Currently, dram_init() code relies on the fact the DRAM size
configuration exists in the SG_MEMCONF register.
This will no longer be true for a planned new SoC, which will
replace SG_MEMCONF with a different register.
Refactor the hook in a more generic way.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Until the last SoC, the register addresses have been hard-coded because
they are always constant. For a planned new SoC, the register bases
will be completely changed. I insist on supporting multiple SoCs/boards
by a single defconfig (uniphier_v8_defconfig) since duplicating similar
defconfig files is a maintenance burden. The base addresses must be
fixed-up at run-time somehow.
Previously, the board init code identified the SoC by reading out the
SG_REVISION register. This is much easier than parsing DT.
You cannot do it any more because the base address of SG will be
changed. The SG_REVISION register exists to read out the SoC ID, but
you never know its address before identifying the SoC. Oh well.
So, the possible solution is to parse the DT, and find out the node
with "*-soc-glue" compatible string. Then, sg_base is set to the value
of the "reg" property. The sc_base is set up likewise.
It is worth noting a pit-fall. Having sc_base and sg_base in the global
scope will make the life easier, but the global variables are poorly
supported before the relocation. In fact, the .bss section overwraps
with DT. Allocating them in the .bss section would break DT. So, I gave
dummy initializers to assign them in the .data section.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The SC_* macros represent the address of SysCtrl registers.
For a planned new SoC, its base address will be changed.
Turn the SC_* macros into the offset from the base address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The SG_* macros represent the address of SoC-glue registers.
For a planned new SoC, its base address will be changed.
Turn the SG_* macros into the offset from the base address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The planned new SoC does not have SBC (System Bus Controller) block.
Make boot_is_swapped() an optional hook.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If CONFIG_MICRO_SUPPORT_CARD is enabled, U-Boot initialize SBC
(System Bus Controller), which may not be really necessary.
Check the "socionext,uniphier-system-bus" node in DT run-time.
If and only if it is found and its "status" property is okay,
initialize the SBC block.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If CONFIG_MICRO_SUPPORT_CARD is enabled, U-Boot tries to get access
to the devices on the support card, which may not actually exist.
Check the DT and search for the on-board devices run-time. If the
nodes are not found in DT, then disable the code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This file calls readl(), so needs to include <linux/io.h>.
Currently, it relies on someone else including it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now that 64-bit SoCs of this SoC family no longer support SPL,
this Makefile can be slightly simpler.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The .boot_device_fixup() is only called by SPL.
Now that 64-bit SoCs of this SoC family no longer support SPL,
debug-uart-ld20.c is never compiled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move the sg_set_pinsel macro to arch/arm/mach-uniphier/arm32/debug_ll.S
since it is not used anywhere else.
Move the C functions sg_set_{pinsel,iectrl} to debug-uart.c since they
are not used anywhere else.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
debug_uart_init() is called from spl_board_init(), which is only
compiled for SPL. For U-boot proper, _debug_uart_init() is unreachable,
so dropped by the dead code elimination.
Now that 64-bit SoCs of this SoC family no longer support SPL,
debug-uart-ld20.c is never compiled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This file calls readl(), so needs to include <linux/io.h>.
Currently, it relies on someone else including it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Some users might want to modify 'bootcmd' at compile-time by editing
include/configs/uniphier.h, but overwriting it at run-time makes it
impossible.
Instead, set 'bootdev' at run-time, which contains the boot device the
system is booting from, then indirectly reference it from 'bootcmd'.
It is up to users whether to override 'bootcmd'.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
NAND flavors, like serial and parallel, have a lot in common and would
benefit to share code. Let's move raw (parallel) NAND specific code in a
raw/ subdirectory, to ease the addition of a core file in nand/ and the
introduction of a spi/ subdirectory specific to SPI NANDs.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The MIO clock is enabled by default, and the STDMAC clock is
enabled by the clk driver. The ad-hoc way to enable the clock
is no longer needed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Another round of sorting Kconfig entries aplhabetically.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Switch to the distro boot for UniPhier platform.
- Remove the environment vairalbes used to load images from raw
block devices.
- Keep the command to download images via tftp. This will be
useful to boot the kernel when no valid kernel image is ready
yet in the file system.
- Use root.cpio.gz instead of root.cpio.uboot because we always know
the file size of the init ramdisk; it is loaded via either a file
system or network.
- Rename fit_addr_r to kernel_addr_r, which the distro command
checks to get the load address of FIT image.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The 'bd' is passed in ft_board_setup() as the second argument.
