Add configuration for the MT41K128M16JT125K memory modules as used on the
Bosch Guardian device.
Based on a patch by:
Govindaraji Sivanantham <Govindaraji.Sivanantham@in.bosch.com>
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
[checkpatch.pl cleanup by Martyn Welch]
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
This patch adds dt node for DP83867 phy used on K2G ICE board and
also enable netcp device nodes for the board.
EVM hardware spec recommends to add 0.25 nsec delay in the tx
direction and 2.25 nsec delay in the rx direction for internal
delay in the clock path to be on the safer side.
The board straps RX_DV/RX_CTRL pin of on board DP83867 phy in mode
1. Unfortunately, the phy data manual disallows this. Add
ti,dp83867-rxctrl-strap-quirk in the phy node to allow software to
enable workaround suggested for this incorrect strap setting. This
ensures proper operation of this PHY.
The dts bindings are kept in sync with that from 4.14.y linux
kernel. This required the pinmux device related bindings to be
commented out to allow for compilation.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch removes the unused phy-mode property from the phy dt node. On
K2G, currently link-interface determines if phy is used or not and is
already set to use rgmii. So this is not needed. Besides phy-mode should
be added to slave interface configuration of the cpsw driver, not in the
phy node.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds a workaround to reset the phy one time during boot
using GPIO0 pin 10 to make sure, the Phy latches the configuration
from the input pins correctly.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This add pinmux configuration for rgmii interface so that network
driver can be supported on K2G ICE boards. The pinmux configurations
for this are generated using the pinmux tool at
https://dev.ti.com/pinmux/app.html#/default
As this required some BUFFER_CLASS definitions, same is re-used
from the linux defnitions in include/dt-bindings/pinctrl/keystone.h
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Sync armada-385-db-88f6820-amc.dts with Linux. Retain the
u-boot,dm-pre-reloc and nand differences.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This board was added to u-boot first but the Linux maintainers requested
a more descriptive name. Rename the file to match the Linux usage and
update the board defconfig.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Commit 93b283d49f ("ARM: CPU: arm926ejs: Consolidate cache routines to
common file") changed cache setup for Kirkwood such that icache_enable()
is now called from enable_caches() which is called from initr_caches()
which is in the list of functions in init_sequence_r[] prior to
arch_misc_init(). This means the call to icache_enable() in
arch_misc_init() is no longer required, so remove it.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The DB-XC3-24G4XG is a switch development board from Marvell. It can
either use and external CPU card such as the db-88f6820-amc or the
internal CPU that is integrated into the switch.
Add support for running U-Boot on the internal CPU and enable the USB,
SPI and NAND peripherals. For now this needs the bin_hdr from the
Marvell U-Boot for this board.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
One difference with the integrated CPUs is that they use a different
clock control block to the Armada devices. Update mvebu_get_nand_clock()
accordingly.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Marvell's switch chips with integrated CPUs (collectively referred to as
MSYS) share common ancestry with the Armada SoCs. Some of the IP blocks
(e.g. xor) are located at different addresses and DFX server exists as a
separate target on the MBUS (on Armada-38x it's just part of the core
complex registers).
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
We now have MEVBU boards without SPL support (e.g. db-xc3-24g4xg).
Because of this, a new compile time warning from Kconfig is show:
WARNING: unmet direct dependencies detected for SPL_OF_CONTROL
Depends on [n]: SUPPORT_OF_CONTROL [=y] && SPL [=n] && OF_CONTROL [=y]
Selected by [y]:
- ARMADA_32BIT [=y] && ARM [=y] && ARCH_MVEBU [=y]
WARNING: unmet direct dependencies detected for SPL_DM
Depends on [n]: DM [=y] && SPL [=n]
Selected by [y]:
- ARMADA_32BIT [=y] && ARM [=y] && ARCH_MVEBU [=y]
...
