Scrub duplicate /memory@* node entries here. Some R-Car DTs might
contain multiple /memory@* nodes, however fdt_fixup_memory_banks()
either generates single /memory node or updates the first /memory
node. Any remaining memory nodes are thus potential duplicates.
However, it is not possible to delete all the memory nodes right
away, since some of those might not be DRAM memory nodes, but some
sort of other memory. Thus, delete only the memory nodes which are
in the R-Car3 DBSC ranges.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add CPSW related nodes for AM642 SK. There are two CPSW ports on the
board but U-Boot supports only the first port.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
AM64 as CPSW3G IP with 2 external ports. Add DT entries for the same
(based on kernel DT).
Disable second port as its by default set to ICSS usage on EVM.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
AM642 StarterKit (SK) board is a low cost, small form factor board
designed for TI’s AM642 SoC. It supports the following interfaces:
* 2 GB LPDDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in switch and MAC mode
* x1 USB 3.0 Type-A port
* x1 UHS-1 capable µSD card slot
* 2.4/5 GHz WLAN + Bluetooth 4.2 through WL1837
* 512 Mbit OSPI flash
* x2 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin Raspberry Pi compatible GPIO header
* 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO)
* 54-pin header for Programmable Realtime Unit (PRU) IO pins
* Interface for remote automation. Includes:
* power measurement and reset control
* boot mode change
Add basic support for AM642 SK.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Enable support for selecting DTB within SPL based on EEPROM.
This will help to use single defconfig for both EVM and SK
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
I2C EEPROM data contains the board name and its revision.
Add support for:
- Reading EEPROM data and store a copy at end of SRAM
- Updating env variable with relevant board info
- Printing board info during boot.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In SPL, DDR should be made available by the end of board_init_f()
so that apis in board_init_r() can use ddr. Adding support for
triggering DDR initialization from board_init_f().
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Introduce ddr node for am642 needed for all ddr configurations.
Also, introduce the 1600MTs DDR4 configuration that is supported on the
am642-evm.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
The AM642 EValuation Module (EVM) is a board that provides access to
various peripherals available on the AM642 SoC, such as PCIe, USB 2.0,
CPSW Ethernet, ADC, and more.
Add basic support.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
The AM642 SoC belongs to the K3 Multicore SoC architecture platform,
providing advanced system integration to enable applications such as
Motor Drives, PLC, Remote IO and IoT Gateways.
Some highlights of this SoC are:
* Dual Cortex-A53s in a single cluster, two clusters of dual Cortex-R5F
MCUs, and a single Cortex-M4F.
* Two Gigabit Industrial Communication Subsystems (ICSSG).
* Integrated Ethernet switch supporting up to a total of two external
ports.
* PCIe-GEN2x1L, USB3/USB2, 2xCAN-FD, eMMC and SD, UFS, OSPI memory
controller, QSPI, I2C, eCAP/eQEP, ePWM, ADC, among other
peripherals.
* Centralized System Controller for Security, Power, and Resource
Management (DMSC).
See AM64X Technical Reference Manual (SPRUIM2, Nov 2020)
for further details: https://www.ti.com/lit/pdf/spruim2
Introduce basic support for the AM642 SoC to enable SD/MMC boot.
Introduce a limited set of MAIN domain peripherals under cbass_main and
a set of MCU domain peripherals under cbass_mcu.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Change the memory attributes for the DDR regions used by the remote
processors on AM65x so that the cores can see and execute the proper code.
A separate table based on the previous K3 SoCs is introduced since the
number of remote processors and their DDR usage is different between the
SoC families.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
The AM642 SoCs use the Main R5FSS0 as a boot processor, and runs
the R5 SPL that performs the initialization of the System Controller
processor and starting the Arm Trusted Firmware (ATF) on the Arm
Cortex A53 cluster. The Core0 serves as this boot processor and is
parked in WFE after all the initialization. Core1 does not directly
participate in the boot flow, and is simply parked in a WFI.
Power down these R5 cores (and the associated RTI timer resources
that were indirectly powered up) after starting up ATF on A53 by
using the appropriate SYSFW API in release_resources_for_core_shutdown().
This allows these Main R5F cores to be further controlled from the
A53 to run regular applications.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Use the System Firmware (SYSFW) loader framework to load and start
the SYSFW as part of the AM642 early initialization sequence. Also
make use of existing logic to detect if ROM has already loaded sysfw
and avoided attempting to reload and instead just prepare to use already
running firmware.
While at it also initialize the MAIN_UART1 pinmux as it is used by SYSFW
to print diagnostic messages.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
For AM642, ROM supports loading system firmware directly
from boot image. ROM passes information about the number of
images that are loaded to bootloader at a specific address
that is temporary. Add support for storing this information
somewhere permanent before it gets corrupted.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
To access various control MMR functionality the registers need to
be unlocked. Do that for all control MMR regions in the MAIN domain.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
AM642 allows for booting from primary or backup boot media.
