This patch extends the imx6 clock code to enable or disable the EIM
slow clock, which in necessary when one wants to use EIM interface t
o read/write from external memory (e.g. NOR).
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
The DDR calibration routines are gated by conditionals for the
i.MX6DQ SOCs, but with the use of the sysinfo parameter, these
are usable on at least i.MX6SDL and i.MX6SL variants with DDR3.
Also, since only the Novena board currently uses the dynamic
DDR calibration routines, these routines waste space on other
boards using SPL.
Add a KConfig entry to allow boards to selectively include the
DDR calibration routines.
Signed-off-by: Eric Nelson <eric@nelint.com>
Add routine mmdc_read_calibration() to return the output of DDR
calibration. This can be used for debugging or to aid in construction
of static memory configuration.
This routine will be used in a subsequent patch set adding a virtual
"mx6memcal" board, but could also be useful when gathering statistics
during an initial production run.
Signed-off-by: Eric Nelson <eric@nelint.com>
The DDR calibration routines have scattered support for bus
widths other than 64-bits:
-- The mmdc_do_write_level_calibration() routine assumes the
presence of PHY1, and
-- The mmdc_do_dqs_calibration() routine tries to determine
whether one or two DDR PHYs are active by reading MDCTL.
Since a caller of these routines must have a valid struct mx6_ddr_sysinfo
for use in calling mx6_dram_cfg(), and the bus width is available in the
"dsize" field, use this structure to inform the calibration routines which
PHYs are active.
This allows the use of the DDR calibration routines on CPU variants
like i.MX6SL that only have a single MMDC port.
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add constants for the MPZQLP2CTL DDR register for both
banks to allow setting the LPDDR2 timing values in
.cfg files using a named constant instead of hex addresses
as is currently done in mx6slevk and other board files.
Signed-off-by: Eric Nelson <eric@nelint.com>
The ipu has two display interfaces. Make the used one a parameter
in struct display_info_t instead of using unconditionally DI0.
DI0 is the default setting.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
As PSCI and secure monitor firmware framework are enabled, this patch is
to support loading 32-bit OS in such case. The default target exception
level returned to U-Boot is EL2, so the corresponding work to switch to
AArch32 EL2 and jump to 32-bit OS are done in U-Boot and secure firmware
together.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Spin-table method is used for secondary cores to load 32-bit OS. The
architecture information will be got through checking FIT image and
saved in the os_arch element of spin-table, then the secondary cores
will check os_arch and jump to 32-bit OS or 64-bit OS automatically.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
To support loading a 32-bit OS, the execution state will change from
AArch64 to AArch32 when jumping to kernel.
The architecture information will be got through checking FIT image,
then U-Boot will load 32-bit OS or 64-bit OS automatically.
Signed-off-by: Ebony Zhu <ebony.zhu@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The QorIQ LS2088A SoC is built on layerscape architecture.
It is similar to LS2080A SoC with some differences like
1)Timer controller offset is different
2)It has A72 cores
3)It supports TZASC module
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Timer controller base address has been changed from
LS2080A SoC (and its personalities) to new SoCs like
LS2088A, LS1088A.
Use SVR based timer base address detection to avoid compile time #ifdef.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
With the move to arch/arm/mach-omap2 there are now very few uses of
CONFIG_OMAP_COMMON and further they can all be replaced with
CONFIG_ARCH_OMAP2, so do so.
Signed-off-by: Tom Rini <trini@konsulko.com>
Detect the board very early and avoid reading eeprom multiple times.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is similar to Commit 93e6253d11 ("ARM: OMAP4/5: Centralize
early clock initialization") that was done for OMAP4+, reflecting the same
for AM33xx and AM43xx SoCs to centralize clock initialization.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add setup_early_clocks that calls setup_clocks_for_console for
ti81xx]
Signed-off-by: Tom Rini <trini@konsulko.com>
Set the appropriate bits in the interface config register based
on the SPI_ mode flags.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Highlights this time around:
- x86 efi_loader support
- hello world efi test case
- network device name is now representative
- terminal output reports modes correctly
- fix psci reset for ls1043/ls1046
- fix efi_add_runtime_mmio definition for x86
- efi_loader support for ls2080
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=xmR3
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2016-11-17
Highlights this time around:
- x86 efi_loader support
- hello world efi test case
- network device name is now representative
- terminal output reports modes correctly
- fix psci reset for ls1043/ls1046
- fix efi_add_runtime_mmio definition for x86
- efi_loader support for ls2080
On ls2080 we have a separate network fabric component which we need to
shut down before we enter Linux (or any other OS). Along with that also
comes configuration of the fabric using a description file.