This patch fixes this issue and removes these warnings.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
This patch enables the PCIe port specific link capabilities configuration
for Armada XP. The weak function board_sat_r_get() was used to return
a common flag for PCIe Gen1 vs Gen2 capability for all PCIe ports. This
is now changed with this patch to return a bit per PCIe port (4 bits
in this case, bit 0 for PCIe port 0, etc).
The theadorable board uses this new feature to configure PCIe port 0
as Gen1 and all other PCIe ports as Gen2 capable. All other AXP boards
using this function are not changed in the configuration and still
configure all ports as PCIe Gen2.
This patch also removes the parameter "pex_mode" from
board_serdes_cfg_get() as this parameter was not used in any of the
implementations.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
This allows the ahci_mvebu driver to do A38x platform specific
configuration at initialization.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Now that kirkwood is using the mvebu mbus this function is no longer
needed.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The mvebu mbus code already had most of the support required for
kirkwood. The only difference is that unlike the other mvebu targets
kirkwood doesn't have a bridge control block so the code related to
managing that needs to be compiled out.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
KW_DEFADR_PCI_IO_REMAP has the same value as KW_DEFADR_PCI_IO and is
only used to set up a 1:1 mapping. Remove it and update the mapping to
use KW_DEFADR_PCI_IO.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This will allow the kirkwood platforms to use more common code with the
other mvebu SoCs.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable the hardware watchdog to guard against system lock ups when
running in the SPL or U-Boot. Stop the watchdog just before booting so
that the OS can re-enable it if needed.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Bring in the Armada 370/XP dts/dtsi files from Linux. As U-Boot hasn't
got the new NAND driver the updating binding has not been included.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add DT node for MCU NAVSS its components to get DMA working on AM654
SoC.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Merge drivers/soc/keystone/ into drivers/soc/ti/
and convert CONFIG_TI_KEYSTONE_SERDES into Kconfig.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Texas Instruments' System Control Interface (TI-SCI) Message Protocol
abstracts management of NAVSS resources, like PSI-L pairing and
unpairing, UDMAP tx/rx/flow configuration and Rings.
This patch adds support for requesting and configuring such resources
from TI-SCI firmware.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
On modern Allwinner SoCs (tested: H2+, A64, H5, H6) the BootROM can
actually load the SPL also from sector 256 (128KB) of an SD card or eMMC
chip. For more details, see [1].
In this case the boot source indicator (written at offset 0x28 of SRAM A1)
has bit 4 set, so it's 0x10 for SD card and 0x12 for eMMC.
Add those new values to the existing boot source check to allow booting
the SPL from those "high" disk offsets as well. For this to work, the
value of CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR needs to be adjusted,
for instance to 0x140 (right after the high SPL). Doing this dynamically
sounds desirable, but looks nasty to implement.
[1] https://groups.google.com/forum/#!topic/linux-sunxi/MaiijyaAFjk
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Most of the boards we support with H3/H5 enable DRAM on-die termination,
which is consistent with the high DRAM clocks that are used.
Make it the default (like it's done for other similar platforms) instead
of defining it in each defconfig.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Most H3/H5 boards we support have the DRAM ZQ value set to 3881979,
which is also consistent with the default set for the R40.
Make this value the default on H3/H5 instead of 123.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
A few sun8i platforms define specific default DRAM ZQ values, but they
are not taken in account because of MACH_SUN8I being used for the 123
default first.
Replace MACH_SUN8I with the list of platforms that don't have specific
DRAM ZQ values, to avoid overwriting the default for those that do.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
While the exact problem is not known, based on discussion between
Philipp Tomsich and André Przywara it is guessed that exit self-refresh
timing is not set with correct value. There may be implicit enter or
exit Self-Refresh anywhere as part of some training phase.
In ZynqMP register guide [1], which is close to the various
Allwinner DRAM controllers, tXSDLL is bits [14:8], while the non-DLL
tXS is bits [6:0]: Self refresh exit delay. So it could be safely
increased and it only affects the time after the self-refresh “exit”,
which happens only after (re-)initialisation.
There was no document for cpu in question so based on oscilloscope
readings [2][3] and observed result by comparing allwinner architecture.
