize to find the memreg where
the u-boot is running, and return the size of that memreg as the result
of get_effective_memsize. When using aligned start, the value is
0x80200000 since it is 2MB aligned. Thus the finding of memreg will
fail and return the PHYS_SDRAM_1_SIZE because u-boot text base is
0x80020000. This cause u-boot is relocated to the high memory where has
been occupied by Trusty OS.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The DDR memory from 0x88000000 to 0x8FFFFFFF is assigned to M4 on
QM and QXP. The M4 can allocate this memory by two ways,
in SCD or u-boot.
In this patch, u-boot addes the memory reserve node to DTB to pass
the info to kernel, no matter the M4 memory is reserved in SCD
or u-boot. So kernel won't access M4 reserved memory.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
add support for imx8qxp to read boot search count from fuse in nandbcb
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The original nandbcb tool was designed for imx6 only, when trying to
leverage it to replace the kobs-ng tool, we found the design is not
friendly for supporting all platforms. To support all iMX6/7/8 platforms
and for easy further maintain, I reconstruct the structure of the tool.
The main changes including:
1. Use platform_data to determine the logic branches rather than simply
use SOC name.
2. More data structures as parameter for functions.
3. Global variables to define the FCB/DBBT/FW locations.
4. Implement the kobs-ng default 4 FCB/4 DBBT/2 FW layout.
5. Support Hamming coding/ 40bit BCH/ 62bit BCH coding FCB.
6. Dump and compare all written FCB/DBBT to verify data integrity.
The tool has been verified on iMX6Q/DL, 6SX, 7D, 6ULL, iMX8QX, iMX8MM.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested on i.MX8MM EVK, imx8mm evk uses BCH
encoding and randomizer
modify macro and print size_t with %zx
use CONFIG_IMX8M because it should apply to imx8mq/mm/mn
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
bchtype in FCB should be associated to the gf_13/14 settings in BCH, fix
the issue and test on Micron 29F64G08CBABB, it can boot after the
change.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
We are currently using SC_R_LAST as a marker for imx8 power domain tree
nodes without a resource attached. This value is compiled into dtb as
part of the linux build and used by uboot.
The SC_R_LAST constant changes frequently as SCFW resources are added
(by design) and every time we need to update linux and uboot headers
together or boot can fail.
Fix this by replacing SC_R_LAST usage with a new constant SC_R_NONE
defined to be 0xFFF0.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add power_domain_lookup_name interface to power domain uclass to find
a power domain device by its DTB node name, not using its associated
client device.
Through this interface, we can operate the power domain devices directly.
This is needed for non-DM drivers.
Modified from Ye's NXP downstream patch
only for legacy imx8 power domain driver, since we have not migrated
to use new power domain driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Beacon EmbeddedWorks, formerly known as Logic PD, is releasing
a devkit based on the i.MX8M Mini SoC consisting of baseboard +
SOM.
It supports eMMC on the SOM, microSD on the baseboard, various
GPIO, the PINCTRL, and UART.
Signed-off-by: Adam Ford <aford173@gmail.com>
enable the GPMI NAND driver for i.MX8, i.MX8 use similar controller as
i.MX8M
- register definition for i.mx8
- DMA structure must be 32bit address
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update the gpmi/apbh_dma/bch drivers and relevant registers for i.MX8M.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch is a porting of
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/
commit/?h=imx_4.1.15_1.0.0_ga&id=e4dacc44d22e9474ec456cb330df525cd805ea38
"
i.MX6QP and i.MX7D BCH module integrated a new feature to detect the
bitflip number for erased NAND page. So for these two platform, set the
erase threshold to gf/2 and if bitflip detected, GPMI driver will
correct the data to all 0xFF.
Also updated the imx6qp dts file to ditinguish the GPMI module for i.MX6Q
with the one for i.MX6QP.
"
In this patch, i.MX6UL is added and threshold changed to use ecc_strength.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
So far u-boot only load SNSR25C for TMU main probe (probe 0). However,
kernel enables two probes. So it also needs to set default SNSR25C of
TCALIV1 for blank samples.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MP thermal which has two probes and supports temperature range
from -40 to 125. The driver still uses default 1p HW
calibration at 25C and loads calibration parameters from fuse.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Like iMX8MM, iMX8MN also needs SW to load TMU TASR and TCALIV registers
value from fuse before enabling TMU calibration. Otherwise the calibration
is not exact.
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On iMX8MM, the default value of TMU registers TCALIV and TASR need
be loaded from fuse. HW won't do this, it expect SW loads them before
using TMU.
Reviewed-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
imx_get_mac_from_fuse is used to load MAC address from fuse. On imx8mp,
we have two different ENET controllers and both need to call this
function. So decouple its declare from fec driver.
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There are different parts from one SoC. Take i.MX6ULL for example,
some part might not have ENET, some might have; some might not have
USB, some might have. The information could be got from OCOTP,
to make one image support the different parts, we need runtime
disable linux kernel dts node and uboot driver probe if the
corresponding module not exists in the part.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add initial support for Technexion Pico-iMX8MQ SoM on PicoPI carrier
board. Currently working is ethernet, serial, eMMC. DT is imported
from Linux 5.4.28 ("462afcd6e7ea") .
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
If dcache is switched OFF to ON state and if non-cached memory is
used, this non-cached memory must be re-declared as uncached to mmu
each time dcache is set ON.
Introduce noncached_set_region() to set this non-cached region's mmu
settings. Let architecture override it by defining it as a weak
function.
For ARM architecture, noncached_set_region() defines all noncached
region as non-cacheable.
Issue found on STM32MP1 platform using dwc_eth_qos ethernet driver,
when going from dcache OFF to dcache ON state, ethernet driver issued
TX timeout errors when performing dhcp or ping.