Replace 'gd->bd' with 'bd'.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
For booting Linux in the generic distro mechanism, cmd/pxe.c
retrieves the FDT file name from "fdtfile" environment variable.
Rename "fdt_file" to "fdtfile" for easier migration to distro boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently CPU_V7 kconfig symbol supports only ARMv7A architectures under
armv7 folder. This led to a misconception of creating separate folders
for armv7m and armv7r. There is no reason to create separate folder for
other armv7 based architectures when it can co-exist with few Kconfig
symbols.
As a first step towards a common folder, rename CPU_V7 as CPUV7A. Later
separate Kconfig symbols can be added for CPU_V7R and CPU_V7M and
can co exist in the same folder.
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Suggested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Replace the psci_save_target_pc call by the new function
psci_save(cpu, pc,context_id)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I do not see a good reason to do this by a CONFIG option that affects
all SoCs. The ram_size can be adjusted by dram_init() at run-time.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
LD20 / PXs3 boards are equipped with a large amount of memory beyond
the 32 bit address range. U-Boot relocates itself to the end of the
available RAM.
This is a problem for DMA engines that only support 32 bit physical
address, like the SDMA of SDHCI controllers.
In fact, U-Boot does not need to run at the very end of RAM. It is
rather troublesome for drivers with DMA engines because U-Boot does
not have API like dma_set_mask(), so DMA silently fails, making the
driver debugging difficult.
Hide the memory region that exceeds the 32 bit address range. It can
be done by simply carving out gd->ram_size. It would also possible to
override get_effective_memsize() or to define CONFIG_MAX_MEM_MAPPED,
but dram_init() is a good enough place to do this job.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
It is tedious to define both mask and bit-shift. <linux/bitfield.h>
provides a convenient way to get access to register fields with a
single shifted mask.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use DIV_ROUND_CLOSEST(). To make the JK value even more precise,
I used a bigger coefficient, then divide it by 512.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 682e09ff9f ("ARM: uniphier: add PLL init code for LD20 SoC")
missed to write the computed value to the SSCPLLCTRL2 register.
Fixes: 682e09ff9f ("ARM: uniphier: add PLL init code for LD20 SoC")
Signed-off-by: Dai Okamura <okamura.dai@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fix the link error for the combination of
CONFIG_ARCH_UNIPHIER_LD11=n
CONFIG_ARCH_UNIPHIER_LD20=n
CONFIG_ARCH_UNIPHIER_PXS3=y
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Remove unnecessary DECLARE_GLOBAL_DATA_PTR and header includes.
<common.h> has been replaced with <linux/errno.h> and <linux/printk.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This work-around has been here in U-Boot because the AIDET and GPIO
drivers were missing in the upstream Linux. Both are now available
in Linus' tree:
- drivers/irqchip/irq-uniphier-aidet.c
- drivers/gpio/gpio-uniphier.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit dd74b945af ("ARM: uniphier: use pr_() instead of printf()
where appropriate"), but I missed to update this file for some reason.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
UniPhier 32-bit SoCs use CONFIG_SPL_OF_CONTROL. So, many nodes must
be marked as dm-pre-reloc to prevent fdtgrep from stripping them off.
Sprinkling U-Boot-specific properties all over the place is painful
because DT files are synced with Linux from time to time.
Split u-boot,dm-pre-reloc out to uniphier-v7-u-boot.dtsi, which is
appended to UniPhier V7 DTS before the build.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The option is never enabled by anyone. Remove the code surrounded
by its ifdef. This should be handled by the clock/reset drivers.
CONFIG_UNIPHIER_ETH in scripts/config_whitelist.txt will be dropped
by the next resync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
ARCH_UNIPHIER_V8_MULTI depends on !SPL, so the default may be hidden.
Use a clearer default.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When we import code from Linux, with regular re-sync planned, we want
to use printk() and pr_*(). U-Boot does not support them in a clean
way. So, people end up with local macros, or compat headers here and
there, then we occasionally see build errors of definition conflicts.
We have include/linux/compat.h, but putting all sorts of unrelated
things into a single header is just a temporal workaround. Hence this
patch, to find the best home for all printk variants. If you want to
use printk() and friends, please include <linux/printk.h>. This header
is self-contained, and pulls in only a few headers.
When I was testing this clean-up, I noticed the image size exceeded
its platform limit on some boards. This is because all pr_*() that
were previously defined as no-op in include/linux/mtd/mtd.h (unless
CONFIG_MTD_DEBUG is set), are now enabled.
