Add register definitions for the i.MX23 power control block and
clock control block. These are essential for the basic bootstrap
of the i.MX23. Also, properly include them in imx-regs.h .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
This has been copied from Linux source at revision 786f02b719f.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
This adds the base addresses of i.MX23 and easy the detection of wrong
order in board setup, in case no SoC has been set, an error is raised
during build.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Create function which converts SSP bus number to SSP register pointer.
This functionality is reimplemented multiple times in the code, thus
make one common implementation. Moreover, make it a switch(), since the
SSP ports are not mapped in such nice linear fashion on MX23, therefore
having it a switch will simplify things there.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Add apbdma node for tegra20 and tegra30, copied directly from tegra
Linux dtsi files.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Sort nodes in dts files according the the following rules:
1) Any nodes that already exist in any /include/d file, in the order
they appear in the /include/d file.
2) Any nodes with a reg property, in order of their address.
3) Any nodes without a reg property, alphabetically by node name.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
IRDA is a synonym for UARTB in tegra pinmux, remove all usage of this
synonym and replace with UARTB to disambiguate.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Note that T30 does not have a separate/different DVC (power I2C)
controller like T20 - all 5 I2C controllers are identical, but
DVC_I2C is still used to designate the controller intended for
power control (PWR_I2C in the schematics). On Cardhu, it's used
to access the PMU and EEPROM, as well as the audio codec, temp
sensor, and fuel gauge devices from the OS.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add 16-bit divider support (I2C) to periph table, annotate and
correct some entries, and fix clk_id lookup function.
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch adds basic Tegra30 (T30) build support - no specific
board is targeted.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
These are stripped down for bringup, They'll be filled out later
to match-up with the kernel DT contents, and/or as devices are
brought up (mmc, usb, spi, etc.).
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
These files are used by both SPL and main U-Boot.
Also made minor changes to shared Tegra code to support
T30 differences.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
These files are for code that runs on the CPU (A9) on T30 boards.
At this time, there are no T30-specific ARMV7 files. As T30-specific
run-time code is added, it'll go here.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidai.com>
This provides SPL support for T30 boards - AVP early init, plus
CPU (A9) init/jump to main U-Boot.
Some changes were made to Tegra20 cpu.c to move common routines
into tegra-common/cpu.c and reduce code duplication.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Common Tegra files are in arch-tegra, shared between T20 and T30.
Tegra30-specific headers are in arch-tegra30. Note that some of
these will be filled in as more T30 support is added (drivers,
WB/LP0 support, etc.). A couple of Tegra20 files were changed
to support common headers in arch-tegra, also.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Boards may require a different pinmux setup for DISPALY than the default one.
Add a way to call into board specific code to set this up.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
When u-boot is compiled for PXA25x processor, pxa/start.S is calling
cpu_init_crit by BL instruction. BL is overwriting lr register so
relocate_code is going into infinite loop. This patch preservs lr
register in r12 before calling cpu_init_crit and after function returns
restores it.
Signed-off-by: Lukasz Dalek <luk0104@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Mobile storage is used the CLK_DIV_FSYS3 value.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
To get exactly clock value for mmc, support the get_mmc_clk() like
set_mmc_clk().
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The two modified lines were indented with spaces.
They are now indented with tabs.
Signed-off-by: Taylor Hutt <thutt@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The timer may be inited in arch_cpu_init() so it is not safe to make a
bootstage mark before this is called. Arrange the code to fix this.
Note: The question was raised as to why we don't keep all archs in sync.
PowerPC doesn't have specific bootstage markers at present (although it
does use boot progress). I hope that the generic board series will solve
this problem in general, but in the meantime this is a real problem, and
only in ARM.
We now get a correct time for board_init_f:
Timer summary in microseconds:
Mark Elapsed Stage
0 0 reset
100,000 100,000 spl_start
848,530 748,530 board_init_f
907,301 58,771 board_init_r
910,478 3,177 board_init
Signed-off-by: Simon Glass <sjg@chromium.org>
SPL u-boot may call do_reset() which depends on interrupts.o and reset.o.
So make them also appear in SPL.
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This option displays board info after stdio is running, so that it will
appear on the LCD. If it is displayed earlier, the board info will appear
on the serial console but not on the LCD.
Here follows a blow-by-blow description.
1a. Without CONFIG_DISPLAY_BOARDINFO_LATE, on serial:
U-Boot 2011.12-02550-g037e1c5-dirty (Nov 15 2012 - 14:29:42) for SMDK5250
CPU: S5PC520 @ 1700MHz
Board: Google Snow, rev 0
I2C: ready
DRAM: 2 GiB Elpida DDR3 @ 800MHz
MMC: S5P MSHC0: 0, S5P MSHC1: 1
SF: Detected W25Q32 with page size 4 KiB, total 4 MiB
*** Warning - bad CRC, using default environment
In: mkbp-keyb
Out: lcd
Err: lcd
Net: No ethernet found.
Hit any key to stop autoboot: 0
SMDK5250 #
1b. Without CONFIG_DISPLAY_BOARDINFO_LATE, on LCD (note machine info
is missing):
In: mkbp-keyb
Out: lcd
Err: lcd
Net: No ethernet found.
Hit any key to stop autoboot: 0
SMDK5250 #
2a. With CONFIG_DISPLAY_BOARDINFO_LATE, on serial:
U-Boot 2011.12-02550-g037e1c5 (Nov 15 2012 - 14:27:40) for SMDK5250
CPU: S5PC520 @ 1700MHz
I2C: ready
DRAM: 2 GiB Elpida DDR3 @ 800MHz
MMC: S5P MSHC0: 0, S5P MSHC1: 1
SF: Detected W25Q32 with page size 4 KiB, total 4 MiB
*** Warning - bad CRC, using default environment
Model: Google Snow
In: mkbp-keyb
Out: lcd
Err: lcd
Net: No ethernet found.
Hit any key to stop autoboot: 0
SMDK5250 #
2b. With CONFIG_DISPLAY_BOARDINFO_LATE, on LCD (note machine info is present):
Model: Google Snow
In: mkbp-keyb
Out: lcd
Err: lcd
Net: No ethernet found.
Hit any key to stop autoboot: 0
SMDK5250 #
Since the LCD is all that a typical user sees, it is useful to display
the model there.
We may be able to rearrange things some other way one day, but at
present this seems like a convenient way of getting the required
behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
This option delays loading of the environment until later, so that only the
default environment will be available to U-Boot.
This can address the security risk of untrusted data being used during boot.
Any time you load untrusted data you expose yourself to a bug in the
code. The attacker gets to choose the data so can sometimes carefully
craft it to exploit a bug. We try to avoid touching user-controlled
data during a verified boot unless strictly necessary. Since the
default environment is good enough in this case (or you would just
change it), this gets around the problem by just not loading the
environment.
When CONFIG_DELAY_ENVIRONMENT is defined, it is convenient to have a
run-time way of enabling loading of the environment. Add this to the
fdt as /config/delay-environment.
Note: This patch depends on http://patchwork.ozlabs.org/patch/194342/
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
We want to use the fdt inside board_early_init_f(), so check for its
presence earlier in the pre-reloc init sequence.
So far ARM and microblaze are the only only ones that use
CONFIG_OF_CONTROL. Microblaze does not have the same init loop, and in
particular does not have the board_early_init_f() call. So a patch for
microblaze would have no meaning.
Signed-off-by: Simon Glass <sjg@chromium.org>
It may be necessary to know where the TLB area ends as well as where it
starts. This allows board code to complete a secure memory erase without
destroying the page tables.
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
In Cortex-A15 architecture, when we run cache invalidate
the cache clean operation executes automatically.
So if there are any dirty cache lines before disabling the L2 cache
these will be synchronized with the main memory when
invalidate_dcache_all() runs in the last part of U-boot
The two functions after flush_dcache_all is using the stack. So this
data will be on the cache. After disable when invalidate is called the
data will be flushed from cache to memory. This corrupts the stack in
invalida_dcache_all. So this change is required to avoid the u-boot
hang.
So flush has to be done just before clearing CR_C bit
Signed-off-by: Arun Mankuzhi <arun.m@samsung.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
When only DP is used, we need not enable CONFIG_EXYNOS_MIPI_DSIM.
But if we do not select CONFIG_EXYNOS_MIPI_DSIM, exynos_fb.c throws
error saying exynos_mipi_dsi_init() not defined. So, we add
dummy definition for exynos_mipi_dsi_init when CONFIG_EXYNOS_MIPI_DSIM
is not defined.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
With VPLL as source clock to FIMD,
Exynos DP Initializaton was failing sometimes with unstable clock.
Changing FIMD source to MPLL resolves this issue.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add panel_info structure required by LCD driver
and DP panel platdata for SMDK5250.
Add GPIO configuration for LCD.
Enable FIMD and DP support on SMDK5250.
DP Panel size: 2560x1600.
We use 16BPP resolution to get LCD console.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chomium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add workaround for the following ARM errata: 743622 and 751472.
The motivation for this change is the following kernel commit 62e4d357a
(ARM: 7609/1: disable errata work-arounds which access
secure registers), which removes the errata from multiplatform kernel.
Since imx has been converted to multiplatform in the kernel, we need to apply
such workarounds into the bootloader.
Workaround code has been taken from arch/arm/mm/proc-v7.S from 3.7.1 kernel.
Explanation of each erratum is provided at "Chip Errata for the i.MX 6Dual/6Quad"
document available at: cache.freescale.com/files/32bit/doc/errata/IMX6DQCE.pdf
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Modified the arch-kirkwood header so KWGBE_PORT_SERIAL_CONTROL1_REG(x)
returns the correct address.
Originally calling KWGBE_PORT_SERIAL_CONTROL1_REG(1) returned the
address for port 0 and vice versa.
Doesn't have any knock on effects to the u-boot code as the only
time they're used is to do the same function to both addresses
Signed-off-by: Luke Lowrey <luke@chamsys.co.uk>
Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
Acked-by: Heiko Schocher <hs@denx.de>
This saves stack and code memory for local copy, and
consumes initialized data memory. For 22 of the 29
kirkwood-based boards, this results in a global saving
of about 30 bytes. For 7 of them, it results in an
increase of 6 to 14 bytes.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Move all the C runtime setup code from every start.S
in arch/arm into arch/arm/lib/crt0.S. This covers
the code sequence from setting up the initial stack
to calling into board_init_r().
Also, rewrite the C runtime setup and make functions
board_init_*() and relocate_code() behave according to
normal C semantics (no jumping across the C stack any
more, etc).
Some SPL targets had to be touched because they use
start.S explicitly or for some reason; the relevant
maintainers and custodians are cc:ed.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This patch adds the device node required for USB
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add SPI device node data for exynos.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add sound device node data for exynos
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Api is added to decode peripheral id based on the interrupt number
of the peripheral.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add I2C device node data for exynos
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch add pinmux settings for Exynos4 for mmc0 and mmc2
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adds functions to extract clock frequency of Exynos4x12 IPs.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add device tree based ethernet driver for SMC911X controller on
SMDK5250 boards.
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds initial dts file for EXYNOS5250 SoC. This dts
file currently include only ethernet devices and properties. More
devices to be added in subsequent patches.
Also add the dts file for SMDK5250 board which uses the EXYNOS5250
dts file.
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds gpio structure for Exynos4x12.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds clock structure for Exynos4x12.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch populates base addresses of Exynos4x12 registers.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This commit merges branches from samsung, imx and tegra
meant to fix merge issues between u-boot/master and
u-boot-arm/master, as well as a few manual merge fixes.
Move the getenv_yesno() to env_common.c and change most checks for
'y' or 'n' to use this helper.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
This patch add pinmux for I2C for Exynos4
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
This patch add the spacing for i2c for Exynos4
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
This patch adds i2c clock for Exynos4
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
This algorithm computes the values of TIMING{0,1,2} registers for the
MX28 I2C block. This algorithm was derived by using a scope, but the
result seems correct.
The resulting values programmed into the registers do not correlate
with the contents in datasheet. When using the values from the datasheet,
the I2C clock were completely wrong.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
The reset procedure works on watchdog timer while before it was modifying
TIMER_1 registers.
Tested on DM365.
Signed-off-by: Davide Bonfanti <davide.bonfanti@bticino.it>
DMM_LISA_MAP registers program whether memory is mapped
on particular EMIF or not. Irrespective of these registers
EMIF is getting configured. Correcting the same.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Git commit d417d1db5f replaced the
omap-common file reset.S with reset.c, but the Makefile was not
adjusted for that.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
No functional changes, just more comments for readability when a
preprocessor check spans more than a few lines, and for consistency.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Instead of passing individual registers by value to board_get_mem_timings,
pass a board_mem_timings structure pointer for the board files to fill in.
Pass same structure pointer to write_sdrc_timings. This saves about
90 bytes of space in SPL.
Signed-off-by: Peter Barada <peter.barada@logicpd.com>
AM33XX has Error Location Module (ELM) that can be used in conjuction
with GPMC controller to implement BCH codes fully in hardware.
This code is mostly taken from arago tree.
Signed-off-by: Mansoor Ahamed <mansoor.ahamed@ti.com>
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
TI AM33XX has the same GPMC controller as OMAP3 so we could just use the
existing omap_gpmc driver. This patch adds adds required
definitions/intialization.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Include asm/arch/sys_proto.h for gpmc_init prototype.
Without this we get a warning while building for AM335x.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
These GPMC_CS defines are a leftover from prior gpmc_init(). Commit 187af954
removed the need for these definitions but missed to remove them.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Conflicts:
drivers/power/power_fsl.c
include/configs/mx35pdk.h
include/configs/mx53loco.h
include/configs/woodburn_common.h
board/woodburn/woodburn.c
These boards still use the old old PMIC framework, so they
do not merge properly after the power framework was merged into
mainline.
Fix all conflicts and update woodburn to use Power Framework.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Use a generic 'dram_vals[]' array that has the full initialization
sequence and rename the initialization method so it doesn't has a
frequency on its name.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The MXS SPL didn't mark local functions "static". Fix it. This also makes the
SPL smaller by roughly 300 bytes.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
The memory setup code adjusted the VDDD voltage. Remove this adjustment
and configure the VDDD voltage correctly in the power supply setup code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Implement common function to setup the VDDIO, VDDD and VDDA voltage.
Right now, there are two almost identical functions to setup VDDIO
and VDDD, which is prone to breakage. Pull out the differences into
constant structure and pass them as an argument to the common function.
Moreover, the function has almost identical loops for setting higher
and lower VDDx voltage. Merge these two loops.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
The i.MX23 has different register layout and bit placement in the
power supply. Thus, in order to be able to add support for MX23,
rename the MX28's regs-power.h to regs-power-mx28.h . Moreover,
add ifdef around inclusion of regs-*-mx28.h in imx-regs.h so the
MX23 boards will include proper set of registers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
These registers don't have _SET, _CLR and _TOG at the respective offsets
available, these registers has to be toggled via R-M-W if needed. Thus do
not export these offsets anymore.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
The POWER_DCLIMITS_NEGLIMIT_OFFSET bit in mx28 power supply block is
not called POWER_DCLIMITS_NETLIMIT_OFFSET, but POWER_DCLIMITS_NEGLIMIT_OFFSET.
Correct the name in the header file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The POWER_MINPWR_VBG_OFF bit in mx28 power supply block is not called
POWER_MINPWR_FBG_OFF, but POWER_MINPWR_VBG_OFF. Correct the name in the
header file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Backend driver for MUSB OTG controllers found on TI AM35x.
It seems that on AM35X interrupt status registers can be updated
_before_ core registers. As we don't use true interrupts in U-Boot
and poll interrupt status registers instead this can result in
interrupt handler being called with non-updated core registers.
This confuses the code and result in hanged transfers.
Add a small delay in am35x_interrupt as a workaround.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
AM33xx has support for dual port MUSB OTG controller. This patch
adds initialization for the controller using new MUSB gadget
driver and ether gadget.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Backend driver for MUSB OTG controllers found on TI AM33xx and
TI81xx SoCs (tested with AM33xx only).
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Add support for adjusting the L1 cache behavior by updating the MMU
configuration. The mmu_set_region_dcache_behaviour() function allows
drivers to make these changes after the MMU is set up.
It is implemented only for ARMv7 at present.
This is needed for LCD support, where we want to make the LCD frame buffer
write-through (or off) rather than write-back.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add support for the LCD peripheral at the Tegra2 SOC level. A separate
LCD driver will use this functionality to configure the display.
Signed-off-by: Mayuresh Kulkarni <mkulkarni@nvidia.com>
Mayuresh Kulkarni:
- changes to remove bitfields and clean up for submission
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass:
- simplify code, move clock control into here, clean-up
Signed-off-by: Tom Warren <twarren@nvidia.com>
The pulse width/frequency modulation peripheral supports generating
a repeating pulse. It is useful for controlling LCD brightness.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add LCD definitions and also a proposed binding for LCD displays.
The PWM is as per what will likely be committed to linux-next soon.
The displaymode binding comes from a proposal here:
http://lists.freedesktop.org/archives/dri-devel/2012-July/024875.html
The panel binding is new, and fills a need to specify the panel
timings and other tegra-specific information. Should a binding appear
that allows the pwm to handle this automatically, we can revisit
this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This binding will apparently soon be in linux-next. Bring it in now
since we need to do something, and may as well try to target what
Linux will have.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
These two functions don't actually modify their arguments so add a const
keyword.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The mx5 lowlevel_init.S contains board-specific code based on the reference
design. Let's keep it since it avoids creating new lowlevel_init files and it
may be used by many boards. But add a config to make it optional in order not to
cause issues on boards not following this part of the reference design.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matt Sealey <matt@genesi-usa.com>
Acked-by: Stefano Babic <sbabic@denx.de>
If a board does not enable CSPI, there is no need to show the CSPI clock
frequency as part of the 'clock' command.