It can be reproduced with the following sequence:
dhcp
while true ; do
ping 192.168.1.300 ;
dcache off ;
ping 192.168.1.300 ;
dcache on ;
done
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The Juno board features a standard compliant EHCI/OHCI USB host
controller pair, which we can just enable.
The platform data is taken from the device tree.
This allows to use USB mass storage (the only storage on a Juno r0)
for loading.
At least on my board USB seems a bit flaky, I need two "usb reset"
sequences after the "usb start" to detect an USB hard drive.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
So far the Juno board wasn't implementing reset. Let's just use the
already existing PSCI_RESET based method to avoid any extra code.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Arm Juno board was still somewhat stuck in "hardcoded land", even
though there are stable DTs around, and one happens to actually be on
the memory mapped NOR flash.
Enable the configuration options to let the board use OF_CONTROL, and
add a routine to find the address of the DTB partition in NOR
flash, to use that for U-Boot's own purposes.
This can also passed on via $fdtcontroladdr to any kernel or EFI
application, removing the need to actually load a device tree.
Since the existing "afs" command and its flash routines require
flash_init() to be called before being usable, and this is done much
later in the boot process, we introduce a stripped-down partition finder
routine in vexpress64.c, to scan the NOR flash partitions for the
DT partition. This location is then used for U-Boot to find and probe
devices.
The name of the partition can be configured, if needed, but defaults
to "board.dtb", which is used by Linaro's firmware image provided.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Add DM model for P1010RDB
- Add I2C DM Model support for P1010RDB, T1042RDB, T2080, T4240RDB,
MPC8548CDS, T1024RDB, P4080, P3041DS, P2041RDB, P2020RDB, P1020RDB,
P5040DS
- Fix reference to READM.qe_firmware
- dts clean up to use -u-boot for px30, rk3399 boards
- dts sycn from upstream kernel for rk3328, rk3399
- add rockchip rng driver
- new board support: rk3328-roc-cc, rk3399-roc-pc,Nanopi M4 2GB
Make a few adjustments to allow us to build an SPL image for coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
At present SPL only works on bare-metal builds. With a few tweaks it can
be used for coreboot also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
At present this function copies U-Boot from the last 1MB of ROM. This is
not the right way to do it. Instead, the binman symbol should provide the
location.
But in any case the code should live in the caller,
spl_board_load_image(), so that the 64-bit jump function can be used
elsewhere. Move it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Coreboot runs in 32-bit mode and cannot run a 64-bit U-Boot. To get around
this we can build a combined image with 32-bit SPL and 64-bit U-Boot. Add
a build rule and binman definition for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
At present this function is only available in 32-bit code. Move it to the
common cpu file so it can be used by 64-bit U-Boot too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This resolves issues with certain SFP modules.
Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Add device tree for P1010RDB boards and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Provide a common i2c components that we can utilize to
build up the various device tree.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add REVC informaiton.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add a test item for the phy_bulk API
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add a test item for ofnode_get_child_count()
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
The correct syntax is 'select SYS_...' and not 'select CONFIG_SYS...'
Fixes: d5c819b885 ("actions: Move defconfig options to Kconfig")
Signed-off-by: Tom Rini <trini@konsulko.com>
CONFIG_SPL_FAT_SUPPORT was removed in commit 0c3a9ed409
("spl: Kconfig: Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT").
Fixup a leftover use of the symbol.
Fixes: 9d86dbd9cf ("imx: spl: implement spl_boot_mode for i.MX7/8/8M")
Signed-off-by: Harald Seiler <hws@denx.de>
It is hard to read code which contains nested ifdef blocks. Replace
them with normal if-blocks and the IS_ENABLED() macro. This is not only
more readable but also helps as both arms are validated by the compiler
in all cases.
Signed-off-by: Harald Seiler <hws@denx.de>
The CONFIG_SPL_FORCE_MMC_BOOT config flag is not needed as its behavior
is the correct one in all cases; using spl_boot_device() instead of the
boot_device parameter will lead to inconsistency issues, for example,
when a board_boot_order() is defined. In fact, this is the reason the
parameter was introduced in the first place, in commit 2b1cdafa9f
("common: Pass the boot device into spl_boot_mode()").
This reverts commit 772b55723b.
Link: https://lists.denx.de/pipermail/u-boot/2020-April/405979.html
Signed-off-by: Harald Seiler <hws@denx.de>
Boards may extend or re-define the boot list in their board_boot_order()
function by modifying spl_boot_list. E.g. a board might boot SPL from a
slow SPI NOR flash and then load the U-Boot from an eMMC or SD-card.
Or it might use additional MMC boot device in spl_boot_list for cases
when the image in SPI NOR flash is not found, so it could fall back to
eMMC, SD-card or another boot device.
Getting the MMC boot mode in spl_mmc will fail when we are trying to
boot from an MMC device in the spl_boot_list and the original board
boot mode (as returned by spl_boot_device()) is not an MMC boot mode.
Fix it by checking the asked MMC boot device from the spl_mmc_boot_mode()
argument.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
initr_enable_interrupts() is an ARM-specific wrapper over
enable_interrupts(), which is run during the common init sequence. It can
be eliminated by moving the enable_interrupts() call to the end of
interrupt_init() function, in arch/arm/lib/interrupts*.c.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Solved the overflow on phys_addr_t type for start + size in
mmu_set_region_dcache_behaviour() function.
This overflow is avoided by dividing start and end by 2 before addition,
and we only expecting that start and size are even.
This patch doesn't change the current function behavior if the
parameters (start or size) are not aligned on MMU_SECTION_SIZE.
For example, this overflow occurs on ARM32 with:
start = 0xC0000000 and size = 0x40000000
then start + size = 0x100000000 and end = 0x0.
