Switches on the IMX7 pinctrl driver for the warp7 and warp7_bl33 ports,
necessary to convert over to DM for this board.
It is necessary to switch on pinctrl and GPIO in one go.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
This patch adds DT file hooks for imx7s-warp.dtb to the warp7 and
warp7_bl33 builds.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable SPL for i.MX8QXP MEK, and currently use SPL FIT.
The SPL enable SPL_DM to use MMC/PINCTRL/POWER DOMAIN/CLK.
Note: SPL FIT could not support secure boot chain, because i.MX8/8X
only support i.MX container format. This container format has
not been upstreamed, so we use FIT for now. When SPL container
supported, we could switch to that.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The defconfig already use most features implied by distro defaults.
Make sure we enable all features required by distro boot by making
use of CONFIG_DISTRO_DEFAULTS.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
The colibri_imx7_defconfig is for Colibri iMX7 raw NAND devices.
Hence DFU for NAND is more useful then for MMC devices.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Access to CAAM in non-secure mode must be enabled by the boot
loader first. The U-Boot CAAM driver enables access to CAAM in
non-secure mode by default. Hence enable the CAAM driver to
allow Linux accessing CAAM directly. This prevents error
messages like the following on Linux boot:
caam 30900000.caam: Entropy delay = 3200
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: failed to instantiate RNG
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Now that device tree is in place use DM_MMC for Colibri iMX7
devices.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Use OF_SEPARATE as suggested by the build system.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Use DM and device trees for raw NAND devices by default. This
fixes -74 NAND read errors since it makes sure the ECC settings
are the same as used in Linux and our downstream U-Boot.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
In preparation of adding CONFIG_DM_MMC support use separate device
trees for raw NAND and eMMC devices.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add support for the VXT VL050-8048NT-C01 panel connected through
the 24 bit parallel LCDIF interface.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Port for the PHYTEC phyBOARD-i.MX6UL-Segin single board computer. Based on
the PHYTEC phyCORE-i.MX6UL SOM (PCL063).
CPU: Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 44C
Reset cause: POR
Board: PHYTEC phyCORE-i.MX6UL
I2C: ready
DRAM: 256 MiB
NAND: 512 MiB
MMC: FSL_SDHC: 0
In: serial
Out: serial
Err: serial
Net: FEC0
Working:
- Eth0
- i2C
- MMC/SD
- NAND
- UART (1 & 5)
- USB (host & otg)
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
I'm working on getting OpenBSD to run on the Atmel SAMA5D3 Xplained.
OpenBSD uses an EFI bootloader, which requires the "load" command to
work, since "fatload" doesn't initialize the EFI memory addresses
properly. To get "load" on the SAMA5D3 version of U-Boot, I propose
adding the CONFIG_CMD_FS_GENERIC option.
Signed-off-by: Greg Czerniak <greg@czerniak.info>
A few platforms recently added in CONFIG_DFU_MMC under include/configs
rather than via the defconfig, update them.
Signed-off-by: Tom Rini <trini@konsulko.com>
A couple of trivial fixes and improvements for ARC
Most notable are:
* Move of ENV_SIZE/ENV_OFFSET to Kconfig
* Fix with private structure allocation for arc_uart
* Definition of CONFIG_SYS_CACHELINE_SIZE useful for building drivers
Join the party of some ARM boards and drop more
items from include/configs/xxx.h.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
There is no i2c connected in base DT that's why disable I2C commands.
Also remove zynq_zybo which is not needed now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Build warning was added by:
"fdt: Add warning about CONFIG_OF_EMBED"
(sha1: 841d5fbae4)
Zynq mini configurations are not moved yet and it is questionable if
make sense to move them too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Build warning was added by:
"fdt: Add warning about CONFIG_OF_EMBED"
(sha1: 841d5fbae4)
ZynqMP mini configurations are not moved yet and it is questionable if
make sense to move them too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable ISSI flash for platforms. Xilinx reference boards are also used
internally with different flash part to increase coverage that's why
enable also ISSI parts for all these boards even if that board is
released only with one part.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch enable net configs for zc1275 board.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add board support and configuration for Jaguar2 SoC family.