Both media can be chosen individually based on switch settings.
ROM looks for a valid image in primary boot media, if not found
then looks in backup boot media. In order to pass this boot media
information to boot loader, ROM stores a value at a particular
address. Add support for reading this information and determining
the boot media correctly.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
The AM642 SoC belongs to the K3 Multicore SoC architecture platform,
providing advanced system integration to enable applications such as
Motor Drives, PLC, Remote IO and IoT Gateways.
Some highlights of this SoC are:
* Dual Cortex-A53s in a single cluster, two clusters of dual Cortex-R5F
MCUs, and a single Cortex-M4F.
* Two Gigabit Industrial Communication Subsystems (ICSSG).
* Integrated Ethernet switch supporting up to a total of two external
ports.
* PCIe-GEN2x1L, USB3/USB2, 2xCAN-FD, eMMC and SD, UFS, OSPI memory
controller, QSPI, I2C, eCAP/eQEP, ePWM, ADC, among other
peripherals.
* Centralized System Controller for Security, Power, and Resource
Management (DMSC).
See AM64X Technical Reference Manual (SPRUIM2, Nov 2020)
for further details: https://www.ti.com/lit/pdf/spruim2
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
-----BEGIN PGP SIGNATURE-----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=aTso
-----END PGP SIGNATURE-----
Merge tag 'v2021.07-rc2' into 2021.07+fslc
Prepare v2021.07-rc2
* tag 'v2021.07-rc2':
Prepare v2021.07-rc2
MAINTAINERS: Add an entry for VirtIO
doc: develop: Convert README.virtio to reST
x86: Correct regwidth prompt in cbsysinfo
cmd/exception: support ebreak exception on RISC-V
atcspi200: Add timeout mechanism in spi_xfer()
riscv: cpu: fu740: clear feature disable CSR
riscv: cpu: Add callback to init each core
fdt_support.c: Allow late kernel cmdline modification
cmd: gpt: Add option to write GPT partitions to environment variable
sandbox: add test of CONFIG_ENV_IMPORT_FDT
env: allow environment to be amended from control dtb
test: Add gpio-sysinfo test
sysinfo: Add gpio-sysinfo driver
sysinfo: Require that sysinfo_detect be called before other methods
sysinfo: Use global sysinfo IDs for existing sysinfo drivers
dm: gpio: Fix gpio_get_list_count failing with livetree
Change-Id: I391f68fc2c7413372aa66f38805b8dca3cdb80c2
There are a number of platforms that depend on a SATA driver that has
been converted to require AHCI but the platforms themselves are behind
on other migrations that would make it trivial to enable AHCI. Disable
SATA in these cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a callback harts_early_init() to start.S to allow different riscv
hart perform setup code for each hart as early as possible. Since all
the harts enter the callback, they must be able to run the same
setup.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Check that a variable defined in /config/environment is found in the
run-time environment, and that clearing fdt_env_path from within that
node works.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: Conditionalize the test being linked in]
Signed-off-by: Tom Rini <trini@konsulko.com>
Frequency requested by ddrphy_init_set_dfi_clk from fracpll uses MHZ()
macro, which expands the value provided to the Hz range without taking into
account the precise Hz setting. This causes the frequency of 266 MHz not ot
be found in the imx8mm_fracpll_tbl, since it is entered there with a
precise Hz value. This in turn causes the boot hang in SPL, as proper DDR
fracpll frequency cannot be determined.
Correct the value in imx8mm_fracpll_tbl to match the one expanded by
MHZ(266) macro, rounding it down to MHz range only.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Fixes: 825ab6b406 ("driver: ddr: Refine the ddr init driver on imx8m")
Supported peripherals: Ethernet, eMMC, Serial.
U-Boot SPL 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14
+0200)
Normal Boot
Trying to boot from MMC2
U-Boot 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14 +0200)
CPU: Freescale i.MX8MQ rev2.1 at 1000 MHz
Reset cause: POR
Model: Ronetix iMX8M-CM SoM
DRAM: 1 GiB
WDT: Started with servicing (60s timeout)
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@30be0000 (eth0) using random MAC address -
42:0d:e7:78:da:53
eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
u-boot=>
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
instead using ls and awk to determine file size use stat instead.
This fixes an invalid size reporting for user or group names that have
spaces in them.
This adds a dependency on the stat application which is part of
the coreutils package which also includes ls.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Remove the invalid 'regulator-always-on' property to resolve:
starting USB...
Bus usb@2184000: Error enabling VBUS supply (ret=-13)
probe failed, error -13
Bus usb@2184200: USB EHCI 1.00
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Engicam C.TOUCH 2.0 is an EDIMM compliant general purpose Carrier
board.