So set it same as Allwinner H5 silicon.
Before this patch, failure rate of was 7%.
This was tested on A33 allwinner cpu, dual rank connection connected
with two MT41K512M16HA-125:A memory model. Memory is configured as DDR3
1.5V
And also this is tested in A33-OLinuXino dev board.
[1] https://www.xilinx.com/html_docs/registers/ug1087/ddrc___dramtmg8.html
[2] https://ibb.co/R70zmyS
[3] https://ibb.co/HVVCGQ8
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Acked-by: Jagan Teki <jagan@openedev.com>
The E2 Alt board has two USB ports, add missing DT nodes to make the
USB available.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Synchronize R-Car Gen3 device trees with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Synchronize R-Car Gen2 device trees with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add pin control tables for R8A77965 from Linux 5.0 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add clock tables for R8A77965 from Linux 5.0 , except for the
crit, R and Z clock, which are neither used nor supported by
the U-Boot clock framework yet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable LZO compression of the multi-DTB fitImages, since the U-Boot
with multiple DTs enabled is becoming quite large and the DTs can
be well compressed. The LZO compression saves almost 200 kiB on the
Salvator-X(S) and ULCB targets.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The ATF can pass additional information via the first four registers,
x0...x3. The R-Car Gen3 with mainline ATF, register x1 contains pointer
to a device tree with platform information. Save these registers for
future use.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcrEcDAAoJEB6zHgIOrC/I1dgH/3mHQNW8bqiNCJYcoVQdheHb
e06TqbWHNlOG/NilYybvdeF+LjeCqhX4PzyL/sdcyBf3D/tK4cVvHpZrQyjb2s6K
5IZSKJ+cZznmq6Hv7b//d30Azhx8bi8luxs60kkj+PF0xI1EyU3JteUqAs4Ooxd7
z+HdcRFuAaps6sy0+szB3fTw9HTGrhFvQuHasDGb2uahhpwGzu/P0RchIDksOdzH
3L4EOvgq8MZCiZ3ZtFWMWzQoCjcKf5Fuux41qar8gG/LrkWRfKG+LfWfZtTiTsjf
vC9bYWmdKtkSLFj1PWgLBfGxev5zwPUbqI2EP4OlagfNs3os5pVFCYV5NZ6ovdE=
=kMXf
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2019.07-a' of git://git.denx.de/u-boot-atmel
First set of u-boot-atmel features and fixes for 2019.07 cycle
The GARDENA smart Gateway boards are equipped with an Atmel / Microchip
AT91SAM9G25 SoC and with 128 MiB of RAM and 256 MiB of NAND storage.
This patch adds support for this board including SPL support. Therefore
the AT91Boostrap is not needed on this platform any more.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This makes it possible to reference the watchdog DT node via "&watchdog"
from board dts files.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This patch adds _image_binary_end to the SPL linker script. This will be
used be the upcoming GARDENA AT91SAM based platform, which uses DT in
SPL and configures CONFIGURE_SPL_SEPARATE_BSS.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This patch enables and starts the watchdog on the AT91 platform if
configured. The WD timeout value is read in the AT91 WD device driver
from the DT, using the "timeout-sec" DT property. If not provided in
the DT, the default value of 2 seconds is used.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
This patch adds a call to spl_early_init() to board_init_f() which is
needed when CONFIG_SPL_OF_CONTROL is configured. This is necessary for
the early SPL setup including the DTB setup for later usage.
Please note that this call might also be needed for non SPL_OF_CONTROL
board, like the smartweb target. But smartweb fails to build with this
call because its binary grows too big. So I disabled it for these kind
of targets for now.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested on the taurus board:
Tested-by: Heiko Schocher <hs@denx.de>
Make sure that lowlevel_init is not compiled when
CONFIG_SKIP_LOWLEVEL_INIT_ONLY is configured.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested on the taurus board:
Tested-by: Heiko Schocher <hs@denx.de>
Migrate the following options to CONFIG_DM:
CONFIG_DM_GPIO
CONFIG_DM_MMC
CONFIG_DM_ETH
CONFIG_DM_SERIAL
CONFIG_DM_USB
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
When introducing the SAMA5D27 SoCs, the SAMA5D2 series got an additional
chip id. The check if the cpu is sama5d2 was changed from a preprocessor
definition (inlining a call to 'get_chip_id()') to a C function,
probably to not call get_chip_id twice?
