Add sc_pm_is_partition_started to check whether a partition
has been started. This will be used to detect M4 partition booted up or
not, then we could choose which dtb to use. If M4 is up, we need
use dtb, such as imx8qm-mek-rpmsg.dtb.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add OP-TEE device tree node for Linux according to args passed from ATF.
If ATF has been built with OP-TEE running, boot_pointer[1] will indicate
that.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On i.MX8QM, sid is programmable, so we could program sid according the
value encoded in device tree.
This patch support legacy bindings which are still being used by XEN
and new bindings used by Linux Kernel.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When resource is not assigned to non-secure Linux, if linux continue
to use the node, linux may crash or hang. So need to set the node
status to disabled for not owned resources.
The resource id is in the power-domains property in device tree,
so parse the power-domains property to get the resource id and
use scfw api to check whether it is owned by current partition.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since SCU MU driver has been bound in dm_init, so we don't need to
bind it again. Just replace by using uclass function to probe it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To support SPL loading container file, add a new Makefile target,
and introduce a new Kconfig file to source the cfg file which
will be parsed by mkimage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add parsing i.MX8 Container file support, this is to let
SPL could load images in a container file to destination address.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The changes were added by following patch:
commit <9002e735e717> ("imx: mx6sabresd: fix boot hang with video")
commit <f45ec8fcfb86> ("imx6: dts: add 'u-boot, dm-pre-reloc' to soc and ipu nodes")
Let's move the U-Boot specific change to imx6qdl-u-boot.dtsi
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move CONFIG_CSF_SIZE to Kconfig and define default value as 0x4000.
mx8mqevk requires 0x2000 add this configuration in imx8mq_evk_defconfig
file.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
On i.MX7ULP B0, there is change in NIC clock dividers architecture.
On A0, the NIC1 BUS and EXT dividers were in a chain with NIC1 DIV, but
on B0 they are parallel with NIC1 DIV. So now the dividers are independent.
This patch modifies the scg_nic_get_rate function according to this change.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
The normal target frequency for ULP A7 core is 500Mhz, but now ROM
set the core frequency to 413Mhz. So change it to 500Mhz in u-boot.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The GPU uses APLL PFD2 as its clock parent (483.84Mhz) with divider
set to 1. This frequecy is out of ULP A0 spec. The MAX rate for GPU
is 350Mhz. So we simply configure the APLL PFD2 to 345.6Mhz (FRAC=28)
to workaround the problem. The correct fix should let GPU handle the
clock rate in kernel.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The num/denom is a float value, but in the calculation it is convert
to integer 0, and cause the result wrong.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Wrong I2c driver configuration name is used in codes, so I2c driver is
not built. Correct it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since many drivers need this CONFIG_MX7ULP to distiguish the settings
for i.MX7ULP only. Add this entry to cpu's kconfig.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The offset for FRAC and the mask for PCD are not correct.
If we set FRAC, we can't get the right frequency. Fix them
to correct value.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On i.MX7ULP, value zero is reserved in SCG1 RCCR register,
so the val should be decreased by 1 to get the correct clock
source index.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The board will reboot if A7 core enter mem mode by rtc, then M4 core
enter VLLS mode after the RTC alarm expired. Enable the dumb PMIC mode
to fix this issue.
Since i.MX7ULP B0 moves the SNVS LP into M4 domain, A core can't access
it. So check the CPU rev and not apply the settings for B0.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Previously the SPL size on all iMX6 platforms was restricted to 68KB
because the OCRAM size on iMX6SL/DL parts is only 128KB. However, the
other iMX6 variants have 256KB of OCRAM. Add an option
CONFIG_MX6_OCRAM_256KB which allows using the full size on boards which
don't need to support the SL/DL variants. This allows for an SPL size of
196KB, which makes it much easier to use configurations such as SPL with
driver model and FDT control.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Tested-by: Adam Ford <aford173@gmail.com> #imx6q_logic
There is no need to use HAB for FIT signature validation when
SPL_FIT_SIGNATURE is also enabled, as that will be validated via the
normal U-Boot signed FIT image flow.
This allows having SPL validated by HAB and the payloads to follow
being validated with FIT signatures only.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Toradex Apalis iMX6 modules are available in the iMX6D and iMX6Q
variants, which are quite similar and already managed via only one
dtb in u-boot (imx6-apalis.dtb). Select MX6Q via Kconfig by default in
order to automatically enable the HAS_CAAM and MX6_SMP features.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
The gpio command currently uses equal bank names "GPIO0_"
for all existing gpio banks, i. e.:
U-Boot# gpio status -a
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: input: 0 [ ]
...
