Some config symbols are found in *almost* every _defconfig file for
Allwinner boards, because those options are actually a platform choice,
and not a per-board decision.
Some of these options are older, some have recently been added.
Move those options to be set for all Allwinner boards in their
respective Kconfig files.
The rationales are as follows:
- NR_DRAM_BANKS: All Allwinner SoC map DRAM at one contiguous region of
address space only, starting at 1 GB. So it's always one bank.
- SPL_{DOS,EFI}_PARTITION: The Allwinner SPL does only support raw MMC
accesses, we don't care about filesystems or partitions in there, so
there is no need to define those symbols at all.
- USE_PREBOOT: We start USB early when a keyboard is configured, using the
preboot env variable, so we need to set this variable.
- SYS_RELOC_GD_ENV_ADDR: We don't specify any ENV_ADDR, so need this
symbol to be set (according to 8d8ee47e03).
- SYS_USB_EVENT_POLL_VIA_INT_QUEUE: According to commit eab9433aa5,
specifying this reduces the latency of the USB keyboard handling, so
this was formerly enabled in config headers for all Allwinner boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The binman-option BINMAN_FDT is introduced by this commit:
commit 3c10dc95bd ("binman: Add a library to access binman entries")
BINMAN_FDT being selected when BINMAN=y that resulting in mt7623
and mt7622 are unable to boot. The root cause of this issue is commit:
commit cbd2fba1ec ("arm: MediaTek: add basic support for MT7629 boards")
select BINMAN=y in all mediatek SoCs, and others mediatek SoCs not
expect to use BINMAN_FDT.
This patch remove BINMAN=y option when ARCH_MEDIATEK=y and
move this to the specify SoCs part config.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
UCLASS_MTD is a better fit for NAND drivers.
Make NAND_DENALI_DT depend on DM_MTD, which is needed to compile
drivers/mtd/mtd-uclass.c
Also, make ARCH_UNIPHIER select DM_MTD because all the defconfig
of this platform enables NAND_DENALI_DT.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
All rockchip platforms support TPL or SPL-based bootloader
in mainline with U-Boot proper as final stage. For each
stage we need to burn the image on to flash with respective
offsets.
This patch creates a single boot image component using
- binman, for arm32 rockchip platforms
- pad_cat, for arm64 rockchip platforms.
This would help users to get rid of burning different
boot stage images.
The new image called 'u-boot-rockchip.bin'
which can burn into flash like:
₹ sudo dd if=u-boot-rockchip.bin of=/dev/sda seek=64
This would support all rockchip platforms, except rk3128
since it doesn't support for SPL yet.
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Currently LS1028A board code uses arch_misc_init to set up the board mux
on QDS. Move this code to misc_init_r. This is consistent with LS gen 2
and T series SoCs/boards.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The arch_misc_init function is empty on LS108x SoCs/boards, remove it.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The arch_misc_init function is empty on LS2 SoCs/boards, remove it.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently LX2 board code uses arch_misc_init to set up the board mux on
RDB and QDS. Move this code to misc_init_r. This is consistent with LS
gen 2 and T series SoCs/boards.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This add the initial support of the broadcom reference
board bcm968360bg with a bcm68360 SoC.
This board has 512 MB of RAM, 256 MB of flash (nand),
2 USB port, 1 UART, and 4 ethernet ports.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
The NovaThor U8500 SoC was released by ST-Ericsson in 2011.
It was used for some development boards like the CALAO Systems
Snowball SBC, but mass production was primarily for Android
smartphones like the Samsung Galaxy S III mini.
Previous support for U8500 was removed in
commit 68282f55b8 ("arm: Remove unused ST-Ericsson u8500 arch")
since none of the boards were converted to generic boards
before the deadline.
The new code does not have much in common with the previous code.
I have completely rewritten everything, embracing the Driver Model
and device trees wherever possible.
The U8500 support is a bit more minimal for now - my primary
use case is to use U-Boot as alternative bootloader for some of the
U8500 Samsung smartphones. At the moment U-Boot is chain-loaded from
the original Samsung bootloader. A side effect of this is that we
can (temporarily) get away without implementing some functionality
- e.g. all clocks are already enabled by the original bootloader.
