Build warning was added by:
"fdt: Add warning about CONFIG_OF_EMBED"
(sha1: 841d5fbae4)
Zynq mini configurations are not moved yet and it is questionable if
make sense to move them too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Build warning was added by:
"fdt: Add warning about CONFIG_OF_EMBED"
(sha1: 841d5fbae4)
ZynqMP mini configurations are not moved yet and it is questionable if
make sense to move them too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable ISSI flash for platforms. Xilinx reference boards are also used
internally with different flash part to increase coverage that's why
enable also ISSI parts for all these boards even if that board is
released only with one part.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch enable net configs for zc1275 board.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add board support and configuration for Jaguar2 SoC family.
The detection of the board type is based on the phy ids.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add board support, configuration and DTS for Servalt SoC
family. Currently there is one board in this family.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Now that network support is added for the ocelot platform, let's add it
in the default configuration.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
- Sync Armada-38x dts with Linux 4.20 from Chris
- Misc changes and enhancements to Turris Mox (v4) from Marek
- Reserve PSCI area for Armada 8k from Heinrich
- New Allied Telesis x530 board (Armada-385) from Chris
- Misc minor changes (defconfig etc)
This is a range of stackable network switches. The SoC is Armada-385 and
there are a number of variants with differing network port
configurations. The DP variants are intended for a harsher operating
environment so they use a different i2c mux and fit industrial-temp
parts.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
An NVME drive may be installed on the MACCHIATObin board using the PCIe
slot or on the Clearfog Pro using mini a PCI-e slot. With the configuration
change it becomes usable.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add gpio command to defconfig - this can be used to detect whether the
button is pressed or light LEDs.
Add DS1307 RTC driver and the date command.
Add CONFIG_WATCHDOG, so that U-Boot calls watchdog_reset.
Add CONFIG_MISC_INIT_R so that ethernet addresses are read from OTP
before network controller is initialized.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The bounce buffer is used by a few drivers (most of the MMC drivers)
to overcome limitations in their respective DMA implementation.
This moves the configuration to Kconfig and makes it user-selectable
(even though it will be a required feature to make those drivers
work): the expected usage is for drivers depending on this to 'select'
it unconditionally from their respective Kconfig (see follow-up
patches).
This commit includes a full migration using moveconfig.py to ensure
that each commit compiles. To ensure bisectability we update
dependencies of various drivers to now select BOUNCE_BUFFER when needed.
[trini: Squash all patches to ensure bisectability]
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br> [dw_mmc portion]
Reviewed-by: Fabio Estevam <festevam@gmail.com> [mxsmmc portion]
Reviewed-by: Simon Glass <sjg@chromium.org> [tegra portion]
The am335x_evm_defconfig supports all am335x_boneblack variants. Remove
the redundant am335x_boneblack_defconfig.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On this board SPI is only used to configure the SoC driving the LC TFT
display which is not used in U-Boot. Hence remove SPI support.
Signed-off-by: Felix Brack <fb@ltec.ch>
Onc of key blocker for using USB Generic host controller
drivers in Allwinner are CLK and RESET drivers, now these
available for USB usage.
So switch sunxi USB use EHCI and OHCI Generic controllers.
Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD
where it already have USB_EHCI_HCD
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Emlid Neutis N5 is a SoM based on Allwinner H5, has a WiFi & BT
module, DDR3 RAM and eMMC.
- add neutis-devboard target to dtb makefile
- add dtsi file for Neutis N5 needs
- add config file for Neutis N5 Dev board
Signed-off-by: Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: update proper commit head]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
am43xx_evm_ethboot_defconfig is not being actively used and has not been
moved to DM or DT. Also, ethboot cannot be tested on AM43xx EVM as such
due EVM limitations. Therefore delete it.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These defconfigs don't seem be actively used any more, and have not been
moved to adapt DM or DT. Therefore delete them.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
bananapi r2 can be booted from sd-card and emmc
saving the environment have to choose the storage
from which the device has booted
also the offset is set to 1MB to make sure env is written
to block "user data area" between uboot and first partition
https://www.fw-web.de/dokuwiki/lib/exe/fetch.php?cache=&media=bpi-r2:boot-structure.png
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
update TFABOOT defconfig for SD boot on below NXP chasis2
and chasis3 platforms:
ls1043a, ls1046a, ls1088a and ls2088a.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls2088aqds_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls2088ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- remove EL3 specific erratas for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1088aqds_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- MC address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- ifc chip select changes for TFABOOT
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1088ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- MC address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- ifc chip select changes for TFABOOT
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
With the new SPI NOR framework in v4.19, we need to adapt the MTD parts
so that the kernel cmdline parameter "mtdparts=" uses the correct naming
for the devices.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Fix the Kconfig warning to not use CONFIG_OF_EMBED in defconfigs.
