The current mpc83xx_clk driver is broken for any board for which
mpc83xx_has_pci() is true, i.e. anything not MPC8308:
When is_clk_valid() reports that MPC83XX_CLK_PCI is valid,
init_all_clks() proceeds to call init_single_clk(), but that doesn't
know about either MPC83XX_CLK_PCI or has any handling of the
TYPE_SCCR_ONOFF mode correctly returned by retrieve_mode(). Hence
init_single_clk() ends up returning -EINVAL, and the whole board hangs
in serial_init().
The quickest fix is to simply pretend that clock is invalid for
all, since nobody can have been relying on it. Adding proper support
seems to be a bit more involved than just handling TYPE_SCCR_ONOFF:
- The power-on-reset value of SCCR[PCICM] is 0, so
mpc83xx_clk_enable() would probably need to be tought to enable the
clock.
- The frequency of PCI_SYNC_OUT is either SYS_CLK_IN or SYS_CLK_IN/2
depending on the CFG_CLKIN_DIV configuration input, but that can't
be read from software, so to properly fill out
->speed[MPC83XX_CLK_PCI] I think one would need guidance from
Kconfig or dtb.
Partially fixes: 07d538d281 clk: Add MPC83xx clock driver
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Mario Six <mario.six@gdsys.cc>
This adds a message to lists_bind_fdt when it skips initializing a device
pre-relocation. I've had a couple errors where a device didn't initialize
properly because one of its dependencies was missing.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present we only support two phases where devres can be used:
bind and probe. This is handled with a boolean. We want to add a new
phase (platdata), so change this to an enum.
Signed-off-by: Simon Glass <sjg@chromium.org>
The devres functionality has very few users in U-Boot, but it still should
have tests. Add a few basic tests of the main functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present when CONFIG_DEBUG_DEVRES is enabled, U-Boot prints log messages
to the console with every devres allocation/free event. This causes most
tests to fail since the console output is not as expected.
In particular this prevents us from adding a device to sandbox which uses
devres in its bind method.
Move devres over to use U-Boot's logging feature instead, and add a new
category for devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to avoid allocating platform data twice. This could happen if
device_probe() is called after device_ofdata_to_platdata() for the same
device.
Add a flag to track whether device_ofdata_to_platdata() has been called on
a device. Check the flag to make sure it doesn't happen twice, and clear
the flag when the data is freed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new internal function, device_ofdata_to_platdata() to handle
allocating private space associated with each device and reading the
platform data from the device tree.
Call this new function from device_probe().
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the parent is probed before the child's ofdata_to_platdata()
method is called. Adjust the logic slightly so that probing parents is
not done until afterwards.
Signed-off-by: Simon Glass <sjg@chromium.org>
This method is supposed to extract platform data from the device tree. It
should be done before the device itself is probed. Move it earlier in the
device_probe() function.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the clock driver reads its ofdata in the probe() method. This
is not correct although it is often harmless.
However in this case it causes a problem, something like this:
- ast_get_scu() is called (from somewhere) to get the SCI address
- this probes the clock
- first sets up ofdata (which does nothing at present)
- DM marks clock device as active
- DM calls pinctrl
- pinctrl probes and calls ast_get_scu() in ast2500_pinctrl_probe()
- ast_get_scu() probes the clock, but sees it already marked as
probed
- ast_get_scu() accesses the clock's private data, with scu as NULL
- DM calls clock probe function ast2500_clk_probe() which reads scu
By putting the read of scu into the correct method, scu is read as part of
ofdata setup, and everything is OK.
Note: This problem did not matter until now since DM always probed all
parents before reading a child's ofdata. The fact that pinctrl is a child
of clock seems to trigger this strange bug.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
It is not possible to access a device on a PCI bus that has not yet been
probed, since the bus number is not known. Add a warning to catch this
error.
Signed-off-by: Simon Glass <sjg@chromium.org>
These macros use __FILE__ which inserts the full path of the object file
into U-Boot, thus increasing file size. Drop these usages.
An older version of this patch was submitted here:
http://patchwork.ozlabs.org/patch/1205784/
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a driver for the virtio-rng device on the qemu platform. The
device uses pci as a transport medium. The driver can be enabled with
the following configs
CONFIG_VIRTIO
CONFIG_DM_RNG
CONFIG_VIRTIO_PCI
CONFIG_VIRTIO_RNG
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Add a sandbox driver for random number generation. Mostly aimed at
providing a unit test for rng uclass.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a driver for the rng device found on stm32mp1 platforms. The
driver provides a routine for reading the random number seed from the
hardware device.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Remove a superfluous blank line
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add an entry for allowing clock enablement for the random number
generator peripheral, RNG1.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Add a uclass for reading a random number seed from a random number
generator device.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Load the optional resource table from the firmware, and write its
address in the dedicated backup register.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Update the dedicated backup register to track the coprocessor state and
rely on that register to compute the .is_running() value (which expects
a return value of 0 -not 1- if the processor is running).
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Add rproc_elf_load_rsc_table(), which searches for a resource table in
an elf64/elf32 image, and if found, copies it to device memory.
Add also the elf32 and elf64 variants of this API.
Add a test for this.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This function will be used by the SPL to get the names of images to load
from the FIT. This allows to load different images based on runtime HW
detection.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make the board driver available in the SPL too. The board driver is a way
to provide useful information about the board and that can be useful in
the SPL too.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeFDfVAAoJEB6zHgIOrC/IKfsH/2cUfXuc9IgA7L90L3g7htlS
zLAQSC8Xk0WbgbmBJh/lq6zFWj2Mu2yfkZqRzwN8bHkmOPq40F+pEAszVtjH77HM
FpSjMSDVWfNXuhmoiS571dehA0TGi1b2kknrAXqpOwVuMRncMCwaPi8yZYZSGlSV
VzMtguQxD0sZg4oMZVde3tCd41smPTPNDjzLZnXdLa0b09+EtW6enGuk3vzXlS/8
QUT68wUzkeoptJhf3pQ3BXNvkFwdNdYJ74uevDmkAYtvxyl10WNykcwYmH50Q9qq
9plF11EizmTHlj16rWpZLx66RP0s4pziKaeGMr6S8uln33Cr9N496wPqtuDBnvA=
=FYPj
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features for 2020.04 cycle
This feature set is a patch series from Tudor Ambarus which includes
parsing of the spi flash SFDP parser for SST flashes, and using those
tables to retrieve unique saved per device MAC address. This is then
used as base mac address on the SAMA5D2 Wireless SOM EK board.
The ECC registers in the SDRAM HMC Adapter should always
be accessible (both when ECC is enabled and disabled).
