When armada-385.dtsi was sync'd from Linux the name of the node
describing the pcie controller was changed from pcie-controller to pcie.
Some of the boards that include armada-385.dtsi were missed in the
update retaining the old name. This updates the affected boards.
Reported-by: Влад Мао <vlaomao@gmail.com>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The conversion to DM_SPI managed to break accessing the environment on
dreamplug. This is because the environment code relies on being to able
to select the SPI device based on the sequence number. Add an alias so
that the spi0 bus gets sequence number 0.
Reported-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Stefan Roese <sr@denx.de>
Syscon register is required in dts to select correct
PHY interface.
Fix error below:
Net: Failed to get syscon: -2
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Barrier transactions from CCI400 need to be disabled till
the DDR is configured, otherwise it may lead to system hang.
The patch adds workaround to fix the erratum.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
spba-bus has a few nodes under it including the UART1 and
some ESPI buses. In order to use them in SPL, the
u-boot,dm-spl flag needs to be added to the spba-bus@2000000
container.
Signed-off-by: Adam Ford <aford173@gmail.com>
Currently the CPU frequency is incorrectly reported:
CPU: NXP i.MX8QXP RevB A35 at 147228 MHz
Fix this problem by using a direct call to the SCU firmware to
retrieve the Cortex A35 CPU frequency.
With this change applied the CPU frequency is displayed correctly:
CPU: NXP i.MX8QXP RevB A35 at 1200 MHz
Tested-by: Marcelo Macedo <marcelo.macedo@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
Select CONFIG_DM_MMC=y in order to support MMC driver model.
This allows the MMC board related code to be removed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Import the device tree files from kernel 5.0-rc6 in preparation
for driver model conversion.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
This is currently missing and without it the i8254 beeper driver
won't work.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The pc speaker driven by the i8254 is generic enough to deserve
a single dtsi file to be included by boards that use it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The i8254 timer control IO port (0x43) should be setup correctly
by using PIT counter 2 to generate beeps, however in U-Boot other
codes like TSC driver utilizes PIT for TSC frequency calibration
and configures the counter 2 to a different mode that does not
beep. Fix this by always ensuring the PIT counter 2 is correctly
initialized so that the i8254 beeper driver works as expected.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Just add spaces around '=' sign for clarity.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add startup time to LDO regulators of S2MPS11 PMIC on Odroid XU3/XU4/HC1
family of boards to be sure the voltage is proper before relying on the
regulator.
The datasheet for all the S2MPS1x family is inconsistent here and does
not specify unambiguously the value of ramp delay for LDO. It mentions
30 mV/us in one timing diagram but then omits it completely in LDO
regulator characteristics table (it is specified for bucks).
However the vendor kernels for Galaxy S5 and Odroid XU3 use values of 12
mV/us or 24 mV/us.
Without the ramp delay value the consumers do not wait for voltage
settle after changing it. Although the proper value of ramp delay for
LDOs is unknown, it seems safer to use at least some value from
reference kernel than to leave it unset.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The ADC block requires VDD supply to be on so provide one.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Intel Edison has three UART ports, i.e.
port 0 - Bluetooth
port 1 - auxiliary, available for general purpose use
port 2 - debugging, usually console output is here
Enable all of them for future use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The console is actually serial #2. When we would like to enable other ports,
this would be not okay to mess up with the ordering.
Thus, fix the number of default console interface to be 2.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We may not do an assumption that current console device is always a first
of UCLASS_SERIAL one.
For example, on properly described Intel Edison board the console UART
is a third one.
Use current serial device as described in global data.
Fixes: a61cbad78e ("dm: serial: Adjust serial_getinfo() to use proper API")
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Intel Tangier SoC has a general purpose DMA which can serve to speed up
communications on SPI and I2C serial buses.
Provide DMA descriptors to utilize this capability in the future.
Note, I2C6, which is available to user, has no DMA request lines connected.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Intel Tangier SoC has a general purpose DMA which can serve to speed up
communications on SPI and I2C serial buses.
Provide DMA descriptors to utilize this capability in the future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The bootrom seems to leave the D-cache in messed up state, make sure
the SPL disables it so it can not interfere with operation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
The values for the data and tag latency settings on the PL310 caches
controller is an (n-1). For example, the "arm,tag-latency" is specified
as <1 1 1>, so the values that should be written to register should be
0x000. And for the "arm,data-latency" specified as <2 1 1>, the register
value should be 0x010.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
v2019.01 commit cbff9f80ce ("ARM: dts: rmobile: Sync Gen3 DTs with
Linux 4.19.6") made the sdhi/usb nodes available in r8a77965.dtsi.
Hence, remove the SDHI/USB nodes from r8a77965-u-boot.dtsi. This is
equivalent to partially reverting below v2019.01 commits:
- f529bc551b ("ARM: dts: rmobile: Extract USB nodes on M3N")
- 830b94f768 ("ARM: dts: rmobile: Extract SDHI nodes on M3N")
Duplicating the nodes from <soc>.dtsi to <soc>-u-boot.dtsi is obviously:
- not needed if no U-boot-specific changes are needed in those nodes.
- potentially dangerous/error-prone, since the duplicated properties
override the properties originally defined in <soc>.dtsi. One
possible consequence is that <soc>.dtsi is getting an update from
Linux, while <soc>-u-boot.dtsi stays unchanged. In this situation,
the obsolete property values from <soc>-u-boot.dtsi will take
precedence masking some of the <soc>.dtsi updates, potentially
leading to all kind of obscure issues.
