init_tlbs() initialize all the TLB entries required for the system.
So disable DEBUG TLB entry before TLB entries initialization.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
If a variable is used as array subscript, it's valid value range is
0 ... ARRAY_SIZE -1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
There will clear the BSS in the function clear_bss(), the reset address of
the BSS started from the __bss_start, and increased by four-byte increments,
finally stoped depending on the address is equal to the _bss_end. If the end
address __bss_end is not alignment to 4byte, it will be an infinite loop.
1. The reset action stoped depending on the reset address is greater
than or equal the end address of the BSS.
2. The end address of the BSS should be 4byte aligned. Because the reset unit
is 4 Bytes.
This patch is on top of the patch "powerpc/mpc85xx: support application
without resetvec segment in the linker script".
Signed-off-by: Ying Zhang <b40530@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
For SD/SPI 2-stage bootloader, the On-Chip Rom code loads the SPL into L2 SRAM,
then jump to it to begin execution. After that, the SPL loads the final uboot
image into DDR, then jump to it to begin execution. The segment .resetvec in
the SPL and in final U-boot is useless.
So, add new symbols CONFIG_SYS_MPC85XX_NO_RESETVEC for this application.
If CONFIG_SYS_MPC85XX_NO_RESETVEC is set, the segment .resetvec is excluded
and the segment .bootpg is placed in the previous 4K of the segment .text.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Erratum A-006593 is "Atomic store may report failure but still allow
the store data to be visible".
The workaround is: "Set CoreNet Platform Cache register CPCHDBCR0 bit
21 to 1'b1. This may have a small impact on synthetic write bandwidth
benchmarks but should have a negligible impact on real code."
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Calculate reserved fields according to IFC bank count
1. Move csor_ext register behind csor register and fix res offset
2. Move ifc bank count to config_mpc85xx.h to support 8 bank count
3. Guard fsl_ifc.h with CONFIG_FSL_IFC macro to eliminate the compile
error on some devices that does not have IFC controller.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When a T4 board boots from SRIO or PCIE, it needs to finish these processes:
1. Set all the cores in holdoff status.
2. Set the boot location to one PCIE or SRIO interface by RCW.
3. Set a specific TLB entry for the boot process.
4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot.
5. Set a specific TLB entry in order to fetch ucode and ENV from
master.
6. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
7. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
For more information about the feature of Boot from SRIO/PCIE, please
refer to the document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When a b4860qds board boots from SRIO or PCIE, it needs to finish these
processes:
1. Set all the cores in holdoff status.
2. Set the boot location to one PCIE or SRIO interface by RCW.
3. Set a specific TLB entry for the boot process.
4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot.
5. Set a specific TLB entry in order to fetch ucode and ENV from
master.
6. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
7. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
For more information about the feature of Boot from SRIO/PCIE, please
refer to the document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Currently, the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" can enable
the master module of Boot from SRIO and PCIE on a platform. But this
is not a silicon feature, it's just a specific booting mode based on
the SRIO and PCIE interfaces. So it's inappropriate to put the macro
into the file arch/powerpc/include/asm/config_mpc85xx.h.
Change the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" to
"CONFIG_SRIO_PCIE_BOOT_MASTER", remove them from
arch/powerpc/include/asm/config_mpc85xx.h file, and add those macros
in configuration header file of each board which can support the
master module of Boot from SRIO and PCIE.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Freescale documentation presents the PowerPC core names in lower case, such as
"e300", "e500", "e600", etc.
Change the upper case occurrences into lower case so that the core names
reported in U-boot can match the ones from the documentation.
While at it also fix a checkpatch error:
ERROR: space prohibited before that close parenthesis ')'
#53: FILE: arch/powerpc/cpu/mpc86xx/cpu.c:81:
+ printf("e600 Core %d", (msscr0 & 0x20) ? 1 : 0 );
Reported-by: Heinz Wrobel <heinz.wrobel@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
BSC9131RDB is a Freescale Reference Design Board for
BSC9131 SoC which is a integrated device that contains
one powerpc e500v2 core and one DSP starcore.
To support DSP starcore
-Creating LAW and TLB for DSP-CCSR space.
-Creating LAW for DSP-core subsystem M2 memory
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Linker script is not able find start.o binary. So add its absolute path in
u-boot-spl.lds. This change is similar to u-boot-nand.lds
common/Makefile: Avoid compiling unnecssary files
fsl_ifc_spl.c : It is is responsible for reading u-boot binary from
NAND flash and copying into DDR. It also transfer control from NAND SPL
to u-boot image present in DDR.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
IFC errata A003399 is valid for IFC NOR boot i.e.if no on-board NOR flash or
no NOR boot, do not compile its workaround.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
To avoid sign extension problem, use explicit casting to cast
the SDRAM size to type phys_size_t, or else, if the SDRAM size
is 2G(0x80000000), it will be extended to 0xffffffff80000000
when phys_size_t is type 'unsigned long long'.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Accidentally applied an earlier version of the patch, which set
the compatible to "fsl,qoriq-clockgen-2", lacking the final
".0".
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
C99's strict aliasing rules are insane to use in low-level code such as a
bootloader, but as Wolfgang has rejected -fno-strict-aliasing in the
past, add a union so that 16-bit accesses can be performed.
Compile-tested only.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Wolfgang Denk <wd@denx.de>
dcbi instruction has been used to clear D-cache lock. However, the cache
lock is persistent for e6500 core. Use dcblc to clear the lock explicitly.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Boot ROM code creates TLB entries for 3.5G space before entering
the u-boot. Earlier we were deleting these entries after early
initialization of CPU. In recent past, code has been added
to invalidate all these entries before relocation of u-boot code.
So this code to delete TLB entries after CPU initialization
is no longer required.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Acked-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
B4420 is a subset of B4860. Merge them in config_mpc85xx.h to simplify
the defines.
- Removed #define CONFIG_SYS_FSL_NUM_CLUSTERS as this is used nowhere.
- defined CONFIG_SYS_NUM_FM1_10GEC to 0 for B4420 as it does not have 10G.
Also move CONFIG_E6500 out of B4860QDSds.h into config_mpc85xx.h.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Allow DDR clock runs faster than SPD specifes. This may cause memory
failure, but the user should know what is going to happen when using
higher than expected DDR clock.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
To align with chassis generation 2 spec, all cores are numbered in sequence.
The cores may reside across multiple clusters. Each cluster has zero to four
cores. The first available core is numbered as core 0. The second available
core is numbered as core 1 and so on.
Core clocks are generated by each clusters. To identify the cluster of each
core, topology registers are examined.
Cluster clock registers are reorganized to be easily indexed.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T1040 and variants have e5500 cores and are compliant to QorIQ Chassis
Generation 2. The major difference between T1040 and its variants is the
number of cores and the number of L2 switch ports.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T4160 is a subset of T4240. Merge them in config_mpc85xx.h to simplify
the defines. Also move CONFIG_E6500 out of t4qds.h into config_mpc85xx.h.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
"cpu <num> status" should check if core is disabled before printing
the spin table location.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The Freescale MPC8220 Power Architecture processors have long reached
EOL; Freescale does not even list these any more on their web site.
Remove the code to avoid wasting maitaining efforts on dead stuff.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
This gives boards flexibility to assign other than default addresses to each
DDR controller. For example, DDR controler 2 can have 0 as the base and DDR
controller 1 has higher memory.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The workaround has been updated to use a slightly different magic number.
Change from 0x00003000 to 0x30003000.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This is what we have done for the UTMI PHY on P3041/P5020. Then the PHY
initialization can be reused in kernel without “usb start” command.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Removed unused declare serdes_get_prtcl() which was no longer needed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
1, Implemented board_ft_fman_fixup_port() to fix port for kernel.
2, Implemented fdt_fixup_board_enet() to fix node status of different
slots and interfaces.
3, Adding detection of slot present for XGMII interface.
4, There is no PHY for XFI, so removed related phy address settings.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When CONFIG_SYS_FSL_QORIQ_CHASSIS2 is not defined, QMAN frequency will not
be initialized, and QMAN will have a wrong frequency display.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T4160 SoC is low power version of T4240. The T4160 combines eight dual
threaded Power Architecture e6500 cores and two memory complexes (CoreNet
platform cache and DDR3 memory controller) with the same high-performance
datapath acceleration, networking, and peripheral bus interfaces.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Protocols are constants. Fix arrays with const prefix.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The PIR parsing algorithm we used is not only for E6500. It applies to all
SoCs with chassis 2.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Use decimal and hexadecimal for protocol numbers. It helps to match with
SoC user manual.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T4240 internal UTMI phy is different comparing to previous UTMI PHY
in P3041.
This patch adds USB 2.0 UTMI Dual PHY new memory map and enable it for
T4240.
The phy timing is very sensitive and moving the phy enable code to
cpu_init.c will not work.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Missing nodes of crypto, pme, etc in device tree is not a fatal error.
Setting up the qman portal should skip the missing node and continue
to finish the rest.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Should check if interleaving is enabled before using interleaving mode.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Lane H on SerDes4 should be SATA2 instead of SATA1
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The L1 D-cache on e6500 is write-through. This means that it's not
considered a good idea to have the L1 up and running if the L2 is
disabled. We don't actually *use* the L1 until after the L2 is
brought up on e6500, so go ahead and move the L1 enablement after
that code is done.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Fix ccsr_gur for corenet platform. Remove non-exist registers. Add fuse
status register.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Makes it a bit easier to see if we've properly set them. While
we're in there, modify the accesses to HDBCR0 and HDBCR1 to actually
use those definitions.
Signed-off-by: Andy Fleming <afleming@freescale.com>
The bit positions for FMAN1 freq in RCW is different for B4860.
Also addded a case when FMAN1 frewuency is equal to systembus.
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Rather than having similar code in powerpc, use image_setup_linux() which
should be common across all architectures that use the FDT.
Signed-off-by: Simon Glass <sjg@chromium.org>
Extending LIODN offset range from 1-5 to 1-10
While using a qman portal with a higher index the LIODN offset
is incorrectly set, thus extending the range of offsets covers
all 10 qman portals
Signed-off-by: Cristian Sovaiala <cristian.sovaiala@freescale.com>
Acked-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Erratum DDR_A003 applies to P5020, P3041, P4080, P3060, P2041, P5040.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Only some chips have four SerDes banks, so don't define lanes for a bank
that doesn't exist.
Signed-off-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
As per Errata list of BSC9131 and BSC9132, IFC Errata A003399 is no more
valid. So donot compile its workaround.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
On P204x/P304x/P50x0 Rev1.0, USB transmit will result in false internal
multi-bit ECC errors, which has impact on performance, so software should
disable all ECC reporting from USB1 and USB2.