To make such boards happy, this commit also implements CONFIG_LOGLEVEL.
The concept is similar to the kernel parameter "loglevel". (Actually,
the Kconfig help message was taken from kernel-paremeter.txt of Linux)
Messages with a loglevel smaller than console loglevel will be printed.
The difference is the loglevel is build-time determined. To save the
image size, lower priority pr_*() are compiled out. I set the default
of CONFIG_LOGLEVEL to 6, i.e. pr_notice and higher priority messages
are compiled in.
I adjusted CONFIG_LOGLEVEL to avoid build error for some boards.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add in SPL_LOGLEVEL that is the same as LOGLEVEL]
Signed-off-by: Tom Rini <trini@konsulko.com>
Starting from PXs3, the bit fields of RSTCTRL, CLKCTRL registers
will change every SoC. There is no more point to define bitfields
in the common header file.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The main difference between Pro4 and PXs2/LD6b is the Denali NAND
IP version. This is now distinguished by DT. Merge the two defconfig
files into uniphier_v7_defconfig.
Update the README.uniphier too.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This imply was added when the option was moved by the moveconfig tool,
but the intention is not clear. Move it to defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This is now set up by the pinctrl driver when the NAND driver is
probed. Remove the legacy code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The new SoC PXs3 changed the address of PLL, but still uses the
same PLL name. We can not define SC_*PLLCTRL in the common header.
Move them to per-SoC .c file. Also, fix some PLL comments.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The #include <common.h> was added for mdelay(). Later, the declaration
of mdelay was moved to <linux/delay.h> by commit 5bc516ed66 ("delay:
collect {m, n, u}delay declarations to include/linux/delay.h").
There is no need to include <common.h> now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This reverts commit 82d075e79f.
Commit 82d075e79f ("ARM: uniphier: fix ROM boot mode for PH1-sLD3")
was a workaround for sLD3. Now the sLD3 SoC support has been removed.
Revert it to allow to simplify the init code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This reverts commit bcc51c1512.
Commit bcc51c1512 ("ARM: uniphier: move lowlevel debug init code
after page table switch") was intended to support lowlevel debug for
sLD3. Now the sLD3 SoC support has been removed.
Revert it to allow to enable lowlevel debug earlier.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename these
commonly used functions, for consistency. Also add function comments in
common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_NAND
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Sync up a few more, add imply's]
Signed-off-by: Tom Rini <trini@konsulko.com>
As is often the case with SoC development, slightly different
products (i.e. different part number) are developed based on the
same silicon-die. Such fine grained information is unmaintainable.
Also, "SoC:" is a better fit that "CPU:".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
It has been a while since ARM Trusted Firmware supported UniPhier SoC
family. U-Boot SPL was intended as a temporary loader that runs in
secure world. It is a maintenance headache to support two different
boot mechanisms. Secure firmware is realm of ARM Trusted Firmware
and now U-Boot only serves as a non-secure boot loader for UniPhier
ARMv8 SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fix warnings reported by sparse:
- ... was not declared. Should it be static?"
- cast to restricted __be32
While fixing those, the type conflict of cci500_init() was found.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
It is good practice to include common.h as the first header. This ensures
that required features like the DECLARE_GLOBAL_DATA_PTR macro,
configuration options and common types are available.
Fix up some files which currently don't do this. This is necessary because
driver model will soon start using global data and configuration in the
dm/read.h header file, included via dm.h. The gd->fdt_blob value will be
used to access the device tree and CONFIG options will be used to
determine whether to support inline functions in the header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
This header includes things that are needed to make driver build. Adjust
existing users to include that always, even if other dm/ includes are
present
Signed-off-by: Simon Glass <sjg@chromium.org>
When booting from ARM Trusted Firmware, U-Boot runs in EL1-NS.
The boot flow is as follows:
BL1 -> BL2 -> BL31 -> BL33 (i.e. U-Boot)
This boot sequence works fine for LD11 SoC (Cortex-A53), but LD20
SoC (Cortex-A72) hangs in U-Boot. The solution I found is to
read sctlr_el1 and write back the value as-is. This should be
no effect, but surprisingly fixes the problem for LD20 to boot.
I do not know why.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In order to be able to migrate the various SoC EHCI CONFIG options we
first need to finish the switch from CONFIG_USB_EHCI to
CONFIG_USB_EHCI_HCD.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The SCP (System Control Processor) or what we call STM (Stand-by
MPU) is integrated in LD4, Pro4, sLD8, LD6b, LD11, and LD20.