Currently, the registers are accessible only when ECC is enabled.
The ECC Enabled bit is used to determine the status of
ECC by later OSes so always allow access.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Enable TCU access through the Stratix10 CCU so that the
SMMU can access the SDRAM.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add SDRAM driver for Agilex SoC.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Restructure Stratix 10 SDRAM driver. Move common code to separate
file, in preparation to support SDRAM driver for Agilex.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add Cache Coherency Unit (CCU) driver.
CCU is to ensures consistency of shared data between multi masters
in the system.
Driver initializes CCU's directories and coherency agent
interfaces in CCU IP.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add clock manager driver for Agilex. Provides clock initialization
and get_rate functions.
agilex-clock.h is from Linux commit ID cd2e1ad12247.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Move Stratix10 and Agilex system manager common code to
system_manager_soc64.h. Changed macros to use SYSMGR_SOC64_*.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Move firewall related code to new firewall.c, to share
code in Stratix 10 and Agilex.
SDMMC will transfer data to OCRAM in SPL. So, enable privilege for SDMMC
to allow DMA transfer to OCRAM.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Convert clock manager for Gen5, Arria 10 and Stratix 10 from struct
to defines.
Change to get clock manager base address from DT node instead of using
#define.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Convert system manager for Gen5, Arria 10 and Stratix 10 from struct
to defines.
Change to get system manager base address from DT node instead of
using #define.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Convert reset manager for Gen5, Arria 10 and Stratix 10 from struct
to defines.
Change to get reset manager base address from DT node instead of using
#define.
spl_early_init() initializes the DT setup. So, move spl_early_init() to
beginning of function and before get base address from DT.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add an option for building cache drivers in SPL.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
When the `dfu` command is called from the U-Boot environment,
it now accepts an optional parameter that specifies a timeout (in seconds).
If a DFU connection is not made within that time the `dfu` command exits
(as it would if Ctrl+C was pressed). If the timeout is left empty or being
zero the `dfu` command behaves as it does now.
This is useful for allowing U-Boot to check to see if anything wants to
upload new firmware before continuing to boot.
The patch is based on the commit
5e966ccc3c
by Sebastien Colleur, which has been heavily reworked due to U-Boot changes
in the past.
Signed-off-by: Brad Campbell <bradjc5@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
These files should not be included in meson header files. Drop them and
tidy up the affected C files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
In cases when the same SPL should run on boards with i.MX8MM, that
differ in DDR configuration, it is necessary to try different
parameters and check if the training done by the firmware suceeds or
not.
Therefore we return the DDR training/initialization success to the
upper layer in order to be able to retry with different settings if
necessary.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The driver works fine with iMX6SX, add the missing compatible string.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Bring in the following merges:
commit 8fbbec12f7
Merge: 87f69f467a63618e71e8
Author: Tom Rini <trini@konsulko.com>
Date: Fri Jan 3 09:48:47 2020 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next
- updates and fixes on ls1028a, lx2, ls1046a, MC-DPSPARSER support
commit 87f69f467a
Merge: c0912f9bbf4466b99703
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 24 08:18:19 2019 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next
- Enable DM driver on ppc/km boards
- Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x,
T104x, P4080, P2041, P2020, P1020, P3041
- Some updates in mpc85xx-ddr driver, km boards
commit c0912f9bbf
Merge: 533c9f5714a1d6dc3f84
Author: Tom Rini <trini@konsulko.com>
Date: Wed Dec 18 07:20:19 2019 -0500
Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next
- Various x86 common codes updated for TPL/SPL
- I2C designware driver updated for PCI
- ICH SPI driver updated to support Apollo Lake
- Add Intel FSP2 base support
- Intel Apollo Lake platform specific drivers support
- Add a new board Google Chromebook Coral
commit 533c9f5714
Merge: 553cb06887033e18b47b
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 17 07:53:08 2019 -0500
Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next
i2c: for next
- misc: i2c_eeprom:
Add partition support and add ability to query size
of eeprom device and partitions
- i2c common:
add support for offset overflow in to address and add
sandbox tests for it.
commit 553cb06887
Merge: f39abbbc53b4f98b3b16
Author: Tom Rini <trini@konsulko.com>
Date: Thu Dec 12 08:18:59 2019 -0500
Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next
buildman improvements including toolchain environment feature
sandbox unicode support in serial
Adam Ford reports that this change breaks booting on da850-evm and
Bartosz Golaszewski agrees that with the impending release we should
revert the change for now. With that noted:
This reverts commit 21a4d80a71.
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The scripts/Makefile.lib generates an assembler file (*.S) to wrap the
font data for each file of type ttf defined in Kconfig.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
This code does not really need to use #ifdef. We can use if() instead and
gain build coverage without impacting code size.
Change the #ifdefs to use IS_ENABLED(), etc., instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
This code does not really need to use #ifdef. We can use if() instead and
gain build coverage without impacting code size.
Change the #ifdefs to use CONFIG_IS_ENABLED() instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
This code does not really need to use #ifdef. We can use if() instead and
gain build coverage without impacting code size.
Change the #ifdefs to use IS_ENABLED() instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
This code does not really need to use #ifdef. We can use if() instead and
gain build coverage without impacting code size.
Change the #ifdefs to use IS_ENABLED() instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most x86 boards that use video make use of 32bpp graphics. Enable this by
default. This fixes missing graphics output on some x86 boards.
Also remove the unnecessary 'default n' while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
The ep node device tree name is governed by these bindings:
https://github.com/torvalds/linux/blob/master/Documentation/
devicetree/bindings/pci/layerscape-pci.txt#L24
As per above the ep compatible node contains platform name.
Therefore, define the ep node compatible as CONFIG to find the
pcie ep node in device tree during device tree fixup.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
move the PCIE related config from arch Kconfig to PCI Kconfig.
As the PCI_LAYERSCAPE driver is being used in platform other than
fsl-layerscape platforms like ls102xa.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The Rockchip SPI controller's length register only supports 16-bits,
yielding a maximum length of 64KiB (the CTRLR1 register holds "length -
1"). Trying to transfer more than that (e.g., with a large SPI flash
read) will cause the driver to hang.
Now, it seems that while theoretically we should be able to program
CTRLR1 with 0xffff, and get a 64KiB transfer, but that also seems to
cause the core to choke, so stick with a maximum of 64K - 1 bytes --
i.e., 0xffff.
Note, that the size is further divided into 'minus 1' while writing
into CTRLR1.