That however broke a check in the macb ethernet driver. That driver is
more generic and also used for other platforms. I suppose this solution
was implemented to use it in 'gem_is_gigabit_capable()', without having
to stricly depend on the at91 platform:
#ifndef cpu_is_sama5d2
#define cpu_is_sama5d2() 0
#endif
That only works as long as cpu_is_sama5d2 is a preprocessor definition.
(The same is still true for sama5d4 by the way.) So this is a straight
forward fix for the workaround.
The not working check on the SAMA5D2 CPU lead to an issue on a custom
board with a LAN8720A ethernet phy connected to the SoC:
=> dhcp
ethernet@f8008000: PHY present at 1
ethernet@f8008000: Starting autonegotiation...
ethernet@f8008000: Autonegotiation complete
ethernet@f8008000: link up, 1000Mbps full-duplex (lpa: 0xffff)
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
BOOTP broadcast 6
BOOTP broadcast 7
BOOTP broadcast 8
BOOTP broadcast 9
BOOTP broadcast 10
BOOTP broadcast 11
BOOTP broadcast 12
BOOTP broadcast 13
BOOTP broadcast 14
BOOTP broadcast 15
BOOTP broadcast 16
BOOTP broadcast 17
Retry time exceeded; starting again
Notice the wrong reported link speed, although both SoC and phy only
support 100 MBit/s!
The real issue on reliably detecting the features of that cadence
ethernet mac IP block, is probably more complicated, though.
Fixes: 245cbc583d ("ARM: at91: Get the Chip ID of SAMA5D2 SiP")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Enabling DM_MMC is forcing CONFIG_BLK=y so if any board which uses
SCSI must need to enable DM_SCSI otherwise SCSI reads on that particular
target making invalid reading to the disk drive.
Allwinner platform do support SCSI on A10, A20 and R40 SoC's out of
these only A10 have DM_SCSI enabled. So enabling DM_MMC on A20, R40
would eventually end-up with scsi disk read failures like [1]
So, enable DM_MMC in all places of respective SoC's instead of enabling
them globally to Allwinner platform.
Now, DM_MMC is enabled in Allwinner SoC's except A20 and R40.
[1] https://lists.denx.de/pipermail/u-boot/2019-April/364057.html
Reported-by: Pablo Sebastián Greco <pgreco@centosproject.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This patch moves all instances of static "watchdog_dev" declarations to
the "data" section. This may be needed, as the BSS may not be cleared
in the early U-Boot phase, where watchdog_reset() is already beeing
called. This may result in incorrect pointer access, as the check to
"!watchdog_dev" in watchdog_reset() may not be true and the function
may continue to run.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Marek Behún" <marek.behun@nic.cz>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
It occurs since commit 27cb7300ff
("Ensure device tree DTS is compiled").
More details can refer to
89c2b5c020
ARM: fix arch/arm/dts/Makefile
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Limit the cache configuration only can be supported in M mode.
It can not be manipulated in S mode.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Add ax25 RISC-V platform-specific Kconfig options,
to include CPU and timer drivers. Also disable
ATCPIT100 SoC timer and replace by PLMT.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
The platform-Level Machine Timer (PLMT) block
holds memory-mapped mtime register associated
with timer tick.
This driver implements the riscv_get_time() which
is required by the generic RISC-V timer driver.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
The Platform-Level Interrupt Controller (PLIC)
block holds memory-mapped claim and pending registers
associated with software interrupt. It is required
for handling IPI.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Print an error message and hang if smp_call_function() returns an error,
indicating that relocation of the secondary harts has failed.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
RISC-V U-Boot expects the hart ID to be passed to it via register a0 by
the previous boot stage. Machine mode firmware such as BBL and OpenSBI
do this when starting their payload (U-Boot) in supervisor mode. If
U-Boot is running in machine mode, this task must be handled by the boot
ROM. Explicitly populate register a0 with the hart ID from the mhartid
CSR to avoid possible problems on RISC-V processors with a boot ROM that
does not handle this task.
