Flushing L3 cache may need variable time depending upon cache line
allocation.
Coming up with a proper timeout value would be best handled by
simulations under multiple scenarios in your actual system.
>From the purely HN-F point of view, the flush would take ~15 cycles for
a clean line, and ~22 cycles for a dirty line. For the dirty line case,
there are many variables outside the HN-F that will increase the
duration per line. For example, a *DBIDResp from the SN-F/SBSX,
memory controller latency, SN-F/SBSX RetryAck responses, CCN ring
congestion, CCN ring hops, etc, etc. The worst-case timeout would
have to factor in all of these variables plus the HN-F cycles for
every line in the L3, and assuming all lines are dirty
In case if L3 is not flushed properly, system behaviour will be
erratic, so remove timeout and add loop to check status of L3 cache.
System will stuck in while loop if there is some issue in L3 cache
flushing.
Signed-off-by: Udit Kumar <udit.kumar@nxp.com>
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Layerscape began to use two eSDHC controllers, for example,
LS1028A. They are same IP block with same reference clock.
This patch is to add clock support for the second eSDHC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Rx Compliance tests may fail intermittently at high jitter
frequencies using default register values.
So program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Enable workaround for USB erratum A-008997. Here PCSTXSWINGFULL
registers has been moved to DSCR as compared to other Layerscape SoCs
where it was in SCFG.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
In initf_bootstage() we call bootstage_mark_name() which ends up calling
timer_get_us() before timer_init(); that cause crash for stm32mp1.
This patch solve the issue without changing the initialization sequence.
See also commit 97d20f69f5 ("Enable CONFIG_TIMER_EARLY with bootstage")
for other solution when DM is activated for TIMER.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
ENVL_NOWHERE is dependent on CONFIG_ENV_IS_NOWHERE and not on
CONFIG_CHAIN_OF_TRUST so return ENVL_NOWHERE when CONFIG_ENV_IS_NOWHERE
is enabled
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
LS1028A is an ARMv8 implementation. LS1028ARDB is an evaluation
platform that supports the LS1028A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The LX2160A PCIe is using driver PCIE_LAYERSCAPE_GEN4 instead
of PCIE_LAYERSCAPE.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The lx2160a have up to 6 PCIe controllers and have different
address and size of PCIe region.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Change to use PCIe address macro to determine if precompile the PCIe
MMU table entry.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
According to De Morgan's Law[1]:
!(A && B) = !A || !B
!(A || B) = !A && !B
There are 5 places in the code where we find:
#if !(defined(CONFIG_SYS_ICACHE_OFF) && defined(CONFIG_SYS_DCACHE_OFF))
and 4 places in the code where we find:
#if (!defined(CONFIG_SYS_ICACHE_OFF) || !defined(CONFIG_SYS_DCACHE_OFF))
In words, the construct:
!defined(CONFIG_SYS_[DI]CACHE_OFF)
means:
"is the [DI]CACHE on?"
and the construct:
defined(CONFIG_SYS_[DI]CACHE_OFF)
means:
"is the [DI]CACHE off?"
Therefore
!(defined(CONFIG_SYS_ICACHE_OFF) && defined(CONFIG_SYS_DCACHE_OFF))
means:
"the opposite of 'are they both off?'"
in other words:
"are either or both on?"
and:
(!defined(CONFIG_SYS_ICACHE_OFF) || !defined(CONFIG_SYS_DCACHE_OFF)
means:
"are either or both on?"
As a result, I've converted the 4 instances of '(!A || !B)' to '!(A && B)' for
consistency.
[1] https://en.wikipedia.org/wiki/De_Morgan%27s_laws
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
This is fix to:
e2a12f590d rockchip: use 'arch-rockchip' as header file path
The V2 of origin patch set has fix this, but we merge V1 by
mistake, so lets correct it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
This fixes SPL linker script size checks for 3 lds files where the size
checks were implemented as "x < YYY_MAX_SIZE".
Fix the size checks to be "x <= YYY_MAX_SIZE" instead.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
On AM654 SoC(arm64) which is IO coherent and has L3 Cache, cache
maintenance operations being done to support non-coherent platforms
causes issues.
For example, here is how U-Boot prepares/handles a buffer to receive
data from a device (DMA Write). This may vary slightly depending on the
driver framework:
Start DMA to write to destination buffer
Wait for DMA to be done (dma_receive()/dma_memcpy())
Invalidate destination buffer (invalidate_dcache_range())
Read from destination buffer
The invalidate after the DMA is needed in order to read latest data from
memory that’s updated by DMA write. Also, in case random prefetch has
pulled in buffer data during the “wait for DMA” before the DMA has
written to it. This works well for non-coherent architectures.