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: input: 0 [ ]
...
So the command is broken, it is not possible to address
a desired bank. Add gpio aliases to fix this.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Pass spl_image and bootdev to board_return_bootrom.
i.MX8MN needs the args to let ROM to load images
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
To support DM_VIDEO,
Add display node for lcdif
Drop board iomuxc settings.
Enable DM_VIDEO
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Add i.MX6ULZ board support. the i.MX6ULZ is SW compatible
with i.MX6ULL. so most code of i.MX6ULL can be reused
by i.MX6ULZ.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add i.MX6ULZ cpu type and helper.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Import kernel dts for i.MX6ULZ from
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Sync kernel dts for i.MX6ULL from
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Sync kernel dts for i.MX6UL from
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Move the exisiting function of getting board dtb from versal to a common
Xilinx folder.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
With new mailbox driver PMUFW configuration object can be loaded via the
same interface and there is no need to have pmu_ipc.c completely.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Probe ZynqMP firmware driver on the board initialization phase and
ensure that firmware is in place to continue execution. The probing is
done on board_init so it can be used for both SPL and U-Boot proper.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Removes the old function to get the firmware version.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
New firmware header to place firmware specific macro and function
declarations. The patch also moves the macros defining PM operations as
well as some helper macros.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Cleanup PM ID handling by using enum values.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The following patch adds a mailbox node and firmware node to following the
mainline DT.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
zynqmp-power driver for ZynqMP to handle the communication with the PMU
firmware. Firmware driver just probes subnodes and power driver handles
communication with PMU using the IPI mailbox driver.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP mailbox driver implementing IPI communication with PMU. This would
allow U-Boot SPL to communicate with PMUFW to request privileged
operations.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Setup initrd_high and fdt_high to be placed in lowmem space for kernel to
be able to reach it. Values are setup at run time to ensure that the same
setting can be used on different memory setup. Do this setting only when
variables are not
Similar run time detection was done for Zynqmp and Versal.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to use private code for standard bootm command.
Current implementation is also broken and don't support image relocation
properly. Switching to generic bootm implementation is fixing these issues.
cmdline and bdt bootm subcommands are returning -1 because they are not
implemented.
Similar change was done long time ago by for example commit 2bb5b63879
("MIPS: bootm: rework and fix broken bootm code")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
arch_lmb_reserve() protects U-Boot relocated code with stack not to be used
for image relocation.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Similar SCs but different wiring.
- dc_i2c is connected to X-PRC cards that's why label is required to have
an option to hook up some devices.
- Exactly identify i2c devices on x-prc boards.
In case of missing i2c connection devices won't be accessible.
- USB 0 should be device mode with super speed.
- USB 1 should be host mode.
- Fix i2c mux reset pin entry - commented, not verified.
- Fix i2c1 eeprom compatible string - it is an ST 128Kbit device.
Need to use atmel fallback.
- Fix si570 I2C slave address and add corresponding part numbers.
- Enable AMS for system monitoring.
- phy reset property should be commented because it will throw a
warning dump when called from context that can sleep.
No support for phys property (zynqmp phy driver) with SGMII.
Add is-internal-pcspma property required by uboot.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Change has been done across the whole tree only zynqmp-mini-qspi hasn't
been fixed.
Origin changed done by commit ffd4c7c2ec
("dts: switch spi-flash to jedec, spi-nor compatible")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added alias for usb node in dts file.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds clock driver support for Versal platform. The clock driver
queries and performs clock operations using PLM firmware by communicating
with it using SMC calls.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch provides an option to enable/disable OCM and TCM memory into MMU
table with corresponding memory attributes.
The same change was done for ZynqMP by commit 189bec47ab
("arm64: zynqmp: Provide a Kconfig option to define OCM and TCM in MMU")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Code reads DT and setup MMU table based on memory node. This will ensure
that only DT needs to be changed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is setting up the initrd_high to as high as possible by leaving
max stack size for u-boot so that bigger rootfs can also be loaded by
u-boot for booting kernel.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is setting up the initrd_high to as high as possible by leaving
max stack size for u-boot so that bigger rootfs can also be loaded by
u-boot for booting kernel.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define board_late_init which performs bootmode detection
and prepares corresponding distro boot commaand sequence.
Also disable it for mini platforms because simply there is no need to have
it enabled.
But also disable it for virtual platform because Qemu is not modelling this
register space that's why travis testing would fail. This configuration
should be reverted when mainline Qemu is updated.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This node is used by qspi driver for supporting qspi boot mode in SPL.
