J721e SoM as a 64MB HyperFlash on board. Add pinmux and DT node for the
same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add DT node for HyperBus Memory Controller in the FSS. On J721e, its not
possible to use OSPI0 and HBMC simultaneously as they are muxed within
the Flash Subsystem hence disable HBMC by default as keep OSPI enabled.
Bootloader will fixup DT when it detects HyperFlash instead of OSPI.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
To allow OCRAM to be used as wakeup source in
deep sleep, do not power it down.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The patch adds an errata ID A-008646 for workaround
to provide more information by errata ID.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
LX2160A/LX2120A/LX2080A SVR value should be
0x873600/0x873620/0x873602
Previous values were valid only if CAN fuse is blown.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
ls1028a has 4 personalities: ls1028a, ls1027a, ls1017a and ls1018a.
Both ls1027a and ls1017a personalities are lower functionality version
which doesn't support the multimedia subsystems, like LCD, GPU.
To disable multimedia feature on non-multimedia version,
set the status property to disabled in dts nodes.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Program register bit of SCFG_SNPCNFGCR_USBxRDSNP and
SCFG_SNPCNFGCR_USBxWRSNP(x = 1, 2, 3) to drive USBx read/write
snoop signal on LS1043A and LS1046A.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add LS1027A, LS1018A and LS1017A personalities support to
LS1028A SoC family.
LS1028A is the prime personality of LS1028A SoC family.
LS1027A is a lower funtionality version of QorIQ LS1028A
which does not support the multimedia subsystems, such as LCD
controller, GPU, and eDP PHY.
The QorIQ LS1018A and LS1017A SoCs are single 64-bit Arm A72
core, low power versions of the QorIQ LS1028A and LS1027A
SoCs respectively.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
- add HDMI/CVBS display support for Amlogic G12A SoCs and SEI510 board
- add support for Amlogic A311D based Khadas VIM3
- add support for Amlogic S905X3 based SEI610 board, targeting Android support like SEI510
-----BEGIN PGP SIGNATURE-----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=g/kq
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20191018' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- document alternative libretech-cc installation methods, including upstream TF-A and opensource tools
- add HDMI/CVBS display support for Amlogic G12A SoCs and SEI510 board
- add support for Amlogic A311D based Khadas VIM3
- add support for Amlogic S905X3 based SEI610 board, targeting Android support like SEI510
Rename meson-g12a-u-boot.dtsi into meson-g12-common-u-boot.dtsi to
match the new DT architecture and add meson-sm1-sei610-u-boot.dtsi
to handle the U-Boot specific DT for graphics.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Values imported from Linux driver, but in correct numeric order.
Khadas VIM3 prints: Amlogic Meson G12B (A311D) Revision 29:b (10:2)
Cc: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Write SoC instead of Soc. The Linux driver is not affected.
Fixes: f41d723b9f ("ARM: meson: display Amlogic SoC Information")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
In Linux meson-g12-common.dtsi was introduced as well as new g12b nodes
and headers, as dependencies of new meson-g12b-a311d-khadas-vim3.dts.
Copied from da0c9ea146cb ("Linux 5.4-rc2")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Like the meson-gx support, add the U-Boot specific bits in DT
to support graphics on G12A SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
If VIDEO_MESON is enabled, we need to setup the fdt for the framebuffer.
Call meson_vpu_rsv_fb() which reserves the framebuffer memory region for
EFI, and sets up simple-framebuffer nodes if simplefb support is
enabled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
The released Linux boot image header in v5.3 is different from the
one present in U-Boot. Align the header with the new version. The
changes in Linux are backward compatible. Previous U-Boot releases
with older header will continue to work as well. As v5.3 kernel is
the first one to support image header, there is no compatibility
issue between new U-Boot (with this patch) and older kernel.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This patch adds a DM based driver model for gpio controller present in
FU540-C000 SoC on HiFive Unleashed A00 board. This SoC has one GPIO
bank and 16 GPIO lines in total, out of which GPIO0 to GPIO9 and
GPIO15 are routed to the J1 header on the board.
This implementation is ported from linux based gpio driver submitted
for review by Wesley W. Terpstra <wesley@sifive.com> and/or Atish Patra
<atish.patra@wdc.com> (many thanks !!). The linux driver can be referred
here [1]
[1]: https://lkml.org/lkml/2018/10/9/1103
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Dropping some test Elf files and building them from source instead
- Refactoring of x86 16-bit entries
- Support for SPL symbols within sections
- Handle the 'notes' sections and hidden symbols in recent binutils
- Improved error reporting with a tool fails
libfdt and documentation fixes
vboot required-key test
driver model power-domain controls
patman Message-Id enhancement
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl2l20YACgkQfxc6PpAI
reZQQQgA0zxySnZR6IuTr+MXJP019SjU0T/rj2Ob77ODhLTtLtE3aFYgBIsyyOyr
/NZ6V7wPhCfGGBGWdPzYdOUIkG5L4O+1zrwWGgVJCAAaCaDlJVIXmljJ667SE9ps
9jfJW/nkzgsa/cOweOUJF3vBUKnDN1pv9aTXwAXttzv/OqaZ1AaUObnmeZ9fzr65
mXjR7/eLYx26KQ8IEo8hhgdFhN/d/aUtSCYPWASqtcI9TLg8A5gmtNxy83+w8gzC
kFIr7c0QjZ3EQHLyD4/MAcGvhZZMBPbV6dyIO19hUS80S1l1yMTd72iTYuvG8bAt
5TzlQCSqvGryF6TRxVn8GPr2/T0v/A==
=Oo/D
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-15oct19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
binman enhancements:
- Dropping some test Elf files and building them from source instead
- Refactoring of x86 16-bit entries
- Support for SPL symbols within sections
- Handle the 'notes' sections and hidden symbols in recent binutils
- Improved error reporting with a tool fails
libfdt and documentation fixes
vboot required-key test
driver model power-domain controls
patman Message-Id enhancement
U-Boot cannot be built for h2200_defconfig with CONFIG_DM=y.