Based on https://patchwork.ozlabs.org/patch/1019791/
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add board support and configuration for Jaguar2 SOC family.
The detection of the board type in this family is based on the phy ids.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Thes patch change the luton base device tree to use the newly added
SPI bitbang driver.
It also updates the "mscc_luton_defconfig" to use the new driver.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
There is no real difference between the generic variant and
the custom variant except that the generic variant is more
optimised. This also saves 24 Bytes in the SPL binary.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@collabora.com>
This enables the use of the MSCC serial GPIO driver to control the
LEDs on the MSCC VCoreIII 'ocelot' pcb123 and pcb120.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
This enables the use of the MSCC serial GPIO driver to control the
LEDs on the MSCC VCoreIII 'luton' SoC.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
As we are moving to multi-dtb and board detection, remove static board
config options, and introduce board probing instead.
Luton: This add single-binary support for the two MSCC luton-based
reference boards - pcb090 and pcb091. The SoC chip ID is used to
determine the board type.
Ocelot: This add single-binary support for the two MSCC ocelot-based
reference boards - pcb120 and pcb123. The PHY ids on specific ports
are used to determine the board type.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Building with CONFIG_OF_EMBED generates build warnings, as it should
only be used for debugging purposes.
Remove CONFIG_OF_EMBED from all stm32 config files which are using
this flag.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This adds device tree for OMAP3 IGEP based boards and the DM_MMC driver.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The USB support for this board was never really tested, in fact, the
presence of these options are more a copy & paste error from the
Beagleboard than a feature that really was used. As doesn't work, remove
for now. If someone at some point want to add this support he'll need to
migrate the board to use CONFIG_DM_USB instead.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
The IGEP0032 board was never officially pushed upstream and actually I
don't have access to this hardware, unless someone with the hardware
wants to start working on this doesn't makes sense have this defconfig
here. So remove it.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Convert HiSilicon HI6220 MMC driver based on DWMMC IP to driver
model.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Enable this on poplar]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch replace OF_EMBED with OF_SEPARATE of defconfig files of
MediaTek boards because now OF_EMBED is only used for debugging purpose.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable ethernet related configs to mt7629_rfb_defconfig.
Add default IP addresses.
Enable noncached memory region required by ethernet driver.
Signed-off-by: Mark Lee <Mark-MC.Lee@mediatek.com>
Enable ethernet related configs to mt7623n_bpir2_defconfig.
Add default IP addresses.
Enable noncached memory region required by ethernet driver.
Signed-off-by: Mark Lee <Mark-MC.Lee@mediatek.com>
Add a test for the bootcount uclass, which uses the RTC bootcount backend
(i.e. drivers/bootcount/rtc.c is implictly also tested).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Chris Spencer reports that when enabling ext4 read support without
also enabling write support the following error is seen:
fs/fs.c:198:12: error: 'ext4_write_file' undeclared here (not in a
function); did you mean 'ext4_read_file'?
.write = ext4_write_file,
^~~~~~~~~~~~~~~
Fix this problem by moving these options to Kconfig.
Reported-by: Chris Spencer <spencercw@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
There is no need to compile and include this code if it is not used.
CONFIG_USB_GADGET can be used for the purpose.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The current defconfig build generates a u-boot.imx file that is too large
for the available space on a eMMC/SD card. Installing this file overwrites
the u-boot environment. So disable the unused FIT support to reduce the
size of the u-boot binary.