More functionality will be added in future patches.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: John Rigby <john.rigby@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
When position-independent pre-relocation code is enable there is also
necessary to enable relative early stack pointer not to use origin location
pointed by CONFIG_SYS_INIT_SP_ADDR macro.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Programs the following:
1. Redistributor PROCBASER configuration table (which
is common for all redistributors)
2. Redistributor pending table (PENDBASER), for all the
available redistributors.
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Add build support for Agilex SoC.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
In the case of i.MX6 and i.MX7 family SoCs it is safe (from an errata
point of view) to use thumb2 by default to save space.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
We shouldn't force which allocator the SPL uses, since there's no
platform requirement for one over the other: in fact, we currently allow
selection of the TPL allocator but not the SPL one!
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This adds platform code and the device tree for the Phytium Durian Board.
The initial support comprises the UART and the PCIE.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Steven Hao <liuhao@phytium.com.cn>
board_early_init_f added by commit e6cc3b25d7
("arm: zynq: Wire watchdog internals") is no longer needed that's why
remove it also with Kconfig enabling.
Fixes: ccd063e981 ("watchdog: Move watchdog_dev to data section (BSS may not be cleared)")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
U-Boot cannot be built for h2200_defconfig with CONFIG_DM=y.
The maintainer Lukasz Dalek suggested to remove the board.
https://lists.denx.de/pipermail/u-boot/2019-August/380685.html
Cc: Lukasz Dalek <luk0104@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[trini: As this is the last non-toradex PXA board, update travis too]
Signed-off-by: Tom Rini <trini@konsulko.com>
When running SPL on iMX8, the A core starts at address 0
which is a alias to OCRAM 0x100000.
The alias only map first 96KB of OCRAM, so this require the
SPL size can't beyond 96KB. But when using SPL DM, the size increase
significantly and may exceed 96KB.
So to fix the problem, we will change SPL linker address to OCRAM
address 0x100000. And then jump to the absolute address not the PC relative
address for entering OCRAM.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
CONFIG_SECURE_BOOT is too generic and forbids to use it for cross
architecture purposes. If Secure Boot is required for imx, this means to
enable and use the HAB processor in the soc.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Probe ZynqMP firmware driver on the board initialization phase and
ensure that firmware is in place to continue execution. The probing is
done on board_init so it can be used for both SPL and U-Boot proper.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
zynqmp-power driver for ZynqMP to handle the communication with the PMU
firmware. Firmware driver just probes subnodes and power driver handles
communication with PMU using the IPI mailbox driver.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is setting up the initrd_high to as high as possible by leaving
max stack size for u-boot so that bigger rootfs can also be loaded by
u-boot for booting kernel.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is setting up the initrd_high to as high as possible by leaving
max stack size for u-boot so that bigger rootfs can also be loaded by
u-boot for booting kernel.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define board_late_init which performs bootmode detection
and prepares corresponding distro boot commaand sequence.
Also disable it for mini platforms because simply there is no need to have
it enabled.
But also disable it for virtual platform because Qemu is not modelling this
register space that's why travis testing would fail. This configuration
should be reverted when mainline Qemu is updated.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
At present there is only one control for this and it is used for both SPL
and TPL. But SPL might have a lot more space than TPL so the extra cost of
a full printf() might be acceptable.
Split the option into two, providing separate SPL and TPL controls. The
TPL setting defaults to the same as SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This reverts commit fc04b92354 where the
FVP DRAM configuration was added.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Add imply for FDT overlay that can be usefuill for kernel device tree
management but it is not mandatory (can be removed to gain space)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This converts the following to Kconfig:
CONFIG_ARCH_CPU_INIT
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Felix Brack <fb@ltec.ch>
Several options are presenting themselves on a various boards
where the options are clearly not used. (ie, arm64 options on
arm9, or SPL/TPL options when SPL or TPL are not defined)
This patch is not attempting to be a complete list of items, but
more like low hanging fruit.
