This patch moves all the font configuration values into video_font_data.h
so they are all in the right place with the font. The video_font.h now only
includes video_font_data.h and will allow us to select and include different
font once more fonts are added.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
[agust: fixed build warning for mcc200]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
If you don't wait you will loose the first sent packet
even all bits in emacps are correctly setup.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
The first 1MB is not initialized by first stage bootloader.
Check if memory is setup to 16bit mode and ECC is enabled.
If it is, clear the first 1MB.
Also u-boot should report only the half size of memory.
Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
the clk_get() function is needed for the da8xx-fb video driver,
which is used on the am3xx based siemens boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
the da8xx-fb driver works also on am335x boards. So move
the da8xx-fb.h file from arch/arm/include/asm/arch-davinci
to drivers/video, so this driver can used from am335x
based boards. Also add WVGA panel_type.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
Fix the following build error caused by patch "powerpc/pcie: add PCIe
version 3.x support":
pcie.c:302:34: error: 'PCI_LTSSM' undeclared (first use in this function)
pcie.c:303:15: error: 'PCI_LTSSM_L0' undeclared (first use in this function)
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Add special function that executes a specially crafted circular
DMA descriptor. The function doesn't wait for the descriptor to
finish the transfer, since the descritor never finishes. This is
useful when operating a SmartLCD through the LCDIF interface, as
the LCDIF does not give us any means to have continuous refresh
of the SmartLCD. Instead, the RUN bit in the LCDIF CTRL register
must be triggered manually. This can be worked around by starting
an DMA transfer which continuously sets the RUN bit. This function
allows starting exactly such transfer.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The TIMING_CFG_3[EXT_ACTTOPRE] register field is 2 bits wide, but
the mask omitted the LSB. This patch provides a 2-bit wide mask.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
The Freescale C29x family is a high performance crypto co-processor.
It combines a single e500v2 core with necessary SEC engine. There're
three SoC types(C291, C292, C293) with the following features:
- 512K L2 Cache/SRAM and 512 KB platform SRAM
- DDR3/DDR3L 32bit DDR controller
- One PCI express (x1, x2, x4) Gen 2.0 Controller
- Trust Architecture 2.0
- SEC6.0 engine
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Po Liu <Po.Liu@freescale.com>
T4240 PCIe IP is version 3.0 and has some update comparing previous
QorIQ products.
1. Move Freescale specific register define
to
arch/powerpc/include/asm/fsl_pci.h
and update the register offset define for T4240.
2. add the status/control register define
use status/control register to judge the link status
3. The original code uses 'Programming Interface' field to judge if PCIE is
EP or RC mode, however, T4240 does not support this functionality.
According to PCIE specification, 'Header Type' offset 0x0e is used to
indicate header type, so for PCIE controller, the patch changes code to
use 'Header Type' field to identify if the PCIE is RC or EP mode.
This patch fixes the PCIe card link up issue on T4240QDS.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
1. Add CONFIG_SYS_DPAA_RMAN macro to t4240 and b4860.
2. Decrease RMan liodn offset number.
SET_RMAN_LIODN() is used to set liodn offset of RMan blocks 0-3.
For t4240 and b4860, RMan liodn base is assigned to 922, the original
offset number is too large that the liodn (base+offset 922+678 = 1600)
is greater than 0x500 the maximum liodn number.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Also change the define name SRDS_RSTCTL_SDPD to
SRDS_RSTCTL_SDEN, which stands for SerDes enable
as mentioned in SerDes module guide
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
BSC9132 SoC has two separate DDR controllers for PowerPC side and DSP side
DDR. They are mapped to PowerPC and DSP CCSR space respectively.
BSC9132QDS has two on-board MC34716EP DDR3 memory one connected to PowerPC
and other to DSP side controller.
Configure DSP DDR controller similar to PowerPC side DDR controller as
memories are exactly similar.
Signed-off-by: Manish Jaggi <manish.jaggi@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
BSC9132QDS is a Freescale Reference Design Board for BSC9132 SoC which is a
integrated device that contains two powerpc e500v2 cores and two DSP
starcores.
To support DSP starcore
-Creating LAW and TLB for DSP-CCSR space.
-Creating LAW for DSP-core subsystem M2 and M3 memory
-Creating LAW for 1GB DDR which is connected exclusively to DSP-cores
Signed-off-by: Manish Jaggi <manish.jaggi@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
When a board (slave) boots from SRIO/PCIE, it would get the instructions
from a remote board (master) by SRIO/PCIE interface, and the slave's
u-boot image should be built with the
SYS_TEXT_BASE=0xFFF80000;
So the u-boot of the slave should avoid the NOR_BOOT branch at the
booting stage.
For example, when a P2041RDB boots from SRIO/PCIE, it will set TLB
entry 15 from base address "CONFIG_SYS_MONITOR_BASE & 0xffc00000",
and with the 4M size as the boot window in NOR_BOOT branch. Because
the CONFIG_SYS_MONITOR_BASE = CONFIG_SYS_TEXT_BASE = 0xFFF80000, so
the TLB entry will be from base address 0xffc00000 and with 4M size.