Below is the dtdiff of r8a77965-salvator-x-u-boot.dtb (the only "user"
of r8a77965-u-boot.dtsi) before and after the patch (slightly
reformatted to avoid 'git am/apply' issues and to reduce the width).
What below output means is there is already a mismatch in some of
SDHI/USB nodes between r8a77965.dtsi and r8a77965-u-boot.dtsi. Since no
U-Boot customization is needed in SDHI/USB DT nodes, get rid of them in
r8a77965-u-boot.dtsi.
$> dtdiff before-r8a77965-salvator-x-u-boot.dtb \
after-r8a77965-salvator-x-u-boot.dtb
--- /dev/fd/63 2019-03-09 12:57:40.877963983 +0100
+++ /dev/fd/62 2019-03-09 12:57:40.877963983 +0100
@@ -1471,7 +1471,7 @@
bus-width = <0x4>;
cd-gpios = <0x51 0xc 0x1>;
clocks = <0x6 0x1 0x13a>;
- compatible = "renesas,sdhi-r8a77965";
+ compatible = "renesas,sdhi-r8a77965", "renesas,rcar-gen3-sdhi";
interrupts = <0x0 0xa5 0x4>;
max-frequency = <0xc65d400>;
pinctrl-0 = <0x4d>;
@@ -1492,7 +1492,7 @@
sd@ee120000 {
clocks = <0x6 0x1 0x139>;
- compatible = "renesas,sdhi-r8a77965";
+ compatible = "renesas,sdhi-r8a77965", "renesas,rcar-gen3-sdhi";
interrupts = <0x0 0xa6 0x4>;
max-frequency = <0xbebc200>;
power-domains = <0x1 0x20>;
@@ -1504,7 +1504,7 @@
sd@ee140000 {
bus-width = <0x8>;
clocks = <0x6 0x1 0x138>;
- compatible = "renesas,sdhi-r8a77965";
+ compatible = "renesas,sdhi-r8a77965", "renesas,rcar-gen3-sdhi";
fixed-emmc-driver-type = <0x1>;
interrupts = <0x0 0xa7 0x4>;
max-frequency = <0xbebc200>;
@@ -1526,7 +1526,7 @@
bus-width = <0x4>;
cd-gpios = <0x5a 0xf 0x1>;
clocks = <0x6 0x1 0x137>;
- compatible = "renesas,sdhi-r8a77965";
+ compatible = "renesas,sdhi-r8a77965", "renesas,rcar-gen3-sdhi";
interrupts = <0x0 0xa8 0x4>;
max-frequency = <0xc65d400>;
pinctrl-0 = <0x56>;
@@ -1868,14 +1868,14 @@
usb-phy@ee0a0200 {
#phy-cells = <0x0>;
- clocks = <0x6 0x1 0x2be>;
+ clocks = <0x6 0x1 0x2bf>;
compatible = "renesas,usb2-phy-r8a77965", "renesas,rcar-gen3-usb2-phy";
phandle = <0x47>;
pinctrl-0 = <0x4c>;
pinctrl-names = "default";
power-domains = <0x1 0x20>;
reg = <0x0 0xee0a0200 0x0 0x700>;
- resets = <0x6 0x2be>;
+ resets = <0x6 0x2bf>;
status = "okay";
};
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
U-Boot currently uses Gen2 QSPI in 1-bit mode, enforce it until
we can do better using the new SPI NOR framework.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
- Enable DHCP as boot-source in distro boot for NXP layerscape
platforms
- fix register layout for SEC on Layerscape architectures
- fixes related to DPAA2 ethernet
sec_firmware reserves JR3 for it's own usage and deletes the JR3 node
from the device tree. This causes this warning to be issued when doing
the device tree fixup:
WARNING could not find node fsl,sec-v4.0-job-ring: FDT_ERR_NOTFOUND.
Fix it by excluding the device tree fixup for the JR reserved by
sec_firmware.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The SEC QI ICID setup in the QIIC_LS register is actually an offset
that is being added to the ICID coming from the qman portal. Setting
it with a non-zero value breaks SMMU setup as the resulting ICID is
not known. On top of that, the SEC QI ICID must match the qman portal
ICIDs in order to share the isolation context.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Moving to the driver model requires CONFIG_DM to be enabled. Currently
several boards like kmeter1_defconfig produce a build error when CONFIG_DM
is enabled:
In file included from include/common.h:35,
from ./arch/powerpc/include/asm/fsl_lbc.h:10,
from include/mpc83xx.h:10,
from ./arch/powerpc/include/asm/ppc.h:27,
from ./arch/powerpc/include/asm/u-boot.h:18,
from include/dm/of.h:10,
from include/dm/ofnode.h:12,
from include/dm/device.h:13,
from include/linux/mtd/mtd.h:26,
from drivers/mtd/mtdconcat.c:25:
include/image.h: In function ‘image_check_target_arch’:
include/image.h:846:3: error: #error "please define IH_ARCH_DEFAULT in
your arch asm/u-boot.h"
# error "please define IH_ARCH_DEFAULT in your arch asm/u-boot.h"
^~~~~
include/image.h:848:31: error: ‘IH_ARCH_DEFAULT’ undeclared (first use in
this function); did you mean ‘IH_ARCH_COUNT’?