In formal release document, the errata number should be USB14 instead of USB138.
Signed-off-by: xulei <Lei.Xu@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: xulei <B33228@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Some legacy RGMII phys don't have in band signaling for the
speed information. so set the RGMII MAC mode according to
the speed got from PHY.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Reported-by: John Traill <john.traill@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
For T4/B4, the clockgen node compatible string is updated to version 2.
Add clock-frequency setting for this new version.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Per the latest errata updated, B4860/B4420 Rev 1.0 has also
errata A-005871, so adding define A-005871 for B4 SoCs.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
B4420/B4860 PCIE can not work because of the wrong definition of
the PCIE register offset in the file:
arch/powerpc/include/asm/immap_85xx.h
Add the judgement of B4420/B4860 to make the register offset to:
#define CONFIG_SYS_MPC85xx_PCIE1_OFFSET 0x200000
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Set the device tree property associated with the mpic source
frequency. The frequency is used for mpic timer.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The 'fsl,pme-rev1' and 'fsl-pme-rev2' properties have been added to the
pme portal node. This is required for software to determine which version
of PME hardware is present and take appropriate actions.
These properties are a direct reflection of the corresponding ccsr pme
register value.
Also removed unnecessary static global variables.
Signed-off-by: Jeffrey Ladouceur <Jeffrey.Ladouceur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Delete all occurrences of hang() and provide a generic function.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
[trini: Modify check around puts() in hang.c slightly]
Signed-off-by: Tom Rini <trini@ti.com>
Make all mpc512x code point to the new common fsl_iim driver, and remove the
former mpc512x-specific iim driver.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This patch adds SPL booting support (NOR flash) for the
PPC4xx platforms.
This SPL booting (Falcon mode) will be used by the upcoming
lcd4_lwmon5 board port (lwmon5 variant).
Signed-off-by: Stefan Roese <sr@denx.de>
If watchdog is enabled, the arch/powerpc/lib/ticks.S::wait_ticks() function
calls the function specified by the WATCHDOG_RESET macro.
The wait_ticks function depends on the registers r0, r6 and r7 being
preserved however that is not guaranteed, e.g. if the reset function is a
C function this will probably overwrite r0 and cause an endless loop.
The following patch changes to using r14+r15 instead of r6+r7 (to resemble
what would have been generated by a C compiler) and saves all necessary
registers on the stack.
The patch has been tested on a custom MPC5125 based machine using the 512x
powerpc architecture.
Signed-off-by: Mats Karrman <mats.karrman@tritech.se>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Tested-by: Stefan Roese <sr@denx.de>
Fix USB device-tree fixup to properly handle device-tree fixup and
print appropriate message when wrong/junk "dr_mode" or "phy_type"
are mentioned in hwconfig string
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
'bool' is defined in random places. This patch consolidates them into a
single header file include/linux/types.h, using stdbool.h introduced in C99.
All other #define, typedef and enum are removed. They are all consistent with
true = 1, false = 0.
Replace FALSE, False with false. Replace TRUE, True with true.
Skip *.py, *.php, lib/* files.
Signed-off-by: York Sun <yorksun@freescale.com>
Since the lcd code was compiled unconditionally in arch also
add CONFIG_MPC8XX_LCD to the boards using this driver.
cc: Anatolij Gustschin <agust@denx.de>
cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
lcd_color_fg and lcd_color_bg had to be declared in board specific
code, but were not actually used there; in addition, we have getter /
setter functions for these, which were not used either.
Get rid of the global variables, and use the getter function where
needed (so far no setter calls are needed).
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stelian Pop <stelian@popies.net>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Jeroen Hofstee <jeroen@myspectrum.nl>
[agust: also fixed cm_t35 board while rebasing]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Albert's rework of the linker scripts conflicted with Simon's making
everyone use __bss_end. We also had a minor conflict over
README.scrapyard being added to in mainline and enhanced in
u-boot-arm/master with proper formatting.
Conflicts:
arch/arm/cpu/ixp/u-boot.lds
arch/arm/cpu/u-boot.lds
arch/arm/lib/Makefile
board/actux1/u-boot.lds
board/actux2/u-boot.lds
board/actux3/u-boot.lds
board/dvlhost/u-boot.lds
board/freescale/mx31ads/u-boot.lds
doc/README.scrapyard
include/configs/tegra-common.h
Build tested for all of ARM and run-time tested on am335x_evm.
Signed-off-by: Tom Rini <trini@ti.com>
These functions are only available for powerpc and are not declared in a
header file. We want to use the rest function in two places (board_f and
board_r), so declare the functions in watchdog.h.
Signed-off-by: Simon Glass <sjg@chromium.org>
We create a separate header file for link symbols defined by the link
scripts. It is helpful to have these all in one place and try to
make them common across architectures. Since Linux already has a similar
file, we bring this in even though many of the symbols there are not
relevant to us.
Each architecture has its own asm/sections.h where symbols specifc to
that architecture can be added. For now everything except AVR32 just
includes the generic header.
One change is needed in arch/avr32/lib/board.c to make this conversion
work.
Reviewed-by: Tom Rini <trini@ti.com> (version 5)
Signed-off-by: Simon Glass <sjg@chromium.org>
Note this is a tree-wide change affecting multiple architectures.
At present we use __bss_start, but mostly __bss_end__. This seems
inconsistent and in a number of places __bss_end is used instead.
Change to use __bss_end for the BSS end symbol throughout U-Boot. This
makes it possible to use the asm-generic/sections.h file on all
archs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Refactor linker-generated array code so that symbols
which were previously linker-generated are now compiler-
generated. This causes relocation records of type
R_ARM_ABS32 to become R_ARM_RELATIVE, which makes
code which uses LGA able to run before relocation as
well as after.
Note: this affects more than ARM targets, as linker-
lists span possibly all target architectures, notably
PowerPC.
Conflicts:
arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds
arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds
arch/arm/cpu/armv7/omap-common/u-boot-spl.lds
board/ait/cam_enc_4xx/u-boot-spl.lds
board/davinci/da8xxevm/u-boot-spl-da850evm.lds
board/davinci/da8xxevm/u-boot-spl-hawk.lds
board/vpac270/u-boot-spl.lds
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
These boards seem to be unmaintained for quite some time. So lets
remove support for them completely. This also cleans up some
common drivers/files.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Guillaume Alexandre <guillaume.alexandre@gespac.ch>
Acked-by: Wolfgang Denk <wd@denx.de>
Do maintain a 200 usecs period of stable power and clock before
asserting the CKE signal and sending commands, have at least 200
DRAM clock cycles pass after initialization before data access.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add new mpc5121e based ac14xx board and a new pinmux config
function for setting individual pinmux bit groups. This
function is used in ac14xx board code.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Boards may define own IPS divider in the config file if
the default IPS divider doesn't fit their needs.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Only define enabled clocks in the config file and enable
the clocks in common code.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Wolfgang Denk <wd@denx.de>
Currently each mpc512x board has its own LAW and CS config code,
we should avoid this code duplication. Allow all boards to use
common code by only defining LAW and CS config macros like
CONFIG_SYS_CSx_START, CONFIG_SYS_CSx_SIZE and CONFIG_SYS_CSx_CFG.
Also allow common configuration of additional CS parameters by
CONFIG_SYS_CS_ALETIMING, CONFIG_SYS_CS_BURST, CONFIG_SYS_CS_DEADCYCLE
and CONFIG_SYS_CS_HOLDCYCLE options.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
On MPC5200, the initial RAM (and gd) is located in the internal
SRAM. So we can actually call the preloader console init code
before calling initdram(). This makes serial output (printf)
available very early, even before SDRAM init, which has been
an U-Boot priciple from day 1.
Signed-off-by: Stefan Roese <sr@denx.de>
The libfdt.h file is the definition file for libfdt. It is unnecessary
to include other fdt header files (the necessary ones are pulled in
by libfdt.h).
Signed-off-by: Gerald Van Baren <gvb@unssw.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefan Roese <sr@denx.de>
trivial:
fdt_support.c:89:64: warning: Using plain integer as NULL pointer
fdt_support.c:325:65: warning: Using plain integer as NULL pointer
fdt_support.c:352:65: warning: Using plain integer as NULL pointer
For the following bad constant expression, We hardcode the max. number of
memory banks to four for the foreseeable future, and add an error with
instructions on what to do once it's exceeded:
fdt_support.c:397:22: error: bad constant expression
For the rest below, sparse found a couple of wrong endian conversions
in of_bus_default_translate() and fdt_get_base_address(), but
otherwise the rest is mostly annotation fixes:
fdt_support.c:64:24: warning: cast to restricted __be32
fdt_support.c:192:21: warning: incorrect type in assignment (different base types)
fdt_support.c:192:21: expected unsigned int [unsigned] [usertype] tmp
fdt_support.c:192:21: got restricted __be32 [usertype] <noident>
fdt_support.c:201:21: warning: incorrect type in assignment (different base types)
fdt_support.c:201:21: expected unsigned int [unsigned] [addressable] [usertype] tmp
fdt_support.c:201:21: got restricted __be32 [usertype] <noident>
fdt_support.c:304:13: warning: incorrect type in assignment (different base types)
fdt_support.c:304:13: expected unsigned int [unsigned] [usertype] val
fdt_support.c:304:13: got restricted __be32 [usertype] <noident>
fdt_support.c:333:13: warning: incorrect type in assignment (different base types)
fdt_support.c:333:13: expected unsigned int [unsigned] [usertype] val
fdt_support.c:333:13: got restricted __be32 [usertype] <noident>
fdt_support.c:359:13: warning: incorrect type in assignment (different base types)
fdt_support.c:359:13: expected unsigned int [unsigned] [usertype] val
fdt_support.c:359:13: got restricted __be32 [usertype] <noident>
fdt_support.c:373:21: warning: cast to restricted __be32
fdt_support.c:963:48: warning: incorrect type in argument 1 (different base types)
fdt_support.c:963:48: expected restricted __be32 const [usertype] *p
fdt_support.c:963:48: got unsigned int [usertype] *<noident>
fdt_support.c:971:48: warning: incorrect type in argument 1 (different base types)
fdt_support.c:971:48: expected restricted __be32 const [usertype] *p
fdt_support.c:971:48: got unsigned int [usertype] *<noident>
fdt_support.c:984:29: warning: incorrect type in argument 1 (different base types)
fdt_support.c:984:29: expected restricted __be32 const [usertype] *cell
fdt_support.c:984:29: got unsigned int [usertype] *addr
fdt_support.c:996:32: warning: incorrect type in argument 1 (different base types)
fdt_support.c:996:32: expected restricted __be32 const [usertype] *cell
fdt_support.c:996:32: got unsigned int [usertype] *addr
fdt_support.c:1041:41: warning: incorrect type in argument 1 (different base types)
fdt_support.c:1041:41: expected restricted __be32 const [usertype] *cell
fdt_support.c:1041:41: got unsigned int [usertype] *addr
fdt_support.c:1053:41: warning: incorrect type in argument 2 (different base types)
fdt_support.c:1053:41: expected restricted __be32 const [usertype] *range
fdt_support.c:1053:41: got unsigned int const [usertype] *[assigned] ranges
fdt_support.c:1064:53: warning: incorrect type in argument 2 (different base types)
fdt_support.c:1064:53: expected restricted __be32 const [usertype] *addr
fdt_support.c:1064:53: got unsigned int [usertype] *addr
fdt_support.c:1110:50: warning: incorrect type in argument 2 (different base types)
fdt_support.c:1110:50: expected restricted __be32 const [usertype] *addr
fdt_support.c:1110:50: got unsigned int *<noident>
fdt_support.c:1121:49: warning: incorrect type in argument 1 (different base types)
fdt_support.c:1121:49: expected restricted __be32 const [usertype] *cell
fdt_support.c:1121:49: got unsigned int *<noident>
fdt_support.c:1147:60: warning: incorrect type in argument 2 (different base types)
fdt_support.c:1147:60: expected restricted __be32 const [usertype] *addr
fdt_support.c:1147:60: got unsigned int *<noident>
fdt_support.c:1081:5: warning: symbol '__of_translate_address' was not declared. Should it be static?