Similar changes have beeen done by commit a9022b017a
("ARM64: zynqmp: Add u-boot,dm-pre-reloc to clk nodes")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The sam9x60 qspi controller uses 2 clocks, one for the peripheral register
access, the other for the qspi core and phy. Both are mandatory.
Enable the qspi node together with the SST26VF064B qspi nor flash
memory. Booting from the QSPI NOR flash is now possible.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
sama5's SFR has at offset 0x04 the DDR Configuration Register,
while sam9x60's SFR contains the EBI Chip Select Register. Add
a union to reconcile both boards.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The Special Function Registers (SFR) are present in sam9x5 and
sam9x60 too, rename sama5_sfr to at91_sfr.h.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add new board SAM9X60-EK using the ARM926 SAM9X60 SoC.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
[tudor.ambarus@microchip.com:
- fix number of DRAM banks:
One DDR2-SDRAM (W972GG6KB 2 Gbit = 16 Mbit x 16 x 8 banks]
- drop SPL related macros
- drop memtest macros
- drop CONFIG_SPI_BOOT, CONFIG_SYS_USE_DATAFLASH related macros
- drop inclusion of asm/arch/at91sam9_smc.h]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add Ethernet controller to dtsi file and enable it on sam9x60ek
platform connected with rmii.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
add device tree files for sam9x60ek board with below changes.
- Add initial device nodes (pmc, pinctrl, sdhc, dbgu & pit)
- Add the reg property for the pinctrl node.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
[prasanthi.chellakumar@microchip.com: fix style/whitespace issues]
Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com>
[nicolas.ferre@microchip.com:
- fix gclk,
- fix pio/pinctrl controller definition and allow to have more
than only PIOA for this SoC,
- removing pinctrl address]
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[claudiu.beznea@microchip.com:
- use SAM9X60's compatible for pinctrl
- add drive strength and slew rate options for SDMMC0 pins.]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
[tudor.ambarus@microchip.com:
- u-boot,dm-pre-reloc property in dedicated file,
- fix pit len, starts from 0xFFFFFE40 and it is of len 0x10]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add node for hlcld for u-boot logo display at boot.
This is compatible with the Precision Design Associates (PDA) TM5000 screen.
Timings are compatible with simple panel from Linux, panel name is
pda_91_00156_a0
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
qspi1 does not have an alias/seq number. This is required for
SPL default SF bus booting for the boards that have this SoC
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add a function in SFR implementation that will open the DDR input
buffers.
This can be called at DRAM initialization time.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add support for the SAMA5D27-WLSOM1-EK. It's based on the Microchip
WireLess SoM which contains the SAMa5D27 LPDDR2 2Gbits SiP.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[eugen.hristev@microchip.com]: added u-boot specific dtsi and ported to 2019.10
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
With FSP2 we use MTRRs in U-Boot proper even though the 32-bit init
happens in TPL. Enable this, using a variable to try to make the
conditions more palatable.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We don't need this driver very early in boot and it adds code size. Drop
it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Normally U-Boot handles MTRRs through an add/commit process which
overwrites all MTRRs. But in very early boot it is not desirable to clear
the existing MTRRs since they may be in use and it can cause a hang.
Add a new mtrr_set_next_var() function which sets up the next available
MTRR to the required region.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: pass 'type' to set_var_mtrr() in mtrr_set_next_var()]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Move the code that actually sets up the MTRR into another function so it
can be used elsewhere in the file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present these uclasses assumes that they are used with a device tree.
Update them to support of-platdata as well.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The code in swapcase can be used by other sandbox drivers. Move it into a
common place to allow this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: remove inclusion of <asm/test.h> in pci_sandbox.c]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Add a few more CPU functions that are common on Intel CPUs. Also add
attribution for the code source.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add missing MSR_IA32_MISC_ENABLE write back in cpu_set_eist();
fix 2 typos in cpu_get_burst_mode_state() comments]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Some MSR registers are defined twice in different parts of the file. Move
them together and remove the duplicates. Also drop some thermal defines
which are not used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These functions are the same on modern Intel CPUs, so use common code to
set them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: return false instead of 0 in cpu_ivybridge_config_tdp_levels();
fix 'muiltiplier' and 'desgn' typos]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Modern Intel CPUs use a standard bus clock value of 100MHz, so put this in
a common file and tidy up the copies.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This code appears in a few places, so move it to a common file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This parameter is needed by the PCI driver-mode interface but is always
NULL on x86. There are a number of calls to this function so it makes
sense to minimise the parameters.