return image_check_arch(hdr, IH_ARCH_DEFAULT);
The error can be avoided by moving the definition of IH_ARCH_DEFAULT before
#include <asm/ppc.h>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The loop implemented in the code is supposed to check whether the
PL310 operation register has any bit from the mask set. Currently,
the code checks whether the PL310 operation register has any bit
set AND whether the mask is non-zero, which is incorrect. Fix the
conditional.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Tom Rini <trini@konsulko.com>
Fixes: 93bc21930a ("armv7: add PL310 support to u-boot")
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
This patch enables CONFIG_SYS_BOOT_RAMDISK_HIGH for RISC-V
because bootm will update initrd location in DTB only if
CONFIG_SYS_BOOT_RAMDISK_HIGH is enabled. If we don't enable
this option then bootm assumes DTB already has initrd details
which is not the case most of the time.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
This patch adds SiFive FU540 board support. For now, only
SiFive serial, SiFive PRCI, and Cadance MACB drivers are
only enabled. The SiFive FU540 defconfig by default builds
U-Boot for S-Mode because U-Boot on SiFive FU540 will run
in S-Mode as payload of BBL or OpenSBI.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds fixed-factor clock driver which derives clock
rate by dividing (div) and multiplying (mult) fixed factors
to a parent clock.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On 64bit systems, the DRAM top can be easily beyond 4GB and U-Boot
DMA mapping APIs will generate DMA addresses beyond 4GB. This
breaks DMA programming in 32bit DMA capable devices (such as
Cadence MACB ethernet). For example, If DRAM is more then 2GB
on QEMU sifive_u machine then Cadence MACB ethernet stops working
for U-Boot because it is a 32bit DMA capable device.
To handle 32bit DMA capable devices on 64bit systems, we provide
custom implementation of board_get_usable_ram_top() which ensures
that usable ram top is not more then 4GB. This in-turn ensures
that U-Boot always runs within 4GB hence DMA addresses generated
by DMA mapping APIs will be within 4GB too.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some of the drivers (such as Cadence MACB ethernet driver) expect
asm/arch/clk.h to be provided by arch support so we add place-holder
asm/arch-generic/clk.h for RISC-V generic CPU.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
This patch adds asm/dma-mapping.h for Linux-like DMA mappings
APIs required by some of the drivers (such as, Cadance MACB
Ethernet driver).
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
The QEMU CPU support under arch/riscv is pretty much generic
and works fine for SiFive Unleashed as well. In fact, there
will be quite a few RISC-V SOCs for which QEMU CPU support
will work fine.
This patch renames cpu/qemu to cpu/generic to indicate the
above fact. If there are SOC specific errata workarounds
required in cpu/generic then those can be done at runtime
in cpu/generic based on CPU vendor specific DT compatible
string.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We select CREATE_ARCH_SYMLINK for RISC-V so that we can have
include/asm/arch linked to include/asm/arch-xyz.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Imply all SoCs supported by a given board. This allows building single
U-Boot binary for boards which can have multiple SoCs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Imply preferred pin control driver per SoC, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
On SoCFPGA Gen5 systems, it can rarely happen that a reboot from Linux
will result in stale data in PL310 L2 cache controller. Even if the L2
cache controller is disabled via the CTRL register CTRL_EN bit, those
data can interfere with operation of devices using DMA, like e.g. the
DWMMC controller. This can in turn cause e.g. SPL to fail reading data
from SD/MMC.
The obvious solution here would be to fully reset the L2 cache controller
via the reset manager MPUMODRST L2 bit, however this causes bus hang even
if executed entirely from L1 I-cache to avoid generating any bus traffic
through the L2 cache controller.
This patch thus configures and enables the L2 cache controller very early
in the SPL boot process, clears the L2 cache and disables the L2 cache
controller again.
The reason for doing it in SPL is because we need to avoid accessing any
of the potentially stale data in the L2 cache, and we are certain any of
the stale data will be below the OCRAM address range. To further reduce
bus traffic during the L2 cache invalidation, we enable L1 I-cache and
run the invalidation code entirely out of the L1 I-cache.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Configure the PL310 tag and data latency registers, which slightly
improves performance and aligns the behavior with Linux.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
The loop implemented in the code is supposed to check whether the
PL310 operation register has any bit from the mask set. Currently,
the code checks whether the PL310 operation register has any bit
set AND whether the mask is non-zero, which is incorrect. Fix the
conditional.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Tom Rini <trini@konsulko.com>
Fixes: 93bc21930a ("armv7: add PL310 support to u-boot")
- Add support for sound.
Albeit the big changeset, changes are pretty limited to x86 only and a
few new sound drivers used by x86 so I think it would be good to have
this in the next release.
This patch enables UMS on the nyan devices like the nyan-big.
A patch like this has been sent in by Stephen Warren some time ago for
other tegra devices: commit e6607cffef.
But the nyan devices never received that functionality.
Signed-off-by: Tristan Bastian <tristan-c.bastian@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Internal keyboard of nyan-big is only working when cold booting by pressing [reload/refresh]+[power] button.
With this patch keyboard is working by only pressing [power] button.
Signed-off-by: Tristan Bastian <tristan-c.bastian@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable sound on samus using the broadwell I2S and an RT5677 audio codec.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for initing the I2C device and ADSP on broadwell. These are
needed for sound to work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the pinctrl probes the PCH but since it only uses it to obtain
a PCI address, this is no necessary. Avoiding this fixes one of the two
co-dependent loops in broadwell.