In case of coherent architecture with L3 cache, DMA write would directly
update L3 cache contents (assuming cacheline is present in L3) without
updating the DDR memory. So invalidate after “wait for DMA” in above
sequence would discard latest data and read will cause stale data to be
fetched from DDR. Therefore invalidate after “wait for DMA” is not
always correct on coherent architecture.
Therefore, provide a Kconfig option to disable cache maintenance ops on
coherent architectures. This has added benefit of improving the
performance of DMA transfers as we no longer need to invalidate/flush
individual cache lines(especially for buffer thats several KBs in size).
In order to facilitate use of same Kconfig across different
architecture, I have added the symbol to top level arch/Kconfig file.
Patch currently disables cache maintenance ops for arm64 only.
flush_dcache_all() and invalidate_dcache_all() are exclusively used
during enabling/disabling dcache and hence are not disabled.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
rockchip platform header file is in 'arch-rockchip'
instead of arch-$(SOC) for all SoCs.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The match controller register is not cleared during
initialization. However, some bits of this register may reset the TC if
tnMRx match it.
As we can't make any assumption about how U-Boot is launched by the first
stage bootloader (such as S1L) clearing this register ensure that the
timers work as expected.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This fixes relaction isses with the PSCI_TABLE entries in
the psci_32_table and psci_64_table.
When using 32-bit adress pointers relocation was not being applied to
the tables, causing PSCI handlers to point to the un-relocated code
area. By using 64-bit data relocation is properly applied. The
handlers are thus in the "secure data" area, which is protected by
/memreserve/ in the FDT.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
HVC call makes use of 6 mandatory arguments rather than 7 in the same way
as SMC calls. The 7th argument is optional (Client ID) for both HVC and
SMC but is implemented as 16-bit parameter and register R7 or W7. The aim
of this patch is just fix compilation error due to an invalid asm code in
the HVC call so that's why the 7th argument is removed.
The issue does not report any error in a normal build as hvc_call is not
used at all and is optimized by the compiler. Using -O0 triggers the
error so the patch is intended to fix issues on a ongoing effor to build
U-Boot with -O0.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
When PSCI is enabled, we are expecting U-Boot which now act
as EL3 software will handle all the PSCI calls. We won't need
fwcall as no further HVC or SMC are needed.
Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
Allow PSCI layer to handle any SiP service functions added by
platform vendors. PSCI layer will look for SiP service function
in the SiP function table located in '._secure_svc_tbl_entries'
section if the SMC function identifier is not found in the PSCI
standard functions table. Use DECLARE_SECURE_SVC macro to declare
and add platform specific SiP service function.
This new section '._secure_svc_tbl_entries' is located next to
'._secure.text' section. Refer to arch/arm/cpu/armv8/u-boot.lds.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
This code allows reusing the default u-boot as in the late board init, the
default envs are restored and proper recovery scripts executed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The proposed way of reading fused MAC in the imx_get_mac_from_fuse() may
be different for other boards.
This commit defines the imx_get_mac_from_fuse() as a weak function to allow
board file overriding it with customized function.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Provide function to enable I2C clocks for vf610 - in the generic code.
This function overrides the default weak function implementation (which
only returns 1).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Commit 1416e2d225 ("armv8: make SPL exception vectors optional") had a
typo in it which effectively disabled exception handling in SPL code always.
Since nobody complained, I guess we may as well disable exception handling
in SPL always by default.
So fix the bug to make the config option effective, but disable exception
handling in SPL by default. This gets us to the same functionality as before
by default, but with much less code included in the binary.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Barrier transactions from CCI400 need to be disabled till
the DDR is configured, otherwise it may lead to system hang.
The patch adds workaround to fix the erratum.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The SEC QI ICID setup in the QIIC_LS register is actually an offset
that is being added to the ICID coming from the qman portal. Setting
it with a non-zero value breaks SMMU setup as the resulting ICID is
not known. On top of that, the SEC QI ICID must match the qman portal
ICIDs in order to share the isolation context.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
remove SCSI and SCSI_AHCI configs for ls1043ardb due to no sata interface
support.
this changed is to fixed the ls1043ardb compile warning as fallows:
===================== WARNING ======================
This board does not use CONFIG_DM_SCSI. Please update
the storage controller to use CONFIG_DM_SCSI before the
v2019.07 release. Failure to update by the deadline may
result in board removal.See doc/driver-model/MIGRATION.txt
for more info.