fdt_support.c:1154:5: error: symbol 'fdt_translate_address' redeclared with different type (originally declared at include/fdt_support.h:95) - incompatible argument 3 (different base types)
fdt_support.c: In function 'fdt_node_offset_by_compat_reg':
fdt_support.c:1173:17: warning: initialization discards 'const' qualifier from pointer target type [enabled by default]
See also linux kernel commit 0131d897 "of/address: use proper
endianess in get_flags".
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Jerry Van Baren <gvb.uboot@gmail.com>
and, if including libfdt.h which includes libfdt_env.h in
the correct order, don't include fdt.h before libfdt.h.
this is needed to get the fdt type definitions set from
the project environment before fdt.h uses them.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Jerry Van Baren <gvb.uboot@gmail.com>
Move these fields into arch_global_data and tidy up. The bExtUart field
does not appear to be used, so punt it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move these fields into arch_global_data and tidy up. This is needed for
both ppc and m68k since they share the i2c driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move these fields into arch_global_data and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Update for bsc9132qds.c, b4860qds.c]
Signed-off-by: Tom Rini <trini@ti.com>
Move vco_out, cpm_clk, scc_clk, brg_clk into arch_global_data and tidy
up. Leave pci_clk on its own since this should really depend only on
CONFIG_PCI and not any particular chip type.
Signed-off-by: Simon Glass <sjg@chromium.org>
PPC has several of these fields, selected by chip type, although only one
is ever compiled in.
Instead, use a single field. It would be nice if this could be selected
by CONFIG_PCI, but some chips (e.g. mpc5xxx) use pci_clk even when
CONFIG_PCI is not enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
We plan to move architecture-specific data into a separate structure so
that we can make the rest of it common.
As a first step, create struct arch_global_data to hold these fields.
Initially it is empty.
This patch applies to all archs at once. I can split it if this is really
a pain.
Signed-off-by: Simon Glass <sjg@chromium.org>
When CoreNet Fabric (CCF) internal resources are consumed by the cores,
inbound SRIO messaging traffic through RMan can put the device into a
deadlock condition.
This errata workaround forces internal resources to be reserved for
upstream transactions. This ensures resources exist on the device for
upstream transactions and removes the deadlock condition.
The Workaround is for the T4240 silicon rev 1.0.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
If property 'fsl,sec-era' is already present, it is updated.
This property is required so that applications can ascertain which
descriptor commands are supported on a particular CAAM version.
Signed-off-by: Vakul Garg <vakul@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Configuring custom memory init value using CONFIG_MEM_INIT_VALUE in
the board config file doesn't work and memory is always initialized
to the value 0xdeadbeef. Only use this default value if a board doesn't
define CONFIG_MEM_INIT_VALUE.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
e6500 implements MMUv2 and supports power-of-2 page sizes rather than
power-of-4. Add support for such pages.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The BSC9132 is a highly integrated device that targets the evolving
Microcell, Picocell, and Enterprise-Femto base station market subsegments.
The BSC9132 device combines Power Architecture e500 and DSP StarCore SC3850
core technologies with MAPLE-B2P baseband acceleration processing elements
to address the need for a high performance, low cost, integrated solution
that handles all required processing layers without the need for an
external device except for an RF transceiver or, in a Micro base station
configuration, a host device that handles the L3/L4 and handover between
sectors.
The BSC9132 SoC includes the following function and features:
- Power Architecture subsystem including two e500 processors with
512-Kbyte shared L2 cache
- Two StarCore SC3850 DSP subsystems, each with a 512-Kbyte private L2
cache
- 32 Kbyte of shared M3 memory
- The Multi Accelerator Platform Engine for Pico BaseStation Baseband
Processing (MAPLE-B2P)
- Two DDR3/3L memory interfaces with 32-bit data width (40 bits including
ECC), up to 1333 MHz data rate
- Dedicated security engine featuring trusted boot
- Two DMA controllers
- OCNDMA with four bidirectional channels
- SysDMA with sixteen bidirectional channels
- Interfaces
- Four-lane SerDes PHY
- PCI Express controller complies with the PEX Specification-Rev 2.0
- Two Common Public Radio Interface (CPRI) controller lanes
- High-speed USB 2.0 host and device controller with ULPI interface
- Enhanced secure digital (SD/MMC) host controller (eSDHC)
- Antenna interface controller (AIC), supporting four industry
standard JESD207/four custom ADI RF interfaces
- ADI lanes support both full duplex FDD support & half duplex TDD
- Universal Subscriber Identity Module (USIM) interface that
facilitates communication to SIM cards or Eurochip pre-paid phone
cards
- Two DUART, two eSPI, and two I2C controllers
- Integrated Flash memory controller (IFC)
- GPIO
- Sixteen 32-bit timers
Signed-off-by: Naveen Burmi <NaveenBurmi@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch adds the ability for the FSL DDR interactive debugger to
automatically run the sequence of commands stored in the ddr_interactive
environment variable. Commands are separated using ';'.
ddr_interactive=compute; edit c0 d0 dimmparms caslat_X 0x3FC0; go
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add copy command which allows copying of DIMM/controller settings.
This saves tedious retyping of parameters for each identical DIMM
or controller.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This fix allows the name of the stage to be specifed after the
controler and DIMM is specified. Prior to this fix, if the
data stage name is not the first entry on the command line,
the operation is applied to all controller and DIMMs.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Move the FSL DDR prompt command parsing to a separate function
so that it can be reused.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Using environmental variable "ddr_interactive" to activate interactive DDR
debugging seomtiems is not enough. For example, after updating SPD with a
valid but wrong image, u-boot won't come up due to wrong DDR configuration.
By enabling key press method, we can enter debug mode to have a chance to
boot without using other tools to recover the board.
CONFIG_FSL_DDR_INTERACTIVE needs to be defined in header file. To enter the
debug mode by key press, press key 'd' shortly after reset, like one would
do to abort auto booting. It is fixed to lower case 'd' at this moment.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Different personalities/derivatives of SoC may have reduced cluster. But it is
not necessary for last valid DCFG_CCSR_TP_CLUSTER register to have
DCFG_CCSR_TP_CLUSTER[EOC] bit set to represent "End of Clusters".
EOC bit can still be set in last DCFG_CCSR_TP_CLUSTER register of orignal SoC
which may not be valid for the personality.
So add initiator type check to find valid cluster.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The boot page in memory is already reserved so OS won't overwrite.
As long as the boot page translation is active, the default boot page
also needs to be reserved in case the memory is 4GB or more.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This adds arch support for PPC mpc83xx to boot "minimal" (4K) SPLs
using the new infrastructure.
Existing nand_spl targets are updated to deal with the name change
from nand_init.c to spl_minimal.c (as in theory this isn't limited
to NAND anymore).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Move the getenv_yesno() to env_common.c and change most checks for
'y' or 'n' to use this helper.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
strncasecmp() is present as strnicmp() but disabled. Make it available
and define strcasecmp() also. There is a only a small performance penalty
to having strcasecmp() call strncasecmp(), so do this instead of a
standalone function, to save code space.
Update the prototype in arch-specific headers as needed to avoid warnings.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch enables the SPL framework to be used on powerpc platforms
and not only ARM.
timer_init() does not exist on PPC systems. The timer (decrementer) is
initialized and enabled in interrupt_init() here. And currently
interrupt_init() is called after relocation to SDRAM. Since the only
powerpc SPL implementation (a3m071) doesn't need a timer, let's remove
this timer_init() call for PPC systems.
Signed-off-by: Stefan Roese <sr@denx.de>
By extracting these defines into a header, they can be re-used by other
C sources as well. This will be done by the SPL framework OS boot
support.
Signed-off-by: Stefan Roese <sr@denx.de>
Fix a bug introduced by this patch
powerpc/mpc85xx: Temporary fix for spin table backward compatibility
Should have checked both CONFIG_PPC_SPINTABLE_COMPATIBLE and CONFIG_MP in
cpu_init.c.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The documented work-around for P4080 erratum SERDES-9 has been updated.
It is now compatible with the work-around for erratum A-4580.
This requires adding a few bitfield macros for the BnTTLCRy0 register.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Due to SerDes configuration error, if we set the PCI-e controller link width
as x8 in RCW and add a narrower width(such as x4, x2 or x1) PCI-e device to
PCI-e slot, it fails to train down to the PCI-e device's link width. According
to p4080ds errata PCIe-A003, we reset the PCI-e controller link width to x4 in
u-boot. Then it can train down to x2 or x1 width to make the PCI-e link between
RC and EP.
Signed-off-by: Yuanquan Chen <B41889@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
board configuration file is included before asm/config_mpc85xx.h.
however, CONFIG_FSL_SATA_V2 is defined in asm/config_mpc85xx.h.
it will never take effective in the board configuration file for
this kind of code :
#ifdef CONFIG_FSL_SATA_V2
...
#endif
To solve this problem, move CONFIG_FSL_SATA_V2 to board
configuration header file.
This patch reverts Timur's
commit:3e0529f742e893653848494ffb9f7cd0d91304bf
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The work-around for erratum A-004580 ("Internal tracking loop can falsely
lock causing unrecoverable bit errors") is implemented via the PBI
(pre-boot initialization code, typically attached to the RCW binary).