Suggested-by: Rick Chen <rick@andestech.com>
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Rick Chen <rick@andestech.com>
On RISC-V, all harts boot independently. To be able to run on a
multi-hart system, U-Boot must be extended with the functionality to
manage all harts in the system. All harts entering U-Boot are registered
in the available_harts mask stored in global data. A hart lottery system
as used in the Linux kernel selects the hart U-Boot runs on. All other
harts are halted. U-Boot can delegate functions to them using
smp_call_function().
Every hart has a valid pointer to the global data structure and a 8KiB
stack by default. The stack size is set with CONFIG_STACK_SIZE_SHIFT.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
The hart ID passed by the previous boot stage is currently stored in
register s0. If we divert the control flow inside a function, which is
required as part of multi-hart support, the function epilog may not be
called, clobbering register s0. Save the hart ID in the unallocatable
register tp instead to protect the hart ID.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Move the initialization of the caches and the debug UART until after
board_init_f_init_reserve. This is in preparation for SMP support, where
code prior to this point will be executed by all harts. This ensures
that initialization will only be performed once on the main hart running
U-Boot.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The supervisor binary interface (SBI) provides the necessary functions
to implement the platform IPI functions riscv_send_ipi() and
riscv_clear_ipi(). Use it to implement them.
This adds support for inter-processor interrupts (IPIs) on RISC-V CPUs
running in supervisor mode. Support for machine mode is already
available for CPUs that include the SiFive CLINT.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Import the supervisor binary interface (SBI) header file from Linux
(arch/riscv/include/asm/sbi.h). The last change to it was in commit
6d60b6ee0c97 ("RISC-V: Device, timer, IRQs, and the SBI").
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Harts on RISC-V boot independently, U-Boot is responsible for managing
them. Functions are called on other harts with smp_call_function(),
which sends inter-processor interrupts (IPIs) to all other available
harts. Available harts are those marked as available in the device tree
and present in the available_harts mask stored in global data. The
available_harts mask is used to register all harts that have entered
U-Boot. Functions are specified with their address and two function
arguments (argument 2 and 3). The first function argument is always the
hart ID of the hart calling the function. On the other harts, the IPI
interrupt handler handle_ipi() must be called on software interrupts to
handle the request and call the specified function.
Functions are stored in the ipi_data data structure. Every hart has its
own data structure in global data. While this is not required at the
moment (all harts are expected to boot Linux), this does allow future
expansion, where other harts may be used for monitoring or other tasks.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
After the commit: "eth: dm: fec: Add gpio phy reset binding"
SHA1: efd0b79106
The FEC ETH driver switched to PHY GPIO reset performed with data defined
in DTS.
For the HSC|DDC boards the GPIO reset signal is active low and hence the
wrong DTS description must be changed (otherwise the reset for ETH is not
properly setup).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Activate I2C7 on Alt to allow access to the PMIC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Due to a final resolution not coming up in time for 2019.04 and
following the consensus on the discussion, we'll keep this around
for 2019.04 after all.
This reverts commit 0d968ceb1f.
This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE
Most of time these value are not needed, CONFIG_SF_DEFAULT
with same value is used, so I introduced CONFIG_USE_ENV_SPI_*
to force the associated value for the environment.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Replace CONFIG_ENV_SPI_BASE by the better CONFIG_SYS_SPI_BASE
(it is not the location for environment but the location for U-Boot)
and, as it is the only platform with use this define, remove
it from whitelist.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
An ADATA 16GB Industrial MLC card has so much capacitance on the Vcc
pin that the usual toggling of regulator to power the card off and on
is insufficient. When the card is calibrated into UHS SDR104 mode, it
will remain in that mode across the power cycle and subsequent attempt
to communicate with the card will fail.