Then the u-boot will set TLB entry 14 from base address
"CONFIG_SYS_INIT_RAM_ADDR", and with the 16K size as the initial
stack window. For the P2041RDB platform, the CONFIG_SYS_INIT_RAM_ADDR
= 0xffd00000. So the TLB entry 14 and 15 will be in confliction.
There will be right TLB entries configurations when avoid the
NOR_BOOT branch and set the boot window from 0xfff00000 with 1M
size space.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Erratum A-005812 Incorrect reservation clearing in Write Shadow mode can
result in invalid atomic operations. For u-boot, this erratum only impacts
SoCs running in write shadow mode.
Signed-off-by: York Sun <yorksun@freescale.com>
JEDEC spec requires the clocks to be stable before deasserting reset
signal for RDIMMs. Clocks start when any chip select is enabled and
clock control register is set. This patch also adds the interface to
toggle memory reset signal if needed by the boards.
Signed-off-by: York Sun <yorksun@freescale.com>
On selected platforms, x4 DDR devices can be supported. Using x4 devices may
lower the performance, but generally they are available for higher density.
Tested on MT36JSF2G72PZ-1G9E1 RDIMM.
Signed-off-by: York Sun <yorksun@freescale.com>
When chip select interleaving is enabled, cs0_bnds is used for address
binding. Other csn_bnds are not used. When two controllers interleaving is
enabled, cs0_bnds of both controllers are used, other csn_bnds are not.
However, the unused csn_bnds may be used internally for calculating
addresses for calibration. Setting those registers to 0 may confuse
controllers in some cases. Instead, setting them to 0xffffffff together
with normal LAWs will guarantee the address is not mapped to DDR.
Signed-off-by: York Sun <yorksun@freescale.com>
Prepare for emulator support for mpc85xx parts.
Disable DDR training and skip wrlvl_cntl_2 and wrlvl_cntl_3 registers.
These two registers improve stability but not supported by emulator.
Add CONFIG_FSL_TBCLK_EXTRA_DIV for possible adjustment to time base.
Signed-off-by: York Sun <yorksun@freescale.com>
Move CONFIG_FSL_CORENET define to config_mpc85xx.h. It is not board
specific feature and belongs to SoC header.
Signed-off-by: York Sun <yorksun@freescale.com>
For some PowerPC platforms, LIODN registers for SRIO ports are
in SRIO register address space. So the ccsr_rio structure should
be updated for those LIODN registers.
In addition, add a new macro "SET_SRIO_LIODN_BASE" to create
the SRIO LIODN ID table based on the SRIO LIODN register address.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
U-Boot does not compile for the adp-ag101 boards since
commit a8f9cd1893
(net: update FTGMAC100 for MMU/D-cache support)
The driver assumes that the DMA allocation API are provided by all
architectures. This is not the case for nds32 and it causes a
build error. This patch adds DMA allocation API to avoid the errors.
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
Cc: Macpaul Lin <macpaul@gmail.com>
Cc: Andes <uboot@andestech.com>
Signed-off-by: Andes <uboot@andestech.com>
Initialization spi.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Now that nothing uses CONFIG_ARCH_DEVICE_TREE, stop defining it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Current code uses gd->baudrate before setting its value.
Besides, I got below build warning which is introduced by
commit ddb5c5be "blackfin: add baudrate to bdinfo".
board.c:235:3: warning: passing argument 1 of 'simple_strtoul' makes pointer from integer without a cast [enabled by default]
include/vsprintf.h:27:7: note: expected 'const char *' but argument is of type 'unsigned int'
This patch ensures we get the baudrate setting before using it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
The function return from P_FUNCT2MUX(per) takes 2 bits, however
for BF537_FAMILY with offset != 1 the function is 1 bit.
Also has small refactor for better readability.
In portmux_setup(), it looks odd having "muxreg &= ~(3 << 1);"
while in current code we do muxreg |= (function << offset);.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
In special_gpio_free(), call unreserve() rather than reserve() to release gpio.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
NOR requires that s_init be within the first 4KiB of the image so that
we can perform the rest of the required pinmuxing to talk with the rest
of NOR that we are found on. When NOR_BOOT is set we save our
environment in NOR at 512KiB and a redundant copy at 768KiB. We avoid
using SPL for this case and u-boot.bin is written directly to the start
of NOR.
We enclose the DMM-related parts of arch/arm/cpu/armv7/am33xx/emif4.c
with TI81xx checks as at this time U-Boot does not discard unused
sections in the main build and this code relies on functions specific to
(and only provided in) ti81xx-related code.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds support for the NOR module that attaches
to the memory cape for a Beaglebone board. This does not
add booting support; only support so that you can boot from
SD/MMC and see the NOR module so that it can be programmed.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
[trini: Clean up config changes slightly]
Signed-off-by: Tom Rini <trini@ti.com>
Based on our usage of the GPMC, either with NOR or NAND we do not need
to be setting the irqstatus or irqenable bits and should clear them like
we have historically.
Signed-off-by: Tom Rini <trini@ti.com>
A little background is probably appropriate for this patch.