Reported-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Some MXC SoCs like the i.MX35 have hosts located at unusual offsets, so prepare
to the introduction of i.MX35 support by defining the ehci-mxc hosts offsets at
SoC level.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The EHCI definitions in i.MX31's imx-regs.h are MXC-generic, so move them to
ehci-fsl.h so that all MXC SoCs can use them.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
This patch adds SPI driver for EXYNOS.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: jy0922.shim@samsung.com
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add base address definition for SPI device on Exynos.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add api to calculate and set the clock for SPI channels
Signed-off-by: James Miller <jamesmiller@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds pinmux support for SPI channels
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds clock support for I2S
Signed-off-by: R. Chandrasekar <rcsekar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds base address for I2S
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Chander Kashyap <chander.kashyap@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds pinmux support for I2S1
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds the audio parameters required by the I2S to play the
predefined audio data.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
arch_cpu_init() is removed from cpu level to SOC level for arm1176
in commit 4ea6d6b,the same is done for s3c64xx
Signed-off-by: Ashok Kumar Reddy <ashokkourla2000@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David Müller <d.mueller@elsoft.ch>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Moved the common code to calculate pll clock rate to new function
exynos_get_pll_clk().
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Based upon single SoC there can be multiple variants.
This patch add support to match the complete product ID.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
This patch add pinmux settings for Exynos4 for mmc0 and mmc2
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Now proper GPIO parts numbering is handled at Samsung devices.
This fix is necessary for code using GPIO located at other banks
than first.
Test HW:
- Exynos4210 - Trats
- S5PC110 - goni
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The inclusion of LCD patch into mx51evk breaks the build when
CONFIG_VIDEO is disabled. Fix this by splitting the video related
stuff to a new file.
Also rename the function lcd_iomux to setup_iomux_lcd to make the
namings aligned with the other iomux functions.
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
It is necessary to introduce a new system wide function- power_init_board()
It turns out, that power initialization must be done as early as possible.
In the case of PMIC framework redesign, which aims to support multiple
instances of PMIC devices the initialization shall be performed just
after malloc configuration.
The power_init_board function is a weak function with default implementation.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
enable_caches() did not enable icache if CONFIG_SYS_ICACHE_OFF was not defined
but CONFIG_SYS_DCACHE_OFF was.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Only the values used in the sabrelite board are
added currently. Add more as other boards use them.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Read memory setup registers to determine size
of available ram. This routine works for mx53/mx6x
I need this because when mx6solo called get_ram_size
with a too large maximum size, the system hanged.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Previously, the same value was returned for both mx6dl and mx6solo.
Check number of processors to differeniate.
Also, a freescale patch says that sololite has its cpu/rev
stored at 0x280 instead of 0x260.
I don't have a sololite to verify.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
u-boot's byteorder headers did not contain endianness attributions
for use with sparse, causing a lot of false positives. Import the
kernel's latest definitions, and enable them by including compiler.h
and types.h. They come with 'const' added for some swab functions, so
fix those up, too:
include/linux/byteorder/big_endian.h:46:2: warning: passing argument 1 of '__swab64p' discards 'const' qualifier from pointer target type [enabled by default]
Also, note: u-boot's historic __BYTE_ORDER definition has been
preserved (for the time being at least).
We also remove ad-hoc barrier() definitions, since we're including
compiler.h in files that hadn't in the past:
macb.c:54:0: warning: "barrier" redefined [enabled by default]
In addition, including compiler.h in byteorder changes the 'noinline'
definition to expand to __attribute__((noinline)). This fixes
arch/powerpc/lib/bootm.c:
bootm.c:329:16: error: attribute '__attribute__': unknown attribute
bootm.c:329:16: error: expected ')' before '__attribute__'
bootm.c:329:25: error: expected identifier or '(' before ')' token
powerpc sparse builds yield:
include/common.h:356:22: error: marked inline, but without a definition
the unknown-reason inlining without a definition is considered obsolete
given it was part of the 2002 initial commit, and no arm version was
'fixed.'
also fixed:
ydirectenv.h:60:0: warning: "inline" redefined [enabled by default]
and:
Configuring for devconcenter - Board: intip, Options: DEVCONCENTER
make[1]: *** [4xx_ibm_ddr2_autocalib.o] Error 1
make: *** [arch/powerpc/cpu/ppc4xx/libppc4xx.o] Error 2
powerpc-fsl-linux-size: './u-boot': No such file
4xx_ibm_ddr2_autocalib.c: In function 'DQS_autocalibration':
include/asm/ppc4xx-sdram.h:1407:13: sorry, unimplemented: inlining failed in call to 'ppc4xx_ibm_ddr2_register_dump': function body not available
4xx_ibm_ddr2_autocalib.c:1243:32: sorry, unimplemented: called from here
and:
In file included from crc32.c:50:0:
crc32table.h:4:1: warning: implicit declaration of function '___constant_swab32' [-Wimplicit-function-declaration]
crc32table.h:4:1: error: initializer element is not constant
crc32table.h:4:1: error: (near initialization for 'crc32table_le[0]')
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
[trini: Remove '#endif' in include/common.h around setenv portion]
Signed-off-by: Tom Rini <trini@ti.com>
Timer is initialized already in board_init_r function in
(common/spl/spl.c) No need to initialize it again
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
When CONFIG_SYS_L2CACHE_OFF is defined we end up with a few warnings
currently. Re-order functions so that we don't have that anymore.
Signed-off-by: Tom Rini <trini@ti.com>
Add back common.h header that was removed in previous patch so that
CONFIG_TEGRA can be evaluated correctly.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Initialize this variable to avoid a compiler warning about possible
use of uninitialized variable with gcc 4.4.6.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Change tegra SPL to use common SPL framework. Any tegra specific
initialization is now done in spl_board_init() instead of
board_init_f()/board_init_r(). Only one SPL boot target is supported
on tegra, which is boot to RAM image. jump_to_image_no_args() must be
overridden on tegra so the host CPU can be initialized.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add an ASSERT() to u-boot.lds to detect an SPL that doesn't fit within
SPL_TEXT_BASE..SPL_MAX_SIZE.
Different .lds files implement this check in two possible ways:
1) An ASSERT() like this
2) Defining a MEMORY region of size SPL_MAX_SIZE, and re-directing all
linker output into that region. Since u-boot.lds is used for both
SPL and main U-Boot, this would entail only sometimes defining a
MEMORY region, and only sometimes performing that redirection, and
hence option (1) was deemed much simpler, and hence implemented.
Note that this causes build failures at least for NVIDIA Tegra Seaboard
and Ventana. However, these are legitimate; the SPL doesn't fit within
the required space, and this does cause runtime issues.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Allen Martin <amartin@nvidia.com>
Acked-by: Tom Rini <trini@ti.com>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
When -ffunction-sections or -fdata-section are used, symbols are placed
into sections such as .data.eserial1_device and .bss.serial_current.
Update the linker script to explicitly include these. Without this
change (at least with my gcc-4.5.3 built using crosstool-ng), I see that
the sections do end up being included, but __bss_end__ gets set to the
same value as __bss_start.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Allen Martin <amartin@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
imx-regs.h is meant to contain SoC register definitions.
Common SoC funtions should go to sys_proto.h instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The woodburn board is based on the MX35 SOC.
Support for both external (NOR) and internal
(SD Card) boot mode are added. It uses the
generic SPL framework to implement the internal boot
mode.
The following peripherals are supported:
- Ethernet (FEC)
- SD Card
- NAND (512 MB)
- NOR Flash
In the internal boot mode, a simple imximage header
is generated to set the address in internal RAM
where the SOC must copy the SPL code. The initial setup
is then demanded to the SPL itself.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The patch adds SPL for the arm1136 architecture and
inserts SPL (the produced binary) to clobber target
in the main Makefile.
Signed-off-by: Stefano Babic <sbabic@denx.de>
This patch modifies start.S for the arm1136 to make it
conform to start.S in armv7 architecture, to make it
usable if the SPL framework is used.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Patch fix warnings compiling with ELDK-4.2:
clock.c: In function 'get_standard_pll_sel_clk':
clock.c:341: warning: 'freq' may be used uninitialized in this function
Reported-by : Marek Vasut <marex@denx.de>
Signed-off-by: Stefano Babic <sbabic@denx.de>
If configured to use UART{1,2,3,4,5} such as on the Beaglebone RS232
cape or the am335x_evm daughterboard, enable the required clocks for
the UART in use.
Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
Move the hardcoded ddr2/ddr3 settings for the ti boards to board code,
so other boards can use different types/timings.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Make apply with rtc32k_enable() in the file]
Signed-off-by: Tom Rini <trini@ti.com>
The i2c header is specific to ti(-derived) boards, and not generic for all
am335x boards.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Make re-apply with rtc32k_enable() applied]
Signed-off-by: Tom Rini <trini@ti.com>
Add the required config.mk logic for this SoC as well as the BOOT_DEVICE
define. Finally, enable the options on the am335x_evm.
Signed-off-by: Tom Rini <trini@ti.com>
In order to support low power state, you must source kernel system
timers to persistent clock, available across suspend/resume. In case of
AM335x device, the only source we have is, RTC32K, available in
wakeup/always-on domain. Having said that, during validation it has
been observed that, RTC clock need couple of seconds delay to stabilize
the RTC OSC clock; and such a huge delay is not acceptable in kernel
especially during early init and also it will impact quick/fast boot
use-cases.
So, RTC32k OSC enable dependency has been shifted to
SPL/first-bootloader.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
DDR3 support is tested and working with beaglebone hardware. Include a check
for this board type and configure DDR3. The timings and other configuration
match EVM SK.
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Acked-by: Jason Kridner <jdk@ti.com>
The command declaration now uses the new LG-array method to generate
list of commands. Thus the __u_boot_cmd section is now superseded and
redundant and therefore can be removed. Also, remove externed symbols
associated with this section from include/command.h .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
This patch converts the old method of creating a list of command
onto the new LG-arrays code. The old u_boot_cmd section is converted
to new u_boot_list_cmd subsection and LG-array macros used as needed.
Minor adjustments had to be made to the common code to work with the
LG-array macros, mostly the fixup_cmdtable() calls are now passed the
ll_entry_start and ll_entry_count instead of linker-generated symbols.
The command.c had to be adjusted as well so it would use the newly
introduced LG-array API instead of directly using linker-generated
symbols.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Add section for the linker-generated lists into all possible linker
files, so that everyone can easily use these lists. This is mostly
a mechanical adjustment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
This does not need to be a long, so change it.
Also adjust bi_baudrate to be unsigned.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@ti.com>
Rather than leave the fdt down next to the code/data, we really should
relocate it along with everything else. For CONFIG_OF_EMBED this happens
automatically, but for CONFIG_OF_SEPARATE it does not.
Add code to copy the fdt and point to the new copy after relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David Müller <d.mueller@elsoft.ch>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Oliver Brown <obrown@adventnetworks.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Add the software workaround for ARM erratum ID 468414.
According to mx53/mx51 errata document:
"ENGcm11133 - ARM: NEON load data can be incorrectly forwarded to a
subsequent request
Description:
Under very specific set of conditions, data from a Neon load request can be incorrectly forwarded
to a subsequent, unrelated memory request.
The conditions are as follows:
• Neon loads and stores must be in use
• Neon L1 caching must be disabled
• Trustzone must be configured and in use
• The secure memory address space and the non-secure memory address space both use the same
physical addresses, either as an alias or the same memory location or for separate memory
locations
The issue is reported by ARM, erratum ID 468414, Category 2"
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Currently PLL2 is not explicitely configured for mx53 and it runs at 333MHz.
Since PLL2 is the parent clock for DDR2, IPU, VPU, we should set it at 400MHz
instead.
Without doing so, it is not possible to use a 2.6.35 FSL kernel and display HDMI
at 1080p because the IPU clock cannot reach the requested frequency.
Set PLL2 to 400MHz, so that 1080p can be played and the DDR2 can run at its
maximum frequency.
Also, setup the other PLL's as done in FSL U-boot and re-arrange the code a little
bit to allow easier comparison with the original clock setup from FSL U-boot.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
init_clock is currently shared between mx51 and mx53 and it contains lots of
ifdef's which makes it really hard to follow the code.
Split the init_clock between mx51 and mx53 to allow easier readability.
No functional changes are made.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Since commit 957731ed (ARM: remove broken "lpd7a40x" boards),
lh7a40x cpu and serial driver have become unused. Remove them.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
The kernel from Freescale expects that the bootloader passes the board revision.
Read the board revision and pass it via get_board_rev().
Without passing the board revision the kernel does not operate properly as the
initialization of peripherals are different in revA versus revB boards.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Each eSDHC instance has a dedicated clock.
gd->sdhc_clk must also be set accordingly. This is good for the case only a
single SDHC instance is used (initialization made with fsl_esdhc_mmc_init()). A
future patch will fix the multi-instance use case (initialization made directly
with fsl_esdhc_initialize()).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Clean up mx35 lowlevel_init:
- Indent with tabs.
- Fix comments.
- Use defined values instead of literal constants.
- Use defined macros instead of duplicating code.
- Use macro parameters with default values instead of #define'd configs.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Clean up mx25 lowlevel_init:
- Add comments.
- Do not use write32 repeatedly with the same value in order not to increase
code size.
- Make register values configurable.
- Use macro parameters with default values instead of literal constants.
- Use defined macros instead of duplicating code.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
Cc: Matthias Weisser <weisserm@arcor.de>
The CSI PODF bit-field used by the previous code for the i.MX31 CCM PDR0
register is actually composed of two bit-fields: one pre-divider and one
post-divider. This patch fixes the CCM access macros and the code using them
accordingly.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Optimize mx5 lowlevel_init.S code size:
- Compute values at compile time rather than at runtime where possible.
- Assign r4 to hold the zero value rather than setting registers to 0 again and
again.
- Associate a function to setup_pll rather than expanding its large macro code
multiple times.
- Allocate constant values in section only if used.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
The MMC driver appropriate for the i.MX25 is fsl_esdhc, which has nothing to do
with mxcmmc.
Also, each eSDHC instance has a dedicated clock, so gd->sdhc_clk must be set
accordingly. This is good for the case only a single SDHC instance is used
(initialization made with fsl_esdhc_mmc_init()). A future patch will fix the
multi-instance use case (initialization made directly with
fsl_esdhc_initialize()).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
The FEC is the only SoC Ethernet support available on i.MX25, so define
cpu_eth_init() only for it instead of returning a misleading success code.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Use the standard mxc_get_clock() instead of exporting internal functions and
using literal constant values.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
mxc_get_clock(MXC_FEC_CLK) should return the IPG clock, not the AHB clock.
Also, imx_get_fecclk() was correct but reimplemented the calculation of the IPG
clock, so remove the duplicated code.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Avoid possible overflow in clock calculations, and do not waste calls to lldiv()
to divide simple ulongs.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
The MFN bit-field of the PLL registers represents a signed value. See the
reference manual.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
The i.MX5 eSDHC clocks were considered as coming from the IPG clock although
they have dedicated clock paths.
Also, on i.MX5/6, each SDHC instance has a dedicated clock, so gd->sdhc_clk must
be set accordingly. This is good for the case only a single SDHC instance is
used (initialization made with fsl_esdhc_mmc_init()). A future patch will fix
the multi-instance use case (initialization made directly with
fsl_esdhc_initialize()).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
There are only 2 I²C instances on i.MX51, but 3 on i.MX53.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
The FEC clock does not come from PLL1, but from the IPG clock. The previous code
was even inconsistent with itself, returning the IPG clock as expected for
imx_get_fecclk(), but the PLL1 clock for mxc_get_clock(MXC_FEC_CLK).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
The code handling the dividers was duplicated for each possible input clock, and
this function can benefit from the newly introduced get_standard_pll_sel_clk()
function instead of duplicating this mux handling code.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
This function returned 66500000 instead of the correct lp_apm clock frequency if
the CCM.CSCMR1.uart_clk_sel mux is set to 3.
This patch fixes this issue by introducing the get_standard_pll_sel_clk()
function that will be used by future patches to handle identical muxes used by
many other clocks.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
This fixes the "IPG PERCLK" frequency printed by the clocks command. The issue
was that get_ipg_per_clk() used periph_clk instead of lp_apm in the case
CCM.CBCMR.perclk_lp_apm_sel is set.
It also fixes I²C support.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
In the case periph_clk comes from periph_apm_clk, the latter is selected by the
CCM.CBCMR.periph_apm_sel mux, which can source the lp_apm clock from its
input ♯2. get_periph_clk() returned 0 instead of the lp_apm clock frequency in
this case.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
If CCM.CCSR.lp_apm is set, the lp_apm clock is not necessarily 32768 Hz x 1024.
In that case:
- on i.MX51, this clock comes from the output of the FPM,
- on i.MX53, this clock comes from the output of PLL4.
This patch fixes the code accordingly.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
This fixes config_pll_clk(), which used 0x20 instead of 0x200 for PLL4_CLOCK.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
The i.MX51 has a single USB PHY clock, while the i.MX53 has two. These 3 clocks
have different clock gate control bit-fields.
The existing code was correct only for i.MX53, so this patch fixes the i.MX51
use case.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Jana Rapava <fermata7@gmail.com>
Cc: Wolfgang Grandegger <wg@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
The clock gate values are 2-bit bit-fields. Hence, setting or clearing only one
of these bits like what was done is wrong and can lead to unpredictable behavior
depending on the original value of these bit-fields.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Use clock gate definitions having names showing clearly the gated clock instead
of names giving only a register field index.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Clean up the i.MX5 clock driver:
- Use readl() and writel() instead of their __raw_ counterparts.
- Use the clr/setbits_le32() family of macros rather than expanding code.
