LX2160AQDS is a development board that supports LX2160A
family SoCs. This patch add base support for this board.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[PK: Sqaush patch for "secure boot defconfig" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Adds esbc validate command for verification of MC and DPC
firmware, along with secure boot defconfig.
Also enable distro boot.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Peng Ma <peng.ma@nxp.com>
[PK: squash "enable DM support for SATA patch" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-----BEGIN PGP SIGNATURE-----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=BbQI
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-04-rc2' of https://github.com/xypron2/u-boot
The patches fix multiple errors. Mentionable are:
- EFI unit tests (bootefi selftest) can run on i386.
- `make tests` executes the Unicode unit tests.
The LoadImage patch is preparing for further rework to be delivered
in v2019.07.
Poll for iDMAC TX/RX interrupt before disable DMA.
This to prevent disable DMA before data is transfer
completed.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Older kernel versions or systems which do not connect eMMC reset line
properly may not be able to handle situations where either the eMMC
is left in HS200/HS400 mode or SD card in UHS modes by the bootloader
and may misbehave. Downgrade the eMMC to HS/HS52 mode and/or SD card
to non-UHS mode before booting the kernel to allow such older kernels
to work with modern U-Boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Remove the duplicate code in efi_do_enter() and use efi_start_image() to
start the image invoked by the bootefi command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Up to now efi_load_pe() returns the entry point or NULL in case of an
error. This does not allow to return correct error codes from LoadImage().
Let efi_load_pe() return a status code and fill in the entry point in the
corresponding field of the image object.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If we want to properly unload images in Exit() the memory should always be
allocated in the same way. As we allocate memory when reading from file we
should do the same when the original image is in memory.
A further patch will be needed to free the memory when Exit() is called.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
All options have been moved to Kconfig and there is no need to have
board header files. Mini configurations require them that's why they are
still there.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
SPD autodetection hasn't been enabled that's why there is zero size
difference if that options are enabled/disabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Replace SDHCI controller listing by Kconfig symbol to let SPL know that
this board is using multiple SDHCIs controllers.
Kconfig help message should explain why this is needed.
Origin symbols were used in full u-boot but with moving to distro boot
this was fixed already.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CONFIG_PCA953X is not needed because of PCA953X is integrated in gpio
subsystem already. That's why also remove CMD_PCA953X which is only for
this driver.
zcu102/zcu104-revC/zcu106/zcu111 contain links to eeprom which stores MAC address.
DM_I2C is not enabled for the whole SoC because it increase size for
mini configurations and there is no I2C symbol present to setup
dependencies.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
All these board have also eeprom enabled that's why it is also enabled
via defconfig.
There is also no need to have zc70x specific config file that's why also
remove it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Boards have only one controller enabled that's why move to DM_I2C is
easy.
Add also i2c alias for not to be shown as i2c bus -1 because alias
doesn't exist.
Config file points to MAC stored in eeprom but it is not listed that's
why I have added 24c08 part.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This patch adds new mini target for versal.
This configuration is very minimal in size which runs
from OCM. It contains support for mtest which can be
used for running DDR memory tests.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds distro boot commands for qspi, ospi and mmc.
The distro boot commands now reads the script from flash offset
of 63.5MB for qspi and ospi and executes it. For mmc its same
as generic distro boot command. As either one of the qspi or ospi can
exist on hardware, defined a single distroboot command as xspi
that works for both.
Setup default location via script_offset_f to 63.5MB to match the most
xilinx reference boards for qspi, ospi for now.
512kB allocated space for script size (script_size_f) should be more
than enough to cover custom boot logic.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds distro boot commands for qspi, nand and nor.
The distro boot commands now reads the script from flash offset
of 15.75MB and executes it.
Setup default location via script_offset_f to 15.75MB to match the most
xilinx reference boards for qspi, nand and set the same using
script_offset_nor to 0xE2EC0000 for nor.
256kB allocated space for script size (script_size_f) should be more
than enough to cover custom boot logic.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds mini eMMC configuration which has only
emmc0 and emmc1 functionalities and can run from small
amount of memory. This is required for memory constraint
devices.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynq and ZynqMP are sharing similar code and there is no reason to do
code duplication. Move zynq_board_read_rom_ethaddr() to common file for
easier conversion to DM.