Genaral features:
- Ethernet 10/100
- Wifi/BT
- USB Type A/OTG
- Audio Out
- CAN
- LVDS panel connector
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.
i.Core MX8M Mini needs to mount on top of this Carrier board for
creating complete i.Core MX8M Mini C.TOUCH 2.0 board.
Linux dts commit details:
commit <a142252061ff> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
C.TOUCH 2.0")
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.
i.Core MX8M Mini needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Mini EDIMM2.2 Starter Kit.
Linux dts commit details:
commit <051c08eea682> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
EDIMM2.2 Starter Kit")
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini
from Engicam.
General features:
- NXP i.MX8M Mini
- Up to 2GB LDDR4
- 8/16GB eMMC
- Gigabit Ethernet
- USB 2.0 Host/OTG
- PCIe Gen2 interface
- I2S
- MIPI DSI to LVDS
- rest of i.MX8M Mini features
i.Core MX8M Mini needs to mount on top of Engicam baseboards
for creating complete platform solutions.
Linux dts commit details:
commit <470d6dad5ddd> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
SoM")
Add support for it.
Signed-off-by: Matteo Lisi <matteo.lisi@engicam.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
/soc@0
aips1
aips2
aips3
clk
iomuxc
osc_24m
are common node enablements across imx8mm platform for dm-spi,
dm-pre-reloc stages.
Move them into common dtsi, imx8mm-u-boot.dtsi
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Teresa Remmet <t.remmet@phytec.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add PHY's reset GPIO, so that U-Boot does a PHY hard reset.
This is needed, since the PHY might become unresponsive if
watchdog reboots the system while a transaction is ongoing.
The reset GPIO is added to the U-Boot specific DT files, since
the kernel does not setup the reserved registers correctly after
resetting the PHY and thus must not reset it.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In CP115, comphy4 can be configured into SFI port1
(in addition to SFI0). This patch adds the option
described above.
In addition, rename all existing SFI/XFI references:
COMPHY_TYPE_SFI --> COMPHY_TYPE_SFI0
No functional change for exsiting configuration.
Change-Id: If9176222e0080424ba67347fe4d320215b1ba0c0
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
According to Design Reference Specification the PHY PLL and Calibration
register from PHY0 are shared for multi-port PHY. PLL control registers
inside other PHY channels are not used.
This commit reworks utmi device tree nodes in a way that common PHY PLL
registers are moved to main utmi node. Accordingly both child nodes
utmi-unit range is reduced and register offsets in utmi_phy.h are updated
to this change.
This fixes issues in scenarios when only utmi port1 was in use, which
resulted with lack of correct pll initialization.
Change-Id: Icc520dfa719f43a09493ab31f671efbe88872097
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Even if comphy types of SATA2/SATA3/SGMII3 and comphy speeds of
1.5G/3G/6.25G were referenced in the driver non configuration (dts)
was using it.
This patch removes unused definitions.
Change-Id: I53ed6f9d3a82b9d18cb4e488bc14d3cf687f9488
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Currently, all comphy definitions are PHY_TYPE_XX and PHY_SPEEED_XX.
Those definition might be confused with MDIO PHY definitions.
This patch does the following changes:
- PHY_TYPE_XX --> COMPHY_TYPE_XX
- PHY_SPEED_XX --> COMPHY_SPEED_XX
This improves readability, no functional change.
Change-Id: I2bd1d9289ebbc5c16fa80f9870f797ea1bcaf5fa
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Because of the incorrectly supported SGMII_2500 mode, this patch
disables eth2 for now until this issue will be fixed in mainline.
Also fix an incorrect comment.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Marek Behun <marek.behun@nic.cz>
This patch adds the base support for the Marvell Octeon TX2 CN9130 CRB.
Not all interfaces are supported fully yet.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the dtsi/dts files needed to support the Marvell
Octeon TX2 CN9130 CRB. This is only the base port with not all
interfaces supported fully.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for SoCs based on AP807 die.
Remove unused include file for Armada-8020 SoC.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Use a single dtsi file for CP110 die instead of master/slave.
Moving to single file will allow miltiple DTSI inclusions with
re-defined CP index and name.
This change will also allow support for SoCs containing more than
two CP110 dies on board.
Move pin control definitions from CP110 DTS to board DTS files
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
With this extended test, we get the following failure :
=> ut dm reset_base
Test: dm_test_reset_base: reset.c
test/dm/reset.c:52, dm_test_reset_base(): reset_method3.id == reset_method3_1.id: Expected 0x14 (20), got 0x2 (2)
Test: dm_test_reset_base: reset.c (flat tree)
test/dm/reset.c:52, dm_test_reset_base(): reset_method3.id == reset_method3_1.id: Expected 0x14 (20), got 0x2 (2)
Failures: 2
A fix is needed in reset_get_by_index_nodev() when introduced in [1].
[1] ea9dc35aab ("reset: Get the RESET by index without device")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
When zImage support was added to SPL, the messages were hidden to reduce
code size. However, the wrong config symbol was used. Since this file is
only built when CONFIG_SPL_FRAMEWORK=y, the messages were always hidden.