For these SoCs, show the information if STM is enabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This configuration is supposed to be used with ARM Trusted Firmware,
so the SYSTEM_RESET is implemented in BL31. Invoke PSCI instead of
U-Boot's own reset code because we need to coordinate with SCP
(System Control Processor) for the system-level power management.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Commit 04cd4e7215 ("ARM: uniphier: remove DRAM base address from
board parameters") accidentally unset the DRAM_SPARSE flag, and
changed the physical map of the DRAM channels. Revive the original
behavior.
Fixes: 04cd4e7215 ("ARM: uniphier: remove DRAM base address from board parameters")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Shunji Sato <sato.shunji@socionext.com>
Re-use of routines embedded in the Boot ROM requires a function
pointer table for each SoC. This is not nice in terms of the
maintainability in a long run.
Implement simple eMMC load APIs that are commonly used for LD11,
LD20, and hopefully future SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
For LD11 and LD20 SoCs, the RST_n pin is asserted by default. If
the EXT_CSD[162], bit[1:0] (RST_n_ENABLE) is fused, the eMMC device
would stay in the reset state until its RST_n pin is deasserted by
software.
Currently, this is cared by an ad-hoc way because the eMMC hardware
reset provider is not supported in U-Boot for now. This code should
be re-written once the "mmc-pwrseq-emmc" binding is supported.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If the DRAM clock duty does not meet the allowable tolerance,
it is marked in an efuse register. If the register is fused,
the boot code should compensate for the DRAM clock duty error.
Signed-off-by: Kotaro Hayashi <hayashi.kotaro@socionext.com>
[masahiro: simplify code, add git-log]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This parameter is redundant because we can know the number of
channels by checking if dram_ch[2].size is zero.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The current implementation has ugly switch statements here and there,
and duplicates similar code. Rework it using table lookups for SoC
data and reduce code duplication.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The spl_boot_mode() is unrelated to the other code in this file.
Besides, this function is only called from common/spl/spl_mmc.c,
so it is reasonable to guard with CONFIG_SPL_MMC_SUPPORT.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, arch/arm/mach-uniphier/boot-mode/boot-mode.c is messed up
with unrelated code; there is no reason why the "mmcsetn" command
must be placed in this file.
Split out the MMC code into arch/arm/mach-uniphier/mmc-first-dev.c.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The base address of each DRAM channel can be calculated from other
parameters, so does not need hard-coding. What we need is the size
of each DRAM channel and DRAM_SPARSE flag to decide the start address
of DRAM channel 1.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit 26b09c022a ("ARM: uniphier: move SBC and Support Card
init code to U-Boot proper"), the System Bus is initialized by
board_init(). The show_board_info() is called from board_init_f()
by default, so the revision register of the Micro Support Card may
not be accessed at this point. Show its revision after the System
Bus is initialized.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now the "for" loop here iterates on the detected memory banks.
It must skip unused DRAM banks.
Fixes: c995f3a3c5 ("ARM: uniphier: use gd->bd->bi_dram for memory reserve on LD20 SoC")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If SG_MEMCONF_CH2_DISABLE bit is set, the DRAM channel 2 is unused.
The register settings for the ch2 should be ignored.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.
During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will
make the code more readable. Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.
This commit was created as follows:
[1] Edit "default n" to "default y" in the config entry in
common/Kconfig.
[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"
[3] Rename the instances in defconfigs by the following:
find . -path './configs/*_defconfig' | xargs sed -i \
-e '/CONFIG_SYS_NO_FLASH=y/d' \
-e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'
[4] Change the conditionals by the following:
find . -name '*.[ch]' | xargs sed -i \
-e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
-e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
-e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
-e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'
[5] Modify the following manually
- Rename the rest of instances
- Remove the description from README
- Create the new Kconfig entry in drivers/mtd/Kconfig
- Remove the old Kconfig entry from common/Kconfig
- Remove the garbage comments from include/configs/*.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
CONFIG_CMD_ZIP is not defined by any board. I am moving
CONFIG_CMD_UNZIP to defconfig files except UniPhier SoC family.
I am the maintainer of UniPhier platform, so I know "select CMD_UNZIP"
is better for this platform.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
It seems more readable to use arrays to get SoC specific parameters
instead of the crappy switch statement.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
For LD20 SoC, the last 64 byte of each DRAM bank is used for the
dynamic training of DRAM PHY. The regions must be reserved in DT to
prevent the kernel from using them. Now gd->bd->bi_dram reflects
the actual memory banks. Just use it instead of getting access to
the board parameters.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