Use ZynqMP version that's why also add CONFIG_ZYNQ_EEPROM_BUS to Syzygy
which is only one Zynq board which is using this feature.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds distro boot commands for qspi and nand. The
distro boot commands now reads the script from flash offset
of 63.5MB and executes it.
Setup default location via script_offset_f to 63.5MB to match the most
xilinx reference boards. 512kB allocated space for script size
(script_size_f) should be more than enough to cover custom boot logic.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is doing two things.
1. Exchanging order of boot commands. distro_bootcmd is run first
followed by Xilinx boot command.
2. Remove CONFIG_BOOTCOMMAND from configs (and follow mainline) by
creating Xilinx distribution bootcommand and wiring it as the last
bootcommand.
QSPI, NAND distribution boot command will be added later.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is a place holder for HII configuration routing protocol and
HII configuration access protocol.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Allow for handling keyboard layout package in HII database protocol.
A package can be added or deleted in HII database protocol, but
we don't set 'current' keyboard layout as there is no driver that
requests a keyboard layout.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Allow for handling GUID package in HII database protocol.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch provides enough implementation of the following protocols to
run EDKII's Shell.efi and UEFI SCT:
* EfiHiiDatabaseProtocol
* EfiHiiStringProtocol
Not implemented are:
* ExportPackageLists()
* RegisterPackageNotify()/UnregisterPackageNotify()
* SetKeyboardLayout() (i.e. *current* keyboard layout)
HII database protocol in this patch series can handle only:
* GUID package
* string package
* keyboard layout package
(The other packages, except Device path package, will be necessary
for interactive and graphical UI.)
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Remove duplicate definition o EFI_SIMPLE_FILE_SYSTEM_PROTOCOL_GUID.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
UTF-16 strings in our code should all be u16 *. Fix an inconsistency for
file names which may lead to a warning for printf("%ls", ).
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Refactor the switch from supervisor to hypervisor to a new function called
at the beginning of do_bootefi().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The SetVariable() runtime service does not change the data passed to it.
So mark the parameter as constant.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The runtime variable services never change GUIDs. So we should declare
the GUID parameters as constant.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The function, efi_init_obj_list(), can be shared in different pseudo efi
applications, like bootefi/bootmgr as well as my efishell. Moreover, it
will be utilized to extend efi initialization, for example, my "removable
disk support" patch and "capsule-on-disk support" patch in the future.
So with this patch, it will be moved to a new file, efi_setup.c, under
lib/efi_loader and exported, making no changes in functionality.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Remove lines deactivated by #if 1 #else
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We use u16* for Unicode strings and efi_uintn_t for UINTN. Correct the
signature of efi_exit() and efi_start_image().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The aim of this patch is not to have temporary variables used in
distro_bootcmd left as environment variables after run something.
See the discussion[1].
Without this patch, saveenv command also saves those variables, too.
While they are apparently safe, scsi_need_init can be harmful.
Please note that, in most cases, a variable should be converted to
hush's local variable, while "devplist" cannot because it is created
by "part" command as an environment variable.
[1] https://lists.denx.de/pipermail/u-boot/2018-December/350209.html
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Some boards support NVME drives. We should be able to use them as boot
devices.
NVME access requires running 'nvme scan'.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add u16_strcpy() and u16_strdup(). The latter function will be
used later in implementing efi HII database protocol.
Signed-off-by: Akashi Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Commit 393fccdf6c73 ("efi_loader: efi_guid_t must be 64-bit aligned")
has changed the alignment of efi_guid_t. This changed the size of
struct efi_configuration_table on 32-bit systems form 20 to 24 bytes. As
an array of this type is pointed to by the system table this breaks
compatibility with existing versions of GRUB and Linux. Let's get back the
original size by using the attribute __packed.
Fixes: 393fccdf6c73 ("efi_loader: efi_guid_t must be 64-bit aligned")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The UEFI Specification Version 2.7 Errata A defines:
"EFI_GUID
128-bit buffer containing a unique identifier value.
Unless otherwise specified, aligned on a 64-bit boundary."