Signed-off-by: Soeren Moch <smoch@web.de>
Safe some space by not selecting CMD_NFS and CMD_LOADS/B.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This patch enables the full pinctrl driver in the defconfig
for the RK3399-Q7.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch enables the PWM regulator driver in the defconfig
for the RK3399-Q7.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable driver model for USB, MMC and REGULATOR drivers.
Set run-time configuration via Device Tree.
Signed-off-by: Yaniv Levinsky <yaniv.levinsky@compulab.co.il>
CONFIG_CMD_BOOTEFI is enabled by Kconfig default, but rarely
used on this board/platform.
So let's disable it for the boards default config.
This also saves around 16 KiB in the final u-boot.sb.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
While migrating individual status led usages to Kconfig stuff,
a (random) value was introduced for this board which does not
work but produces the following error message during boot:
__led_init: failed requesting GPIO59!
Since Kconfig does not seem to accept a define as this point,
but the mxs gpio driver requires not only a simple integer value,
we need to use the plain value of MX23_PAD_SSP1_DETECT__GPIO_2_1.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Fixes: 2d8d190c83 ("status_led: Kconfig migration")
Use defconfig instead of header file for CONFIG_CMD_PCI.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some users might need additional setups before booting the kernel.
If there is found a file 'boot.scr', run it before invoking the
distro boot command.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Some users might want to modify 'bootcmd' at compile-time by editing
include/configs/uniphier.h, but overwriting it at run-time makes it
impossible.
Instead, set 'bootdev' at run-time, which contains the boot device the
system is booting from, then indirectly reference it from 'bootcmd'.
It is up to users whether to override 'bootcmd'.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
As an example of how to enable TrueType fonts, move chromebook_jerry over
to use these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
db-88f6820-amc uses CONFIG_DM_USB and CONFIG_USB_STORAGE already so
define CONFIG_BLK to prepare it for full conversion to DM.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for the Creator CI20 platform based on the JZ4780 SoC.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Adding the support for the Luton boards PCB91 which share common code with
the Ocelots boards, including board code, device tree and configuration.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Building with CONFIG_OF_EMBED generates build warnings, as it should
only be used for debugging purposes. So let's move all MT7688 targets to
CONFIG_OF_SEPARATE instead with this patch.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Remove cpu name from the defconfig naming.
Because other cpus maybe run on AE350 platform.
So only use platfrom name in defconfig naming
will be better.
Also sync MAINTAINERS:
Rename
a25-ae350_32_defconfig as ae350_rv32_defconfig
ax25-ae350_64_defconfig as ae350_rv64_defconfig
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use standard configuration logic to define EEPROM constants.
Names are based on VPD_EEPROM_ prefix because EEPROM_ is already
used by i2c_eeprom driver.
Signed-off-by: Denis Zalevskiy <denis.zalevskiy@ge.com>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
Add the initial support for Elgin R1 board, which is based on the
RV1108 SoC and has the following features currently supported in
U-Boot:
- UART
- eMMC
- USB
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The motivation for this is to allow distributions to distribute all
possible tools in a generic way, avoiding the need of specific tools
building for each machine.
Especially on OpenEmbedded / Yocto Project ecosystem, it is very
common each BSP to end providing their specific tools when they need
to generate images for some SoC (e.g MX23 / MX28 in meta-freescale
case).
Using this, we can package the tools doing:
$: make tools-only_defconfig
$: make tools-only
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
[trini: Add MAINTAINERS entry for myself, add to .travis.yml, make
U-Boot itself buildable to not trip up other frameworks]
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable DM_USB and DM_USB_GADGET for this platform. Also enable RNDIS boot
support (SPL load u-boot over USB RNDIS).
This is an example of how to use DM_USB on a am335x-based board.
A subsequent series will take this a step further and modify more
defconfigs.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The AM43xx SOCs have the ability to download the SPl through USB (RNDIS).
Adding support for RNDIS in SPL allows to also download u-boot through USB.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The K2G evm uses the generic DWC3 driver. DFU can thus be enabled.