Use the correct symbol so the messages are printed in U-Boot proper.
Also use IS_ENABLED to drop the #ifdef.
Fixes: 431889d6ad ("spl: zImage support in Falcon mode")
Signed-off-by: Samuel Holland <samuel@sholland.org>
When flush_cache() is called during boot on our ~7M kernel image, the
hundreds of thousands of WATCHDOG_RESET calls end up adding
significantly to boottime. Flushing a single cache line doesn't take
many microseconds, so doing these calls for every cache line is
complete overkill.
The generic watchdog_reset() provided by wdt-uclass.c actually
contains some rate-limiting logic that should in theory mitigate this,
but alas, that rate-limiting must be disabled on powerpc because of
its get_timer() implementation - get_timer() works just fine until
interrupts are disabled, but it just so happens that the "big"
flush_cache() call happens in the part of bootm where interrupts are
indeed disabled. [1] [2] [3]
I have checked with objdump that the generated code doesn't change
when this option is left at its default value of 0: gcc is smart
enough to see that the ">=" comparison is tautologically true, hence
all assignments to "flushed" are eliminated as dead stores.
On our board, setting the option to something like 65536 ends up
reducing total boottime by about 0.8 seconds.
[1] https://patchwork.ozlabs.org/project/uboot/patch/20200605111657.28773-1-rasmus.villemoes@prevas.dk/
[2] https://lists.denx.de/pipermail/u-boot/2021-April/446906.html
[3] https://lists.denx.de/pipermail/u-boot/2021-April/447280.html
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
CONFIG_5xx hasn't existed since commit 5025897774 (powerpc, 5xx:
remove support for 5xx). Remove this last mention of it.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Having WATCHDOG_RESET() called automatically from the timer interrupt
runs counter to the idea of a watchdog device - if the board runs into
an infinite loops with interrupts still enabled, the watchdog will
never fire.
When using CONFIG_(SPL_)WDT, the watchdog_reset function is a lot more
complicated than just poking a few SOC-specific registers - it
involves accessing all kinds of global data, and if the interrupt
happens at the wrong time (say, in the middle of an WATCHDOG_RESET()
call from ordinary code), that can end up corrupting said global data.
Allow the board to opt out of calling WATCHDOG_RESET() from the timer
interrupt handler by setting CONFIG_SYS_WATCHDOG_FREQ to 0 - as that
setting is currently nonsensical (it would be compile-time
divide-by-zero), it cannot affect any existing boards.
Add documentation for both the existing and extended meaning of
CONFIG_SYS_WATCHDOG_FREQ.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Import updated devicetree files from the Linux v5.12 release.
Besides some node and audio port renames this changes the PHY modes to
either rgmii-id or rgmii-txid. From the board files the Pinephone sees
a lot of updates.
This also adds the long missing USB PHY property for controller 0, which
allows the U-Boot PHY driver to eventually use port 0 in host mode
(pending another U-Boot patch).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Update R40 .dts{,i} and dt-binding headers to current version from kernel.
Files taken from Linux 5.12-rc1 release
(commit fe07bfda2fb9cdef8a4d4008a409bb02f35f1bd8)
Signed-off-by: Ivan Uvarov <i.uvarov@cognitivepilot.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch adds support for the following I2C devices connected to
I2C bus 0 on the Octeon EBB7304:
- Dallas DS1337 RTC
- TLV EEPROM
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
We already have a clock driver for MIPS Octeon. This patch changes the
Octeon DT nodes to supply the clock property via the clock driver
instead of using an hard-coded value, which is not correct in all cases.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add the AHCI compatible SATA DT node to the Octeon CN73xx dtsi file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
For easy AHCI/ SATA integration, this patch adds board_ahci_enable()
for the MVEBU AHCI driver, which will be used by this platform. This
platform specific "enable" function will setup the proper endian
swapping in the AHCI controller so that it can be used by the common
AHCI code.
Additionally the endian swizzle entry for AHCI in
octeon_should_swizzle_table[] is removed, as this enabled the original
lowlevel code function, e.g. octeon_configure_qlm(), for the QLM setup
to work correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds the necessary platform infrastructure code, so that the
MIPS Octeon drivers "serial_octeon_pcie_console" & "serial_bootcmd" can
be used. This is e.g. the bootmem initialization in a compatible way to
the Marvell 2013 U-Boot, so that the exisiting PC remote tools like
"oct-remote-console" & "oct-remote-load" can be used. This is be done in
the newly introduced arch_misc_init(), which calls the necessary init
functions when enabled.
These patches are in preparation for the MIPS Octeon NIC23 board
support, which is a desktop PCIe target board enabling these features.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
As DEBUG is no Kconfig symbol, we can't use the IS_ENABLED() macros.