This is because the work-around is easier to implement in PBI than in
U-Boot itself.
It is still useful, however, for the 'errata' command to tell us whether
the work-around has been applied. For A-004580, we can do this by verifying
that the values in the specific registers that the work-around says to
update.
This change requires access to the SerDes lane sub-structure in
serdes_corenet_t, so we make it a named struct.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
by moving compat_strlist into the .bss section.
0xfe004d80 fdt_fixup_crypto_node [u-boot]: 264
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Once u-boot sets the spin table to cache-enabled memory, old kernel which
uses cache-inhibit mapping without coherence will not work properly. We
use this temporary fix until kernel has updated its spin table code.
For now this fix is activated by default. To disable this fix for new
kernel, set environmental variable "spin_table_compat=no". After kernel
has updated spin table code, this default shall be changed.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The work-around for erratum A-004849 ("CoreNet fabric (CCF) can exhibit a
deadlock under certain traffic patterns causing the system to hang") is
implemented via the PBI (pre-boot initialization code, typically attached
to the RCW binary). This is because the work-around is easier to implement
in PBI than in U-Boot itself.
It is still useful, however, for the 'errata' command to tell us whether
the work-around has been applied. For A-004849, we can do this by verifying
that the values in the specific registers that the work-around says to
update.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The P5040 has an e5500 core, so CONFIG_SYS_PPC64 should be defined in
config_mpc85xx.h. This macro was absent in the initial P5040 patch because
it crossed paths with the patch that introduced the macro.
Also delete CONFIG_SYS_FSL_ELBC_MULTIBIT_ECC, since it's not used in the
upstream U-Boot. It's a holdover from the SDK.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
There were a number of shared files that were using
CONFIG_SYS_MPC85xx_DDR_ADDR, or CONFIG_SYS_MPC86xx_DDR_ADDR, and
several variants (DDR2, DDR3). A recent patchset added
85xx-specific ones to code which was used by 86xx systems.
After reviewing places where these constants were used, and
noting that the type definitions of the pointers assigned to
point to those addresses were the same, the cleanest approach
to fixing this problem was to unify the namespace for the
85xx, 83xx, and 86xx DDR address definitions.
This patch does:
s/CONFIG_SYS_MPC8.xx_DDR/CONFIG_SYS_MPC8xxx_DDR/g
All 85xx, 86xx, and 83xx have been built with this change.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Tested-by: Andy Fleming <afleming@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Update CONFIG_RAMBOOT and CONFIG_NAND_SPL references to accept CONFIG_SPL
and CONFIG_SPL_BUILD, respectively. CONFIG_NAND_SPL can be removed once
the last mpc85xx nand_spl target is gone.
CONFIG_RAMBOOT will need to remain for other use cases, but it doesn't
seem right to overload it for meaning SPL as well as nand_spl does. Even
if it's somewhat appropriate for the main u-boot, the SPL itself isn't
(necessarily) ramboot, and we don't have separate configs for SPL and
main u-boot. It was also inconsistent, as other platforms such as
mpc83xx didn't use CONFIG_RAMBOOT in this way.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
cpu_init_nand.c is renamed to spl_minimal.c as it is not really NAND-specific.
Signed-off-by: Scott Wood <scottwood@freescale.com>
---
v2: factor out START, and change cpu_init_nand.c to spl_minimal.c
Cc: Andy Fleming <afleming@freescale.com>
A subsequent patch will conditionalize some of the files that are
currently unconditional.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
It applies to non-Freescale 85xx boards as well as Freescale boards,
so it doesn't belong in board/freescale. Plus, it needs to come out
of nand_spl if it's to be used by the new SPL.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
It's arch code and not a driver, so move it where it belongs. When it
originally went into drivers/misc there was no 8xxx CPU directory.
This will make new-SPL support a little easier since we can keep the CPU
stuff together and not need to pull stuff in from drivers/misc.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
In the RAMBOOT/SPL case we were creating a TLB entry starting at
CONFIG_SYS_MONITOR_BASE, and just hoping that the base was properly
aligned for the TLB entry size. This turned out to not be the case
with NAND SPL because the main U-Boot starts at an offset into the image
in order to skip the SPL itself.
Fix the TLB entry to always start at a proper alignment. We still assume that
CONFIG_SYS_MONITOR_BASE doesn't start immediately before a large-page boundary
thus requiring multiple TLB entries.
Signed-off-by: Scott Wood <scottwood@frescale.com>
Cc: Andy Fleming <afleming@freescale.com>
This was introduced by commit 2446151974, but it
fails in a minimal SPL build where the only thing in arch/powerpc/lib is
cache.c, which apparently doesn't generate any fixup records.
The problem is reported to occur with GCC 3.x, so insist on GCC 4.0 or newer.
Patterned after checkthumb as suggested by Tom Rini.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Tom Rini <trini@ti.com>
--
v2: test gcc version instead of testing nothing
Now outputs like this:
L2: 512 KB already enabled, moving to 0xf8f80000
rather than this:
L2: 512 KB already enabledmoving to 0xf8f80000
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Previously, in many if not all configs we were creating overlapping TLB entries
which is illegal. This caused a crash during boot when moving p2020rdb NAND SPL
into L2 SRAM.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
--
Prabhakar, please test that debug still works.
Linux usb/ch9.h seems to have all the same information (and more)
as usbdescriptors.h so use the former instead of the later one.
As a consequense of this change USB_SPEED_* values don't correspond
directly to EHCI speed encoding anymore, I've added necessary
recoding in EHCI driver. Also there is no point to put speed into
pipe anymore so it's removed and a bunch of host drivers fixed to
look at usb_device->speed instead.
Old usbdescriptors.h included is not removed as it seems to be
used by old USB device code.
This makes usb.h and usbdevice.h incompatible. Fortunately the
only place that tries to include both are the old MUSB code and
it needs usb.h only for USB_DMA_MINALIGN used in aligned attribute
on musb_regs structure but this attribute seems to be unneeded
(old MUSB code doesn't support any DMA at all).
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
fdt.c:91:78: warning: Using plain integer as NULL pointer
fdt.c:103:78: warning: Using plain integer as NULL pointer
speed.c:55:11: warning: symbol 'corecnf_tab' was not declared. Should it be static?
speed.c:519:5: warning: symbol 'do_clocks' was not declared. Should it be static?
mpc8313erdb.c:73:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:74:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:75:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:76:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:79:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:80:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:81:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:82:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:85:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:86:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:87:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:88:17: warning: obsolete struct initializer, use C99 syntax
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
fsl_corenet_serdes.c:485:6: warning: symbol '__soc_serdes_init' was not declared. Should it be static?
cpu_init.c:185:6: warning: symbol 'invalidate_cpc' was not declared. Should it be static?
bcsr.c:28:27: warning: non-ANSI function declaration of function 'enable_8568mds_duart'
bcsr.c:39:33: warning: non-ANSI function declaration of function 'enable_8568mds_flash_write'
bcsr.c:46:34: warning: non-ANSI function declaration of function 'disable_8568mds_flash_write'
bcsr.c:53:29: warning: non-ANSI function declaration of function 'enable_8568mds_qe_mdio'
bcsr.c:28:33: warning: non-ANSI function declaration of function 'enable_8569mds_flash_write'
bcsr.c:33:34: warning: non-ANSI function declaration of function 'disable_8569mds_flash_write'
bcsr.c:38:28: warning: non-ANSI function declaration of function 'enable_8569mds_qe_uec'
bcsr.c:63:47: warning: non-ANSI function declaration of function 'disable_8569mds_brd_eeprom_write_protect'
ngpixis.c:245:1: error: directive in argument list
ngpixis.c:247:1: error: directive in argument list
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
ctrl_regs.c:31:5: warning: symbol 'fsl_ddr_get_version' was not declared. Should it be static?
cpu.c:135:14: warning: non-ANSI function declaration of function 'cpu_mask'
cpu.c:154:18: warning: non-ANSI function declaration of function 'cpu_numcores'
cpu.c:37:17: warning: symbol 'cpu_type_list' was not declared. Should it be static?
cpu.c:117:17: warning: symbol 'cpu_type_unknown' was not declared. Should it be static?
fsl_lbc.c:14:6: warning: symbol '__lbc_sdram_init' was not declared. Should it be static?
and:
lc_common_dimm_params.c:15:1: warning: symbol 'compute_cas_latency_ddr3' was not declared. Should it be static?
making it static produces the following compiler warning:
lc_common_dimm_params.c:15:1: warning: 'compute_cas_latency_ddr3' defined but not used [-Wunused-function]
so we protect it with the preprocessor.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
traps.c:*:1: warning: symbol 'print_backtrace' was not declared. Should it be static?
traps.c:93:1: warning: symbol '_exception' was not declared. Should it be static?
board.c:166:6: warning: symbol '__board_add_ram_info' was not declared. Should it be static?
board.c:174:5: warning: symbol '__board_flash_wp_on' was not declared. Should it be static?
board.c:187:6: warning: symbol '__cpu_secondary_init_r' was not declared. Should it be static?
board.c:265:12: warning: symbol 'init_sequence' was not declared. Should it be static?
board.c:348:5: warning: symbol '__fixup_cpu' was not declared. Should it be static?
board.c:405:53: warning: Using plain integer as NULL pointer
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
extable.c:66:9: warning: symbol 'ex_tab_message' was not declared. Should it be static?
making it static can produce a new build warning on some boards:
extable.c:66:12: warning: 'ex_tab_message' defined but not used [-Wunused-variable]
but ex_tab_message doesn't do much even when used, so just remove it.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
a fixup __iomem definition in arch code appears to be placed there as a cover
up from a code import from linux when u-boot didn't yet have a compiler.h,
introduced by commit 812711ce6b "Implement
__raw_{read,write}[bwl] on all architectures".
git show 812711ce6b3a386125dcf0d6a59588e461abbb87:include/linux/compiler.h
fatal: Path 'include/linux/compiler.h' exists on disk, but not in '812711ce6b3a386125dcf0d6a59588e461abbb87'.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
u-boot's byteorder headers did not contain endianness attributions
for use with sparse, causing a lot of false positives. Import the
kernel's latest definitions, and enable them by including compiler.h
and types.h. They come with 'const' added for some swab functions, so
fix those up, too:
include/linux/byteorder/big_endian.h:46:2: warning: passing argument 1 of '__swab64p' discards 'const' qualifier from pointer target type [enabled by default]
Also, note: u-boot's historic __BYTE_ORDER definition has been
preserved (for the time being at least).