This change fixed two different read issues,
1. sf read failure when with > 0x10000
2. Boot from SPI flash failed during spi_flash_read call in
common/spl/spl_spi.c
Observed and Tested in
- Rockpro64 with Gigadevice flash
- ROC-RK3399-PC with Winbond flash
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Static checker warns 'ret' variable may be used uninitialized in
spi_nor_erase() and spi_nor_write() in case of zero length requests.
Fix these warnings by checking for zero length requests and returning
early.
Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Currently inside ddr_init() there is a mix of printf() and debug()
level messages.
Since this type of information is useful for debug purposes,
convert all of them to debug level for consistency.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
As per "Table 26-7. SATA PHY Subsystem Low-Level Programming Sequence"
in TRM [1] we need to turn on SATA_PHY_TX before SATA_PHY_RX.
[1] DRA75x, DRA74x TRM - http://www.ti.com/lit/ug/sprui30f/sprui30f.pdf
Signed-off-by: Roger Quadros <rogerq@ti.com>
For increased DPLL stability use the settings recommended in
the TRM [1] for PHY_RX registers for SATA and USB.
For SATA we need to use spread spectrum settings even
though we don't have spread spectrum enabled. The
suggested non-spread spectrum settings don't work.
[1] DRA75x, DRA74x TRM - http://www.ti.com/lit/ug/sprui30f/sprui30f.pdf
Signed-off-by: Roger Quadros <rogerq@ti.com>
Introduce a mode property in the driver data so that
we don't have to keep using "of_device_is_compatible()"
throughtout the driver.
No functional change.
Signed-off-by: Roger Quadros <rogerq@ti.com>
The AM572x Technical Reference Manual, SPRUHZ6H,
Revised November 2016 [1], shows recommended settings for the
SATA DPLL in Table 26-8. DPLL CLKDCOLDO Recommended Settings.
Use those settings in the driver. The TRM does not show
a value for 20MHz SYS_CLK so we use something close to the
26MHz setting.
[1] - http://www.ti.com/lit/ug/spruhz6h/spruhz6h.pdf
Signed-off-by: Roger Quadros <rogerq@ti.com>
Update API names for layerscape gen4 fixup.
Suffix layerscape_gen4 fixup API names with _ls_gen4.
This is required to organize device tree fixup in common, layerscape
and layerscape_gen4 specific code.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Suffix layerscape fixup API names with _ls.
This is required to organize device tree fixup in common,
layerscape and layerscape_gen4 specific code.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add stream_id_cur field to ls_pcie structure and initialize
it with 0 for all pcie controllers. This field will be used
for streamId calculation.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
lx2160a rev1 uses pcie_layerscape_gen4 driver and lx2160a rev2 uses
pcie_layerscape driver.
Enable pcie_layerscape code for CONFIG_PCIE_LAYERSCAPE_GEN4.
Based on SoC and revision pcie controller probe will be invoked.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for DPSPARSER object (create/destroy, open/close, apply spb)
which is required to configure Soft Parser by using MC.
Also add uboot command to apply Soft Parser Blob with command:
fsl_mc apply spb <spb_load_addr>
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Some of t1042 boards fails DDR init with an Automatic calibration error
every now and then. Investigations revealed that true Warm boots
never failed. Warm boots has some extra steps performed, one being
to start DDRC in Self Refresh and then clearing SR right after.
Applying this SR method unconditionally made all our boards
stable again, regardless of Cold/Warm boot.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
DWC3 support phy interfaces like 8/16-bit UTMI+. phy interface
initialization code would handle them properly along with UNKNOWN
type by default if none of the user/board doesn't need to use the
phy interfaces at all.
The current code is masking the 8/16-bit UTMI+ interface bits globally
which indeed effect the UNKNOWN cases, therefore it effects the platforms
which are not using phy interfaces at all.
So, handle the phy masking bits accordingly on respective interface
type cases.
Fixes: 6b7ebff001 ("usb: dwc3: Add phy interface for dwc3_uboot")
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Since, commit 62f9b65447 ("common: Move older CPU functions to their own header")
cache ops functions are declared in a separate header. Include the same
to avoid build warnings.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Passing 0 to PHY connect used to trigger a MDIO scan due to a bug fixed in
the meantime. It's unclear if bcm-sf2 wants to connect to PHY @ addr 0 or
is scanning the bus, passing -1 here should keep it functional either way.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Cc: Jiandong Zheng <jdzheng@broadcom.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
PHY address 0 is a valid PHY address, to scan for all PHYs, pass -1 to
phy_connect(). Passing 0 used to work before be accident, but does no
longer.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add gd25q128 128Mbit chip to spi-nor id table.
Tested on Pinebook Pro
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # roc-rk3399-pc
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
- Various x86 common codes updated for TPL/SPL
- I2C designware driver updated for PCI
- ICH SPI driver updated to support Apollo Lake
- Add Intel FSP2 base support
- Intel Apollo Lake platform specific drivers support
- Add a new board Google Chromebook Coral
JESD216 allow vendors to define their own SFDP tables.
Add SST SFDP parser. The vendor table is allocated using resource-managed
kmalloc - the table will be freed on driver detach. It will be accessible
by getting the UCLASS_SPI_FLASH's private data.
The SST's SFDP table is particularly of interest because contains
pre-programmed globally unique EUI-48 and EUI-64 identifiers.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Add ability to query size of eeprom device and partitions
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add support for setting the chip address offset mask to EEPROM sumulator
and add tests to test it.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Improve i2c EEPROM simulator testing by providing access functions to
check the previous chip addr and offset.
Given that we can now directly test the offsets, also simplified the
offset mapping and allow for wrapping acceses.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Some devices (2 wire eeproms for example) use some bits from the chip
address to represent the high bits of the offset instead of or as well
as using multiple bytes for the offset, effectively stealing chip
addresses on the bus.
Add a chip offset mask that can be set for any i2c chip which gets
filled with the offset overflow during offset setup.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
For Apollo Lake we need to take the I2C bus controller out of reset before
using this. Add this functionality to the driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a driver for the Apollo Lake pinctrl. This mostly makes use of the
common Intel pinctrl support.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a driver for the Apollo Lake SoC. It supports the basic operations and
can use device tree or of-platdata.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a GPIO driver which uses the pinctrl driver to access the pad
information. This driver relies on the GPIO nodes being subnodes to the
pinctrl device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Recent Intel SoCs share a pinctrl mechanism with many common elements. Add
an implementation of this core functionality, allowing SoC-specific
drivers to avoid adding common code.
As well as a pinctrl driver this provides a GPIO driver based on the same
code.
Once other SoCs use this driver we may consider moving more properties to
the device tree (e.g. the community info and pad definitions).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With of-platdata we need to create drivers for particular chips, or at
least drivers that are separate from the standard code, since C structures
are created by dtoc which are private to that driver.