====================================================
Signed-off-by: Peng Ma <peng.ma@nxp.com>
[PK: reword the patch subject]
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Moves FSL_TZASC_400 and FSL_TZPC_BP147 configs to Kconfig
for LS1088A and LS2088A platforms.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
LX2160AQDS is a development board that supports LX2160A
family SoCs. This patch add base support for this board.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[PK: Sqaush patch for "secure boot defconfig" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
some dpmacs in armv8a based freescale layerscape SOCs can be
configured via both serdes(sgmii, xfi, xlaui etc) bits and via
EC*_PMUX(rgmii) bits in RCW.
e.g. dpmac 17 and 18 in LX2160A can be configured as SGMII from
serdes bits and as RGMII via EC1_PMUX/EC2_PMUX bits
Now if a dpmac is enabled by serdes bits then it takes precedence
over EC*_PMUX bits. i.e. in LX2160A if we select serdes protocol
that configures dpmac17 as SGMII and set the EC1_PMUX as RGMII,
then the dpmac is SGMII and not RGMII.
Therefore, move the fsl_rgmii_init after fsl_serdes_init. in
fsl_rgmii_init function of SOC, we will check if the dpmac is enabled
or not? if it is (fsl_serdes_init has already enabled the dpmac), then
don't enable it.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add code to initial ethernet interface arrays
with corresponding dpmac-id values in serdes_init function
for LX2160A.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Commit 81ea00838c ("efi_loader: PSCI reset and shutdown") put the SMCCC
assembly code into the efi specific code section. This is wrong when we
do not have EFI_LOADER enabled, as that strips efi runtime sections from
the output binary
Reported-by: Michal Simek <monstr@monstr.eu>
Reported-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Tested-by: Michal Simek <monstr@monstr.eu>
Fixes: 81ea00838c ("efi_loader: PSCI reset and shutdown")
Signed-off-by: Alexander Graf <agraf@suse.de>
Refactor the switch from supervisor to hypervisor to a new function called
at the beginning of do_bootefi().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Make use of "IMAGE_MAX_SIZE" and "IMAGE_TEXT_BASE" rather than
CONFIG_SPL_MAX_SIZE and CONFIG_SPL_TEXT_BASE. This lets us re-use the
same script for both SPL and TPL. Add logic to scripts/Makefile.spl to
pass in the right value when preprocessing the script.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850evm & omap3_logic_somlv
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Similar changes was done for Zynq in past and this patch just follow
this pattern to separate cpu code from SoC code.
Move arch/arm/cpu/armv8/zynqmp/* -> arch/arm/mach-zynqmp/*
And also fix references to these files.
Based on
"ARM: zynq: move SoC sources to mach-zynq"
(sha1: 0107f24036)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is hard dependency for CLK_ZYNQMP to have zynqmp_pmufw_version()
but also FPGA code is calling this function which is possible to use
without actual CLK_ZYNQMP firmware driver to be enabled.
This patch enables the case where only fixed-clock CLK setup is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
On LS1043A rev1.0 there are 4 interrupt pins for INTx, and on
rev1.1 there is only 1 for INTx, so the current fixup is inverse
of the fact.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1043A/LS1023A 23x23 package silicon has different SVR:VAR_PER.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls2088ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- remove EL3 specific erratas for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1088ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- MC address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- ifc chip select changes for TFABOOT
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Fixes for TFABOOT framework
- update eMMC bootsrc to SD_MMC
- Increase buffer size for mcinitcmd from 256 to 512
- Fix mcinitcmd and bootcmd for Secure Boot
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add Kconfig option WATCHDOG_RESET_DISABLE to disable watchdog reset
in imx_watchdog driver, so that the watchdog will not be fed in
u-boot if CONFIG_WATCHDOG_RESET_DISABLE is enabled.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Support watchdog driver for fsl-lsch2. It's disabled in default.
If you want to use it, please enable CONFIG_IMX_WATCHDOG.
Define CONFIG_WATCHDOG_TIMEOUT_MSECS to set watchdog timeout.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
NXP layerscape architecture Chassis 3.2 builds upon chassis3
architecture with changes like DDR Memory map change,
removal of IFC and support of upto 8 I2C controller.
Patch add README.lsch3_2 and the above changes under
macro CONFIG_NXP_LSCH3_2.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Some lsch3 based SoCs like lx2160a contains three
serdes modules.
Add support for third serdes protocol in lsch3
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support of MC framework for TFA
Make MC framework independent of boot source.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Returns job ring status as true in TFABOOT, as one job ring is always
reserved.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Changes the el2_to_aarch32 SMC ID from 0xc000ff04 to 0xc200ff17,
it is applicable to both TFA and non-TFA boot.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Workaround of erratum A010539 clears the RCW source field in PORSR1
register, causing failure of detecting boot source using this method.