- Use accessor macros for bit-fields instead of _MASK and _OFFSET.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Define default SoC input clock frequencies for i.MX5/6 in order to get rid of
duplicated definitions.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Liu <r64343@freescale.com>
Cc: Matt Sealey <matt@genesi-usa.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
i2c didn't work on imx25 due to missing MXC_IPG_PERCLK. Now using
MXC_I2C_CLK on all imx systems using i2c.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Acked-by: Stefano Babic <sbabic@denx.de>
tested on a MCIMX257CJM4A which now reports :
CPU: Freescale i.MX25 rev1.2 at 399 MHz
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Register CCM_CHSCCDR (offset 0x34 in CCM) is named CCM_CHSCCDR in
reference manual, but was named chscdr in struct mxc_ccm_reg.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Add meaningful constants for each clock channels and use them for
enabling and disabling i.MX6 clocks.
Includes an update to enable/disable the IPU1 clock in
drivers/video/ipu_common to remove IMX5x register access
when used on i.MX6 as discussed in V1:
http://patchwork.ozlabs.org/patch/185129/
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Boards may require a different pinmux setup for NAND than the default one.
Add a way to call into board specific code to set this up.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The prototypes used in board files were all scattered out, which lead to
code duplication between SPL and normal U-Boot and some prototypes not actually
being used. Consolidate this in a common board header.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Secondary config for the Flash attachment.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Rename board provided gpio_config_uart() to
gpio_early_init_uart() as it does the same thing as the equally
called function provided by the uart-switch code. This allows
to simply call this function in early board init whether or not
we are building with CONFIG_UART_SWITCH defined.
Also provide a weak symbol for this function, to avoid the
need to provide this function for boards that don't need any
fixup.
This patch supersedes the earlier posted
"tegra: convert gpio_config_uart to weak symbol".
Build tested with MAKEALL -s tegra20
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Common practice on Tegra 2 boards is to use the pllp_out4 FO
to generate the ULPI reference clock. For this to work we have
to override the default hardware generated output divider.
This function adds a clean way to do so.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Most Tegra boards output the ULPI reference clock on pad DEV2.
Complete the periph_id enum so that we are able to enable this
clock output circuit.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The move is pretty straight-forward. ap20.h and tegra20.h were renamed to ap.h and tegra.h.
Some files remain in arch-tegra20 but 'include' a file in 'arch-tegra' with #defines & structs
that will be common between T20 and T30 HW. HW-specific #defines, etc. stay in the 'arch-tegra20'
'root' file.
All boards build OK w/MAKEALL -s tegra20. Checkpatch.pl runs clean. Seaboard works OK.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Move files that are going to be common between T20 and T30 into 'tegra-common'
subdirs in AVP (arm720t), CPU (armv7), and shared (arch/arm/cpu/.) areas. Any
files that are left behind in '/tegra20' will be copied to '/tegra30' subdirs
and modified for that SoC. The 'common' files should need only minor changes.
Include files (arch/arm/include/asm/arch-tegra/tegra20) will be done in a
follow-on patch.
Builds fine w/MAKEALL -s tegra20. Checkpatch.pl is clean.
Signed-off-by: Tom Warren <twarren@nvidia.com>
This adds the required code to set up a ULPI USB port. It is
mostly a port of the Linux ULPI setup code with some tweaks
added for more correctness, discovered along the way of
debugging this.
To use this both CONFIG_USB_ULPI and CONFIG_USB_ULPI_VIEWPORT
have to be set in the board configuration file.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Kill off ehci-core.h
It was used to specify some static controller data. To support more than
one controller being active at any time we have to carry the controller
data ourselfes. Change the ehci interface accordingly.
NOTE: OMAP implemented the ehci stuff a bit backwards and should be fixed
to do the same thing as other platforms. But the change for now is at least
compile clean.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Carry an index in the lowlevel usb functions to make specify the
respective usb controller.
Also pass through an controller struct from lowlevel_init to the
creation of the root usb device of this controller.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Remove the parts depending either on disabled CONFIG_SERIAL_MULTI
or ifdefs around CONFIG_SERIAL_MULTI parts since CONFIG_SERIAL_MULTI
is now enabled by default.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Remove the empty bodies from serial_* functions from MXS SPL code.
These empty implementations are now in common/serial.c instead so
declaring them also in the SPL code would cause a colision once
serial multi is enabled unconditionally.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
Under option -munaligned-access, gcc can perform local char
or 16-bit array initializations using misaligned native
accesses which will throw a data abort exception. Fix files
where these array initializations were unneeded, and for
files known to contain such initializations, enforce gcc
option -mno-unaligned-access.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
[trini: Switch to usign call cc-option for -mno-unaligned-access as
Albert had done previously as that's really correct]
Signed-off-by: Tom Rini <trini@ti.com>
The restore sequence in lowlevel_init was in the wrong order,
causing lr to lose its original value and be set equal to ip
instead. Also, its use of the stack clashes with that of
s_init, so move the s_init call after the restore and turn
it into a tail-optimized branch.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
lowlevel_init() of rmobile badly assumed that ip register holds return address.
The commit "63ee53a7 armv7 cpu_init_crit: Simplify code" breaks this assumption.
This patch removes this bad assumption and simplify code.
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
This patch aims at ensuring that the 2012.10 release works
out-of-the-box on as many targets as possible, by reinstating
commit 5347560f5427bcdd48a563b62180481606ac8044, which adds
option -mno-unaligned-access to armv7 builds.
This patch will be overriden immediately after release of 2012.10.
Add minimal support for Altera's SOCFPGA Cyclone 5 hardware.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Chin Liang See <clsee@altera.com>
Signed-off-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Tom Trini <trini@ti.com>
Cc: Wolfgang Denx <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefan Roese <sr@denx.de>
----
v8: Remove no_return attribute for reset_cpu
Based on v2012.10-rc2
Add timer driver.
Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Joe Hershberger <joe.hershberger@gmail.com>
CC: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
When the u-boot address of destination equal to __start,
no relocation. relocation offset(r9) = 0.
Signed-off-by: Zhong Hongbo <bocui107@gmail.com>
Tested-by: Stefano Babic <sbabic@denx.de>
We don't need to return to cpu_init_crit after calling lowlevel_init, so
lowlevel_init can directly return to the caller of cpu_init_crit.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Disable sibling call optimization based on binutils version. This is
to work around a bug in the assember in binutils versions < 2.22.
Branches to weak symbols can be incorrectly optimized in thumb mode to
a short branch (b.n instruction) that won't reach when the symbol gets
preempted.
http://sourceware.org/bugzilla/show_bug.cgi?id=12532
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Tom Rini <trini@ti.com>
The bootm initrd image copy to ram can collide with the stack in cases
where the print buffer size is large (i.e. 1K). The result is intermittent
initrd decompression errors depending on the initrd size MOD 4KB since
the initrd start address is 4KB aligned.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
include/common.h has the reset_cpu defined already. No need to
re-define here.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Pavel Machek <pavel@denx.de>
Acked-By: Prafulla Wadaskar <Prafulla@marvell.com>
Size of the SDRAM chips might differ between any two (otherwise
identical) instances of the same board.
So add a function kw_sdram_size_adjust() which reads out the current
ram size for a given bank, and adjusts the Kirkwood's SDRAM window size
register accordingly.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Some boards might be equipped with different SDRAM configurations.
When that is the case, CPU CS Window Size Register (CS[0]n Size)
should be set to the biggest value through board.cfg file; then its
value can be fixed at runtime according to the detected SDRAM size.
Therefore, implement kw_sdram_bs_set().
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Marek Vasut <marex@denx.de>
Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
Remove the defines and do this with a C-struct.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Marek Vasut <marex@denx.de>
Acked-By: Prafulla Wadaskar <Prafulla@marvell.com>
It's now possible to use the gpio driver interface
for s3c2440. This patch add iomux definitions too.
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Rmobile common timer driver diverts the same driver as SH architecture.
When it builds at the same place with source, it is no problem, but when
it builds out of source, it cannot build.
This patch revises this problem.
Reported-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Renesas R8A7740 has GPIO based PFC. This privode framework of PFC.
The code included in this base from linux kernel.
Signed-off-by: Hideyuki Sano <hideyuki.sano.dn@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Renesas R8A7740 is CPU with Cortex-A9.
This supports the basic register definition and GPIO.
Signed-off-by: Hideyuki Sano <hideyuki.sano.dn@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Some rmobile SoC has TMU base timer function. This supports TMU.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
There is rmobile without ICCICR.
ICCICR is initialized only when ICCICR is defined.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
According to SoC document, revision info is separated to integer part and
fracton part.
So I separete rmobile_get_cpu_rev() to rmobile_get_cpu_rev_integer() and
rmobile_get_cpu_rev_fraction().
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CPU info register was read wrongly by mistake. And function rmobile_get_cpu_rev() was not called properly.
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add dummy member to struct sh73a0_rwdt in sh73a0.h.
Without this, initializing watch dog timer goes wrong.
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Latest rmobile code was tested by using old gcc (gcc-4.4).
When we use gcc-4.6 (or later), the build is made, but does not work.
This solves a problem not to work by add -march=armv5 to compiple option
when we built in gcc-4.6 (or later).
I tested by linaro's compiler version 2012.04-20120426.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Do soft power on reset in U-Boot reset command.
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The KZM-A9-GT board has Renesas R-Mobile SH73A0, 512MB DDR2-SDRAM,
USB, Ethernet, and more.
This patch supports the following functions:
- 512MB DDR2-SDRAM
- 16MB NOR Flash memory
- Serial console (SCIF)
- Ethernet (SMSC)
- I2C
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Renesas SH73A0 has GPIO based PFC. This privode framework of PFC.
The code included in this base from linux kernel.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Renesas SH73A0 is CPU with Cortex-A9.
This supports the basic register definition and GPIO.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds minimum support for R-Mobile. Only minimal support with timer.
This CPU can uses the peripheral of Renesas SuperH.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
ARMv7 has global timer. This provides the register definition of this timer.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add an option, CONFIG_BOOTSTAGE_FDT to pass boot timings to the kernel
in the device tree, if available. To use this, you must have
CONFIG_OF_LIBFDT defined.
Signed-off-by: Simon Glass <sjg@chromium.org>
U-boot should not ignore getting the bootmode passed on from the bootrom.
With this, U-boot SPL knows it was loaded from MMC1 and use this info to
read full U-boot from MMC1 as well.
Cc: pprakash@ti.com
Cc: trini@ti.com
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds support for networking in SPL. Some devices are
capable of loading SPL via network so it makes sense to load the
main U-Boot binary via network too. This patch tries to use
existing network code as much as possible. Unfortunately, it depends
on environment which in turn depends on other code so SPL size
is increased significantly. No effort was done to decouple network
code and environment so far.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@ti.com>
- Convert the non-relocation part of board_init_f to spl_board_init, turn on CONFIG_SPL_BOARD_INIT in the configs.
- Remove duplicated code.
- Add spl_boot_device() that returns the statically chosen boot device.
Signed-off-by: Tom Rini <trini@ti.com>
We move the spl_nand_load_image function to common/spl. This will allow
for easier integration of SPL-boots-Linux code on other arches.
Signed-off-by: Tom Rini <trini@ti.com>
In SPL (CONFIG_SPL_FRAMEWORK) board_init_f must setup the stack pointer,
clear the BSS and call board_init_r. We mark this as weak as some
platforms may need to perform additional initalization at this point.
We provide a gd that we know will be in a usable location, once the BSS
has been cleared to help with this as well. Finally, we no longer call
relocate_code so remove that from the armv7 version.
Next, both board_init_f and jump_to_image_linux are going to be
inherently arch-specific, so move these versions to arch/arm/lib/spl.c
Signed-off-by: Tom Rini <trini@ti.com>
Add a new flag, CONFIG_SPL_FRAMEWORK to opt into the common/spl SPL
framework, enable on all of the previously using boards. We move the
spl_ymodem.c portion to common/ and spl_mmc.c to drivers/mmc/. We leave
the NAND one in-place as we plan to replace it later in this series.
We use common/spl to avoid linker problems with respect to merging
constant strings in objects. Otherwise all strings in common/ will be
linked in and kept which grows SPL in size too much.
Signed-off-by: Tom Rini <trini@ti.com>
This is an OMAP/related-specific function, move calling it to
spl_board_init() and turn on CONFIG_SPL_BOARD_INIT on the boards that
enabled NAND and didn't enable this already.
Signed-off-by: Tom Rini <trini@ti.com>
- Remove includes we don't need
- Switch some printf statements to puts
- Convert some printf statements to debug, introduce new puts statements
- In most cases saying just "No mkimage signature, assuming
u-boot.bin" or similar is sufficient. This also means the non-DEBUG
case doesn't need printf, in the core of SPL.
- The other case here is that PLAIN_VERSION provided what we wanted
already, so just use it.
Signed-off-by: Tom Rini <trini@ti.com>
Move the default omap/related-centric board_mmc_init to
arch/arm/cpu/armv7/omap-common/boot-common.c and move the type defines
to <asm/spl.h>. Also use mmc->read_bl_len rather than MMCSD_SECTOR_SIZE
Signed-off-by: Tom Rini <trini@ti.com>
Move the SPL prototypes from <asm/omap_common.h> into <asm/spl.h> and
add <asm/arch/spl.h> for arch specific portions of CONFIG_SPL_FRAMEWORK.
Signed-off-by: Tom Rini <trini@ti.com>
We can only attempt to setup a malloc pool if
CONFIG_SYS_SPL_MALLOC_START is defined, and not all boards require it.
Make the call depend on the define.
Signed-off-by: Tom Rini <trini@ti.com>
Only omap4/5 currently have a meaningful set of display text and overo
had been adding a function to display nothing. Change how this works to
be opt-in and only turned on for omap4/5 now.
Signed-off-by: Tom Rini <trini@ti.com>
Commit 86c6326 "ARM: arm1176: enable instruction cache in
arch_cpu_init()" defined arch_cpu_init() in a file that is shared across
all arm1176 SoCs. tnetv107x already implemented this function, which
caused linking to break. Move the new conflicting arch_cpu_init() into
arm1176/bcm2835/init.c so that it doesn't conflict; grep indicates this
function is usually defined at the SoC-level, not the CPU-level, at least
for ARM.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
FSL 2.6.35 kernel assumes that the bootloader passes the CONFIG_REVISION_TAG
information.
If this data is not present, the kernel misconfigures the TZIC, which results in
the timer interrupt handler never being called, so the kernel deadlocks while
calibrating its delay.
Suggested-by: Greg Topmiller <Greg.Topmiller@jdsu.com>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
This board is the only board that still sticks to OneNAND IPL.
Remove this board, since we have SPL around for a while and
OneNAND is well supported in the SPL framework. The board can
be revived if necessary.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Tom Rini <trini@ti.com>
Constants set with binary value (0b...) are not compiled
from old toolchain when used by the clrsetbits_le32 macro.
Replaces them with the corresponding hex value.
The error reported (for example with the mx6qsabrelite board)
is something like:
mx6qsabrelite.c:369:1: error: invalid suffix "b101" on integer constant
mx6qsabrelite.c:369:1: error: invalid suffix "b10010" on integer constant
mx6qsabrelite.c:369:1: error: invalid suffix "b0000" on integer constant
mx6qsabrelite.c:369:1: error: invalid suffix "b10001" on integer constant
Signed-off-by: Stefano Babic <sbabic@denx.de>
Convert TEGRA20_ defines to either TEGRA_ or NV_PA_ where appropriate.
Convert tegra20_ source file and function names to tegra_, also.
Upcoming Tegra30 port will use common code/defines/names where possible.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
This allows for two things:
- VBus GPIO may be used on other ports than the OTG one
- VBus GPIO may be low active if specified by DT
Signed-off-by: Lucas Stach <dev@lynxeye.de>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Tom Warren <TWarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Up now only MX5 and MX6 can share code, because they have
a common source directory in cpu/armv7. Other not armv7
i.MX can profit of the same shared code. Move these files
into a directory accessible for all, similar to plat-mxc
in linux.
Signed-off-by: Stefano Babic <sbabic@denx.de>
A device tree is used to configure the NAND, including memory
timings and block/pages sizes.
If this node is not present or is disabled, then NAND will not
be initialized.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a NAND controller along with a bindings file for review.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add selection of NAND flash pins to the funcmux.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Define default SoC input clock frequencies for i.MX31 in order to get rid of
duplicated definitions.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Helmut Raiger <helmut.raiger@hale.at>
The MFN bit-field of the PLL registers represents a signed value. See the
reference manual.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Switch the mx35 timer driver to the 32-kHz clock source to avoid calling
mxc_get_clock() again and again, and to be consistent with the timer drivers of
other i.MX SoCs.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Define default SoC input clock frequencies for i.MX35 in order to get rid of
duplicated definitions.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
The clock dividers that were used do not match at all the reference manual. They
were either completely broken, or came from an early silicon revision
incompatible with the current one.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
The MFN bit-field of the PLL registers represents a signed value. See the
reference manual.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Useless code is removed, and get buswidth value.
buswidth value will be used to choice the 4bit or 8bit.
(Now used 4bit mode in sdhci.c by default)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
We have the timer code in arch/arm/cpu/armv7/omap-common/timer.c that
has been configuring and enabling the timer, so remove our code that
does the same thing by different methods.
Tested on EVM GP, SK-EVM and Beaglebone.
Signed-off-by: Tom Rini <trini@ti.com>
AM/DM37x SoCs add the CTRL_WKUP_CTRL register. It contains the
GPIO_IO_PWRDNZ bit, which is required to be set to enable the I/O pads
of gpio_126, gpio_127 and gpio_129.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Cc: Tom Rini <trini@ti.com>
The board_postclk_init() function can be used to perform operations
that requires a working timer early within the U-Boot init_sequence.
Signed-off-by: Markus Hubig <mhubig@imko.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Use proper struct-based access for this register in the SPL code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The computation was not correct with low clock values: setting a 1MHz
clock would result in an overlap that would then configure a 25Mhz
clock.
This patch implements a correct computation method according to the
kirkwood functionnal spec. table 600 (Serial Memory Interface
Configuration Register).
