sp805 is watchdog on some NXP layerscape SoCs, adding
it's driver. Configs CONFIG_WDT_SP805, CONFIG_WDT, CONFIG_CMD_WDT
needs to be enabled to use it.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Distinguish the ecc val by chassis version and move the ecc addr to dts.
Add ls1028a soc support.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add the infrastructure for Layerscape SoCs PCIe Gen4 controller
to update device tree nodes to convey SMMU stream IDs in the
device tree.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add PCIe Gen4 driver for the NXP Layerscape SoCs. This PCIe
controller is based on the Mobiveil IP, which is compatible
with the PCI Express™ Base Specification, Revision 4.0.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bao Xiaowei <Xiaowei.Bao@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
It was returning an int, which doesn't work if the u32 it is reading,
or the default value, will overflow a signed int.
While it could be made to work, when using a C standard/compiler where
casting negative signed values to unsigned has a defined behavior,
combined with careful casting, it seems obvious one is meant to use
ofnode_read_s32_default() with signed values.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Add ofnode_get_addr_size_index function to fetch the address
and size of the reg space based on index.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In some cases it is necessary to read the keyboard in early phases of
U-Boot. The cros_ec keyboard is kept in the misc directory. Update the
config to allow this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since Gen3 SDHI has an internal DS signal AC-spec violation in HS400 mode,
CRC-error may occur in read command in HS400 mode. This phoenomenon occurs
at low/high temperature.
To fix this, after completion of HS400 tuning, enable manual calibration.
However, Gen3 M3 Ver.1.2 or earlier and H3 1.x does not support HS400.
These SoC forcibly use HS200 mode by SoC attribute.
The DT adjustment of the tuning parameters is not supported until the
DT property names become clear.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Adapted from a patch by Takeshi Saito <takeshi.saito.xv@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Peng Fan <peng.fan@nxp.com>
Clean up the whitespaces in macros, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Peng Fan <peng.fan@nxp.com>
Add driver for the Renesas RCar PCIe controller present on Gen3 SoCs.
The PCIe on Gen3 is used both to connect external PCIe peripherals.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
when loading the splash image from a FIT
- updates for loading internal and external splash data from FIT
- DM_GPIO/DM_VIDEO migration for mx53 cx9020 board
- fix boot issue on mx6sabresd board after DM_VIDEO migration
- increase the max preallocated framebuffer BPP to 32 in ipuv3
driver to prepare for configurations with higher color depth
- allow to use vidconsole_put_string() in board code for text
output on LCD displays
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXOK5Sw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXBvoAJ96YrInVKKWtuVigA9lNpk5xbmbeQCdG9wML4LI
dBbQyzD3mNqvnDMyNPQ=
=Plt7
-----END PGP SIGNATURE-----
Merge tag 'video-for-2019.07-rc3' of git://git.denx.de/u-boot-video
- update for using splashfile instead of location->name
when loading the splash image from a FIT
- updates for loading internal and external splash data from FIT
- DM_GPIO/DM_VIDEO migration for mx53 cx9020 board
- fix boot issue on mx6sabresd board after DM_VIDEO migration
- increase the max preallocated framebuffer BPP to 32 in ipuv3
driver to prepare for configurations with higher color depth
- allow to use vidconsole_put_string() in board code for text
output on LCD displays
The single channel detection in the gazerbeam board driver was not
implemented correctly.
Fix the detection.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
For the DM case, use the proper parameter for the regmap_init_mem call
(which is the ofnode, not the udevice).
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Make the gdsys_rxaui_ctrl polarity setting function return the old
state to comply with the API requirements.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Since the IHS I2C driver want upstream, the surrounding infrastructure
has changed quite a bit (notably, the fpgamap driver was replaced with a
regmap driver).
Update the driver to work with these changes.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Heiko Schocher <hs@denx.de>
Some DM drivers have hardcoded clk_enable calls when handling
clocks (for example the fsl_esdhc driver).
To work with these drivers, add an enable method to the MCP83xx clock
driver (which does nothing, because the clocks are always enabled).