We also remove ad-hoc barrier() definitions, since we're including
compiler.h in files that hadn't in the past:
macb.c:54:0: warning: "barrier" redefined [enabled by default]
In addition, including compiler.h in byteorder changes the 'noinline'
definition to expand to __attribute__((noinline)). This fixes
arch/powerpc/lib/bootm.c:
bootm.c:329:16: error: attribute '__attribute__': unknown attribute
bootm.c:329:16: error: expected ')' before '__attribute__'
bootm.c:329:25: error: expected identifier or '(' before ')' token
powerpc sparse builds yield:
include/common.h:356:22: error: marked inline, but without a definition
the unknown-reason inlining without a definition is considered obsolete
given it was part of the 2002 initial commit, and no arm version was
'fixed.'
also fixed:
ydirectenv.h:60:0: warning: "inline" redefined [enabled by default]
and:
Configuring for devconcenter - Board: intip, Options: DEVCONCENTER
make[1]: *** [4xx_ibm_ddr2_autocalib.o] Error 1
make: *** [arch/powerpc/cpu/ppc4xx/libppc4xx.o] Error 2
powerpc-fsl-linux-size: './u-boot': No such file
4xx_ibm_ddr2_autocalib.c: In function 'DQS_autocalibration':
include/asm/ppc4xx-sdram.h:1407:13: sorry, unimplemented: inlining failed in call to 'ppc4xx_ibm_ddr2_register_dump': function body not available
4xx_ibm_ddr2_autocalib.c:1243:32: sorry, unimplemented: called from here
and:
In file included from crc32.c:50:0:
crc32table.h:4:1: warning: implicit declaration of function '___constant_swab32' [-Wimplicit-function-declaration]
crc32table.h:4:1: error: initializer element is not constant
crc32table.h:4:1: error: (near initialization for 'crc32table_le[0]')
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
[trini: Remove '#endif' in include/common.h around setenv portion]
Signed-off-by: Tom Rini <trini@ti.com>
These boards have long reached EOL, and there has been no indication
of any active users of such hardware for years. Get rid of the dead
weight.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@denx.de>
This processor, though very similar to other members of the
PowerQUICC II Pro family (namely 8308, 8360 and 832x), provides
yet another feature set than any supported sibling.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Introduce a new configuration token CONFIG_MPC830x to be shared among
mpc8308 and mpc8309. Define it for existing 8308 boards, and refactor
existing common code so to make future introduction of 8309 simpler.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
simplify #if defined(CONFIG_MPC8360) || defined(CONFIG_MPC832x)
for qe variables
with #if defined(CONFIG_QE)
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The timeout_save variable was only used by the DDR111_134
erratum code. It was being set, but never used. Newer compilers
will actually complain about this.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Currently, the SRIO and PCIE boot master module will be compiled into the
u-boot image if the macro "CONFIG_FSL_CORENET" has been defined. And this
macro has been included by all the corenet architecture platform boards.
But in fact, it's uncertain whether all corenet platform boards support
this feature.
So it may be better to get rid of the macro "CONFIG_FSL_CORENET", and add
a special macro for every board which can support the feature. This
special macro will be defined in the header file
"arch/powerpc/include/asm/config_mpc85xx.h". It will decide if the SRIO
and PCIE boot master module should be compiled into the board u-boot image.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Starting from QMan3.0, the QMan clock cycle needs be exposed so that the kernel
driver can use it to calculate the shaper prescaler and rate.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Because QMan3.0 and BMan2.1 used ip_cfg in ip_rev_2 register to differ the
total portal number, buffer pool number etc, we can use this info to limit
those resources in kernel driver.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
New corenet platforms with chassis2 have separated DDR clock inputs. Use
CONFIG_DDR_CLK_FREQ for DDR clock. This patch also cleans up the logic of
detecting and displaying synchronous vs asynchronous mode.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Move spin table to cached memory to comply with ePAPR v1.1.
Load R3 with 64-bit value if CONFIG_SYS_PPC64 is defined.
'M' bit is set for DDR TLB to maintain cache coherence.
See details in doc/README.mpc85xx-spin-table.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
R6 was in ePAPR draft version but was dropped in official spec.
Removing it to comply.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Since empty DIMM slot is allowed on other than the first slot, remove the
error message if SPD is not found in this case.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Based on populated DIMMs, automatically select from cs0_cs1_cs2_cs3 or
cs0_cs1 interleaving, or non-interleaving if not available.
Fix the message of interleaving disabled if controller interleaving
is enabled but DIMMs don't support it.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
After DDR controller is enabled, it performs a calibration for the
transmit data vs DQS paths. During this calibration, the DDR controller
may make an inaccurate calculation, resulting in a non-optimal tap point.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Boot space translation utilizes the pre-translation address to select
the DDR controller target. However, the post-translation address will be
presented to the selected DDR controller. It is possible that the pre-
translation address selects one DDR controller but the post-translation
address exists in a different DDR controller when using certain DDR
controller interleaving modes. The device may fail to boot under these
circumstances. Note that a DDR MSE error will not be detected since DDR
controller bounds registers are programmed to be the same when configured
for DDR controller interleaving.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When ECC is enabled, DDR controller needs to initialize the data and ecc.
The wait time can be calcuated with total memory size, bus width, bus speed
and interleaving mode. If it went wrong, it is bettert to timeout than
waiting for D_INIT to clear, where it probably hangs.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Fix handling quad-rank DIMMs in a system with two DIMM slots and first
slot supports both dual-rank DIMM and quad-rank DIMM.
For systems with quad-rank DIMM and double dual-rank DIMMs, cs_config
registers need to be enabled to maintain proper ODT operation. The
inactive CS should have bnds registers cleared.
Fix the turnaround timing for systems with all chip-selects enabled. This
wasn't an issue before because DDR was running lower than 1600MT/s with
this interleaving mode.
Fix DDR address calculation. It wasn't an issue until we have multiple
controllers with each more than 4GB and interleaving is disabled.
It also fixes the message of DDR: 2 GiB (DDR3, 64-bit, CL=0.5, ECC off)
when debugging DDR and first DDR controller is disabled. With the fix,
the first enabled controller information will be displayed.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
DDRC ver 4.7 adds DDR_SLOW bit in sdram_cfg_2 register. This bit needs to be
set for speed lower than 1250MT/s.
CDR1 and CDR2 are control driver registers. ODT termination valueis for
IOs are defined. Starting from DDRC 4.7, the decoding of ODT for IOs is
000 -> Termsel off
001 -> 120 Ohm
010 -> 180 Ohm
011 -> 75 Ohm
100 -> 110 Ohm
101 -> 60 Ohm
110 -> 70 Ohm
111 -> 47 Ohm
Add two write leveling registers. Each QDS now has its own write leveling
start value. In case of zero value, the value of QDS0 will be used. These
values are board-specific and are set in board files.
Extend DDR register timing_cfg_1 to have 4 bits for each field.
DDR control driver registers and write leveling registers are added to
interactive debugging for easy access.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The multirate ethernet media access controller (mEMAC) interfaces to
10Gbps and below Ethernet/IEEE 802.3 networks via either RGMII/RMII
interfaces or XAUI/XFI/SGMII/QSGMII using the high-speed SerDes interface.
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add support for Freescale B4860 and variant SoCs. Features of B4860 are
(incomplete list):
Six fully-programmable StarCore SC3900 FVP subsystems, divided into three
clusters-each core runs up to 1.2 GHz, with an architecture highly
optimized for wireless base station applications
Four dual-thread e6500 Power Architecture processors organized in one
cluster-each core runs up to 1.8 GHz
Two DDR3/3L controllers for high-speed, industry-standard memory interface
each runs at up to 1866.67 MHz
MAPLE-B3 hardware acceleration-for forward error correction schemes
including Turbo or Viterbi decoding, Turbo encoding and rate matching,
MIMO MMSE equalization scheme, matrix operations, CRC insertion and
check, DFT/iDFT and FFT/iFFT calculations, PUSCH/PDSCH acceleration,
and UMTS chip rate acceleration
CoreNet fabric that fully supports coherency using MESI protocol between
the e6500 cores, SC3900 FVP cores, memories and external interfaces.
CoreNet fabric interconnect runs at 667 MHz and supports coherent and
non-coherent out of order transactions with prioritization and
bandwidth allocation amongst CoreNet endpoints.
Data Path Acceleration Architecture, which includes the following:
Frame Manager (FMan), which supports in-line packet parsing and general
classification to enable policing and QoS-based packet distribution
Queue Manager (QMan) and Buffer Manager (BMan), which allow offloading
of queue management, task management, load distribution, flow ordering,
buffer management, and allocation tasks from the cores
Security engine (SEC 5.3)-crypto-acceleration for protocols such as
IPsec, SSL, and 802.16
RapidIO manager (RMAN) - Support SRIO types 8, 9, 10, and 11 (inbound and
outbound). Supports types 5, 6 (outbound only)
Large internal cache memory with snooping and stashing capabilities for
bandwidth saving and high utilization of processor elements. The
9856-Kbyte internal memory space includes the following:
32 Kbyte L1 ICache per e6500/SC3900 core
32 Kbyte L1 DCache per e6500/SC3900 core
2048 Kbyte unified L2 cache for each SC3900 FVP cluster
2048 Kbyte unified L2 cache for the e6500 cluster
Two 512 Kbyte shared L3 CoreNet platform caches (CPC)
Sixteen 10-GHz SerDes lanes serving:
Two Serial RapidIO interfaces. Each supports up to 4 lanes and a total
of up to 8 lanes
Up to 8-lanes Common Public Radio Interface (CPRI) controller for glue-
less antenna connection
Two 10-Gbit Ethernet controllers (10GEC)
Six 1G/2.5-Gbit Ethernet controllers for network communications
PCI Express controller
Debug (Aurora)
Two OCeaN DMAs
Various system peripherals
182 32-bit timers
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add support for Freescale T4240 SoC. Feature of T4240 are
(incomplete list):
12 dual-threaded e6500 cores built on Power Architecture® technology
Arranged as clusters of four cores sharing a 2 MB L2 cache.