Adjust the x86 function to omit the first parameter, and introduce stub
functions to handle the conversion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: rebase the patch against u-boot-x86/next to get it applied cleanly]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present this hedaer is only available on x86. To allow sandbox to use
it for testing, move it to a common location.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is currently a decimal value which is not as convenient or
meaningful. Also U-Boot tends to use hex everywhere.
Convert this option to hex and add a comment for the size_check macro.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct the typo in the commit title]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present there is only one control for this and it is used for both SPL
and TPL. But SPL might have a lot more space than TPL so the extra cost of
a full printf() might be acceptable.
Split the option into two, providing separate SPL and TPL controls. The
TPL setting defaults to the same as SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present this is defined in Kconfig but there is a separate one in the
CONFIG whitelist. It looks like these are duplicates.
Rename the non-Kconfig one and remove it from the whitelist.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present PCI address transaction is not supported so drivers must
manually read the correct BAR after reading the device tree info. The
ns16550 has a suitable implementation, so move this code into the core
DM support.
Note that there is no live-tree equivalent at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct the unclear comments in test.dts]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Sandbox pci works using emulation drivers which are currently children of
the pci device:
pci-controller {
pci@1f,0 {
compatible = "pci-generic";
reg = <0xf800 0 0 0 0>;
emul@1f,0 {
compatible = "sandbox,swap-case";
};
};
};
In this case the emulation device is attached to pci device on address
f800 (device 1f, function 0) and provides the swap-case functionality.
However this is not ideal, since every device on a PCI bus has a child
device. This is only really the case for sandbox, but we want to avoid
special-case code for sandbox.
Worse, child devices cannot be probed before their parents. This forces
us to use 'find' rather than 'get' to obtain the emulator device. In fact
the emulator devices are never probed. There is code in
sandbox_pci_emul_post_probe() which tries to track when emulators are
active, but at present this does not work.
A better approach seems to be to add a separate node elsewhere in the
device tree, an 'emulation parent'. This could be given a bogus address
(such as -1) to hide the emulators away from the 'pci' command, but it
seems better to keep it at the root node to avoid such hacks.
Then we can use a phandle to point from the device to the correct
emulator, and only on sandbox. The code to find an emulator does not
interfere with normal pci operation.
Add a new UCLASS_PCI_EMUL_PARENT uclass which allows finding an emulator
given a bus, and finding a bus given an emulator. Update the existing
device trees and the code for finding an emulator.
This brings PCI emulators more into line with I2C.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fix 3 typos in the commit message;
encode bus number in the labels of swap_case_emul nodes;
mention commit 4345998ae9 in sandbox_pci_get_emul()]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present these functions are stubbed out. For more comprehensive testing
with PCI devices it is useful to be able to fully emulate I/O access. Add
simple implementations for these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: change to use 'const void *' in sandbox_write();
cast 'addr' in read/write macros in arch/sandbox/include/asm/io.h;
remove the unnecessary cast in readq/writeq in nvme.h]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Increase the memory space so we can support the p2sb bus which needs
multiples of 1MB.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
U-Boot already supports using -D to indicate that it should use the normal
device tree. It is sometimes useful to run with the test device tree, e.g.
when running a test. Add a -T option for this along with some
documentation.
It can be used like this:
/tmp/b/sandbox/u-boot -T -c "ut dm pci_busdev"
(this will use /tmp/b/sandbox/arch/sandbox/dts/test.dtb as the DT)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
These functions are available on x86 but not sandbox. They are useful
shortcuts and clarify the code, so add them to sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Rename this ID to SANDBOX_PCI_SWAP_CASE_EMUL_ID since it is more
descriptive and allows us to add new PCI emulators without any conflict or
confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present address translation does not work since there is no ranges
property in the spmi nodes. Add empty ranges properties and a little more
logging so that this shows the error:
/tmp/b/sandbox/u-boot -d /tmp/b/sandbox/arch/sandbox/dts/test.dtb \
-c "ut dm spmi_access_peripheral" -L7 -v
...
pm8916_gpio_probe() bad address: returning err=-22
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
We have a 'safe' version of this function but sometimes it is not needed.