This driver really should be a proper pinctrl driver, but for now it
remains a syscon device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Application Digital Signal Processor is used for sound processing with
broadwell. Add a driver to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Adjust the code to allow beeping at different frequencies, using a
calculated value for timer 2.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add sound support for link, using the HDA codec implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When testing the sound system we don't need the hear the beeps. The
testing works by checking the data that would be emitted. Add a
device-tree property to silence the sound, and enable it for testing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some audio codecs such as Intel HDA do not need to use digital data to
play sounds, but instead have a way to emit beeps. Add this interface as
an option. If the beep interface is not supported, then the sound uclass
falls back to the I2S interface.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a way check to whether HD audio is enabled. Use ioctl() to avoid
adding too many unusual operations to PCH.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This uclass currently has no tests. Add a sandbox driver and some simple
tests to provide basic coverage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: Use "sandbox,pch" for the compatible string, for consistency]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present this uclass is selected only on x86. In order to add a test for
it, it must also support sandbox. Create a new CONFIG_PCH option and
enable it on x86 and sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present these macros give warnings on 64-bit machines and do not
correctly do 32-bit accesses. Update them to use linux types.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This struct is getting larger and in some cases is being used for things
which would be better put into a driver. For example hwspinlock is not
used outside of sandbox_hwspinlock.c.
Add a note to encourage people to put things elsewhere.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Switch to using the omap3-u-boot.dtsi file for needed properties.
- Remove a few SPL features to free up more SRAM space.
- Switch CONFIG_SYS_TEXT_BASE to the normal default, we don't need to
worry about X-Loader at this point anymore.
- A few related updates to SPL options as part of switching to DM SPL.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
With the generic omap3-u-boot.dtsi file available, this patch
increased the memory of the various incarnations of the omap3_logic
board, and points their respective u-boot.dtsi files to the newly
created generic one, and removes the PLATDATA from the board file.
These are all done at once because the're all utilizing the same
omap3logic.c board file.
Signed-off-by: Adam Ford <aford173@gmail.com>
Create generic omap3-u-boot.dtsi file that omap3 based boards
can include to generate device tree in SPL for booting MLO.
Credit should go to Tom Rini.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
This commit converts the brxre1 board to DM,
for this we have todo following things:
- add a devicetree-file for this board
- drop all obsolete settings from board header-file
- use dm_i2c_xxx calls for read/write to the resetcontroller
- request gpios before operate them
Serues-cc: trini@konsulko.com
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
remove SCSI and SCSI_AHCI configs for ls1043ardb due to no sata interface
support.
this changed is to fixed the ls1043ardb compile warning as fallows:
===================== WARNING ======================
This board does not use CONFIG_DM_SCSI. Please update
the storage controller to use CONFIG_DM_SCSI before the
v2019.07 release. Failure to update by the deadline may
result in board removal.See doc/driver-model/MIGRATION.txt
for more info.
====================================================
Signed-off-by: Peng Ma <peng.ma@nxp.com>
[PK: reword the patch subject]
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Moves FSL_TZASC_400 and FSL_TZPC_BP147 configs to Kconfig
for LS1088A and LS2088A platforms.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
LX2160AQDS is a development board that supports LX2160A
family SoCs. This patch add base support for this board.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[PK: Sqaush patch for "secure boot defconfig" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
some dpmacs in armv8a based freescale layerscape SOCs can be
configured via both serdes(sgmii, xfi, xlaui etc) bits and via
EC*_PMUX(rgmii) bits in RCW.
e.g. dpmac 17 and 18 in LX2160A can be configured as SGMII from
serdes bits and as RGMII via EC1_PMUX/EC2_PMUX bits
Now if a dpmac is enabled by serdes bits then it takes precedence
over EC*_PMUX bits. i.e. in LX2160A if we select serdes protocol
that configures dpmac17 as SGMII and set the EC1_PMUX as RGMII,
then the dpmac is SGMII and not RGMII.
Therefore, move the fsl_rgmii_init after fsl_serdes_init. in
fsl_rgmii_init function of SOC, we will check if the dpmac is enabled
or not? if it is (fsl_serdes_init has already enabled the dpmac), then
don't enable it.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add code to initial ethernet interface arrays
with corresponding dpmac-id values in serdes_init function
for LX2160A.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
As per hardware documentation,
CONFIG_SYS_FSL_PEBUF_BASE for lx2160a is 0x1c00000000
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The 'dwmac_socfpga' ETH driver can now get the MACs out of reset
via the socfpga reset driver and can set PHY mode via syscon.
This means we can now remove the ad-hoc code to do this from
arch/arm/mach-socfpga.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
As the H5 is pin compatible with the H3, vendors tend to upgrade their
existing H3 products with an H5 SoC swap. This is the case with the
Bananapi M2+ H5.
Add the following to support it:
- device tree file: synced from Linux v5.0-rc1,
- defconfig: copy of bananapi_m2_plus_h3_defconfig with only SoC
family and default device tree file name changed
- MAINTAINERS entry
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
As of commit aa8fee415f46 ("ARM: dts: sun8i: h3: Split out
non-SoC-specific parts of Bananapi M2 Plus") in the Linux kernel, the
device tree for the Bananapi M2+ has been split into a common dtsi file,
and an SoC-specific board device tree file that includes both the shared
dtsi file and the soc dtsi file. This was done to support both the H3
and H5 variants of the same board. This is similar to what was done for
the Libre Computer ALL-H3-CC in U-boot commit d7b17f1c24 ("sunxi: Split
out common board design for ALL-H3-CC device tree").
The newly split files are directly synced from Linux tag v5.0-rc1.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This makes get_imx_reset_cause() accessible in SPL, but keeps the SRSR
register content intact so that U-Boot proper can evaluated the
reset_cause again should this be needed.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Update all the dts[i] files for imx6[q|qp|dl] sabre[auto|sd] to the ones
from kernel v4.20 (commit 8fe28cb58bcb2).
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This allows us to keep the basic dts[i] files up-to-date with
the ones in kernel, but at the same time allowing the u-boot
to add its own properties to the existing nodes.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Since there is the SPL_USB_HOST_SUPPORT for enabling USB support in SPL,
makes more sense to rename the SPL_USB_SUPPORT as SPL_USB_STORAGE.