Today we always stop and configure the fabric in the boot script and
(again) exit it on device tree generation. This works ok for the normal
booti case, but with bootefi the payload we're running may still want to
access the network.
So let's add a new fsl_mc command that defers configuration and stopping
the hardware to when we actually exit U-Boot, so that we can still use
the fabric from an EFI payload.
For existing boot scripts, nothing should change with this patch.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
[agraf: Fix x86 build]
According to design team, we need to set REFTOP_VBGADJ
in PMU MISC0 according to the REFTOP_TRIM[2:0] fuse. the
actually table is as below:
'000" - set REFTOP_VBGADJ[2:0] to 3'b000
'001" - set REFTOP_VBGADJ[2:0] to 3'b001
'010" - set REFTOP_VBGADJ[2:0] to 3'b010
'011" - set REFTOP_VBGADJ[2:0] to 3'b011
'100" - set REFTOP_VBGADJ[2:0] to 3'b100
'101" - set REFTOP_VBGADJ[2:0] to 3'b101
'110" - set REFTOP_VBGADJ[2:0] to 3'b110
'111" - set REFTOP_VBGADJ[2:0] to 3'b111
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Add support for SD1 with level shifters bootmode.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
While we setup the mmu initially we mark set_section_dcache with
DCACHE_OFF flag. In case of non-LPAE mode the DCACHE_OFF macro
is rightly defined with TTB_SECT_XN_MASK set so as to mark all the
4GB XN. In case of LPAE mode XN(Execute-never) bit is not set with
DCACHE_OFF. Hence XN bit is not set by default for DCACHE_OFF which
keeps all the regions execute okay and this leads to random speculative
fetches in random memory regions which was eventually caught by kernel
omap-l3-noc driver.
Fix this to mark the regions as XN by default.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
SoC-specific logic may be required for all forms of cache-wide
operations; invalidate and flush of both dcache and icache (note that
only 3 of the 4 possible combinations make sense, since the icache never
contains dirty lines). This patch adds an optional hook for all
implemented cache-wide operations, and renames the one existing hook to
better represent exactly which operation it is implementing. A dummy
no-op implementation of each hook is provided.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add support for rk3288 dram capacity auto detect, support DDR3 and
LPDDR3, DDR2 is not supported.
The program will automatically detect:
- channel number
- rank number
- column address number
- row address number
The dts file do not need to describe those info after apply this patch.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
This function is called from outside the driver. It should be placed into
common SoC code. Move it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This function is called from outside the driver. It should be placed into
common SoC code. Move it.
Also rename the driver symbol to be more consistent with the other rockchip
clock drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This function is called from outside the driver. It should be placed into
common SoC code. Move it.
Also rename the driver symbol to be more consistent with the other rockchip
clock drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The A80 has SID e-fuses. Like other newer SoCs, the actual e-fuses
are at an offset of 0x200 within the SID address space.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This is a cleaned up version set_pll() from Allwinner's boot0 source
(bootloader/basic_loader/bsp/bsp_for_a80/common/common.c).
[wens@csie.org: Added commit message; style cleanup]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
On sun9i, the GTBUS manages transaction priority and bandwidth
for multiple read ports when accessing DRAM. The initialisation
mirrors the settings from Allwinner's boot0 for now, even though
this may not be optimal for all applications (e.g. headless
systems might want to give priority to IO modules).
Adding a common callout to gtbus_init() from the SPL clock init
with a weakly defined implementation in sunxi/clock.c to fallback
to for platforms that don't require this.
[wens@csie.org: Moved gtbus_sun9i.c to arch/arm/mach-sunxi/; style cleanup]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This adds DRAM initialisation code for sun9i, which calculates the
appropriate timings based on timing information for the supplied
DDR3 bin and the clock speeds used.
With this DRAM setup, we have verified DDR3 clocks of up to 792MHz
(i.e. DDR3-1600) on the A80-Q7 using a dual-channel configuration.
[wens@csie.org: Moved dram_sun9i.c to arch/arm/mach-sunxi/; style cleanup]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[hdegoede@redhat.com: Drop some huge non-documenting #if 0 ... #endif blocks]
[hdegoede@redhat.com: Fix checkpatch warnings]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Mostly by adding MACH_SUN50I to some existing #ifdefs enable support
for the the HCI0 USB host controller on the A64.
Fix up some minor 64-bit hiccups on the way.
Add the bare minimum DT bits to the A64 .dtsi and enable the controllers
and the PHY on the Pine64.
This is limited to the first USB controller at the moment, which is
connected to the lower USB socket on the Pine64 board.