Up to 1.8 GHz at 1.0 V with 64-bit ISA support (Power Architecture
v2.06-compliant)
Three levels of instruction: user, supervisor, and hypervisor
1.5 MB CoreNet Platform Cache (CPC)
Hierarchical interconnect fabric
CoreNet fabric supporting coherent and non-coherent transactions with
prioritization and bandwidth allocation amongst CoreNet end-points
1.6 Tbps coherent read bandwidth
Queue Manager (QMan) fabric supporting packet-level queue management and
quality of service scheduling
Three 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
support
Memory prefetch engine (PMan)
Data Path Acceleration Architecture (DPAA) incorporating acceleration for
the following functions:
Packet parsing, classification, and distribution (Frame Manager 1.1)
Queue management for scheduling, packet sequencing, and congestion
management (Queue Manager 1.1)
Hardware buffer management for buffer allocation and de-allocation
(BMan 1.1)
Cryptography acceleration (SEC 5.0) at up to 40 Gbps
RegEx Pattern Matching Acceleration (PME 2.1) at up to 10 Gbps
Decompression/Compression Acceleration (DCE 1.0) at up to 20 Gbps
DPAA chip-to-chip interconnect via RapidIO Message Manager (RMAN 1.0)
32 SerDes lanes at up to 10.3125 GHz
Ethernet interfaces
Up to four 10 Gbps Ethernet MACs
Up to sixteen 1 Gbps Ethernet MACs
Maximum configuration of 4 x 10 GE + 8 x 1 GE
High-speed peripheral interfaces
Four PCI Express 2.0/3.0 controllers
Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz with
Type 11 messaging and Type 9 data streaming support
Interlaken look-aside interface for serial TCAM connection
Additional peripheral interfaces
Two serial ATA (SATA 2.0) controllers
Two high-speed USB 2.0 controllers with integrated PHY
Enhanced secure digital host controller (SD/MMC/eMMC)
Enhanced serial peripheral interface (eSPI)
Four I2C controllers
Four 2-pin or two 4-pin UARTs
Integrated Flash controller supporting NAND and NOR flash
Two eight-channel DMA engines
Support for hardware virtualization and partitioning enforcement
QorIQ Platform's Trust Architecture 1.1
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The T4 has added devices to previous corenet implementations:
* SEC has 3 more DECO units
* New PMAN device
* New DCE device
This doesn't add full support for the new devices. Just some
preliminary support.
Move PMAN LIODN to upper half of register
Despite having only one LIODN, the PMAN LIODN is stored in the
upper half of the register. Re-use the 2-LIODN code and just
set the LIODN as if the second one is 0. This results in the
actual LIODN being written to the upper half of the register.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Corenet 2nd generation Chassis doesn't have ddr_sync bit in RCW. Only
async mode is supported.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Create new files to handle 2nd generation Chassis as the registers are
organized differently.
- Add SerDes protocol parsing and detection
- Add support of 4 SerDes
- Add CPRI protocol in fsl_serdes.h
The Common Public Radio Interface (CPRI) is publicly available
specification that standardizes the protocol interface between the
radio equipment control (REC) and the radio equipment (RE) in wireless
basestations. This allows interoperability of equipment from different
vendors,and preserves the software investment made by wireless service
providers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Corenet 2nd generation Chassis has different RCW and registers for SerDes.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The QCSP registers are expanded and moved from offset 0 to offset 0x1000
for SoCs with QMan v3.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Expand the reference clock select to three bits
000: 100 MHz
001: 125 MHz
010: 156.25MHz
011: 150 MHz
100: 161.1328125 MHz
All others reserved
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Corenet based SoCs have different core clocks starting from Chassis
generation 2. Cores are organized into clusters. Each cluster has up to
4 cores sharing same clock, which can be chosen from one of three PLLs in
the cluster group with one of the devisors /1, /2 or /4. Two clusters are
put together as a cluster group. These two clusters share the PLLs but may
have different divisor. For example, core 0~3 are in cluster 1. Core 4~7
are in cluster 2. Core 8~11 are in cluster 3 and so on. Cluster 1 and 2
are cluster group A. Cluster 3 and 4 are in cluster group B. Cluster group
A has PLL1, PLL2, PLL3. Cluster group B has PLL4, PLL5. Core 0~3 may have
PLL1/2, core 4~7 may have PLL2/2. Core 8~11 may have PLL4/1.
PME and FMan blocks can take different PLLs, configured by RCW.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Panic if the number of cores is more than CONFIG_MAX_CPUS because it will
surely overflow gd structure.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Chassis generation 2 has different mask and shift. Use macro instead of
magic numbers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Using E6500 L1 cache as initram requires L2 cache enabled.
Add l2-cache cluster enabling.
Setup stash id for L1 cache as (coreID) * 2 + 32 + 0
Setup stash id for L2 cache as (cluster) * 2 + 32 + 1
Stash id for L2 is only set for Chassis 2.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
These assembly macros simplify codes to add and delete temporary TLB entries.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
FSL_HW_PORTAL_PME is used even when CONFIG_SYS_DPAA_PME is not defined.
Remove the #ifdef.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add support for the Freescale P5040 SOC, which is similar to the P5020.
Features of the P5040 are:
Four P5040 single-threaded e5500 cores built
Up to 2.4 GHz with 64-bit ISA support
Three levels of instruction: user, supervisor, hypervisor
CoreNet platform cache (CPC)
2.0 MB configures as dual 1 MB blocks hierarchical interconnect fabric
Two 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
support Up to 1600MT/s
Memory pre-fetch engine
DPAA incorporating acceleration for the following functions
Packet parsing, classification, and distribution (FMAN)
Queue management for scheduling, packet sequencing and
congestion management (QMAN)
Hardware buffer management for buffer allocation and
de-allocation (BMAN)
Cryptography acceleration (SEC 5.2) at up to 40 Gbps SerDes
20 lanes at up to 5 Gbps
Supports SGMII, XAUI, PCIe rev1.1/2.0, SATA Ethernet interfaces
Two 10 Gbps Ethernet MACs
Ten 1 Gbps Ethernet MACs
High-speed peripheral interfaces
Two PCI Express 2.0/3.0 controllers
Additional peripheral interfaces
Two serial ATA (SATA 2.0) controllers
Two high-speed USB 2.0 controllers with integrated PHY
Enhanced secure digital host controller (SD/MMC/eMMC)
Enhanced serial peripheral interface (eSPI)
Two I2C controllers
Four UARTs
Integrated flash controller supporting NAND and NOR flash
DMA
Dual four channel
Support for hardware virtualization and partitioning enforcement
Extra privileged level for hypervisor support
QorIQ Trust Architecture 1.1
Secure boot, secure debug, tamper detection, volatile key storage
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add a new device tree property named "fsl,liodn-offset-list"
holding a list of per pci endpoint permitted liodn offsets.
This property is useful in virtualization scenarios
that implement per pci endpoint partitioning.
The final liodn of a partitioned pci endpoint is
calculated by the hardware, by adding these offsets
to pci controller's base liodn, stored in the
"fsl,liodn" property of its node.
The liodn offsets are interleaved to get better cache
utilization. As an example, given 3 pci controllers,
the following liodns are generated for the pci endpoints:
pci0: 193 256 259 262 265 268 271 274 277
pci1: 194 257 260 263 266 269 272 275 278
pci2: 195 258 261 264 267 270 273 276 279
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The P5040 does not have SRIO support, so there are no SRIO LIODNs.
Therefore, the functions that set the SRIO LIODNs should not be compiled.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The liodn for the new PCIE controller included in P5040DS is no longer set
through a register in the guts register block but with one in the PCIE
register block itself. Update the PCIE CCSR structure to add the new liodn
register and add a new dedicated SET_PCI_LIODN_BASE macro that puts
the liodn in the correct register.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Commit 709389b6 unintentionally used the Unicode version of the
apostrophy. Replace it with the normal ASCII version.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Erratum: A-004034
Affects: SRIO
Description: During port initialization, the SRIO port performs
lane synchronization (detecting valid symbols on a lane) and
lane alignment (coordinating multiple lanes to receive valid data
across lanes). Internal errors in lane synchronization and lane
alignment may cause failure to achieve link initialization at
the configured port width.
An SRIO port configured as a 4x port may see one of these scenarios:
1. One or more lanes fails to achieve lane synchronization.
Depending on which lanes fail, this may result in downtraining
from 4x to 1x on lane 0, 4x to 1x on lane R (redundant lane).
2. The link may fail to achieve lane alignment as a 4x, even
though all 4 lanes achieve lane synchronization, and downtrain
to a 1x. An SRIO port configured as a 1x port may fail to complete
port initialization (PnESCSR[PU] never deasserts) because of
scenario 1.
Impact: SRIO port may downtrain to 1x, or may fail to complete
link initialization. Once a port completes link initialization
successfully, it will operate normally.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Fix usb device-tree fixup:
- wrong modification of dr_mode and phy_type when
"usb1" is not mentioned inside hwconfig string;
now allows hwconfig strings like:
"usb2:dr_mode=host,phy_type=ulpi"
- add warning message for using usb_dr_mode
and usb_phy_type env variables (if either is used)
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The command declaration now uses the new LG-array method to generate
list of commands. Thus the __u_boot_cmd section is now superseded and
redundant and therefore can be removed. Also, remove externed symbols
associated with this section from include/command.h .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Add section for the linker-generated lists into all possible linker
files, so that everyone can easily use these lists. This is mostly
a mechanical adjustment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
P4080 Rev3.0 fixes ESDHC13 errata, so update the code to make the
workaround conditional.
In formal release document, the errata number should be ESDHC13 instead
of ESDHC136.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
We should only write TSR_WIS to the SPRN_TSR register in
reset_85xx_watchdog.
The old code would cause the timer interrupt to be acknowledged when the
watchdog was reset, and we would then get no more timer interrupts.
This bug would affect all mpc85xx boards that have the watchdog enabled.
Signed-off-by: Mark Marshall <Mark.Marshall@omicron.at>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Users of familiar with the Linux gpiolib API expect that value parameter
to gpio_direction_output reflects the initial state of the output pin.
gpio_direction_output was always driving the output low, now it drives
it high or low according to the value provided.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
move most of mpc8xx hooks from cmd_ide.c into ide_preinit() and newly created
ide_init_postreset() (invoked after calling ide_reset after ide_preinit),
some cleanup to make checkpatch happy, enable IDE init hooks in configs of
affected boards.
confusingly, these hooks are used by more than just mpc8xx-based boards, and
therefore are placed in arch/ppc/lib/
note: checkpatch still emits warnings about using volatile
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Replace the in-place ad-hoc implementation of serial_puts() within
the drivers with default_serial_puts() call. This cuts down on the
code duplication quite a bit.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: James F. Dougherty <jfd@broadcom.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Carry an index in the lowlevel usb functions to make specify the
respective usb controller.