For information the function behavior change with risk of regression,
if we just shift start and size before the addition.
Example with 2MB section size:
MMU_SECTION_SIZE 0x200000 and MMU_SECTION_SHIFT = 21
with start = 0x1000000, size = 0x1000000,
- with the proposed patch, start = 0 and end = 0x1 as previously
- with the more simple patch:
end = (start >> MMU_SECTION_SHIFT) + (size >> MMU_SECTION_SHIFT)
the value of end change:
start >> 21 = 0, size >> 21 = 0 and end = 0x0 !!!
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add the new flags DCACHE_DEFAULT_OPTION to define the default
option to use according the compilation flags
CONFIG_SYS_ARM_CACHE_*.
This new compilation flag allows to simplify dram_bank_mmu_setup()
and can be used as third parameter (option=dcache option to select)
of mmu_set_region_dcache_behaviour function.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add protection in dram_bank_mmu_setup() to avoid access to bd->bi_dram
before relocation.
This patch allow to use the generic weak function dram_bank_mmu_setup
to activate the MMU and the data cache in SPL or in U-Boot before
relocation, when bd->bi_dram is not yet initialized.
In this cases, the MMU must be initialized explicitly with
mmu_set_region_dcache_behaviour function.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Move CONFIG_SYS_ARM_CACHE_WRITETHROUGH and
CONFIG_SYS_ARM_CACHE_WRITEALLOC into Kconfig done by moveconfig.py.
Kconfig uses a choice between the 3 values supported in U-Boot,
including the new configuration CONFIG_SYS_ARM_CACHE_WRITEBACK
(the default configuration).
The patch also avoids to select simultaneously 2 configurations.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add initial support for Google's Coral Dev Board based on i.MX8MQ.
https://coral.ai/products/dev-board
The Phanbell naming has been used here to match the naming convention
used in Google's U-Boot source tree:
https://coral.googlesource.com/uboot-imx/
Co-developed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Tested-by: Marco Franchi <marcofrk@gmail.com>
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
imx8m has the only implementation of reset_cpu() which does not ignore
the addr parameter and instead gives it some meaning as the base address
of watchdog registers. This breaks convention with the rest of U-Boot
where the parameter is ignored and callers are passing in 0.
Fixes: d2041725e8 ("imx8m: restrict reset_cpu")
Co-developed-by: Harald Seiler <hws@denx.de>
Signed-off-by: Harald Seiler <hws@denx.de>
Signed-off-by: Claudius Heine <ch@denx.de>
The SPL can also be compiled with sysreset drivers just fine, so
update the condition to cater for that option.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
If the cpu-idle-states is missing from the DT in the first place, do
not fail on removing in. Just move on and do not even print an error,
since not being able to remove something which is not there in the
first place is not an error and surely does not justify failing to
boot.
Turn the surrounding prints into debugs to reduce the useless noise.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This patch synchronizes the device tree with that from 5.6.7.
This also adds nodes for crypto and ddrc, which makes keeping
the device tree files from individual boards in sync with the
Linux kernel. This is helpful when boads reference those nodes.
Signed-off-by: Adam Ford <aford173@gmail.com>
imx8m has the only implementation of `reset_cpu` which does not ignore
the addr parameter and instead gives it some meaning as the base address
of watchdog registers. This breaks convention with the rest of U-Boot
where the parameter is ignored and callers are passing in 0.
Fixes: d2041725e8 ("imx8m: restrict reset_cpu")
Co-Authored-by: Harald Seiler <hws@denx.de>
Signed-off-by: Claudius Heine <ch@denx.de>
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
In case CONFIG_SYSRESET is set, do_reset from reset.c will not be available
anywere, even if SYSRESET is disabled for SPL/TPL.
'do_reset' is called from SPL for instance from the panic handler and
PANIC_HANG is not set
Signed-off-by: Claudius Heine <ch@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Add a module to configure the tamper and secure violation of
the SNVS using the SCU API.
The module also adds some commands:
- snvs_cfg: Configure the SNVS HP and LP registers
- snvs_dgo_cfg: Configure the SNVS DGO bloc if present (8QXP)
- tamper_pin_cfg: Change the configuration of the tamper pins
- snvs_clear_status: Allow to write to LPSR and LPTDSR to clear
status bits
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the latest SCFW API with below commit
6dcd0242ae7a53ac ("SCF-105: Revert accidental change") to add
interfaces for PM resource reset and read/write SNVS security
violation and tamper DGO registers.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When doing reset_cpu, in normal case the WDOG_B outputs immediately
after we clean WDA bit. But on mscale, the WDOG_B may be later than
internal reset, and cause PMIC not reset. As we enabled the SD3.0
support, the PMIC must be reset to reset SD card.
Change the reset_cpu to enable the WDOG_B for timeout as well, and set
WDOG timeout to 1s.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The fracpll decoding is using the bit definitions for int pll. Most of
them are same, but the CLKE bit is different. Fix the wrong CLKE_MASK
for fracpll and correct all bit definitions in fracpll decoding.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In SPL build, the formatting '%llx' in debug() is not supported.
Also, fix some misplaced parameters in printf.
Modified from Seb Fagard's downstream patch
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In SPL build, the formatting '%llx' in debug() is not supported.
Also, fix some misplaced parameters in printf.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Seb Fagard <sebastien.fagard@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Latest SCFW has removed old MISC SECO commands. So update the codes
to use new SECO commands.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
parameter 'end address' must be inclusive of address range.
Modified from Seb's downstream patch.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the dump of DRAM PLL into "clocks" command
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
For ARM core clock, there are two input branches, and can select via mux:
one from ARM PLL directly, second from CCM A53 clock root.