Signed-off-by: Mario Six <mario.six@gdsys.cc>
CONFIG_SYS_DDR_SDRAM_BASE is set to the same value as
CONFIG_SYS_SDRAM_BASE on all existing boards. Just use
CONFIG_SYS_SDRAM_BASE instead.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Migrate the BR/OR settings to Kconfig. These must be known at compile
time, so cannot be configured via DT.
Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
vme8349.h contains two separate boards: The vme8349 itself, and the
caddy2 board. The caddy2 board is chosen by setting certain config
variables. Create a proper config file for the caddy2 board to make
Kconfig migration easier.
Furthermore, simplify the vme8349 and caddy2 configs by keeping only the
options necessary for each board.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
CONFIG_TARGET_VME8349 can replace CONFIG_VME8349. Hence, replace
CONFIG_VME8349 with CONFIG_TARGET_VME8349, and remove CONFIG_VME8349.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Pull the vidconsole_put_string() function from DM tests, make it
available to e.g. boards that want to display information on the
LCD on boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
The IPUv3 can handle 1920x1080x32bpp displays , set the max preallocated
framebuffer BPP to 32 to cater for all eventualities.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
This reverts commit 72a89e0da5, which
causes the imx53 HSC to hang as the eMMC is not working properly anymore.
The exact error message:
MMC write: dev # 0, block # 2, count 927 ... mmc write failed
0 blocks written: ERROR
imx53 is not using the DDR mode.
Debugging of pre_div and div generation showed that those values are
generated in a way, which is not matching the ones from working setup.
As the original patch was performing code refactoring, let's revert this
change, so all imx53 boards would work again.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
When dma_addr_t is u32 in 64-bit, there are some warnings when
building NVME driver. Fix it by doing an additional (long) cast.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
The function bcm6345_wdt_start use the argument timeout
as tick but it should be used as milliseconds.
A clock is added as requirement for this driver.
The frequency of the clock is then used to convert the
millisecond to ticks in the function bcm6345_wdt_start.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Stefan Roese <sr@denx.de>
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
These options only apply when not using DM_I2C. When using device
trees, the dt will enable and control the speeds of the I2C
controller(s) and these configuration options have no effect.
So disable them in DM_I2C mode. Otherwise they show up as decoys, and
make it look like one is enabling I2C controllers and setting the speed
when really it's doing nothing.
However, a system using a SPL build will not use DM_I2C in the SPL, even
if DM_I2C is enabled for the main u-boot. And so the SPL might use the
kconfig based I2C speed controls while the main u-boot does not.
Cc: Sriram Dash <sriram.dash@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
This is an old driver that supports both device mapped and non-mapped
mode, and covers a wide range of hardware. It's hard to change without
risking breaking something. I have to tried to be exceedingly detailed
in this patch, so please excuse the length of the commit essay that
follows.
In device mapped mode the I2C xfer function does not handle plain read,
and some other, transfers correctly.
What it can't handle are transactions that:
Start with a read, or,
Have a write followed by a read, or,
Have more than one read in a row.
The common I2C/SMBUS read register and write register transactions
always start with a write, followed by a write or a read, and then end.
These work, so the bug is not apparent for most I2C slaves that only use
these common xfer forms.
The existing xfer loop initializes by sending the chip address in write
mode after it deals with bus arbitration and master setup. When
processing each message, if the next message will be a read, it sends a
repeated start followed by the chip address in read mode after the
current message.
Obviously, this does not work if the first message is a read, as the
chip is always addressed in write mode initially by i2c_init_transfer().
A write following a read does not work because the repeated start is
only sent when the next message is a read. There is no logic to send it
when the current message is a read and next is write. It should be sent
every time the bus changes direction.
The ability to use a plain read was added to this driver in
commit 2feec4eafd ("imx: mxc_i2c: tweak the i2c transfer method"),
but this applied only the non-DM code path.
This patch fixes the DM code path. The xfer function will call
i2c_init_transfer() with an alen of -1 to avoid sending the chip
address. The same way the non-DM code achieves this. The xfer
function's message loop will send the address and mode before each
message if the bus changes direction, and on the first message.