The maintainer Lukasz Dalek suggested to remove the board.
https://lists.denx.de/pipermail/u-boot/2019-August/380685.html
Cc: Lukasz Dalek <luk0104@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[trini: As this is the last non-toradex PXA board, update travis too]
Signed-off-by: Tom Rini <trini@konsulko.com>
Without this patch, compiling may potentially fail.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
When I tried to run some new efi tests with pytest, efi_smbios_register()
triggered a segmentation fault. Here is the location where it happened:
efi_init_obj_list()
efi_smbios_register()
write_smbios_table()
smbios_write_type4()
smbios_write_type4_dm()
where dev_get_parent_platdata() should return a pointer to struct
cpu_platdata, but it is actually NULL because any cpu device on
sandbox is attached to "root_driver."
With this patch, this issue will be fixed by moving all the definitions
of cpus under "cpus" node so that they have a "cpu_bus" parent.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present these two sections of code are linked together into a single
2KB chunk in a single file. Some Intel SoCs like to have a FIT (Firmware
Interface Table) in the ROM and the pointer for this needs to go at
0xffffffc0 which is in the middle of these two sections.
Make use of the new 'reset' entry and change the existing 16-bit entry to
include just the 16-bit data.
Signed-off-by: Simon Glass <sjg@chromium.org>
-------------------
Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/597498628
- logicpd pinmux
- i.MX7ULP: imx_ddr_size
- fixes Toradex i.MX6/i.MX7
- pico-imx7d
- tpc70 converted to DM
- New Board: meerkat96
- add HAB version command
- i.MX8 :
imx8: Jump from alias to OCRAM address at SPL init
imx8qm/qxp: Set SPL TEXT base to OCRAM base
-----BEGIN PGP SIGNATURE-----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=J8jd
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191014' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20191014
-------------------
Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/597498628
- logicpd pinmux
- i.MX7ULP: imx_ddr_size
- fixes Toradex i.MX6/i.MX7
- pico-imx7d
- tpc70 converted to DM
- New Board: meerkat96
- add HAB version command
- i.MX8 :
imx8: Jump from alias to OCRAM address at SPL init
imx8qm/qxp: Set SPL TEXT base to OCRAM base
- Add sdhci driver for Broadcom iProc platform
- Add a driver callback for power-cycle for mmc
- Implement host_power_cycle callback for stm32_sdmmc2
- spl: dm_mmc: Initialize only the required mmc device
THe RVT data includes a major and minor version in its header
parameter. Add a new command to print this out.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
i.MX7ULP uses the same MMDC controller IP as found on i.MX53
and i.MX6, so build mmdc_size.c for i.MX7ULP as well.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The original imx_ddr_size() implementation had some
issues reported by checkpatch like this:
CHECK: Prefer kernel type 'u32' over 'uint32_t'
#127: FILE: arch/arm/mach-imx/mmdc_size.c:16:
+ uint32_t ctl;
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
#151: FILE: arch/arm/mach-imx/mmdc_size.c:40:
+ unsigned ctl = readl(&mem->ctl);
Fix all of them.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Place imx_ddr_size() into a separate file.
The motivation for doing this is to be able to easily reuse
imx_ddr_size() on i.MX7ULP.
Currently imx_ddr_size() is inside arch/arm/mach-imx/cpu.c, which
is not built for i.MX7ULP.
Changing the logic to allow building cpu.c for i.MX7UP would
require adding several ifdef's, leading to a not a very elegant
solution.
To allow better reuse, just place imx_ddr_size() into a common
mmdc_size.c file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
The new class dsi host allows the management of the bridge DPI to DSI.
This bridge is embedded in the chipset mp1 (come from synopsys company).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
The new class dsi host allows the management of the bridge DPI to DSI.
This bridge is embedded in the chipset mp1 (come from synopsys company).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Display Serial Interface (DSI) host can usefully be modelled
as their own uclass.
DSI defines a serial bus and a communication protocol
between the host and the device (panel, bridge).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
When running SPL on iMX8, the A core starts at address 0
which is a alias to OCRAM 0x100000.
The alias only map first 96KB of OCRAM, so this require the
SPL size can't beyond 96KB. But when using SPL DM, the size increase
significantly and may exceed 96KB.
So to fix the problem, we will change SPL linker address to OCRAM
address 0x100000. And then jump to the absolute address not the PC relative
address for entering OCRAM.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This patch converts the TPC70 to use driver model and device tree
description in both SPL and u-boot proper.
Notable changes (DM/DTS conversion):
- PINCTRL{_IMX6}
- DM_I2C
- enable 'regulator' and 'pmic' commands
- DM_MMC and BLK (USDHC)
- DM_ETH
- DM WDT (including SYSRESET)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit adds new file - imx6q-kp-u-boot.dtsi with a set of u-boot
specific properties for imx6q KP device.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
With the 256KB of OCRAM available to SPL now, there should be
enough room to enable the pinmuxing in SPL from the device tree.
This patch enables SPL_PINCTRL et al and adds the serial and
usdhc pin mux references to the -u-boot.dtsi file so the pins can be
configured from the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of
96Boards community and complies with all Consumer Edition board
specifications.
https://www.novtech.com/products/meerkat96.htmlhttps://www.96boards.org/product/imx7-96/
The initial supported/tested devices include:
- Debug serial
- SD
- USB Host (with Ethernet)
With these support, it's good enough for loading Linux Kernel from SD or
Ethernet over USB.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