Currently we are using second branch. But IC confirmed the CCM A53 root
signoff timing is 1Ghz, so we should switch to input from ARM PLL directly.
This patch fixes the CORE SEL slice configuration and switch ARM clock
to ARM PLL.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
iMX8MQ EVK board has a eMMC5.0 chip and supports SD3.0, so enable the UHS
and HS400 configs to enhance the eMMC/SD access.
The change also needs to set usdhc clock to 400Mhz, and add the
off-on-delay-us to SD reset pin, otherwise some SD cards will
fail to select UHS mode in re-initialization.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update clock root table to let it be easy to configure clock at
very early stage. Also the core_sel mux parent should be A53 CLK
root and ARM PLL.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acquire ATF commit hash when booting U-Boot to make user easy
to know the ATF version.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move the SIP macro to common header and unify the name to
make others could reuse them.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update is_imx6ull helper to include i.MX6ULZ SoC. i.MX6ULZ could
share same macro, then we no need to add is_imx6ulz in various drivers.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MP speed grade use same layout as i.MX8MN, so reuse it for i.MX8MP
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
imx8mn speed grade fuse uses new definitions as below. So have
to update get_cpu_speed_grade_hz function to match it.
SPEED_GRADE[5:4] SPEED_GRADE[3:0] MHz
xx 0000 2300
xx 0001 2200
xx 0010 2100
xx 0011 2000
xx 0100 1900
xx 0101 1800
xx 0110 1700
xx 0111 1600
xx 1000 1500
xx 1001 1400
xx 1010 1300
xx 1011 1200
xx 1100 1100
xx 1101 1000
xx 1110 900
xx 1111 800
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
According to iMX8MM datasheet (IMX8MMIEC_Rev_D and IMX8MMCEC_Rev_D),
the speed grading for imx8mm is 800Mhz, 1.2Ghz, 1.6Ghz and 1.8Ghz.
Update them to get_cpu_speed_grade_hz function.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
i.MX8MP use 0x182 as its ID, so 0xff is not valid to get the cpu type,
extend it to 0x1ff.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
All the FEC ethernet clock entries for iMX8MM are missing, while they
are already present on iMX8MQ. Fill in the nodes on iMX8MM, as the FEC
ethernet gets bogus clock information otherwise which makes ethernet
inoperable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
commit b2f5da9dd0 ("rockchip: rk3399: Add Nanopi M4 board support") added
support for Nanopi M4 board with Dual-Channel 4GB LPDDR3-1866 RAM.
This patch adds another variant of NanoPi M4 board with Dual-Channel
2GB DDR3-1866 RAM.
Signed-off-by: Deepak Das <deepakdas.linux@gmail.com>
Add Firefly ROC-RK3399-PC Mezzanine board which is an
extension board on top of roc-rk3399-pc.
Will drop the separate defconfig file, once we support
the board detection at runtime.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399 dts(i) files from v5.7-rc1 linux-next.
Reason:
To get updated PCIe nodes and properties on respective
dts(i) files.
Summary:
- sync won't include new board dts(i)
- sync will add required files used on respective dts(i)
- rk3399-puma-u-boot.dtsi spiflash label changed to norflash
- move puma.dtsi bios_enable into rk3399-puma-u-boot.dtsi
- move legacy max-frequency of sdhci into rk3399-u-boot.dtsi
- update cross-ec-[keyboard|sbs].dtsi path as per U-Boot
- keep roc-rk3399-pc dc_12v changes to -u-boot.dtsi
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Move U-Boot specific properties into rk3399-evb u-boot
specific dtsi file.
This would help to sync the devicetrees from Linux whenever
required instead of adding specific nodes.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Move U-Boot specific properties into rk3399-puma u-boot
specific dtsi file.
This would help to sync the devicetrees from Linux whenever
required instead of adding specific nodes.
Cc: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
If the VBUS regulator is always-on, XHCI will fail to detect USB 3.0
devices; USB 2.0 devices will work however.
Make the VBUS regulator controllable and tie it to only the XHCI. This
makes all three USB ports usable.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The ROC-RK3328-CC from Firefly and Libre Computer Project is a credit
card size development board based on the Rockchip RK3328 SoC, with:
- 1/2/4 GB DDR4 DRAM
- eMMC connector for optional module
- micro SD card slot
- 1 x USB 3.0 host port
- 2 x USB 2.0 host port
- 1 x USB 2.0 OTG port
- HDMI video output
- TRRS connector with audio and composite video output
- gigabit Ethernet
- consumer IR receiver
- debug UART pins
The ROC-RK3328-CC has the enable pin of the SD card power switch tied
to GPIO_0_D6. This pin also has the function SDMMC0_PWREN, which is
muxed by default. SDMMC0_PWREN is an active high signal controlled by
the MMC controller, however the switch enable is active low, and
pulled low (enabled) by default to make things work on boot.
As such, we need to mux away from SDMMC0_PWREN and use GPIO to enable
power to the card. The default GPIO state for the pin is pull-down and
input, which doesn't require extra configuration when paired with the
external pull-down and active low switch.
Deal with this by enabling regulator support in SPL, and setting
"u-boot,dm-spl" for the regulator and other device nodes needed for
muxing the pin.
The device tree file is synced from the Linux kernel next-20200324.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This syncs rk3328 device tree files from the Linux kernel next-20200324.
