Add initial support for Rock PI 4 board.
Specification
- Rockchip RK3399
- LPDDR4
- eMMC
- SD card slot
- RTL8211E 1Gbps
- HDMI In/Out, DP, MIPI DSI/CSI
- PCIe M.2
- USB 2.0, USB-3.0
- USB C Type
Commit details of rk3399-rock-pi-4.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: add ROCK Pi 4 DTS support"
(sha1: 1b5715c602fda7b812af0e190eddcce2812e5417)
Signed-off-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add initial support for Rockpro64 board.
Specification
- Rockchip RK3399
- 2/4GB Dual-Channel LPDDR3
- SD card slot
- eMMC socket
- 128Mb SPI Flash
- Gigabit ethernet
- PCIe 4X slot
- WiFI/BT module socket
- HDMI In/Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- DC 12V/2A
Commit details of rk3399-rockpro64.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: rockpro64 dts add usb regulator"
(sha1: 6db644c79c8d45d73b56bc389aebd85fc3679beb)
'Akash' has sent an initial patch before, so I keep him as board
maintainer and I'm co-maintainer based on our conversation.
Signed-off-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For bcm7445 and bcm7260, this patch enables CONFIG_DM_MMC and updates
the bcmstb SDHCI driver to use the new driver model. This allows
removal of SDHCI configuration handling from bcmstb.c, and eliminates
a board removal compile warning.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Heiko Schocher <hs@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
NAND: BUG at drivers/mtd/nand/raw/nand_base.c:4361/nand_scan_tail()!
This board has a NAND flash enabled, and it requires the HW PMECC in order
to correctly probe this flash.
In the NAND flash configuration , this is selected by the GENERATE_PMECC_HEADER
which is not needed for mmc configuration.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Several drivers used by the ControlCenterDC board were converted to DM
upstream. But the board had not been using these drivers yet.
Update the board's config file to reflect these changes and use the DM
version of these drivers. No further device tree updates are necessary,
since the devices in question are already present in the device tree.
This especially fixes the three compile warnings about CONFIG_DM_MMC,
CONFIG_DM_USB, and CONFIG_AHCI for the ControlCenterDC board.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables CONFIG_BLK and CONFIG_DM_MMC on helios4 to remove
these compile warnings:
===================== WARNING ======================
This board does not use CONFIG_DM_MMC. Please update
the board to use CONFIG_DM_MMC before the v2019.04 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dennis Gilmore <dgilmore@redhat.com>
- Gen3 PCIe driver + enablement on Salvator-X platforms.
- Gen3 recovery SPL used to reload ATF/OpTee/U-Boot instead of minimon.
- SDHI HS400 fixes ported from latest BSP and datasheet.
Move the main symbol for Freescale Fman Ethernet controller option to
Kconfig. Also migrate the CONFIG_SYS_QE_FMAN_FW_IN_xxx macros and
rename the SPIFLASH one to follow the same format as all of the others.
To do this fully we need to migrate CONFIG_QC, do so.
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable sound output. With this, 'sound play 1000 400' emits a simple beep.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable CONFIG_USE_PREBOOT on for the gardena mt7688 platforms, so that
this feature can be used here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch enables the "wdt" command, which is quite useful for watchdog
testing.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds CONFIG_DM_SPI for all m68k boards using
the cf_spi.c driver (DSPI module).
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Enable DT usage for all m68k boards. To provide a
working single binary, the dts has been kept as embedded.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
This patch adds basic dts files for all the m68k boards.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
[trini: Add CONFIG_TARGET_M5329EVB dtbs and update M5329EVB defconfigs]
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable eSDHC, SATA and USB DM for T2080QDS in uboot
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
CONFIG_PMECC_CAP has a higher priority than its ONFI detected
parameter and will overwrite it when defined. As per commit
49ad40298c, CONFIG_PMECC_CAP has a default value of 2 if not
otherwise stated. This results in the overwriting of the ONFI ECC
bits value. The following errors are seen when booting the kernel
from the nand flash:
Loading Environment from NAND... PMECC: Too many errors
NAND read from offset 140000 failed -74
*** Warning - some problems detected reading environment; recovered successfully
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: eth0: ethernet@f8008000
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x180000, size 0x80000
PMECC: Too many errors
NAND read from offset 180000 failed -74
0 bytes read: ERROR
NAND read: device 0 offset 0x200000, size 0x600000
PMECC: Too many errors
NAND read from offset 200000 failed -74
0 bytes read: ERROR
Bad Linux ARM zImage magic!
Fix it by setting the right value for ECC bits.
Fixes: 49ad40298c ("ARM: at91: Convert SPL_GENERATE_ATMEL_PMECC_HEADER to Kconfig")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
LS1028A is an ARMv8 implementation. LS1028ARDB is an evaluation
platform that supports the LS1028A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Update mtd-id for QSPI nor due to change introduced in mtd/spi in
linux 5.0. commit 84d043185dbe
("spi: Add a driver for the Freescale/NXP QuadSPI controller")
This modification is only for linux kernel version >= 5.0. To use
bootargs for kernel < 5.0, use the following bootargs
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0
earlycon=uart8250,mmio,0x21c0500
mtdparts=1550000.quadspi:2m(uboot),14m(free)"
CONFIG_MTDPARTS_DEFAULT="mtdparts=1550000.quadspi:2m(uboot),14m(free)"
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Build an SPL which can be started via SCIF download mode on R-Car Gen3
and allows loading and executing U-Boot uImage with the next stage code.
This is also useful for starting e.g. ATF BL2, which inits the hardware
and returns to the U-Boot SPL, which can then load e.g. U-Boot proper.
The H3, M3-W, M3-N SoCs have plenty of SRAM for storing the U-Boot SPL
while the payload, e.g. ATF BL2, executes, so there is no problem here.