The detection of the board type is based on the phy ids.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add board support, configuration and DTS for Servalt SoC
family. Currently there is one board in this family.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Now that network support is added for the ocelot platform, let's add it
in the default configuration.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
- Sync Armada-38x dts with Linux 4.20 from Chris
- Misc changes and enhancements to Turris Mox (v4) from Marek
- Reserve PSCI area for Armada 8k from Heinrich
- New Allied Telesis x530 board (Armada-385) from Chris
- Misc minor changes (defconfig etc)
This is a range of stackable network switches. The SoC is Armada-385 and
there are a number of variants with differing network port
configurations. The DP variants are intended for a harsher operating
environment so they use a different i2c mux and fit industrial-temp
parts.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
An NVME drive may be installed on the MACCHIATObin board using the PCIe
slot or on the Clearfog Pro using mini a PCI-e slot. With the configuration
change it becomes usable.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add gpio command to defconfig - this can be used to detect whether the
button is pressed or light LEDs.
Add DS1307 RTC driver and the date command.
Add CONFIG_WATCHDOG, so that U-Boot calls watchdog_reset.
Add CONFIG_MISC_INIT_R so that ethernet addresses are read from OTP
before network controller is initialized.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The bounce buffer is used by a few drivers (most of the MMC drivers)
to overcome limitations in their respective DMA implementation.
This moves the configuration to Kconfig and makes it user-selectable
(even though it will be a required feature to make those drivers
work): the expected usage is for drivers depending on this to 'select'
it unconditionally from their respective Kconfig (see follow-up
patches).
This commit includes a full migration using moveconfig.py to ensure
that each commit compiles. To ensure bisectability we update
dependencies of various drivers to now select BOUNCE_BUFFER when needed.
[trini: Squash all patches to ensure bisectability]
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br> [dw_mmc portion]
Reviewed-by: Fabio Estevam <festevam@gmail.com> [mxsmmc portion]
Reviewed-by: Simon Glass <sjg@chromium.org> [tegra portion]
The am335x_evm_defconfig supports all am335x_boneblack variants. Remove
the redundant am335x_boneblack_defconfig.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On this board SPI is only used to configure the SoC driving the LC TFT
display which is not used in U-Boot. Hence remove SPI support.
Signed-off-by: Felix Brack <fb@ltec.ch>
Onc of key blocker for using USB Generic host controller
drivers in Allwinner are CLK and RESET drivers, now these
available for USB usage.
So switch sunxi USB use EHCI and OHCI Generic controllers.
Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD
where it already have USB_EHCI_HCD
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Emlid Neutis N5 is a SoM based on Allwinner H5, has a WiFi & BT
module, DDR3 RAM and eMMC.
- add neutis-devboard target to dtb makefile
- add dtsi file for Neutis N5 needs
- add config file for Neutis N5 Dev board
Signed-off-by: Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: update proper commit head]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
am43xx_evm_ethboot_defconfig is not being actively used and has not been
moved to DM or DT. Also, ethboot cannot be tested on AM43xx EVM as such
due EVM limitations. Therefore delete it.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These defconfigs don't seem be actively used any more, and have not been
moved to adapt DM or DT. Therefore delete them.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
bananapi r2 can be booted from sd-card and emmc
saving the environment have to choose the storage
from which the device has booted
also the offset is set to 1MB to make sure env is written
to block "user data area" between uboot and first partition
https://www.fw-web.de/dokuwiki/lib/exe/fetch.php?cache=&media=bpi-r2:boot-structure.png
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
update TFABOOT defconfig for SD boot on below NXP chasis2
and chasis3 platforms:
ls1043a, ls1046a, ls1088a and ls2088a.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls2088aqds_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls2088ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- remove EL3 specific erratas for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1088aqds_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- MC address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- ifc chip select changes for TFABOOT
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1088ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- MC address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- ifc chip select changes for TFABOOT
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
With the new SPI NOR framework in v4.19, we need to adapt the MTD parts
so that the kernel cmdline parameter "mtdparts=" uses the correct naming
for the devices.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Fix the Kconfig warning to not use CONFIG_OF_EMBED in defconfigs.
Based on https://patchwork.ozlabs.org/patch/1019791/
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add board support and configuration for Jaguar2 SOC family.
The detection of the board type in this family is based on the phy ids.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Thes patch change the luton base device tree to use the newly added
SPI bitbang driver.
It also updates the "mscc_luton_defconfig" to use the new driver.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
There is no real difference between the generic variant and
the custom variant except that the generic variant is more
optimised. This also saves 24 Bytes in the SPL binary.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@collabora.com>
This enables the use of the MSCC serial GPIO driver to control the
LEDs on the MSCC VCoreIII 'ocelot' pcb123 and pcb120.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
This enables the use of the MSCC serial GPIO driver to control the
LEDs on the MSCC VCoreIII 'luton' SoC.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
As we are moving to multi-dtb and board detection, remove static board
config options, and introduce board probing instead.