The last commit to touch these files is:
b2411befed60 ("arm64: dts: add bus to rockchip amba nodenames")
Additional changes not yet in the Linux kernel include:
arm64: dts: rockchip: rk3328: drop #address-cells, #size-cells from grf node
arm64: dts: rockchip: rk3328: drop non-existent gmac2phy pinmux options
arm64: dts: rockchip: rk3328: Replace RK805 PMIC node name with "pmic"
Changes include:
- conversion of raw pin numbers to macros
- removal of deprecated RK_FUNC_* macros
- update of device tree binding headers
- new devices
- device tree cleanups
- gmac2phy disabled in -u-boot.dtsi as it is not supported in U-boot
This includes a re-ordering of the USB device nodes compared to upstream
Linux, moving the dwc2 OTG controller after the EHCI/OHCI nodes. This is
currently required as otherwise the dwc2 controller would not be able to
detect devices in some cases. This may be due to lack of USB PHY support
in U-boot.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The "hnp-srp-disable" property for dwc2 is specific to U-boot, not part
of upstream Linux's device tree bindings.
Move it to rk3328-u-boot.dtsi to avoid losing it when syncing device
tree files.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The device tree file for rk3328-evb in the Linux kernel does not have
gmac2io enabled. Instead, gmac2phy is enabled, but that is not supported
in U-boot.
Move the gmac2io related nodes to rk3328-evb-u-boot.dtsi to preserve the
current functionality. When the device tree files are synced, gmac2phy
should be marked as "broken" in -u-boot.dtsi files.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Loic Devulder <ldevulder@suse.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
USB 3.0 is only supported in U-boot, not in the Linux kernel where the
device tree files are ultimately synced from. While the xhci node was
moved, the external vbus regulator was not.
Move it as well.
Fixes: 2e91e2025c ("rockchip: rk3328: migrate u-boot node to -u-boot.dtsi")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Loic Devulder <ldevulder@suse.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add U-Boot specific dts file for hifive-unleashed-a00, this
would help to add u-boot specific properties and other node
changes without touching the base dts(i) files which are easy
to sync from Linux.
Added spi2 alias for qspi2 as an initial u-boot specific
property change.
spi probing in current dm model is very much rely on aliases
numbering. Even though the qspi2 can't come under any associated
spi nor flash it would require to specify the same to make proper
binding happen for other spi slaves.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Sagar Kadam <sagar.kadam@sifive.com>
- Add DM_ETH support for DPAA1, DPAA2 based RDB platforms: ls1046ardb,
ls1043ardb, lx2160ardb, ls2088ardb, ls1088ardb.
- Add GICv3 support for ls1028a, ls2088a, ls1088a.
- Add lpuart support on ls1028aqds.
- Few bug fixes and updates on ls2088a, ls1012a, ls1046a, ls1021a based
platforms.
With chromebook_coral we normally run TPL->SPL->U-Boot. This is the
'bare metal' case.
When running from coreboot we put u-boot.bin in the RW_LEGACY portion
of the image, e.g. with:
cbfstool image-coral.serial.bin add-flat-binary -r RW_LEGACY \
-f /tmp/b/chromebook_coral/u-boot.bin -n altfw/u-boot \
-c lzma -l 0x1110000 -e 0x1110000
In this case U-Boot is run from coreboot (actually Depthcharge, its
payload) so we cannot access CAR. Use the existing stack instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If U-Boot is running from coreboot we need to skip low-level init. Add
an way to detect this and to set the gd flag.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To support detecting booting from coreboot, move the code which locates
the coreboot tables into a common place. Adjust the algorithm slightly to
use a word comparison instead of string, since it is faster.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct the comments to 960KB]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
When U-Boot is not the first-stage bootloader the interrupt and cache init
must be skipped, as well as init for various peripherals. Update the code
to add checks for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When U-Boot is not the first-stage bootloader the FSP-S init must be
skipped. Update it to add a check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useful to be able to boot the same x86 image on a device with or
without a first-stage bootloader. For example, with chromebook_coral, it
is helpful for testing to be able to boot the same U-Boot (complete with
FSP) on bare metal and from coreboot. It allows checking of things like
CPU speed, comparing registers, ACPI tables and the like.
When U-Boot is not the first-stage bootloader much of this code is not
needed and can break booting. Add checks for this to the FSP code.
Rather than checking for the amount of available SDRAM, just use 1GB in
this situation, which should be safe. Using 2GB may run into a memory
hole on some SoCs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useful to dump ACPI tables in U-Boot to see what has been generated.
Add a command to handle this.
To allow the command to find the tables, add a position into the global
data.
Support subcommands to list and dump the tables.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
We always write three basic tables to ACPI at the start. Move this into
its own function, along with acpi_fill_header(), so we can write a test
for this code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this code to a generic location so that we can test it with sandbox.
This requires adding a few new fields to acpi_ctx, so drop the local
variables used in the original code.
Also use mapmem to avoid pointer-to-address casts which don't work on
sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
We don't actually support tables without an XSDT so we can drop this dead
code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Call the new core function to permit devices to write their own ACPI
tables. These tables will appear after all other tables.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
The current code uses an address but a pointer would result in fewer
casts. Also it repeats the alignment code in a lot of places so this would
be better done in a helper function.
Update write_acpi_tables() to make use of the new acpi_ctx structure,
adding a few helpers to clean things up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
A device may want to write out ACPI tables to describe itself to Linux.
Add a method to permit this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Probe the FMan MACs based on the device tree while
retaining the legacy code/functionality.
One notable change introduced here is that, for DM_ETH,
the name of the interfaces is corrected to the fmX-macY
format, that avoids the referral to the MAC block names
which were incorrect for FMan v3 devices (i.e. DTSEC,
TGEC) and had weird formatting (i.e. FM1@DTSEC6, FM1@TGEC1).
The legacy code is left unchanged in this respect.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Introduce the QorIQ DPAA 1 Frame Manager nodes in the LS1046ARDB
device tree. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA 1 Frame Manager v3 device tree nodes for the
LS1046A SoC. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Introduce the QorIQ DPAA 1 Frame Manager nodes in the LS1043ARDB
device tree. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA 1 Frame Manager v3 device tree nodes for the
LS1043A SoC. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA Frame Manager v3 device tree nodes description.