[Andre: remove unneeded defines, enable OHCI, add commit message]
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Boot Log for i.CoreM6 DualLite/Solo Starter Kit:
-----------------------------------------------
U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46)
Trying to boot from MMC1
U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530)
CPU: Freescale i.MX6SOLO rev1.3 at 792MHz
CPU: Industrial temperature grade (-40C to 105C) at 31C
Reset cause: POR
DRAM: 256 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
switch to partitions #0, OK
mmc0 is current device
reading boot.scr
** Unable to read file boot.scr **
reading zImage
6741808 bytes read in 341 ms (18.9 MiB/s)
Booting from mmc ...
reading imx6dl-icore.dtb
30600 bytes read in 19 ms (1.5 MiB/s)
Booting using the fdt blob at 0x18000000
Using Device Tree in place at 18000000, end 1800a787
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
Boot Log for i.CoreM6 Quad/Dual Starter Kit:
--------------------------------------------
U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46)
Trying to boot from MMC1
U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530)
CPU: Freescale i.MX6Q rev1.2 at 792MHz
CPU: Industrial temperature grade (-40C to 105C) at 28C
Reset cause: POR
DRAM: 512 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
icorem6qdl>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add mx7_plugin.S which calls boot rom setup function, generate the second ivt,
and jump back to boot rom.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add mx6_plugin.S which calls boot rom setup function, generate the second ivt,
and jump back to boot rom.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Using PSCI you can not only reset the system, you can also shut it down!
This patch exposes a function to do exactly that to whatever code wants
to make use of it.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
All systems that are running on armv8 are running bare metal with firmware
that implements PSCI running in EL3. That means we don't really need to expose
the hypercall variants of them.
This patch leaves the code in, but makes the code explicit enough to have the
compiler optimize it out. With this we don't need to worry about hvc vs smc
calling convention when calling psci helper functions.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add silicon ID code for AM437x silicon. This can be used to print
the cpu info using CONFIG_DISPLAY_CPUINFO.
Also printing "CPU :" along with cpu name in order to be consistent
with other OMAP platforms.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The normal longjmp command allows for a caller to pass the return value
of the setjmp() invocation. This patch adds that semantic to the arm
implementation of it and adjusts the efi_loader call respectively.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The KeyStone platform has its own clk_get_rate() but its prototype
is different from that of the common-clk (clk-uclass) framework.
Prefix the KeyStone specific implementation with ks_ in order to
avoid name-space conflict.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On some of the SoCs one cannot enable hypervisor mode directly from the
u-boot because the ROM code puts the chip to supervisor mode after it
jumps to boot loader. Hence introduce a weak function which can be
overridden based on the SoC type and switch to hypervisor mode in a
custom way.
Cc: beagleboard-x15@googlegroups.com
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions are needed in UBI/UBIFS on ZynqMP platform (ARM64).
Signed-off-by: Adam Oleksy <adam.oleksy@nokia.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Fix various misspellings of:
* deprecated
* partition
* preceding,preceded
* preparation
* its versus it's
* export
* existing
* scenario
* redundant
* remaining
* value
* architecture
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
At present this is only used on ARM and sandbox, but it is just as
applicable to other architectures. Move the function prototype into the
generic SPL header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move DDR3, DDR4 and related config options to Kconfig and clean up
existing uses.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move DDR3, DDR4 and realted options to Kconfig and clean up existing
uses.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move this option to Kconfig and clean up existing uses.
NUM_DDR_CONTROLLERS is also used by PowerPC SoCs.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move this option to Kconfig and clean up existing uses.
This option is also used by PowerPC SoCs.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move MAX_CPUS option to Kconfig and clean up existing uses for ARM. This
option is used by Freescale Layerscape SoCs.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Pin mux logic has 2 options in priority order, one is through RCW_SRC
and then through RCW_Fields. In case of QSPI booting, RCW_SRC logic
takes the priority for SPI pads and do not allow RCW_BASE and SPI_EXT
to control the SPI muxing. But actually those are DSPI controller's
pads instead of QSPI controller's, so this workaround allows RCW
fields SPI_BASE and SPI_EXT to control relevant pads muxing.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[York Sun: Reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
The core position is not continuous for some SoCs. For example,
valid cores may present at position 0, 1, 4, 5, 8, 9, etc. Some
registers (including boot release register) only count existing
cores. Current implementation of cpu_mask() complies with the
continuous numbering. However, command "cpu status" queries the
spin table with actual core position. Add functions to calculate
core position from core number, to correctly calculate offsets.
Tested on LS2080ARDB and LS1043ARDB.
Signed-off-by: York Sun <york.sun@nxp.com>
By default the SATA IP on the ls1043a/ls1046a SoCs does not
generating coherent/snoopable transactions. This patch enable
it in the SCFG_SNPCNFGCR register along with sata axicc register.