Enabling DFU for easier firmware update.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The keystone platforms can use the generic DC3 driver. Removing the
keystone-spcecific xchi driver and add the configuration options to enable
the generic DWC3 driver on all K2 platforms.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update snow's device tree and config to use driver model for sound. Also
update the others as best we can.
Spring does not appear to have audio support in the kernel. The smdk5250
and smdk5420 boards use a wolfson codec which I cannot test with. So the
only boards that is tested and known to work are snow, pit and pi.
Signed-off-by: Simon Glass <sjg@chromium.org>
The existing config is setup as a gadget but it doesn't use
DM_USB. This patch converts all boards to DM_USB, but as host.
As host, it is able to mount USB drives and browse them.
Signed-off-by: Adam Ford <aford173@gmail.com>
There is no need for an embedded device tree for this board so let the
build process generate a separate u-boot.dtb file instead.
Signed-off-by: Felix Brack <fb@ltec.ch>
Building U-Boot with CONFIG_PCI and CONFIG_DM_PCI enabled, but
CONFIG_SPL_PCI_SUPPORT disabled, results in following linker
error:
lib/built-in.o: In function `fdtdec_get_pci_bar32':
lib/fdtdec.c:305: undefined reference to `dm_pci_read_bar32'
fdtdec.c:305:(.text.fdtdec_get_pci_bar32+0x24): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `dm_pci_read_bar32'
This is because reference to dm_pci_read_bar32() remains in lib/fdtdec.c
while SPL build does not descend into drivers/pci directory in
drivers/Makefile if CONFIG_SPL_PCI_SUPPORT is not enabled.
Fix this by applying appropriate #define guards in lib/fdtdec.c.
It looks like ns16550.c has the same problem, so fixed that too.
To simplify this, CONFIG_SPL_PCI_SUPPORT is renamed to CONFIG_SPL_PCI
(enables use of CONFIG_IS_ENABLED() macro).
Suggested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The function part_init() will only be built when we have both
CONFIG_PARTITIONS and CONFIG_HAVE_BLOCK_DEVICE set. Protect the call to
this function with both of these tests now.
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Vanessa Maegima <vanessa.maegima@nxp.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently on qemu-arm platforms environment is kept in RAM. Instead
use pflash device 1 to provide persistent environment support across
device reset.
Also (optionally) provide support for persistent environment across
qemu machine OFF/ON using following instructions:
- Create envstore.img using qemu-img:
qemu-img create -f raw envstore.img 64M
- Add a pflash drive parameter to the command line:
-drive if=pflash,format=raw,index=1,file=envstore.img
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Add support for lx2160a SoC
-----BEGIN PGP SIGNATURE-----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=aT7d
-----END PGP SIGNATURE-----
Merge tag 'fsl-qoriq-for-v2019.01-rc2' of git://git.denx.de/u-boot-fsl-qoriq
Add TFA boot flow for some Layerscape platforms
Add support for lx2160a SoC
[trini: Add a bunch of missing MAINTAINERS entries]
Signed-off-by: Tom Rini <trini@konsulko.com>
- init DRAM for RK322x in SPL
- add FAN53555 PMIC/regulator driver
- update MicroCrystal RV3029 driver to Kconfig and sync from Linux
- add bootcount uclass and first DM-driver for bootcount
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcDiw9AAoJECaAFcEOcohNEa8H/RBWLbVQjHPXf6EjchXgVcSs
Gc+g2QmKZbN21XebfzBpCuZj62NROTWUcrPtor17yEBiMM1xPfe1vC7qtbkR6USj
VTt1JHeyGx3XafkkUpeps382YPfuaNqtabjwZaXlmeE4/VLbXQPE7x4tC4fdWus4
9K3OGQgRNFirn+RIZ7dQWtCby82PEC3cHkPc/n82cVHofcDsgKYK9mPpfcCn/gWF
A4Fa9cx4pjeaMrBHKjcByCiFmwYBPc97Hqzz64oHOdQP0g3h04ko+2w5DdwdeHVV
jKNcvkHESF4m1RGjrTbLEhy1f5UuOfcA1ise/cDX4pjXlBdwxHmvqT5vsE0MQzI=
=5sHL
-----END PGP SIGNATURE-----
Merge tag 'for-master-20181210' of git://git.denx.de/u-boot-rockchip
Improvements:
- init DRAM for RK322x in SPL
- add FAN53555 PMIC/regulator driver
- update MicroCrystal RV3029 driver to Kconfig and sync from Linux
- add bootcount uclass and first DM-driver for bootcount
With a driver for the FAN53555 regulator family available, let's
enable it for the RK3399-Q7 (which has two of these devices
on-module).