Use SMC call if U-Boot runs at EL2. If SMC is not implemented or
running at EL3, continue to read PORSR1 and presume QSPI as boot
source if erratum workaround A010539 is enabled and RCW source is
cleared.
Signed-off-by: York Sun <york.sun@nxp.com>
OCRAM initialization is performed by TFA, Hence
skipped from u-boot.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Adds SMC calls for getting DDR size and bank info for TFABOOT.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Removes EL3 specific erratas for TFABOOT, And now taken care in TFA.
ARM_ERRATA_855873, SYS_FSL_ERRATUM_A008850, SYS_FSL_ERRATUM_A008511,
SYS_FSL_ERRATUM_A008336, SYS_FSL_ERRATUM_A009663,
SYS_FSL_ERRATUM_A009803, SYS_FSL_ERRATUM_A009942,
SYS_FSL_ERRATUM_A010165
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
PORSR register holds the cfg_rcw_src field which can be used
to identify boot source.
Further, it can be used to select the environment location.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[YS: fix multiple checkpatch issues]
Reviewed-by: York Sun <york.sun@nxp.com>
Adds TFABOOT support config option and add generic code to enable
execution from DDR.
Signed-off-by: York Sun <york.sun@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Change tlb base address from OCRAM to DDR when exception level is
less than 3.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In case SError happens at EL2, if SCR_EL3[EA] is not routing it to
EL3, and SCR_EL3[RW] is set to aarch64, setting HCR_EL2[AMO] routes
the exception to EL2. Otherwise this exception is not taken.
Signed-off-by: York Sun <york.sun@nxp.com>
Move static definitions to cpu.c file, as it doesn't allow
the cpu.h file to be included in multiple c files.
Signed-off-by: York Sun <york.sun@nxp.com>
When an operating system started via bootefi tries to reset or power off
this is done by calling the EFI runtime ResetSystem(). On most ARMv8 system
the actual reset relies on PSCI. Depending on whether the PSCI firmware
resides the hypervisor (EL2) or in the secure monitor (EL3) either an HVC
or an SMC command has to be issued.
The current implementation always uses SMC. This results in crashes on
systems where the PSCI firmware is implemented in the hypervisor, e.g.
qemu-arm64_defconfig.
The logic to decide which call is needed based on the device tree is
already implemented in the PSCI firmware driver. During the EFI runtime
the device driver model is not available. But we can minimize code
duplication by merging the EFI runtime reset and poweroff code with
the PSCI firmware driver.
As the same HVC/SMC problem is also evident for the ARMv8 do_poweroff
and reset_misc routines let's move them into the same code module.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Some erratum workarounds call into C code before the stack
is setup, this can lead to values pushed onto the stack
being lost, firewall exceptions, and other undefined behavior.
Setup a temporary stack to allow these functions to work
correctly.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Allow platform vendors to handle SError interrupt exceptions from
ARMv8 PSCI exception vectors by overriding this weak function
'plat_error_handler'.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
The option has never existed and config whitelist script accumulates
it from a comment block, wipe it out from the source code.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The explicit arch specific build symbol allows to group supported
boards, generalize common config options and it will serve as
a dependency for platform only drivers.
Two related board defconfigs are resynced after the change.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
This patch adds new zynqmp command "zynqmp tcminit mode" to
initialize TCM. TCM needs to be initialized before accessing
to avoid ECC errors. This new command helps to perform
the same. It also makes tcm_init() as global and uses it for
doing the TCM initialization.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moves TCM initialization to a separate routine to
make it modular and can be reused if required. It also prints
warning message now as it writes to TCM.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The interruption support had be removed for ARM architecture and
the function get_timer_masked() is no more used except in some
the timer.c files.
This patch clean each timer.c which implement this function and
remove the associated prototype in u-boot-arm.h
For timer.c, I don't verify if the weak version of get_timer
(in lib/time.c) can be used
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The interruption support had be removed for ARM architecture and
the function udelay_masked() is no more used except in some timer.c
files and have the same content than udelay() or __udelay().
This patch update each timer.c implementing this function and
remove the associated prototype in u-boot-arm.h.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XRFI
-----END PGP SIGNATURE-----
Merge tag 'fsl-qoriq-for-v2018.11-rc1' of git://git.denx.de/u-boot-fsl-qoriq
Switch to driver model for eSDHC on Layerscape SoCs including LS1021A,
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
Reuse the existing ICID setup code done for LS1046A smmu enablement
and add the equivalent setup for LS1043A chips.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
At present the MMC subsystem maintains its own list of MMC devices.