However, E3 and D3 have much less SRAM, hence the loader uses a trick
where it copies itself beyond the area used by BL2 and executes from
there. That area is 32kiB large and not enough to hold U-Boot SPL, BSS,
stack and malloc area, so the later two are placed at +0x4000 offset
from start of SRAM, another area not used by ATF BL2. To make things
even more complicated, the SCIF loader cannot load to the upper 32kiB
of the SRAM directly, hence the copying approach.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
when loading the splash image from a FIT
- updates for loading internal and external splash data from FIT
- DM_GPIO/DM_VIDEO migration for mx53 cx9020 board
- fix boot issue on mx6sabresd board after DM_VIDEO migration
- increase the max preallocated framebuffer BPP to 32 in ipuv3
driver to prepare for configurations with higher color depth
- allow to use vidconsole_put_string() in board code for text
output on LCD displays
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXOK5Sw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXBvoAJ96YrInVKKWtuVigA9lNpk5xbmbeQCdG9wML4LI
dBbQyzD3mNqvnDMyNPQ=
=Plt7
-----END PGP SIGNATURE-----
Merge tag 'video-for-2019.07-rc3' of git://git.denx.de/u-boot-video
- update for using splashfile instead of location->name
when loading the splash image from a FIT
- updates for loading internal and external splash data from FIT
- DM_GPIO/DM_VIDEO migration for mx53 cx9020 board
- fix boot issue on mx6sabresd board after DM_VIDEO migration
- increase the max preallocated framebuffer BPP to 32 in ipuv3
driver to prepare for configurations with higher color depth
- allow to use vidconsole_put_string() in board code for text
output on LCD displays
The gdsys gazerbeam board is based on a Freescale MPC8308 SOC.
It boots from NOR-Flash, kernel and rootfs are stored on
SD-Card.
On board peripherals include:
- 2x 10/100 Mbit/s Ethernet (optional)
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Migrate the BR/OR settings to Kconfig. These must be known at compile
time, so cannot be configured via DT.
Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The LBLAW_* values determine the window configuration of the memory
controller. Hence, they must be known at compile time, and cannot be
implemented in the DT mechanism.
Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The BATs (block address translation registers) determine the initial
memory window mappings. Hence, they must be known at compile time and
cannot be implemented in the DT mechanism.
Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The HRCW (hardware reset configuration word) is a constant that must be
hard-coded into the boot loader image. So, it must be available at
compile time, and cannot be migrated to the DT mechanism, but has to be
kept in Kconfig.
Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
MPC83xx uses CONFIG_83XX_CLKIN instead of CONFIG_SYS_CLK_FREQ to set the
system clock. To migrate the architecture, we can replace
CONFIG_83XX_CLKIN with CONFIG_SYS_CLK_FREQ.
To do this
* replace all occurrences of CONFIG_83XX_CLKIN with CONFIG_SYS_CLK_FREQ
* set CONFIG_SYS_CLK_FREQ to the old value of CONFIG_83XX_CLKIN in all
MPC83xx config files
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The MPC83xx include files contain some settings of the PCI subsystem.
Migrate these to Kconfig until a proper DM PCI driver exists.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Use the proper CONFIG_TARGET_MPC8349ITX Kconfig option to replace the
CONFIG_MPC8349ITX ad-hoc config option.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The MPC8349EMDS config file contains config options to enable SDRAM
support. To keep this ability after the Kconfig migration, create a new
MPC8349EMDS_SDRAM board that enables the SDRAM support and remove the
SDRAM support from the original board.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
NanoPi M1 plus have a 10/100/1000M ethernet with external phy.
Phy power is controlled by PD6.
Add the required configuration for it.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
SPL_TEXT_BASE was moved into Kconfig, which previously part of
include/configs before this teres_i support gets merged.
Fix it by explicitly define in defconfig like other boards does.
Signed-off-by: Jonas Smedegaard <dr@jones.dk>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
SPL_TEXT_BASE has been moved to Kconfig with commit:
f89d6133ee configs: move CONFIG_SPL_TEXT_BASE to Kconfig
But Beelink GS1 config file has been introduced in the
same time without this modification.
Fix this by settings the CONFIG_SPL_TEXT_BASE
Suggested-by: Jonas Smedegaard <dr@jones.dk>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
vme8349.h contains two separate boards: The vme8349 itself, and the
caddy2 board. The caddy2 board is chosen by setting certain config
variables. Create a proper config file for the caddy2 board to make
Kconfig migration easier.
Furthermore, simplify the vme8349 and caddy2 configs by keeping only the
options necessary for each board.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
MPC8313ERDB has the option of either enabling NOR or NAND boot in its
config file (by commenting out certain #ifdefs). To keep this ability
after migrating options to Kconfig, we introduce two MPC8313ERDB
configs: one for NOR, and one for NAND.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The kmeter1, and kmcoge5ne boards also build from the same config
file with #ifdef logic.
Create a separate include config for each board with the #ifdef logic
resolved as needed.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The kmsupx5, tuge1, kmopti2, and kmtepr2 boards all build from the same
include config file with lots of #ifdef logic.
To ease Kconfig migration, create new config include files for these
boards, and resolve the #ifdef logic as needed.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The kmtegr1, kmvect1, and suvd3 boards all use the same config include
file with lots of #ifdefs in it.
The Kconfig migation will become easier if we get rid of these #ifdefs
first.
Hence, create distinct config include files for these boards, and unwind
the #ifdef logic in these config files to only include the options
necessary for each board.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Meet the following boot hang.
"
U-Boot SPL 2019.04-00661-gdc80a012e4 (Apr 25 2019 - 10:31:57 +0800)
Trying to boot from MMC1
U-Boot 2019.04-00661-gdc80a012e4 (Apr 25 2019 - 10:31:57 +0800)
CPU: Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz)
CPU: Automotive temperature grade (-40C to 125C)Reset cause: POR
Model: Freescale i.MX6 Quad SABRE Smart Device Board
Board: MX6-SabreSD
I2C: ready
DRAM: 1 GiB
Video device 'ipu@2400000' cannot allocate frame buffer memory -ensure the device is set up before relocation
Error binding driver 'ipuv3_video': -28
Video device 'ipu@2800000' cannot allocate frame buffer memory -ensure the device is set up before relocation
Error binding driver 'ipuv3_video': -28
Some drivers failed to bind
Error binding driver 'generic_simple_bus': -28
Some drivers failed to bind
initcall sequence 4ffe4500 failed at call 1780dfb7 (err=-28)
"
1. fdtdec_get_alias_seq will use "video" as base, however in alias node,
we use ipux, so add new alias for U-Boot dts.