To avoid duplicating the probing code, export this probe function for use
by these drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add support for Apollo Lake to the ICH driver. This involves adjusting the
mmio address and skipping setting of the bbar.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In TPL we want to reduce code size and support running with CONFIG_PCI
disabled. Add special code to handle this using a fixed BAR programmed
into the SPI on boot. Also cache the SPI flash to speed up boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add this method so that the memory-mapped location of the SPI flash can
be queried.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Apollo Lake (APL) only supports hardware sequencing. Add support for this
into the SPI driver, as an option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Intel Fast SPI interface is similar to ICH. Add of-platdata support
for this using the "intel,fast-spi" compatible string.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This incorrectly shortens read operations if there is a maximum write size
but no maximum read size. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useful to store the mmio base in platdata. It reduces the amount of
casting needed. Update the code and move the struct to the C file at the
same time, as we will need to use with of-platdata.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use debug() instead of printf() to reduce code size and change a bool
return value to the use the 'bool' type. Also drop the global data
declaration since it not actually used. Finally, set the log category.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use dev_get_driver_data() to obtain the device type. It has the same
effect and is shorter.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reduce the size of the probe function but putting this code into its own
function.
Also remove the assumption that the PCH is always a parent of the SPI
controller, as this is not the case APL platforms. Use driver model to
find the PCH instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is annoying to have some of the init code in a different part of the
file. Move ich_init_controller() to just above probe() to keep things
together.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We don't normally need this on x86 unless the size of SPI flash devices is
larger than 16MB. This can be enabled by particular SoCs as needed, since
it adds to code size.
Drop the default enabling of this option on x86.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present we have to have an xfer() method even if it does nothing. This
is not correct, so fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These drivers are not needed on all platforms. While they are small, it
is useful in TPL to drop then. Add Kconfig control to allow this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Update this uclass to support the needs of the Apollo Lake ITSS. It
supports four operations.
Move the uclass into a separate directory so that sandbox can use it too.
Add a new Kconfig to control it and enable this on x86.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a sandbox driver and PCI-device emulator for p2sb. Also add a test
which uses a simple 'adder' driver to test the p2sb functionality.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Primary-to-Sideband bus (P2SB) is used to access various peripherals
through memory-mapped I/O in a large chunk of PCI space. The space is
segmented into different channels and peripherals are accessed by
device-specific means within those channels. Devices should be added in
the device tree as subnodes of the p2sb.
This adds a uclass and enables it for sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Intel x86 SoCs have a power manager/controller which handles several
power-related aspects of the platform. Add a uclass for this, with a few
useful operations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Most of the timer-calibration methods are not needed on recent Intel CPUs
and just increase code size. Add an option to use the known-good way to
get the clock frequency in TPL. Size reduction is about 700 bytes.
Note that version 1 of this commit caused bootstage to crash since the CPU
was not identified. This is corrected by changes previously applied to
make sure that the CPU is identified before spl_init() is called, such as
39146a2e0b x86: Move CPU init to before spl_init()
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
On x86 platforms the timer is reset to 0 when the SoC is reset. Having
this as the timer base is useful since it provides an indication of how
long it takes before U-Boot is running.
When U-Boot sets the timer base to something else, time is lost and we
no-longer have an accurate account of the time since reset. This
particularly affects bootstage.
Change the default to not read the timer base, leaving it at 0. Add an
option for when U-Boot is the secondary bootloader.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present these options cannot be enabled for SPL/TPL, but this can be
useful in some cases. Add Kconfig options to allow it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Allow this driver to set up an IO address in SPL using an 'early-regs'
property. This allows SPL to use the I2C driver without having to enable
the full PCI stack.
Also split out ofdata_to_platdata in designware driver since this is more
correct, and more convenient for the new logic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Drivers are not allowed to use static data since they may be used in SPL
where BSS is not available.
It is possible that driver model may provide support for numbering devices
in the future. But for now, move this to global_data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is hacked into the driver at present. It seems better to have it as
a separate driver that uses the base driver. Create a new file and put
the X86 code into it.
Actually the Baytrail settings should really come from the device tree.
Note that 'has_max_speed' is added as well. This is currently always false
but since only Baytrail provides the config, it does not affect operation
for other devices.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Early in boot it is necessary to decode the PCI device/function values for
particular peripherals in the device tree or of-platdata. This is needed
in TPL where CONFIG_PCI is not defined.
To handle this, move pci_get_devfn() into a file that is built even when
CONFIG_PCI is not defined.
Also add a function for use by of-platdata, to convert a reg property to
a pci_dev_t.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present PCI auto-configuration happens in U-Boot both before and after
relocation. This is a waste of time and may mess up static addresses used
in board_init_f(). Adjust the code to supporting doing auto-configuration
once, after relocation, under control of a device-tree property.
This is needed for Apollo Lake for debugging the silicon-init code. Once
the UART is moved to a different MMIO address the debug UART does not work
and any debug output in Apollo Lake's arch_fsp_init_r() causes a hang.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass
is included in SPL/TPL without any control for boards. Some boards may
want to disable this to reduce code size where GPIOs are not needed in
SPL or TPL.
Add a new Kconfig option to permit this. Default it to 'y' so that
existing boards work correctly.
Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to
preserve the current behaviour. Also update the 74x164 GPIO driver since
it cannot build with SPL.
This allows us to remove the hacks in config_uncmd_spl.h and
Makefile.uncmd_spl (eventually those files should be removed).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
sandbox unicode support in serial
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl3xP/0ACgkQfxc6PpAI
reYTTAf/Uuhm4meLxXyho3zelrYZKcVtLcbQSTwwMKsfQYV/rH+Hbi7StbQSO1+K
UYt/A2O0ic0U+UiSpHv8A5n2JGzcmeJK1f6BJvyoXAhXJAxRKGQhxAAE+X/GcSi8
8gpfYEAb0Zpd+1eTBBMSWLXrFAwITbfqe45L4BcDb9BT+Dkhidr9SZQahu8xzgMa
Wf0oXUQy+HmHB6YYTUcpyUisYJV5SiuVZDqsMDJ58T/4nYKnAV2qlu647YFiWyZe
A+EeL13LbAGHibz385J5rAYb6RFM8SlWunicQnFrsYHoagfxTrrnkwF5EZdeBb1e
sCX+jNk28WbjcAN6wjDcOSKIVDQ4wQ==
=Ycht
-----END PGP SIGNATURE-----
Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next
buildman improvements including toolchain environment feature
sandbox unicode support in serial
i2c bugfixes for 2020.01
- i2c: i2c_cdns: fix write timeout on fifo boundary
fixes timout issue when writting number of bytes is multiple
of the FIFO depth.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJd77jyAAoJEB6zHgIOrC/IyYUH/iAUH4wo5qnOBiQU+MJluaiu
D8tMiJH13eW4gWnAqdGrOE9Q763asHIMshQpLK+4eXe4f4mZQ7re4CRNcYJrULeY
2StsJzl4sn/H4P5EiRuUWjkB7wnGRDD6ArH3j1uMJN4lpwCB0ZbqMQZpjt3wI2H4
KuE42d/ll08Aj0AvwdusffLIxlw5M1Z94uQSHoC3UTkPYN4VD5zXgdxv5eH6PZWe
paWmHQ0g7fL4UnYGWa0Jpx10SZpcut06dTeVGpsGiEOhaJHvpjYd4JAs/TTUxhFx
d5ZRjo1fStYmBXQIblhPNlJQkW4cqa/B+81f5aZbN/1yCijJWS2G8anGtY2ikPs=
=f0dF
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2020.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
- First set of u-boot-atmel fixes for 2020.01 cycle:
This set includes a small fix for gpio bank names, one for removing
unused headers (also touches some other boards), and a fix for the QSPI
env read on one of the boards.