Before this patch efi_guid_t was 8-bit aligned.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Common sound support
buildman environment support
of-platdata documentation improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlxf7igRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYKfggApQiL0Gv6NdGAQN+zfpjKY5a2QyjKsAxa
KLm3q8XyXIQXufMWOEPoW1iWm0iixpIFgChy8ff3m/OPDzsx99UXDTyvjitsSxtQ
5tFu8K78nUZT6OOE3HNhhlyW/xK442oKBzGt4MUt3kUZOELsCNuftgbJUWksHuO3
6pPrgt36E0uRGbUA4ioYCU336viJRPOOCdqb8hHViEihFj/IEv5T82RdE5y97YxG
dT7BZxjPkBH5ZN1uD/tdxG1k6IZBagZiYoDAsYp4YqNwmVsm5sLrZ9QVSf7EcH/y
qX8butZesiMd7xm7RROlrIImh7fb36N3zsoRiUWZDo1Al3IRkmZyVA==
=tdut
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-10feb19' of git://git.denx.de/u-boot-dm
Samsung sound patches (applied for Samsung maintainer)
Common sound support
buildman environment support
of-platdata documentation improvements
regulator_set_enable() api throws an error in the following three cases:
- when requested to disable an always-on regulator
- when set_enable() ops not provided by regulator driver
- when enabling is actually failed.(Error returned by the regulator driver)
Sometimes consumer drivers doesn't want to track the first two scenarios
and just need to worry about the case where enabling is actually failed.
But it is also a good practice to have an error value returned in the
first two cases.
So introduce an api regulator_set_enable_if_allowed() which ignores the
first two error cases and returns an error as given by regulator driver.
Consumer drivers can use this api need not worry about the first two
error conditions.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This enum still exists but we can shrink it a little based on recent
driver-model conversions with samsung. Update it to remove unused items.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
At present the model is shown twice, once in the generic code and once
in the exynos code. Drop the latter.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
This converts the following to Kconfig:
CONFIG_BOARD_TYPES
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Bootm will fail to load kernels over 8MB, this is not enough
for our 64bit kernel images. Increase this to 64MB.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This add the initial support of the broadcom reference
board bcm963158 with a bcm63158 SoC.
This board has 1 GB of ram, 512 MB of flash (nand),
2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
The board_r init function was complaining that we are looping through
an array, calling all our tiny init stubs sequentially via indirect
function calls (which can't be speculated, so they are slow).
The solution to that is pretty easy though. All we need to do is inline
the function that loops through the functions and the compiler will
automatically convert almost all indirect calls into direct inlined code.
With this patch, the overall code size drops (by 40 bytes on riscv64)
and boot time should become measurably faster for every target.
Signed-off-by: Alexander Graf <agraf@suse.de>
- Add st,digbypass on clk_hse node (needed for board rev.C)
- MLAHB/AHB max frequency increased from 200 to 209MHz, with:
- PLL3P set to 208.8MHz for MCU sub-system
- PLL3Q set to 24.57MHz for 48kHz SAI/SPI2S
- PLL3R set to 11.29MHz for 44.1kHz SAI/SPI2S
- PLL4P set to 99MHz for SDMMC and SPDIFRX
- PLL4Q set to 74.25MHz for EVAL board
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The content between these guards was removed in commit 9baa2bce28
("Removed unused references to CONFIG_SERIALx"). Remove the now
empty #ifdef/#endif block and the accompanying comment.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Memory functions may have architecture specific implementations. These
should be tested.
Provide unit tests for memset(), memcpy(), memmove().
Provide a 'ut lib' sub-command to execute the tests.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is wrapper for calling of_alias_get_highest_id() when live tree is
enabled and fdtdec_get_alias_highest_id() if not.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Find out the highest alias ID used for certain subsystem.
