This is an init function so move it out of the common header. Avoid using
the typedef so that we don't have to include the global_data header file.
Also tidy up the function style in comments while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an arch-specific handoff header so that we can use the HANDOFF feature
on arm devices.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Exports the serdes configuration as an environment variable for LS gen 3
SoCs, so it can be used in u-boot command line. It should particularly
be useful for applying Linux DT overlays for the given serdes
configuration.
This code is called from arch_misc_init and not from the existing
serdes_init function because it depends on U-Boot environment being set
up.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently LS1028A board code uses arch_misc_init to set up the board mux
on QDS. Move this code to misc_init_r. This is consistent with LS gen 2
and T series SoCs/boards.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The arch_misc_init function is empty on LS108x SoCs/boards, remove it.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The arch_misc_init function is empty on LS2 SoCs/boards, remove it.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently LX2 board code uses arch_misc_init to set up the board mux on
RDB and QDS. Move this code to misc_init_r. This is consistent with LS
gen 2 and T series SoCs/boards.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add serdes protocol 0x7777, 0x9999, 0xb998, 0xbb56 to supported list.
These protocols are supported and functional but they trigger a warning
in U-Boot console at boot because they are not on this list.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
LS1088A has four personalities, LS1088A, LS1084A, LS1048A and LS1044A.
LS1044A, LS1048A are LS1088A personalities, which support only one
1x 10GE port.
MAC1 and MAC2 are associated with 1G SGMII, 2.5G SGMII, and XFI.
Disable MAC1 to have only one 1x 10GE port for LS1044A, LS1048A.
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
These config entries are inside the menu block, which already
depends on ARCH_LS1021A:
menu "LS102xA architecture"
depends on ARCH_LS1021A
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Program register bit of SCFG_SNPCNFGCR_USBRDSNP and
SCFG_SNPCNFGCR_USBWRSNP to drive USB read/write
snoop signal on LS1012A.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This add the initial support of the broadcom reference
board bcm968360bg with a bcm68360 SoC.
This board has 512 MB of RAM, 256 MB of flash (nand),
2 USB port, 1 UART, and 4 ethernet ports.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch bcm68360.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Use MMC0 for eMMC and MMC2 for SD-card as other Exynos-based boards do.
This allows to use common code to get MMC device id based on the XOM[7:5]
pins.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Card detect line for SD-card on Odroid U3/X2 boards are active low, so
add cd-inverted property to indicate this, as u-boot's GPIO driver doesn't
support specifying line polarity. This restores S5P_SDHCI driver operation
on Odroid U3/X2 boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
u-boot uses the same DTS for the all Odroid XU3-based boards, so list
them in the model description to let user know that those boards are
supported.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The ST-Ericsson U8500 SoC has been used in mass-production for
some Android smartphones released around 2012.
In particular, Samsung has released more than 5 different
smartphones based on U8500, e.g.
- Samsung Galaxy S III mini (GT-I8190) "golden"
- Samsung Galaxy S Advance (GT-I9070) "janice"
- Samsung Galaxy Xcover 2 (GT-S7710) "skomer"
and a few others.
Mainline Linux has great support for the Ux500 SoC, so these
smartphones can also run Linux mainline quite well.
Unfortunately, the original Samsung bootloader used on these devices
has limitations that prevent booting Linux mainline directly.
It keeps the L2 cache enabled, which causes Linux to crash very early,
shortly after decompressing the kernel.
Using U-Boot allows to circumvent these limitations. We can let the
Samsung bootloader chain-load U-Boot and U-Boot locks the L2 cache
before booting into Linux. U-Boot has several other advantages
- it supports device-trees directly and we are no longer limited to
flashing Android boot images through Samsung's proprietary download
mode.
The Samsung "stemmy" board covers all Samsung devices based on U8500.
Add minimal support for "stemmy". For now only UART is supported but
this will be extended later.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The NovaThor U8500 SoC was released by ST-Ericsson in 2011.
It was used for some development boards like the CALAO Systems
Snowball SBC, but mass production was primarily for Android
smartphones like the Samsung Galaxy S III mini.