Everything that is not part of the usb storage support in SPL is now
build under SPL_USB_HOST_SUPPORT.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
As per the zc1275 design x1 mode is enabled so changing the
spi-rx-bus-width property to x1.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The idle-states binding documentation[1] mentions that the
'entry-method' property is required on 64-bit platforms and must be
set to "psci".
Linux commit a13f18f59d26 ("Documentation: arm: Fix typo in the idle-states
bindings examples") attempted to fix this earlier but clearly more is
needed.
Linux docs:
Documentation/devicetree/bindings/arm/idle-states.txt (see
idle-states node)
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds reset-on-timeout to FPD WDT which will trigger an
interrupt to PMU when watchdog expiry happens and PMU takes the
necessary action. If this property is not enabled, reason will not be
known when watchdog expiry happens.
This patch also modifies the default timeout to 60 seconds. Reason is
that if u-boot enables WDT, it will set the timeout to 10 seconds and
this is not enough to boot till Linux and start the WDT application in
Linux. 60 seconds is the maximum safest value to boot till Linux and
start the WDT application.
Users need to change this timeout value to fit their needs.
Signed-off-by: Mounika Grace Akula <mounika.grace.akula@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Replace the current value of the model property by a more accurate
description of each board (which includes the manufacturer), as some
of the boards had the same value ("Xilinx Zynq")
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Both boards are made by Avnet, Inc. So add an additional
value to the compatible property
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Import liteSOM and liteboard dts files from Linux v4.20. They will
be used after transition to driver model and device-tree based boot.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This patch extends the vf610 DDR memory controller code to support SW
leveling.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
This patch provides the code to calibrate the DDR's
DQS to DQ signals (RDLVL).
It is based on:
VFxxx Controller Reference Manual, Rev. 0, 10/2016, page 1600
10.1.6.16.4.1 "Software Read Leveling in MC Evaluation Mode"
and NXP's community thread:
"Vybrid: About DDR leveling feature on DDRMC."
https://community.nxp.com/thread/395323
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Replace SDHCI controller listing by Kconfig symbol to let SPL know that
this board is using multiple SDHCIs controllers.
Kconfig help message should explain why this is needed.
Origin symbols were used in full u-boot but with moving to distro boot
this was fixed already.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
All platforms have been converted to DM that's why there is no reason to
keep addresses in headers. They are all read from DT now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
CONFIG_PCA953X is not needed because of PCA953X is integrated in gpio
subsystem already. That's why also remove CMD_PCA953X which is only for
this driver.
zcu102/zcu104-revC/zcu106/zcu111 contain links to eeprom which stores MAC address.
DM_I2C is not enabled for the whole SoC because it increase size for
mini configurations and there is no I2C symbol present to setup
dependencies.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
All platforms have been converted to DM that's why there is no reason to
keep addresses in headers. They are all read from DT now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Boards have only one controller enabled that's why move to DM_I2C is
easy.
Add also i2c alias for not to be shown as i2c bus -1 because alias
doesn't exist.
Config file points to MAC stored in eeprom but it is not listed that's
why I have added 24c08 part.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This patch adds new mini target for versal.
This configuration is very minimal in size which runs
from OCM. It contains support for mtest which can be
used for running DDR memory tests.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds mini eMMC configuration which has only
emmc0 and emmc1 functionalities and can run from small
amount of memory. This is required for memory constraint
devices.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new config option which is used for
reserving a specific memory for MMU Table and in this
case we are using TCM for that purpose.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Commit 81ea00838c ("efi_loader: PSCI reset and shutdown") put the SMCCC
assembly code into the efi specific code section. This is wrong when we
do not have EFI_LOADER enabled, as that strips efi runtime sections from
the output binary
Reported-by: Michal Simek <monstr@monstr.eu>
Reported-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Tested-by: Michal Simek <monstr@monstr.eu>
Fixes: 81ea00838c ("efi_loader: PSCI reset and shutdown")
Signed-off-by: Alexander Graf <agraf@suse.de>
arch/x86/lib/string.c contains assembler implementations of memcpy(),
memmove(), and memset() written for i386. Don't use it on x86_64.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Refactor the switch from supervisor to hypervisor to a new function called
at the beginning of do_bootefi().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
ARMv7-M only supports the Thumb instruction set. Our current crt0 code does
not support it. With the patch we can build all unit tests of the EFI
subsystem that do not require crt0.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Basin Cove PMIC is connected to I2C0 bus which is hidden from the OS
and access is going via SCU device, enumerated via PCI.
For now, we add just a minimum support of PMIC device to allow enabling,
e.g. USB OTG, in the OS.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
It is unnecessary to use a RAM version GDT for 64-bit U-Boot proper.
In fact we can just use the ROM version directly, which not only
eliminates the risk of being overwritten by application, but also
removes the complexity of patching the cpu_call64().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Before jumping to 64-bit U-Boot proper, SPL copies the cpu_call64()
function to a hardcoded address 0x3000000. This can have potential
conflicts with application usage. Switch the destination address
to be allocated from the heap to avoid such risk.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present the 4-level page table base address for 64-bit U-Boot
proper is assigned an address that conflicts with CONFIG_LOADADDR.
Change it to an address within the low memory range instead.
Fixes crashes seen when 'dhcp' on QEMU x86_64 with
"-net nic -net user,tftp=.,bootfile=u-boot".
Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The PCIe slot PERST signal is active low. Fix the gpio signal
description in the dts.