This patch switches to the unfortunately necessary #ifdef usage again
to make it work correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
While porting from the Marvell source, I introduced a bug by misplacing
the parenthesis. This patch fixes this issue.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the newly added C files to the Makefile to enable
compilation. This is done in a separate step, to not introduce build
breakage while adding the single files with potentially missing
externals.
Signed-off-by: Stefan Roese <sr@denx.de>
Import octeon_qlm.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import octeon_fdt.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-qlm.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pcie.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-util.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-jtag.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-fdt.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-cfg.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
To match all other cvmx-* header, this patch moves the already existing
cvmx-lmcx-defs.h header one directory up.
Signed-off-by: Stefan Roese <sr@denx.de>
With the newly added headers and their restructuring (which macro is
defined where), some changes in the already existing Octeon files are
necessary. This patch makes the necessary changes.
Signed-off-by: Stefan Roese <sr@denx.de>
Import misc remaining header files from 2013 U-Boot. These will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Import cvmx-sso-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-sriox-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-sriomaintx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-smix-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-sli-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-sata-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-rst-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pow-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pko-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pki-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pip-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pepx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pemx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pcsx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pciercx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pcieepx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-npi-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-mio-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-l2c-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-ipd-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-gserx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-gmxx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-fpa-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-dtx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-dpi-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-dbg-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-ciu-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-bgxx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-asxx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-agl-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import misc cvmx-helper header files from 2013 U-Boot. They will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This will be used by the upcoming Serdes and driver code ported from
the original 2013 U-Boot code to mainline.
Signed-off-by: Stefan Roese <sr@denx.de>
Add the MMC DT node to the Octeon EBB7304 DT file including the
regulator node for the MMC power supply.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add the MMC DT node to the Octeon CN73xx dtsi file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Until now, the Octeontx MMC driver did only support the ARM Octeon
TX/Tx2 platforms. This patch adds support for the MIPS Octeon platform
to this driver. Here a short summary of the changes:
- Enable driver compilation for MIPS Octeon, including the MMC related
header file
- Reorder header inclusion
- Switch to using the clk framework to get the input clock
- Remove some functions for MIPS Octeon, as some registers don't
exist here
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The MT7688KN is a multi-chip package with 8MiB DDR1 KGD. So the DDR type
from bootstrap register must be ignored, and always be assumed as DDR1.
This patch fixes the displayed DDR type of mt7628.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The MT7688KN is a multi-chip package with 8MiB DDR1 KGD. So the DDR type
from bootstrap register must be ignored, and always be assumed as DDR1.
This patch fixes an issue that mt7628_ddr_pad_ldo_config() may be passed
with a wrong ddr_type in MT7688KN.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Make sure to reset the switch core at probe time.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Import the i.MX6SX based UDOO Neo dts files from Linux 5.12-rc1
and sync the i.MX6SX pinfunc.h
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add support for stack protector for UBOOT, SPL, and TPL
as well as new pytest for stackprotector
Signed-off-by: Joel Peshkin <joel.peshkin@broadcom.com>
Adjust UEFI build flags.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The current usage of the variable CFLAGS_NON_EFI on the x86 architecture
deviates from other architectures.
Variable CFLAGS_NON_EFI is the list of compiler flags to be removed when
building UEFI applications. It is not a list of flags to be added anywhere.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
So far U-Boot was hard coding a (surely sufficient) memory size of 512
MB, even though all machines out there have at least 4GB of DRAM.
Since U-Boot uses its memory knowledge to populate the EFI memory map,
we are missing out here, at best losing everything beyond 4GB on Midway
boxes (which typically come with 8GB of DRAM).
Since the management processor populated the DT memory node already with
the detected DRAM size and configuration, we use that to populate
U-Boot's memory bank information, which is the base for the UEFI memory
map.
This finally allows us to get rid of the NR_DRAM_BANKS=0 hack, that we
had in place to avoid U-Boot messing up the DT memory node before
loading the kernel.
Also, to cover the whole of memory, we need to enable PHYS_64BIT.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
To squash that nasty warning message and make better use of the newly
gained OF_CONTROL feature, let's convert the calxedagmac driver to the
"new" driver model.
The conversion is pretty straight forward, mostly just adjusting the
use of the involved data structures.
The only actual change is the required split of the receive routine into
a receive and free_pkt part.
Also this allows us to get rid of the hardcoded platform information and
explicit init calls.
This also uses the opportunity to wrap the code decoding the MMIO
register base address, to make it safe for using PHYS_64BIT later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
All Calxeda machines are actually a poster book example of device tree
usage: the DT is loaded from flash by the management processor into
DRAM, the memory node is populated with the detected DRAM size and this
DT is then handed over to the kernel.
So it's a shame that U-Boot didn't participate in this chain, but
fortunately this is easy to fix:
Define CONFIG_OF_CONTROL and CONFIG_OF_BOARD, and provide a trivial
function to tell U-Boot about the (fixed) location of the DTB in DRAM.