In addition, the dma-coherent property must be set on the SATA
controller nodes.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
[York Sun: Reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
The default values for Port Phy2Cfg register and
Port Phy3Cfg register are better, no need to overwrite them.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For i.MX6, the mux width is 4, not 3. So enlarge the width.
IOMUX_CONFIG_LPSR is changed from 0x8 to 0x20 to not use bit 3 of mux.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
SNVS TAMPER pin and BOOT MODE pins are in SNVS IOMUXC module,
not in IOMUXC, so correct the related registers' offset.
Use IOMUX_CONFIG_LPSR flag for these pins, so we can differentiate
them from iomuxc pins.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: "Benoît Thébaudeau" <benoit.thebaudeau.dev@gmail.com>
Per to design team, on i.MX6UL, the LDO 1.2V bandgap voltage
is 30mV higher, so we need to adjust the REFTOP_VBGADJ(anatop
MISC0 bit[6:4]) setting to 2b'110.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Update memory map address for mx6ull.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Update Clock settings and CCM register map for i.MX6ULL.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add i.MX6ULL major cpu type.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Create a few public APIs which rely on secure world ROM/HAL
APIs for their implementation. These are intended to be used
to reserve a portion of the EMIF memory and configure hardware
firewalls around that region to prevent public code from
manipulating or interfering with that memory.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
rockchip platform have a protocol to pass the the kernel reboot mode to bootloader
by some special registers when system reboot. In bootloader we should read it and take action.
We can only setup boot_mode in board_late_init becasue "setenv" need env setuped.
So add CONFIG_BOARD_LATE_INIT to common header and use a entry "rk_board_late_init"
to replace "board_late_init" in board file.
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Reference to kernel source code, rockchip pwm has three
type, we are using v2 for rk3288 and rk3399, so let's
update the register to sync with pwm_data_v2 in kernel.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Update PPLL to 676MHz and PMU_PCLK to 48MHz, because:
1. 48MHz can make sure the pwm can get exact 50% duty ratio, but 99MHz
can not,
2. We think 48MHz is fast enough for pmu pclk and it is lower power cost
than 99MHz,
3. PPLL 676 MHz and PMU_PCLK 48MHz are the clock rate we are using
internally for kernel,it suppose not to change the bus clock like pmu_pclk
in kernel, so we want to change it in uboot.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
A future patch will implement a clock uclass driver for Tegra. That driver
will call into Tegra's existing clock code to simplify the transition;
this avoids tieing the clock uclass patches into significant refactoring
of the existing custom clock API implementation.
Some of the Tegra clock APIs that manipulate peripheral clocks require
both the peripheral clock ID and parent clock ID to be passed in together.
However, the clock uclass API does not require any such "parent"
parameter, so the clock driver must determine this information itself.
This patch implements new Tegra- specific clock API
clock_get_periph_parent() for this purpose.
The new API is implemented in the core Tegra clock code rather than SoC-
specific clock code. The implementation uses various SoC-/clock-specific
data. That data is only available in SoC-specific clock code.
Consequently, two new internal APIs are added that enable the core clock
code to retrieve this information from the SoC-specific clock code. Due to
the structure of the Tegra clock code, this leads to some unfortunate code
duplication. However, this situation predates this patch.
Ideally, future work will de-duplicate the Tegra clock code, and migrate
it into drivers/clk/tegra. However, such refactoring is kept separate from
this series.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Currently, Tegra peripheral drivers control two aspects of their HW module
clock(s):
1) The clock enable/rate for the peripheral clock itself.
2) The system-level clock tree setup, i.e. the clock parent.
Aspect 1 is reasonable, but aspect 2 is a system-level decision, not
something that an individual peripheral driver should in general know
about or influence. Such system-level knowledge ties the driver to a
specific SoC implementation, even when they use generic APIs for clock
manipulation, since they must have SoC-specific knowledge such as parent
clock IDs. Limited exceptions exist, such as where peripheral HW is
expected to dynamically switch between clock sources at run-time, such
as CPU clock scaling or display clock conflict management in a multi-head
scenario.
This patch enhances the Tegra core code to perform system-level clock
tree setup, in a similar fashion to the Linux kernel Tegra clock driver.
This will allow future patches to simplify peripheral drivers by removing
the clock parent setup logic.
This change is required prior to converting peripheral drivers to use the
standard clock APIs, since:
1) The clock uclass doesn't currently support a set_parent() operation.
Adding one is possible, but not necessary at the moment.