Luton: This add single-binary support for the two MSCC luton-based
reference boards - pcb090 and pcb091. The SoC chip ID is used to
determine the board type.
Ocelot: This add single-binary support for the two MSCC ocelot-based
reference boards - pcb120 and pcb123. The PHY ids on specific ports
are used to determine the board type.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Building with CONFIG_OF_EMBED generates build warnings, as it should
only be used for debugging purposes.
Remove CONFIG_OF_EMBED from all stm32 config files which are using
this flag.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This adds device tree for OMAP3 IGEP based boards and the DM_MMC driver.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The USB support for this board was never really tested, in fact, the
presence of these options are more a copy & paste error from the
Beagleboard than a feature that really was used. As doesn't work, remove
for now. If someone at some point want to add this support he'll need to
migrate the board to use CONFIG_DM_USB instead.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
The IGEP0032 board was never officially pushed upstream and actually I
don't have access to this hardware, unless someone with the hardware
wants to start working on this doesn't makes sense have this defconfig
here. So remove it.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Convert HiSilicon HI6220 MMC driver based on DWMMC IP to driver
model.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Enable this on poplar]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch replace OF_EMBED with OF_SEPARATE of defconfig files of
MediaTek boards because now OF_EMBED is only used for debugging purpose.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable ethernet related configs to mt7629_rfb_defconfig.
Add default IP addresses.
Enable noncached memory region required by ethernet driver.
Signed-off-by: Mark Lee <Mark-MC.Lee@mediatek.com>
Enable ethernet related configs to mt7623n_bpir2_defconfig.
Add default IP addresses.
Enable noncached memory region required by ethernet driver.
Signed-off-by: Mark Lee <Mark-MC.Lee@mediatek.com>
Add a test for the bootcount uclass, which uses the RTC bootcount backend
(i.e. drivers/bootcount/rtc.c is implictly also tested).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Chris Spencer reports that when enabling ext4 read support without
also enabling write support the following error is seen:
fs/fs.c:198:12: error: 'ext4_write_file' undeclared here (not in a
function); did you mean 'ext4_read_file'?
.write = ext4_write_file,
^~~~~~~~~~~~~~~
Fix this problem by moving these options to Kconfig.
Reported-by: Chris Spencer <spencercw@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
There is no need to compile and include this code if it is not used.
CONFIG_USB_GADGET can be used for the purpose.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The current defconfig build generates a u-boot.imx file that is too large
for the available space on a eMMC/SD card. Installing this file overwrites
the u-boot environment. So disable the unused FIT support to reduce the
size of the u-boot binary.
Signed-off-by: Soeren Moch <smoch@web.de>
Safe some space by not selecting CMD_NFS and CMD_LOADS/B.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This patch enables the full pinctrl driver in the defconfig
for the RK3399-Q7.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch enables the PWM regulator driver in the defconfig
for the RK3399-Q7.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable driver model for USB, MMC and REGULATOR drivers.
Set run-time configuration via Device Tree.
Signed-off-by: Yaniv Levinsky <yaniv.levinsky@compulab.co.il>
CONFIG_CMD_BOOTEFI is enabled by Kconfig default, but rarely
used on this board/platform.
So let's disable it for the boards default config.
This also saves around 16 KiB in the final u-boot.sb.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
While migrating individual status led usages to Kconfig stuff,
a (random) value was introduced for this board which does not
work but produces the following error message during boot:
__led_init: failed requesting GPIO59!
Since Kconfig does not seem to accept a define as this point,
but the mxs gpio driver requires not only a simple integer value,
we need to use the plain value of MX23_PAD_SSP1_DETECT__GPIO_2_1.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Fixes: 2d8d190c83 ("status_led: Kconfig migration")
Use defconfig instead of header file for CONFIG_CMD_PCI.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some users might need additional setups before booting the kernel.
If there is found a file 'boot.scr', run it before invoking the
distro boot command.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Some users might want to modify 'bootcmd' at compile-time by editing
include/configs/uniphier.h, but overwriting it at run-time makes it
impossible.
Instead, set 'bootdev' at run-time, which contains the boot device the
system is booting from, then indirectly reference it from 'bootcmd'.