Then enable DM_SERIAL, to let the PL011 driver pick up the UART platform
data from the DT. Also define AHCI, to bring this driver into the driver
model world as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
use 'select' to enable IRQ as it does not have architecture
specific dependency.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The GICv3 RM requires "The first 1KB of memory for the LPI Pending tables
must contain only zeros on initial allocation, and this must be visible
to the Redistributors, or else the effect is UNPREDICTABLE".
And as the following statement, we here clear the whole Pending tables
instead of the first 1KB.
"An LPI Pending table that contains only zeros, including in the first 1KB,
indicates that there are no pending LPIs.
The first 1KB of the LPI Pending table is IMPLEMENTATION DEFINED. However,
if the first 1KB of the LPI Pending table and the rest of the table contain
only zeros, this must indicate that there are no pending LPIs."
And there isn't any pending LPI under U-Boot, so it's unnecessary to
load the contents of the Pending table during the enablement, then set
the GICR_PENDBASER.PTZ flag.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # NXP LS1028A
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable PCIe by default in u-boot, this should eventually be made dynamic
in the runtime board config depending on the MCU configuration.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The sync of the device tree and dt-bindings from Linux v5.6-rc2
11a48a5a18c6 ("Linux 5.6-rc2") causes Ethernet to break on some
ODROID-C2. The PHY seems to need proper reset timing to be functional
in U-Boot and Linux afterwards. Readd the old PHY reset bindings for
dwmac until we support the new bindings in the PHY node.
Fixes: dd5f2351e9 ("arm64: dts: meson: sync dt and bindings from v5.6-rc2")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmB9NEccHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyBp1CACFd9d7fokb59aFGeta
RaVD4Ni/5WUMT2ulUWYVn2KPmDLouXKZfvQZxakTJJkLCKfIKpQJ6pw82SUPqNc1
xhFS+YOxuDwhbB6ksApq7eUOga9T/K3S/8T4gPWkAOsAwlJGeF5AE1uxWFLbiNzt
eC2kMtRnwHmRq+fOuLsz1EHHKGcp+mtOnXEy2tv23xcGMqeCPzGsK7DWp1dw66gc
sqj7RdkfP/Ies557Ai/NjfdiOx1ThuVmNz/CgJgVf2/vHiQNgi4jHHDYQG55nGzJ
ExLtlom0L3ttko/hlznANFfPD6PBeF03T1cOT8jgx9/RFIF6dqDoA1YOa2dajhuW
xq5k
=MPfk
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.07-b' of https://source.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.07 cycle:
This small feature set include support for 5th PIO bank on pio4 pinctrl
driver and a fix for the SPL on sama5d3.
This reverts commit 38d6b7ebda.
struct global_data contains a pointer to the bd_info structure. This
pointer was populated spl_set_bd() to a pre-allocated bd_info in the
".data" section. The referenced commit replaced this mechanism to one
that uses malloc(). That new mechanism is only used if SPL_ALLOC_BD=y.
which very few boards do.
The result is that (struct global_data)->bd is NULL in SPL on most
platforms. This breaks falcon mode, since arch_fixup_fdt() tries to
access (struct global_data)->bd and set the "/memory" node in the
devicetree. The result is that the "/memory" node contains garbage
values, causing linux to panic() as it sets up the page table.
Instead of trying to fix the mess, potentially causing other issues,
revert to the code that worked, while this change is reworked.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
in the early SPL boot stage whenever there is a call to udelay,
dm_timer_init fails to find the pit timer whenever it traverses
the device tree, if this property is not present
Signed-off-by: Manuel Reis <mluis.reis@gmail.com>
CC: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
This is a patchset which makes away with the .bind() controller indexing
workaround which was broken since before v2021.04, and then adds PHY
support and MX8M support on top of that. Better add it into the release
early to get as much testing as possible done, because this really does
a lot of changes to the ehci-mx6 driver.
Add power domain nodes to DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Add power domain nodes to DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
The fsl,usbphy DT property is deprecated, replace it with phys DT
property and specify #phy-cells, so that the generic PHY framework
can parse the PHY bindings without any extra hacking.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
The fsl,usbphy DT property is deprecated, replace it with phys DT
property and specify #phy-cells, so that the generic PHY framework
can parse the PHY bindings without any extra hacking.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
The standard compatible string is "usb-nop-xceiv", use it.
Note that keystone-k2g.dtsi already uses the aforementioned
compat string, so this patch can only remove the override.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
According to latest errata of J721e [1], HS400 mode is not supported
in MMCSD0 subsystem (i2024) and SDR104 mode is not supported in MMCSD1/2
subsystems (i2090). Therefore, replace mmc-hs400-1_8v with mmc-hs200-1_8v
in MMCSD0 subsystem and add a sdhci mask to disable SDR104 speed mode.