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Orion5x did not actually write GPIO output values
or input polarities, and ED Mini V2 had bad or
missing values for GPIO settings.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
* 'master' of git://git.denx.de/u-boot-usb:
MUSB driver: Timeout is never detected as the while loop does not end
usb: fix ulpi_set_vbus prototype
pxa25x: Add UDC registers definitions
USB: Fix strict aliasing in ohci-hcd
usb: Optimize USB storage read/write
ehci: Optimize qTD allocations
usb_stor_BBB_transport: Do not delay when not required
usb_storage: Remove EHCI constraints
usb_storage: Restore non-EHCI support
ehci-hcd: Boost transfer speed
ehci: cosmetic: Define used constants
ehci: Fail for multi-transaction interrupt transfers
arm:trats: Enable g_dnl composite USB gadget with embedded DFU function on TRATS
arm:trats: Support for USB UDC driver at TRATS board.
dfu:cmd: Support for DFU u-boot command
dfu: MMC specific routines for DFU operation
dfu: DFU backend implementation
dfu:usb: DFU USB function (f_dfu) support for g_dnl composite gadget
dfu:usb: Support for g_dnl composite download gadget.
ehci: cosmetic: Define the number of qt_buffers
Signed-off-by: Wolfgang Denk <wd@denx.de>
Define ARCH_MXC for i.MX devices. This is useful to identify features or
behaviors common to all i.MX SoCs.
The i.MX28 is omitted because its architecture is a bit different (like imx/mxc
vs. mxs in Linux).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kim Phillips <kim.phillips@freescale.com>
For representing a timeout value, it makes more sense to pass it as
'unsigned int'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Allow usage of the imx-common/iomux-v3.h framework by including pad settings
for the i.MX51. The content of the file is taken from Linux kernel at
commit 5d23b39 plus the required changes to make it work in U-Boot.
The contained pad settings are the minimum required to make an Efika MX boot
and get all the currently-implemented peripherals working in U-Boot.
It is recommended that this file not be just a dumping ground for pins but
only contain the settings required for all the boards using it.
Changes for v2:
* reference commit id from Linux kernel
* additionally roll in the USB pads
* removed GPIO_NUMBER define
Signed-off-by: Matt Sealey <matt@genesi-usa.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The DRAM initialization, after SPL has complete, is exactly the same
for all mxs SoCs so we should name it accordinly.
The following boards has been changed:
* apx4devkit
* m28evk
* mx28evk
* sc_sps_1
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Veli-Pekka Peltola <veli-pekka.peltola@bluegiga.com>
The internal Ethernet controller is only available on i.MX28
processors so it needs to use CONFIG_MX28 guardian to avoid having
this code called in others.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
The imx_decode_pll() function does not exist for mx5, so remove its declaration.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Each i.MX has its own gpio.h, defining the same structure.
The internal GPIO controller has the same layout
(at least for the register used by u-boot) and can be shared.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Tested-by: Matt Sealey <matt@genesi-usa.com>
commit d92591a (mxs: Convert sys_proto.h prefixes to 'mxs') introduced
a mxs_dram_init() function, which is not used anywhere.
Fix it, so that the following warning goes away:
mx28evk.c: In function ‘dram_init’:
mx28evk.c:67:2: warning: implicit declaration of function ‘mx28_dram_init’ [-Wimplicit-function-declaration]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
The elftosb call needs to use a target param specific for i.MX28. This
patch allow for later addition of i.MX233.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
Add cpu_mmc_init() function to make it easy to init a single eSDHC instance.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Do not pretend to have initialized mmc successfully if CONFIG_FSL_ESDHC is not
defined. Instead, only implement a custom cpu_mmc_init() when it does something.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
This is useful for forcing the ROM's
usb downloader to activate upon a watchdog reset.
Or, you can boot from either SD Card.
Currently, support added for MX53 and MX6Q
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Note: MX53 support untested.
Acked-by: Stefano Babic <sbabic@denx.de>
Round up tick_to_time() value instead of truncating it. This avoids stopping
waits instantly for low usec values, and this generally guarantees that the code
always waits for at least the requested duration.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Now that the main i.MX features work fine with dcache enabled, enabled it by
default if CONFIG_SYS_DCACHE_OFF is not defined.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Now that the main i.MX features work fine with dcache enabled, enabled it by
default if CONFIG_SYS_DCACHE_OFF is not defined.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Move some function calls to a more appropriate place, so they're
called only when needed.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The SPL doesn't need the CP15 reconfiguration, as that's what the
BootROM does for us already. Moreover, when the CP15 is reconfigured
and the code returns control to BootROM, the USB boot works no more.
Remove the code and allow [1] to work properly as well.
[1] http://git.bfuser.eu/?p=marex/mxsldr.git;a=summary
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The sys_proto.h functions (except the boot modes) are compatible with
i.MX233 and i.MX28 so we use 'mxs' prefix for its methods.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The iomux header is included on sys_proto.h so to avoid SoC specific
header inclusion.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
This patch enables the L1 data cache for systems based on Samsung
Exynos processor.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch support exynos pwm backlight driver. It can control backlight
power and brightness by using pwm.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
If dp_enabled was set, exynos fb driver support display port feature.
This patch depends on [PATCH] video: support exynos fimd driver
for various exynos series.
http://marc.info/?l=u-boot&m=134119605104467&w=2
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch set supports exynos display port drivers.
DisplayPort is an industry standard device to accommodate the increasing board
adoption of digital display technology within the PC and consumer electronics.
The interface supports internal chip-to-chip and external box-to-box digital
display connections.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch add display port base address for EXYNOS5. In case of EXYNOS4,
use DEVICE_NOT_AVAILABLE macro because DP is not supported.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch support display port phy control function.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch supports display block system regisger control.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch support exynos5 lcd clock control.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch supports exynos fimd driver for various exynos series different from
existing it supports only exynos4 chip.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Removed [-Wuninitialized] warning message.
The fout_sel is assigned to "-1" by default.
And start, gpio_func is initialized to 0.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In general, The get_timer_masked function get the system time,
no the number of ticks. Such as the nand_wait_ready will use
get_timer_masked to delay the operations. And change the system
time to adopt to the CONFIG_SYS_HZ.
Signed-off-by: Hongbo Zhong <bocui107@gmail.com>
Tested-by: Jaehoon Chung<jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch modifies the pinmux settings of MMC and UART as per
Exynos5250 Rev 1.0.
It also corrects the gpio offset calculations.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds support for BPLL clock.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
MPLL clock-out of Exynos5250 Rev 1.0 is always at 1.6GHz.
Adjust the divisor value to get 800MHz as needed by devices
like UART etc
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The patch adds the memory initialization sequence of DDR3.
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add a structure for table-driven configuration mechanism such that no recompilation
is needed to update the configuration parameters, rather than hard-coding
board initialization parameters.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
save_boot_params_default() in cpu.c accesses uninitialized stack area
when it compiled with -O0 (not optimized).
This patch removes save_boot_params_default() and put the equivalent in start.S
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Acked-by: Tom Rini <trini@ti.com>
These flags were necessary when building tegra20 as a single binary
that supported ARM7TDMI and Cortex A9. Now that the ARM7TDMI support
is split into a separate SPL, this is no longer necessary.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable the building of private libgcc for SPL
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add SPL options to tegra20 config files and enable SPL build for
tegra20 boards. Also remove redundant code from u-boot that is not
contained in SPL.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Move warmboot_save_sdram_params() to later in the boot sequence. This
code relies on devicetree to get the address of the memory controller
and with upcoming changes for SPL boot it gets called early in the
boot process when devicetree is not initialized yet.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add support for tegra20 arm7 boot processor. This processor is used
to power on the Cortex A9 and transfer control to it. In tegra this
processor is an ARM7TDMI not an ARM720T, but since we don't use cache
it was easier to just reuse the ARM720T code as the processors are
otherwise identical except for cache and MMU.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Take a few SPL fixes from armv7 and apply them to arm720t:
-Use dummy exception handlers for SPL build
-Initialize relocation register r9 to 0 for the case of no relocation
-ifdef out interrupt handler code
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
In preparation for splitting out the armv4t code from tegra20, move
the tegra20 SoC code to arch/arm/cpu/tegra20-common. This code will
be compiled armv4t for the arm7tdmi and armv7 for the cortex A9.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is make naming consistent with the kernel and devicetree and in
preparation of pulling out the common tegra20 code.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This SoC is used in the Raspberry Pi, for example.
For more details, see:
http://www.broadcom.com/products/BCM2835http://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf.
Initial support is enough to boot to a serial console, execute a minimal
set of U-Boot commands, download data over a serial port, and boot a
Linux kernel. No storage or network drivers are implemented.
GPIO driver originally by Vikram Narayanan <vikram186@gmail.com>
with many fixes from myself.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Note that this affects all users of the ARM1176 CPU that enable
CONFIG_ARCH_CPU_INIT, not just the BCM2835 SoC, potentially such as
tnetv107x.
Cc: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Following ARM's reference manuel for initializing the cache - the
kernel won't boot otherwise.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: John Rigby <john.rigby@linaro.org>
Some CPU (i.e u8500) need more cache management before launching
the Linux kernel.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: John Rigby <john.rigby@linaro.org>
Register mapping has changed on power control chip between
the first and second revision.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Tom Rini <trini@ti.com>
Functions such as providing power to the MMC device and reading
the processor version register should be in the cpu area for
access by multiple u8500-based boards.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Tom Rini <trini@ti.com>
LAN and GBF need to be powered explicitely, doing so with
interface to AB8500 companion chip.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: John Rigby <john.rigby@linaro.org>
Addresses between ux500.v1 and ux500.v2 have changed slightly,
hence mandating a review of the PRCMU access methods.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: John Rigby <john.rigby@linaro.org>
Enabling timers and clocks in PRCMU and cleaning up mailbox.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: John Rigby <john.rigby@linaro.org>
This is to allow the prcmu functions to be used by multiple
u8500-based processors.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: John Rigby <john.rigby@linaro.org>
We can safely use the same reset code written in C for both Davinci and
C6X platforms. In addition the C version of the code is marginally
smaller on Davinci.
Tested-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This patch updates secure_emif_sdram_config with the
same value written to sdram_config during ddr3 initialization.
During suspend/resume, this value is copied into sdram_config.
With this, a write to sdram_config at the end of resume sequence
which triggers an init sequence can be avoided.
Without this register write in place, the DDR_RESET line goes
low for a few cycles during resume which is a violation of the
JEDEC spec.
Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
Also enable the ohci port on hawkboard. These additions result in an
increased u-boot size -- adjust the same accordingly in the board's
config.
Move the usb header for da8xx platforms under arch-davinci.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Make sure that when we setup the stack before calling s_init() we have
the stack have 8-byte alignment for ABI compliance.
Tested-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Rini <trini@ti.com>
Make the lowlevel_init function that these platforms have which just
sets up the stack and calls a C function available to all armv7
platforms. As part of this we change some of the macros that are used
to be more clear. Previously (except for am335x evm) we had been
setting CONFIG_SYS_INIT_SP_ADDR to a series of new defines that are
equivalent to simply referencing NON_SECURE_SRAM_END. On am335x evm we
should have been doing this initially and do now.
Cc: Sricharan R <r.sricharan@ti.com>
Tested-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Rini <trini@ti.com>
- Correct the MMC1 base offset
- Remove MMC2 (that area is reserved and not MMC2).
- Add the real BOOT_DEVICE_MMC2 value
Signed-off-by: Tom Rini <trini@ti.com>
This gets us rid of duplication of the same file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
If VDDIO has a brownout, then the VDD5V_GT_VDDIO becomes unreliable
but this wasn't clear on code so a comment has been added to clarify
it.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
As the register accessing mode is the same for all i.MXS SoCs we ought
to use 'mxs' prefix intead of 'mx28'.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Most code can be shared between i.MX23 and i.MX28 as both are from
i.MXS family; this source directory structure makes easy to share code
among them.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
The mx28 prefix has been added to the initialization data and function
so it is clear by which SoC it is used as i.MX233 will have a specific
one. While on that, we also change it to static.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
The information now is gathered from HW_DIGCTL_CHIPID register and
includes the chip modem and revision on the output.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
In case an unidentified CPU type is detected it now returns
i.MX??, in a const char.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Markus Hubig <mhubig@imko.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add at91sam9x5ek board support, this board support the following SoCs
AT91SAM9G15, AT91SAM9G25, AT91SAM9G35, AT91SAM9X25, AT91SAM9X35
Using at91sam9x5ek_nandflash to configure for the board
Now only supports NAND with software ECC boot up
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[move MAINTAINERS entry to right place]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
For the DA8xx family of SoCs, the set_cpu_clk_info() function was not
initialising the DSP frequency, leading to 'bdinfo' command output such as:
[...snip...]
ARM frequency = 300 MHz
DSP frequency = -536870913 MHz
DDR frequency = 300 MHz
This commit provides a separate implementation of set_cpu_clk_info() for
the DA8xx SoCs that initialises the DSP frequency to zero (since
currently the DSP is not enabled by U-Boot on any DA8xx platform). The
separate implementation is justified because there is no common code
between DA8xx and the other SoC families. It is now much easier to
understand the flow of the two separate functions.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Cc: Tom Rini <trini@ti.com>
Cc: Hadli, Manjunath <manjunath.hadli@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Replace a magic number for the DDR2/mDDR PHY clock ID with a proper
definition. In addition, don't request this clock ID on DA830 hardware,
which does not have a DDR2/mDDR PHY (or associated PLL controller).
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Cc: Tom Rini <trini@ti.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
On the DA830, UART2's clock is derived from PLL controller 0 output 2.
On the DA850, it is in the ASYNC3 group, and may be switched between PLL
controller 0 or 1. Fix the definition of the ID to match.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Cc: Tom Rini <trini@ti.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Tidy up the clock IDs defined for the DA8xx SOCs. With this new structure in
place, it is clear how to define new clock IDs, and how these map to the
numbers presented in the technical reference manual.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Cc: Tom Rini <trini@ti.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
- Move definition of the EEPROM contents to <asm/arch/sys_proto.h>
- Make some defines a little less generic now.
- Pinmux must be done by done by SPL now.
- Create 3 pinmux functions, uart0, i2c0 and board.
- Add pinmux specific to Starter Kit EVM for MMC now.
Signed-off-by: Tom Rini <trini@ti.com>
- Board requires gpio0 #7 to be set to power DDR3.
- Board uses DDR3, add a way to determine which DDR type to call
config_ddr with.
- Both of the above require filling in the header structure early, move
it into the data section.
Signed-off-by: Tom Rini <trini@ti.com>
The intention has always been (and boards are to support) an i2c EEPROM
that will identify what hardware they are, allowing a single binary to
support multiple boards. As such, remove the 'evm.c' file as there is
nothing EVM centric in it currently, only SoC peripheral configuration.
Signed-off-by: Tom Rini <trini@ti.com>
In order to support DDR3 as well as DDR2, we need to perform the same
init sequence, but with different values. So change config_ddr() to
toggle setting pointers/etc for what DDR2 wants, and then calling.
Signed-off-by: Tom Rini <trini@ti.com>
The ddr_regs struct was incorrectly offset after the dt0wiratio0 entry.
Correct this by documenting a missing register that will be used at some
point in the future (when write leveling is supported). Further, the
cmdNcs{force,delay} fields are undocumented and we have been setting
them to zero, remove. Next, setting of the
'DATAn_REG_PHY_USE_RANK0_DELAYS field belongs with the rest of the
ddr_data entries, so program it there. Finally, comment on how we are
configuring the DATA1 registers that correspond to the DATA0 (dt0)
registers defined in the struct.
Signed-off-by: Tom Rini <trini@ti.com>
The various ratio1 fields are not documented in any of the documentation
I can find. Removing these and testing has yielded success, so remove
the code that sets them and move their locations into the reserved
fields.
Signed-off-by: Tom Rini <trini@ti.com>
This function sets a number of related registers to the same value (the
registers in question all have the same field descriptions and are
related in operation). Rather than defining a struct and setting the
value repeatedly, just pass in the value.
Signed-off-by: Tom Rini <trini@ti.com>
Rather than defining our own structs to note what to use when
programming the EMIF and related re-use the emif_regs struct.
Signed-off-by: Tom Rini <trini@ti.com>
A number of memory initalization functions were int and always returned
0. Further it's not feasible to be doing error checking here, so simply
turn them into void functions.
Signed-off-by: Tom Rini <trini@ti.com>
- Remove the call to set ddrctrl->ddrioctrl as it's all zeros.
- Comment what we're really setting in ddrctrl->ddrckectrl which is that
we're operating in the normal mode where EMIF/PHY clock is controlled
by the PHY.
Signed-off-by: Tom Rini <trini@ti.com>
EMIF parameters are calculated based on the AC timing
parameters from the SDRAM datasheet and the DDR frequency.
Current values for these paramters in AM335x U-Boot code,
though reliable, are not fully optimal. The most optimal
settings can be derived based on the guidelines published
at [1]. A pre-computed set of values with the most optimum
settings for AM335x EVM and BeagleBone can be found at [2].
[1] http://processors.wiki.ti.com/index.php/AM335x_EMIF_Configuration_tips
[2] http://processors.wiki.ti.com/index.php/OMAP_and_Sitara_CCS_support#AM335x
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Depending on if we have DDR2 or DDR3 on the board we will need to call
ddr_pll_config with a different value. This call can be delayed
slightly to the point where we know which type of memory we have.
Signed-off-by: Tom Rini <trini@ti.com>
We need to pass in the type of memory that is connected to the board.
The only reliable way to do this is to know what type of board we are
running on (which later will be knowable in s_init()). For now, pass in
the value of DDR2.
Signed-off-by: Tom Rini <trini@ti.com>
Rework the EMIF4/DDR code slightly to setup the structs that
config_cmd_ctrl and config_ddr_data take to be setup at compile time and
mark them as const. This lets us simplify the calling path slightly as
well as making it easier to deal with DDR3.