Also pass through an controller struct from lowlevel_init to the
creation of the root usb device of this controller.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: James MacAulay <james.macaulay@amirix.com>
Acked-by: Marek Vasut <marex@denx.de>
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peter De Schrijver <p2@mind.be>
Acked-by: Marek Vasut <marex@denx.de>
Since the IOP480 (PPC401/3 variant from PLX) is only used on 2
boards that are not actively maintained, lets remove support
for it completely. This way the ppc4xx code will get a bit cleaner.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Marek Vasut <marex@denx.de>
Remove the parts depending either on disabled CONFIG_SERIAL_MULTI
or ifdefs around CONFIG_SERIAL_MULTI parts since CONFIG_SERIAL_MULTI
is now enabled by default.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Remove the support for not-CONFIG_SERIAL_MULTI part from serial
port drivers and some board files. Since CONFIG_SERIAL_MULTI is
now enabled by default, that part is a dead code. Remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into iop480 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the iop480 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into mpc85xx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the mpc85xx driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into both SCC and SMC mpc8260
serial drivers. These drivers were so far only usable directly, but this
patch also adds support for the multi method. This allows using more than
one serial driver alongside the mpc8260 drivers. Also, add a weak
implementation of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into mpc8220 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the mpc8220 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into mpc5xx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the mpc5xx driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Move the registration of serialN_device ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented mpc512x_serial_initialize() function, which is
implemented inside of the mpc512x serial driver allows encapsulation
of serialN_device within the mpc512x serial driver itself.
Also, remove the exports of serialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the mpx512x serial driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Move the registration of serial_smc and serial_scc ports from
default serial_initialize() into CPU specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The exports of both serial_scc_device and serial_smc_device can
not yet be removed as they are still used in default_serial_console()
calls.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Properly spell out the whole structure member names when an initialized
varible is instantiated from the struct serial_driver. In case the
structure definition for struct serial_driver undergoes reordering,
there will be no impact on variables defined based on this structure.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: C Nauman <cnauman@diagraph.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Michal Simek <monstr@monstr.eu>
Since commit 50a47d0523
(net: punt bd->bi_ip_addr) booting old 2.4.x ppc kernels
is broken due to changed offsets of the fields in struct bd_t.
Offsets of the fields after removed bi_ip_addr are wrong,
causing wrong bus clocks and console baudrate configurations
and various other issues. Re-add the bi_ip_addr field to preserve
backward compatibility with older ppc kernels. Setting bi_ip_addr
in board.c is not really needed, grepping in the 2.4 linux tree
shows that bi_ip_addr is not accessed there. Adding bi_ip_addr
to struct bd_t for other arches isn't needed it seems. bd_t is
not used by other arches in the 2.4 linux tree.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
wait_ticks() calls get_ticks() without building a back chain which
makes gdb unhappy when doing back trace. This can also cause
improper memory accesses.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
This patch moves all bootcount implementations into a common
directory: drivers/bootcount. The generic bootcount driver
is now usable not only by powerpc platforms, but others as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Manfred Rudigier <manfred.rudigier@omicron.at>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
Tested-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Instead of just shooting down the entry that covers CCSR, clear out
every TLB entry that isn't the one that we're executing out of.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Before proper environment is setup, we extract hwconfig and put it into a
buffer with size HWCONFIG_BUFFER_SIZE. We need to enlarge the buffer to
accommodate longer string. Since this macro is used in multiple files, we
move it into arch/powerpc/include/asm/config.h.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add one more argument to call function readline_into_buffer().
Fix print SPD format for negative values.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Only the first DIMM of first controller should fall back to raw timing
parameters if SPD is missing or corrupted.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Empty slot should be skipped when calculating CAS latency.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Faster DDR3 timing requires parameters exceeding previously defined
range. Extended parameters are fixed. Added some debug messages.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Restructure DDR interleaving option to support 3 and 4 DDR controllers
for 2-, 3- and 4-way interleaving.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Required by JEDEC 79-3E for high speed DDR3.
Also change "CSn disabled" message to debug.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When the DDR3 speed goes higher, we need to utilize fine offset
from SPD.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Some debug registers have non-zero default out of reset. If software is
not setting debug registers, skip writing to them to avoid unnecessary
overriding.
Also add debug messages for workarounds and debug registers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
For the cores with multiple threads, we need to figure out which physical
core a thread belongs. To match the core ids, update PIR registers and
spin tables.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
In case more than 32 bit address is used, the EXT bit should be set.
Need to fix up address map for IFC #CS for 4, also need to move # of IFC
banks into config_mpc85xx.h
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
We have actual topology infomation to find out exactly which core is present.
Calculate the number of cores if not specified.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Freescale's High-End SoC are going to have Integrated Flash controller
(IFC)'s support.
So add IFC LAW target ID support for High-End SoC or corenet SoC.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Freescale's e500v1 and e500v2 cores (used in mpc85xx chips) have some
restrictions on external debugging (JTAG). Need to define define
CONFIG_SYS_PPC_E500_DEBUG_TLB to enable a temporary TLB entry to be
used during boot to work around the limitations.
Enable missed e500v2 SoC i.e. MPC8536, MPC8544, MPC8548 and MPC8572 for
debug support.
Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Erratum A004510 says that under certain load conditions, modified
cache lines can be discarded, causing data corruption.
To work around this, several CCSR and DCSR register updates need to be
made in a careful manner, so that there is no other transaction in
corenet when the update is made.
The update is made from a locked cacheline, with a delay before to flush
any previous activity, and a delay after to flush the CCSR/DCSR update.
We can't use a readback because that would be another corenet
transaction, which is not allowed.
We lock the subsequent cacheline to prevent it from being fetched while
we're executing the previous cacheline. It is filled with nops so that a
branch doesn't cause us to fetch another cacheline.
Ordinarily we are running in a cache-inhibited mapping at this point, so
we temporarily change that. We make it guarded so that we should never
see a speculative load, and we never do an explicit load. Thus, only the
I-cache should ever fill from this mapping, and we flush/unlock it
afterward. Thus we should avoid problems from any potential cache
aliasing between inhibited and non-inhibited mappings.
NOTE that if PAMU is used with this patch, it will need to use a
dedicated LAW as described in the erratum. This is the responsibility
of the OS that sets up PAMU.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
These are not supported as individual build targets, but instead
are supported by another target.
The dead p4040 defines in particular had bitrotted significantly.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The P3060 was cancelled before it went into production, so there's no point
in supporting it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Unlike previous SOCs, the Freescale P5040 has a fifth DTSEC on the second
Fman, so add the Fman and SerDes macros for that DTSEC.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Currently, for NAND boot for the P1010/4RDB we hard code the DDR
configuration. We can still dynamically set the DDR bus width in
the nand spl so the P1010/4RDB boards can boot from the same
u-boot image
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
P1015 is the same as P1011 and P1016 is the same as P1012 from software
point of view. They have different packages but share SVRs.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
For the powerpc processors with PCIE interface, boot location can be
configured from one PCIE interface by RCW. The processor booting from PCIE
can do without flash for u-boot image. The image can be fetched from another
processor's memory space by PCIE link connected between them.
The processor booting from PCIE is slave, the processor booting from normal
flash memory space is master, and it can help slave to boot from master's
memory space.
When boot from PCIE, slave's core should be in holdoff after powered on for
some specific requirements. Master will release the slave's core at the
right time by PCIE interface.
Environment and requirement:
master:
1. NOR flash for its own u-boot image, ucode and ENV space.
2. Slave's u-boot image is in master NOR flash.
3. Normally boot from local NOR flash.
4. Configure PCIE system if needed.
slave:
1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
2. Boot location should be set to one PCIE interface by RCW.
3. RCW should configure the SerDes, PCIE interfaces correctly.
4. Must set all the cores in holdoff by RCW.
5. Must be powered on before master's boot.
For the master module, need to finish these processes:
1. Initialize the PCIE port and address space.
2. Set inbound PCIE windows covered slave's u-boot image stored in
master's NOR flash.
3. Set outbound windows in order to configure slave's registers
for the core's releasing.
4. Should set the environment variable "bootmaster" to "PCIE1", "PCIE2"
or "PCIE3" using the following command:
setenv bootmaster PCIE1
saveenv
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When compile the slave image for boot from SRIO, no longer need to
specify which SRIO port it will boot from. The code will get this
information from RCW and then finishes corresponding configurations.
This has the following advantages:
1. No longer need to rebuild an image when change the SRIO port for
boot from SRIO, just rewrite the new RCW with selected port,
then the code will get the port information by reading new RCW.
2. It will be easier to support other boot location options, for
example, boot from PCIE.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Get rid of the SRIOBOOT_MASTER build target, and to support for serving as
a SRIO boot master via environment variable. Set the environment variable
"bootmaster" to "SRIO1" or "SRIO2" using the following command:
setenv bootmaster SRIO1
saveenv
The "bootmaster" will enable the function of the SRIO boot master, and
this has the following advantages compared with SRIOBOOT_MASTER build
configuration:
1. Reduce a build configuration item in boards.cfg file.
No longer need to build a special image for master, just use a
normal target image and set the "bootmaster" variable.
2. No longer need to rebuild an image when change the SRIO port for
boot from SRIO, just set the corresponding value to "bootmaster"
based on the using SRIO port.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This erratum applies to the following SoCs:
P4080 rev 1.0, 2.0, fixed in rev 3.0
P2041 rev 1.0, 1.1, fixed in rev 2.0
P3041 rev 1.0, 1.1, fixed in rev 2.0.
Workaround for erratum NMG_CPU_A011 is enabled by default. This workaround
may degrade performance. P4080 erratum CPU22 shares the same workaround.
So it is always enabled for P4080. For other SoCs, it can be disabled by
hwconfig with syntax:
fsl_cpu_a011:disable
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The code first aligns the SP to 16 then subtract 8, making it
8 bytes aligned. Furthermore the initial stack frame not
quite correct either.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Andy Fleming <afleming@freescale.com>
PowerPC mandates SP to be 16 bytes aligned.
Furthermore, a stack frame is added, pointing to the reset vector
which may in the way when gdb is walking the stack because
the reset vector may not accessible depending on emulator settings.
Also use a temp register so gdb doesn't pick up intermediate values.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Prototype declaration of I/O operation functions are not correct. as both
'extern' and function definition are at same place.
Chage protoype declaration as static.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Return type of in_8, in_be16 and in_le16 should not be'int'. Update it to type
u8/u16/u32.