When reading data, the master hardware is one byte ahead of what we
receive. I.e., reading a byte from the data register returns a byte
*already received* by the master, and causes the master to start the RX
of the *next* byte. Therefor, before we read the final byte of a
message, we must tell the master what to do next. I add a "last" flag
to i2c_read_data() to tell it if the message is to be followed by a stop
or a repeated start. When last == true it acts exactly as before.
The non-DM code can only create an xfer where the read, if any, is the
final message of the xfer. And so the only callsite of i2c_read_data()
in the non-DM code has the "last" parameter as true. Therefore, this
change has no effect on the non-DM code. As all other changes are in
the DM xfer function, which is not even compiled in non-DM code, I am
confident that this patch has no effect on boards not using I2C_DM.
This greatly reduces the range of hardware that could be affected.
For DM boards, I have verified every transaction the "i2c" command can
create on a scope and they are all exactly as they are supposed to be.
I also tested write->read->write, which isn't possible with the i2c
command, and it works as well. I didn't fix multiple reads in a row, as
it's a lot more invasive and obviously no one has every wanted them
since they've never worked. It didn't seem like the extra complexity
was justified to support something no one uses.
Cc: Nandor Han <nandor.han@ge.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
It is not very clear how these work in relation to the exact I2C xfers
they produce. In paticular, the address length is somewhat overloaded
in the read method. Clearly document the existing behavior. Maybe this
will help the next person who needs to work on this driver and not break
non-DM boards.
Cc: Nandor Han <nandor.han@ge.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
In mt7629-rfb.dts, the phy-handle is a reference to the node phy0, not the
node itself:
phy-handle = <&phy0>;
phy0: ethernet-phy@0 {
reg = <0>;
}
However the driver used ofnode_find_subnode("phy-handle") to read the node.
It will always fail.
This patch replaces ofnode_find_subnode with dev_read_phandle_with_args to
make sure the node can be read correctly.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This version of the RTL-8168 is present on some development boards and
is compatible with this driver. Add support for identifying this version
of the chip so that U-Boot won't complain about it being unknown.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Implement this callback that allows the MAC address to be set for the
Ethernet card. This is necessary in order for the device to be able to
receive packets for the MAC address that U-Boot advertises.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There is a need to fill node before clk_output_sel is setup.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Reviewed-by: <hannes.schmelzer@br-automation.com>
Commit d397f7c45b ("net: phy: micrel: Separate KSZ9000 drivers from
KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns
that you shouldn't select both of them due to a device ID clash between
the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a
system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately
boards like the SAMA5D3xEK do contain both types of PHY, but fortunately
the Linux Micrel PHY driver provides a solution by using different PHY
ID and mask values to distinguish these chips.
This commit contains the following changes:
- The PHY ID and mask values for the KSZ9021 and the KS8721 now match
those used by the Linux driver.
- The warnings about not enabling both drivers have been removed.
- The description for PHY_MICREL_KSZ8XXX has been corrected (these are
10/100 PHYs, not GbE PHYs).
- PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE
since this is selected by PHY_MICREL_KSZ90X1.
- All of the relevant defconfig files have been updated now that
PHY_MICREL_KSZ8XXX does not default to 'Y'.
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Convert 'gpio_dwapb_bind' to iterate over subnodes using livetree
functions (inspired from mt7621_gpio.c).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Convert 'socfpga_reset_probe' to use 'dev_read_u32_default'
instead of 'fdtdec_get_int'.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Convert 'altera_uart_ofdata_to_platdata' to use 'dev_read_u32_default'
instead of 'fdtdec_get_int' and get rid of DECLARE_GLOBAL_DATA_PTR.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Convert 'dw_spi_ofdata_to_platdata' to use 'dev_read_u32_default'
instead of 'fdtdec_get_int' and get rid of DECLARE_GLOBAL_DATA_PTR.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Convert 'cadence_spi_ofdata_to_platdata' to use dev_read_* functions to
read driver parameters and 'dev_read_first_subnode'/'ofnode_read_*' to
read flash (child node) parameters.