Previous support for U8500 was removed in
commit 68282f55b8 ("arm: Remove unused ST-Ericsson u8500 arch")
since none of the boards were converted to generic boards
before the deadline.
The new code does not have much in common with the previous code.
I have completely rewritten everything, embracing the Driver Model
and device trees wherever possible.
The U8500 support is a bit more minimal for now - my primary
use case is to use U-Boot as alternative bootloader for some of the
U8500 Samsung smartphones. At the moment U-Boot is chain-loaded from
the original Samsung bootloader. A side effect of this is that we
can (temporarily) get away without implementing some functionality
- e.g. all clocks are already enabled by the original bootloader.
More functionality will be added in future patches.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: John Rigby <john.rigby@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
from https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson.git/
tag "ux500-armsoc-v5.6-2"
commit 224bf0fe7292 ("ARM: dts: ux500: samsung-golden: Add Bluetooth")
(queued for merge in Linux 5.6)
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Set the kernel device-tree file (fdtfile environment variable) based on
run-time detection of the platform.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Add device-tree description for the EEPROM devices on Armada 388 SOM rev
2.1.
Another EEPROM is now on Clearfog Pro carrier rev 2.2, and Clearfog Base
rev 1.3.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
K3 J721E:
* DMA support.
* MMC and ADMA support.
* EEPROM support.
* J721e High Security EVM support.
* USB DT nodes
K3 AM654:
* Fixed boot due to pmic probe error.
* USB support and DT nodes.
* ADMA support
DRA7xx/AM57xx:
* BBAI board support
* Clean up of net platform code under board/ti
AM33/AM43/Davinci:
* Reduce SPL size for omap3 boards.
* SPL DT support for da850-lcdk
* PLL divider fix for AM335x
Functions fracpll_configure(), decode_intpll(), decode_fracpll(),
get_root_src_clk() and get_root_clk() are used only in the scope of this
file, so make them static to fix the following sparse warnings:
arch/arm/mach-imx/imx8m/clock_imx8mm.c:50:5: warning: no previous
prototype for ‘fracpll_configure’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:271:5: warning: no previous
prototype for ‘decode_intpll’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:418:5: warning: no previous
prototype for ‘decode_fracpll’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:483:5: warning: no previous
prototype for ‘get_root_src_clk’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:527:5: warning: no previous
prototype for ‘get_root_clk’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
The mux mode is embedded in the PAD definition and therefore there is
no need to repeat it in the PAD configuration value (more over since
this information will be masked out when the configuration value is
applied).
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
On SPL enabled systems, the current s_init code (wdog, clock and ldo
init) is executed twice (by SPL and u-boot). This is not necessary and
might lead to boot issues (ie, starting PMC1 when it is already running).
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add iMX6ULL VisionSOM SoM and VisionCB-RT-STD evaluation board support.
The SoM has an iMX6ULL, 512 MiB of DRAM and microSD slot. The carrier
board has Ethernet, USB host port, USB OTG port.
Signed-off-by: Arkadiusz Karas <arkadiusz.karas@somlabs.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add pinmux for USB1 and enable it as a peripheral port in U-Boot
specific dtsi since U-Boot does not support OTG.
Disable USB0 as its not available on the baseboard.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for USB0 and USB1 instances on the AM6 SoC.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
None of these boards boot, but the solution appears to be the same.
All the boards have SPL that is too large. With a few defconfig
options removed, these corresponding options can be removed from
their respective SPL dtb files.
This patch unifies the DM37/OMAP35 boards' -u-boot.dtsi files
to remove gpio's, i2c, bandgap, thermal zones, unneeded uarts, and
unneeded MMC nodes.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The memory allocated to store the FIT image containing SYSFW and board
configuration data is statically defined to the largest size expected.
This was 276000 bytes but now needs to be grown to 277000 to make room
for the slightly larger SYSFW image used on J721e High-Security devices.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
ROM configures certain firewalls based on its usage, which includes
the one in front of boot peripherals. In specific case of boot
peripherals, ROM does not open up the full address space corresponding
to the peripherals. Like in OSPI, ROM only configures the firewall region
for 32 bit address space and mark 64bit address space flash regions
as in-accessible.