Signed-off-by: Tom Rini <trini@ti.com>
With the previous bugfix we now don't need to set two different REF_CTRL
values and instead set the final value.
Signed-off-by: Tom Rini <trini@ti.com>
When we change SDRAM_CONFIG this triggers a refresh based on all of the
parameters that we have programmed so we must do this last.
Signed-off-by: Tom Rini <trini@ti.com>
We do not need to check for EMIF_GCLK and L3_GCLK being active. This
was a hold-over from bringup and no longer required.
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds pin mux settings for CPSW switch found on
TI AM335X based boards (MII and RGMII modes).
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
[Ilya: split pinmux into separate patch]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
This patch adds platform-specific initialization for CPSW
switch on TI AM33XX SoCs.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
[Ilya: split init out of original patch]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
follow section 15.2.13.1 (Initializing Following Device Power Up or Reset) of
OMAP-L138 DSP+ARM Processor Technical Reference Manual
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
This reverts commit 5347560f5427bcdd48a563b62180481606ac8044,
which was applied only to get release 2012.07 functional on as
many ARM targets as possible despite mis-aligned accesses.
DA850/OMAP-L138 does not support strict MMC/SD boot mode. SPL will
be in SPI flash and U-Boot image will be in MMC/SD card. SPL will
do the low level initialization and then loads the u-boot image
from MMC/SD card.
Define CONFIG_SPL_MMC_LOAD macro in the DA850/OMAP-L138
configuration file to enable this feature.
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
initialize baudrate, flags, data and serial initialization,
only when CONFIG_SPL_LIBCOMMON_SUPPORT is defined.
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
This patch adds support for MMC/SD on DA850/OMAP-L138.
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
This patch uses the code in omap-common to support gpio modules 1-3
on am33xx based boards.
It adds base address and register definitions, enables clocks to the
modules, and enables building the common gpio code for CONFIG_AM33XX
as well as CONFIG_OMAP
Signed-off-by: Steve Sakoman <steve@sakoman.com>
This patch moves all bootcount implementations into a common
directory: drivers/bootcount. The generic bootcount driver
is now usable not only by powerpc platforms, but others as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Manfred Rudigier <manfred.rudigier@omicron.at>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
Tested-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
All the global flag defines are the same across all arches. So unify them
in one place, and add a simple way for arches to extend for their needs.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
struct s3c24x0_i2c is being moved to common local header file so that
the same can be used by s3c series and exynos series SoCs.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch defined EXYNOS5_I2C_SPACING used to calculate I2C channel
base address.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch adds the base address for I2C.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This adds i2c clock information for EXYNOS5.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
bad_cache_range actually returned true if the range was OK, but it was used
according to its name, which resulted in all valid dcache range invalidate/flush
operations being dropped. Hence, most DMA transfers resulted in garbage data.
This patch renames this function according to what it does, and it fixes the
interpretation of its return value by other functions. The chosen naming is the
same as for ARM926EJ-S in order to be consistent.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Stefano Babic <sbabic@denx.de>
Use the same name as defined in the datasheet.
DSP_CLK -> DISP_CLK
Signed-off-by: Ashok Kumar Reddy Kourla <ashokkourla2000@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Create a weak-aliased arch_cpu_init, so that we can get rid of CONFIG_ARCH_CPU_INIT
and always call arch_cpu_init.
This way we do not need to define CONFIG_ARCH_CPU_INIT in every board file, since
arch_cpu_init() is supposed to handle common CPU level code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Recent compiler generates unaligned memory access in armv7 default.
But current U-Boot does not allow unaligned memory access, so it causes
data abort exception.
This patch add compile option "-mno-unaligned-access" if it is available.
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Tested-by: Gary Thomas <gary@mlbassoc.com>
In currently, when __bss_start is equal to __bss_end__,
The bss loop will clear all the things in memory space.
But just only when __bss_end__ greater than __bss_start__,
we do the clear bss section operation.
Signed-off-by: Zhong Hongbo <bocui107@gmail.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
* 'next' of git://git.denx.de/u-boot-video:
ipu_common: Add ldb_clk for use in parenting the pixel clock
ipu_common: Do not hardcode the ipu_clk frequency
ipu_common: Rename MXC_CCM_BASE
ipu_common: Let clk_ipu_enable/disable only run on MX51 and MX53
ipu_common: Only apply the erratum to MX51
video: Rename CONFIG_VIDEO_MX5
mx6: Allow mx6 to access the IPUv3 registers
common lcd: minor coding style changes
Signed-off-by: Wolfgang Denk <wd@denx.de>
The following platforms had their config files changed
flea3, imx31_phycore, mx35pdk, mx53ard, mx53evk, mx53smd
and mx53loco.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
* 'master' of git://git.denx.de/u-boot-arm:
tegra: define fdt_load/fdt_high variables
tegra: enable bootz command
tegra: usb: Fix device enumeration problem of USB1
tegra: trimslice: set up serial flash pinmux
tegra: add pin_mux_spi() board initialization function
tegra: add GMC/GMD funcmux entry for SFLASH
tegra: bootcmd: start USB only when needed
tegra: bootcmd enhancements
tegra: add enterrcm command
tegra: enable CONFIG_ENV_VARS_UBOOT_CONFIG
Add env vars describing U-Boot target board
tegra: usb: fix wrong error check
tegra: add ULPI on USB2 funcmux entry
tegra: fix leftover CONFIG_TEGRA2_MMC & _SPI build switches
tegra: Add Tamonten Evaluation Carrier support
tegra: Use SD write-protect GPIO on Tamonten
tegra: Implement gpio_early_init() on Tamonten
tegra: Allow boards to perform early GPIO setup
tegra: plutux: Add device tree support
tegra: medcom: Add device tree support
tegra: Rework Tamonten support
beagle: add eeprom expansion board info for bct brettl4
Signed-off-by: Wolfgang Denk <wd@denx.de>
* 'master' of git://git.denx.de/u-boot-usb:
CONFIG: EXYNOS5: USB: Enable USB 2.0 on smdk5250
EXYNOS5: USB: Fix incorrect USB base addresses
EXYNOS: Add power Enable/Disable for USB-EHCI
USB: EXYNOS: Set USB 2.0 HOST Link mode
EXYNOS5: Add structure for PMU registers
EXYNOS5: Fix system register structure
USB: EXYNOS: Incorporate EHCI review comments
Signed-off-by: Wolfgang Denk <wd@denx.de>
A known hardware issue of USB1 port where bit 1 (connect status
change) of PORTSC register will be set after issuing Port Reset
(like "usb reset" in u-boot command line).
This will be treated as an error and stops later device enumeration.
Therefore we clear that bit after Port Reset in order to proceed
later device enumeration.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra's boot ROM supports a mode whereby code may be downloaded and flash
programmed over a USB connection. On dev boards, this is typically entered
by holding down a "force recovery" button and resetting the CPU. However,
not all boards have such a button (one example is the Compulab Trimslice),
so a method to enter RCM from software is useful.
This change implements the command "enterrcm" to do this, and enables it
for all Tegra boards by default. Even on boards other than Trimslice,
controlling this over a UART may be useful, e.g. to allow simple remote
control without the need for mechanical button actuators, or hooking up
relays/... to the button.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
loop_count runs down from 10000, so the correct condition to error out
is ==0.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Tom Warren <twarren.nvidia@gmail.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is needed as a prerequisite for Tegra USB ULPI support
within U-Boot.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch corrects the base addresses for USB_PHY and USB_OTG.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Chander Kashyap <chander.kashyap@linaro.org>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds functions to enable/disable the power of USB
host controller for EXYNOS5.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
This patch corrects the SYSREG structure.
We have removed the sysreg.h added in the previous patchset
version as the sysreg structure is already defined in system.h.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
This reverts commit fa042186b9.
It causes build warnings like this:
cpu.c:48:1: warning: -fstack-usage not supported for this target
[enabled by default]
Signed-off-by: Wolfgang Denk <wd@denx.de>
The following is the cleanup sequence in arch/arm/cpu/armv7/cpu.c
int cleanup_before_linux(void)
{
...
...
dcache_disable();
v7_outer_cache_disable();
invalidate_dcache_all();
}
1) invalidate_dcache_all call expects that all the caches has been
flushed, invalidated and there are no dirty entries prior to its
execution. In the above sequence dcache_disable() flushes, invalidates
the caches and turns off the mmu. But after it cleanups the cache
and before the mmu is disabled there is a cp_delay() function which
has STR instruction. On certain cores like the cortex-a15, cache hit
and a write can happen to a cache line even when the dcache is
disabled. So the above mentioned STR instruction creates a dirty entry
after cleaning. The mmu gets disabled after this.
2) invalidate_dcache_all invalidates the cache lines. Again on
cores like cortex-a15, invalidate instruction flushes the dirty
line as well. So some times the dirty line from sequence 1
can corrupt the memory resulting in a crash.
Fixing this by moving the get_cr() and cp_delay() calls before
cleaning up the cache, thus avoiding the dirty entry.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Introduce arch_early_init_r() function, which can be useful for doing
early initialization after relocation has happened.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
No need to define CONFIG_ARCH_CPU_INIT.
All mx28 based boards should use arch_cpu_init().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
This patch adds SPL support for SPEAr600. Currently only SNOR
(Serial NOR) flash support is included. Other boot devices
(NAND, MMC, USB ...) may be added with later patches.
Tested on the STM SPEAr600 evaluation and x600 SPEAr600 boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
raise() likes to call printf() if it is available, but in SPL builds it
either is not available, or adds a large chunk to the resulting image
size.
So don't call it even if it is available.
This change reduces SPL size from 10KB to 6.3KB on hawkboard, for
example, using generic relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefan Roese <sr@denx.de>
In SPEAr configuration files, unnecessary paranthesis are used in some
\#defines. Remove them as they serve no purpose
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
SoC Core ID offset is 0x30 in miscellaneous configuration address
space. It was wrongly mentioned as periph2 clk enable.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
UART in u-boot intends to run on 48MHz clock supplied by USB PLL.
Explicitly select the intended clock source.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Earlier, architecture specific init code was mixed with board initialization
code in board/spear/... This patch updates architecture support for SPEAr in
latest u-boot and prints the SoC information.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
SPEAr310 and SPEAr320 SoCs have an extra ethernet controller. The
driver for this device is already supported by u-boot, so configuring
board configuration file and defining base addresses etc to make use
of the common driver
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Xloader table was used primarily to inform u-boot about the DDR size. However,
now the ddr size is calculated at runtime which eliminates any need for the
Xloader table. So removing this unnecessary code.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
SMI is the serial memory interface controller provided by ST.
Earlier, a driver exists in the u-boot source code for the SMI IP. However, it
was specific to spear platforms. This commit converts the same driver to a more
generic driver. As a result, the driver files are renamed to st_smi.c and
st_smi.h and moved into drivers/mtd folder for reusability by other platforms
using smi controller peripheral.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Since FSMC is a standard IP and it supports different memory interfaces, it
is supported independent of spear platform and spear is configured to use that
driver for interfacing with the NAND device
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
save_boot_params_default() in cpu.c accesses uninitialized stack area
when it compiled with -O0 (not optimized).
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Acked-by: Tom Rini <trini@ti.com>
USB clocks will be required for fastboot, tftp
related functionalities. Move these clocks to
essential group inorder to have the functionality
working when non-essential clocks are not enabled.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
GPMC clocks are currently getting enabled as a part
non-essential clocks. This will be required during
NOR boot. Move this to essential group to keep the
functionality, when non-essential clocks are not
enabled.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The external phy is present in the case OMAP5 soc is currently
configured in emif-common.c. This results in having dummy structures
for those Socs which do not have a external phy. So by having a weak
function in emif-common and overriding it in OMAP5, avoids the use
of dummy structures.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
This reduced M,N couple corresponds to the advised value from
TI HW team.
Tested on 4460 Pandaboard, it also provides peripheral clocks
closer to the advised values.
Signed-off-by: Sebastien Jan <s-jan@ti.com>
The PLL setup values currently assume a 24 Mhz input clock.
This patch uses V_OSCK from the board config file to support boards
with different input clock rates.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Code currently tests for <= 0xff. Micron manufacturer code is 0xff, so
Micron memory will not be detected!
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Some rams (Micron for example) return duplicate mr data on all byte lanes.
Users of the get_mr function currently don't deal with this duplicated
data gracefully. This patch detects the duplicated data and returns only
the expected 8 bit mr data.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Errata ID:i727
Description: The refresh rate is programmed in the EMIF_SDRAM_REF_CTRL[15:0]
REG_REFRESH_RATE parameter taking into account frequency of the device.
When a warm reset is applied on the system, the OMAP processor restarts
with another OPP and so frequency is not the same. Due to this frequency
change, the refresh rate will be too low and could result in an unexpected
behavior on the memory side.
Workaround:
The workaround is to force self-refresh when coming back from the warm reset
with the following sequence:
• Set EMIF_PWR_MGMT_CTRL[10:8] REG_LP_MODE to 0x2
• Set EMIF_PWR_MGMT_CTRL[7:4] REG_SR_TIM to 0x0
• Do a dummy read (loads automatically new value of sr_tim)
This will reduce the risk of memory content corruption, but memory content
can't be guaranteed after a warm reset.
This errata is impacted on
OMAP4430: 1.0, 2.0, 2.1, 2.2, 2.3
OMAP4460: 1.0, 1.1
OMAP4470: 1.0
OMAP5430: 1.0
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
EMIF and DDR device state are preserved in warmreset. Redoing the full
initialisation would cause unexpected behaviour. Do only partial
initialisation to account for frequency change.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Certain modules are not affected by means of
a warm reset and need not be configured again.
Adding an API to detect the reset reason warm/cold.
This will be used to skip the module configurations
that are retained across a warm reset.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Interrupts and exceptions doesn't work in relocated code.
It badly use IRQ_STACK_START_IN in rom area as interrupt stack.
It is because the vecotr table is not moved to ram area.
This patch moves vector table before jumping relocated code.
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Tested-by: Tom Rini <trini@ti.com>
So that they can be redefined by some boards specific values.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
These two function nows ensure that the MPP is configured correctly for
the SPI controller before any SPI access, and restore the initial
configuration when the access is over.
Since the used pins for the SPI controller can differ (2 possibilities
for each signal), the used pins are configured with CONFIG_SYS_KW_SPI_MPP.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
If a second non NULL argument is given to the kirkwood_mpp_conf
function, it will be used to store the current configuration of the MPP
registers. mpp_save must be a preallocated table of the same size as
mpp_list and it must be zero terminated as well.
A later call to kirkwood_mpp_conf function with this saved list as first
(mpp_conf) argment will set the configuration back.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Enable new PIO feature supported by Atmel SoC.
Using CPU_HAS_PIO3 micro to enable PIO new feature.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The commit "i.mx: fsl_esdhc: add the i.mx6q support" (4692708d) introduces
support for the i.MX6Q MMC host controller USDHC.
MXC_IPG_PERCLK sets the clock to 66MHz. This seems to be the default clock
of the ESDHC IP found in < i.MX6 silicon. However, the default clock for the USDHC
IP found in i.MX6 is 200MHz (MXC_ESDHC_CLK). This difference will cause a 3 times
higher clock on SD_CLK than expected (see fsl_esdh.c -> set_sysctl()).
Signed-off-by: Michael Langer <michael.langer@de.bosch.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Jason Liu <r64343@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This function can be overridden at run-time and allows implementors
of new boards based on the i.MX28 chip to fine-tune the memory params.
It is possible to write into the dram_vals array because when the SPL
runs, it is located SRAM. Therefore the location is writable. There is
no possibility of these data to be read-only.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
The macro mistakenly referred to 32bit struct instead of 8bit one.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
SATA_ALT_REF_CLK field corresponds to bits 1 and 2 of offset 0x180c.
Fix the mask for these bits.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
If one PAD does not have mux or pad config register, we need
set the NO_MUX_I/NO_PAD_I to 0, the old value is not correct
Signed-off-by: Jason Liu <jason.hui@linaro.org>
CC: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
This patch performs the pinmux configuration in a common file.
As of now only EXYNOS5 pinmux for SDMMC, UART and Ethernet is
supported.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Chander Kashyap <chander.kashyap@linaro.org>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Since Exynos architecture have new SoCs,
need to fix cpuinfo correctly.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Chander Kashyap <chander.kashyap@linaro.org>
To meet certain timing requirements on the lpddr2 cmd and data phy
interfaces ,lpddr iopads have to be configured as differential buffers
and a Vref has to be internally generated and provided to these buffers.
Correcting the above settings here.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
In OMAP5432 EMIF controlller supports DDR3 device.
This patch adds support for ddr3 device intialization and configuration.
Initialization sequence is done as specified in JEDEC specs.
This also adds support for ddr3 leveling.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Previously, only the low 5 bits (NCH) were being transfered
from DDRVTPR to DDRVTPIOCR, the bits 5-9 where zeroed.
VTP_RECAL should be bit 15, not 18.
The only mainline board affected by this change is davinci_sonata.
The other Davinci boards define CONFIG_SKIP_LOWLEVEL_INIT.
However, if the program that loads u-boot on these boards
copied the code from u-boot, they will need fixed as well.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Please get tested by acks before applying, where tested by
means an overnight memory test.
Thanks
Troy
get_ram_size checks the given memory range for valid ram,
but expects the size of memory to be aligned to the power
of 2. In case of OMAP5 evm board the memory available is
2GB - 16MB(used for TRAP section) = 2032MB.
So always ensure that the size of memory used for testing is
aligned to the power of 2.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The unmapped entries in tiler space are set with
values 0xFF. So creating a DMM section of
size 16MB at 0xFF000000 with ADDRSPACE set to 0x2.
This way all the unmapped entry accesses to tiler
will be trapped by the EMIF and a error response
is sent to the L3 interconnect. L3 errors are
inturn reported to MPU.