2) The clock APIs retrieve all clock IDs from device tree, and the DT
bindings for almost all peripherals only includes information about the
relevant peripheral clocks, and not any potential parent clocks.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Convert the Tegra MMC driver to DM_MMC. Support for non-DM is removed
to avoid ifdefs in the code. DM_MMC is now enabled for all Tegra builds.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
(swarren, fixed some NULL pointer dereferences, removed extraneous
changes, rebased on various other changes, removed non-DM support etc.)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
struct mmc_host is a Tegra-specific structure, but the name implies it's
something defined by core MMC code, which is confusing. Rename it to
struct tegra_mmc_priv to make its purpose more obvious. The new name is
also more appropriate for a DM driver private data structure, which will
be relevant later in this series.
Nothing needs access to this type except the MMC driver itself. Move the
definition into the driver C file.
Make sure all Tegra MMC functions are named tegra_mmc_*. Even though
they're all static, it's useful to have good naming so that symbol tables
are easy to interpret. A few functions aren't renamed by this patch since
they'll be deleted by a subsequent patch in this series.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
pad_init_mmc() is performing an SoC-specific operation, using registers
within the MMC controller. There's no reason to implement this code
outside the MMC driver, so move it inside the driver.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Instead of using CONFIG_* name space, rename these two macros to
SYS_FSL_* space.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move this config to Kconfig option and clean up existing uses.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Calvin Johnson <calvin.johnson@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move this option to Kconfig and clean up existing uses.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
CC: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Unlike Linux, nothing about errno.h is arch-specific in U-Boot.
As you see, all of arch/${ARCH}/include/asm/errno.h is just a
wrapper of <asm-generic/errno.h>. Actually, U-Boot does not
export headers to user-space, so we just have to care about the
consistency in the U-Boot tree.
Now all of include directives for <asm/errno.h> are gone.
Deprecate <asm/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
driver/usb/dwc3/gadget.c need a "sys_proto.h" header file, add a
empty one to make compile success.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a condition to determine the rk3288_sdram_channel size.
This patch fixes read sdram_channel property failed from DT on rk3288
boards, which not enable OF_PLATDATA.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
pmugrf is a module like grf which contain some of the iomux registers
and other registers.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Mode pins can be used as output for reset. Xilinx boards are using
this feature as additional way how to reset USB phys and also others
chips on the boards.
Mode1 is used on all these boards for this feature.
Let SPL toggle reset on this pin by default.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP provides an option to overwrite bootmode setting which
can change SPL behavior.
For example: boot SPL via JTAG and then SPL loads images from SD.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Linux kernel musb driver expects VBUS to be off while initializing
musb. Having it on results in a repeating string of warnings, followed
by an unusable peripheral. The peripheral is only usable after
physically removing the OTG adapter, letting musb reset its state.
This partially reverts commit c9f8947e66 ("sunxi: usb-phy: Never
power off the usb ports")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
A few boards define this in a header file which is incorrect. It means that
Kconfig options that rely on this cannot be used. Move it.
Signed-off-by: Simon Glass <sjg@chromium.org>
A few boards define this in a header file which is incorrect. It means that
Kconfig options that rely on this cannot be used. Move it.
Note that quite a few boards defined this options but do not appear to
actually use SPL:
BSC9132QDS_NOR_DDRCLK100_SECURE
BSC9132QDS_NOR_DDRCLK133_SECURE
BSC9132QDS_SDCARD_DDRCLK100_SECURE
BSC9132QDS_SDCARD_DDRCLK133_SECURE
BSC9132QDS_SPIFLASH_DDRCLK100_SECURE
BSC9132QDS_SPIFLASH_DDRCLK133_SECURE
C29XPCIE_NOR_SECBOOT
P1010RDB-PA_36BIT_NAND_SECBOOT
P1010RDB-PA_36BIT_SPIFLASH_SECBOOT
P1010RDB-PA_NAND_SECBOOT
P1010RDB-PA_NOR_SECBOOT
P1010RDB-PB_36BIT_NOR_SECBOOT
P1010RDB-PB_36BIT_SPIFLASH_SECBOOT
P1010RDB-PB_NAND_SECBOOT
P1010RDB-PB_NOR_SECBOOT
P3041DS_SECURE_BOOT
P4080DS_SECURE_BOOT
P5020DS_NAND_SECURE_BOOT
P5040DS_SECURE_BOOT
T1023RDB_SECURE_BOOT
T1024QDS_DDR4_SECURE_BOOT
T1024QDS_SECURE_BOOT
T1024RDB_SECURE_BOOT
T1040RDB_SECURE_BOOT
T1042D4RDB_SECURE_BOOT
T1042RDB_SECURE_BOOT
T2080QDS_SECURE_BOOT
T2080RDB_SECURE_BOOT
T4160QDS_SECURE_BOOT
T4240QDS_SECURE_BOOT
ls1021aqds_nor_SECURE_BOOT
ls1021atwr_nor_SECURE_BOOT
ls1043ardb_SECURE_BOOT
For these boards CONFIG_SPL_DM will no-longer be defined in SPL. But since
they apparently don't have an SPL, this should not matter.