We enable this for the full U-Boot stage only, as these regulators
provide a suitable default voltage and supply non-critical (i.e.
for booting up) power rails only.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The DRA7 platforms requires that the dtb used in the SPL really matches the
platform to have the best MMC performances.
To detect the board type/version an I2C EEPROM is read. This requires that
DM is initialized before the detection. As a consequence we must reset the
DM after the board detection is a new dtb would better match the platform.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This is required to take advantage of MULTI_DTB_FIT before relocation.
If it is too low, DM will be initialized only after relocation has
taken place. That is too late for the DRA7 because I2C DM is used before
the relocation to setup the voltages required, among other things, to
properly initialize the DRAM.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Those platforms need CONFIG_SPL_DM_SEQ_ALIAS because they enable both
DM_I2C and SPL_DM. Without CONFIG_SPL_DM_SEQ_ALIAS, it is not possible to
get the I2C bus with i2c_get_chip_for_busnum().
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Felix Brack <fb@ltec.ch>
Tested-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Enable SPI flash support under U-Boot and SPL. The ENV size and offset,
ported from U-Boot 2013.01 Marvell version: 2015_T1.0p16
To create U-Boot image for SPI flash, user would need to replace
* CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC with CONFIG_MVEBU_SPL_BOOT_DEVICE_SPI
* CONFIG_ENV_IS_IN_MMC with CONFIG_ENV_IS_IN_SPI_FLASH
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-By: Dennis Gilmore <dgilmore@redhat.com>
Reviewed-By: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Remove unused I2C support in SPL and use simple_malloc functions to
reduce SPL image size.
Since Helios4 does not have any PCIe allocated on SerDes, remove PCI
support. MTD layer on top of SPI flash is not needed, remove it also.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-By: Dennis Gilmore <dgilmore@redhat.com>
Reviewed-By: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Make use of U-Boot's GPIO DM to control native GPIO and I2C IO expander.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-By: Dennis Gilmore <dgilmore@redhat.com>
Reviewed-By: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable Marvell I2C driver and I2C IO expander. Set default bus to
external I2C bus. Define I2C aliases in device tree so it can be
recognized by the driver.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-By: Dennis Gilmore <dgilmore@redhat.com>
Reviewed-By: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The lime2 features a too large capacitor on the LDO3 output, which
causes the PMIC to shutdown when enabling power. To be able to still
boot up however, we must gradually enable power on LDO3 for this board.
We do this by enabling both the inrush quirk and the maximum slope the
AXP209 supports.
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
The lime2 features a too large capacitor on the LDO3 output, which
causes the PMIC to shutdown when enabling power. To be able to still
boot up however, we must gradually enable power on LDO3 for this board.
We do this by enabling both the inrush quirk and the maximum slope the
AXP209 supports.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Enable DM_USB and DM_USB_DEV for AM57xx based boards.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch enables CONFIG_BLK as well as CONFIG_DM_MMC for the PDU001
board. It depends on Patrice Chotard's patch 'power: regulator: denied
disable on always-on regulator' which prevents power cycling the vmmc
supply. Without this patch the board will not boot as vmmc is
unfortunately used by other board components, not just eMMC and micro SD
card. Furthermore my patch 'dts: am335x-pdu001: Fix polarity of card
detection input' is required to boot from external micro SD card. Without
this patch no SD card will be detected and hence booting will fail.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>
UART booting requires YMODEM support. Add this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Implement hardware spinlock support for STM32MP1.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This is uclass for Hardware Spinlocks.
It implements two mandatory operations: lock and unlock
and one optional relax operation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Since commit 8f651ca60b ("pinctrl: stm32: Add get_pins_count() ops")
stm32f746-disco can't boot.