The device tree fragments are copied over with little modification
from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Rename fsl-ls1028a-qds.dts to fsl-ls1028a-qds.dtsi so that
it can be used as common device tree for lpuart and duart.
Add lpuart device tree and duart device tree respectively
for qds which are used with duart and lpuart console.
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In order to maintain compatibility with the Linux DTS, the entire fsl-mc
node is added but instead of being probed by a dedicated bus driver it
will be a simple-mfd.
Also, annotate the external MDIO nodes and describe the PHYs (8 x
VSC8514, AQR105). Also, add phy-handles for the dpmacs to their
associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In order to maintain compatibility with the Linux DTS, the entire fsl-mc
node is added but instead of being probed by a dedicated bus driver it
will be a simple-mfd.
Also, annotate the external MDIO nodes and describe the PHYs (4 x AQR405
and 4 x CS4340). Also, add phy-handles for the dpmacs to their
associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In order to maintain compatibility with the Linux DTS, the entire fsl-mc
node is added but instead of being probed by a dedicated bus driver it
will be a simple-mfd.
Also, annotate the EMDIO1 node and describe the 2 AR8035 RGMII PHYs and
the 2 AQR107 PHYs. Also, add phy-handles for the dpmacs to their
associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the External MDIO1 device node found in the WRIOP global memory
region. This is needed for management of external PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the External MDIO1 device node found in the WRIOP global memory
region. This is needed for management of external PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the External MDIO device nodes found in the WRIOP global memory
region. This is needed for management of external PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add rng node in rk3399-u-boot.dtsi and enable it in
rk3399-evb-u-boot.dtsi.
Signed-off-by: Lin Jinhan <troy.lin@rock-chips.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove DT nodes which are not used by U-Boot, like audio and video in/out
nodes. This saves about 35 kiB on the resulting U-Boot binary without any
impact on functionality.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Synchronize R-Car Gen3 device trees with Linux 5.6.2,
commit 9fbe5c87eaa9b72db08425c52c373eb5f6537a0a .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Synchronize R-Car Gen2 device trees with Linux 5.6.2,
commit 9fbe5c87eaa9b72db08425c52c373eb5f6537a0a .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
- add GXBB USB PHY driver
- enable access to SPI NOR Flash on VIM2 and VIM3/VIM3L boards
- fix USB PHYs Power-Up on on VIM3/VIM3L boards
-----BEGIN PGP SIGNATURE-----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=e10O
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200428' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- fix sd-emmc controller A init on G12A/G12B/SM1 SoCs
- add GXBB USB PHY driver
- enable access to SPI NOR Flash on VIM2 and VIM3/VIM3L boards
- fix USB PHYs Power-Up on on VIM3/VIM3L boards
The file <board name>-u-boot.dtsi inculde automatically by the build
system, no need to add this to dts file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Move GIC redistributor tables initialization to CPU setup function.
This patch introduces a GIC redistributor tables init function, and
moves the function of reserving memory for GIC redistributor tables
to soc.c and adds a argument for the memory size to reserve, BTW
rename the function so that it is more readable.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The initialization of gd->arch.resv_ram pointer should depend on if the
RESV_RAM config is enabled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
roc-rk3399-pc has an FE1.1 USB 2.0 HUB which connects two USB ports
(HOST1 and HOST2). For end devices to work we need to enable USB hub
so that HOST detects there presence and enumerates them accordingly.
This requires explicit pinctrl within gpio enablement.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the SPI flash controller and reduce the usable eMMC data pins to 4
to permit using the on-board SPI NOR Flash.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Activate the on-board SPI NOR Flash by enabling the SPI controller and
disabling the DS eMMC pin in the VIM2 u-boot.dtsi file.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
- bmips: fix build error when disabling USB
- mips: add option to restore original exception vector base
- mips: fix off-by-one error when clearing gd_data
- mips: minor fixes for compatibility with generic SPL framework
- spl: refactor legacy image loading
- spl: add LZMA decompression support for legacy images
- Makefile: add target to build LZMA compressed U-Boot images
- mtmips: refactor and rewrite low-level init code
- mtmips: add and enable SPL support with LZMA
- mtmips: add support for MT7628 reference board
- mtmips: add support for VoCore/VoCore2 board
-----BEGIN PGP SIGNATURE-----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=2jL1
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-04-27' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips
- brcmnand: fix missing code path from Linux driver
- bmips: fix build error when disabling USB
- mips: add option to restore original exception vector base
- mips: fix off-by-one error when clearing gd_data
- mips: minor fixes for compatibility with generic SPL framework
- spl: refactor legacy image loading
- spl: add LZMA decompression support for legacy images
- Makefile: add target to build LZMA compressed U-Boot images
- mtmips: refactor and rewrite low-level init code
- mtmips: add and enable SPL support with LZMA
- mtmips: add support for MT7628 reference board
- mtmips: add support for VoCore/VoCore2 board
Small patch to add support for VoCore/VoCore2 board.
VoCore is open hardware and runs OpenWrt/LEDE.
It has WIFI, USB, UART, 20+ GPIOs but is only one inch square.
It will help you to make a smart house, study embedded system
or even make the tiniest router in the world.
Details about this SoM can be found at "https://vocore.io/v2.html".
Signed-off-by: Mauro Condarelli <mc5686@mclink.it>
Reviewed-by: Stefan Roese <sr@denx.de>
The current implementations have some issues detecting the correct
values:
dqs_find_max() will return "last passing fieldval + 1" instead of
"last passing fieldval". Also it will return "maxval + 1" in the
case that all fieldvals are tested valid (without error).
dqs_find_min() will not test the "lowest" value because of using ">"
instead of ">=".