This call will be used for alocating IDs for i2c buses which are not
described in DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The same functionality was added to Linux for i2c bus registration with this
commit message:
"
of: base: add function to get highest id of an alias stem
I2C supports adding adapters using either a dynamic or fixed id. The
latter is provided by aliases in the DT case. To prevent id collisions
of those two types, install this function which gives us the highest
fixed id, so we can then let the dynamically created ones come after
this highest number.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
"
Add it also to U-Boot for DM I2C support.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
not break functionality.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
SF_DUAL_FLASH claims to enable support for SF_DUAL_STACKED_FLASH and
SF_DUAL_PARALLEL_FLASH. But, in current U-Boot code, grepping for above
enums yield no user and therefore support seems to be incomplete. Remove
these configs so as to avoid confusion.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Switch spi_flash_* interfaces to call into new SPI NOR framework via MTD
layer. Fix up sf_dataflash to work in legacy way. And update sandbox to
use new interfaces/definitions
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
For legacy reasons, we will have to keep around U-Boot specific
SPI_FLASH_BAR and SPI_TX_BYTE. Add them back to the new framework
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Current U-Boot SPI NOR support (sf layer) is quite outdated as it does not
support 4 byte addressing opcodes, SFDP table parsing and different types of
quad mode enable sequences. Many newer flashes no longer support BANK
registers used by sf layer to a access >16MB of flash address space.
So, sync SPI NOR framework from Linux v4.19 that supports all the
above features. Start with basic sync up that brings in basic framework
subsequent commits will bring in more features.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
In arch/sandbox/include/asm/types.h we have
Therefore for 32 bit Sandbox build BITS_PER_LONG turns out to be 32 as
CONFIG_PHYS64 is not set
This messes up the current logic of GENMASK macro due to mismatch b/w
size of unsigned long (64 bit) and that of BITS_PER_LONG.
Fix this by using CONFIG_SANDBOX_BITS_PER_LONG which is set to 64/32
based on the host machine on which its being compiled.
Without this patch:
GENMASK(14,0) => 0x7fffffffffff
After this patch:
GENMASK(14,0) => 0x7fff
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Completely move CONFIG_SPI_FLASH from remaining board header files to
defconfigs
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
With the new DM_VIDEO support in the Armada XP LCD driver, this patch
adds the needed DT node for the LCD controller to the theadorable dts
file. This DT property is not added to the Armada XP dtsi files, as this
LCD feature is pretty unusual for this SoC and I personally know of no
other board that uses this controller.
This patch also enables CONFIG_BMP_16BPP/24BPP/32BPP, as the "old" bmp
command supported these BMP files.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
This patch adds DM_PCI support to the MVEBU PCIe driver. This is
necessary, since all PCI drivers have to be moved to DM (driver model)
until the v2019.07 release.
To not break git bisect'ablility, this patch also moves CONFIG_PCI_MVEBU
from config headers to the defconfig files.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: VlaoMao <vlaomao@gmail.com>
This function will be used by the Marvell Armada XP/38x PCIe driver,
which is moved to DM right now. So let's extract the functionality
from pci_uclass_child_post_bind() to make it available.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* support for Chromebook Bob
* full pinctrl driver using DTS properties
* documentation improvements
* I2S support for some Rockchip SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcVG0IAAoJECaAFcEOcohNKVAIAJd3DN/qudcVQdkuvAGK6WIk
Umxkm6rxHwur7oU+wxvK1p1l/0YTFBeCfo15quH1DkSc/WIUnmBlLmDvqpGVmPmh
ydZNE9ZChn0OKRIaM6pKJr+3p155cQDe6Mgg2j/5CnNx28KxT+vu7EqZbZvbQPag
wcZEK6Z6E5jMVHVn2lbLgmsBPmY7ksX168IqpvzTxIj0a4J3n0DcJUnO4RBBS0Q2
PGEvFhTvigVWs6r6GL0gLn3VwnQX30xQlIuKKORPcdhjk97cJcS4+bRxdTENTKD9
j3+pgyl1n04O8sPONZS7pH3fvJwtC6SwnoxTYxGrvjedw1LxbyHG3cqcGDg/TJ8=
=ik3X
-----END PGP SIGNATURE-----
Merge tag 'for-master-20190201' of git://git.denx.de/u-boot-rockchip
u-boot-rockchip changes for 2019.04-rc1:
* support for Chromebook Bob
* full pinctrl driver using DTS properties
* documentation improvements
* I2S support for some Rockchip SoCs
This fixes the automatic lmb initialization and reservation for boards
with more than one DRAM bank.
This fixes the CVE-2018-18439 and -18440 fixes that only allowed to load
files into the firs DRAM bank from fs and via tftp.
Found-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Bob is a 10-inch chromebook produced by Asus. It has two USB 3.0 type-C
ports, 4GB of SDRAM, WiFi and a 1280x800 display. It uses its USB ports
for both power and external display. It includes a Chrome OS EC
(Cortex-M3) to provide access to the keyboard and battery functions.