This happened to work because the pcie_dw_mvebu driver sets the reset
gpio level to 1 (high) to release the reset. The following commit will
fix that.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Common sound support
buildman environment support
of-platdata documentation improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlxf7igRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYKfggApQiL0Gv6NdGAQN+zfpjKY5a2QyjKsAxa
KLm3q8XyXIQXufMWOEPoW1iWm0iixpIFgChy8ff3m/OPDzsx99UXDTyvjitsSxtQ
5tFu8K78nUZT6OOE3HNhhlyW/xK442oKBzGt4MUt3kUZOELsCNuftgbJUWksHuO3
6pPrgt36E0uRGbUA4ioYCU336viJRPOOCdqb8hHViEihFj/IEv5T82RdE5y97YxG
dT7BZxjPkBH5ZN1uD/tdxG1k6IZBagZiYoDAsYp4YqNwmVsm5sLrZ9QVSf7EcH/y
qX8butZesiMd7xm7RROlrIImh7fb36N3zsoRiUWZDo1Al3IRkmZyVA==
=tdut
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-10feb19' of git://git.denx.de/u-boot-dm
Samsung sound patches (applied for Samsung maintainer)
Common sound support
buildman environment support
of-platdata documentation improvements
Now that these boards use driver model we can drop the old code. At
present s5p_mmc_init() is still used by goni and smdkv310 so cannot be
removed unless we remove those boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Update the flashmap so that this board can be started over USB A-A. It
is slightly different from snow.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Update the spring settings to use this codec, which is what it actually
shipped with.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Move all exynos boards over to use CONFIG_BLK.
This converts s5p_goni also, but adding dummy functions for pinmux and
peripheral ID. This will not function correctly, but gives the maintainer
more time to convert the board if desired.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Perform some cosmetic cleanup of the ATF image startup function, namely
fixing a spelling mistake, capitalization of a few words, spacing, as
well aligning how errors are printed and as using panic() for cases that
were using a combination of printf() + hang().
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This add the initial support of the broadcom reference
board bcm963158 with a bcm63158 SoC.
This board has 1 GB of ram, 512 MB of flash (nand),
2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This add the initial support of the broadcom bcm63158 SoC family,
only the cpu, dram and uart are supported.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
- Add st,digbypass on clk_hse node (needed for board rev.C)
- MLAHB/AHB max frequency increased from 200 to 209MHz, with:
- PLL3P set to 208.8MHz for MCU sub-system
- PLL3Q set to 24.57MHz for 48kHz SAI/SPI2S
- PLL3R set to 11.29MHz for 44.1kHz SAI/SPI2S
- PLL4P set to 99MHz for SDMMC and SPDIFRX
- PLL4Q set to 74.25MHz for EVAL board
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
not break functionality.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
commit fdce9d35dc ("arm: dts: am33xx: Sync dts with Linux 4.20.0")
did remove the "u-boot,dm-spl" flag from the 'ocp' bus which was
introduced with
commit 19aa4ac09d ("dts: am33xx: add u-boot, dm-spl to ocp bus")
Due to this all boards having CONFIG_SPL_OF_CONTROL enabled are broken
because they cannot bind/probe the boot-media interface during SPL
stage.
This commit introduces the 'am33xx-u-boot.dtsi' which is included with
the auto include mechanism. The am33xx-u-boot-dtsi adds the important
"u-boot,dm-pre-reloc" to the 'ocp bus' (the root bus of almost all
peripherals, at least the bootable ones).
The peripherials (mmc, spi, ...) needed during SPL stage need to be
equipped with the 'u-boot,dm-pre-reloc' in their responsible dts file.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
With the new DM_VIDEO support in the Armada XP LCD driver, this patch
adds the needed DT node for the LCD controller to the theadorable dts
file. This DT property is not added to the Armada XP dtsi files, as this
LCD feature is pretty unusual for this SoC and I personally know of no
other board that uses this controller.
This patch also enables CONFIG_BMP_16BPP/24BPP/32BPP, as the "old" bmp
command supported these BMP files.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
This patch moves the Armada XP video / LCD driver to DM_VIDEO. With this
move, the legacy interface board_video_init() is removed from the
theadorable board code (only user of this video driver). The support
via DT will be added in a separate patch.
This patch also enables DM_VIDEO for the theadorable board, as this is
needed to not break git bisect'ability.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
This adds initial support for micro-DPU (uDPU) board which is based on Armada-3720 SoC.
micro-DPU is the single-port FTTdp "distribution point unit" made by Methode Electronics
which offers complete modularity with replaceable SFP modules both for uplink and downlink
(G.hn over twisted-pair, G.hn over coax, 1G and 2.5G Ethernet over Cat-5e cable).
On-board features:
- 512 MiB DDR3
- 2 x 2.5G SFP via HSGMII SERDES interface to the A3720 SoC
- USB 2.0 Type-C connector
- 4GB eMMC
- ETSI TS 101548 reverse powering via twisted pair (RJ45) or coax (F Type)
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Luis Torres <luis.torres@methode.com>
Cc: Scott Roberts <scott.roberts@telus.com>
Cc: Paul Arola <paul.arola@telus.com>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Now that the PCIe driver supports DM and DT parsing, enable the PCIe DT
nodes that are used by this board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: VlaoMao <vlaomao@gmail.com>
This patch sync's the PCIe DT nodes with the recent Linux v4.20 version.