This fixes an issue that would cause I2C writes to timeout when the
number of bytes is a multiple of the FIFO depth (i.e. 16 bytes).
Within the transfer loop, after writing the data register with a new
byte to transfer, if the transfer size equals the FIFO depth, the loop
pauses until the INTERRUPT_COMP bit asserts to indicate data has been
sent. This same check is performed after the loop as well to ensure data
has been transferred prior to returning.
In the case where the amount of data to be written is a multiple of the
FIFO depth, the transfer loop would wait for the INTERRUPT_COMP bit to
assert after writing the final byte, and then wait for this bit to
assert once more. However, since the transfer has finished at this
point, no new data has been written to the data register, and hence
INTERRUPT_COMP will never assert.
Fix this by only waiting for INTERRUPT_COMP in the transfer loop if
there's still data to be written.
Signed-off-by: Michael Auchter <michael.auchter@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Chromium EC commands can be up to 16-bits, so using a uint8_t here can
cause truncation. Update to use a uint instead.
It looks like this should likely have been done as a part of
9fea76f5d3, but this function was skipped
for some reason.
Signed-off-by: Michael Auchter <michael.auchter@ni.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
bigger than the framebuffer resolution
- reduce dead code in video and console uclass routines
(tested on mx53cx9020, sama5d2_xplained, stm32mp157c-ev1,
stm32f746-disco, stm32f769-disco and wandboard)
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXe//LA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXOqBAJ9N6oTID0v092duxoUoO5xAeqIKxgCfS/YvgGx4
KGgiPWQv0V1bGxXyYNA=
=PoNP
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-2020.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- fix crash and board reset when drawing RLE8 bitmaps
bigger than the framebuffer resolution
- reduce dead code in video and console uclass routines
(tested on mx53cx9020, sama5d2_xplained, stm32mp157c-ev1,
stm32f746-disco, stm32f769-disco and wandboard)
Due to a conversion error the sandbox does not accept byte values 0x80-0xff
from the keyboard. The UEFI extended text input unit test requires Unicode
support.
Use unsigned char for the serial buffer.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
- Increase stack size to avoid a stack overflow during distro boot.
- Add hifive-unleashed-a00.dts for SIFIVE FU540.
- Add OF_SEPARATE support for SIFIVE FU540.
- Add SPL support for Andes AX25 AE350.
- Improve U-Boot SPL / OpenSBI smp boot flow for RISC-V.
When ax25-ae350 try to enable v5l2 cache
driver in SPL configuration, it need this
option for cache support in SPL.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: KC Lin <kclin@andestech.com>
Cc: Alan Kao <alankao@andestech.com>
Get flow ID information for RX DMA channel using dma_get_cfg() interface
instead of reading from DT. This is required in order to avoid DT update
whenever there is change in the range of flow ID allocated to the host.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Implement dma_get_cfg() interface to pass flow id information for DMA
clients to use. This is needed because on K3 SoCs, CPSW (ethernet) and
UDMA (DMA provider) support "flows" within a given RX DMA channel. This
allows different network packets to be segregated while using same RX
DMA channel. In order for basic ethernet to work, CPSW slave must be
aware of the flow ID allocated for the RX channel by the DMA driver.
This interface allows CPSW to query flow ID from DMA provider and
configure it in CPSW HW.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Sometimes, there would be a need to exchange data between DMA provider
and DMA client which are very specific to DMA driver of the SoC/platform
and are not generic enough to be put into struct dma. Therefore, introduce
dma_get_cfg() interface to get DMA provider specific data from client
device. Clients can use unique configuration ID flags to get different
configuration data from DMA driver.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Fixes: e766849713 ("net: ftgmac100: convert the RX/TX descriptor arrays")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This bus is used to access internal SoC PHYs. These PHYs are configured
by the ENETC driver directly, but it's useful to have command line access
to this MDIO to debug the system especially when using new external PHYs.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On some boards MDIO may get stuck if it detects echo on the line. This is
a know hardware issue, there is a board fix for it. In case we're running
on a board that doesn't have the fix, we don't want to loop here forever
and freeze U-Boot.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This reduces the time needed to establish a link as we don't reset the link
each time the interface is used. Our Link capabilities do not change at
run-time so there is no need to re-apply PHY configuration each time.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The original code enabled link speeds up to 1Gbps, but the interface can
go up to 2.5G, enable that speed to in PHY AN mask.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Uses the new dm_eth_phy_connect helper to connect to the PHY to simplify
the code.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In some cases the link on the system interface of the aquantia PHY comes up
after the link on line interface. The link state loop only checks the line
side, which may result in first packet sent being lost.
Use aquantia_link_is_up instead, which checks both system and line side on
gen 2/3 PHYs to avoid losing the 1st packet.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Aquantia PHYs have a SMBus interface mostly used for debug. The addresses
on this interface are normally set up by PHY firmware, but depending on the
board they may end up not being unique. Add an optional DT property used
to change SMBus address if needed.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
MDI pins up to the RJ45 connector may be reversed on the board and the
default PHY configuration applied by firmware may or may not match that.
Add an optional DT property to configure MDI reversal for this case.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If PHY is not ready for data by the time _config is called, reconfigure the
PHY system interface to use the proper protocol based on phydev->interface,
just in case the defaults set by PHY firmware don't match current
configuration.
Signed-off-by: Florin Laurentiu Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Uses the data field in phy_driver structure to identify the PHY generation.