Since "the beginning" of usage of the SABRE Lite and Nitrogen6x
boards, DVI detection has been somewhat broken.
Some (most) DVI monitors don't produce the "HPD" bit in
the PHY_STAT0 register, but do show proper toggling of the
RX_SENSE0..3 bits.
Creating a new the bit-mask to include all five bits and
modifying the 'hdmidet' command and internal detection
routines allows these monitors to function properly in U-Boot.
A related patch to our kernels allows things to work under
Linux:
7d8752905c
Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Instead of duplicating HDMI setup code for every mx6 board, factor out the common code
Signed-off-by: Pardeep Kumar Singla <b45784@freescale.com>
Acked-By: Eric Nelson <eric.nelson@boundarydevices.com>
Locking DPLL_GMAC
[mugunthanvnm@ti.com:Configure only if CPSW is selected]
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
The OMAP36xx/OMAP37xx family uses L3 frequency of 200MHz instead of 165MHz
used by OMAP34xx/OMAP35xx.
Also fix checkpatch warning about alignment.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Currently in OMAP3 SPL, the GPMC for NAND is configured for 16bit
access. This patch adds support for 8bit NAND devices as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Conflict over SPDX changes means that one change was effectively dropped
as it was fixing typos in a removed hunk of text.
Conflicts:
arch/mips/cpu/mips64/start.S
Signed-off-by: Tom Rini <trini@ti.com>
Some version of Andes core support FPU coprocessor,
if this is the case, and toolchain support FPU instruction set,
we should enable it at low level initialization time.
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
Cc: Macpaul Lin <macpaul@gmail.com>
The timer_init function is called before relocation and writes to bss data
were corrupting relocation data. Fix this by removing the call to
reset_timer_masked. The initial timer count should be 0 or near 0 anyway,
so initializing the variables are not needed.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The 150MHz clock rate gives u-boot time functions problems and there's no
benefit to a fast clock, so lower the rate.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
interrupt_init also sets up the abort stack, but is not setup before
relocation. So any aborts during relocation will hang and not print out
any useful information. Fix this by moving the interrupt_init to after
the stack setup in board_init_f.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Synchronize the code with mips64/cache.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Synchronize the code with mips64/cache.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Synchronize the code with mips64/cache.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Make it similar to the code in mips{32,64}/start.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Synchronize the code with mips{32,64}/start.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Synchronize the code with mips{32,64}/start.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Synchronize the code with mips{32,64}/start.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Synchronize the code with mips{32,64}/start.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Make it similar to the code in mips64/start.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Synchronize the code with mips64/start.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
The t4 register already holds the cache
line size, and the value of the register
is not changed in mips_init_icache.
Get the cache line size value from t4 for
mips_init_dcache as well and remove the
superfluous assignment of t5 register.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Checking mips32/time.c with checkpatch.pl shows this:
arch/mips/cpu/mips32/time.c:30: WARNING: line over 80 characters
arch/mips/cpu/mips32/time.c:57: ERROR: return is not a function, parentheses are not required
total: 1 errors, 1 warnings, 0 checks, 85 lines checked
Fix the code to make checkpatch.pl happy.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Move the GT64120 register base to 0x1be00000
and setup PCI BAR registers as done by the
original YAMON bootloader.
This is needed for running Linux kernel.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
The MIPS Malta board has a SOFTRES register. Writing a
magic value into that register initiates a board reset.
Use this feature to implement reset support.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Add minimal support for the MIPS Malta CoreLV board
emulated by Qemu. The only supported peripherial is
the UART.
This is enough to boot U-Boot to the command prompt
both in little and big endian mode.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
On the origial Malta boards the REVISION register is
accessible at the 0x1fc00010 address. The contents of
this register gives information about the revision
of the Malta and Core Boards.
This register is used by the Linux kernel to identify
the actual board it is running on. However the register
is not emulated properly by Qemu, so put a hardcoded
value into the flash to make Linux work.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.
Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h
Signed-off-by: Tom Rini <trini@ti.com>
The timer3 counter unit for lastdesc and now values are inconsistent in current
code. The unit of "readl(&tmr->timer3_counter) / (CONFIG_SYS_CLK_FREQ / 2)" is
second. However, CONFIG_SYS_HZ is defined as 1000 in board config file.
This means the accuracy of "lastdec" and "now" should be in millisecond,
thus fix the equation to set lastdec and now variables accordingly.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Add a header file, setup.h, which copy from Linux source code,
this file contain structures are used to pass initialisation parameters
to Linux. Enable this function on adp-ag101/adp-ag101p target
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
Cc: Macpaul Lin <macpaul@gmail.com>
The original adp-ag101/adp-ag101p initialize only one bank(64MB)
by default at boot time, but it is not enough for some application,
so increasing to two banks(128M).