This change makes it easier to reference specific PCIe nodes in the
board dts files to e.g. enable a PCIe port as this is now necessary with
the new DM PCI driver for these platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: VlaoMao <vlaomao@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
* support for Chromebook Bob
* full pinctrl driver using DTS properties
* documentation improvements
* I2S support for some Rockchip SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcVG0IAAoJECaAFcEOcohNKVAIAJd3DN/qudcVQdkuvAGK6WIk
Umxkm6rxHwur7oU+wxvK1p1l/0YTFBeCfo15quH1DkSc/WIUnmBlLmDvqpGVmPmh
ydZNE9ZChn0OKRIaM6pKJr+3p155cQDe6Mgg2j/5CnNx28KxT+vu7EqZbZvbQPag
wcZEK6Z6E5jMVHVn2lbLgmsBPmY7ksX168IqpvzTxIj0a4J3n0DcJUnO4RBBS0Q2
PGEvFhTvigVWs6r6GL0gLn3VwnQX30xQlIuKKORPcdhjk97cJcS4+bRxdTENTKD9
j3+pgyl1n04O8sPONZS7pH3fvJwtC6SwnoxTYxGrvjedw1LxbyHG3cqcGDg/TJ8=
=ik3X
-----END PGP SIGNATURE-----
Merge tag 'for-master-20190201' of git://git.denx.de/u-boot-rockchip
u-boot-rockchip changes for 2019.04-rc1:
* support for Chromebook Bob
* full pinctrl driver using DTS properties
* documentation improvements
* I2S support for some Rockchip SoCs
With the latest changes to add support for the Chromebook Bob,
initialisation through debug_uart_init() did no longer get called for
other targets.
Fix this, by moving debug_uart_init() out of the Bob-specific
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Bob is a 10-inch chromebook produced by Asus. It has two USB 3.0 type-C
ports, 4GB of SDRAM, WiFi and a 1280x800 display. It uses its USB ports
for both power and external display. It includes a Chrome OS EC
(Cortex-M3) to provide access to the keyboard and battery functions.
Support so far includes only:
- UART
- SDRAM
- MMC, SD card
- Cros EC (but not keyboard)
Not included:
- Keyboard
- Display
- Sound
- USB
- TPM
Bob is quite similar to Kevin, the Samsung Chromebook Plus, but support
for this is not provided in this series.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add some U-Boot-specific settings. These should really go in the
*u-boot.dtsi file, but it seems that rk3399 does not use that yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Allow rockchip boards to use GPIOs before driver model is ready. This is
really only useful for setting GPIOs to enable the early debug console, if
needed on some platforms.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
At present this enum is only available to rk3288. Move it so that other
rockchip SoCs can access it. It is needed for the SPL GPIO driver for
rk3999 in a later patch.
Also adjust the enum name to lower case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
These board files have inconsistent #include ordering. Fix them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This memory is used on Bob. Add settings for this, taken from coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The u-boot,spl-boot-device property only allows MMC at present. Add SPI as
well for boards that boot from SPI flash.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This file has changed upstream, with some additions and changes. Move the
U-Boot version towards this.
Some USB changes seem to be incompatible with how the bindings work on
rockchip in U-Boot. Testing is needed to make sure that USB still works
correct, and adjust the code (not device tree) if not.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Bring in these files from Linux v4.20.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
To match the iomux setting of uart2 at SPL, correct the uart2
default pin configuration, if not changed, the evb-rk3229 can't
output the log message.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
If we use the new pinctrl driver, the pinctrl setup will be done
by device probe. Remove the pinctrl setup at rk3288-board-spl.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
It seems that pinctrl is not requested for rk3188 SPL, remove it so
that can save more space for SPL image size.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
When the boot ROM sets up MMC we don't need to do it again. Remove the
MMC setup code entirely, but we also need to enable uart for debug message.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This adds support for the ASUS C201, a RK3288-based clamshell
device. The device tree comes from linus's linux tree at
3f16503b7d2274ac8cbab11163047ac0b4c66cfe. The SDRAM parameters
are for 4GB Samsung LPDDR3, decoded from coreboot's
src/mainboard/google/veyron/sdram_inf/sdram-lpddr3-samsung-4GB.inc
Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Like on rk3399-puma we want to continue booting the fill U-Boot from
the same device as the SPL stage.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This function causes a 5-second delay and stops the display working on
minnie. This code should be in a driver and should only be enabled by
a device-tree property, so that it does not affect devices which do not
have this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Jerry uses a max98090 audio codec and the internal SoC I2S peripheral.
Enable sound support and add the required device-tree pieces.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add support for setting pinctrl and clock for I2S on rk3288. This allows
the sound driver to operate. These settings were created by rkmux.py
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Although not required, it doesn't hurt to explicitly map the USB ports to
a USB controller. Without this, the port number will be derived from the
binding order of the peripheral devices.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPLY_FS_EXT4 so both
obj-$(CONFIG_$(SPL_)FS_EXT4) and CONFIG_IS_ENABLED(FS_EXT4) can be
used to control the build in both SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT so
obj-$(CONFIG_$(SPL_)FS_FAT) can be used to control the build in both
SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This USB port is mainly used for RNDIS and DFU. To be able to use it with
DM_USB and DM_USB_GADGET, we need to provide a dr_mode value in the DTS.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
add u-boot specific am335x-shc-u-boot.dtsi file,
in which we add u-boot specific adaptions.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
add DTS from linux tree commit
"47bfa6d9dc8c060bf56554a465c9031e286d2f80"
change for U-Boot:
switch to SPDX-license identifier.
Signed-off-by: Heiko Schocher <hs@denx.de>
If VIDEO_MESON is enabled, we need to setup the fdt for the framebuffer.
Call meson_vpu_rsv_fb() which reserves the framebuffer memory region for
EFI, and sets up simple-framebuffer nodes if simplefb support is
enabled.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
There's no reliable way to reuse the hhi entry from the vpu as is done
in the linux kernel, so we duplicate it here.