2. DM_VIDEO is enabled, however reserve_video is called before
relocation, so to make DM_VIDEO work before relocation, need to
set SYS_MALLOC_F_LEN
3. defconfig is updated with savedefconfig
Note: I do not have a video panel to test, but with this patch, U-Boot
boots up again, below log.
"
U-Boot SPL 2019.04-00662-g0b62453bff (Apr 25 2019 - 10:36:31 +0800)
Trying to boot from MMC1
U-Boot 2019.04-00662-g0b62453bff (Apr 25 2019 - 10:36:31 +0800)
CPU: Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz)
CPU: Automotive temperature grade (-40C to 125C) at 34C
Reset cause: POR
Model: Freescale i.MX6 Quad SABRE Smart Device Board
Board: MX6-SabreSD
I2C: ready
DRAM: 1 GiB
PMIC: PFUZE100 ID=0x10
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 3
Loading Environment from MMC... *** Warning - bad CRC, using default environment
PCI: pcie phy link never came up
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Enable DM_VIDEO in config and don't overwrite console so it can be set
from environment
Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Switch to DM_GPIO and add gpio_request where necessary.
This is needed for DM_VIDEO and fixes an issue with sd card detection
which was introduced by the combination of these commits:
commit 7a0425dd96 ("mmc: fsl_esdhc: make get_cd work well in dm_mmc_ops")
commit 7e04b4c751 ("dm: arm: imx: migrate cx9020 to CONFIG_DM_MMC")
Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
NVMe was turned on in qemu-x86 but somehow we missed it for 64-bit.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Configuration option CONFIG_CMD_BOOTEFI_SELFTEST is useful for the
development of the UEFI sub-system. For production it is not needed.
Remove CONFIG_CMD_BOOTEFI_SELFTEST from bcm968580xref_ram_defconfig.
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Configuration option CONFIG_CMD_BOOTEFI_SELFTEST is useful for the
development of the UEFI sub-system. For production it is not needed.
Remove CONFIG_CMD_BOOTEFI_SELFTEST from bcm963158_ram_defconfig.
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
CONFIG_SYS_[DI]CACHE_OFF had been partially converted to Kconfig
parameters; only for the ARC architecture. This patch turns these two
parameters into Kconfig items everywhere else they are found.
All of the include/configs/* and defconfig changes in this patch are
for arm machines only. The Kconfig changes for arc, nds32, riscv,
and xtensa have been included since these symbols are found in code
under arch/{arc,nds32,riscv,xtensa}, however, no currently-defined
include/configs/* or defconfigs for these architectures exist which
include these symbols.
These results have been confirmed with tools/moveconfig.py.
Acked-by: Alexey Brodkin <abrodkin@snopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Re-migrate for a few more boards]
Signed-off-by: Tom Rini <trini@konsulko.com>
Arndale board has an Asix AX88760 USB 2.0 Hub and Fast Ethernet combo.
The appropriate driver for it is USB_ETHER_ASIX.
The mistake probably came from misinterpretation of commit e9954b867c
("usb: eth: add ASIX AX88179 DRIVER") which was tested on RECS5250 COM
module. This module indeed has Exynos5250 and some similarities with
Arndale 5250 board but the USB/Ethernet chip used there is apparently
different.
Fixes: f58ad98a62 ("usb: net: migrate USB Ethernet adapters to Kconfig")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The CONFIG_DM_I2C_COMPAT was introduced in
include/configs/exynos5-common.h in commit 189d80166b ("exynos5:
enable dm i2c") and then it propagated up to configs/arndale_defconfig.
However since beginning the Arndale board (Exynos5250) was not using
I2C.
In fact, the Arndale board is not configuring its PMIC (S5M8767) which
uses I2C bus. This setting can be thus safely removed to fix build
warning:
This board uses CONFIG_DM_I2C_COMPAT. Please remove
(possibly in a subsequent patch in your series)
before sending patches to the mailing list.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enables the "wdt" command, which is quite useful for watchdog
testing.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Commit d397f7c45b ("net: phy: micrel: Separate KSZ9000 drivers from
KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns
that you shouldn't select both of them due to a device ID clash between
the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a
system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately
boards like the SAMA5D3xEK do contain both types of PHY, but fortunately
the Linux Micrel PHY driver provides a solution by using different PHY
ID and mask values to distinguish these chips.
This commit contains the following changes:
- The PHY ID and mask values for the KSZ9021 and the KS8721 now match
those used by the Linux driver.
- The warnings about not enabling both drivers have been removed.
- The description for PHY_MICREL_KSZ8XXX has been corrected (these are
10/100 PHYs, not GbE PHYs).
- PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE
since this is selected by PHY_MICREL_KSZ90X1.
- All of the relevant defconfig files have been updated now that
PHY_MICREL_KSZ8XXX does not default to 'Y'.
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Re-add support for Aries Embedded MCV SoM, which is CycloneV based
and the associated MCVEVK and MCVEVP baseboard. The board can boot
from eMMC. Ethernet and USB is supported.
The Aries Embedded boards have been removed with commit 03b54997d5
("board/aries: Remove"). I will now take care of them.
The device-tree files are from mainline Linux commit e93c9c99a629
("Linux v5.1)".
Signed-off-by: Wolfgang Grandegger <wg@aries-embedded.de>
CC: Marek Vasut <marex@denx.de>
CC: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Update the default configuration file to enable the necessary functionality
the get the kit working.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Update the default configuration file to enable the necessary functionality
to get the SoCFPGA loadfs driver support. This would enable the
implementation of programming bitstream into FPGA from MMC.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Mark Jonas <mark.jonas@de.bosch.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Improvements and new features:
- split more rockchip pinctrl_core feature into per SoC
- enable TPL for evb-rk3399 board
- enable TPL/SPL for evb-px5 board
- enable TPL and OP-TEE support for evb-rk3229
- update fix in arm common assembly start code for rockchip header file
- update default SPL_FIT_GENERATOR for rockchip
- rk3399 boards update to use '-u-boot.dtsi'
- add new rk3399 boards: Nanopi M4, Nanopc T4
- enable sound for chromebook_minnie
Add initial support for Nanopc T4 board.