Add a normal version too and update a few places that can use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This MSR number is used on most modern Intel processors, so drop the
confusing NHM prefix (which might mean Nehalem).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: drop MSR_IVT_TURBO_RATIO_LIMIT as no code uses it]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Add some new MTRRs used by Apollolake as well as a mask for the MTRR
type.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The full start-up sequence (TPL->SPL->U-Boot) can be a bit confusing since
each phase has its own 'start' file. Add comments to explain this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present we assume that CAR (Cache-as-RAM) is used if HOBs (Hand-off
blocks) are not, since HOBs typically indicate that an FSP is in use, and
FSPs handle the CAR init.
However this is a bit indirect, and for FSP2 machines which use their own
CAR implementation (such as apollolake) but use the FSP for other
functions, the logic is wrong.
To fix this, add a dedicated Kconfig option to indicate when CAR is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fix a typo in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
The useable RAM is calculated when the RAM is inited. Save this value so
that it can be easily used in U-Boot proper.
Also save a pointer to the hob list so that it is accessible (before
relocation only) in U-Boot proper. This avoids having to scan it in SPL,
for everything U-Boot proper might need later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: guard handoff_arch_save() with IS_ENABLED(CONFIG_USE_HOB)]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
When TPL is running, broadwell needs to do different init from SPL. There
is no need for this code to be in the generic x86 SPL file, so move it to
arch_cpu_init().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This image loader works on systems where the flash is directly mapped to
the last part of the 32-bit address space. On recent Intel systems (such
as apollolake) this is not the case.
Reduce the priority of this loader so that another one can override it.
While we are here, rename the loader to BOOT_DEVICE_SPI_MMAP since
BOOT_DEVICE_BOARD is not very descriptive.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use the standard hang() function when booting fails since this implements
the defined U-Boot behaviour for this situation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the x86 pre-DM equivalent of pci_bus_clrset_config32() does not
exist. Add it to simplify PCI init code on x86.
Also add the missing functions to this header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useful in SPL and TPL to access symbols from binman, such as the
position and size of an entry in the ROM. Collect these symbols together
in the SPL binaries.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add cpu_intel_get_info() to find out the CPU info on modern Intel CPUs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add parameter and return value descriptions]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
With FSP2 the non-volatile storage used by the FSP to init memory can be
split into a fixed piece (determined at compile time) and a variable piece
(determined at run time). Add support for reading the latter.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some of this file can be shared between FSP1 and FSP2. Move it into a
shared file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Some of this file can be shared between FSP1 and FSP2. Move it into a
shared file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Most of the DRAM functionality can be shared between FSP1 and FSP2. Move
it into a shared file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: rebase the patch against u-boot-x86/next to get it applied cleanly]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
The comments in the FSP code use a different style from the rest of the
x86 code. I am not sure it this is intentional.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fix 2 comment style issues]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Update a few #ifdefs to if() to improve build coverage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: recover the codes that got wrongly deleted in dram_init()]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Many support functions are common between FSP1 and FSP2. Add a new header
to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: remove forward declarations in fsp_support.h]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Given these exported function an fsp_ prefix since they are declared in an
fsp.h header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
At present there is an arch-specific area in the SPL handoff area intended
for use by arch-specific code, but there is no explicit call to fill in
this data. Add a hook for this.
Also use the hook to remove the sandbox-specific test code from
write_spl_handoff().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This include file is only used for FSP v1. Avoid including it from
fdt_support.h so we can use the latter with FSP v2.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This header file is the same for FSP v1 and v2, although there may be
some additions to come. Move it into the generic fsp directory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This header file is the same for FSP v1 and v2. Move it into the general
fsp directory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: move rename of fsp_infoheader.h from previous patch to this one]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This header file is the same for FSP v1 and v2. Move it into the general
fsp directory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: remove inclusion of fsp_hob.h in fsp_support.h]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This header file is the same for FSP v1 and v2. Move it into the general
fsp directory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This header file is the same for FSP v1 and v2. Move it into the general
fsp directory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This header file is different for each version of FSP. Move it into the
fsp_arch.h header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
At present fsp_support.h includes fsp_vpd.h which is an FPSv1 concept
(VPD means Vital Product Data). For FSPv2 only UPD (Updatable Product
Data) is used.
To avoid mangling header files, put these two includes in a separate
header which we can adjust as necessary for FSPv2.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This header file is the same for FSP v1 and v2. Move it into the general
fsp directory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: remove forward declarations in fsp_support.h]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Since there is now a new version of the FSP and it is incompatible with
the existing version, move the code into an fsp1 directory. This will
allow us to put FSP v2 code into an fsp2 directory.
Add a Kconfig which defines which version is in use.