This patch attempts to reduce some of the menuconfig noise
by defining dependencies so they don't appear when not used.
Signed-off-by: Adam Ford <aford173@gmail.com>
Select BOARD_LATE_INIT for ls1028ardb and ls1028aqds targets
so that late init work can be done.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This commit adds board support for Hikey960 board from Hisilicon. This
board is one of the Consumer Edition boards of the 96Boards family
powered by Kirin960 SoC.
More information about this board can be found in 96Boards website:
https://www.96boards.org/product/hikey960/
The initial supported/tested devices include:
- Debug serial
- SD
With these support, it's good enough for loading Linux Kernel from SD.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The LS1021A-TSN is a development board built by VVDN/Argonboards in
partnership with NXP.
It features the LS1021A SoC and the first-generation SJA1105T Ethernet
switch for prototyping implementations of a subset of IEEE 802.1 TSN
standards.
Supported boot media: microSD card (via SPL), QSPI flash.
Rev. A of the board uses a Spansion S25FL512S_256K serial flash, which
is 64 MB in size and has an erase sector size of 256KB (therefore,
flashing the RCW would erase part of U-Boot).
Rev. B and C of the board use a Spansion S25FL256S1 serial flash, which
is only 32 MB in size but has an erase sector size of 64KB (therefore
the RCW image can be flashed without erasing U-Boot).
To avoid the problems above, the U-Boot base address has been selected
at 0x100000 (the start of the 5th 256KB erase sector), which works for
all board revisions. Actually 0x40000 would have been enough, but
0x100000 is common for all Layerscape devices.
eTSEC3 is connecting directly to SJA1105 via an RGMII fixed-link, but
SJA1105 is currently not supported by uboot. Therefore, eTSEC3 is
disabled.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Jianchao Wang <jianchao.wang@nxp.com>
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
[Vladimir] Code taken from https://github.com/openil/u-boot (which
itself is mostly copied from ls1021a-iot) and adapted with the following
changes:
- Add a008850 errata workaround
- Converted eTSEC, MMC to DM to avoid all build warnings
- Plugged in distro boot feature, including support for extlinux.conf
- Added defconfig for QSPI boot
- Added the board/freescale/ls1021atsn/README.rst for initial setup
- Increased CONFIG_SYS_MONITOR_LEN so that the SPL malloc pool does not
get overwritten during copying of the u-boot.bin payload from MMC to
DDR.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This moves sysreset support for socfgpa from ad-hoc code in mach-socfpga
to a UCLASS_SYSRESET based dm driver.
A side effect is that gen5 and a10 can now select between cold and warm
reset.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
If U-Boot is loaded and started from TF-A (you need to change
SYS_TEXT_BASE to 0x60000000), it will hang up at flash initialization.
If secure mode is off (default, or -machine virt,secure=off) at qemu,
it will provide dtb with two flash memory banks:
flash@0 {
bank-width = <0x4>;
reg = <0x0 0x0 0x0 0x4000000 0x0 0x4000000 0x0 0x4000000>;
compatible = "cfi-flash";
};
If secure mode is on, on the other hand, qemu provides dtb with 1 bank:
flash@0 {
bank-width = <0x4>;
reg = <0x0 0x4000000 0x0 0x4000000>;
compatible = "cfi-flash";
};
As a result, flash_init()/flash_get_size() will eventually fail.
With this patch applied, relevant CONFIG values are modified.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently, CONFIG_TFABOOT is located in armv8/fsl-layerscape Kconfig,
but it will be also useful for other targets if some additional
configuration are necessary.
So move it to arch/arm/Kconfig.
Please note that CONFIG_TFABOOT still depends on
CONFIG_ARCH_SUPPORT_TFABOOT and so the menu won't come up
if any target doesn't need its own customization for TF-A boot.
This will maintain the compatibility.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Sriram Dash <sriram.dash@nxp.com>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Peng Ma <peng.ma@nxp.com>
Cc: Yuantian Tang <andy.tang@nxp.com>
Cc: Pankit Garg <pankit.garg@nxp.com>
Probably for no particular reason SUNXI_GPIO was still defined the "old
way", in header files only.