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
Cc: Macpaul Lin <macpaul@gmail.com>
U-Boot does not compile for the adp-ag101 boards since
commit f6c3b34697 (mmc:
update Faraday FTSDC010 for rw performance)
The driver assumes that the bit manipulation macros
are provided by all architectures. This is not the
case for nds32 and it causes a build error like this:
ftsdc010_mci.c: In function 'ftsdc010_clkset':
ftsdc010_mci.c:118: warning: implicit declaration of function 'setbits_le32'
ftsdc010_mci.c:123: warning: implicit declaration of function 'clrbits_le32'
drivers/mmc/libmmc.o: In function `ftsdc010_request':
/devel/u-boot.git/drivers/mmc/ftsdc010_mci.c:234: undefined reference to `setbits_le32'
/devel/u-boot.git/drivers/mmc/ftsdc010_mci.c:243: undefined reference to `clrbits_le32'
/devel/u-boot.git/drivers/mmc/ftsdc010_mci.c:234: undefined reference to `clrbits_le32'
drivers/mmc/libmmc.o: In function `ftsdc010_clkset':
/devel/u-boot.git/drivers/mmc/ftsdc010_mci.c:118: undefined reference to `clrbits_le32'
/devel/u-boot.git/drivers/mmc/ftsdc010_mci.c:118: undefined reference to `clrbits_le32'
/devel/u-boot.git/drivers/mmc/ftsdc010_mci.c:121: undefined reference to `setbits_le32'
/devel/u-boot.git/drivers/mmc/ftsdc010_mci.c:123: undefined reference to `setbits_le32'
/devel/u-boot.git/drivers/mmc/ftsdc010_mci.c:123: undefined reference to `setbits_le32'
The patch adds bit manipulation macros for the
nds32 architecture to avoid the errors. The macros
are copied from the ARM implementation.
Compile tested only.
Cc: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
CONFIG_I2C_MUX is replaced through the new i2c multibus/multiadapter
framework, configured through CONFIG_SYS_I2C. As CONFIG_I2C_MUX
is only used on the keymile boards, and they are now completely
moved to the new framework, remove CONFIG_I2C_MUX.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Holger Brunck <holger.brunck@keymile.com>
Tested-By: Holger Brunck <holger.brunck@keymile.com>
- added to fsl_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
- added to soft_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
CONFIG_SPL_BUILD creates debug TLB entry, so disable it before init_tlbs.
CONFIG_SPL_INIT_MINIMAL never creates any debug TLB entry, so no need
of disable_tlb().
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
MAKEALL is fine for ppc4xx and mpc85xx.
Run checks were done on our controlcenterd hardware.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Provide proper setting for the APLL fout frequency calculation for
Exynos4 based targets (especially Exynos4210 - Trats board).
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and
serial.
Conflicts:
arch/arm/dts/exynos5250.dtsi
Signed-off-by: Tom Rini <trini@ti.com>
The OS function is now always called with the PREP stage. Adjust the
remaining bootm OS functions to deal with this correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tegra30 and Tegra114 are compatible except PLL parameters.
Tested on Tegra30 Cardhu, and Tegra114 Dalmore
platforms. All works well.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add DT node for USB EHCI function.
Add support for T30-Cardhu, T30-Beaver, T114-Dalmore boards.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This function has no prototype in the headers and passes void * around, thus
requiring several casts. Tidy this up.
- Add new patch to clean up bootz_setup() function
Signed-off-by: Simon Glass <sjg@chromium.org>
There are differnce with clock calcuation by cpu variations.
This patch will fix it according to user manual.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
This patch performs the following:
1) Convert the assembly code for memory and clock initialization to C code.
2) Move the memory and clock init codes from board/samsung to arch/arm
3) Creat a common lowlevel_init file across Exynos4 and Exynos5. Converted
the common lowlevel_init from assembly to C-code
4) Made spl_boot.c and tzpc_init.c common for both exynos4 and exynos5.
5) Enable CONFIG_SKIP_LOWLEVEL_INIT as stack pointer initialisation is already
done in _main.
6) exynos-uboot-spl.lds made common across SMDKV310, Origen and SMDK5250.
TEST: Tested SD-MMC boot on SMDK5250 and Origen.
Tested USB and SPI boot on SMDK5250
Compile tested for SMDKV310.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch configures the gpio values for UART
on Origen and SMDKV310 using pinmux
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds APIs to get power reset status and exit the wakeup condition for
both exynos5 and exynos4
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The omap_gpio driver is used by AM33XX, OMAP3/4, OMAP54XX and DRA7XX SoCs.
These SoCs have different gpio count but currently omap_gpio driver uses hard
coded 192 which is wrong.
This patch fixes this issue by:
1. Move define of OMAP_MAX_GPIO to all arch/arm/include/asm/arch-omap*/gpio.h.
2. Update gpio bank settings and enable GPIO modules 7 & 8 clocks for OMAP5.
Thanks for Lubomir Popov to provide valuable comments to fix this issue.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Acked-by: Heiko Schocher <hs@denx.de>
During SDRAM_AUTO_DETECTION MA is not configured.
For Soc's > OMAP4460 MA is present. So populating
MA for the same.
Tested on OMAP4430 PANDA, OMAP4460 PANDA.
Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Fix the wrong mapping between the DDR I/O control registers on AM33XX
SoCs and the software representation in the SPL code.