This is due to new memory allocation into STM32 pinctrl driver,
increase SYS_MALLOC_F_LEN from 0xC00 to 0xE00.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Enable related configs to support sata DM feature.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[YS: moveconfig -s -d]
Reviewed-by: York Sun <york.sun@nxp.com>
Enable related configs to support sata DM feature.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[YS: moveconfig.py -s -d]
Reviewed-by: York Sun <york.sun@nxp.com>
Enable related configs to support sata DM feature.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
[YS: moveconfig.py -s -d]
Reviewed-by: York Sun <york.sun@nxp.com>
Enable related configs to support sata DM feature.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
[YS: moveconfig.py -s -d]
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1012a2g5rdb/ls1012afrdm/ls1012afrwy_tfa_defconfig to be
loaded by trusted firmware
- define BOOTCOMMAND for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[YS: remove unnecessary braces]
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1012aqds_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1012ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- enable PFE validation for secure boot
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1043aqds_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1043ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- FMAN and QE address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1046aqds_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- FMAN address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1046ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- FMAN address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
Signed-off-by: York Sun <york.sun@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Add board support for Ficus EE board from Vamrs. This board utilizes
common Rock960 family support.
Following peripherals are tested and known to work:
* Gigabit Ethernet
* USB 2.0
* MMC
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
[Reworked based on common Rock960 family support]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add board support for Rock960 CE board from Vamrs. This board utilizes
common Rock960 family support.
Following peripherals are tested and known to work:
* USB 2.0
* MMC
This commit also adds DDR configuration for LPDDR3-2GiB-1600MHz which
is being used on the board.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch adds S-mode defconfigs for QEMU virt machine so
that we can run u-boot in S-mode on QEMU using M-mode runtime
firmware (BBL or equivalent).
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Bundle DTBs for R8A7795, R8A7796 ULCB variants into single U-Boot
build and let U-Boot choose between them based on the CPU model.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Bundle DTBs for R8A7795, R8A7796, R8A77965 Salvator-X variants
into the single U-Boot build and let U-Boot choose between them
based on the CPU model.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
A few Raspberry Pi specific changes this time:
- Allow 2nd MMC device
- Support RPi 3 Model A+
- Allow UUID to find filesystem
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=W6tE
-----END PGP SIGNATURE-----
Merge tag 'signed-rpi-next' of git://github.com/agraf/u-boot
Patch queue for rpi - 2018-12-03
A few Raspberry Pi specific changes this time:
- Allow 2nd MMC device
- Support RPi 3 Model A+
- Allow UUID to find filesystem
This release is fully packed with lots of glorious improvements in UEFI
land again!
- Make PE images more standards compliant
- Improve sandbox support
- Improve correctness
- Fix RISC-V execution on virt model
- Honor board defined top of ram (fixes a few boards)
- Imply DM USB access when distro boot is available
- Code cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6o9t
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-12-03
This release is fully packed with lots of glorious improvements in UEFI
land again!
- Make PE images more standards compliant
- Improve sandbox support
- Improve correctness
- Fix RISC-V execution on virt model
- Honor board defined top of ram (fixes a few boards)
- Imply DM USB access when distro boot is available
- Code cleanups
This patch switches MCR3000 board to the new DM watchdog.
The change in u-boot.lds is because MCR3000.o grows a bit
with this patch and doesn't fit anymore below env_offset on
some versions of GCC.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
This patch moves the RTC M41T62 config define to Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove CONFIG_PHY_ATHEROS and CONFIG_PHY_SMSC from defconfig
and select them in Kconfig.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Also get rid of CONFIG_SYS_NAND_SPL_KERNEL_OFFS as SPL_OS_BOOT
feature won't be used.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use DM for both MMC and USB subsystems and use dedicated DTS
for U-Boot configuration.
Disable SPL support for GPIO and remove EVMSK leftover for
DDR power control via GPIO.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Created a new header file for zcu104 RevC board and added below
configurations to use MAC address from EEPROM.