Some of the code in this new fsp1/ directory is generic across both FSPv1
and FSPv2. Future patches will address this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
The commit
642b80d256 ("net: designware: drop compatible altr, socfpga-stmmac")
breaks designware ethernet for all ARC boards. It removes
"altr, socfpga-stmmac" compatible from "drivers/net/designware.c"
without changing compatible in the boards which use it.
Fix that by adding "snps,arc-dwmac-3.70a" compatible string to
"drivers/net/designware.c" and using it in ARC boards device tree.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
This reverts commit 0797f7f0b7.
Tegra specific solution is not required any more as efi core has been
made aware of ram_top with the following commit:
7b78d6438a efi_loader: Reserve unaccessible memory
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
The SPL device tree is missing the entires for gpio1, uart1, usdhc1 and
usdhc2. This creates the missing imx6q-logicpd-u-boot.dtsi file
which will enable these functions so SPL can properly setup UART, detect
microSD card, and startup.
Fixes: 8f4691e31a ("ARM: imx6q_logic: With SPL_OF_CONTROL enabled,
remove MMC init")
Signed-off-by: Adam Ford <aford173@gmail.com>
On HS devices the access to TRNG is restricted on the non-secure
ARM side, disable the node in DT to prevent firewall violations.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The memory allocated to store the FIT image containing SYSFW and board
configuration data is statically defined to the largest size expected.
This was 269000 bytes but now needs to be grown to 276000 to make room
for the signatures attached to the board configuration data on High
Security devices.
Signed-off-by: Andrew F. Davis <afd@ti.com>
This is reincarnation of the U-Boot
commit 3469bf4274
Author: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Date: Wed Jan 10 19:40:15 2018 +0200
x86: zImage: Propagate acpi_rsdp_addr to kernel via boot parameters
after upstream got eventually the Linux kernel
commit e6e094e053af75cbc164e950814d3d084fb1e698
Author: Juergen Gross <jgross@suse.com>
Date: Tue Nov 20 08:25:29 2018 +0100
x86/acpi, x86/boot: Take RSDP address from boot params if available
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch restores commit c49d0ac38a ("ARM: dts: rmobile: Increase off-on
delay on the SD Vcc regulator"), which was accidentally dropped during DT
resync in commit 317d13ac63 ("ARM: dts: rmobile: Synchronize Gen3 DTs with
Linux 5.0").
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fixes: 317d13ac63 ("ARM: dts: rmobile: Synchronize Gen3 DTs with Linux 5.0")
The commit 619f002db8 ("rockchip: make_fit_atf.py: fix loadables property
set error") fixed the double-loading of the primary atf-image, but didn't
take into account that there may be rare atf images with only that main
section present.
Right now this will result in a broken its due to the loadables section not
getting closed correctly, so fix that by adapting the guards around the loop.
The guards now protect against 0 segments when the bl31 binary doesn't
contain any section and 1 segment when only a core atf section is present.
Fixes: 619f002db8 ("rockchip: make_fit_atf.py: fix loadables property set error")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Originally the cpuid var the value gets read into was defined as
u8 cpuid[RK3399_CPUID_LEN];
hence the sizeof(cpuid) would return the correct the correct number
of array elements.
With the move to a separate function cpuid becomes a pointer and
sizeof(cpuid) hence returns the pointer size - 8 in the arm64 case.
We do have the actual id length available as function param so use
it for actual amount of bytes to read.
Fixes: 0482538499 ("rockchip: rk3399: derive ethaddr from cpuid")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Tinker board needs to mux all the sdmmc gpio and
activate the regulator connected to bank 7. Remove
all the bank that are not in use and mark them as dm,spl
so-that it would initialize at SPL.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
newline \n was missed in fdt_path_offset, error loop.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
ROCKCHIP_BROM_HELPER is selected as if TPL/SPL ROCKCHIP_BACK_TO_BROM
has been defined, so drop the explicit enablement for vyasa board.
This change is supposed to missed during config move to
other locations, and missed to drop the same.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Add missing PCI range for translating DRAM to bus addresses.
This fixes e.g. PCI NIC interface and allows network to work
in QEMU.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Pass -m4 instead of -m4-nofpu to GCC versions which do not support
the -m4-nofpu option.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since binutils 2.30 , the resulting U-Boot binary was incorrectly linked
against address 0 instead of text base, fix it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
According to the latest am572x[1] and dra74x[2] data manuals, mmc3
default, hs, sdr12 and sdr25 modes use iodelay values given in
MMC3_MANUAL1. Set the MODE_SELECT bit for these so that manual mode is
selected and correct iodelay values are configured.