This is useful for custom configuration as non-generic PHY registers are
not 100% compatible between generations.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The PHY supports XFI and USXGMII, the notable difference being that USX AN
is enabled for USXGMII. Legacy code uses XGMII for any 10G proto and
detects whether USX AN should be enabled or not using a PHY status
register. Keep that functionality too, so we don't break existing drivers.
Signed-off-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix vendor name in MV88E61xx option description.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Support probing and init for 88E6071 switch.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On mv88E6071 the 'EDet' field offset, width and sense control
bits are different, adjust the driver to init the PHY control
register as needed. This fixes not working link detection and
tftp transfers.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On 88E6071 chip the port status register bit field offsets
for duplex and link bits differ. Extend the driver to use
88E6071 specific offset values. The width of bit fields for
speed status differ, too. Adapt for proper port speed
detection on 88E6071.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Extend the driver to init switch register offsets from variables
instead of compile time macros and enable detection of 88E6071 and
compatible devices. Ethernet transfer (e.g. tftp) does not work yet,
so enable the registration of the 'indirect mii' bus for easier PHY
register access by 'mii' command.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The KSZ8081 PHY has a factory test mode which is set at the de-assertion
of the reset line based on the RXER (KSZ8081RNA/RND) or TXC
(KSZ8081MNX/RNB) pin. If a pull-down is missing, or if the pin has a
pull-up, the factory test mode should be cleared by manually writing a 0
(according to the datasheet).
Create another ksz8081_config function to handle this case.
Suggested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Aquantia quad-phys may take longer to initialize. This commit adds
a polling mechanism for a global alarm bit that tells if phy init
sequence is completed.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This allows passing arbitrary addresses through macb_miiphy_read and
macb_miiphy_write, therefore enabling the mii command to access
all mdio bus devices instead of only the defined phy.
Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
To support accessing arbitrary addresses the mii/mdio bus it is
necessary that the macb_mdio_read and macb_mdio_write functions
do not implicitly use the address of the connected phy.
The function signature is extended according to the Linux kernel
equivalent.
Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
I've noticed that in most cases when genphy_update_link() is called, the
ethernet driver (mt7628-eth in this case) fails with the first ethernet
packets. Resulting in a timeout of the first tftp command. Increasing
the delay in the link check look from 1 to 50 ms and moving it below the
BMSR register read fixes this issue, resulting in a stable ethernet
traffic, even after initial link autonogotiation.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This version of the RTL-8168 chip can be found on some add-in cards sold
by CSL-Computer GmbH & Co. KG. The chip isn't special in any way, but it
needs to have the ChipCmd register programmed after the DMA descriptors
have been set up, so make sure that happens by adding an entry to the
chip information table.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Changes to mvpp2.c require the MVMDIO module which in turn uses
DM_MDIO.
Signed-off-by: Nevo Hed <nhed+github@starry.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit ports mvpp2 to use the recently introduced Marvell MDIO
(MVMDIO) driver. It removes direct interaction with the SMI & XSMI
busses. This commit is based in part on earlier work by
Ken Ma <make@marvell.com> in Marvell's own downstream repo:
https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/commit/c81dc39.
The above refrenced work was based on an MVMDIO implementation that
never made it into U-Boot. With this patch the mvpp2 driver switches
to use the new MVMDIO driver that is based on a more universal
mdio-uclass implementation.
Signed-off-by: Nevo Hed <nhed+github@starry.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If the phy doesn't match with any existing u-boot drivers, the phy
framework will connect it to the generic one which uid ==
0xffffffff. In this case, act as if the phy wouldn't be declared in
dts. Otherwise, in case of 3310 (for which the driver doesn't exist)
the link is marked as always down. Removing phy entry from dts in case
of 3310 is not a good option because it is required for the
phy_fw_down procedure.
This patch fixes the issue with the link always down on MCBIN board.
nhed: added NULL deref test.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Tested-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Nevo Hed <nhed+github@starry.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Issue:
- Network stuck if autonegotion fails.
Issue root cause:
- When autonegotiation fails during port open procedure, the packet
processor configuration does not finish and open procedure exits
with error.
- However, this doesn't prevent u-boot network framework from
calling send and receive procedures.
- Using transmit and receive functions of misconfigured packet
processor will cause traffic to get stuck.
Fix:
- Continue packet processor configuration even if autonegotiation
fails. Only error message is triggered in this case.
- Exit transmit and receive functions if there is no PHY link
indication.
- U-boot network framework now calls open procedure again during next
transmit initiation.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Tested-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Refactor SGMII configuration to group all settings together and reduce
number of MDIO transactions.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Based on commit 27708eb5481b ("net: phy: dp83867: IO impedance is not
dependent on RGMII delay") of mainline linux kernel.
The driver would only set the IO impedance value when RGMII internal delays
were enabled. There is no reason for this. Move the IO impedance block
out of the RGMII delay block.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Based on commit c11669a2757e ("net: phy: dp83867: Rework delay rgmii delay
handling") of mainline linux kernel.
The current code is assuming the reset default of the delay control
register was to have delay disabled. This is what the datasheet shows as
the register's initial value. However, that's not actually true: the
default is controlled by the PHY's pin strapping.
This patch:
- insures the other direction's delay is disabled If the interface mode is
selected as RX or TX delay only
- validates the delay values and fail if they are not in range
- checks if the board is strapped to have a delay and is configured to use
"rgmii" mode and warning is generated that "rgmii-id" should have been
used.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Based on commit 13c83cf8af0d ("net: phy: dp83867: Add ability to disable
output clock") of mainline linux kernel.
Generally, the output clock pin is only used for testing and only serves as
a source of RF noise after this. It could be used to daisy-chain PHYs, but
this is uncommon. Since the PHY can disable the output, make doing so an
option. I do this by adding another enumeration to the allowed values of
ti,clk-output-sel.
The code was not using the value DP83867_CLK_O_SEL_REF_CLK as one might
expect: to select the REF_CLK as the output. Rather it meant "keep clock
output setting as is", which, depending on PHY strapping, might not be
outputting REF_CLK.
Change this so DP83867_CLK_O_SEL_REF_CLK means enable REF_CLK output.
Omitting the property will leave the setting as is (which was the previous
behavior in this case).
Out of range values were silently converted into DP83867_CLK_O_SEL_REF_CLK.
Change this so they generate an error.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The driver ti.c is actually driver for TI DP83867x PHYs, so rename it
accordingly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix 'mask' calculation in phy_connect() for phy addr '0'.