CONFIG_ZYNQ_GEM_EEPROM_ADDR
CONFIG_ZYNQ_EEPROM_BUS
Added CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET=0x20 to
xilinx_zynqmp_zcu104_revC_defconfig
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable the HS400 support code on H3, M3W, M3N Salvator-X(S)
and ULCB boards as well as E3 Ebisu board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The most generic way of having a stable boot behavior is to rely on
UUID instead of device names for root partition, so the order of
probing does not cause issues with booting.
This enables the `CMD_FS_UUID` for following defconfig files:
- rpi_0_w_defconfig
- rpi_2_defconfig
- rpi_3_32b_defconfig
- rpi_3_defconfig
- rpi_defconfig
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Alexander Graf <agraf@suse.de>
vf610twr_defconfig and vf610twr_nand_defconfig suffer from tight memory
restrictions. Disable CONFIG_EFI_LOADER for these boards.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The RK3188 rock board does not need TPL: remove TPL_TINY_MEMSET from
config.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Fixed up commit message:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The following changes are made:
- Add default bootcmd which can be used for initial start-up
- Setup necessary MTD parts for Linux compatibility
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Enable the mvpp2 Ethernet driver and the Marvell Ethernet PHY driver.
This makes the Macchiatobin 1Gb Ethernet interface usable.
Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable CONFIG_DM_SPI=y and CONFIG_DM_SPI_FLASH=y in the defconfig.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable CONFIG_DM_SPI=y and CONFIG_DM_SPI_FLASH=y in the defconfig.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable CONFIG_DM_SPI=y and CONFIG_DM_SPI_FLASH=y in the defconfig.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Commit 2b4d964718 ("arm64: mvebu: a8k: autodetect RAM size") added an
ATF query to get the detected RAM size on Armada 8K platforms. To be
usable we must have 2 DRAM banks. Set Armada 8K configurations to 2
banks.
Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
For testing purpose use zcu102 which has SD at controller 1 and this can
be used for testing this mini configuration.
U-Boot 2018.11-00279-gdc482e7ee092 (Nov 30 2018 - 10:22:56 +0100)
Model: ZynqMP MINI EMMC1
Board: Xilinx ZynqMP
DRAM: 512 MiB
EL Level: EL3
MMC: sdhci@ff170000: 0
In: dcc
Out: dcc
Err: dcc
ZynqMP>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
For testing purpose use zcu100 which has SD at controller 0 and this can
be used for testing this mini configuration.
U-Boot 2018.11-00281-gc5d48466e76e (Nov 30 2018 - 10:41:05 +0100)
Model: ZynqMP MINI EMMC0
Board: Xilinx ZynqMP
DRAM: 512 MiB
EL Level: EL3
MMC: sdhci@ff160000: 0
In: dcc
Out: dcc
Err: dcc
ZynqMP>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This configuration is useful when you want to run small u-boot and
perform DDR memory test to make sure that DDR is properly configured.
It is use for board bringup because alternative u-boot memory tests is
quite good.
Configuration is running out of OCM.
As is done for others mini configurations 0x80 bytes for variables is
enough and only default variables are stored there.
Alternative memtest is enabled and also 2GB of DDR via DTS files.
Configuration is enabling ZYNQMP_PSU_INIT_ENABLED and include psu_init()
from zcu102 for testing purpose.
In case of size issue this can be moved to SPL configuration as is done
for mini_qspi configuration but it is not a problem now.
Log:
U-Boot 2018.11-00268-gbd58b8ba8915 (Nov 29 2018 - 15:33:35 +0100)
Model: ZynqMP MINI
Board: Xilinx ZynqMP
DRAM: WARNING: Initializing TCM overwrites TCM content
2 GiB
EL Level: EL3
In: dcc
Out: dcc
Err: dcc
ZynqMP>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to have huge space for variables because none is
using that. But there are some which are setup automatically.
baudrate=115200
fdtcontroladdr=ffffa0d0
stderr=dcc
stdin=dcc
stdout=dcc
Environment size: 72/124 bytes
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Wire up mini_qspi SPL with zcu102 for testing purpose.
Normally mini u-boot runs with FSBL/SPL for certain board.
Enabling SPL and configuration from zcu102 helps with testing.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to have autoboot enabled because it should never
start anything automatically.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