Tested on socfpga_socrates (socfpga gen5).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add support for loading FPGA bitstream to get DDR up running before
U-Boot is loaded into DDR. Boot device initialization, generic firmware
loader and SPL FAT support are required for this whole mechanism to work.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Add FPGA driver to support program FPGA with FPGA bitstream loading from
filesystem. The driver are designed based on generic firmware loader
framework. The driver can handle FPGA program operation from loading FPGA
bitstream in flash to memory and then to program FPGA.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Current watchdog reset is misplaced after for-loop status polling, so
this poses a risk that watchdog can't be reset timely if polling taking
longer than watchdog timeout. This patch moving the watchdog reset
into polling to ensure the watchdog can be reset timely.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Ensure all the debug messages are always prefix with "FPGA: " and comment
beginning with uppercase letter.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
This CPU core is old, no boards using the CPU are left in mainline,
it has no prospects of ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
This CPU core is old, no boards using the CPU are left in mainline,
it has no prospects of ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Drop unused macros from the header to clean it up.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
There is no RTS7751R2D support in U-Boot, drop all the RTS7751R2D macros.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
There is no SH2007 support in U-Boot, drop all the SH2007 macros.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
There is no H8 support in U-Boot, drop all the H8 macros.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
There is no 'config CRC32' remove the select that was attempting to use
it.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
CONFIG_GPIO does not exist. sysreset_gpio.c uses the DM gpio APIs so the
correct option to select is DM_GPIO.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is one case where 400ms is not sufficient for loading the
system firmware:
- System firmware is not signed with rsa degenerate key.
- ROM loading the sysfw directly from SPI flash which is in memory
mapped mode.
The above scenario is definitely not desired in production use cases
as it effects boot time. But still keeping this support as this is
a valid boot scenario.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Fix test_avb_persistent_values() pytest, which was failing because of
wrong size value provided from tee sandbox driver.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
malloc(..) and memalign(..) are both allocating memory and as a result
we leak the memory allocated with malloc(..).
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Per feedback from Marek, he suggested better handling and
to enable DM_FLAG_OS_PREPARE, this patch re-orders some of
the error checking, and errors returns the error code right
away and also sets DM_FLAG_OS_PREPARE.
Signed-off-by: Adam Ford <aford173@gmail.com>
Improvements and new features:
- split more rockchip pinctrl_core feature into per SoC
- enable TPL for evb-rk3399 board
- enable TPL/SPL for evb-px5 board
- enable TPL and OP-TEE support for evb-rk3229
- update fix in arm common assembly start code for rockchip header file
- update default SPL_FIT_GENERATOR for rockchip
- rk3399 boards update to use '-u-boot.dtsi'
- add new rk3399 boards: Nanopi M4, Nanopc T4
- enable sound for chromebook_minnie
- Add USB Complex Glue driver for Amlogic G12A
- Add USB Gadget support for Amlogic G12A
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mn/6
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20190509' of git://git.denx.de/u-boot-amlogic
- Add USB PHY drivers for Amlogic G12A
- Add USB Complex Glue driver for Amlogic G12A
- Add USB Gadget support for Amlogic G12A
This adds support for the USB PHYs found in the Amlogic G12A SoC Family.
The USB2 PHY supports Host and/or Peripheral mode, depending on it's position.
The first PHY is only used as Host, but the second supports Dual modes
defined by the USB Control Glue HW in front of the USB Controllers.
The second driver supports USB3 Host mode or PCIE 2.0 mode, depending on
the layout of the board.
Selection is done by the #phy-cells, making the mode static and exclusive.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Adds support for Amlogic G12A USB Control Glue HW.
The Amlogic G12A SoC Family embeds 2 USB Controllers :
- a DWC3 IP configured as Host for USB2 and USB3
- a DWC2 IP configured as Peripheral USB2 Only
A glue connects these both controllers to 2 USB2 PHYs, and optionnally
to an USB3+PCIE Combo PHY shared with the PCIE controller.
The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including
routing of the OTG PHY between the DWC3 and DWC2 controllers, and
setups the on-chip OTG mode selection for this PHY.