'mask' is getting set to '0xffffffff' for phy addr '0'
in phy_connect() whereas expected value is '0'.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reported-by: tetsu-aoki via github
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
-----------------
- imx8qxp_mek: increase buffer sizes and args number
- Fixes for imx7ulp
- imx8mm: Fix the first root clock in imx8mm_ahb_sels[]
- colibri_imx7: reserve DDR memory for Cortex-M4
- vining2000: fixes and convert to ethernet DM
- imx8m: fix rom version check to unbreak some B0 chips
- tbs2910: Disable VxWorks image booting support
-----BEGIN PGP SIGNATURE-----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=L2zo
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191209' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
Fixes for 2020.01
-----------------
- imx8qxp_mek: increase buffer sizes and args number
- Fixes for imx7ulp
- imx8mm: Fix the first root clock in imx8mm_ahb_sels[]
- colibri_imx7: reserve DDR memory for Cortex-M4
- vining2000: fixes and convert to ethernet DM
- imx8m: fix rom version check to unbreak some B0 chips
- tbs2910: Disable VxWorks image booting support
In the next commit, rtc_mktime(), for compatibility with linux, will be
implemented using rtc_mktime(), which is no longer drivers/rtc specific.
So move this file under lib/.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Many boards do not use all selected framebuffer depth
configurations, for such boards there is some unused
code in video and console uclass routines. Make depth
specific code optional to avoid dead code and slightly
reduce binary size. Also make ANSI code optional for
the same reason. When i.e. using only VIDEO_BPP16 the
code size shrinks (below values when using gcc-7.3.0):
$ ./tools/buildman/buildman -b video-wip -sS wandboard
...
01: Merge git://git.denx.de/u-boot-sh
02: video: add guards around 16bpp/32bbp code
03: video: make BPP and ANSI configs optional
arm: (for 1/1 boards) all -776.0 bss -8.0 text -768.0
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Many boards use only single depth configuration, for such boards
there is some unused code in video and console uclass routines.
Add guards to avoid dead code.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
- rockchip pwm driver update to support all the SoCs
- RK3308 GMAC and pinctrl support
- More UART interface support on PX30 and pmugrf reg fix
- Fixup on misc for eth_addr/serial#
- Other updates on variant SoCs
The 24MHz oscillator clock is referenced by "clock-osc-24m" and not
"osc_24m".
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
In case the BMP size is bigger than the frame buffer, don't use
the BMP's width and height in video_display_rle8_bitmap, but the
one's checked in video_bmp_display() as parameters to
video_display_rle8_bitmap().
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
CC: Yannick Fertré <yannick.fertre@st.com>
Convert panel_picture_delta and axis_alignment from unsigned long
to long to insure to store correctly the difference between
panel_size and picture_size in case the panel_size is smaller
than picture_size.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
CC: Yannick Fertré <yannick.fertre@st.com>
[agust: change axis_alignment to long]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
An iomux register contains 8 pins, each of which is represented
by 2 bits, but the register offset is 0x8.
For example, GRF_GPIO0A_IOMUX offset is 0x0, but GRF_GPIO0B_IOMUX
offset is 0x8, the offset 0x4 is reserved.
So add a type IOMUX_8WIDTH_2BIT to calculate offset.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This PWM driver can be used to support pwm functions
for on all Rockchip Socs.
The previous chips than RK3288 did not support polarity,
and register layout was different from the RK3288 PWM.
The RK3288 keep the current functions.
RK3328 and the chips after it, which can support hardware lock,
configure duty, period and polarity at next same period, to
prevent the intermediate temporary state.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the glue code to allow the rk3308 variant of the Rockchip gmac
to provide network functionality.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The mmc CID value is one of the input parameters used to provision the
RPMB key. The trusted execution environment expects this value to be
specified in big endian format.
Before this fix, on little endian systems, the value returned by the
linux kernel mmc driver differed from the one returned by u-boot.
This meant that if linux provisioned the RPMB key, u-boot would not
have access to the partition (and the other way around).
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
PCI devices may be disabled in the device tree. Devices which are probed
by the device tree handle the "status" property and are skipped if
disabled. Devices which are probed by the PCI enumeration don't check
that property. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Alex Marginean <alexandru.marginean@nxp.com>
Tested-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move MTD-related lines out of the root Makefile. Put them in their
respective directories. Enclose some of these new lines to skip them
when building the SPL. MTD core files and some MTD device drivers are
compiled in a mtd.o object and included in the final object only if
MTD support is required (there are two different symbols for that, one
for U-Boot and one for the SPL).
Now that all defconfigs have been fixed, we can stop the logic where
enabling a command selects the core files to compile. This logic is
broken since selecting a symbol with a 'depends on' will not enforce
this secondary dependency.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The 'sf' command is not supposed to rely on the MTD stack, but both
'sf' and 'nand' commands use helpers located in mtd_uboot.c. Despite
their location, these functions do not depend at all on the MTD
stack.
This file (drivers/mtd/mtd_uboot.c) is only compiled if CONFIG_MTD is
selected, which is inconsistent with the current situation. Solve this
by moving these three functions (which are only used by the above two
commands) out of mtd_uboot.c and put them in a C file only compiled
with cmd/sf.c and cmd/nand.c.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Don't export get_part function now]
Signed-off-by: Tom Rini <trini@konsulko.com>
It is already the case that all defconfigs with SPI_FLASH_MTD also
declare using MTD, but let's make this consistent and enforce it in
Kconfig. Most of the time SPI_FLASH_MTD is used in conjunction with
UBI, which already depends on MTD.
Suggested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
CONFIG_DFU_NAND needs the raw NAND core being compiled.
Also fix the colibri_vf defconfig to reflect this dependency.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Because of the include's game, when some files are compiled for a SPI
NAND device, no warning appears. But when it is for a raw NAND device,
GCC complains. Fix these warning by including <common.h>.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Like in Linux, just use CONFIG_MTD to compile the MTD stack.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
CONFIG_MTD must be reserved for the MTD core. Like any other
subsystem, prefix the symbol by DM when it comes to DM support.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
[trini: Add Kconfig files]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Add null pointer check to take care of out of memory errors.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
The MMC boot is currently broken on omapl138-lcdk after enabling the
driver model in SPL. The main problem is the driver's bind callback not
being called after probe in SPL (even with the DM_FLAG_PRE_RELOC flag
specified).
While a proper fix is still being worked on, this hacky changeset at
least fixes the MMC boot on this platform by calling mmc_bind()
manually from probe().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
struct mmc_config & struct mmc don't need to be exported over platform
data, but can instead be private in the driver.