Specification
- Rockchip RK3399
- Dual-Channel 4GB LPDDR3-1866
- SD card slot
- 16GB eMMC
- RTL8211E 1Gbps
- AP6356S WiFI/BT
- HDMI In/Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- DC 12V/2A
Commit details of rk3399-nanopc-t4.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: Add NanoPC-T4 IR receiver"
(sha1: 95658e21b1707ad7844f873db2fdaa295109a5a3)
Tested-by: Daniel Gröber <dxld@darkboxed.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When AE350 boots from flash, use CONFIG_OF_SEPARATE instead of
CONFIG_OF_BOARD.
Also remove unused code about prior_stage_fdt_address.
And modify CONFIG_SYS_FDT_BASE as flash address.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
When AE350 boots from ram, use CONFIG_OF_PRIOR_STAGE instead
of CONFIG_OF_BOARD.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Add two defconfigs to support AE350 SMP booting from flash.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
CRS305-1G-4S has a switch chip with an integrated CPU (98DX3236) and
like some of the other similar boards requires bin_hdr.
bin_hdr (DDR3 init stage) is currently retrieved from the stock
bootloader and compiled into the kwb image.
Adds support for U-Boot, enable UART, SPI, Winbond SPI flash chip
support and writing env to SPI flash.
Signed-off-by: Luka Kovacic <me@lukakovacic.xyz>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables CONFIG_BLK and some DM enabled drivers on
db-88f6820-gp to remove these compile warnings:
===================== WARNING ======================
This board does not use CONFIG_DM_MMC. Please update
the board to use CONFIG_DM_MMC before the v2019.04 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does use CONFIG_LIBATA but has CONFIG_AHCI not
enabled. Please update the storage controller driver to use
CONFIG_AHCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
This patch enables CONFIG_BLK to remove this compile warning:
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables CONFIG_BLK and some DM enabled drivers on clearfog
to remove these compile warnings:
===================== WARNING ======================
This board does not use CONFIG_DM_MMC. Please update
the board to use CONFIG_DM_MMC before the v2019.04 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does use CONFIG_LIBATA but has CONFIG_AHCI not
enabled. Please update the storage controller driver to use
CONFIG_AHCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Signed-off-by: Stefan Roese <sr@denx.de>
The Bananapi M3 has an RTL8211E PHY connected to the EMAC using
RGMII. The PHY is powered by DCDC1 through SW @ 3.3V.
The board is designed to use 3.3V with RGMII, instead of the standard
reduced voltage of 2.5V we see everywhere. DLDO3, which provides the
I/O voltages, is raised to match.
This patch enables the EMAC and Realtek PHY drivers in the defconfig.
The device tree file already has the EMAC enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The Cubietruck Plus has an RTL8211E PHY connected to the EMAC using
RGMII. The PHY is powered by DLDO4 @ 3.3V, while the I/O pins are
powered by DLDO3 @ 2.5V.
This patch enables the EMAC and Realtek PHY drivers in the defconfig.
The device tree file already has the EMAC enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Olimex A64-Teres-I board is a mainboard (the only one so far)
for Olimex Teres-I DIY laptop kit.
Key features:
- Allwinner A64 Cortex-A53
- Mali-400MP2 GPU
- AXP803 PMIC
- 2GB DDR3 RAM
- MicroSD Slot
- 16GB eMMC Flash
- eDP LCD display
- HDMI
- USB Host
- Battery management
- 5V DC power supply
- Certified Open Source Hardware (OSHW)
Works:
- i2C
- MMC/SD
- PWM backlight
Known broken:
- Internal keyboard (seems to be because the keyboard firmware loads a
bootloader first, and then disconnects bootloader and connect real
keyboard). External ones connected to the USB port work fine.
This patch enables support for the A64-Teres-I board to u-boot,
including enabling screen backlight (lacking from Linux device-tree).
Linux commit details about the sun50i-a64-teres-i.dts sync:
"arm64: dts: allwinner: a64: Rename uart0_pins_a label to uart0_pb_pins"
(sha1: d91ebb95b96c8840932dc3a10c9f243712555467)
Cosmetic warnings regarding whitespace and placement of SPDX notice for
dts file was ignored.
config and .dtsi file are adapted from pinebook files.
Tested-by: Jonas Smedegaard <dr@jones.dk>
Signed-off-by: Jonas Smedegaard <dr@jones.dk>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: move board entry in MAINTAINERS file at proper position]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Few SPL and U-Boot proper configs are common to all rk3399 target
defconfigs, move them and select it from platform kconfig.
Moved configs:
- SPL_ATF
- SPL_ATF_NO_PLATFORM_PARAM if SPL_ATF
- SPL_LOAD_FIT
- SPL_CLK if SPL
- SPL_PINCTRL if SPL
- SPL_RAM if SPL
- SPL_REGMAP if SPL
- SPL_SYSCON if SPL
- CLK
- FIT
- PINCTRL
- RAM
- REGMAP
- SYSCON
- DM_PMIC
- DM_REGULATOR_FIXED
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add default SPL_FIT_GENERATOR py script for rockchip platforms if
specific target enabled SPL_LOAD_FIT.
So, this would help get rid of explicitly mentioning the default
SPL FIT generator in defconfigs. however some targets, like puma_rk3399
still require their own FIT generator so in those cases the default will
override with defconfig defined generator.
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_SPL_TEXT_BASE was available in configs/rk3399_common.h
when the OrangePI rk3399 board supported during first
version patch.
But, later below change which move this config into Kconfig and
same has been merged in mainline tree.
"configs: move CONFIG_SPL_TEXT_BASE to Kconfig"
(sha1: f89d6133ee)
Unfortunately, the maintainer applied the initial version patch,
instead of looking for next version changes.