When security-cfg is initialized by sysfw, all the non-configured
firewalls are kept in bypass state using a global setting. Since ROM
configured firewalls for certain peripherals, these will not be touched.
So when bootloader touches any of the address space that ROM marked as
in-accessible, system raises a firewall exception causing boot hang.
It would have been ideal if sysfw cleans up the ROM configured boot
peripheral firewalls. Given the memory overhead to store this
information provided by ROM and the boot time increase in re configuring
the firewalls, it is concluded to clean this up in bootloaders.
So disable all the firewalls that ROM doesn't open up the full address
space.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Venkateswara Rao Mandela <venkat.mandela@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This file used to be the common location for K3 init when AM6 was the
only device, but common code was moved to common.c and this file became
AM6 specific, correct this header text.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
wkup_vtm populates only 1 power-domain cell in it's node. But the
power-domain cell are defined as 2. Due to this the following warning
comes during build:
arch/arm/dts/k3-am654-r5-base-board.dtb: Warning (power_domains_property):
/interconnect@100000/interconnect@28380000/interconnect@42040000/
wkup_vtm@42050000:power-domains: property size (8) too small for cell size 2
Fix this by updating the power-domain cells.
Fixes: cfa6bd549c ("arm: dts: k3-am654-r5-base-board: Add VTM node")
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
On K3 systems U-Boot runs on both an R5 and a large ARM cores (usually
A53 or A72). The large ARMs are coherent with the DMA controllers and
the SYSFW that perform authentication. And previously the R5 core did
not enable caches. Now that R5 does enable caching we need to be sure
to clean out any of the image that may still only be in cache before we
read it using external DMA for authentication.
Although not expected to happen, it may be possible that the data was
read back into cache after the flush but before the external operation,
in this case we must invalidate our stale local cached version.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Not finding a node that we try to disable does not always need to be
fatal to boot but should at least print out a warning. Return error
from fdt_disable_node as it did fail to disable the node, but only
warn in the case of disabling the TRNG as this will not prevent boot.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Make the wkup_i2c0 module usable across all stages of U-Boot by adding
the needed definitions including the associated pinmux definitions.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The TI J721E EVM system on module (SOM), the common processor board, and
the associated daughtercards have on-board I2C-based EEPROMs containing
board config data. Use the board detection infrastructure to do the
following:
1) Parse the J721E SOM EEPROM and populate items like board name, board
HW and SW revision as well as board serial number into the TI common
EEPROM data structure residing in SRAM scratch space
2) Check for presence of daughter card(s) by probing associated I2C
addresses used for on-board EEPROMs containing daughter card-specific
data. If such a card is found, parse the EEPROM data such as for
additional Ethernet MAC addresses and populate those into U-Boot
accordingly
3) Dynamically apply daughter card DTB overlays to the U-Boot (proper)
DTB during SPL execution
4) Dynamically create an U-Boot ENV variable called name_overlays
during U-Boot execution containing a list of daugherboard-specific
DTB overlays based on daughercards found to be used during Kernel
boot.
This patch adds support for the J721E system on module boards containing
the actual SoC ("J721EX-PM2-SOM", accessed via CONFIG_EEPROM_CHIP_ADDRESS),
the common processor board ("J7X-BASE-CPB"), the Quad-Port Ethernet
Expansion Board ("J7X-VSC8514-ETH"), the infotainment board
("J7X-INFOTAN-EXP") as well as for the gateway/Ethernet switch/industrial
expansion board ("J7X-GESI-EXP").
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
BeagleBoard.org BeagleBone AI is an open source hardware single board
computer based on the Texas Instruments AM5729 SoC featuring dual-core
1.5GHz Arm Cortex-A15 processor, dual-core C66 digital signal
processor (DSP), quad-core embedded vision engine (EVE), Arm Cortex-M4
processors, dual programmable realtime unit industrial control
subsystems and more. The board features 1GB DDR3L, USB3.0 Type-C, USB
HS Type-A, microHDMI, 16GB eMMC flash, 1G Ethernet, 802.11ac 2/5GHz,
Bluetooth, and BeagleBone expansion headers.