Signed-off-by: Simon Glass <sjg@chromium.org>
The secure boot header files incorrectly define SPL options only if
CONFIG_SPL_BUILD is defined. This means that the options are only enabled
in an SPL build, and not with a normal 'make xxx_defconfig'. This means
that moveconfig.py cannot work, since it sees the options as disabled even
when they may be manually enabled in an SPL build.
Fix this by changing the order.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable ERRATUM_A008511, ERRATUM_A009801, ERRATUM_A009803,
ERRATUM_A009942, ERRATUM_A010165
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The CONFIG_STANDALONE_LOAD_ADDR is set to 0x80300000 by default.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This general MMDC driver adds basic support for Freescale MMDC
(Multi Mode DDR Controller). Currently MMDC is integrated on ARMv8
LS1012A SoC for DDR3L, there will be a update to this driver to
support more flexible configuration if new features (DDR4, multiple
controllers/chip selections, etc) are implimented in future.
Meantime, reuse common MMDC driver for LS1012ARDB/LS1012AQDS/
LS1012AFRDM.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds definitions of all the regesters necessary for
system sleep.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The v7_flush_dcache_all function will be called by ls102xa platform system
suspend, it is necessary to make it a public call instead of a local one, but
changing the LENTRY to ENTRY isn't enough, because there is another one using
the same name, so this one gets a psci_ prefix.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As the access to serders protocol unselected PCIe controller will
hang. So disable the R/W permission to unselected PCIe controller
including its CCSR, IO space and memory space according to the
serders protocol field of RCW.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Up to now, the function is_serdes_configed() doesn't check if the map
of serdes protocol is initialized before accessing it. The function
is_serdes_configed() will get wrong result when it was called before
the serdes protocol maps initialized. As the first element of the map
isn't used for any device, so use it as the flag to indicate if the
map has been initialized.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As part of Secure Boot Chain of trust, PPA image must be validated
before the image is started.
The code for the same has been added.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
On all TI platforms the ROM defines a "downloaded image" area at or near
the start of SRAM which is followed by a reserved area. As it is at
best bad form and at worst possibly harmful in corner cases to write in
this reserved area, we stop doing that by adding in the define
NON_SECURE_SRAM_IMG_END to say where the end of the downloaded image
area is and make SRAM_SCRATCH_SPACE_ADDR be one kilobyte before this.
At current we define the end of scratch space at 0x228 bytes past the
start of scratch space this this gives us a lot of room to grow. As
these scratch uses are non-optional today, all targets are modified to
respect this boundary.
Tested on OMAP4 Pandaboard, OMAP3 Beagle xM
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Paul Kocialkowski <contact@paulk.fr>
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Thomas Weber <weber@corscience.de>
Cc: Hannes Schmelzer <oe5hpm@oevsv.at>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Cc: Ben Whitten <ben.whitten@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: "B, Ravi" <ravibabu@ti.com>
Cc: "Matwey V. Kornilov" <matwey.kornilov@gmail.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Ash Charles <ashcharles@gmail.com>
Cc: "Kipisz, Steven" <s-kipisz2@ti.com>
Cc: Daniel Allred <d-allred@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Remove the device definition from board file, update the driver with
the new compatible property and update config with necessary options.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently MX6 SPL DDR initialization hardcodes the REF_SEL and
REFR fields of the MDREF register as 1 and 7, respectively for
DDR3 and 0 and 3 for LPDDR2.
Looking at the MDREF initialization done via DCD we see that
boards do need to initialize these fields differently:
$ git grep 0x021b0020 board/
board/bachmann/ot1200/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800
board/ccv/xpress/imximage.cfg:DATA 4 0x021b0020 0x00000800 /* MMDC0_MDREF */
board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x7800
board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/mx6qp.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6sabresd/mx6dlsabresd.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6sabresd/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6slevk/imximage.cfg:DATA 4 0x021b0020 0x00001800
board/freescale/mx6sxsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00000800
board/freescale/mx6sxsabresd/imximage.cfg:DATA 4 0x021b0020 0x00000800
board/warp/imximage.cfg:DATA 4 0x021b0020 0x00001800
So introduce a mechanism for users to be able to configure
REFSEL and REFR fields as needed.
Keep all the mx6 SPL users in their current REF_SEL and REFR values,
so no functional changes for the existing users.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
This series moves the CONFIG_SYS_CACHELINE_SIZE. First, in nearly all
cases we are mirroring the values used by the Linux Kernel here. Also,
so long as (and in this case, it is true) we implement flushes in hunks
that are no larger than the smallest implementation (and given that we
mirror the Linux Kernel, again we are fine) it is OK to align higher.