This driver sets the OTG capable port as Host mode by default,
the switch to Device mode is to be done in a separate patch.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Marek Vasut <marex@denx.de>
In some of the device trees that specify skew values for KSZ90x1 PHYs
the values are stored (incorrectly) in the MAC node, whereas in others
it is in an 'ethernet-phy' subnode. Previously the code would fail to
find and program these skew values, so this commit changes it to look
for an "ethernet-phy" subnode first, and revert to looking in the MAC
node if there isn't one.
The device trees affected (where the skew values are in a subnode) are
imx6qdl-icore-rqs.dtsi, r8a77970-eagle.dts, r8a77990-ebisu.dts,
r8a77995-draak.dts, salvator-common.dtsi, sama5d3xcm.dtsi,
sama5d3xcm_cmp.dtsi, socfpga_cyclone5_vining_fpga.dts,
socfpga_stratix10_socdk.dts and ulcb.dtsi. Before this change the skew
values in these device trees would be ignored.
The device trees where the skew values are in the MAC node are
socfpga_arria10_socdk.dtsi, socfpga_arria5_socdk.dts,
socfpga_cyclone5_de0_nano_soc.dts, socfpga_cyclone5_de10_nano.dts,
socfpga_cyclone5_de1_soc.dts, socfpga_cyclone5_is1.dts,
socfpga_cyclone5_socdk.dts, socfpga_cyclone5_sockit.dts. These should be
unaffected by this change.
The changes were tested on a sama5d3xcm.
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit ff7bd212cb ("net: phy: micrel: fix divisor value for KSZ9031
phy skew") fixed the skew value divisor for the KSZ9031, but left the
code using the same divisor for the KSZ9021, which is incorrect.
The preceding commit c16e69f702 ("net: phy: micrel: add documentation
for Micrel KSZ90x1 binding") added the DTS documentation for the
KSZ90x1, changing it from the equivalent file in the Linux kernel to
correctly state that for this part the skew value is set in 120ps steps,
whereas the Linux documentation and driver continue to this day to use
the incorrect value of 200 that came from the original KSZ9021 datasheet
before it was corrected in revision 1.2 (Feb 2014).
This commit sorts out the resulting confusion in a consistent way by
making the following changes:
- Update the documentation to be clear about what the skew values mean,
in the same was as for the KSZ9031.
- Update the Micrel PHY driver to select the appropriate divisor for
both parts.
- Adjust all the device trees that state skew values for KSZ9021 PHYs to
use values based on 120ps steps instead of 200ps steps. This will result
in the same values being programmed into the skew registers as the
equivalent device trees in the Linux kernel do, where it incorrectly
uses 200ps steps (since that's where all these device trees were copied
from).
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
For AQR405 in register 4.c441 bit 15 was override with 0. This caused the
phy to not negotiate at 2.5GB rate with mac. To avoid
this override it needed first to know the previous value of reg 4.c441
and set only bit 3.
Signed-off-by: Valentin Catalin Neacsu <valentin-catalin.neacsu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Don't ignore return value of phy_probe() call as
the probe may fail and it needs to be reported.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch relocates the pointers inside phy_drivers incase
of manual reloc. Without this reloc, these points to invalid
pre relocation address and hence causes exception or hang.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
if an error occurs in ldpaa_eth_init, need to free all resources
before returning the error.
Threfore, free net_dev before returning from ldpaa_eth_init.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add EPHY CLK and RESET support for sun8i_emac driver to
enable EPHY TX clock and EPHY reset pins via CLK and RESET
framework.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Getting a RESET by index with device is not straight forward
for some use-cases like handling clock operations for child
node in parent driver. So we need to process the child node
in parent probe via ofnode and process RESET operation for child
without udevice but with ofnode.
So add reset_get_by_index_nodev() and move the common code
in reset_get_by_index_tail() to use for reset_get_by_index()
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
clk_get_by_index_tail() now handle common clk get by index
code so use it from clk_get_by_indexed_prop().
Cc: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Getting a CLK by index with device is not straight forward
for some use-cases like handling clock operations for child
node in parent driver. So we need to process the child node
in parent probe via ofnode and process CLK operation for child
without udevice but with ofnode.