Fix it by adding SPL_TEXT_BASE in orangepi-rk3399 defconfig.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable sound for this board, which has the same codec as jerry.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The SPL is now running at SDRAM, and 0x10000 is used by BL31,
and the ARM SPL do not support relocate now, we need reserved
0x50000 so that it won't overwrite the code when we load the
bl31 to target space.
We should remove this after we enable the relocate feature.
The SPL need malloc 0x9000 for MMC as buffer used for transfer
data to IRAM(The EMMC DMA can not transfer data to IRAM directly).
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add a version of samus which supports booting from TPL to SPL and then
to U-Boot. This allows TPL to select from an A or B SPL to support
verified boot with field upgrade.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add board code and DTs for Renesas RZ/A1 SoC-based GR-Peach,
which is a cheap development platform with RZ/A1H SoC. The
DTs are imported from Linux 5.0.11, commit d5a2675b207d .
Currently supported are UART, ethernet and RPC SPI. The board
can be booted from RPC SPI by writing the u-boot.bin binary
to the beginning of the SPI NOR, e.g. using the "sf" command.
The board can also be booted via JTAG by setting text base to
0x20020000, loading u-boot.bin there via JTAG and executing it
from that address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Last change to this board was done in 2016, it uses non-DM USB
with no prospects of ever being converted to DM USB, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Last change to this board was done in 2016, it uses non-DM USB
with no prospects of ever being converted to DM USB, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Convert Stratix 10 SDRAM driver to device model.
Get rid of call to socfpga_per_reset() and use reset
framework.
SPL is changed from calling function in SDRAM driver
directly to just probing UCLASS_RAM.
Move sdram_s10.h from arch to driver/ddr/altera directory.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Enable CMD_SF, MTD, DM_SPI_FLASH, SPI_FLASH, SPI, DM_SPI and
STM32_QSPI flags to be able to use the embedded n25q128a QSPI flash
on stm32f469-disco board.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The DA850 EVM has one USB 1.1 OHCI Host controller. With the
host controller now support DM_USB, this patch enables
the respective functions for the da850evm.
Signed-off-by: Adam Ford <aford173@gmail.com>
The size of the SPL for the am335x_evm is constrained. There is no need
to have advanced SPL FIT features, so keep the SPL FIT support tiny.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Ocelot
- mt7620: rename arch to more generic name mtmips
- mips: pass initrd addresses via DT as physical addresses
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiQkHUH+J02LLC9InKPlOlyTyXBgFAlzMa60ACgkQKPlOlyTy
XBg3FBAAl5I1zNoyEQBuSpe+++0fNFkug0vV985keJA3iXdskdxE8vpxPv6wAp+w
IjBX+e04LY7i5iW58E//f/JBjzL1H345nPeuRsflmlDARep1pqgkEAsEUglGiQW+
ZNDq/aoImWhiiX2nQHnU4ykHNyvIhUOTjldrwU5DfIS2N+8M23pjLhODMsgaNmkd
WfwYB91oTXRnnecwG8Nd1MJU/Jpcns5y6eYwok8vQwkCyzcfsIEP052m3r2SAUMz
3hIlz9WKAHc+pYLz2BWbn560KPJHyS0UqfemiT/M0JasIkojJcQwtrWTKj7g7ZOq
z8XJQ1Ny0xOYQbfbUcvQttBwVXzYQTKy0jS6qi4vB9Q0TgpRP+v//n29IAJA0YkS
BE3Nq96cCMgKarSFkMFaXifv9flnb/wZRymB42Frb9fqiwM2wX10zhcn7zW8gUYc
0Mocl+zkUrmtmA3gSspMJr6kkfX629l97RK7wiY0PkTa4OKSqqMR5JxlVQ+vK72N
f/yxWYxTH/90wfVolTHt52J/hNydEapVFuudL8ffnuLo84BWzOHP3bwQwtB927zV
g4nHxotTmVErz5Pr2JrwaZEFVI+Sc+wXPz68Z7hzZxeiO5tBAELhvtDKAsf9e1gt
OFgQwA5cTRWWxLmWxyWY3nEbXVqAIOsdWIDepAUqrIXAI5rmFt8=
=SZ/W
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-05-03' of git://git.denx.de/u-boot-mips
- mscc: small fixes, enhance network support for Serval, Luton and Ocelot
- mt7620: rename arch to more generic name mtmips
- mips: pass initrd addresses via DT as physical addresses
This converts the following to Kconfig:
CONFIG_SUPPORT_EMMC_BOOT
As requested by Michal Simek <michal.simek@xilinx.com>, these boards
have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated:
xilinx_zynqmp_zc1275_revB
xilinx_zynqmp_zc1751_xm018_dc4
xilinx_zynqmp_zc1751_xm019_dc5
xilinx_zynqmp_zcu100_revC
xilinx_zynqmp_zcu102_rev1_0
xilinx_zynqmp_zcu102_revA
xilinx_zynqmp_zcu102_revB
xilinx_zynqmp_zcu104_revA
xilinx_zynqmp_zcu104_revC
xilinx_zynqmp_zcu106_revA
xilinx_zynqmp_zcu111_revA
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Currently mach-mt7620 contains only support for mt7628. To avoid confusion,
rename mach-mt7620 to mach-mtmips, which means MediaTek MIPS platforms.
MT7620 and MT7628 should be distinguished by SOC_MT7620 and SOC_MT7628
because they do not share the same lowlevel codes.
Dependencies of four drivers are changed to SOC_MT7628 as these drivers
are only used by MT7628.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Add am335x-pocketbeagle to CONFIG_OF_LIST in am335x_evm_defconfig.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
- at91sam9g20-taurus.dts: use labels
- cleanup taurus port to compile clean with
current mainline again. SPL has no serial
output anymore, so it fits into SRAM.
Signed-off-by: Heiko Schocher <hs@denx.de>
This options will be enabled by default by CZ.NIC shipped U-Boot. Enable
them in defconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for the gpio command and driver for the I2C connected
pca9538 controller, to be able to determine if SFP module is present in
the Turris Omnia router.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This driver is required for Turris Omnia to read ethernet addresses.