For more information, refer to:
https://beaglebone.ai
The corresponding patch against the mainline linux kernel can be found
at: https://patchwork.kernel.org/patch/11254903/
This patch introduces the BeagleBone AI device tree.
Note that the device use the "ti,tpd12s016" component which is software
compatible with "ti,tpd12s015". Thus we only use the latter driver.
Signed-off-by: Jason Kridner <jdk@ti.com>
Signed-off-by: Caleb Robey <c-robey@ti.com>
Cc: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
These are necessities for beaglebone ai boot. There is the addition of
CONFIG_SUPPORT_EMMC_CONFIG to the Kconfig file. This is present upstream
but not in 19.01 yet.
Signed-off-by: Jason Kridner <jdk@ti.com>
Signed-off-by: Caleb Robey <c-robey@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Get clk_xin by name instead of by index to avoid having to put clocks in
the same order in all devices.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Currently, the da850-lcdk uses SPL_OF_PLATDATA and manually loads
the necessary source code instead of using the auto-generated,
because the drivers don't properly autogenerate the code.
This patch simply enables the various device tree options to
mimic the da850-evm which doesn't need or use OF_PLATDATA for
device tree support. It does not disable OF_PLATDATA.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
J721e has two instances of Cadence USB3 controller. Add DT nodes for the
same. USB0 is configured to device mode and USB1 is configured to host
mode. For now only high speed mode is supported.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
This function related to timer and most of the timer functions are in
time.h, so move this function there.
Signed-off-by: Simon Glass <sjg@chromium.org>
These three clock functions don't use driver model and should be migrated.
In the meantime, create a new file to hold them.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is only used on ARM devices so does not belong in the global
common header file. Move it to an ARM header.
Signed-off-by: Simon Glass <sjg@chromium.org>
These functions relate to setting up the device tree for booting the OS.
The fdt_support.h header file supports similar functions, so move these
there.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is an init function so move it out of the common header. Avoid using
the typedef so that we don't have to include the global_data header file.
Also tidy up the function style in comments while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add missing 'eth-ck' clock to the ethernet node. These clock are used to
generate external clock signal for the PHY in case 'st,eth_ref_clk_sel'
is specified.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Until now, we only support aes128. This commit add the support
of aes192 and aes256.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Split the board and SOC support for STM32MP15x family and
prepare the introduction of new boards with STM32MP15x.
This path define the 2 configurations:
- STM32MP15x: STM32MP15x soc support (new)
- TARGET_ST_STM32MP15x: STMicroelectronics board support (choice)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Let board code override setup_mac_address(), which is useful e.g. if the
board derives the MAC address from another source, like an I2C EEPROM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The main prompt for this (defined in /Kconfig) is visible at all times,
which means there's no reason to have an additional, machine-specific
prompt to set the same option.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
SoC base addresses should better go into a common SoC file instead
of repeating the definition in each board file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This patch move u-boot properties to -u-boot.dtsi file.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
This adds a general board file based on MT7622 SoCs from MediaTek.
This commit is adding the basic boot support for the MT7622 rfb.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Add support for MediaTek MT7622 SoC. This include the file
that will initialize the SoC after boot and its device tree.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
This adds a general board file based on MT8512 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
This commit is adding the basic boot support for the MT8512 eMMC board.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
Add support for MediaTek MT8512 SoC. This include the file
that will initialize the SoC after boot and its device tree.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
The eSDHC reference clocks should be provided by speed.c in arch/.
And we do not need CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK option to
select which clock to use. Because we can make the driver to select
the periperhal clock which is better (provides higher frequency)
automatically if its value is provided by speed.c.
This patch is to drop this option and make driver to select clock
automatically. Also fix peripheral clock calculation issue in
fsl_lsch2_speed.c/fsl_lsch3_speed.c.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The QorIQ eSDHC controller supports two reference clocks. They are
platform clock and periperhal clock. The global variable sdhc_clk
has already been used for platform clock.
This patch is to add another global variable sdhc_per_clk for
periperhal clock, which provides higher frequency and is required
to be used for SD UHS and eMMC HS200/HS400 speed modes.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The below patch added eSDHC periperhal clock code initially.