The most recent public TRM defines the following DDR I/O control registers
offsets:
* ddr_cmd0_ioctrl : offset 0x44E11404
* ddr_cmd1_ioctrl : offset 0x44E11408
* ddr_cmd2_ioctrl : offset 0x44E1140C
* ddr_data0_ioctrl: offset 0x44E11440
* ddr_data1_ioctrl: offset 0x44E11444
While the struct ddr_cmdtctrl has also some reserved bits in the beginning.
The struct is mapped to the address 0x44E11404. As a result "cm0ioctl" points
to the ddr_cmd1_ioctrl register, "cm1ioctl" to the ddr_cmd2_ioctrl and etc.
Registers ddr_cmd0_ioctrl and ddr_data0_ioctrl are never configured because
of this mapping mismatch.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Commit 35fc84fa1f broke bootm on avr32. It
requires to call do_bootm_linux() with flag set to BOOTM_STATE_OS_PREP before
calling it again with flag set to BOOTM_STATE_OS_GO.
Fix this by allowing flag set to BOOTM_STATE_OS_PREP, this however will
require a complete refactoring later on.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
[trini: Apply to m68k, microblaze, nds32, nios2, openrisc, sh and sparc]
Signed-off-by: Tom Rini <trini@ti.com>
Patch 35fc84fa1 [Refactor the bootm command to reduce code duplication]
breaks booting Linux (compressed uImage with fdt) on powerpc.
boot_jump_linux() mustn't be called before boot_prep_linux() and
boot_body_linux() have been called. So remove the superfluous call
to boot_jump_linux() in arch/powerpc/lib/bootm.c as its called later on
in this function.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@ti.com>
enum boot_mode is defined twice once in spl.h and also in
spl_boot.c, hence removing the same from spl_boot.c and including
the header file.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
SDRAMC_DARCn_BA() macro worked fine when the BA is 0x00000000 even
though the macro is incorrect. It causes the BA to be set incorrctly
for other base addresses. This patch fixes the macro so that base
addresses other than zero can be used with the MCF5235.
Signed-off-by: Steve deRosier <derosier@gmail.com>
There is a debug call in board.c befor serial interface was initialized.
This moves the debug code behind serial_initialize call.
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Some changes are needed to x86 timer functions to support tracing. Add
these so that the feature works correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
For tracing to work it has to be able to access the microsecond timer
without causing a recursive call to the function entry/exit handlers.
Add attributes to the relevant functions to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Implement this feature on ARM for tracing.
It would be nice to have generic bootm support so that it is easily
implemented on any arch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
At present the arguments to bootm are processed in a somewhat confusing
way. Sub-functions must know how many arguments their calling functions
have processed, and the OS boot function must also have this information.
Also it isn't obvious that 'bootm' and 'bootm start' provide arguments in
the same way.
Adjust the code so that arguments are removed from the list before calling
a sub-function. This means that all functions can know that argv[0] is the
first argument of which they need to take notice.
Signed-off-by: Simon Glass <sjg@chromium.org>
Support tracing on sandbox by adding suitable CONFIG options. To enable it,
compile U-Boot with FTRACE=1.
The timer functions are marked to skip tracing, since these are called from
the tracing code itself, and we want to avoid an infinite loop.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch adds cros-ec related device nodes to exynos5250-snow.dts.
It also adds a gpio node to exynos5250.dtsi.
Signed-off-by: Hung-ying Tyan <tyanh@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This patch adds the device node required for serial driver
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
On the xscale, the icache must be invalidated and the write buffers drained
after writing code over the data bus, even if the caches are disabled. Tested
on the pxa270.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Pass '-mcpu=xscale' to the compiler instead of march and mtune. This will cause
gcc to define the __XSCALE__ macro.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
The comment in the low-level initialization function cpu_init_crit() says that
the caches are being disabled, but (oddly) the icache is actually turned on.
This is probably not a good idea prior to relocating code, so this patch turns
it off. Tested on the pxa270.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
This change is only done where needed: some linker
scripts may contain relocation symbols yet remain
unchanged.
__rel_dyn_start and __rel_dyn_end each requires
its own output section; putting them in relocation
sections changes their flags and breaks relocation.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This change is only done where needed: some linker
scripts may contain __image_copy_{start,end} yet
remain unchanged.
Also, __image_copy_end needs its own section; putting
it in relocation sections changes their flags and makes
relocation break.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
File arch/arm/lib/bss.c was initially defined for BSS only,
but is now going to also contain definitions for other
section-boundary-related symbols, so rename it for better
accuracy.
Also, remove useless 'used' attributes.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Discard all .dynsym sections from linker scripts
Remove all __dynsym_start definitions from linker scripts
Remove all __dynsym_start references from the codebase
Note: this touches include/asm-generic/sections.h, which
is not ARM-specific, but actual uses of __dynsym_start
are only in ARM, so this patch can safely go through
the ARM repository.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Add a Makefile target ('checkarmreloc') which
fails if the ELF binary contains relocation records
of types other than R_ARM_RELATIVE.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
init_tlbs() initialize all the TLB entries required for the system.