Move the dependency from turris_omnia_defconfig to Kconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable AHCI, SCSI and SATA for compliance with the driver model
migration.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add XHCI_HOST and XHCI_MVEBU to defconfig, so that user's can by default
boot from USB on Turris Omnia.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
-----BEGIN PGP SIGNATURE-----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=CzWQ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20190426' of git://git.denx.de/u-boot-imx
Porting to DM and i.MX8
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
Use board_debug_uart_init() for UART iomux init instead of
do it in board_init_f, and move the function to soc file so
that we can find all the soc/board setting in soc file and
use a common board file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Fixed whitespace error:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable debug uart for kylin board in defconfig.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Over the last quarter, a part of our production has used NOR flash
from Gigadevice in addition to the Winbond parts that we typically
source. This requires the SPI_FLASH_GIGADEVICE config to be set.
Enable SPI_FLASH_GIGADEVICE in the board's default defconfig.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
The da850evm include environment/ti/mmc.h and places
DEFAULT_MMC_TI_ARGS, defined int that file, in
CONFIG_EXTRA_ENV_SETTINGS. This has been broken for some time
since neither CMD_PART nor CMD_UUID are available, so manually
changing the environmental variables was always required before
booting from MMC. With this patch, these scripts should work
again, and by default they point to mmc 0, partition 2, and
the dtb file exists in a /boot directory on partition 2.
Signed-off-by: Adam Ford <aford173@gmail.com>
A previous patch converted a bunch of settings for CONFIG_SF_DEFAULT
but it broke the SPI Flash which now prevents booting. This patch
now correctly sets CONFIG_SF_DEFAULT_SPEED=30000000 to match what it
was before the conversion.
Fixes: 14453fbfad ("Convert CONFIG_SF_DEFAULT_* to Kconfig")
Signed-off-by: Adam Ford <aford173@gmail.com>
Add new defconfig files for the AM65x High Security EVM.
This defconfigs are the same as for the non-secure part, except for:
CONFIG_TI_SECURE_DEVICE option set to 'y'
CONFIG_FIT_IMAGE_POST_PROCESS option set to 'y'
CONFIG_SPL_FIT_IMAGE_POST_PROCESS option set to 'y'
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
- Add DM based generic watchdog start and reset implementation
and remove all ad-hoc implementations (Stefan)
- Move mv_sdhci to DM (Pierre)
- Misc turris_omnia updates (Pierre)
- Change openrd targets to correctly build again (size changes
and fixes to the dts targets) and bring it back into Travis
builds (Stefan)
- Add Kirkwood db-88f6281-bp board (Chris)
With the new generic function, the scattered other functions are now
removed to be replaced by the generic one. The new version also enables
the configuration of the watchdog timeout via the DT "timeout-sec"
property (if enabled via CONFIG_OF_CONTROL).
The watchdog servicing is enabled via CONFIG_WATCHDOG.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
With the latest changes to the drivers (SPI_FLASH_SPANSION etc), Travis
reports that the SPL image is too big. Let's use the thumb instructions
in SPL to save some space and make the image fit again.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Switch to the driver model for USB on the db-88f6281-bp board.
CONFIG_BLK can't be enabled yet because mvebu_mmc.c needs converting.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This is Marvell's Kirkwood development board. It has the following
features
- 512M DDR2
- 2 PCI connectors
- 1 x1 PCI-e interface
- 1 Gigabit Ethernet Port
- 2 SATA Ports
- USB 2.0 Interface
- SDIO
- 128M NAND Flash
- 16M SPI Flash
It can be strapped to boot from SPI or NAND so there are two defconfigs
(one per boot media).
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable DM_MMC for compliance with the driver model migration.
Signed-off-by: Pierre Bourdon <delroth@gmail.com>
Cc: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
1. Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.
2. Fix legacy USB command (both sdboot and usbboot can be used now).
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This commit switches to DM USB for warp7 and warp7_bl33 defconfigs.
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This commit switches to DM SERIAL for warp7 and warp7_bl33 defconfigs.
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This patch enable convert DM MMC for imx7d-pico board and variant.
Before the DM conversion only usdhc3 was enabled and therefore it appeared
as MMC 0 to u-boot. After enabling MMC DM though usdhc3 defaults to MMC 2,
which left unattended would drive changes to existing pico-pi bootscripts and
environment variables that rely on mmc 0.
Setup the alias of mmc0 and usdhc3 so that existing pico-imx7d boot code will
work unmodified.
When converting to DM_MMC it is necessary that SPL initializes eMMC
by itself, so move the original eMMC initialization from U-Boot
proper to SPL.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
This patch is necessary for convert this board to dm driver model
DM GPIO requires gpio_request() to be called explicitly before
doing any gpio operation
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Migrate Ethernet FEC to using driver model.
Drop PHY_MICREL_KSZ90X1 which slipped in from Apalis iMX6.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate USB to using driver model.
Add USBH_PEN GPIO regulator.
While at it also add alias e.g. as required for UMS.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate MMC to using driver model.
Migrate USDHC to using pinctrl.
While at it also add GPIO1_IO03__OSC32K_32K_OUT pin muxing.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate pinctrl and regulators to device tree resp. driver model:
Ethernet, NAND and UART.
Drop BOARD_EARLY_INIT_F as it is anyway no longer used.
Enable CMD_DM, CMD_MTD, CMD_REGULATOR and DM_REGULATOR_FIXED.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Drop disabling SPL_SYS_THUMB_BUILD as we anyway do not use SPL.
Enbale CRC32 verify, USB SDP and EFI loader support.
Drop CMD_GPT and disabling RANDOM_UUID.
Do savedefconfig which drops USB_FUNCTION_SDP.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
with u-boot,dm-spl added for imx8qx-pm node, and SPL_SIMPLE_BUS enabled,
the bind and probe code in board file could be removed.
Also we need to enlarge SYS_MALLOC_F_LEN to avoid calloc fail.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Some variations of the imx6q_logic board have eMMC instead of
NAND. Rather than creating a separate defconfig, this patch
adds the ability to read/write to eMMC (mmc 0:1) when NAND
doesn't exist.