This patch now rewrites these functions to fix those issues. Also,
this patch uses the same approach of a for loop in both functions making
it easier to read and maintain.
Since the variables are integers now, we can use min()/max(), which
handles the wrap around case for fieldval=0: return (0 - 1).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
This change is made to enable comparison of integer variables, which
might be negative in the next patch. No functional change is intended
in this patch.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
This function returns "-1" (true) upon error. So the function name does
not match its implementation which is confusing. This patch renames the
function to dqs_test_error() which makes the code easier to read.
Also change the return type to bool and return "true" or "false".
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds support for mt7628 reference board. SPL_DM and DT are not
enabled for SPL to save about 17KiB for u-boot-spl.bin.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch enables SPL for all mtmips boards. And also remove defconfig
files which are intend to build ram bootable u-boot files.
SPL_DM and OF_CONTROL are enabled for both boards.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds SPL support for mtmips platform. The lowlevel architecture
is split into SPL and the rest parts are built into a memory loadable
u-boot image. Optional SPL_DM and OF_CONTROL are also supported.
The increment of size is very small (< 10 KiB) if SPL_DM and OF_CONTROL are
not enabled and the memory bootable u-boot (u-boot.img) is generated
automatically so there is not need to add a separate config for it.
A lzma compressed payload (u-boot-lzma.img) is also generated and it will
be combined with u-boot-spl.bin to form the unified ROM bootable binary
u-boot-mtmips.bin.
A spl loader is added to support uncompress the payload.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch rewrites the mtmips architecture with the following changes:
1. Move MT7628 soc parts into a subfolder.
2. Lock parts of D-Cache as temporary stack.
3. Reimplement DDR initialization in C language.
4. Reimplement DDR calibration in a clear logic.
5. Add full support for auto size detection for DDR1 and DDR2.
6. Use accurate CPU clock depending on the input xtal frequency for timer
and delay functions.
Note:
print_cpuinfo() has incompatible parts with MT7620 so it's moved into
mt7628 subfolder.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The initial stack on some platforms is too small to hold a large malloc
space. This patch adds a option to allow these platforms not reserving the
malloc space on initial stack. These platforms should set the malloc base
after DRAM is usable.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Currently CONFIG_MIPS_INIT_STACK_IN_SRAM assumes the memory space for the
initial stack can be used directly. However on some platform the SRAM needs
initialization, e.g. lock cache.
This patch adds an option to allow a new function mips_sram_init() being
called before setup_stack_gd.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds a new pinmux for UART2, which shares the pins with SPIS.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
SoCs of mtmips can use different CPU frequencies depending on the HW/SW
configurations. For example mt7628 uses 580MHz clock if the input xtal
frequency is 40MHz, and 575MHz clock if the xtal is 25MHz. Upon cold boot
the CPU uses the xtal frequency directly.
So hardcoding the timer frequency (half of the CPU frequency) in
CONFIG_SYS_MIPS_TIMER_FREQ is not a good idea for this case.
This patch adds a mtmips-specific field timer_freq to arch_global_data.
This field will be used later in mtmips-specific get_tbclk() to provide
accurate timer frequency in different boot stage.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch replaces sysreset-syscon with sysreset-resetctrl for mt7628 soc.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds a MIPS specific jump_to_image_no_args() implementation,
which flushes the U-Boot proper image loaded from the boot device in
SPL before jumping to it.
It has been noticed on MT76x8, that this cache flush is needed. Other
MIPS platforms might need it as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
u_boot_list is not only used by DM, but also by some SPL image load methods
such as spl_nor.c.
This patch adds an option CONFIG_SPL_LOADER_SUPPORT in conjunction with
CONFIG_SPL_DM surrounding the u_boot_list section to make sure SPL image
loaders can be correctly built into u-boot SPL without DM enabled.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
If CONFIG_SPL_OF_CONTROL is enabled for SPL and CONFIG_OF_SEPARATE is also
enabled, the dtb will be appended to the u-boot-spl.bin.
When calling dm_init_and_scan() in SPL, fdtdec_setup() will try to locate
dtb at the end of u-boot-spl.bin, by referencing to _image_binary_end.
However _image_binary_end is currently missing in u-boot-spl.lds.
This patch adds _image_binary_end to u-boot-spl.lds to make sure linking
u-boot-spl will not fail.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
When setting up initial stack, global data will also be put in the stack,
and being cleared.
The assembler instructions for clearing gd is as follows:
move t0, k0
1:
PTR_S zero, 0(t0)
blt t0, t1, 1b
PTR_ADDIU t0, PTRSIZE
t0 is the start address of gd, t1 is the end address of gd (t0 + GD_SIZE).
[PTR_ADDIU t0, PTRSIZE] is in the delay slot of [blt t0, t1, 1b], so it
will be executed before the branch operation.
However the comparison for the BLT instruction is done before executing the
delay slot. This means when the last word just before k1 is cleared, the
loop will continue to run once. This will clear an extra word at k1, which
is outside the global data.
Global data is placed at the top of the stack. If the initial stack is a
SRAM or locked cache, the area outside them may be inaccessible. A write
operation performed in this area may cause an exception.
To solve this, [PTR_ADDIU t0, PTRSIZE] should be placed before the BLT
instruction.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Both mt7620 and mt7628 has the same cache configuration. There is no need
to use CONFIG_SYS_CACHE_SIZE_AUTO to probe it at runtime.
Add them into Kconfig to reduce some code size.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
In U-Boot the exception vector base will be moved to top of memory, to be
used to display register dump when exception occurs.
But some old linux kernel does not honor the base set in CP0_EBASE. A
modified exception vector base will cause kernel crash.