Note that here the tiler trap section is overlapping
with the actual ddr physical space and we lose 16MB
out of the total 2GB.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The DMM sections can be overlapping with each other, with
sections 3 to 0 having the highest to lowest priority in that
order. There could also be a section that is used trap the
unmapped Tiler entries and this trap section could be
overlapping with the actual sdram area.
So take care of the above scenarios while calculating the
size of the actual ram.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Walk the BIT and BCT to find the ODMDATA word in the
CustomerData field and put it into Scratch20 reg for
use by kernel, etc.
Built all Tegra builds OK; Booted on Seaboard and saw
ODMDATA in PMC scratch20 was the same as the value in my
burn-u-boot.sh file (0x300D8011). NOTE: All flash utilities
will have to specify the odmdata (nvflash --odmdata n) on
the command line or via a cfg file, or built in to their
BCT.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
In anticipation of Tegra3 support, continue removing/renaming
Tegra2-specific files. No functional changes (yet).
Updated copyrights to 2012.
Signed-off-by: Tom Warren <twarren@nvidia.com>
In anticipation of Tegra3 support, start removing/renaming
Tegra2-specific files. No functional changes (yet).
Also updated copyright to 2012.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Override -march setting for tegra to -march=armv4t for files that are
necessary for low level init on tegra.
The recent change to use -march=armv7-a for armv7 caused a regression
on tegra because tegra starts boot on a arm7tdmi processor before
transferring control to the cortex-a9. While still executing on the
arm7tdmi there are calls to getenv_ulong() and memset() that cause an
illegal instruction exception if compiled for armv7.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Correct this warning seen by Albert:
ap20.c:44:18: warning: array subscript is above array bounds
There is a subtle bug here which currently causes no errors, but might
in future if people use PCI or the 32KHz clock. So take the opportunity
to correct the logic now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is based on top of:
tegra: add alternate UART1 funcmux entry
tegra: add UART1 on GPU funcmux entry
v2: remove enum change
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Tom Warren <twarren@nvidia.com>
CC: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
(In at least some configurations) Whistler uses UART1 on pingroups
UAA, UAB.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass's proposal to fix this on Seaboard was NAK'd, so I
removed his NS16550 references and added a small delay before
SPI/UART muxing. Tested on my Seaboard with large SPI reads/writes
and saw no corruption (crc's matched) and no spurious comm chars.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Jimmy Zhang <jimmzhang@nvidia.com>
Remove unnecessary brackets.
Unwrap lines which are below 80 chars.
Single line comment as single line (as the rest).
Moved init values to the source code.
cc: s-paulraj@ti.com
cc: khasim@ti.com
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
The beagle board uses the background color to show an orange screen during
startup. This patch adds the ability to add a frame buffer, with the
intention not to break the beagle board use case (I don't have one).
videomodes.c is not used. Scrolling depends on this patch:
http://patchwork.ozlabs.org/patch/155662/
cc: trini@ti.com
cc: s-paulraj@ti.com
cc: khasim@ti.com
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
s6e8ax0 panel has many panel of types. This patch support another panel
on TIZEN lunchbox board(HWREVISION 2). This panel has reversed panel
display type. So, I had added necessary command.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix:
npe.c: In function 'npe_initialize':
npe.c:630:13: warning: assignment from incompatible pointer type
Signed-off-by: Anatolij Gustschin <agust@denx.de>
* 'master' of git://git.denx.de/u-boot-usb:
USB: S5P: Add ehci support
usb:udc:samsung Add functions for storing private gadget data in UDC driver
usb:gadget:composite: Support for composite at gadget.h
usb:gadget:composite USB composite gadget support
usb:udc:samsung:cleanup Replace DEBUG_* macros with debug_cond() calls
usb:udc: Remove duplicated USB definitions from include/linux/usb/ch9.h file
USB: Document the QH and qTD antics in EHCI-HCD
USB: Drop cache flush bloat in EHCI-HCD
USB: Drop ehci_alloc/ehci_free in ehci-hcd
USB: Align buffers at cacheline
usb: use noinline define
* 'master' of git://git.denx.de/u-boot-arm: (167 commits)
OMAP4/5: Change omap4_sdp, omap4_panda, omap5_evm maintainer
ARM: omap3: Add CONFIG_SPL_BOARD_INIT for CONFIG_SPL_MMC_SUPPORT
ARM: omap3: Set SPL stack size to 8KB, image to 54KB.
arm, omap3: fix warm reset serial output on OMAP36xx/AM/DM37xx
OMAP4: Set fdt_high for OMAP4 devices to enable booting with Device Tree
omap4: do not enable auxiliary cores
omap4: do not enable fs-usb module
omap4: panda: disable uart2 pads during boot
igep00x0: change mpurate from 500 to auto
igep00x0: enable the use of a plain text file
tegra2: trivially enable 13 mhz crystal frequency
tegra: Enable keyboard for Seaboard
tegra: Switch on console mux and use environment for console
tegra: Add tegra keyboard driver
tegra: fdt: Add keyboard definitions for Seaboard
tegra: fdt: Add keyboard controller definition
tegra: Add keyboard support to funcmux
input: Add support for keyboard matrix decoding from an fdt
input: Add generic keyboard input handler
input: Add linux/input.h for key code support
fdt: Add fdtdec functions to read byte array
tegra: Enable LP0 on Seaboard
tegra: fdt: Add EMC data for Tegra2 Seaboard
tegra: i2c: Add function to find DVC bus
fdt: tegra: Add EMC node to device tree
tegra: Add EMC settings for Seaboard
tegra: Turn off power detect in board init
tegra: Set up warmboot code on Nvidia boards
tegra: Setup PMC scratch info from ap20 setup
tegra: Add warmboot implementation
tegra: Set up PMU for Nvidia boards
tegra: Add PMU to manage power supplies
tegra: Add EMC support for optimal memory timings
tegra: Add header file for APB_MISC register
tegra: Add tegra_get_chip_type() to detect SKU
tegra: Add flow, gp_padctl, fuse, sdram headers
tegra: Add crypto library for warmboot code
tegra: Add functions to access low-level Osc/PLL details
tegra: Move ap20.h header into arch location
Add AES crypto library
i2c: Add TPS6586X driver
Add abs() macro to return absolute value
fdt: Add function to return next compatible subnode
fdt: Add function to locate an array in the device tree
i.MX28: Avoid redefining serial_put[cs]()
i.MX28: Check if WP detection is implemented at all
i.MX28: Add battery boot components to SPL
i.MX28: Reorder battery status functions in SPL
i.MX28: Add LRADC init to i.MX28 SPL
i.MX28: Add LRADC register definitions
i.MX28: Shut down the LCD controller before reset
i.MX28: Add LCDIF register definitions
i.MX28: Implement boot pads sampling and reporting
i.MX28: Improve passing of data from SPL to U-Boot
M28EVK: Add SD update command
M28EVK: Implement support for new board V2.0
FEC: Abstract out register setup
MX5: PAD_CTL_DRV_VOT_LOW and PAD_CTL_DRV_VOT_HIGH exchanged
i.MX28: Add delay after CPU bypass is cleared
spi: mxs: Allow other chip selects to work
spi: mxs: Introduce spi_cs_is_valid()
mx53loco: Remove unneeded gpio_set_value()
mx53loco: Add CONFIG_REVISION_TAG
mx53loco: Turn on VUSB regulator
mx53loco: Add mc34708 support and set mx53 frequency at 1GHz
pmic: dialog: Avoid name conflicts
imx: Add u-boot.imx as target for ARM9 i.MX SOCs
i.MX2: Include asm/types.h in arch-mx25/imx-regs.h
imx: usb: There is no such register
i.MX25: usb: Set PORTSCx register
imx: nand: Support flash based BBT
i.MX25: This architecture has a GPIO4 too
i.MX25: esdhc: Add mxc_get_clock infrastructure
i.MX6: mx6q_sabrelite: add SATA bindings
i.MX6: add enable_sata_clock()
i.MX6: Add ANATOP regulator init
mx28evk: add NAND support
USB: ehci-mx6: Fix broken IO access
M28: Scan only first 512 MB of DRAM to avoid memory wraparound
Revert "i.MX28: Enable additional DRAM address bits"
M28: Enable FDT support
mx53loco: Add support for 1GHz operation for DA9053-based boards
mx53loco: Allow to print CPU information at a later stage
mx5: Add clock config interface
imx-common: Factor out get_ahb_clk()
i.MX6Q: mx6qsabrelite: Add keypress support to alter boot flow
mx31pdk: Allow booting a zImage kernel
mx6qarm2: Allow booting a zImage kernel
mx6qsabrelite: Allow booting a zImage kernel
mx28evk: Allow booting a zImage kernel
m28evk: Allow to booting a dt kernel
mx28evk: Allow to booting a dt kernel
mx6qsabrelite: No need to set the direction for GPIO3_23 again
pmic: Add support for the Dialog DA9053 PMIC
MX53: mx53loco: Add SATA support
MX53: Add support to ESG ima3 board
SATA: add driver for MX5 / MX6 SOCs
MX53: add function to set SATA clock to internal
SATA: check for return value from sata functions
MX5: Add definitions for SATA controller
NET: fec_mxc.c: Add a way to disable auto negotiation
Define UART4 and UART5 base addresses
EXYNOS: Change bits per pixel value proper for u-boot.
EXYNOS: support TRATS board display function
LCD: support S6E8AX0 amoled driver based on EXYNOS MIPI DSI
EXYNOS: support EXYNOS MIPI DSI interface driver.
EXYNOS: support EXYNOS framebuffer and FIMD display drivers.
LCD: add data structure for EXYNOS display driver
EXYNOS: add LCD and MIPI DSI clock interface.
EXYNOS: definitions of system resgister and power management registers.
SMDK5250: fix compiler warning
misc:pmic:samsung Convert TRATS target to use MAX8997 instead of MAX8998
misc:pmic:max8997 MAX8997 support for PMIC driver
TRATS: modify the trats's configuration
ARM: Exynos4: ADC: Universal_C210: Enable LDO4 power line for ADC measurement
EXYNOS: Rename exynos5_tzpc structure to exynos_tzpc
arm: ea20: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
arm: cam_enc_4xx: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
cm-t35: add I2C multi-bus support
include/configs: Remove CONFIG_SYS_64BIT_STRTOUL
include/configs: Remove CONFIG_SYS_64BIT_VSPRINTF
omap3: Introduce weak misc_init_r
omap730p2: Remove empty misc_init_r
omap5912osk: Remove empty misc_init_r
omap4+: Remove CONFIG_ARCH_CPU_INIT
omap4: Remove CONFIG_SYS_MMC_SET_DEV
OMAP3: pandora: drop console kernel argument
OMAP3: pandora: revise GPIO configuration
...
All arches init this the same way, so move the logic into the core
net code to avoid duplicating it everywhere else.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
This field gets read in one place (by "bdinfo"), and we can replace
that with getenv("ipaddr"). After all, the bi_ip_addr field is kept
up-to-date implicitly with the value of the ipaddr env var.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
In warm reset conditions on OMAP36xx/AM/DM37xx the rom code
incorrectly sets the DPLL4 clock input divider to /6.5 which
is an invalid value unless the input clock is 13MHz. When a JTAG
emulator is attached, a warm reset is necessary after the emulator
gains control of the process. This results in a loss of serial
output due to the invalid DPLL4 settings.
This patch fixes the issue by resetting the DPLL4 clock input
divider to /1 when the input clock is not 13MHz. AM/DM37x TRM
section 3.5.3.3.3.2.1 specifies that the /6.5 setting is only
used when the input clock is 13MHz.
Signed-off-by: Matt Porter <mporter@ti.com>
Booting up these cores (dsp / ivahd / cortex-m3) is bad without
firmware running on them, and they will hang preventing any kind
of sleep transitions later on with the kernel.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: R Sricharan <r.sricharan@ti.com>
If this is done in the bootloader, the FS-USB will later be stuck into
intransition state, which will prevent the device from entering idle.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This is needed for upcoming Toradex Colibri T20 upstream support.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Tegra keyboard controller provides a simple interface to a matrix
keyboard.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add tegra_i2c_get_dvc_bus_num() to obtain the I2C bus number of DVC bus.
This allows us to talk to the PMU.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a definition of the memory controller node according to the bindings
here:
http://patchwork.ozlabs.org/patch/132928/
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Save SDRAM parameters into the warmboot scratch registers
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Yen Lin <yelin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add code to set up the warm boot area in the Tegra CPU ready for a
resume after suspend.
Signed-off-by: Yen Lin <yelin@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Power supplies must be adjusted in line with clock frequency. This code
provides a simple routine to set the voltage to allow operation at maximum
frequency.
- Split PMU code into separate TPS6586X driver
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add support for setting up the memory controller parameters. Boards
can set up an appropriate table in the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a basic header file for this register, to be filled in as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We want to know which type of chip we are running on - the Tegra
family has several SKUs. This can be determined by reading a
fuse register, so add this function to ap20.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
These headers provide access to additional Tegra features.
flow - start/stop CPUs
sdram - parameters for SDRAM
fuse - access to on-chip fuses / security settings
gp_padctl - pad control and general purpose registers
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Yen Lin <yelin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Provides an interface to aes.c for the warmboot code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Yen Lin <yelin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add clock_ll_read_pll() to read PLL parameters and clock_get_osc_bypass()
to find out if the Oscillator is bypassed. These are needed by warmboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We want to include this from board code, so move the header into
an easily-accessible location.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This macro is generally useful to make it available in common.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Do not define serial_putc() and serial_puts() calls if
CONFIG_SPL_SERIAL_SUPPORT is set.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
This code is part of battery boot support for i.MX28.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
If the LCD controller is on before the CPU goes into reset, the traffic on LCDIF
data pins interferes with the BootROM's boot mode sampling. So shut the
controller down.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Pass memory size from SPL via structure located in SRAM instead of SCRATCH
registers. This allows passing more data about boot from SPL to U-Boot, like the
boot mode pads configuration.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
After an update to the MX51 reference manual (Rev. 5), the
values of the PAD_CTL_DRV_VOT_LOW and PAD_CTL_DRV_VOT_HIGH
are now clearly wrong:
"Bit 13:
High / Low Output Voltage Range. This bit selects the output voltage mode for
SD2_CMD. 0 High output voltage mode
1 Low output voltage mode"
The values are currently negated in code - fixed.
Reported-by: David Jander <david.jander@protonic.nl>
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: David Jander <david.jander@protonic.nl>
Acked-by: David Jander <david.jander@protonic.nl>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
This solves issues when larger amount of DRAM is used, like 256MB.
Behave the same in case of CPU bypass as we do in case of EMI
bypass, but wait 15 ms. We need to wait until the clock domain
stabilizes.
This issue seemed to have been caused by not waiting after frobbing
with the CPU bypass, it was unrelated to memory, but had a direct
impact, causing trouble. This was yet another X-File of the
imx-bootlets, sigh. The conclusion is, trying a semi-random delay
(there is delay after the EMI bypass change), the issue is fixed.
Another possible explanation is that we do not do the "simple memory
test" FSL does in their imx-bootlets (1000 R/W cycles to/from piece of
the memory, while also outputing something on the serial port). This
might have caused the similar delay in the imx-bootlets and therefore
they didn't need to add this explicitly.
For now, this seems good fix enough, but to me, whole that memory
init code in imx-bootlets is completely flunked and it'd need deeper
investigation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
FSL 2.6.35 kernel assumes that the bootloader passes the CONFIG_REVISION_TAG information.
The kernel uses this data to distinguish between Dialog versus mc34708 based boards,
and also to distinguish between revA and revB of the mc34708 based boards.
Suggested-by: Yu Li <yk@magniel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
types.h must be included in imx-regs.h if one wants to include
imx-regs.h in a board configuration file. That for one's part is
necessary, if one wants to use addresses defined in imx-regs.h.
For example, fsl_esdhc.c needs CONFIG_SYS_FSL_ESDHC_ADDR defined and
a proper thing is to define it with IMX_MMC_SDHCx_BASE in board
configuration file. This patch fixes the build in that case.
Signed-off-by: Timo Ketola <timo@exertus.fi>
Acked-by: Stefano Babic <sbabic@denx.de>
Defining CONFIG_FSL_ESDHC brings in a call to get_clocks, so let's
implement get_clocks function. This is how it seems to be implemented
elsewhere.
Signed-off-by: Timo Ketola <timo@exertus.fi>
Acked-by: Stefano Babic <sbabic@denx.de>
Init the core regulator voltage to 1.2V. This is required for the correct
functioning of the GPU and when the ARM LDO is set to 1.225V. This is a
workaround to fix some memory clock jitter.
Note: This should be but can't be done in the DCD. The bootloader
prevents access to the ANATOP registers.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Jason Chen <b02280@freescale.com>
CC: Jason Liu <r64343@freescale.com>
CC: Ranjani Vaidyanathan <ra5478@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <festevam@gmail.com>
This reverts commit 69d26d09de.
Apparently, this commit got mainline only because of out-of-tree
port and causes breakage on board that is mainline. Revert.
Reason:
* The OOT board has 512MB of DRAM, enabling this additional address
line enabled it to work fine with 512MB of RAM.
* Every mainline port has max. 256MB of DRAM, therefore this revert
has no impact on any mainline port
* Though this caused a problem with new M28 board with 256MB of DRAM
where the chips are wired differently. The patch-to-be-reverted
caused the DRAM to behave like this:
[128MB chunk #1][128MB chunk #1 again][128MB chunk #2][128MB chunk #2 again]
Therefore to retain the current one-memory-init-rules-them-all situation,
revert this patch until another board emerges and will actually be pushed
mainline that needs different setup.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Print CPU information within board_late_init().
This is in preparation for adding 1GHz support, which requires programming a PMIC
via I2C. As I2C is only available after relocation, print the CPU information
later at board_late_init(), so that the CPU frequency can be printed correctly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
mx5: Add clock config interface
Add clock config interface support, so that we
can configure CPU or DDR clock in the later init
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Eric Miao <eric.miao@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
get_ahb_clk() is a common function between mx5 and mx6.