Signed-off-by: Adam Ford <aford173@gmail.com>
All socfpga boards except for vining_fpga use DM_I2C. Enable
DM_I2C for this board and set the EEPROM defines via Kconfig
(enabling CONFIG_I2C_EEPROM from MISC).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Series-changes: 2
- added (this) patch to move socfpga_vining to DM_I2C
This commit moves common config options used in all socfpga boards
to select/imply in Kconfig. This both cleans up the defconfig files
as well as makes future changes easier.
Options implied/defaulted for all sub-arches:
- SPL, SPL_DM, USE_TINY_PRINTF, NR_DRAM_BANKS
Options implied/defaulted for implied for A10 & gen5:
- FPGA_SOCFPGA, SYS_MALLOC_F_LEN, SYS_TEXT_BASE
Options implied/defaulted for gen5:
- SPL_STACK_R, SPL_SYS_MALLOC_SIMPLE, SPL_STACK_R_ADDR
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
This enables DM_RTC and RTC_M41T62 to enable support for the rtc on the
socrates board.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Fixes for tracing with sandbox
Refactoring for boot_get_fdt()
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlzAfvkACgkQfxc6PpAI
reYu9AgAjaFmydXjE8DxkSB3rR7DHZFTs1erVKAAL2v+Tdf7LDmz+j6u1M3v55WY
6r54f/gZ1UX5TEmQgEAKLa7QvvRO/lNvSGQnLHhZhv2IVWo7uWCKAUPdQ6XVZnUK
zO5v+ucs9Ne4HxQJHMC509HUIIBbydiRvUm8W0SeBZy4kEyJDuub4L+rpARkXNks
IZfKuY+VS4FK73D4M9PIhoXSubZgVS4AEcapakU1DvEz0kjsN4wr4idGrp3lutPC
455imz83JBq2+mx1oxclOGedkIDzTCq+nWQAwSftMehrJpGrp7RLNo0v4QZZUf4V
LIXRqObIYse9yQLkYPpeBdePMc8/tQ==
=0NJ2
-----END PGP SIGNATURE-----
Merge tag 'pull-24apr19' of git://git.denx.de/u-boot-dm
Various minor sandbox iumprovements
Fixes for tracing with sandbox
Refactoring for boot_get_fdt()
This patch series reworks the implementation of the `bootefi` command to
remove code duplication by using the LoadImage() boot service to load
binaries.
Missing short texts for UEFI protocols are added for display by the
`efidebug dh` command.
Missing parameter checks for AllocatePages() and CreateDeviceNode() are
implemented.
The constants for protocol GUIDs are changed to match the names in the UEFI
specification.
-----BEGIN PGP SIGNATURE-----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=caQ+
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-07-rc1-3' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc1 (3)
This patch series reworks the implementation of the `bootefi` command to
remove code duplication by using the LoadImage() boot service to load
binaries.
Missing short texts for UEFI protocols are added for display by the
`efidebug dh` command.
Missing parameter checks for AllocatePages() and CreateDeviceNode() are
implemented.
The constants for protocol GUIDs are changed to match the names in the UEFI
specification.
These two buffers currently conflict if tracing is enabled. Move the
pre-console buffer and update the documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
The 'phy' reset of gmac device in kernel device tree is not generic
enough for u-boot to use, so we need to overwrite the 'resets' property
as needed. With this device tree fixup and poplar_defconfig changes,
Ethernet starts working on Poplar board.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This config file is shared between stm32f746-disco and stm32f769-disco.
These 2 boards doesn't embed the same qspi flash (Micron n25q128a on
f746-disco, Macronix mx66l51235l on f769-disco).
To be able to use Macronix mx66l51235l on F769-disco, flags
SPI_FLASH_MACRONIX must be enabled.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
When using the generic PHY on boards using an RGMII Realtek PHY,
gigabit speed is not always reliable.
This patch enables the Realtek PHY driver for such boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Amlogic U200 board is based on the Amlogic S905D2 SoC
from the Amlogic G12A SoC family.
The board has the following specifications :
- Amlogic S905D2 ARM Cortex-A53 quad-core SoC
- XGB DDR4 SDRAM
- 10/100 Ethernet (Internal PHY)
- 1 x USB 3.0 Host
- eMMC
- SDcard
- Infrared receiver
- SDIO WiFi Module
- MIPI DSI Connector
- Audio HAT Connector
- PCI-E M.2 Connector
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
vexpress_ca15_tc2_defconfig and vexpress_ca9x4_defconfig do not provide
device trees (as $fdtcontroladdr) as needed to pass our Travis CI tests.
As we are on the move to requiring block devices to be based on the driver
model these boards either will have to be converted to use device trees or
will be kicked out of U-Boot.
So let's disable CONFIG_EFI_LOADER on these boards until the device tree
issue is resolved.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Enable the nand support (driver and command)
in the configuration of the board bcm963158.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Enable the nand support (driver and command)
in the configuration of the board bcm968580xref.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Enable the nand support (driver and command)
in the configuration of the board bcm96838gerg.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcvW07AAoJEB6zHgIOrC/Iu4QH/1REDOTrsZPydd2yD/O81vPs
RiLC8wP2J4UmqtMcNTLyvxlYwrzqoR5J6SYdyBNU/+cLEp/gdzEI+rjsfSV2uRX1
Qb4Pk2FiI503JVjegxsbJqzASfiEP7rIg3HM5431xbhYH22MW2FH6le6yrtNxjBh
m1WFjQYX1bpbGb6zue8TgyLIeN1IqWuqnH9kUHixUEan+xrpEhN239LDFjdvGbvC
BvYyMtDddmMt4YDzNjgX36us993kylGZp6JijR3zgUao7I/JGVZAJrxw8MHDTnVy
UKv3VI9F5bGLSvzqTVL2MFU6XtJW26v+niGLhGzlUhb3TTKrdKOicm3VF7tO+JU=
=MamK
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2019.07-b' of git://git.denx.de/u-boot-atmel
Second set of u-boot-atmel features and fixes for 2019.07 cycle
Use the DWC2 device driver with DM_USB_GADGET support and
cleanup the USB support in STM32MP1 board.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Remove the HOST support for STM32MP1 USBO device = OTG DWC2.