The biggest changes here are that we always use 64 bytes for CPU_V7 even
if for example the underlying core is only 32 bytes (this mirrors
Linux). Second, we say ARM64 uses 64 bytes not 128 (as found in the
Linux Kernel) as we do not need multi-platform support (to this degree)
and only the Cavium ThunderX 88xx series has a use for such large
alignment.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Stefan Roese <sr@denx.de>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Cc: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Paul Kocialkowski <contact@paulk.fr>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: "Pali Rohár" <pali.rohar@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: David Feng <fenghua@phytium.com.cn>
Cc: Alison Wang <b18965@freescale.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: York Sun <york.sun@nxp.com>
Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Aneesh Bansal <aneesh.bansal@freescale.com>
Cc: Saksham Jain <saksham.jain@nxp.com>
Cc: Qianyu Gong <qianyu.gong@nxp.com>
Cc: Wang Dongsheng <dongsheng.wang@nxp.com>
Cc: Alex Porosanu <alexandru.porosanu@freescale.com>
Cc: Hongbo Zhang <hongbo.zhang@nxp.com>
Cc: tang yuantian <Yuantian.Tang@freescale.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Josh Wu <josh.wu@atmel.com>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Hannes Schmelzer <oe5hpm@oevsv.at>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Christophe Ricard <christophe-h.ricard@st.com>
Cc: Anand Moon <linux.amoon@gmail.com>
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Carlo Caione <carlo@endlessm.com>
Cc: huang lin <hl@rock-chips.com>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Cc: Xu Ziyuan <xzy.xu@rock-chips.com>
Cc: "jk.kernel@gmail.com" <jk.kernel@gmail.com>
Cc: "Ariel D'Alessandro" <ariel@vanguardiasur.com.ar>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Bernhard Nortmann <bernhard.nortmann@web.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Ben Whitten <ben.whitten@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: "Andrew F. Davis" <afd@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Carlos Hernandez <ceh@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Ash Charles <ashcharles@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Daniel Allred <d-allred@ti.com>
Cc: Gong Qianyu <Qianyu.Gong@freescale.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Chin Liang See <clsee@altera.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Paul Kocialkowski <contact@paulk.fr>
The H3 PLL5 used for DRAM barely manages to lock to the required
frequency before DRAM controller starts, sometimes leading to wrong
delay-line calibration results.
This patch changes the PLL tuning parameters to the same values as
boot0 used, which speeds up the locking and fixes the problem.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
When the backlight's pwm input is connected to a pwm output of the SoC,
actually use pwm to drive the backlight.
The mean reason for doing this is to fix the backlight turning off
for aprox. 1 second while the kernel is booting. This is caused by
the kernel actually using pwm to drive the backlight, so that it
can dim the backlight. First the pwm driver loads and switches the
pinmux for the pin driving the backlight's pwm input to the pwm
controller. Then about 1s later the actual backlight driver loads
and tells the pwm driver to actually update the pwm settings, which
have a power-on-reset value of "off".
An additional advantage is that this allows us to initatiate the
backlight at 80%, which is the kernel default, avoiding a brightness
change while the kernel loads.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed by: Peter Korsgaard <peter@korsgaard.com>
Tegra186 supports the new standard clock and reset APIs. Older Tegra SoCs
still use custom APIs. Enhance the Tegra MMC driver so that it can operate
with either set of APIs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Tegra BPMP (Boot and Power Management Processor) is a separate
auxiliary CPU embedded into Tegra to perform power management work, and
controls related features such as clocks, resets, power domains, PMIC I2C
bus, etc. This driver provides the core low-level communication path by
which feature-specific drivers (such as clock) can make requests to the
BPMP. This driver is similar to an MFD driver in the Linux kernel. It is
unconditionally selected by CONFIG_TEGRA186 since virtually any Tegra186
build of U-Boot will need the feature.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We need to ensure that CONFIG_PHYS_64BIT is configured via Kconfig so
that it is always available to the build system. Otherwise we can run
into cases where we have inconsistent sizes of certain attributes.
Ravi Babu reported offset mismatch of struct dwc3 across files since
commit 95ebc253e6 ("types.h: move and redefine resource_size_t").
Since the commit, resource_addr_t points to phys_addr_t, whose size
is dependent on CONFIG_PHYS_64BIT for ARM architecture.
I tried my best to use "select" where possible (for example, ARMv8
architecture) because I think this kind of option is generally user-
unconfigurable. However, I see some of PowerPC boards have 36BIT
defconfigs as well as 32BIT ones. I moved CONFIG_PHYS_64BIT to the
defconfigs for such boards.