[1] http://www.ti.com/lit/ds/symlink/am5728.pdf
[2] http://www.ti.com/lit/ds/symlink/dra746.pdf
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
API get_ti_sci_handle() is relying on the device-tree node name
to be "dmsc" for probing the ti_sci device. But with the introduction
of debug messages for dmsc, the node name changed to dmsc@44083000.
Because of this ti_sci is never probed cause a boot failure. Instead
of relying on device-tree node name, use the first available firmware
node for probing ti_sci.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The da8xx GPIO driver is available with DM_GPIO support. This
patch enables the CMD_GPIO, CMD_DM, and DM_GPIO and DA8XX_GPIO.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add device tree from Linux for driver model conversion
and enable OF_CONTROL. This will remove the following compile
warning:
==================================================
Device Tree Source is not correctly specified.
Please define 'CONFIG_DEFAULT_DEVICE_TREE'
or build with 'DEVICE_TREE=<device_tree>' argument
===================================================
Target was compile tested, build was clean.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
In SerDes protocol 0x13BB, lane C was erroneously assigned
to PCIE1, this is now updated to PCIE2
Fixes: 36f50b7523 ("armv8: ls1028a: Add other serdes
protocal support")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The correct config entry is CONFIG_PCIE_LAYERSCAPE and this
typo results in skipping the fixup of Linux PCIe DT nodes.
Also enable the fixup when Layerscape Gen4 controller driver
is enabled.
Fixes: 4da0e52c9d (armv8: fsl-layerscape: fix config dependency
for layerscape pci code)
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
By default, i2c input clock is programmed at
platform clk / 2 in u-boot, but this is not
correct for all the platforms,
Update I2C clock divider's default values as per
SoC (LS1012A, LS1028A, LX2160A and LS1088A).
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The SP805-WDT module on LS1028A requires configuration of PMU's
PCTBENR register to enable watchdog counter decrement and reset
signal generation. The watchdog clock needs to be enabled first.
Signed-off-by: Thomas Schaefer <thomas.schaefer@kontron.com>
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the device-tree structure describing the MUX in board dts.
QDS board has an on-board RGMII PHY and 4 slots for extension cards.
All these can be accessed over MDIO through a MDIO MUX controlled
over I2C.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Use obj-$(config) instead of #ifdef $config to make the code looks
clean, and move the misc_init for U-Boot proper only.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The rk3188/Makefile already depends on !TPL_BUILD, so no need to add
this again in parent Makefile, remove it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
For sake of consistency use spaces over TABs in ASL code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Intel iDMA 32-bit controller has 17 bits for the maximum block size value.
Due to nature of the binary number representation the maximum value is
2^17 - 1. The original code misses the latter part in equation.
Fixes: 5e99fde34a ("x86: tangier: Populate CSRT for shared DMA controller")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Per PCI firmware specification the ACPI has to reserve the memory
which is defined as PCI ECAM.
Fixes: 39665beed6 ("x86: tangier: Enable ACPI support for Intel Tangier")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
GCC 9.2 starts complaining about possible pointer misalignment of
pointers to the unpacked (alignment=4) structures in the packed
(alignment=1) ones:
CC arch/x86/cpu/tangier/acpi.o
arch/x86/cpu/tangier/acpi.c: In function ‘acpi_create_fadt’:
arch/x86/cpu/tangier/acpi.c:22:37: warning: taking address of packed
member of ‘struct acpi_fadt’ may result in an unaligned pointer value
[-Waddress-of-packed-member]
22 | struct acpi_table_header *header = &(fadt->header);
CC arch/x86/lib/acpi_table.o
arch/x86/lib/acpi_table.c: In function ‘acpi_create_spcr’:
arch/x86/lib/acpi_table.c:366:37: warning: taking address of packed
member of ‘struct acpi_spcr’ may result in an unaligned pointer value
[-Waddress-of-packed-member]
366 | struct acpi_table_header *header = &(spcr->header);
Fix the potential issues by annotating embedded structures with
__packed even though they are packed naturally.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add GCC version number in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Use efi_add_conventional_memory_map() to configure EFI conventional memory
properly with ram_top value. This will give 32-bit mode U-Boot proper
conventional memory regions even if e820 has an entry which is greater than
32-bit address space.
Signed-off-by: Aiden Park <aiden.park@intel.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[bmeng: fixed some typos in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
If a crash occurs, show the loaded UEFI images to facilitate analysis.
This is an example output:
=> bootefi 0x1000000
Found 0 disks
Hello world of bugs!