Place it into imx-common directory.
Cc: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The MX53 SATA interface can use an internal clock (USB PHY1)
instead of an external clock. This is an undocumented feature, but used
on most Freescale's evaluation boards, such as MX53-loco.
As stated by Freescale's support:
Fuses (but not pins) may be used to configure SATA clocks.
Particularly the i.MX53 Fuse_Map contains the next information
about configuring SATA clocks :
SATA_ALT_REF_CLK[1:0] (offset 0x180C)
'00' - 100MHz (External)
'01' - 50MHz (External)
'10' - 120MHz, internal (USB PHY)
'11' - Reserved
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Add base address and MXC_SATA_CLK to return
the clock used for the SATA controller.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Dirk Behme <dirk.behme@de.bosch.com>
EXYNOS SoC platform has MIPI-DSI controller and MIPI-DSI
based LCD Panel could be used with it. This patch supports MIPI-DSI driver
based Samsung SoC chip.
LCD panel driver based MIPI-DSI should be registered to MIPI-DSI driver at
board file and LCD panel driver specific function registered to mipi_dsim_ddi
structure at lcd panel init function called system init.
In the MIPI-DSI driver, find lcd panel driver by using registered
lcd panel name, and then initialize lcd panel driver.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
This patch support EXYNOS FB and FIMD display drivers.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
To sets up lcd and mipi clock in EXYNOS display driver, added clock interface.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This is definitions of system registers and power mananagement registers for EXYNOS SoC.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
TZPC IP is common across Exynos based SoC'c. Renaming exynos5_tzpc
in arch/arm/include/asm/arch-exynos/tzpc.h to exynos_tzpc will allow generic
usase of tzpc.
Also modify board/samsung/smdk5250/tzpc_init.c to use exynos_tzpc.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Introduce a __weak misc_init_r function that just runs dieid_num_r().
Remove misc_init_r from cm_t35, mcx, omap3_logic and mt_ventoux as this was
all they did for misc_init_r.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
This rule confirms that if we're on ARM and we have enabled THUMB builds
that we have a new enough toolchain to produce a working binary.
Changes in v2:
- Switch to ALL-$(CONFIG_SYS_THUMB_BUILD) in arch/arm/config.mk (Mike F)
- Simplfy checkthumb test after doing the above
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Avoid using __attribute__ ((__packed__)) unless it's
absolutely necessary. "packed" will remove alignment
requirements for the respective objects and may cause
alignment issues unless alignment is also enforced
using a pragma.
Here, these packed attributes were causing alignment
faults in Thumb build.
Signed-off-by: Aneesh V <aneesh@ti.com>
Enable -march=armv7-a for armv7 platforms if the tool-chain
supports it. This in turn results in Thumb-2 code generated
for these platforms if CONFIG_SYS_THUMB_BUILD is enabled.
Signed-off-by: Aneesh V <aneesh@ti.com>
Enable Thumb build and ARM-Thumb interworking based on the new
config flag CONFIG_SYS_THUMB_BUILD
Signed-off-by: Aneesh V <aneesh@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Use ENTRY and ENDPROC with assembly functions to ensure
necessary assembler directives for all functions.
Signed-off-by: Aneesh V <aneesh@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This will add ARM specific over-rides for the defines
from linux/linkage.h
Signed-off-by: Aneesh V <aneesh@ti.com>
Tested-by: Mike Frysinger <vapier@gentoo.org>
Warm reset is not functional in case of omap5430ES1.0.
So override the weak reset_cpu function to use
cold reset instead.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The reset.S has the function to do a warm reset on OMAP
based socs. Moving this to a reset.c file so that this
acts a common layer to add any reset related functionality
for the future.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
PD_TIM bit field which specifies the power down timing is defined
to occupy bits 8-11, where as it is actually from 12-15 bits.
So correcting this.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Make the sysctrl structure common, so that it can
be used in generic functions across socs.
Also change the base address of the system control module, to
include all the registers and not simply the io regs.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The full internal SRAM of size 128kb is public in the case of OMAP5 soc.
So change the base address accordingly.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The different silicon revision variable names was defined for OMAP4 and
OMAP5 socs. Making the variable common so that some code can be
made generic.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The break statement is missing in init_omap_revision function, resulting
in a wrong revision identification. So fixing this.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The nominal opp vdd values as recommended for
ES1.0 silicon is set for mpu, core, mm domains using palmas.
Also used the right sequence to enable the vcores as per
a previous patch from Nishant Menon, which can be dropped now.
http://lists.denx.de/pipermail/u-boot/2012-March/119151.html
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The OMAP5 silicon has new DDR PHY design, which includes a external PHY
as well. So configuring the ext PHY parameters here. Also the EMIF timimg
registers and a couple of DDR mode registers needs to be updated based on
the testing from the actual silicon.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The control module provides options to set various signal
integrity parameters like the output impedance, slew rate,
load capacitance for different pad groups. Configure these
as required for the omap5430 sevm board.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Aligning all the clock related settings like the dpll frequencies, their
respective clock outputs, etc to the ideal values recommended for
OMAP5430 ES1.0 silicon.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
OMAP4 requires that parent domains scale ahead of dependent domains.
This is due to the restrictions in timing closure. To ensure
a consistent behavior across all OMAP4 SoC, ensure that
vdd_core scale first, then vdd_mpu and finally vdd_iva.
As part of doing this refactor the logic to allow for future
addition of OMAP4470 without much ado. OMAP4470 uses different
SMPS addresses and cannot be introduced in the current code
without major rewrite.
Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
TPS SET0/SET1 register is selected by a GPIO pin on OMAP4460 platforms.
Currently we control this pin with a mux configuration as part of
boot sequence.
Current configuration results in the following voltage waveform:
|---------------| (SET1 default 1.4V)
| --------(programmed voltage)
| <- (This switch happens on mux7,pullup)
vdd_mpu(TPS) -----/ (OPP boot voltage)
--------- (programmed voltage)
vdd_core(TWL6030) -----------------------/ (OPP boot voltage)
Problem 1) |<----- Tx ------>|
timing violation for a duration Tx close to few milliseconds.
Problem 2) voltage of MPU goes beyond spec for even the highest of MPU OPP.
By using GPIO as recommended as standard procedure by TI, the sequence
changes to:
-------- (programmed voltage)
vdd_mpu(TPS) ------------/ (Opp boot voltage)
--------- (programmed voltage)
vdd_core(TWL6030) -------------/ (OPP boot voltage)
NOTE: This does not attempt to address OMAP5 - Aneesh please confirm
Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
OMAP Voltage controller is used to generically talk to
PMICs on OMAP3,4,5 over I2C_SR. Instead of replicating code
in multiple SoC code, introduce a common voltage controller
logic which can be re-used from elsewhere.
With this change, we replace setup_sri2c with omap_vc_init which
has the same functionality, and replace the voltage scale
replication in do_scale_vcore and do_scale_tps62361 with
omap_vc_bypass_send_value. omap_vc_bypass_send_value can also
now be used with any configuration of PMIC.
NOTE: Voltage controller controlling I2C_SR is a write-only data
path, so no register read operation can be implemented.
Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Add parameters to the OMAP MMC initialization function so the board can
mask host capabilities and set the maximum clock frequency. While the
OMAP supports a certain set of MMC host capabilities, individual boards
may be more restricted and the OMAP may need to be configured to match
the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example.
Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
This change adds an implementation of high-speed UART found on NXP
LPC32X0 SoCs. Such UARTs are enumerated as UART1, UART2 and UART7.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
This change adds initial support for NXP LPC32x0 SoC series.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
In driver mmc, generic s5p_sdhci code is implemented.
s5p_mmc file is dupulicated.
we are good that use the generic sdhci.
This patch supported the sdhci for Samsung-SoC.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Lei Wen<leiwen@marvell.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
* 'master' of git://git.denx.de/u-boot-i2c:
i2c:designware Turn off the ctrl when setting the speed
i2c: Add support for designware i2c controller
sh: i2c: Add support I2C controller of SH7734
* 'marex@denx.de' of git://git.denx.de/u-boot-staging:
CMD: CONFIG_CMD_SETECPR -> CONFIG_CMD_SETEXPR on omap3_logic
CMD: Fix CONFIG_CMD_SAVEBP_WRITE_SIZE -> CONFIG_CMD_SPL_WRITE_SIZE
CMD: Fix typo CMD_FSL -> CMD_MFSL in readme
HWW1U1A: Fix CMD_SHA1 -> CMD_SHA1SUM
CMD: Remove CMD_LOG, it's unused
CMD: Fix typo KGBD -> KGDB on debris board
CMD: Drop CONFIG_CMD_EMMC, it's not used
CMD: Drop CONFIG_CMD_DFL, it's not used
CMD: Drop CMD_DCR, it's not used
CMD: Drop CMD_CAN, it's not used
CMD: Remove CMD_AUTOSCRIPT, it's not used
AT91: Drop AT91_SPIMUX command from cmd_all
Earlier, a driver exists in the u-boot source for designware i2c interface. That
driver was specific to spear platforms. This patch implements the i2c controller
as a generic driver which can be used by multiple platforms
The driver files are now renamed to designware_i2c.c and designware_i2c.h and
these are moved into drivers/i2c folder for reusability by other
platforms
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Commit 0a672d4 "arm: Add Prep subcommand support to bootm" re-organized
do_bootm_linux for ARM. During the re-organization, the call to
fdt_fixup_ethernet() was removed. I assume this was useful, so add it
back.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tom Rini <trini@ti.com>
Commit 0a672d4 "arm: Add Prep subcommand support to bootm" re-organized
do_bootm_linux() for ARM. During the re-organization, the code to pass
the device tree to the kernel was removed. Add it back. This restores
the ability to boot a kernel using device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Allen Martin <amartin@nvidia.com>
Tested-by: Allen Martin <amartin@nvidia.com>
We certainly don't want the compiler to reorganise the code for dcache flushing.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Stefano Babic <sbabic@denx.de>
As well as pushed for ARM926EJS, we certainly don't want
the compiler to reorganise the code for dcache flushing
Fix checkpatch warnings as well.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Marek Vasut <marex@denx.de>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
Freescale SOCs require an header to u-boot.bin
The patch adds u-boot.imx to the default targets
if the imx file is set (IMX_CONFIG).
Signed-off-by: Stefano Babic <sbabic@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
CC: Loïc Minier <loic.minier@linaro.org>
CC: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Tested-by: Dirk Behme <dirk.behme@googlemail.com>
This fixes the issue where mxs_dma_init() was called either twice or never,
without introducing any new init hooks.
The idea is to allow each and every device using the APBH DMA block to
configure and request only the channels it uses, instead of making it call init
for all the channels as is now.
The common DMA block init part, which only configures the block, is then called
from CPUs arch_cpu_init() call.
NOTE: This patch depends on:
http://patchwork.ozlabs.org/patch/150957/
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Misaligned warnings are useful to debug faulty drivers.
A misaligned warning is printed also when the driver
is correct - use debug() instead of printf().
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
CC: Mike Frysinger <vapier@gentoo.org>
CC: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Since commit 5c1ad3e6f8
(net: fec_mxc: allow use with cache enabled) the FEC_MXC
driver uses flush_dcache_range() and invalidate_dcache_range()
functions. This driver is also configured for ARM1136 based
'flea3' and 'mx35pdk' boards which currently do not build
as there are no ARM1136 specific flush_dcache_range() and
invalidate_dcache_range() functions. Add various ARM1136
cache functions to fix building for 'flea3' and 'mx35pdk'.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
CC: Mike Frysinger <vapier@gentoo.org>
CC: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
This command boots Linux zImage from where the zImage is loaded to. Passing
initrd and fdt is supported.
Tested on i.MX28 based DENX M28EVK
Tested on PXA270 based Voipac PXA270.
NOTE: This currently only supports ARM, but other architectures can be easily
added by defining bootz_setup().
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Warren <TWarren@nvidia.com>
Cc: albert.u.boot@aribaud.net
Cc: afleming@gmail.com,
Cc: Simon Glass <sjg@chromium.org>,
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Each cpu directory currently has its own .lds file. This is only needed
in most cases because the start.o file is in a different subdir.
Now that we can factor out this difference, we can move most cpus over
to the common .lds file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most ARM CPUs use a very similar link script. This adds a basic
script that can be used by most CPUs.
Two new symbols are introduced which are intended to eventually be
defined on all architectures to make things easier for generic relocation
and reduce special-case code for each architecture:
__image_copy_start is the start of the text area (equivalent to the
existing _start on ARM). It marks the start of the region which must be
copied to a new location during relocation. This symbol is called
__text_start on x86 and microblaze.
__image_copy_end is the end of the region which must be copied to a new
location during relocation. It is normally equal to the start of the BSS
region, but this can vary in some cases (SPL?). Making this an explicit
symbol on its own removes any ambiguity and permits common code to always
do the right thing.
This new script makes use of CPUDIR, now defined by both Makefile and
spl/Makefile, to find the directory containing the start.o object file,
which is always placed first in the image.
To permit MMU setup prior to relocation (as used by pxa) we add an area
to the link script which contains space for this. This is taken
from commit 7f4cfcf. CPUs can put the contents in there using their
start.S file. BTW, shouldn't that area be 16KB-aligned?
Signed-off-by: Simon Glass <sjg@chromium.org>
This is set by the top level Makefile anyway, so drop it. This does
have the effect of changing the order - now the board link script will
have preference over the CPU one. But this seems more correct anyway.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix:
clocks-common.c: In function 'setup_non_essential_dplls':
clocks-common.c:323:6: warning: variable 'sys_clk_khz' set but not used
[-Wunused-but-set-variable]
clocks-common.c: In function 'setup_non_essential_dplls':
clocks-common.c:323:6: warning: variable 'sys_clk_khz' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Tom Rini <trini@ti.com>
Add basic i2c driver for Tegra2 with 8- and 16-bit address support.
The driver requires CONFIG_OF_CONTROL to obtain its configuration
from the device tree.
(Simon Glass: sjg@chromium.org modified for upstream)
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add U-Boot's peripheral clock information to the Tegra20 device tree file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
I2C ports have a 16-bit clock divisor. Add code to handle this special
case so that I2C speeds below 150KHz are supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Change this name to fit with the current convention in the Tegra
header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
When using CONFIG_OF_CONTROL, add a check that we have a valid FDT
and panic() if not. This must be done after the console is ready.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This adds basic support for the Tegra2 USB controller. Board files should
call board_usb_init() to set things up.
Configuration is performed through the FDT, with aliases used to set the
order of the ports, like this fragment:
aliases {
/* This defines the order of our USB ports */
usb0 = "/usb@0xc5008000";
usb1 = "/usb@0xc5000000";
};
drivers/usb/host files ONLY: Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
A common requirement is to find the clock ID for a peripheral. This is the
second cell of the 'clocks' property (the first being the phandle itself).
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This adds clock references to the USB part of the device tree for U-Boot,
and marks USB1 as supporting legacy mode (which we disable in the driver).
The USB timing information may vary between boards sometimes, but for
now we hard-code it in C. This is because all current T2x boards use
the same values, we will deal with T3x later and we first need to agree
on the format for this timing information in the fdt and may in fact
decide that it has no place there.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This adds a basic binding for the oscillator and peripheral clocks. The
second cell is the clock number, defined as the bit number within the clock
enable register if the peripheral clock.
This uses the RFC clock bindings from Grant Likely so may change later:
https://lkml.org/lkml/2011/12/12/498
It is taken from Stephen Warren's patch here:
http://patchwork.ozlabs.org/patch/141359/
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This was taken from commit b48c54e2 at:
git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra.git
config.mk is updated to provide this file to boards through the
built-in mechanism:
/include/ ARCH_CPU_DTS
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This was taken from commit b48c54e2 at:
git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra.git
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The 4.2.2 gcc in the ELDK42 release doesn't like the direct SP
load using a constant in tegra2_start. Change it to use a load
thru another reg using mov sp, %0 : : "r"(CONST).
Tested on my Seaboard T20-A03, U-Boot loads and runs OK. Also
compiled all tegra2 builds with both gcc 4.2.2 and 4.4.1 OK.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Implement reset for highbank platform. Reset is triggered via a wfi
instruction, so enabling armv7 for the compiler is necessary.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
udelay calls were off due to failing to convert us to ns. Fix this and drop
the unnecessary shifts since NS_PER_TICK is only 7ns.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The get_tbclk function was missing and the recent commit "common: add
possibility for readline_into_buffer timeout" makes it required.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Add exynos4_dmc structure in dmc.h for exynos4 dram controllor(DMC).
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch fixes the s3c24x0 timer code to work with the ARM
relocation feature.
Signed-off-by: David Mueller <d.mueller@elsoft.ch>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adds prep subcommand to bootm implementation of ARM. When bootm is called
with the subcommand prep the function stops right after ATAGS creation and
before announce_and_cleanup.
This is used in command "cmd_spl export"
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Simon Schwarz <simonschwarzcor@gmail.com>
Call i2c initialization in spl_board_init only if I2C
is configured for the board.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Simon Schwarz <simonschwarzcor@gmail.com>
This only outputs "Assuming u-boot.bin..." if debug is active.
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>
This adds Linux booting to the SPL
This depends on CONFIG_MACH_TYPE patch by Igor Grinberg
(http://article.gmane.org/gmane.comp.boot-loaders.u-boot/105809)
Related CONFIGs:
CONFIG_SPL_OS_BOOT
Activates/Deactivates the OS booting feature
CONFIG_SPL_OS_BOOT_KEY
defines the IO-pin number u-boot switch - if pressed u-boot is
booted
CONFIG_SYS_NAND_SPL_KERNEL_OFFS
Offset in NAND of direct boot kernel image to use in SPL
CONFIG_SYS_SPL_ARGS_ADDR
Address where the kernel boot arguments are expected - this is
normaly RAM-begin + 0x100
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>
Linux crashes if the GPMC isn't configured for the dm9000.