We will be able to sync against kernel DTS in the future when the VPU
gets based on the clock framework rather than the HHI reg.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The hdmi_5v regulator must be enabled to provide power to the physical HDMI
PHY and enables the HDMI 5V presence loopback for the monitor.
Fixes: b409f625a6d5 ("ARM64: dts: meson-gx: Add HDMI_5V regulator on selected boards")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
[backport of linux commit e1f2163deac059ad39f07aba9e314ebe605d5a7a]
Flag the appropriate nodes with u-boot,dm-pre-reloc
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds video output support for Amlogic GXBB/GXL/GXM chips.
The supported ports are CVBS and HDMI (based on DW_HDMI).
When using HDMI, only DMT modes are supported.
There is support for simple-framebuffer (CONFIG_VIDEO_DT_SIMPLEFB)
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jorge Ramire-Ortiz <jramirez@baylibre.com>
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
[narmstrong: fixed defines alignment in meson_canvas.c]
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Enable DM_MMC for all Allwinner SoCs, this will eventually
enable BLK.
Also removed DM_MMC enablement in few parts of sunxi
configurations.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Like other Allwinner A64 boards, pinebook also need altering
auto-numbering of mmc2 to mmc1 which is available in common
sunxi dsti file, sunxi-u-boot.dtsi
Pinebook has a separate sun50i-a64-pinebook-u-boot.dtsi which
takes more precedence for u-boot.dtsi inclusion and it eventually
failed to include the sunxi-u-boot.dtsi.
So, this patch add support to include the sunxi-u-boot.dtsi in the
sun50i-a64-pinebook-u-boot.dtsi
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com> # Pinebook
Environment and fastboot mmc devices are configured based on the number
of mmc slots defined on particular board configs, MMC_SUNXI_SLOT_EXTRA.
If MMC_SUNXI_SLOT_EXTRA is more than 1, the default env and fastboot
mmc devices is mmc1 by assuming mmc0 is SD and mmc1 is emmc device.
But with DM_MMC the mmc devices are numbered as per the dts node
enablement. If there is a chance of having enabling all mmc nodes
in dts say mmc0, mmc1, mmc2 then the default env and fastboot devices
will failed to assign proper emmc device since mmc2 is emmc in most
of the Allwinner platforms.
So, we need to alter the auto-numbering by aliasing mmc2 to mmc1 since
aliases take precedence over auto-numbering.
If the dts enables mmc0, mmc1, mmc2, then all the nodes will probe
sequentially and auto-numbered as it is. but when aliases mmc1 with mmc2
the resulting number should be that mmc0 is till mmc0, mmc2 become mmc1
and mmc2 become mmc1
Without aliases of mmc1 = &mmc2;
-------------------------------
MMC: mmc@1c0f000: 0, mmc@1c10000: 1, mmc@1c11000: 2
With aliases of mmc1 = &mmc2;
----------------------------
MMC: Device 'mmc@1c11000': seq 1 is in use by 'mmc@1c10000'
mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1
Loading Environment from FAT... OK
Some platforms like A20 has mmc0...mmc3, but there is no usecases now
for enabling all mmc controllers in any of A20 board dts files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Update generation of spl binaries
- continue to generate all SPL files in spl sub-directory
- copy in root folder the needed file for user (YOCTO, buildroot):
u-boot-spl.stm32
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
When framebuffer driver init is failed, we should return the err value not 0.
So the video init can exit immediately.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The i.MX6 SOM and development kits have undergone significant
updates and changes over the past few months. This re-sync's
the U-Boot with Logic PD's BSP.
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch sets up an alias for mmc0 to usdhc3.
Before the DM conversion only usdhc3 was enabled and therefore it appeared
as MMC 0 to u-boot. After enabling MMC DM though usdhc3 defaults to MMC 2,
which left unattended would drive changes to existing warp7 bootscripts and
environment variables that rely on mmc 0.
Setup the alias of mmc0 and usdhc3 so that existing warp7 boot code will
work unmodified.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
This patch imports the Linux kernel warp7 dts as at upstream kernel commit
cf76c364a1e1.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
As pointed out by Lucas WDOD1_WDOG_ANY should be WDOG1_WDOG_ANY. Once
corrected we can import the latest kernel DTS unmodified.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reported-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Passover info only for revA.
move get_cpu_rev out of CONFIG_CPU to avoid build failure when using
get_cpu_rev in SPL.
Add a CONFIG_SPL_BUILD for passover usage, no need to execute it again
in normal U-Boot stage. Also if still checking passover info in normal
U-Boot stage, need to make the passover code executed after
arch_cpu_init_dm.
So to make it easy and clean, only execute the code for SPL stage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Apply errata based on PL310 version instead of compile
time. Also set Prefetch offset to 15, since it improves
memcpy performance by 35%. Don't enable Incr double
Linefill enable since it adversely affects memcpy
performance by about 32MB/s and reads by 90MB/s. Tested
with 4K to 16MB sized src and dst aligned buffer.
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
According to "Table 5-1. Boot Device Select" (page 335,
i.MX 6Dual/6Quad Applications Processor Reference Manual, Rev. 4, 09/2017)
the BOOT_CFG1[3] have following values (regarding EIM booting):
0 - NOR flash and 1 - ONENAND
This commit provides correct identification of the boot medium for IMX6Q
boards booting from NOR memory (MCCMON6 is one of them).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
These nodes are required by CX9020 when build with CONFIG_DM_MMC=y
They are copied from Linux 4.20
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>