Support so far includes only:
- UART
- SDRAM
- MMC, SD card
- Cros EC (but not keyboard)
Not included:
- Keyboard
- Display
- Sound
- USB
- TPM
Bob is quite similar to Kevin, the Samsung Chromebook Plus, but support
for this is not provided in this series.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Some boards use different stdio environment variables from the default.
Provide a #define for this which can be set before including the header
file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
In space-constrained environments or before driver model is available, it
is sometimes necessary to set GPIO values. Add an SPL API for this, to
allow early board code to change GPIOs. The caller must provide the
register address, so that the drivers can be fairly generic.
This API can be implemented by GPIO drivers, behind a suitable guard,
like #ifdef CONFIG_SPL_BUILD.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPLY_FS_EXT4 so both
obj-$(CONFIG_$(SPL_)FS_EXT4) and CONFIG_IS_ENABLED(FS_EXT4) can be
used to control the build in both SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT so
obj-$(CONFIG_$(SPL_)FS_FAT) can be used to control the build in both
SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Testing has shown that the timer on the MT7688 platforms does not run
correctly (too fast timeout). This patch changes
CONFIG_SYS_MIPS_TIMER_FREQ from 200MHz to 290MHz which is the correct
value, as its also used in Linux.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Allows displaying the console via video and using a USB keyboard.
Also enables CONFIG_SPLASH_SCREEN if using video.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Some IPs like the meson VPU can only feed a particular pixel format to
dw_hdmi. As of now, the driver is hardcoded to use RGB888 as input.
This commit enables different pixel format inputs, with the appropriate
CSC configuration.
Signed-off-by: Jorge Ramire-Ortiz <jramirez@baylibre.com>
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Some IPs like the meson VPU have a specific way to write to dw_hdmi
registers. Make it configurable.
Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
[added commit description]
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This unbreaks dfu mmc_file_op which is currently broken since using the
load cmd on a buffer from heap is not allowed - added with
commit aa3c609e2b ("fs: prevent overwriting reserved memory")
Fixes: commit aa3c609e2b ("fs: prevent overwriting reserved memory")
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
This patch converts the warp7 and warp7_bl33 board ports over to using the
DM PMIC model.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable SPL for i.MX8QXP MEK, and currently use SPL FIT.
The SPL enable SPL_DM to use MMC/PINCTRL/POWER DOMAIN/CLK.
Note: SPL FIT could not support secure boot chain, because i.MX8/8X
only support i.MX container format. This container format has
not been upstreamed, so we use FIT for now. When SPL container
supported, we could switch to that.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix mixed up boot commands between raw NAND and eMMC variant. Also
make sure that the boot_file is defined for the eMMC boot command.
Fixes: a62c60610f ("colibri_imx7_emmc: add Colibri iMX7D 1GB (eMMC) module support")
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The original definition added the string mtdparts= to the Linux Kernel
args twice: mtdparts=mtdparts=. Fix that.
Signed-off-by: Olaf Mandel <o.mandel@menlosystems.com>
Reviewed-by: Marek Vasut <marex@denx.de>
After merging the boot partition into the root partition, the splashfile
resides in the /boot subdirectory: update the default environment to
reflect that.
Signed-off-by: Olaf Mandel <o.mandel@menlosystems.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add support for the VXT VL050-8048NT-C01 panel connected through
the 24 bit parallel LCDIF interface.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Port for the PHYTEC phyBOARD-i.MX6UL-Segin single board computer. Based on
the PHYTEC phyCORE-i.MX6UL SOM (PCL063).
CPU: Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 44C
Reset cause: POR
Board: PHYTEC phyCORE-i.MX6UL
I2C: ready
DRAM: 256 MiB
NAND: 512 MiB
MMC: FSL_SDHC: 0
In: serial
Out: serial
Err: serial
Net: FEC0
Working:
- Eth0
- i2C
- MMC/SD
- NAND
- UART (1 & 5)
- USB (host & otg)
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Rather than checking for CONFIG_TPL_BUILD and then re-defining
CONFIG_SPL_TEXT_BASE make use of CONFIG_TPL_TEXT_BASE directly.