So disable DEBUG TLB entry before TLB entries initialization.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
If a variable is used as array subscript, it's valid value range is
0 ... ARRAY_SIZE -1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
There will clear the BSS in the function clear_bss(), the reset address of
the BSS started from the __bss_start, and increased by four-byte increments,
finally stoped depending on the address is equal to the _bss_end. If the end
address __bss_end is not alignment to 4byte, it will be an infinite loop.
1. The reset action stoped depending on the reset address is greater
than or equal the end address of the BSS.
2. The end address of the BSS should be 4byte aligned. Because the reset unit
is 4 Bytes.
This patch is on top of the patch "powerpc/mpc85xx: support application
without resetvec segment in the linker script".
Signed-off-by: Ying Zhang <b40530@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
For SD/SPI 2-stage bootloader, the On-Chip Rom code loads the SPL into L2 SRAM,
then jump to it to begin execution. After that, the SPL loads the final uboot
image into DDR, then jump to it to begin execution. The segment .resetvec in
the SPL and in final U-boot is useless.
So, add new symbols CONFIG_SYS_MPC85XX_NO_RESETVEC for this application.
If CONFIG_SYS_MPC85XX_NO_RESETVEC is set, the segment .resetvec is excluded
and the segment .bootpg is placed in the previous 4K of the segment .text.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Erratum A-006593 is "Atomic store may report failure but still allow
the store data to be visible".
The workaround is: "Set CoreNet Platform Cache register CPCHDBCR0 bit
21 to 1'b1. This may have a small impact on synthetic write bandwidth
benchmarks but should have a negligible impact on real code."
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Calculate reserved fields according to IFC bank count
1. Move csor_ext register behind csor register and fix res offset
2. Move ifc bank count to config_mpc85xx.h to support 8 bank count
3. Guard fsl_ifc.h with CONFIG_FSL_IFC macro to eliminate the compile
error on some devices that does not have IFC controller.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When a T4 board boots from SRIO or PCIE, it needs to finish these processes:
1. Set all the cores in holdoff status.
2. Set the boot location to one PCIE or SRIO interface by RCW.
3. Set a specific TLB entry for the boot process.
4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot.
5. Set a specific TLB entry in order to fetch ucode and ENV from
master.
6. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
7. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
For more information about the feature of Boot from SRIO/PCIE, please
refer to the document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When a b4860qds board boots from SRIO or PCIE, it needs to finish these
processes:
1. Set all the cores in holdoff status.
2. Set the boot location to one PCIE or SRIO interface by RCW.
3. Set a specific TLB entry for the boot process.
4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot.
5. Set a specific TLB entry in order to fetch ucode and ENV from
master.
6. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
7. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
For more information about the feature of Boot from SRIO/PCIE, please
refer to the document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Currently, the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" can enable
the master module of Boot from SRIO and PCIE on a platform. But this
is not a silicon feature, it's just a specific booting mode based on
the SRIO and PCIE interfaces. So it's inappropriate to put the macro
into the file arch/powerpc/include/asm/config_mpc85xx.h.
Change the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" to
"CONFIG_SRIO_PCIE_BOOT_MASTER", remove them from
arch/powerpc/include/asm/config_mpc85xx.h file, and add those macros
in configuration header file of each board which can support the
master module of Boot from SRIO and PCIE.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Freescale documentation presents the PowerPC core names in lower case, such as
"e300", "e500", "e600", etc.
Change the upper case occurrences into lower case so that the core names
reported in U-boot can match the ones from the documentation.
While at it also fix a checkpatch error:
ERROR: space prohibited before that close parenthesis ')'
#53: FILE: arch/powerpc/cpu/mpc86xx/cpu.c:81:
+ printf("e600 Core %d", (msscr0 & 0x20) ? 1 : 0 );
Reported-by: Heinz Wrobel <heinz.wrobel@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
BSC9131RDB is a Freescale Reference Design Board for
BSC9131 SoC which is a integrated device that contains
one powerpc e500v2 core and one DSP starcore.
To support DSP starcore
-Creating LAW and TLB for DSP-CCSR space.
-Creating LAW for DSP-core subsystem M2 memory
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Linker script is not able find start.o binary. So add its absolute path in
u-boot-spl.lds. This change is similar to u-boot-nand.lds
common/Makefile: Avoid compiling unnecssary files
fsl_ifc_spl.c : It is is responsible for reading u-boot binary from
NAND flash and copying into DDR. It also transfer control from NAND SPL
to u-boot image present in DDR.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
IFC errata A003399 is valid for IFC NOR boot i.e.if no on-board NOR flash or
no NOR boot, do not compile its workaround.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
To avoid sign extension problem, use explicit casting to cast
the SDRAM size to type phys_size_t, or else, if the SDRAM size
is 2G(0x80000000), it will be extended to 0xffffffff80000000
when phys_size_t is type 'unsigned long long'.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Accidentally applied an earlier version of the patch, which set
the compatible to "fsl,qoriq-clockgen-2", lacking the final
".0".