This cannot work with driver model when CONFIG_BLK is enabled, use
blk_dread to replace previous mmc read interface, use
mmc_get_blk_desc to get the mmc device property.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
[York S: reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
A lot of goodness in this release. We're *very* close to running the
UEFI Shell and SCT natively. The only missing piece are HII protocols.
- FAT write support (needed for SCT)
- improved FAT directory support (needed for SCT)
- RTC support with QEMU -M virt
- Sandbox support (run UEFI binaries in Linux - yay)
- Proper UTF-16 support
- EFI_UNICODE_COLLATION_PROTOCOL support (for UEFI Shell)
- EFI_SIMPLE_TEXT_INPUT_EX_PROTOCOL support (for UEFI Shell)
- Fix window size determination
- Fix Tegra by explicitly unmapping RAM
- Clean up handle entanglement
- Lots of generic code cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ZuJG
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-09-26
A lot of goodness in this release. We're *very* close to running the
UEFI Shell and SCT natively. The only missing piece are HII protocols.
- FAT write support (needed for SCT)
- improved FAT directory support (needed for SCT)
- RTC support with QEMU -M virt
- Sandbox support (run UEFI binaries in Linux - yay)
- Proper UTF-16 support
- EFI_UNICODE_COLLATION_PROTOCOL support (for UEFI Shell)
- EFI_SIMPLE_TEXT_INPUT_EX_PROTOCOL support (for UEFI Shell)
- Fix window size determination
- Fix Tegra by explicitly unmapping RAM
- Clean up handle entanglement
- Lots of generic code cleanup
[trini: Fixup merge conflict in include/configs/qemu-arm.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
Modify the zynqmp_pmufw_version() routine to return PMUFW version so
that it can be reused wherever required. Get PMUFW version from PMU
only once at bootup and later just return stored value.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moves the PM version related macros to .h file so that
they can be reused in other files.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
SPI controllers SSP1, 2 and 3 require to enable their respective clocks.
Let's enable them only when the SPI controller driver is built.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Use CONFIG_IS_ENABLED(EFI_LOADER) to avoid explicitly checking CONFIG_SPL
too. This simplifies the conditional.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
There are multiple GPIOs that can be used with the same driver depending
on the CONFIG_GPIO_BASE defined in the controller driver.
GPIO3 and 4 require a clock to be enabled so let's enable them when the
driver is built.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Four different boards had different options for enabling cache
that were virtually all the same. This consolidates these
common functions into arch/arm/cpu/arm926ejs/cache.c
This also has the positive side-effect of enabling cache on
the Davinci (da850) boards.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Add mach-at91 to the list of consolidations]
Signed-off-by: Tom Rini <trini@konsulko.com>
In commit a1274cc94a ("ARM: Page align secure section only when it is
executed in situ"), we used output section attributes (the "ALIGN"
keyword after the colon) to specify the alignment requirements. Using
the constant "COMMONPAGE" there was recently broken in binutils 2.31 [1].
Binutils maintainer Alan Modra suggested the former method would still
work. Since both methods achieve the same result, this patch does just
that. This fixes the "reboot after bootm" issue we've been seeing on
sunxi when booting non-secure.
[1] https://sourceware.org/bugzilla/show_bug.cgi?id=23571
Suggested-by: Alan Modra <amodra@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Update README.falcon to use "none" for compression property for
ramdisk image to avoid being uncompressed upon loading.
Signed-off-by: York Sun <york.sun@nxp.com>
Program Central Security Unit (CSU) to grant access to USB 2.0
controller.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: rewrite commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for SEC ICID configuration and apply it for ls1046a.
Also add code to make the necessary device tree fixups.
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for ICID setting of fman ports and the required device
tree fixups.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for ICID setting of qman portals and the required device
tree fixups. Also fix an endiness issue in portal setup code.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add infrastructure for ICID setup and device tree fixup on ARM
platforms. This include basic ICID setup for several devices.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In ft_fixup_enet_phy_connect_type(), use strlen() instead of sizeof()
on the pointer result of phy_string_for_interface(). sizeof() was
returning the size of the pointer (4 bytes), resulting in the
phy-connection-type being set to "rgmi" rather than "rgmii-id".
Signed-off-by: Brendan Shanks <brendan.shanks@teradek.com>
Cc: York Sun <york.sun@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Even though the exception vector table is a fundamental part of the ARM
architecture, U-Boot mostly does not make real use of it, except when
crash dumping. But having it in takes up quite some space, partly due to
the architectural alignment requirement of 2KB. Since we don't take special
care of that, the compiler adds a more or less random amount of padding
space, which increases the image size quite a bit, especially for the SPL.