Introduce SUNXI_GPIO to the Kconfig file in drivers/gpio to remove
another line from our dreadful config_whitelist.txt.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
By default, CONFIG_SYS_INIT_SP_BSS_OFFSET was made invisible by not
giving a prompt to it.
The only way to define it is to hard-code an extra entry in SoC/board
Kconfig, like arch/arm/mach-tegra/tegra{186,210}/Kconfig.
Add a prompt to it in order to allow defconfig files to specify the
value of CONFIG_SYS_INIT_SP_BSS_OFFSET.
With this, CONFIG_SYS_INIT_SP_BSS_OFFSET would become always visible.
So, we need a new bool option to turn it off by default.
I move the 'default 524288' to the common place. This value is not too
big, but is big enough to avoid the overwrap of DT in most platforms.
If 512KB is not a suitable choice for your platform, you can change it
from your defconfig or menuconfig etc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
- LS1046AFRWY support
- USB errata fix and secure boot defconfig support for LS1028A
- Enabled SDHC and SATA for LX2160
- LS1046A serdes fixes
- other minor fixes
Per discussion on the list, drop this board again.
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
LS1028A is an ARMv8 implementation. LS1028ARDB is an evaluation
platform that supports the LS1028A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
CONFIG_SYS_[DI]CACHE_OFF had been partially converted to Kconfig
parameters; only for the ARC architecture. This patch turns these two
parameters into Kconfig items everywhere else they are found.
All of the include/configs/* and defconfig changes in this patch are
for arm machines only. The Kconfig changes for arc, nds32, riscv,
and xtensa have been included since these symbols are found in code
under arch/{arc,nds32,riscv,xtensa}, however, no currently-defined
include/configs/* or defconfigs for these architectures exist which
include these symbols.
These results have been confirmed with tools/moveconfig.py.
Acked-by: Alexey Brodkin <abrodkin@snopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Re-migrate for a few more boards]
Signed-off-by: Tom Rini <trini@konsulko.com>
Some options like TPL_SYS_THUMB_BUILD, TPL_USE_ARCH_MEMCPY
and TPL_USE_ARCH_MEMCPY are needed for TPL build in 32bit arm.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add platform code and DTs for Renesas RZ/A1 R7S72100 SoC.
Distinguishing feature of this SoC is that it has up to
10 MiB of on-SoC static RAM (SRAM).
The DTs are imported from Linux 5.0.11, commit d5a2675b207d .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Select the PL310 UCLASS_CACHE driver for SoCFPGA.
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
-----BEGIN PGP SIGNATURE-----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=CzWQ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20190426' of git://git.denx.de/u-boot-imx
Porting to DM and i.MX8
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
All Rockchip SoCs use DEBUG_UART_BOARD_INIT to init per board
UART IOMUX, enable it by default.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
K3 devices have High Security (HS) variants along with the non-HS already
supported. Like the previous generation devices (OMAP/Keystone2) K3
supports boot chain-of-trust by authenticating and optionally decrypting
images as they are unpacked from FIT images. Add support for this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
This commit moves common config options used in all socfpga boards
to select/imply in Kconfig. This both cleans up the defconfig files
as well as makes future changes easier.
Options implied/defaulted for all sub-arches:
- SPL, SPL_DM, USE_TINY_PRINTF, NR_DRAM_BANKS
Options implied/defaulted for implied for A10 & gen5:
- FPGA_SOCFPGA, SYS_MALLOC_F_LEN, SYS_TEXT_BASE
Options implied/defaulted for gen5:
- SPL_STACK_R, SPL_SYS_MALLOC_SIMPLE, SPL_STACK_R_ADDR
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
- Enable DM_MMC if MMC defined
- Enable DM_SCSI if SCSI defined
globally through Allwinner platform, the effected SoC families
and boards will make use of MMC and SCSI subsystems in driver-model.
Tested DM_MMC in one board from A64, H6, H5, H3, R40, A83T, A20, A10
SoCs.