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
move uart soft reset code to common place and call
this function from board code, instead of copy and paste
this code for every board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Tom Rini <trini@ti.com>
[trini: Fix igep0033 build, remove 'regval' on pcm051]
Signed-off-by: Tom Rini <trini@ti.com>
upcoming support for siemens boards switches mpu pll clk in board
code. So make this configurable.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
move rtc32k_enable() to common place so all am33xx boards can use it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR
Conflicts:
arch/arm/include/asm/arch-omap5/omap.h
Signed-off-by: Tom Rini <trini@ti.com>
This patch does the folowing
1. change the data types for unsigned int variable to unsigned
2. change the tmu_base type to struct exynos5_tmu_reg *
3. Add timer functionality for get_cur_temp()
4. error handling in the get_tmu_fdt_values()
5. Add check for curr_temp reading
6. some cosmotic changes.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Vadim Bendebury <vbendeb@google.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch initialises the local variable 'shift' to zero.
The uninitialised local variable 'shift' had garbage value and was
resulting in unwnated results in the functions exynos5_get_mmc_clk()
and exynos4_get_mmc_clk().
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds FDT support for DWMMC, by reading the DWMMC node data
from the device tree and initialising DWMMC channels as per data
obtained from the node.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds DWMMC device node data for exynos5.
This patch also adds binding file for DWMMC device node.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
PXA270 CPU has turbo mode. The mode is 2.5 times faster than the
default run mode. Activating the mode early significantly speeds
up boot process.
Signed-off-by: Sergey Yanovich <ynvich@gmail.com>
C99's strict aliasing rules are insane to use in low-level code such as a
bootloader, but as Wolfgang has rejected -fno-strict-aliasing in the
past, add a union so that 16-bit accesses can be performed.
Compile-tested only.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Move pinmux configurations for the DA830 SoCs from board file
to the arch tree so that it can be used for all da830 based devices.
Also, avoids duplicate pinmuxing in case of NAND.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
auxclk0 and auxclk1 are utilized on some OMAP5 boards.
Define the infrastructure needed for accessing them
without using magic numbers.
Also remove unrelated TPS62361 defines from clocks.h
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
The omap2420H4 was the only mainline omap24xx board. Prior to being
fixed by Jon Hunter in time for v2013.04 it had been functionally broken
for a very long time. Remove this board as there's not been interest in
it in U-Boot for quite a long time.
Signed-off-by: Tom Rini <trini@ti.com>
DRA7 EVM board has the below configuration. Adding the
settings for the same here.
2Gb_1_35V_DDR3L part * 2 on EMIF1
2Gb_1_35V_DDR3L part * 4 on EMIF2
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Update PLL values.
SYS_CLKSEL value for 20MHz is changed to 2. In other platforms
SYS_CLKSEL value 2 represents reserved. But in sys_clk array
ind 1 is used for 13Mhz. Since other platforms are not using
13Mhz, reusing index 1 for 20MHz.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
NON SECURE SRAM is 512KB in DRA7xx devices.
So fixing it here.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The sys_clk on the dra evm board is 20MHZ.
Changing the configuration for the same.
And also moving V_SCLK, V_OSCK defines to
arch/clock.h for OMAP4+ boards.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Slew rate compensation cells are not present for DRA7xx
Soc's. So return from function srcomp_enable() if soc is not
OMAP54xx.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
DRA752 now uses AVS Class 0 voltages which are voltages in efuse.
This means that we can now use the optimized voltages which are
stored as mV values in efuse and program PMIC accordingly.
This allows us to go with higher OPP as needed in the system without
the need for implementing complex AVS logic.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In DRA7xx Soc's voltage scaling is done using GPI2C.
So i2c_init should happen before scaling. I2C driver
uses __udelay which needs timer to be initialized.
So moving timer_init just before voltage scaling.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
TPS659038 is the power IC used in DRA7XX boards.
Adding support for this and also adding pmic data
for DRA7XX boards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The registers that are used for device identification
are changed from OMAP5 to DRA7xx.
Using the correct registers for DRA7xx.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Voltage scaling can be done in two ways:
-> Using SR I2C
-> Using GP I2C
In order to support both, have a function pointer in pmic_data
so that we can call as per our requirement.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
SGX clocks should be enabled only for OMAP5 ES1.0.
So this can be removed.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
After having the u-boot clean up series, there are
many definitions that are unused in header files.
Removing all those unused ones.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The newly introduced function setup_warmreset_time(), called
from within prcm_init(), tries to write to the prm_rsttime
OMAP5 register. The struct member holding this register's
address is however initialized for OMAP5 ES2.0 only. On ES1.0
devices this uninitialized value causes a second (warm) reset
at startup.
Add .prm_rsttime address init to the ES1.0 struct.
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
Acked-by: Tom Rini <trini@ti.com>
Patch adds a call of abb_setup() function, and proper registers
definitions needed for ABB setup sequence. ABB is initialized
for MPU voltage domain.
Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
Adaptive Body Biasing (ABB) modulates transistor bias voltages
dynamically in order to optimize switching speed versus leakage.