On a typical Allwinner build this is around 1.5KB of padding, plus 1KB
for the vector table (mostly padding space again), then some extra code
to do the actual handling. This amounts to almost 10% of the maximum image
size, which is quite a lot for a pure debugging feature.
Add a Kconfig symbol to allow the exception vector table to be left out
of the build for the SPL.
For now this is "default y" for everyone, but specific defconfigs,
platforms or .config files can opt out here at will, to mitigate the code
size pressure we see for some SPLs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The arm64 exception handling code is quite big, mostly due to
architectural alignment requirements. Each exception entry spans 32
instructions, which sounds generous, but is too small to fit all of the
save/branch/restore code in there. So at the moment we use only four
instructions, branching into shared save and restore routines.
To not leave the space for those remaining 28 instructions wasted, let's
split the save and restore routines and stuff them into the gaps.
This saves about 250 bytes of code, which is helpful for those tight
SPLs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ePTT
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-07-25
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
Another round of sorting Kconfig entries aplhabetically.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
The include/phy.h will start including dm.h, which pulls in
linux/compat.h after the attempted redefinition in
arch/arm/include/asm/armv8/mmu.h, so move this include to allow
redefinition.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
A new defconfig is introduced to support SPL boot from QSPI NOR
flash. This is to support falcon mode for faster booting into
Linux.
Signed-off-by: York Sun <york.sun@nxp.com>
Remove the old implementation in order to enable DM for sata.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Enable I-cache for SPL boot to boost performance. Earlier MMU was
enabled only for LS2080A and has since been dropped by commit
f539c8a4a7 ("armv8: ls2080a: Drop early MMU for SPL build").
Signed-off-by: York Sun <york.sun@nxp.com>
Some times gcc may generate data that is then used within code that may
be part of an efi runtime section. That data could be jump tables,
constants or strings.
In order to make sure we catch these, we need to ensure that gcc emits
them into a section that we can relocate together with all the other
efi runtime bits. This only works if the -ffunction-sections and
-fdata-sections flags are passed and the efi runtime functions are
in a section that starts with ".text".
Up to now we had all efi runtime bits in sections that did not
interfere with the normal section naming scheme, but this forces
us to do so. Hence we need to move the efi_loader text/data/rodata
sections before the global *(.text*) catch-all section.
With this patch in place, we should hopefully have an easier time
to extend the efi runtime functionality in the future.
Signed-off-by: Alexander Graf <agraf@suse.de>
[agraf: Fix x86_64 breakage]
ARMV7_LPAE is required in order to enable the MMU in HYP mode.
And we really want to enable the MMU in HYP mode such that we can
enable the the caches. Otherwise U-Boot code (such as the EFI
implementation) that runs in HYP mode will run at a snils pace.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The current code that switches into HYP mode doesn't bother to set
up a stack for HYP mode. This doesn't work for EFI applications
as they expect a usable stack. Fix this by migrating the stack
pointer from SP_svc to SP_hyp while in Monitor mode.
This restores the stack pointer when we drop into HYP mode.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
A proper stack is required to safely use C code in psci_arch_cpu_entry.
Fixes: 486daaa618 ("arm: psci: add a weak function psci_arch_cpu_entry")
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Patrick DELAUNAY <Patrick.delaunay@st.com>
Tested-by: Patrick DELAUNAY <Patrick.delaunay@st.com>
The Allwinner A64 SoCs suffers from an arch timer implementation erratum,
where sometimes the lower 11 bits of the counter value erroneously
become all 0's or all 1's [1]. This leads to sudden jumps, both forwards and
backwards, with the latter one often showing weird behaviour.
Port the workaround proposed for Linux to U-Boot and activate it for all
A64 boards.
This fixes crashes when accessing MMC devices (SD cards), caused by a
recent change to actually use the counter value for timeout checks.
Fixes: 5ff8e54888 ("sunxi: improve throughput
in the sunxi_mmc driver")
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2018-May/576886.html
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Tested-by: Guillaume Gardet <guillaume.gardet@free.fr>
At the moment we have the workaround for the Freescale arch timer
erratum A-008585 merged into the generic timer_read_counter() routine.
Split those two up, so that we can add other errata workaround more
easily. Also add an explaining comment on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Tested-by: Guillaume Gardet <guillaume.gardet@free.fr>
As recommended by Arm in [1], ACTLR[0] (Enable invalidates of BTB)
needs to be set[2] for BTB to be invalidated on ICIALLU. This needs to
be done unconditionally for Cortex-A15 processors. Provide a config
option for platforms to enable this option based on impact analysis
for products.