Cc: York Sun <york.sun@nxp.com>
Cc: Po Liu <po.liu@nxp.com>
Cc: Qiang Zhao <qiang.zhao@nxp.com>
Cc: Timur Tabi <timur@tabi.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
As a follow-up, change the name of the newly introduced function
'lmb_get_unreserved_size' to 'lmb_get_free_size', which is more
appropriate.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Fix test/lib/lmb.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch has been tested on the mcf54415-based stmark2
board. The eSDHC driver works reliably using DMA mode.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Like AM33xx and AM43xx, DRA7xx and AM57xx devices may need to
have an non-standard boot address in memory. This may be due
to the device being a high security variant, which place the
Initial SoftWare (ISW) after certificates and secure software.
Allow these devices to set this from Kconfig.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Do this by using $(SPL_) in Makefiles and CONFIG_IS_ENABLED in C code.
This ensures the files and features are only built into the right build
for which they are enabled. Using the macros to simplify this patch was
made possible by the config symbol rename done in the last patch.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
The symbol CONFIG_SPL_DFU_SUPPORT in SPL build has the same
meaning as CONFIG_DFU in regular U-Boot. Drop the _SUPPORT
to allow for cleaner use in code.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
It adds missing pinctrl headers, updates clock header and sync up Poplar
device tree with kernel 4.20 release.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
A few platforms recently added in CONFIG_DFU_MMC under include/configs
rather than via the defconfig, update them.
Signed-off-by: Tom Rini <trini@konsulko.com>
A couple of trivial fixes and improvements for ARC
Most notable are:
* Move of ENV_SIZE/ENV_OFFSET to Kconfig
* Fix with private structure allocation for arc_uart
* Definition of CONFIG_SYS_CACHELINE_SIZE useful for building drivers
Join the party of some ARM boards and drop more
items from include/configs/xxx.h.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
CONFIG_DW_SERIAL is no longer used anywhere so let's forget about it.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: "Jorg Krause" <joerg.krause@embedded.rocks>
Cc: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
No mainline board enables CONFIG_MCAST_TFTP and there have been
compilation issues with the code for some time. Additionally, it has a
potential buffer underrun issue (reported as a side note in
CVE-2018-18439).
Remove the multicast TFTP code but keep the driver API for the future
addition of IPv6.
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
ether_crc was added to the core net code in commit 53a5c424bf
("multicast tftp: RFC2090") so that other drivers could use it. However
the only current user of it is tsec.c so move it there.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
With CONFIG_REGEX enabled, ETHADDR_WILDCARD is set up for up to 10
interfaces (0..9) as the number can only have one digit.
On boards with more than 10 interfaces, this leads to the protection
and format checks being absent for eth10addr and above.
Fix this by changing ETHADDR_WILDCARD from "\\d?" to "\\d*" to allow
more than one digit.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
ETHADDR_WILDCARD is defined as the same value in both env_flags.h
and env_callback.h
As env_callback.h includes env_flags.h, remove the duplicate definition
from env_callback.h
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The phy devices can be accessed via clause 22 or via clause 45.
This information can be deduced when we read phy id. if the phy id
is read without giving any MDIO Manageable Device Address (MMD), then
it conforms to clause 22. otherwise it conforms to clause 45.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There is no i2c connected in base DT that's why disable I2C commands.
Also remove zynq_zybo which is not needed now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch enables CONFIG_REMAKE_ELF for Zynq platform
so that it generates u-boot.elf from binary which works
for all Zynq boards with OF_SEPARATE option enabled.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As Ocelot, Servalt, Luton and Jaguar2, this family of SoCs are
found in Microsemi Switches solution.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
- Sync Armada-38x dts with Linux 4.20 from Chris
- Misc changes and enhancements to Turris Mox (v4) from Marek
- Reserve PSCI area for Armada 8k from Heinrich
- New Allied Telesis x530 board (Armada-385) from Chris
- Misc minor changes (defconfig etc)
This is a range of stackable network switches. The SoC is Armada-385 and
there are a number of variants with differing network port
configurations. The DP variants are intended for a harsher operating
environment so they use a different i2c mux and fit industrial-temp
parts.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This is needed for some scenarios, such as booting large FIT image.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The bounce buffer is used by a few drivers (most of the MMC drivers)
to overcome limitations in their respective DMA implementation.