Invalid Opcode (Undefined Opcode)
EIP: 0010:[<06ceb06e>] EFLAGS: 00010206
Original EIP :[<fec9906e>]
EAX: 00000000 EBX: 06cec000 ECX: 00000fd0 EDX: 00000001
ESI: 06ced18a EDI: 07d0fe10 EBP: 07fe27a0 ESP: 07d0fde0
DS: 0018 ES: 0018 FS: 0020 GS: 0018 SS: 0018
CR0: 00000033 CR2: 00000000 CR3: 00000000 CR4: 00000000
DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
DR6: ffff0ff0 DR7: 00000400
Stack:
0x07d0fde8 : 0x00000000
0x07d0fde4 : 0x06ced040
--->0x07d0fde0 : 0x07fe27a0
0x07d0fddc : 0x00010206
0x07d0fdd8 : 0x00000010
0x07d0fdd4 : 0x06ceb06e
UEFI image [0x06cea000:0x06cf0fff] pc=0x106e '/bug-i386.efi'
### ERROR ### Please RESET the board ###
With the additional information provided by this patch we know that the
problem occurred 0x106e after the load address of bug-i386.efi.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Now that we are able to get the size of high memory from QEMU,
report its memory range as usable ram.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Aiden Park <aiden.park@intel.com>
At present only size of memory that is below 4GiB is retrieved from
QEMU. Add a function that gets size of memory that is above 4GiB.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Aiden Park <aiden.park@intel.com>
This extracts getting memory size logic in dram_init() to a separate
routine qemu_get_low_memory_size(). No functional changes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Aiden Park <aiden.park@intel.com>
Every x86 platform provides board_get_usable_ram_top(), hence there
is no need to provide a weak version board_get_usable_ram_top(), not
to mention there is another weak version board_get_usable_ram_top()
in common/board_f.c.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Aiden Park <aiden.park@intel.com>
Using ACPI predefined macros, such as Zero or One, will reduce a binary
size of resulting ACPI tables.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: manually fixed the conflicts when applying]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
- fix bcm2835_sdhost to wait long enough for a transfer to complete
- increase kernel image size from 8 MB to 64 MB on arm64
- add support for RPi4
- add prefixes for raspberry pi related stuff to git-mailrc
-----BEGIN PGP SIGNATURE-----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=hWTf
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2019.10' of https://github.com/mbgg/u-boot
- fix mailbox status register used for polling
- fix bcm2835_sdhost to wait long enough for a transfer to complete
- increase kernel image size from 8 MB to 64 MB on arm64
- add support for RPi4
- add prefixes for raspberry pi related stuff to git-mailrc
This clock has a different mbox ID so have this included in the relevant
header file.
Signed-off-by: Andrei Gherzan <andrei@balena.io>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Define two target configs for Raspberry Pi 4 (32 and 64bit) and the
corresponding BCM2838* configs.
Be aware of the current limitation in firmware which requires an
explicit configuration to force the arm in 64bit mode when the
respective target is used.
Signed-off-by: Andrei Gherzan <andrei@balena.io>
[mb: rename BCM2838 -> BCM2711]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Devices of bcm283x have different base address, depending if they are on
bcm2835 or bcm2836/7. Use BCM283x_BASE depending on the SoC you want to
build and only add the offset in the header files.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Andrei Gherzan <andrei@balena.io>
Before we can send a message to the mailbox we have to check that there
is space to do so. Therefore we poll the status register. But up to now
the wrong status register, the one of mailbox 0, was checked. Fix this
by polling the status regiser of mailbox 1.
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
[mb: rename registers and update commit message]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Add nodes for the Aspeed SD controllers with their necessary properties.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Implicitly Marvell MDIO driver uses DT node names for devices, but in this
case that is not unique. Set MDIO device names for master/slave to
cpm/cps.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Create drivers/net/fsl-mc/Kconfig and move fsl-mc specific configs
from arch/arm/cpu/armv8/fsl-layerscape/Kconfig to this new Kconfig
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
These are some very late changes mostly required to get 64-bit
division working on ARC boards.
For that we had to import missing parts of libgcc and add compiler
flags to EMSDP which otherwise used very simple profile for compliation.
And while at it another fix for EM SDP initialization is inluded as well.
As reported by Kever here [1] we were unable to compile 64-bit division
code due to missing definition of __udivdi3().
Import its implementation and __udivmoddi4() as its direct dependency
from today's libgcc [2].
[1] https://patchwork.ozlabs.org/patch/1146845/
[2] 5d8723600b
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