NOTE: This patch in itself is NOT the final solution, this requires:
a) Implementation of v7_arch_cp15_set_acr on SoCs which may not
provide direct access to ACR register.
b) Operating Systems such as Linux to provide adequate workaround in the
right locations.
c) This workaround applies to only the boot processor. It is important
to apply workaround as necessary (context-save-restore) around low
power context loss OR additional processors as necessary in either
firmware support OR elsewhere in OS.
[1] https://developer.arm.com/support/security-update
[2] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0438c/BABGHIBG.html
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Andre Przywara <Andre.Przywara@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
As recommended by Arm in [1], IBE[2] has to be enabled unconditionally
for BPIALL to be functional on Cortex-A8 processors. Provide a config
option for platforms to enable this option based on impact analysis
for products.
NOTE: This patch in itself is NOT the final solution, this requires:
a) Implementation of v7_arch_cp15_set_acr on SoCs which may not
provide direct access to ACR register.
b) Operating Systems such as Linux to provide adequate workaround in the right
locations.
c) This workaround applies to only the boot processor. It is important
to apply workaround as necessary (context-save-restore) around low
power context loss OR additional processors as necessary in either
firmware support OR elsewhere in OS.
[1] https://developer.arm.com/support/security-update
[2] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0344k/Bgbffjhh.html
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Andre Przywara <Andre.Przywara@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
cpu_cmd() is reading cpu number via simple_strtoul() which is always
unsigned type.
Platform code implementations are not expecting that nr can be negative
and there is not checking in the code for that too.
This patch is using u32 type for cpu number to make sure that platform
code get proper value range.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If many values differ from the defaults, overriding the full table
is simpler and more space efficient than tweaking it through
mxs_adjust_memory_params().
Signed-off-by: Mans Rullgard <mans@mansr.com>
There should be return value check from zynqmp_mmio_read() in
zynqmp_mmio_rawwrite() to make sure that errors are propagated properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We currently handle the UEFI runtime reset / power off case handling via
a switch statement. Compilers (gcc in my case) may opt to handle these via
jump tables which they may conveniently put into .rodata which is not part
of the runtime section, so it will be unreachable when executed.
Fix this by just converting the switch statement into an if/else statement.
It produces smaller code that is faster and also correct because we no
longer refer .rodata from efi runtime code.
Reported-by: Andreas Färber <aferber@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
FRWY-LS1012A belongs to LS1012A family with features 2 1G SGMII PFE
MAC, Micro SD, USB 3.0, DDR, QuadSPI, Audio, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
[yorks: rebase and fix SPDX tag]
[yorks: fix board/freescale/ls1012afrdm/Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
PPA firmware and header address may vary depending upon different
boards, configure ppa firmware and header address in board specific
Kconfig.
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The UEFI spec mandates that unaligned memory access should be enabled if
supported by the CPU architecture.
This patch implements the function unaligned_access() to reset the aligned
access flag in the system control register (SCTLR). It is called when the
bootefi command is invoked.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: fix SPDX identifier]
Signed-off-by: Alexander Graf <agraf@suse.de>
Existing EEMI version is to as 1.0 (available from xilinx v2018.1
version). Update required API version to match with EEMI API version.
New PMUFW version is required for operations with programmable logic.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP emulation platforms are no longer tested and supported that's why
remove macros and code around.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- The correct way to build with thumb mode is to select SYS_THUMB_BUILD
- We should be setting -march=armv7-m in arch/arm/Makefile not the
sub-config.mk file.
Signed-off-by: Tom Rini <trini@konsulko.com>
microblaze:
- Align defconfig
zynq:
- Rework fpga initialization and cpuinfo handling
zynqmp:
- Add ZynqMP R5 support
- Wire and enable watchdog on zcu100-revC
- Setup MMU map for DDR at run time
- Show board info based on DT and cleanup IDENT_STRING
zynqmp tools:
- Add read partition support
- Add initial support for Xilinx bif format for boot.bin generation
mmc:
- Fix get_timer usage on 64bit cpus
- Add support for SD3.0 UHS mode
nand-zynq:
- Add support for 16bit buswidth
- Use address cycles from onfi params
scsi:
- convert ceva sata to UCLASS_AHCI
timer:
- Add Cadence TTC for ZynqMP r5
watchdog:
- Minor cadence driver cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlr1ldMACgkQykllyylKDCHioACghoJw6+NqsZXl8zGWRP38yZ5K
mvgAnihfOQq125mpKPZmcc5yt6wVwYIU
=8ji9
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.07' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2018.07
microblaze:
- Align defconfig
zynq:
- Rework fpga initialization and cpuinfo handling
zynqmp:
- Add ZynqMP R5 support
- Wire and enable watchdog on zcu100-revC
- Setup MMU map for DDR at run time
- Show board info based on DT and cleanup IDENT_STRING
zynqmp tools:
- Add read partition support
- Add initial support for Xilinx bif format for boot.bin generation
mmc:
- Fix get_timer usage on 64bit cpus
- Add support for SD3.0 UHS mode
nand-zynq:
- Add support for 16bit buswidth
- Use address cycles from onfi params
scsi:
- convert ceva sata to UCLASS_AHCI
timer:
- Add Cadence TTC for ZynqMP r5
watchdog:
- Minor cadence driver cleanup
This patch fills the MMU map for DDR at run time based on information read
from Device Tree or automatically detected from static configuration.