It is up to users whether to override 'bootcmd'.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
As an example of how to enable TrueType fonts, move chromebook_jerry over
to use these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
db-88f6820-amc uses CONFIG_DM_USB and CONFIG_USB_STORAGE already so
define CONFIG_BLK to prepare it for full conversion to DM.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for the Creator CI20 platform based on the JZ4780 SoC.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Adding the support for the Luton boards PCB91 which share common code with
the Ocelots boards, including board code, device tree and configuration.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Building with CONFIG_OF_EMBED generates build warnings, as it should
only be used for debugging purposes. So let's move all MT7688 targets to
CONFIG_OF_SEPARATE instead with this patch.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Remove cpu name from the defconfig naming.
Because other cpus maybe run on AE350 platform.
So only use platfrom name in defconfig naming
will be better.
Also sync MAINTAINERS:
Rename
a25-ae350_32_defconfig as ae350_rv32_defconfig
ax25-ae350_64_defconfig as ae350_rv64_defconfig
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use standard configuration logic to define EEPROM constants.
Names are based on VPD_EEPROM_ prefix because EEPROM_ is already
used by i2c_eeprom driver.
Signed-off-by: Denis Zalevskiy <denis.zalevskiy@ge.com>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
Add the initial support for Elgin R1 board, which is based on the
RV1108 SoC and has the following features currently supported in
U-Boot:
- UART
- eMMC
- USB
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The motivation for this is to allow distributions to distribute all
possible tools in a generic way, avoiding the need of specific tools
building for each machine.
Especially on OpenEmbedded / Yocto Project ecosystem, it is very
common each BSP to end providing their specific tools when they need
to generate images for some SoC (e.g MX23 / MX28 in meta-freescale
case).
Using this, we can package the tools doing:
$: make tools-only_defconfig
$: make tools-only
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
[trini: Add MAINTAINERS entry for myself, add to .travis.yml, make
U-Boot itself buildable to not trip up other frameworks]
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable DM_USB and DM_USB_GADGET for this platform. Also enable RNDIS boot
support (SPL load u-boot over USB RNDIS).
This is an example of how to use DM_USB on a am335x-based board.
A subsequent series will take this a step further and modify more
defconfigs.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The AM43xx SOCs have the ability to download the SPl through USB (RNDIS).
Adding support for RNDIS in SPL allows to also download u-boot through USB.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The K2G evm uses the generic DWC3 driver. DFU can thus be enabled.
Enabling DFU for easier firmware update.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The keystone platforms can use the generic DC3 driver. Removing the
keystone-spcecific xchi driver and add the configuration options to enable
the generic DWC3 driver on all K2 platforms.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update snow's device tree and config to use driver model for sound. Also
update the others as best we can.
Spring does not appear to have audio support in the kernel. The smdk5250
and smdk5420 boards use a wolfson codec which I cannot test with. So the
only boards that is tested and known to work are snow, pit and pi.
Signed-off-by: Simon Glass <sjg@chromium.org>
The existing config is setup as a gadget but it doesn't use
DM_USB. This patch converts all boards to DM_USB, but as host.
As host, it is able to mount USB drives and browse them.
Signed-off-by: Adam Ford <aford173@gmail.com>
There is no need for an embedded device tree for this board so let the
build process generate a separate u-boot.dtb file instead.
Signed-off-by: Felix Brack <fb@ltec.ch>
Building U-Boot with CONFIG_PCI and CONFIG_DM_PCI enabled, but
CONFIG_SPL_PCI_SUPPORT disabled, results in following linker
error:
lib/built-in.o: In function `fdtdec_get_pci_bar32':
lib/fdtdec.c:305: undefined reference to `dm_pci_read_bar32'
fdtdec.c:305:(.text.fdtdec_get_pci_bar32+0x24): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `dm_pci_read_bar32'
This is because reference to dm_pci_read_bar32() remains in lib/fdtdec.c
while SPL build does not descend into drivers/pci directory in
drivers/Makefile if CONFIG_SPL_PCI_SUPPORT is not enabled.
Fix this by applying appropriate #define guards in lib/fdtdec.c.
It looks like ns16550.c has the same problem, so fixed that too.
To simplify this, CONFIG_SPL_PCI_SUPPORT is renamed to CONFIG_SPL_PCI
(enables use of CONFIG_IS_ENABLED() macro).
Suggested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>