This patch adds an option to enable reset exception vector base to its
previous value, or a user configured value before booting linux kernel.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Add memory-controller@e000e000 node in zynq-ces-nand.dts as
zynq_nand driver utilizes flash@e1000000 node. Without this
dt node mini nand u-boot does not probe.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- Do not use irps54012 as device node which is not correct.
- Fix addresses of irps5401/u180 on zcu104 revisions.
- Remove clock-cells property. It is PMIC without any clock output.
- Define irps5401 nodes in zynqmp-e-a2197
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As we've dropped NAND support for AXS101 and AXS103
see commit 4f5e552d95 ("ARC: AXS10x: drop NAND support")
we don't need bounce buffer anymore.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Add label to GPIO lines controlling boot mode and POR EMIO pins so System
Controller can assert those lines on Versal.
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Stack size has been introduced by commit a69814c815 ("arm64: zynqmp:
Set initrd_high to as high as possible") and commit 085201c246 ("arm64:
versal: Set initrd_high to as high as possible")
to support setting up initrd_high as high as possible.
The same change should happen for Zynq because the code is moved to xilinx
common location.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for CSM enable/disable and CSM relocation via
hsdk_init command. We allow to relocate CSM to the beginning of
any aperture even if HW support finer granularity.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Split HSDK and HSDK-4xD device tree files so they can have
different model names.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Add initial HSDK-4xD board support.
The ARC HS4x/HS4xD Development Kit includes a multicore ARC HS4xD-based
chip that integrates a wide range of interfaces including Ethernet,
HDMI, WiFi, Bluetooth, USB, SDIO, I2C, SPI, UART, I2S, ADC, PWM and
GPIO, as well as a Think Silicon GPU.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
In case of DSP extension presence in HW some instructions
(related to integer multiply, multiply-accumulate, and divide
operation) executes on this DSP execution unit. So their
execution will depend on dsp configuration register (DSP_CTRL)
As we want these instructions to execute the same way regardless
of DSP presence we need to set DSP_CTRL properly.
NOTE:
we do the same adjustments in Linux kernel, see in kernel tree:
commit 4827d0cf744e ("ARC: handle DSP presence in HW")
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Offset value for CLKMGR_S10_PERPLL_BYPASS should be 0xb0, fix it.
Reported-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
The Cubieboard is a single board computer containing a
Actions S700 SoC(with 4 ARMv8 Cortex-A53 cores).
This patch adds respective defconfig alongwith .dts(copied
from Linux v5.5-rc6 with hash "b3a987b0264d").
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This patch moves some of the config options from bubblegum_96_defconfig
to respective Kconfig files.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This patch adds basic support for Actions Semi based S700
SoC, which is driven by common owl framework.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Devices like uart and clk are needed to be enabled before relocation.
this patch adds u-boot.dtsi file that mark these device as dm-pre-reloc.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This patch adds .dtsi file(sync with Linux 5.5-rc6 with hash "b3a987b0264d")
and required binding for S700 SoC that is a 64-bit Quad-core ARM
Cortex-A53 cores.
It also provisions dts file to be built based on selected
platform(CONFIG_MACH_S900/S700).
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This patch converts S900 clock driver to something common that can
be used for other SoCs, for instance S700(few of clk registers are same).
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Devices like uart and clk are needed to be enabled before relocation.
This patch adds u-boot.dtsi file that mark these device as dm-pre-reloc.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Synchronize device tree bindings with v5.5-rc6 tag with commit id
"b3a987b0264d".
Also, it removes older clock binding defined for S900 along with undocumented
compatible string "actions,s900-serial" from serial driver and adapts clock
driver to cater to new bindings.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Now that memory maps(for both S700 and S900 SoCs) can be managed using
a common file, rename sysmap-s900 to sysmap-owl to reflect the same.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This commit adds common arch support for Actions Semi Owl
series SoCs and removes the Bubblegum96 board files.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Introduce arch_reserve_mmu to allow for architecture-specific reserve_mmu
routines. Also, define a weak nop stub for it.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As a preparation for turning reserve_mmu into an arch-specific variant,
introduce arm_reserve_mmu on ARM. It implements the default routine for
reserving memory for MMU TLB and needs to be weakly defined in order to allow
for machines to override it.
Without this decoupling, after introducing arch_reserve_mmu, there would be two
weak definitions for it, one in common/board_f.c and one in
arch/arm/lib/cache.c.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the ARM-specific reserve_mmu definition from common/board_f.c
to arch/arm/lib/cache.c.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Split device tree for DHCOR Som and AV 96 board
- Update PLL4 setting in AV96 board
- Enable bootd, iminfo, imxtract on DHCOM
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl6jDmEACgkQ4rK92eCq
k3XwXQgAhCsdAF8qBa6qFqHY2APmfm1a3SLHUqEMEAh1y0R8bg3nSon3xDolGONB
9AIv4PVNjQyvG+8uJrdj/SLC1dKEYI1uU8gUPVau/V9yOR3purSa0RYg4gDRcs3T
8vwgGfp9kMwygOOVWdvd1YFnrDrtDF9OiF7i5ei7RhHRvMTThNa2Y1zeKI2z9svZ
XRNoED1/2G/ms4VOiRoxp5HhNH7akvG8VsZF9PhjEqsXtJoQ8uv7AMLOscnZHmh9
hol9voBValanfg3K2Hafubyq00ori51EvbhRJ10jDkXXkjgOflcHCVWIj4Ihq3oI
cQmUZ6eErS4uDYP4s7xvjE88Uxn0XA==
=uKKC
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200424' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Solve stm32mp15 pinctrl dts issue (patch conflict in branches master and next)
- Split device tree for DHCOR Som and AV 96 board
- Update PLL4 setting in AV96 board
- Enable bootd, iminfo, imxtract on DHCOM