So add clk_get_by_index_nodev() and move the common code
in clk_get_by_index_tail() to use for clk_get_by_index()
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Like clk_get_by_index, there is requirement for
clk_get_by_index_nodev. In this case to make common
code functionalities for dev and nodev, clk_get_by_index
is trying to get the index of clock by passing ofnode
instead of actual dev like current gpio uclass does.
In these scenarios with current order of include files
the serial_sifive driver is unable to find CONFIG_ENV_SIZE.
In file included from arch/riscv/include/asm/u-boot.h:23:0,
from include/dm/of.h:10,
from include/dm/ofnode.h:12,
from include/clk.h:11,
from drivers/serial/serial_sifive.c:6:
include/environment.h:145:19: error: 'CONFIG_ENV_SIZE'
undeclared here (not in a function); did you mean 'CONFIG_CMD_XIMG'?
#define ENV_SIZE (CONFIG_ENV_SIZE - ENV_HEADER_SIZE)
So, fix consists of changing the order of include files
in serial_sifive.c to include first common.h file.
Cc: Anup Patel <Anup.Patel@wdc.com>
Cc: Rick Chen <rick@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Like clk_get_by_index, there is requirement for
clk_get_by_index_nodev. In this case to make common
code functionalities for dev and nodev, clk_get_by_index
is trying to get the index of clock by passing ofnode
instead of actual dev like current gpio uclass does.
In these scenarios with current order of include files
the fu540-prci driver is unable to find CONFIG_ENV_SIZE.
In file included from arch/riscv/include/asm/u-boot.h:23:0,
from include/dm/of.h:10,
from include/dm/ofnode.h:12,
from include/clk.h:11,
from include/clk-uclass.h:13,
from drivers/clk/sifive/fu540-prci.c:32:
include/environment.h:145:19: error: 'CONFIG_ENV_SIZE'
undeclared here (not in a function); did you mean 'CONFIG_CMD_XIMG'?
#define ENV_SIZE (CONFIG_ENV_SIZE - ENV_HEADER_SIZE)
So, fix consists of changing the order of include files
in fu540-prci.c to include first common.h file.
Cc: Anup Patel <Anup.Patel@wdc.com>
Cc: Rick Chen <rick@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Like clk_get_by_index, there is requirement for
clk_get_by_index_nodev. In this case to make common
code functionalities for dev and nodev, clk_get_by_index
is trying to get the index of clock by passing ofnode
instead of actual dev like current gpio uclass does.
In these scenarios with current order of include files
the atcspi200_spi driver is unable to find CONFIG_ENV_SIZE.
In file included from arch/nds32/include/asm/u-boot.h:24,
from include/dm/of.h:10,
from include/dm/ofnode.h:12,
from include/clk.h:11,
from drivers/spi/atcspi200_spi.c:9:
include/environment.h:145:19: error: 'CONFIG_ENV_SIZE'
undeclared here (not in a function); did you mean 'CONFIG_CMD_XIMG'?
#define ENV_SIZE (CONFIG_ENV_SIZE - ENV_HEADER_SIZE)
So, fix consists of changing the order of include files
in atcspi200_spi.c to include first common.h file.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Only some Soc need Schmitter feature, so move the
implementation into their own files.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
As the mux/pull/drive feature implement at own file,
the type and label are not necessary.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
RK3288 pmu_gpio0 pull setting have no higher 16 writing corresponding
bits, need to read before write the register.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
As the common set_mux func(), implement the feature at the own file
for each Soc.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
RK3288 pmu_gpio0 drive strength setting have no higher 16 writing
corresponding bits, need to read before write the register.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
As the common set_mux func(), implement the feature at the own file
for each Soc.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
RK3288 pmu_gpio0 iomux setting have no higher 16 writing corresponding
bits, need to read before write the register.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Such as rk3288's pins of pmu_gpio0 are a special feature, which have no
higher 16 writing corresponding bits, use common set_mux() func would
introduce more code, so implement their set_mux() in each Soc's own
file to reduce the size of code.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Some files have the redundant spaces, remove them.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>