The patch is needed because for systems which has for example 1GB of memory
but MMU map is 2GB there could be spurious accesses which was seen in past
when mapping is not fitting with actual memory installed.
Signed-off-by: Nitin Jain <nitin.jain@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mask HRESET_B after cleared the the RCW_SRC, because in the workaround
we override the RCW_SRC and if HRESET_B is issued after the override
then SoC cannot find valid RCW as the RCW_SRC was overwritten and
result in hang. So we need to mask HRESET_B in case user asserts it,
and the PORESET_B should be asserted which leads to resampling of
cfg_rcw_src pins and loading of correct RCW_SRC.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Enable support for multiple loadable images in SEC firmware FIT image.
Also add example "sec_firmware_ppa.its" file.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
JR3 was getting removed from device tree only if random number
generation was successful. However, if SEC firmware is present,
JR3 should be removed from device tree node irrespective of the
random seed generation as SEC firmware reserves it for it's use.
Not removing it in case of random number generation failure causes
the kernel to crash.
Random number generation was being called twice. This is not
required. If SEC firmware is running, SIP call can be made to the SEC
firmware to get the random number. This call itself would return
failure if function is not supported. Duplicate calling of random
number generation function has been removed.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TZASC controller configurations are similar. Put them in a macro and
avoid code duplication.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Cache maintenance procedure is same for v7A and v7R
processors. So re-use cache-cp15.c file except for
mmu parts.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Memory Protection Unit(MPU) allows to partition memory into regions
and set individual protection attributes for each region. In absence
of MPU a default map[1] will take effect. Add support for configuring
MPU on Cortex-R, by reusing the existing support for Cortex-M processor.
[1] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0460d/I1002400.html
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Cortex-R* processors are a mid-range CPUs for use in deeply-embedded,
real-time systems. It implements the ARMv7-R architecture, and includes
Thumb-2 technology for optimum code density and processing throughput.
Except for MPU(Memory Protection Unit) and few CP15 registers, most of the
features are compatible with v7 architecture. So,reuse the same armv7
folder and introduce a new config CPU_V7R in order to differentiate
from v7 based platforms.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Currently CPU_V7 kconfig symbol supports only ARMv7A architectures under
armv7 folder. This led to a misconception of creating separate folders
for armv7m and armv7r. There is no reason to create separate folder for
other armv7 based architectures when it can co-exist with few Kconfig
symbols.
As a first step towards a common folder, rename CPU_V7 as CPUV7A. Later
separate Kconfig symbols can be added for CPU_V7R and CPU_V7M and
can co exist in the same folder.
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Suggested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Not all ARM V7 based cpus has VBAR for remapping
vector base address. So, update VBAR only if it available.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This function is no more used, and replaced by psci_save
which save also context id as requested by PSCI requirements.
Even if the context id is not used by Linux, it should be saved
and restored in r0 when the CPU_ON is performed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The added function psci_arch_cpu_entry() is called
during psci_cpu_entry() and can be used by arch to handle
PSCI state transition from ON_PENDING to ON.
The default weak function is empty: not behavior change.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Save and use the 3rd parameter of PSCI CPU_ON request: context_id.
The context_id parameter is only meaningful to the caller.
U-Boot PSCI preserves a copy of the value passed in this parameter.
Following wakeup from a powerdown state, U-BOOT PSCI places
this value in R0 when it first enters the OS.
NB: this context id is not (yet?) used by Linux but it is mandatory
to be PSCI compliant.
update armv7 psci functions:
- psci_save_target_pc(): keep for backward compatibility with
current platform (only save PC and force context id to 0)
=> should be removed when all platform migrate to the new API
- psci_save(): new API to use by ARMv7 platform with PSCI,
save pc (= entry_point_address) and context_id
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