2d9ca2c mmc: fsl_esdhc: Add peripheral clock support
The purpose was to fix up device tree properties "peripheral-frequency"
so that linux could get the periperhal clock by it.
However the implementation on both u-boot and linux was only
for a Freescale SDK release. The linux part implementation had never
been upstreamed. These code should not have been exist on u-boot
mainline.
Let's remove the powerpc part changes but keep the changes in
fsl_esdhc driver. The changes in fsl_esdhc driver could be utilized
to support SD UHS and eMMC HS200/HS400 speed modes for current
Layerscape ARM platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Since some driver requires this function add it as an empty stub
when DCACHE is OFF.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
IPG clock description is missing for I2C0 and I2C2 busses,
add it. Otherwise we see -ENODATA error when trying to get
I2C clock for these busses.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
imx6ul-14x14-evk does not have a GPIO dedicated for reading the card
detect pin on the eSDHC2 port. In such cases the "broken-cd" property
must be passed, otherwise the card cannot be detected.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
All Tegra chips except Tegra186 have a tegraNNN-u-boot.dtsi. Duplicate
Tegra210's copy of this file for Tegra186. This ensures that a /binman node
exists in U-Boot's control DT. Subsequent to 3c10dc95bd ("binman: Add a
library to access binman entries") this appears to be required. I haven't
really investigated why all this is necessary or how it works, but simply
observed the boot failure listed below, bisected it, noticed the
inconsistency in DT files, and found that fixing it resolved the boot
issue.
U-Boot 2020.01-rc4-00256-g3c10dc95bdd0 (Jan 07 2020 - 10:25:00 -0700)
SoC: tegra186
Model: NVIDIA P2771-0000-500
Board: NVIDIA P2771-0000
DRAM: 7.8 GiB
initcall sequence 00000000fffb7858 failed at call 00000000800955a8 (err=-22)
### ERROR ### Please RESET the board ###
Fixes: 3c10dc95bd ("binman: Add a library to access binman entries")
Fixes: f2faffecb0 ("binman: tegra: Convert to use binman")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch is to build the coresight topology structure of zynq-7000
series according to the docs of coresight and userguide of zynq-7000.
Signed-off-by: Zumeng Chen <zumeng.chen@windriver.com>
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Most of the legacy "gpio-key,wakeup" boolean property is already
replaced with "wakeup-source". However few occurrences of old property
has popped up again, probably from the remnants in downstream trees.
This patch replaces the legacy properties with the unified
"wakeup-source" property introduced by:
"Input: gpio_keys - switch to using generic device properties"
(sha1: 700a38b27eefc582099fdf69effacfad0ad738a4)
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Somewhere along recent changes to power control of the wl1831, power-on
became very unreliable on the Ultra96, failing like this:
wl1271_sdio: probe of mmc2:0001:1 failed with error -16
wl1271_sdio: probe of mmc2:0001:2 failed with error -16
After playing with some dt parameters and comparing to other users of
this chip, it turned out we need some power-on delay to make things
stable again. In contrast to those other users which define 200 ms,
Ultra96 is already happy with 10 ms.
Fixes: 5869ba0653b9 ("arm64: zynqmp: Add support for Xilinx zcu100-revC")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
s/_/-/ for node names.
It fixes warnings like this:
... Warning (node_name_chars_strict): /cpu_opp_table:
Character '_' not recommended in node name ...
Issues reported by make dtbs W=12
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The 'arm,armv8' compatible string is only for software models. It adds
little value otherwise and is inconsistently used as a fallback on some
platforms. Remove it from those platforms.
This fixes warnings generated by the DT schema.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Chanho Min <chanho.min@lge.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
zcu102-revB/up are not removing phy from revA properly because of incorrect
name.
Fixes: 2975a42b42 ("arm64: zynqmp: Use ethernet-phy as node name for ethernet phys")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
zcu1285 is the same as zcu1275 but it is using Avnet FMC
http://www.ultrazed.org/product/network-fmc-module
Unfortunately not everything is connected now that's why this is only
describing system which Xilinx is using.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>