This moves the configuration to Kconfig and makes it user-selectable
(even though it will be a required feature to make those drivers
work): the expected usage is for drivers depending on this to 'select'
it unconditionally from their respective Kconfig (see follow-up
patches).
This commit includes a full migration using moveconfig.py to ensure
that each commit compiles. To ensure bisectability we update
dependencies of various drivers to now select BOUNCE_BUFFER when needed.
[trini: Squash all patches to ensure bisectability]
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br> [dw_mmc portion]
Reviewed-by: Fabio Estevam <festevam@gmail.com> [mxsmmc portion]
Reviewed-by: Simon Glass <sjg@chromium.org> [tegra portion]
Onc of key blocker for using USB Generic host controller
drivers in Allwinner are CLK and RESET drivers, now these
available for USB usage.
So switch sunxi USB use EHCI and OHCI Generic controllers.
Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD
where it already have USB_EHCI_HCD
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add reset_valid to check whether given reset is valid
or not.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Update sun50i-a64-ccu.h from the Linux sunxi/dt64-for-4.20 tree:
commit 679294497be31596e1c9c61507746d72b6b05f26
Author: Rodrigo Exterckötter Tjäder <rodrigo@tjader.xyz>
Date: Wed Sep 26 19:48:24 2018 +0000
arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay
This should be a part of previous sync patch from
commit 1b39a1834e
Author: Andre Przywara <andre.przywara@arm.com>
Date: Mon Oct 29 00:56:47 2018 +0000
sunxi: A64: Update .dts/.dtsi files
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Update all A80 devicetree dtsi and dtsi files from
Linux-v4.18-rc3 with below commits.
arch/arm/boot/dts/sun9i-a80*:
commit 190e3138f9577885691540dca59c2f07540bde04
Merge: cafc87023b0d a7affb13b271
Author: Arnd Bergmann <arnd@arndb.de>
Date: Tue Mar 27 14:58:00 2018 +0200
Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
include/dt-bindings/*/sun9i-a80-*:
commit 783ab76ae553abc23f80ef7511052d055697531b
Author: Chen-Yu Tsai <wens@csie.org>
Date: Sat Jan 28 20:22:36 2017 +0800
clk: sunxi-ng: Add A80 Display Engine CCU
Note: sun9i-a80-cx-a99.dts is updated only uart0, since the same
dts is not available in Linux.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
bananapi r2 can be booted from sd-card and emmc
saving the environment have to choose the storage
from which the device has booted
also the offset is set to 1MB to make sure env is written
to block "user data area" between uboot and first partition
https://www.fw-web.de/dokuwiki/lib/exe/fetch.php?cache=&media=bpi-r2:boot-structure.png
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
fsl-mc lazyapply command applies dpl from efi_exit_boot_services().
Status of fsl-mc node in working fdt is updated at this stage.
However, an efi application like grub may already have copied the fdt.
So the updates to fdt done at efi_exit_boot_services() may not be
visible to the OS. Fix it by updating fdt earlier if fsl-mc lazyapply
command is used.
Fixes: b7b8410a8f (ls2080: Exit dpaa only right before exiting U-Boot)
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
Patch fixes build error when enabling CONFIG_ENV_IS_IN_SPI_FLAS
and CONFIG_ENV_IS_IN_MMC at the same time mentioned issue in
below link:
Refer: https://lists.denx.de/pipermail/u-boot/2018-February/319565.html
build error when enabling CONFIG_ENV_IS_IN_SPI_FLASH and
CONFIG_ENV_IS_IN_MMC at the same time.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls2088aqds_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls2088ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- remove EL3 specific erratas for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1088aqds_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- MC address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- ifc chip select changes for TFABOOT
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1088ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- MC address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- ifc chip select changes for TFABOOT
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
lmb.h includes an extern declaration of "struct lmb lmb;" which
is not used anywhere, so remove it.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This fixes CVE-2018-18440 ("insufficient boundary checks in filesystem
image load") by using lmb to check the load size of a file against
reserved memory addresses.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds two new functions, lmb_alloc_addr and
lmb_get_unreserved_size.
lmb_alloc_addr behaves like lmb_alloc, but it tries to allocate a
pre-specified address range. Unlike lmb_reserve, this address range
must be inside one of the memory ranges that has been set up with
lmb_add.
lmb_get_unreserved_size returns the number of bytes that can be
used up to the next reserved region or the end of valid ram. This
can be 0 if the address passed is reserved.