Also, update the itap delay values for all the MMCSD subsystems according
the latest J721e data sheet[2]
[1] - https://www.ti.com/lit/er/sprz455/sprz455.pdf
[2] - https://www.ti.com/lit/ds/symlink/tda4vm.pdf
Fixes: 70e167495a ("arm: dts: k3-j721e: Sync Linux v5.11-rc6 dts into U-Boot")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
This adds support for devices with R40 dual rank DRAM, and asymmetric
A64 DRAM devices like the Pinephone/3GB.
Also we enable automatic gzipped kernel support, and allow scripted
DT overlay support. The rest of the patches are cleanups, but also
some sunxi-specific preparatory patches for USB3.0 and improved HDMI
support. The bulk of those changes will go through other trees, though.
Build-tested for all 156 sunxi boards, and boot tested on a A64, A20, R40,
H5, H6 and H616 board. USB, SD card, eMMC, HDMI and Ethernet all work
there (where applicable), with the exception of Ethernet on the H5. Since
this is already broken in v2021.04, I will send a separate fix.
Currently sunxi Makefile manually specifies full path to dw-hdmi common
code. However, that is not needed because it can be selected in Kconfig
instead.
Select proper symbol in Kconfig and drop path from Makefile.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The FIT description has access to the configuration variables. Use the
appropriate variable instead of hardcoding the address.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
binman can fill in the default FIT configuration index as selected by
the "default-dt" argument, which is set to CONFIG_DEFAULT_DEVICE_TREE.
Let's respect the user's configuration by taking advantage of this
feature, instead of always defaulting to the first device tree in
CONFIG_OF_LIST.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Previously we do not have proper dual rank memory detection on R40
(because we omitted PIR_QSGATE, which does not work on R40 with our
configuration), and dual rank memory is just simply disabled as early
R40 boards available (Banana Pi M2 Ultra and Berry) have single rank
memory.
As a board with dual rank memory (Forlinx OKA40i-C) is now known to us,
we need to have a way to do memory rank detection to support that board.
Add some routine to detect memory rank by trying to access the memory
in rank 1 and check for error status of the memory controller, and then
enable dual rank memory on R40.
Similar routine can be used to detect half DQ width (which is also
detected by PIR_QSGATE on other SoCs), but it's left unimplemented
because there's no known R40 board with half DQ width now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[Andre: Move R40 detect code call into sunxi_dram_init()]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Previously we have known that R40 has a configuration register for its
rank 1, which allows different configuration than rank 0. Reverse
engineering of newest libdram of A64 from Allwinner shows that A64 has
this register too. It's bit 0 (which enables dual rank in rank 0
configuration register) means a dedicated rank size setup is used for
rank 1.
Now, Pine64 scheduled to use a 3GiB LPDDR3 DRAM chip (which has 2GiB
rank 0 and 1GiB rank 1) on PinePhone, that makes asymmetric dual rank
DRAM support necessary.
Add this support. The code could support both A64 and R40, but because
dual rank detection is broken on R40 now, we cannot really use it on R40
currently.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
update ls1028aqds networking protocol, config in ls1021atwr, env in ls1012a
Add seli3 board support, booke watchdog, update eTSEC support in ppc-qemu
Add DM_SERIAL and lpuart in sl28, add DM_ETH support for some of powerpc platforms
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
- Minor fix to Apollo Lake devicetree bindings for FSP
- Refactor Designware PCIe drivers to core and SoC parts
- Add Amlogic Meson Designware PCIe controller driver
Add the FMan v3 nodes for the T1042D4RDB. The nodes are copied over with
little modification from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA 1 FMan v3 device tree nodes for the T1042 SoC.
The device tree nodes are copied over with little modification
from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When two FMan's are present on a board, the MDIO nodes are found at the
same offsets inside each FMan. This causes "non unique device name"
errors when registering the MDIO nodes under the second FMan. Fix this
by updating the offsets of the MDIO nodes to include the parent FMan's
offset.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the FMan v3 nodes for the T4240RDB. The nodes are copied over with
little modification from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA 1 FMan v3 device tree nodes for the T4240 SoC.
The device tree nodes are copied over with little modification
from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the FMan v3 nodes for the T2080RDB. The nodes are copied over with
little modification from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA 1 FMan v3 device tree nodes for the T2080 SoC.
The device tree nodes are copied over with little modification from
the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Sometimes it is desireable to have the console output on the first
serial line. Introduce a configuration option for it (in the board
scope).
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
With all preparations in place, switch over to DM_SERIAL.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move the CONFIG_DM_* from the defconfig to the TARGET_SL28 config.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SERIAL needs both the device tree as well as an early heap. Thus, we
have to call spl_early_init() to initialize the memory allocator and the
setup the device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
To use the debug UART we have to call debug_uart_init() in the SPL. Do
so as soon as possible.