Tested-by: Pablo Sebastián Greco <pgreco@centosproject.org> # BPI-M2-Ultra
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Activate the command poweroff by default for STM32MP1:
- with PCSI from TF-A for trusted boot
- with PMIC sysreset request for basic boot (SYSRESET_POWER)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Set board name with the first dts compatible found in DT
code under CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
The result with DEVICE_TREE=stm32mp157c-ev1 is:
STM32MP> env print
board=stm32mp1
board_name=stm32mp157c-ev1
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of trusted boot, using TF-A as first stage bootloader,
The boot sequence is
BootRom >=> TF-A.stm32 (clock & DDR) >=> U-Boot.stm32
The TF-A monitor provides secure monitor with support of SMC
- proprietary to manage secure devices (BSEC for example)
- PSCI for power
The same device tree is used for STMicroelectronics boards with
basic boot and with trusted boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The ISW_ENTRY_ADDR Kconfig option under mach-omap2 isn't a SoC specific
notion but rather "where is our previous stage loaded in memory?"
option. Make use of this on ARCH_KEYSTONE rather than SPL_TEXT_BASE for
our HS builds that are not using SPL anyhow.
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com?
Enabling DM_MMC is forcing CONFIG_BLK=y so if any board which uses
SCSI must need to enable DM_SCSI otherwise SCSI reads on that particular
target making invalid reading to the disk drive.
Allwinner platform do support SCSI on A10, A20 and R40 SoC's out of
these only A10 have DM_SCSI enabled. So enabling DM_MMC on A20, R40
would eventually end-up with scsi disk read failures like [1]
So, enable DM_MMC in all places of respective SoC's instead of enabling
them globally to Allwinner platform.
Now, DM_MMC is enabled in Allwinner SoC's except A20 and R40.
[1] https://lists.denx.de/pipermail/u-boot/2019-April/364057.html
Reported-by: Pablo Sebastián Greco <pgreco@centosproject.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
remove SCSI and SCSI_AHCI configs for ls1043ardb due to no sata interface
support.
this changed is to fixed the ls1043ardb compile warning as fallows:
===================== WARNING ======================
This board does not use CONFIG_DM_SCSI. Please update
the storage controller to use CONFIG_DM_SCSI before the
v2019.07 release. Failure to update by the deadline may
result in board removal.See doc/driver-model/MIGRATION.txt
for more info.
====================================================
Signed-off-by: Peng Ma <peng.ma@nxp.com>
[PK: reword the patch subject]
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
LX2160AQDS is a development board that supports LX2160A
family SoCs. This patch add base support for this board.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[PK: Sqaush patch for "secure boot defconfig" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This add the initial support of the broadcom reference
board bcm963158 with a bcm63158 SoC.
This board has 1 GB of ram, 512 MB of flash (nand),
2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This add the initial support of the broadcom bcm63158 SoC family,
only the cpu, dram and uart are supported.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Enable DM_MMC for all Allwinner SoCs, this will eventually
enable BLK.
Also removed DM_MMC enablement in few parts of sunxi
configurations.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Similar changes was done for Zynq in past and this patch just follow
this pattern to separate cpu code from SoC code.
Move arch/arm/cpu/armv8/zynqmp/* -> arch/arm/mach-zynqmp/*
And also fix references to these files.
Based on
"ARM: zynq: move SoC sources to mach-zynq"
(sha1: 0107f24036)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CLK and DM_RESET drivers are now available for all of
the Allwinner platforms, so enable them in arch/arm/Kconfig
Enabling CLK will select DM_RESET by default.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
There is no code for using partition labels in the Allwinner SPL port.
Even so the name is slightly misleading, CONFIG_SPL_LIBDISK_SUPPORT was
meant to guard partition code for the SPL.
Remove the "imply" line in the Kconfig to make this obvious and avoid
unneeded code inclusions, helping to keep the H6 SPL code small.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch allows smaller binaries.
This is needed for and has been tested on Arndale board, as u-boot.bin is
now bigger than the 512K load limit, with GCC8, without thumb mode.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>