The current DWC2 driver have no dynamic detection of device,
So it is dangerous to have start 3V3 when PC is
connected to the micro USB connector.
=> it is preferable to have only DEVICE support
CONFIG_USB_GADGET_DWC2_OTG for OTG port
See DWC3 driver for clean dual role support...
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
USB_MUSB_TI requires USB_MUSB_DSPS, failing at link time if it's not
selected:
drivers/usb/musb-new/built-in.o: In function `ti_musb_host_ofdata_to_platdata':
drivers/usb/musb-new/ti-musb.c:193: undefined reference to `musb_dsps_ops'
or if OF_CONTROL is not selected:
arch/arm/mach-omap2/built-in.o:(.data.usb0+0x24): undefined reference to `musb_dsps_ops'
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- 16GB eMMC
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- USB 2.0 and 3.0 Host
- HDMI port
- S/PDIF port
- 5V/2A DC power supply
- Wi-Fi/BT via Fn-Link 6222B-SRB (RTL8222BS)
Linux commit details about the sun50i-h6-beelink-gs1.dts sync:
"arm64: dts: allwinner: h6: Introduce Beelink GS1 board"
(sha1: 089bee8dd119ba084dee6b17a2e1a53df4f30193)
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The SAMA5D2 ICP Board features the SAMA5D27 SoC,
together with QSPI Flash, Wilc3000 wireless device and
EtherCat support.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Stratix10 maps dram in 2 address spans, from 0-2GB and from
2GB up to 128GB.
Signed-off-by: Dalon Westergreen <dalon.westergreen@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
fpga:
- Add support for external data in FIT
- Extend testing for external data case
- Inform user about a need to run post config on Zynq
arm:
- Tune zynq command functions
- Fix internal variable setting
arm64:
- Add support for zc39dr decoding
- Disable WDT for zcu100
- Small changes in reset_reason()
- Some DT changes (spi)
- Tune qspi-mini configuration
- Remove useless eeprom setting
- Fix two sdhci boot case
spi:
- Fix tap delay programming
clk:
- Enable i2c in SPL
net:
- Fix gem phydev handling
- Remove phy detection code from gem driver
general:
- Correct EXT_DTB usage for MULTI_DTB_FIT configuration
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAly262oACgkQykllyylKDCH44gCbBnuxUH6ZF0B7Leuee4te7C59
LmUAn14/bbtMt17zkMSADCjY9yGWF4au
=mWrW
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2019.07' of git://git.denx.de/u-boot-microblaze
Xilinx/FPGA changes for v2019.07
fpga:
- Add support for external data in FIT
- Extend testing for external data case
- Inform user about a need to run post config on Zynq
arm:
- Tune zynq command functions
- Fix internal variable setting
arm64:
- Add support for zc39dr decoding
- Disable WDT for zcu100
- Small changes in reset_reason()
- Some DT changes (spi)
- Tune qspi-mini configuration
- Remove useless eeprom setting
- Fix two sdhci boot case
spi:
- Fix tap delay programming
clk:
- Enable i2c in SPL
net:
- Fix gem phydev handling
- Remove phy detection code from gem driver
general:
- Correct EXT_DTB usage for MULTI_DTB_FIT configuration
Remove unneeded configs from mini qspi configuration
so that it saves space for this mini configuration.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not enable WDT by default on this target because distributions are
not enabling watchdog driver to service it.
Feature has been enabled by:
"arm64: zynqmp: Enable cadence WDT for zcu100"
(sha1: 767afebbcd)
And WDT is still enabled in rebranded Avnet Ultra 96 board support.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
-----------
- DM support in sata
- Toradex Board to DM
- wandboard to DM
- tbs2910 to DM
- GE boards to DM
- VHybrid boards to DM
- DM_VIDEO for i.MX
-----BEGIN PGP SIGNATURE-----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=KLsH
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20190415' of git://git.denx.de/u-boot-imx
Move to DM
-----------
- DM support in sata
- Toradex Board to DM
- wandboard to DM
- tbs2910 to DM
- GE boards to DM
- VHybrid boards to DM
- DM_VIDEO for i.MX
Enable CONFIG_AHCI to fix errors:
drivers/ata/dwc_ahsata.c: In function `ahci_init_one':
drivers/ata/dwc_ahsata.c:868:21: error: `struct blk_desc' has no member named `priv'
sata_dev_desc[pdev].priv = uc_priv;
^
drivers/ata/dwc_ahsata.c: In function `init_sata':
drivers/ata/dwc_ahsata.c:891:30: error: `struct blk_desc' has no member named `priv'
uc_priv = sata_dev_desc[dev].priv;
...
Also enable DM_SCSI to fix migration build warning.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Use device tree to set MTD partitions of the NAND chip.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate FEC, ESDHC, NFC and USB to driver model.
While at it also do no longer enable optional I2C clock in board file as
the generic clock code now handles this. Note for space reason and as
it is not required just for booting we do not enable I2C in U-Boot by
default.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate pinctrl and regulators to device tree resp. driver model: DDR,
DSPI, ENET, ESDHC, I2C, NFC and UART.
Enable CMD_DM, PINCTRL and DM_REGULATOR.
While at it also update copyright period and sort include files.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Disable more obscure options to save another 26 KB in preparation of
the upcoming driver model migration.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
While commit 3e020f03e9 ("driver: misc: add MXC_OCOTP Kconfig entry")
introduced a Kconfig entry it did not actually migrate all
configurations to using it.
As CONFIG_MXC_OCOTP was in mx{6/7}_common.h enable it by default on
those architectures. Additionally, also enable it on ARCH_IMX8M and
ARCH_VF610 where all current members enabled it through their legacy
configuration header files.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Limit the size of the malloc() pool before relocation
(SYS_MALLOC_F_LEN).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>