Added test for these new functions.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
As we are moving to multi-dtb and board detection, remove static board
config options, and introduce board probing instead.
Luton: This add single-binary support for the two MSCC luton-based
reference boards - pcb090 and pcb091. The SoC chip ID is used to
determine the board type.
Ocelot: This add single-binary support for the two MSCC ocelot-based
reference boards - pcb120 and pcb123. The PHY ids on specific ports
are used to determine the board type.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Buildman clang support and a few fixes
Small fixes to 'dm tree' and regmap test
Improve sandbox build compatibility
A few other minor fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlw+AlIACgkQfxc6PpAI
reYchAf+L/P5JsLoCKAY84v11eWQkCS44idAYStD8Q023dyuyNC/W6G3qEQVGkHu
SXBzNrZ5wSJanN5I3h3ktJ7yfMOYIvSO2qLHphxDstPaZbCY4Zac6NywHrHxQpA9
fbSilQRbcVWrPo5rsjjZhXmMdQRZVOmGD6CYZj1AihWAiHfYth7f6laNWNTWQA8C
z+aoiF70t/PbvwFbgdzzYOjoGdXI9XML0xTqdLWRlsBKjf3z54pCV6LmN2xrsrDZ
k7lr+x7ajJUFhivxzjowf4aOjhDB+/+I3sr+hJ5vkMM0Kqg14bbEU+xJRGpDc18K
QPvVHT5JGe/nq1cZXuCqzrYxTrrA7A==
=w9ln
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-15jan19' of git://git.denx.de/u-boot-dm
Fix recent changes to serial API for driver model
Buildman clang support and a few fixes
Small fixes to 'dm tree' and regmap test
Improve sandbox build compatibility
A few other minor fixes
Add the dollar_complete() function to auto-complete arguments starting
with a '$' and use it in the cmd_auto_complete() path such that all
args starting with a $ can be auto-completed based on the available env
vars.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
[trini: Fix some linking problems]
Signed-off-by: Tom Rini <trini@konsulko.com>
Switching private data manual allocation to driver model auto allocation
so users no longer need to deallocate themself because this would be
deallocated by driver model when the device is no longer required.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Most cmd/xxx.c source files expose several commands through a single
entry point. Some of them are doing the sub-command parsing manually in
their do_<cmd>() function, others are declaring a table of sub-commands
and then use find_cmd_tbl() to delegate the request to the sub command
handler.
In either case, the amount of code to do that is not negligible and
repetitive, not to mention that almost no commands are implementing
the auto-completion hook, which means most u-boot commands lack
auto-completion.
Provide several macros to easily define commands exposing sub-commands.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The repeatable property is currently attached to the main command and
sub-commands have no way to change the repeatable value (the
->repeatable field in sub-command entries is ignored).
Replace the ->repeatable field by an extended ->cmd() hook (called
->cmd_rep()) which takes a new int pointer to store the repeatable cap
of the command being executed.
With this trick, we can let sub-commands decide whether they are
repeatable or not.
We also patch mmc and dtimg who are testing the ->repeatable field
directly (they now use cmd_is_repeatable() instead), and fix the help
entry manually since it doesn't use the U_BOOT_CMD() macro.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some commands have a table of sub-commands. With minor adjustments,
complete_cmdv() is able to provide auto-completion for sub-commands
(it's just about passing the table of commands instead of taking the
global one).
We rename this function into complete_subcmd() and implement
complete_cmdv() as a wrapper around complete_subcmdv().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The USB support for this board was never really tested, in fact, the
presence of these options are more a copy & paste error from the
Beagleboard than a feature that really was used. As doesn't work, remove
for now. If someone at some point want to add this support he'll need to
migrate the board to use CONFIG_DM_USB instead.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
We need to define the standalone load address to use standalone
application on qemu-riscv. Define it and set it equal to
CONFIG_SYS_LOAD_ADDR.
To not overwrite it, change the assigned of CONFIG_STANDALONE_LOAD_ADDR
in arch/riscv/config.mk to a conditional one.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
The getconfig() comment is out of date. Fix this and add comments for
recently added functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