Remove struct davinci_mmc_plat.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The DM family of DaVinci SoCs is no longer supported. Drop the
irrelevant code from the driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When we do not have CONFIG_BLK (or SPL/TPL) enabled there are very few
cases where we need the blk_legacy code linked in. To catch these, build
when we have CONFIG_HAVE_BLOCK_DEVICE set. In addition, we only need
cmd/blk_common.o to be linked in when we have CONFIG_HAVE_BLOCK_DEVICE
set, so make use of that directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
The array 'mtd_table' is unused in the code. Remove this as gcc doesn't
always discard unused global variables.
Signed-off-by: Tom Rini <trini@konsulko.com>
The content of pci_rom.c is only used in a few cases. Only build and
link in these cases to avoid a global variable as gcc doesn't always
discard those when they are unused.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_CORTINA_FW_IN_MMC
CONFIG_SYS_CORTINA_FW_IN_NAND
CONFIG_SYS_CORTINA_FW_IN_NOR
CONFIG_SYS_CORTINA_FW_IN_REMOTE
CONFIG_SYS_CORTINA_FW_IN_SPIFLASH
Signed-off-by: Tom Rini <trini@konsulko.com>
Make the at91_gpio driver set sensible GPIO bank names in the platform
data. This makes the 'gpio status' command a lot more useful.
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
These functions do not use driver model but are still used. Move them to a
new eeprom.h header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function can be dropped when all boards use driver model for PCI. For
now, move it into init.h with a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move this function into init.h which seems to be designed for this sort
of thing. Also update the header to declare struct global_data so that it
can be included without global_data.h being needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move these functions into the command.h header file which is a better fit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move these two functions into the irq_funcs.h header file. Also move
interrupt_handler_t as this is used by the irq_install_handler() function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions do not use driver model but are fairly widely used in
U-Boot. But it is not clear that they will use driver model anytime soon,
so we don't want to label them as 'legacy'.
Move them to a new irq_func.h header file. Avoid the name 'irq.h' since it
is widely used in U-Boot already.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.
Move them over.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function belongs in time.h so move it over and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function belongs in time.h so move it over and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in time.h so move them over and add comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move this function header to serial.h since this function is clearly
related to serial. The function itself stays in console.c since we don't
have a single serial file. DM and non-DM each has a separate file so we
would have to either create a new common serial file, or repeat the
function in both serial.c and serial-uclass.c, neither of which seem
worthwhile.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The function declarations in serial.h are not in sync with what is
currently used in usbtty. Fix this by updating the header and including
it, to help catch future such problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present this function sits in its own file but it does not really
justify it. There are similar string functions in vsprintf.h, so move it
there. Also add the missing function comment.
Use the vsprintf.h include file explicitly where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Drop inclusion of crc.h in common.h and use the correct header directly
instead.
With this we can drop the conflicting definition in fw_env.h and rely on
the crc.h header, which is already included.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
We have an existing U-Boot header for the one function that this defines.
Use that instead of the linux/ one. Move over the nice comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are a few whitespace problems with this code. Tidy them up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is only used by a few files so it should not be in the common header.
Move it out.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
With commit f0921f5098 ("fdt: Sync up to the latest libfdt"),
SiFive Unleashed board does not boot any more. This was due to
the U-Boot local changes commit 77d7fff8ce ("fdt: Fix handling
of paths with options in them") to libfdt/fdt_ro.c was dropped
during the libfdt upgrade.
>From the history [1] it was mentioned that the U-Boot changes
commit 77d7fff8ce ("fdt: Fix handling of paths with options in
them") was rejected by libfdt upstream, hence we need find another
way to fix the things.
This commit uses another method, by updating serial_check_stdout()
directly to handle the situation of "stdout-path" with ":options".
A simpler way is to change the logic in fdtdec_get_chosen_node()
to do similar thing, but I feel that not every property in chosen
node may have the option in them, hence it would make more sense
to do the special handling in serial_check_stdout() directly.
[1]: http://patchwork.ozlabs.org/patch/462756/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of using single fixed value for the calibration offset,
add tables which dynamically adjust this per calibration code
from the SCC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Some of the tuning taps produce suboptimal results. Add code
which skips those "bad" taps.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Check SCC for errors after check command if applicable and
optionally adjust the bus skew settings accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Disable the auto-retuning in HS400 mode in favor of manual calibration.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Adjust the TMPPORT3 offsets according to the latest information
from the chip vendor.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Adjust the DT2FF offsets in HS400 according to latest information
from the chip vendor.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The M3W up to ES1.2 uses 4 tuning taps for HS400, make it so.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Retain the SMPCMP value from last calibration in private data.
This will be later used for skipping bad taps.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Retain the tap number from last calibration in private data. This
will be later used for SCC error checking after each command.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch is to get clock directly from global data.
- Remove uclass clk api method. This was what i.MX platforms were
using, while QorIQ platforms weren't.
- Get clock only from global data, dropping mxc_get_clock().
QorIQ eSDHC controllers on one silicon use same reference clock.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
- fix boot banner on RPi3/4
- add support for one binary on RPi3/4
-----BEGIN PGP SIGNATURE-----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=4Z+A
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2020.01' of https://github.com/mbgg/u-boot
- add RPi4 upstream compatible to pinctrl
- fix boot banner on RPi3/4
- add support for one binary on RPi3/4
Allow the unit test to pass full 8 byte scan code sequences to the USB
keyboard emulation driver and to parse multi-byte escape sequences.
The following features are not yet tested:
* LED status
* caps-lock
* num-lock
* numerical pad keys
The following features are not yet implemented by the USB keyboard
driver and therefore not tested:
* modifiers for non-alpha-numeric keys, e.g. <SHIFT><TAB> and <ALT><F4>
* some special keys, e.g. <PRINT>
* some modifiers, e.g. <ALT> and <META>
* alternative keyboard layouts
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Provide support for F1-F12, Insert, Delete, Home, End, Page Up, Page Down.
As this leads to a size increase provide a customizing setting
CONFIG_USB_KEYBOARD_FN_KEYS.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Commit ec3dcea744 ("video: mxsfb: Configure the clock after eLCDIF reset")
causes boot regression on imx7d-pico/imx7d-sdb boards, so revert it
until a better solution is prepared.
This reverts commit ec3dcea744.
Reported-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
U-Boot support on Raspberry Pi 4 relies on the device-tree
provided by the firmware. The blob does not contain the
U-Boot specific pre-loc-rel properties. The result is, that
the U-Boot banner is not printed.
We fix this by setting the DM_FLAG_PRE_RELOC flag in the driver,
if we rely on a device-tree provided by the firmware.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The Raspberry Pi 4 upstream kernel device tree instroduces
a new compatible for the pinctroller. Add this to the driver
so that we can boot with the upstream kernel DT.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>