CONFIG_36BIT is no longer referenced, so all of the defines were
removed from CONFIG_SYS_EXTRA_OPTIONS.
Fixes: 95ebc253e6 ("types.h: move and redefine resource_size_t")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Ravi Babu <ravibabu@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As part of testing booting Linux kernels on Rockchip devices, it was
discovered by Ziyuan Xu and Sandy Patterson that we had multiple and for
some cases incomplete isb definitions. This was causing a failure to
boot of the Linux kernel.
In order to solve this problem as well as cover any corner cases that we
may also have had a number of changes are made in order to consolidate
things. First, <asm/barriers.h> now becomes the source of isb/dsb/dmb
definitions. This however introduces another complexity. Due to
needing to build SPL for 32bit tegra with -march=armv4 we need to borrow
the __LINUX_ARM_ARCH__ logic from the Linux Kernel in a more complete
form. Move this from arch/arm/lib/Makefile to arch/arm/Makefile and add
a comment about it. Now that we can always know what the target CPU is
capable off we can get always do the correct thing for the barrier. The
final part of this is that need to be consistent everywhere and call
isb()/dsb()/dmb() and NOT call ISB/DSB/DMB in some cases and the
function names in others.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Sandy Patterson <apatterson@sightlogix.com>
Reported-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reported-by: Sandy Patterson <apatterson@sightlogix.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Appended the compatible strings of old version PSCI to the latest
version supported. And there are some psci functions' property must
be added to DT only for psci version 0.1, including cpu_on, cpu_off,
cpu_suspend, migrate.
Note, ARMv8 Secure Firmware Framework doesn't support PSCI ver 0.1.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1021 offers two secure OCRAM blocks for trustzone.
This patch moves all the secure text sections into the OCRAM.
Signed-off-by: Wang Dongsheng <dongsheng.wang@nxp.com>
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch implements PSCI functions for ls102xa SoC following PSCI v1.0,
they are as the list:
psci_version,
psci_features,
psci_cpu_suspend,
psci_affinity_info,
psci_system_reset,
psci_system_off.
Tested on LS1021aQDS, LS1021aTWR.
Signed-off-by: Wang Dongsheng <dongsheng.wang@nxp.com>
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The input parameter CPU ID needs to be validated before furher oprations such
as CPU_ON, this patch introduces the function to do this.
Signed-off-by: Wang Dongsheng <dongsheng.wang@nxp.com>
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds all the PSCI v1.0 functions in to the common framework, with
all the functions returning "not implemented" by default, as a common framework
all the dummy functions are added here, it is up to every platform developer to
decide which version of PSCI and which functions to implement.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The LS1046A processor is built on the QorIQ LS series architecture
combining four ARM A72 processor cores with DPAA 1.0 support.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Mihai Bantea <mihai.bantea@freescale.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
New SoC LS1046A belongs to Freescale Chassis Generation 2 and
has two SerDes so we need to add this support in fsl_lsch2.
The SoC related SerDes 2 support will be added in SoC patch.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Both LS1012A and LS1043A belong to FSL_LSCH2 and share some common
configurations. So put the common define under FSL_LSCH2 to increase
readability.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support to detect Cortex-A72 core for printing it out.
The Initiator Version of A72 core should be 0x4.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for reading bootscript and bootscript header from SD. Also
renamed macros *_FLASH to *_DEVICE to represent SD alongwith NAND and
NOR flash.
Reviewed-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Override jump_to_image_no_args function to include validation of
u-boot image using spl_validate_uboot before jumping to u-boot image.
Also define macros in SPL framework to enable crypto operations.
Reviewed-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove Soc specific defines and use generic chasis specific defines
for USB controller base address mapping.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The register offset of i2c_sysc offset is not correct as per
omap5[1]/dra7[2] TRM, correct the offsets as per the
documentation.
[1] - http://www.ti.com/lit/pdf/swpu249
[2] - http://www.ti.com/lit/pdf/spruhz6
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The register offset of i2c_sysc offset is not correct as per
omap4 TRM [1], correct the offsets as per the documentation.
[1] - http://www.ti.com/lit/ug/swpu235ab/swpu235ab.pdf
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On Rockchip SoCs we typically have a main clock device that uses the Soc
clock driver. There is also a fixed clock for the oscillator. Add a function
to obtain the core clock.
Signed-off-by: Simon Glass <sjg@chromium.org>
The function is very specific to the rk3288 in its arguments
referencing the rk3288 cru and grf and every other rockchip soc
has differing cru and grf registers. So make that function naming
explicit.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
We need some macros to manipulate the NAND controller clock.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>