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>
This implements booting of Linux from NAND in SPL
Related config parameters:
CONFIG_SYS_NAND_SPL_KERNEL_OFFS
Offset in NAND of direct boot kernel image to use in SPL
CONFIG_SYS_SPL_ARGS_ADDR
Address where the kernel boot arguments are expected - this is
normally RAM-start + 0x100 (on ARM)
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>
Change the parent UART clock to be PLL2, so that U-boot can also boot
a Freescale 2.6.35 kernel for mx53.
FSL kernel and U-boot changed the UART parent from PLL3 to PLL2 to avoid
conflicts with IPU clocks, so that the video resolution can be changed
without affecting the UART clock.
On a 2.6.35 kernel the serial console is messed up after IPU driver is loaded
and this patch fixes this problem.
Tested on a mx53loco board booting a FSL kernel and also a mainline kernel.
Reported-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Instead of hardcoding the mx6 silicon revision, read it in run-time.
Also, besides the silicon version print the mx6 variant type: quad,dual/solo
or solo-lite.
Tested on a mx6qsabrelite, where it shows:
CPU: Freescale i.MX6Q rev1.0 at 792 MHz
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <r64343@freescale.com>
Instead of compiling the function and using the result as a constant, simply use
the constant.
NOTE: This patch works around bug:
http://gcc.gnu.org/bugzilla/show_bug.cgi?id=52546
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cut down the VDDIO/VDDA regulator stabilization delays to 500 uS. That should be
enough according to the datasheet and bootlets.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Robert Deliën <robert@delien.nl>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
After booting mx6qsabrelite from POR the following is reported:
CPU: Freescale i.MX61 family rev1.0 at 792 MHz
Reset cause: unknown reset
This is because both the POR and WDOG bits are set after reset.
Fix this by also checking both bits in the POR case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Enables all fourteen address lines for DRAM
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
The GPIO_INT_ACT_LOW_SET was incorrectly handling interrupt lines higher than 7.
This is due to the fact that there are two registers for total of 16 lines.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>
IxEthAcc.c: In function ‘ixEthAccInit’:
IxEthAcc.c:105:21: warning: comparison between ‘IxEthDBStatus’ and ‘enum <anonymous>’ [-Wenum-compare]
IxEthDBAPISupport.c: In function ‘ixEthDBPortAddressSet’:
IxEthDBAPISupport.c:633:18: warning: variable ‘ackPortAddressLock’ set but not used [-Wunused-but-set-variable]
IxQMgrDispatcher.c: In function ‘ixQMgrLLPShow’:
IxQMgrDispatcher.c:1194:18: warning: variable ‘q’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>
Add -EB flag to LD to switch endianness of the linker. This should make armeb
targets buildable again. Also, make use of U-Boot's internal libgcc instead of
toolchain's one, this works around the use of libraries from GCC, which might be
little endian.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>
Adds support for loading U-Boot from UART using YMODEM protocol.
If YMODEM support is enabled in SPL and the romcode indicates
that SPL loaded via UART then SPL will wait for start of a
YMODEM transfer via the console port.
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This patch fixes erroneous 32-bit access to registers
hw_clkctrl_frac0 and hw_clkctrl_frac1.
Signed-off-by: Robert Delien <robert@delien.nl>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
This patch introduces an 8-bit register, mx28_register_8, in order to
prepare for fixing erroneous 32-bit wide access of registers
hw_clkctrl_frac0 and hw_clkctrl_frac1.
Signed-off-by: Robert Delien <robert@delien.nl>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
This patch renames mx28_register to mx28_register_32 in order to
prepare for the introduction of an 8-bit register, mx28_register_8.
Signed-off-by: Robert Delien <robert@delien.nl>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
This patch replaces the use of magice numbers for scratch register
addresses with earlier defined register definitions.
Signed-off-by: Robert Delien <robert@delien.nl>
Common code has a mdelay() func, so use that instead of the usb-specific
wait_ms() func. This also fixes the build errors:
ohci-hcd.c: In function 'submit_common_msg':
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1519:9: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1816:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1827:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1844:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1563:11: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1583:9: sorry, unimplemented: called from here
make[1]: *** [ohci-hcd.o] Error 1
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Marek Vasut <marex@denx.de>
Add calls to bootstage before and after relocation, and just
before jumping to the OS.
The idea here is you can call bootstage_report() to get a report.
Additionally, if you define CONFIG_BOOTSTAGE_REPORT then a report is
printed automatically by U-Boot just before jumping to the kernel.
Signed-off-by: Simon Glass <sjg@chromium.org>
These calls should not be made directly any more, since bootstage
will call the show_boot_...() functions as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
This changes the number 15 as used in boot_stage_progress() to use the
new name provided for it. This is a separate patch because it touches
so many files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
All boards are using the gen_atmel_mci driver now, so no need
to carry the old driver around.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Boards can select either the 'built-in' parser or the hush parser. We
should not call builtin_run_command() if we are using the hush parser.
We use run_command() instead, since it knows how to call the correct
parser.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The current run_command() is only one of the parsing options - the other
is hush. We should not call run_command() when the hush parser is being
used. So we rename this function to better explain its purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Mainline kernel for OMAP3 doesn't enable L2 cache
It expects L2$ to be enabled by ROM-code/bootloader.
Leaving L2$ enabled can be troublesome in cases where
the L2 cache is not under CP15 control, such as in
Cortex-A9. This problem is explained in detail in
the commit dc7100f408
However, this problem doesn't apply to Cortex-A8
because L2$ in Cortex-A8 is under CP15 control and
hence the generic armv7 maintenance opertions work
for it.
As such we can make an exception for OMAP3 and
leave the L2$ enabled when we jump to kernel. This
is done by removing the strongly-linked implementation
of v7_outer_cache_disable() and allowing it to fall
back to the weakly linked implementation that doesn't
do anything.
Signed-off-by: Aneesh V <aneesh@ti.com>
The video setup for the Epson display is provided. Addtionally
some extra info is displayed next to the Linux logo.
Make get_cpu_rev() publicly available (added to sys_proto.h).
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
In commit 2d575e4685 a separate header
file was introduced for the DM6467T EVM, include/configs/davinci_dm6467Tevm.h.
The substantial difference between the davinci_dm6467evm and the
davinci_dm6467Tevm configuration is a single bit in the hardware revision
that is passed to the Linux kernel and davinci_dm6467evm has
REFCLK_FREQ = 27000000 where as davinci_dm6467Tevm.h has a
REFCLK_FREQ = 33000000.
This patch removes include/configs/davinci_dm6467Tevm.h. Instead the
include/configs/davinci_dm6467evm.h configuration is used for DM6467T EVMs and
renamed CFG_REFCLK_FREQ to CONFIG_REFCLK_FREQ and CONFIG_REFCLK_FREQ is defined
in boards.cfg.
Signed-off-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Cc: Tom Rini <trini@ti.com>
* For cold silicon the DDR timings need to be relaxed in order for
the device to boot with DDR at 266MHz
* Fix proposed by James Doublesin
Signed-off-by: Chase Maupin <Chase.Maupin@ti.com>
check for the return status for eth_getenv_enetaddr_by_index()
and eth_setenv_enetaddr() functions and print appropriate message
on failure.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
get_reset_cause() function is only used inside print_cpuinfo(), so let it be
defined only when CONFIG_DISPLAY_CPUINFO is selected.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <jason.hui@linaro.org>
Move (E)CSPI register declarations into the imx-regs.h files for each supported CPU
Introduce two new macros to control conditional setup
MXC_CSPI - Used for processors with the Configurable Serial Peripheral Interface (MX3x)
MXC_ECSPI - For processors with Enhanced Configurable... (MX5x, MX6x)
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <jason.hui@linaro.org>
Tested-by: Jason Liu <jason.hui@linaro.org>
The interface to the mxc_gpio driver uses integer (ordinal) values to
refer to all GPIOs on the i.MX processors. The registers themselves
and much of the i.MX documentation are banked in groups of 32, and these
macros allow the use of the port:index numbering for clarity.
GPIO_NUMBER() converts to ordinal value from port:index
GPIO_PORT() returns the port of an ordinal value
GPIO_INDEX() returns the index or offset of the ordinal.
Discussion on the mailing list at
http://lists.denx.de/pipermail/u-boot/2012-January/116927.html
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
This patch fixes booting i.MX28 CPUs via USB download.
In this mode the CPU's bootrom implements a USB HID device that
accepts a bootstream.
When downloading the bootstream via USB, first the SPL code is
received and executed. Then the u-boot image is received and
called.
The USB bootmode is interrupt driven.
This patch fixes two things:
1) The ARM's fast interrupt mode is disabled when the SPL code
has been run. So save and restore the CPSR register.
2) Save and restore c1 control register: the exception vector
location needs to be set back to bootrom space to make the USB
interrupts work again. The SPL code needs to change this
option for the ram size probing.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
The DC power STS shouldn't be checked if booting off 5V supply.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Robert Deliën <robert@delien.nl>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
commit f31a911fe (arm, post: add missing post_time_ms for arm)
enables get_ticks and get_tbclk for all arm based boards,
MX5/MX6 have not yet implemented.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Dirk Behme <dirk.behme@de.bosch.com>
CC: Jason Liu <jason.hui@linaro.org>
CC: Marek Vasut <marek.vasut@gmail.com>
commit f31a911fe (arm, post: add missing post_time_ms for arm)
enables get_ticks and get_tbclk for all arm based boards,
MX5/MX6 have not yet implemented.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Before we can send a command we need both the DATI (command inhibit on
mmc_dat line) bit and CMDI (command inhibit on mmc_cmd line) are clear.
The previous behavior of only checking on DATI was insufficient on some
cards and incorrect behavior in any case. This makes the code check
for both bits being clear and makes the error print more clear as
to what happened. DATI_CMDDIS is removed as it was unused elsewhere
in the code and stood for 'DATI is set, cmds are disabled still'.
Fix originally spotted by Peter Bigot.
Tested-by: Peter A. Bigot <bigotp@acm.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Andreas Müller <schnitzeltony@googlemail.com>
This patch moves hawkboard to the new spl infrastructure from the
older nand_spl one.
Removed the hawkboard_nand_config build option -- The spl code now
gets compiled with hawkboard_config, after building the main u-boot
image, using the CONFIG_SPL_TEXT_BASE. Modified the README.hawkboard
to reflect the same.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
The V bit of the c1 register of CP15 should not be cleared on DA850
SoCs since they have no valid memory at 0x00000000. This patch
introduces a configuration option CONFIG_SYS_EXCEPTION_VECTORS_HIGH
that allows setting the correct value for the V bit.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Reported-by: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
The current implementation invalidates the data cache before turning it
off and causes problems on the hawkboard. See the discussion in
http://lists.denx.de/pipermail/u-boot/2012-January/115212.html
According to the ARM926EJ-S Technical Reference Manual, the cache should
be flushed instead.
Also fix the comments to match code.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Rebased and corrected commit message.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
This patch reverts commit ca4b55800e
"arm, arm926ejs: always do cpu critical inits" since it impacts all
arm926ejs based configurations and caused problems, e.g., with
the hawkboard.
Instead the patch removes the CONFIG_SKIP_LOWLEVEL_INIT defines
from the board configurations that need low level initialization.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
The low level initialization code in
arch/arm/cpu/arm926ejs/davinci/lowlevel_init.S was written for
DM644X SoCs only. This patch makes the lowlevel_init function in this
file a dummy function for SoCs other than DM644X.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Tom Rini <trini@ti.com>
Cc: Sergey Kubushyn <ksi@koi8.net>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
ACTIM_CTRLA macro errently passes "b" parameter to ACTIM_CTRLA_TRAS()
instead of "c". To make usage more clear, replace all single-letter
macro parameters with more descriptive parameter names.
Signed-off-by: Peter Barada <peter.barada@logicpd.com>
We do not have thermal management or Smartreflex
enabled at U-Boot level. So, it's better to stick
to OPP100 for MPU instead of the OPP Turbo that is
used now. Adjust the VDD_MPU accordingly.
Tested-by: Sebastien Jan <s-jan@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
add support for printing various clock frequency info found
in SOC such as ARM core frequency, DSP core frequency and DDR
frequency as part of bdinfo command.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Tom Rini <trini@ti.com>
remove the macro CONFIG_DISPLAY_CPUINFO as it is no longer
required. This is because clock info will be printed as part
'bdinfo' command and also remove support print_cpuinfo() as it will
no longer be called.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Tom Rini <trini@ti.com>
AM3517: Changed default clock rate for AM3517
Changed #define MPU_M_13_ES2 from 0x1F4 to 0x258, this allows
the AM3517 to boot up at 600MHz instead of 500 MHz
Signed-off-by: Schuyler Patton <spatton@ti.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
usb dpll configuration is done only part of non-essential
dppl configuration however if CONFIG_USB_EHCI_OMAP is defined
we may have to configure usb dpll's for proper functioning
of usb modules. So move the usb dppl configuration to a new func.
and utilise the same during essential dpll configuration.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Adding ehci clock enabling mechanism part of clock framework.
When essential clocks are enabled during init phase usb host
clocks can also be enabled from clock framework.
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Clean up added ehci-omap.c and make it generic for re-use across
omap-soc having same ehci ip block. Also pass the modes to be configured
from board file and configure the ports accordingly. All usb layers
are not cache aligned, till then keep cache off for usb ops as ehci will use
internally dma for all usb ops.
* Add a generic common header ehci-omap.h having common ip block
data and reg shifts.
* Rename and modify ehci-omap3 to ehci.h retain only conflicting
sysc reg shifts remove others and move to common header file.
* pass the board data for beagle/panda accordinly to use
ehci ports.
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Samsung's ARM Cortex-A15 based SoCs are known as Exynos5 series of
SoCs. This patch adds the support for Exynos5.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
CONFIG_SYS_CLK_FREQ_C210 macro giving notion of S5PC2XX (Exynos4)
architecture. Replace CONFIG_SYS_CLK_FREQ_C210 with CONFIG_SYS_CLK_FREQ
to make it generic for exynos architecture.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds support the generic watchdog timer for s5pc1xx and exynos4
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: HeungJun, Kim <riverful.kim@samsung.com>
This patch adds power.h and SAMSUNG_BASE() macro for using Exynos4 power.
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch add watchdog.h for Exynos4
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Earliar ARM clock frequency was calculated by:
MOUTAPLL/(DIVAPLL + 1) which is actually returning SCLKAPLL.
It is fixed by calculating it as follows:
ARMCLK=MOUTCORE / (DIVCORE + 1) / (DIVCORE2 + 1)
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add TCMPB3 field in pwm structure, earliar this was res1.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
after http://patchwork.ozlabs.org/patch/136415/ was applied. All Marvell
build fails with below error
common/libcommon.o: In function `cread_line':
/home/uboot/src/u-boot-arm/common/main.c:717: undefined reference to `get_ticks'
/home/uboot/src/u-boot-arm/common/main.c:717: undefined reference to `get_tbclk'
/home/uboot/src/u-boot-arm/common/main.c:720: undefined reference to `get_ticks'
The same is fixed for Kirkwood, ARMADA100, pantheon and orion5x SoCs
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
The decompressor expects the L2 cache to be disabled. This fixes booting
some kernels, which have CONFIG_ARM_PATCH_PHYS_VIRT enabled.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Wolfgang Denk <wd@denx.de>
FEC does not work on the i.mx51/53evk board, it will hangup
In: serial
Out: serial
Err: serial
Net:
After bisect, it due to the following commit:
be252b6 net: imx: Add multi-FEC support for imx_get_mac_from_fuse
has change the imx_get_mac_from_fuse fucntion prototype, but fail
to update i.mx5, here it does it.
After apply this patch, u-boot works again on i.mx51/53 evk boards.
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Showing CPU frequency during boot is useful information.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This patch modifies mxcmmc.c to be used
not only by i.MX27 but also by i.MX31 boards.
Both use the same SD controller, but have different
clock set-ups.
The i.MX27 imx_get_XXXclock functions are made static to
generic.c and a public mxc_get_clock() function
is provided. Pins, base address and prototypes for
an i.MX31 specific board_init_mmc() are provided.
Some of the i.MX27 clock getters are unused and marked
as such to avoid warnings (./MAKEALL -s mx27), but
the code was left in for future use.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Acked-by: Stefano Babic <sbabic@denx.de>
The uart txd pad can also provide the rxd function. But it does not stop its
tx role. This could be used for a half duplex serial port.
Change names to reduce confusion.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Jason Liu <jason.hui@linaro.org>
CC: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <jason.hui@linaro.org>
The Buffer Logic of VPSS is Not Reset by System Reset Pin, see
http://www.ti.com/lit/er/sprz316b/sprz316b.pdf chapter Advisory 1.2.1
on page 9. Add workaroundcode proposed in the errata.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Tom Rini <tom.rini@gmail.com>
In 8775471bb, the call to timer_init() was removed from common code
and put in OMAP3 s_init() function. As a result the boot was broken
on OMAP4. This patch adds timer_init() in OMAP4 s_init(), that fix
boot on all OMAP4 boards.
Signed-off-by: Nicolas Dechesne <n-dechesne@ti.com>
Tested-by: Robert P. J. Day <rpjday@crashcourse.ca>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Tom Rini <trini@ti.com>
The function get_sdr_cs_offset reads the CS_CFG register in the SDRC
to determine where CS1 is mapped to. make_cs1_contiguous() will set
CS1 to follow after CS0. The CS_CFG register has values in bits 9:8
and 3:0 but we had erroneously been testing 5:4 and 3:0 resulting in
incorrect offsets on platforms with less than 128MB as 3:0 describe
128MB hunks and 9:8 describe 32MB offsets after the 128MB hunk.
Tested-by: Grant Erickson <marathon96@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