Although 'unsigned' for in_be32 and in_le32 is correct. But to make return type
uniform across the file changed to u32
Similarly, parameter passed to out_8, out_be16, out_le16 ,out_be32 & out_le32
should not be 'int'.Change it to type u8/u16/u32.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
All the global flag defines are the same across all arches. So unify them
in one place, and add a simple way for arches to extend for their needs.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The SET_PCI_LIODN() macro takes a compatible property string as a parameter, so that it knows
which PCI device tree node to look for. The calls to these macros are using a hard-coded string,
but we already have the CONFIG_SYS_FSL_PCIE_COMPAT macro which contains the same string, so we
should use that.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Commit 48f6a5c34 removed E bit. BSC9130/1 were left out due to patch apply
timing. Remove them now.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The BR_PHYS_ADDR(x) macro was missing parentheses around "x" in the macro
definition, so callers had to supply their own parenthesis.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
fsl_ddr_get_dimm_params() should be wrapped by
CONFIG_SYS_DDR_RAW_TIMING, otherwise, when using fixed_sdram() instead of
using SPD, it will cause compile error.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The fix for errata workaround is to avoid covering physical address
0xff000000 to 0xffffffff during the implementation. Early commit eb672e92
works until DDR size exceeds 4GB. This fix works for DDR size up to 64GB.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
* 'next' of git://git.denx.de/u-boot:
MPC8xx: Fixup warning in arch/powerpc/cpu/mpc8xx/cpu.c
doc: cleanup - move board READMEs into respective board directories
net: sh_eth: add support for SH7757's GETHER
net: sh_eth: modify the definitions of regsiter
net: sh_eth: add SH_ETH_TYPE_ condition
net: sh_eth: clean up for the SH7757's code
net: fec_mxc: Fix MDC for xMII
net: fec_mxc: Fix setting of RCR for xMII
net: nfs: make NFS_TIMEOUT configurable
net: Inline the new eth_setenv_enetaddr_by_index function
net: allow setting env enetaddr from net device setting
net/designware: Consecutive writes to the same register to be avoided
CACHE: net: asix: Fix asix driver to work with data cache on
net: phy: micrel: make ksz9021 phy accessible
net: abort network initialization if the PHY driver fails
phylib: phy_startup() should return an error code on failure
net: tftp: fix type of block arg to store_block
Signed-off-by: Wolfgang Denk <wd@denx.de>
cpu.c: In function ‘check_CPU’:
cpu.c:256:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Subject slightly changed.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested on TQM855MDCBAB7-T66.102 (MPC855T at 66 MHz) and
TQM860LDB0A3-T50.202 (MPC860T at 50MHz).
Tested-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
An empty flush_dcache_range() was added into MPC83xx and MPC85xx to
work with drivers shared with other architecture. However, it is
compiled only if USB is set, but it is required for other drivers
(FSL_ESDHC), too.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Andy Fleming <afleming@gmail.com>
CC: Dirk Behme <dirk.behme@de.bosch.com>
CC: Marek Vasut <marex@denx.de>
CC: Wolfgang Denk <wd@denx.de>
Added MPC83xx version.
Signed-off-by: Wolfgang Denk <wd@denx.de>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/mpc85xx: Fix Handling the lack of L2 cache on P2040/P2040E
powerpc/mpc85xx: Workaround for erratum CPU_A011
powerpc/mpc85xx: Ignore E bit for SVR_SOC_VER()
powerpc/P4080: Check SVR for CPU22 workaround
lib/powerpc: addrmap_phys_to_virt() should return a pointer
powerpc/85xx: clean up P1022DS board configuration header file
powerpc/85xx: fdt_set_phy_handle() should return an error code
powerpc/85xx: minor clean-ups to the P2020DS board header file
powerpc/p1010rdb: add readme document for p1010rdb
powerpc/mpc85xx:NAND_SPL:Avoid IFC/eLBC Base address setting
powerpc/mpc85xx:Add debugger support for e500v2 SoC
powerpc/85xx:Fix NAND code base to support debugger
powerpc/85xx:Make debug exception vector accessible
powerpc/85xx:Fix MSR[DE] bit in MSR to support debugger
PATCH 1/4][v4] doc:Add documentation for e500 external debugger support
powerpc/p1010rdb: update mux config of p1010rdb board
powerpc/mpc85xx:Add BSC9131 RDB Support
powerpc/mpc85xx:Add BSC9131/BSC9130/BSC9231 Processor Support
powerpc/85xx: Add USB device-tree fixup for various platforms
Signed-off-by: Wolfgang Denk <wd@denx.de>
Erratum NMG_CPU_A011 applies to P4080 rev 1.0, 2.0, fixed in rev 3.0.
It also applies to P3041 rev 1.0, 1.1, P2041 rev 1.0, 1.1. It shares the
same workaround as erratum CPU22. Rearrange registers usage in assembly
code to avoid accidental overwriting.
Signed-off-by: York Sun <yorksun@freescale.com>
We don't care E bit of SVR in most cases. Clear E bit for SVR_SOC_VER().
This will simplify the coding. Use IS_E_PROCESSOR() to identify SoC with
encryption. Remove all _E entries from SVR list and CPU list.
Signed-off-by: York Sun <yorksun@freescale.com>
addrmap_phys_to_virt() converts a physical address (phys_addr_t) to a
virtual address, so it should return a pointer instead of an unsigned long.
Its counterpart, addrmap_virt_to_phys(), takes a pointer, so now they're
orthogonal.
The only caller of addrmap_phys_to_virt() converts the return value to
a pointer anyway.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
During NAND_SPL boot, base address and different register are programmed
default by corresponding NAND controllers(eLBC/IFC). These settings are
sufficient enough for NAND SPL.
Avoid updating these register.They will be programmed during NAND RAMBOOT.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Freescale's e500v1 and e500v2 cores (used in mpc85xx chips) have some
restrictions on external debugging (JTAG).
So define CONFIG_SYS_PPC_E500_DEBUG_TLB to enable a temporary TLB entry to be
used during boot to work around the limitations.
Please refer doc/README.mpc85xx for more information
Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Update NAND code base to ovecome e500 and e500v2's second limitation i.e. IVPR
+ IVOR15 should be valid fetchable OP code address.
As NAND SPL does not compile vector table so making sure IVOR + IVOR15 points to
any fetchable valid data
Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Marius Grigoras <marius.grigoras@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Debugging of e500 and e500v1 processer requires debug exception vecter (IVPR +
IVOR15) to have valid and fetchable OP code.
1) While executing in translated space (AS=1), whenever a debug exception is
generated, the MSR[DS/IS] gets cleared i.e. AS=0 and the processor tries to
fetch an instruction from the debug exception vector (IVPR + IVOR15); since now
we are in AS=0, the application needs to ensure the proper TLB configuration to
have (IVOR + IVOR15) accessible from AS=0 also.
Create a temporary TLB in AS0 to make sure debug exception verctor is
accessible on debug exception.
2) Just after relocation in DDR, Make sure IVPR + IVOR15 points to valid opcode
Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Marius Grigoras <marius.grigoras@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Debugging of e500 and e500v1 processer requires MSR[DE] bit to be set always.
Where MSR = Machine State register
Make sure of MSR[DE] bit is set uniformaly across the different execution
address space i.e. AS0 and AS1.
Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Catalin Udma <catalin.udma@freescale.com>
Signed-off-by: Marius Grigoras <marius.grigoras@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
- BSC9131 is integrated device that targets Femto base station market.
It combines Power Architecture e500v2 and DSP StarCore SC3850 core
technologies with MAPLE-B2F baseband acceleration processing elements.
- BSC9130 is exactly same as BSC9131 except that the max e500v2
core and DSP core frequencies are 800M(these are 1G in case of 9131).
- BSC9231 is similar to BSC9131 except no MAPLE
The BSC9131 SoC includes the following function and features:
. Power Architecture subsystem including a e500 processor with 256-Kbyte shared
L2 cache
. StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache
. The Multi Accelerator Platform Engine for Femto BaseStation Baseband
Processing (MAPLE-B2F)
. A multi-standard baseband algorithm accelerator for Channel Decoding/Encoding,
Fourier Transforms, UMTS chip rate processing, LTE UP/DL Channel processing,
and CRC algorithms
. Consists of accelerators for Convolution, Filtering, Turbo Encoding,
Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix Inversion
operations
. DDR3/3L memory interface with 32-bit data width without ECC and 16-bit with
ECC, up to 400-MHz clock/800 MHz data rate
. Dedicated security engine featuring trusted boot
. DMA controller
. OCNDMA with four bidirectional channels
. Interfaces
. Two triple-speed Gigabit Ethernet controllers featuring network acceleration
including IEEE 1588. v2 hardware support and virtualization (eTSEC)
. eTSEC 1 supports RGMII/RMII
. eTSEC 2 supports RGMII
. High-speed USB 2.0 host and device controller with ULPI interface
. Enhanced secure digital (SD/MMC) host controller (eSDHC)
. Antenna interface controller (AIC), supporting three industry standard
JESD207/three custom ADI RF interfaces (two dual port and one single port)
and three MAXIM's MaxPHY serial interfaces
. ADI lanes support both full duplex FDD support and half duplex TDD support
. Universal Subscriber Identity Module (USIM) interface that facilitates
communication to SIM cards or Eurochip pre-paid phone cards
. TDM with one TDM port
. Two DUART, four eSPI, and two I2C controllers
. Integrated Flash memory controller (IFC)
. TDM with 256 channels
. GPIO
. Sixteen 32-bit timers
The DSP portion of the SoC consists of DSP core (SC3850) and various
accelerators pertaining to DSP operations.
This patch takes care of code pertaining to power side functionality only.
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Akhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Rajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
The misspelling of "semiconductor" causes some internal copyright analysis
tools to complain.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch conditionally defines flush_dcache_range() and
invalidate_dcache_range() on MPC8xxx, to avoid EHCI complaining,
resulting in the following output:
$ ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu- ./MAKEALL MPC8572DS
Configuring for MPC8572DS board...
make: *** [u-boot] Error 1
powerpc-linux-gnu-size: './u-boot': No such file
e1000.c: In function ‘e1000_initialize’:
e1000.c:5264:13: warning: assignment from incompatible pointer type [enabled by default]
tsec.c: In function ‘tsec_initialize’:
tsec.c:638:12: warning: assignment from incompatible pointer type [enabled by default]
drivers/usb/host/libusb_host.o: In function `ehci_td_buffer':
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:186: undefined reference to `flush_dcache_range'
drivers/usb/host/libusb_host.o: In function `ehci_submit_async':
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:346: undefined reference to `flush_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:348: undefined reference to `flush_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:349: undefined reference to `flush_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:372: undefined reference to `invalidate_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:374: undefined reference to `invalidate_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:376: undefined reference to `invalidate_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:386: undefined reference to `invalidate_dcache_range'
make: *** [u-boot] Error 1
--------------------- SUMMARY ----------------------------
Boards compiled: 1
Boards with errors: 1 ( MPC8572DS )
----------------------------------------------------------
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Fix this:
ether_scc.c: In function 'mpc82xx_scc_enet_initialize':
ether_scc.c:377:14: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
ether_fcc.c: In function 'fec_initialize':
ether_fcc.c:453:15: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
ether_fcc.c: In function 'fec_initialize':
ether_fcc.c:390:15: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
fec.c: In function 'mpc8220_fec_recv':
fec.c:791:9: warning: passing argument 1 of 'NetReceive' discards qualifiers from pointer target type
include/net.h:438:13: note: expected 'uchar *' but argument is of type 'volatile uchar *'
fec.c: In function 'mpc8220_fec_initialize':
fec.c:839:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>