As an example, here is how you can use it on a LS1028A SoC:
CONFIG_DEBUG_UART=y
CONFIG_DEBUG_UART_BASE=0x21c0500
CONFIG_DEBUG_UART_CLOCK=200000000
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This adds a test case to test the new ofnode_phy_is_fixed_link() API.
Both the new and old DT bindings are covered.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The DSA sandbox driver is used for unit testing the DSA class code.
It implements a simple 2 port switch plus 1 CPU port, and uses a
very simple tag to identify the ports.
The DSA sandbox device is connected via CPU port to a regular Ethernet
sandbox device, called 'dsa-test-eth, managed by the existing eth
sandbox driver. The 'dsa-test-eth' is not intended for testing the
eth class code however, but it is used to emulate traffic through the
'lan0' and 'lan1' front pannel switch ports. To achieve this the dsa
sandbox driver registers a tx handler for the 'dsa-test-eth' device.
The switch ports, labeled as 'lan0' and 'lan1', are also registered
as eth devices by the dsa class code this time. So pinging through
these switch ports is as easy as:
=> setenv ethact lan0
=> ping 1.2.3.5
Unit tests for the dsa class code were also added. The 'dsa_probe'
test exercises most API functions from dsa.h. The 'dsa' unit test
simply exercises ARP/ICMP traffic through the two switch ports,
including tag injection and extraction, with the help of the dsa
sandbox driver.
I took care to minimize the impact on the existing eth unit tests,
though some adjustments needed to be made with the addition of
extra eth interfaces used by the dsa unit tests. The additional eth
interfaces also require MAC addresses, these have been added to the
sandbox default environment.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-Id: <20210216224804.3355044-5-olteanv@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The SELI8 design is a new tdm service unit card for Hitachi-Powergrids
XMC and FOX product lines.
It is based on NXP LS1021 SoC and it provides following interfaces:
- IFC interface for NOR, NAND and external FPGA's
- 1 x RGMII ETH for debug purposes
- 2 x SGMII ETH for management communication via back-plane
- 1 x uQE HDLC for management communication via back-plane
- 1 x I2C for peripheral devices
- 1 x SPI for peripheral devices
- 1 x UART for debug logging
It is foreseen that the design will be later re-used for another XMC and
FOX service cards with similar SoC requirements.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Matteo Ghidoni <matteo.ghidoni@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Includes DT definition for the following serdes protocols using various
PHY cards: 85xx, 13xx, 65xx, 9999, 7777.
Note that the default device tree for QDS now uses 85xx.
Enabling any of the others requires patching the fsl-ls1028a-qds.dtsi
file (the includes at the bottom of the file).
The phy-handle is specified as a path rather than a label because it is
possible to use the #include multiple times (meaning that more than one
PHY riser card of one type is inserted), and therefore, there would be
duplicate labels with the same name.
LBRW means that the board needs lane B rework before using this dtsi.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix copy/paste errors in the descriptions of mtrr_close () and mtrr_set().
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Several architectures had a default board_fit_config_name_match already;
this provides a generic weak version. We default to rejecting all configs.
This will use the FIT's default config, instead of the first config. This
may result in boot failures if there are multiple configurations and the
first config is *not* the default.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
We move qfw into its own uclass and split the PIO functions into a
specific driver for that uclass. The PIO driver is selected in the
qemu-x86 board config (this covers x86 and x86_64).
include/qfw.h is cleaned up and documentation added.
Signed-off-by: Asherah Connor <ashe@kivikakk.ee>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Fix inline comments and empty line in scmi driver and test files.
Remove test on IS_ENABLED(CONFIG_*_SCMI) in test/dm/scmi.c since these
configuration are expected enabled when CONFIG_FIRMWARE_SCMI is enabled
in sandbox configuration.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Implement sandbox regulator devices for SCMI voltage domains
and test them in DM scmi tests.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
It's an old bringup board with out upstream Linux or L4T support
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
On ARMv8 systems
load mmc 0:1 $loadaddr vmlinuz-5.10.0-3-arm64
booti
leads to a hanging system requiring to physically reset the system:
FDT and ATAGS support not compiled in - hanging
### ERROR ### Please RESET the board ###
For systems where physical access is difficult hanging is a poor choice.
It is preferable to reset the system when U-Boot reaches a state that is
not recoverable.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The test adds two pinmux nodes to the device tree, one to test when a
register changes only one pin's mux (pinctrl-single,pins), and the other
to test when more than one pin's mux is changed (pinctrl-single,bits).
This required replacing the controller's register access functions when
the driver is used on sandbox.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them. As the P5020 is the last ARCH_P5020 platform, remove that
support as well.
Cc: Andy Fleming <afleming@gmail.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
With the last of the ARCH_P1022 platforms removed, finish removing the
rest of the platform support.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them.
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC, along with other
DM conversions, by the deadline. Remove them.
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC, along with other
DM conversions, by the deadline. Remove them.
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>