Adaptive Body-Bias ldos are present for some voltage domains
starting with OMAP3630. There are three modes of operation:
* Bypass - the default, it just follows the vdd voltage
* Foward Body-Bias - applies voltage bias to increase transistor
performance at the cost of power. Used to operate safely at high
OPPs.
* Reverse Body-Bias - applies voltage bias to decrease leakage and
save power. Used to save power at lower OPPs.
Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
This fixes several warnings like
In file included from ./u-boot/include/linux/mtd/mtd.h:13:0,
from env_onenand.c:37:
./u-boot/build/vct_platinumavc_onenand_small/include2/asm/errno.h:52:0: warning: "ENOMSG" redefined [enabled by default]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The purpose of the __raw* IO accessors is to provide
IO access in native-endian order. However in the current
MIPS implementation, the 16 and 32 bit variants of the
__raw accessors are swapping the values on big-endian
systems if the CONFIG_SWAP_IO_SPACE option is enabled.
The patch changes the IO accessor macros to fix this
broken behaviour.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
The non-SPL build of U-Boot on Tegra only runs on a single CPU, and
hence there is no need to enable the SCU when running U-Boot. If an
SMP OS is booted, and it needs the SCU enabled, it will enable the SCU
itself. U-Boot doing so is redundant.
The one exception is Tegra20, where an enabled SCU is required for some
aspects of PCIe to work correctly.
Some Tegra SoCs contain CPUs without a software-controlled SCU. In this
case, attempting to turn it on actively causes problems. This is the case
for Tegra114. For example, when running Linux, the first (or at least
some very early) user-space process will trigger the following kernel
message:
Unhandled fault: imprecise external abort (0x406) at 0x00000000
This is typically accompanied by that process receving a fatal signal,
and exiting. Since this process is usually pid 1, this causes total
system boot failure.
Signed-off-by: Tom Warren <twarren@nvidia.com>
[swarren, fleshed out description, ported to upstream chipid APIs]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The location of valid scratch space is dependent on SoC, so move that
there. On OMAP4+ we continue to use SRAM_SCRATCH_SPACE_ADDR. On
am33xx/ti814x we want to use what the ROM defines as "public stack"
which is the area after our defined download image space. Correct the
comment about and location of CONFIG_SPL_TEXT_BASE.
Signed-off-by: Tom Rini <trini@ti.com>
We need to call the save_omap_boot_params function on am33xx/ti81xx and
other newer TI SoCs, so move the function to boot-common. Only OMAP4+
has the omap_hw_init_context function so add ifdefs to not call it on
am33xx/ti81xx. Call save_omap_boot_params from s_init on am33xx/ti81xx
boards.
Reviewed-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Prior to Sricharan's cleanup of the boot parameter saving code, we
did not make use of NON_SECURE_SRAM_START on am33xx, so it wasn't a
problem that the address was pointing to the middle of our running SPL.
Correct to point to the base location of the download image area.
Increase CONFIG_SPL_TEXT_BASE to account for this scratch area being
used. As part of correcting these tests, make use of the fact that
we've always been placing our stack outside of the download image area
(which is fine, once the downloaded image is run, ROM is gone) so
correct the max size test to be the ROM defined top of the download area
to where we link/load at.
Signed-off-by: Tom Rini <trini@ti.com>
---
Changes in v2:
- Fix typo noted by Peter Korsgaard
This requires that cpu_is_exynos4/5 should be made available before tzpc_init.
Hence this patch also makes necessary changes to have cpu_info in spl and
invokes arch_cpu_init before tzpc_init in low_level_init.S for smdk5250.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Acked-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
tzpc_init is common for all exynos5 boards, hence move it to
armv7/exynos so that all other boards can use it.
Also update the smdk5250 Makefile and config file.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Acked-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The vectoring table has to be placed at 0x0, but U-Boot on MX23/MX28
starts from RAM, so the vectoring table at 0x0 is not present. Craft
code that will be placed at 0x0 and will redirect interrupt vectoring
to proper location of the U-Boot in RAM.
Signed-off-by: Marek Vasut <marex@denx.de>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch adds generic codes to support Freescale's Vybrid VF610 CPU.
It aligns Vybrid VF610 platform with i.MX platform. As there are
some differences between VF610 and i.MX platforms, the specific
codes are in the arch/arm/cpu/armv7/vf610 directory.
Signed-off-by: Alison Wang <b18965@freescale.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This patch adds the IOMUX support for Vybrid VF610 platform.
There is a little difference for IOMUXC module between VF610 and i.MX
platform, the muxmode and pad configuration share one 32bit register on
VF610, but they are two independent registers on I.MX platform. A
CONFIG_IOMUX_SHARE_CONFIG_REG was introduced to fit this difference.
Signed-off-by: Alison Wang <b18965@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Replace all relocate_code routines from ARM start.S files
with a single instance in file arch/arm/lib/relocate.S.
For PXA, this requires moving the dcache unlocking code
from within relocate_code into c_runtime_cpu_setup.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Simon Glass <sjg@chromium.org>