The test with this card is to insert it into an SDHI slot and perform
"mmc dev 0 ; mmc dev 0", where the second "mmc dev 0" will fail.
Fix this problem by increasing the off-on delay from 0 to 20 mS.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since commit 27cb7300ff ("Ensure device tree DTS is compiled"),
build succeeds irrespective of the correctness of Makefile.
In fact, you can compile any defconfig without adding any entry in
arch/*/dts/Makefile.
I am going to revert that commit, so device tree must be explicitly
listed in Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Since commit 27cb7300ff ("Ensure device tree DTS is compiled"),
build succeeds irrespective of the correctness of Makefile.
I am going to revert that commit, so wrong code must be fixed.
CONFIG_MCR3000 is not defined anywhere. CONFIG_TARGET_MCR3000 is the
correct one.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit 27cb7300ff ("Ensure device tree DTS is compiled"),
build succeeds irrespective of the correctness of Makefile.
In fact, you can compile any defconfig without adding any entry in
arch/*/dts/Makefile.
As a result, a lot of wrong code have been merged unnoticed.
I am going to revert that commit, and lots of hidden issues have
come to light:
[1] Typos
armada-3720-uDPU.dts, sun8i-a83t-tbs-a711.dts
use the extension ".dts" instead of ".dtb"
[2] DTB is associated to undefined CONFIG option
For example, mx6sllevk_defconfig defines CONFIG_MX6SLL, but
associates its device tree to CONFIG_MX6SL, which is undefined.
[3] Lots of entries are missing
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
[trini: add imx6ul pico dtbs]
Signed-off-by: Tom Rini <trini@konsulko.com>
Commit 1416e2d225 ("armv8: make SPL exception vectors optional") had a
typo in it which effectively disabled exception handling in SPL code always.
Since nobody complained, I guess we may as well disable exception handling
in SPL always by default.
So fix the bug to make the config option effective, but disable exception
handling in SPL by default. This gets us to the same functionality as before
by default, but with much less code included in the binary.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Push the Starting kernel print to the end just before the
dm_remove_devices call.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Enable network interface on clearfog_gt_8k (Baruch)
- Fix dreamplug boot by adding an spi0 alias to the DT (Chris)
- Fix / enhance Marvell ddr3 setup / parameters (Chris)
- Change CONFIG_SYS_MALLOC_F_LEN to 0x2000 on db-88f6820-amc (Chris)
- Enable SPL_FLASH_BAR on db-88f6820-amc (Chris)
- Use correct pcie controller name in Armada-38x dts files (Chris)
- Disable d-cache on Kirkwood platforms as currently needed (Chris)
- Add a more descriptive comment to pci_mvebu.c (Stefan)
- Update Marvell maintainers entry (Stefan)
Prior to commit 93b283d49f ("ARM: CPU: arm926ejs: Consolidate cache
routines to common file") the kirkwood boards didn't have and dcache
support. The network and usb drivers rely on this. Set
CONFIG_SYS_DCACHE_OFF in the Kirkwood specific config.h.
Reported-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
When armada-385.dtsi was sync'd from Linux the name of the node
describing the pcie controller was changed from pcie-controller to pcie.
Some of the boards that include armada-385.dtsi were missed in the
update retaining the old name. This updates the affected boards.
Reported-by: Влад Мао <vlaomao@gmail.com>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The conversion to DM_SPI managed to break accessing the environment on
dreamplug. This is because the environment code relies on being to able
to select the SPI device based on the sequence number. Add an alias so
that the spi0 bus gets sequence number 0.
Reported-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Stefan Roese <sr@denx.de>
Syscon register is required in dts to select correct
PHY interface.
Fix error below:
Net: Failed to get syscon: -2
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Barrier transactions from CCI400 need to be disabled till
the DDR is configured, otherwise it may lead to system hang.
The patch adds workaround to fix the erratum.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
spba-bus has a few nodes under it including the UART1 and
some ESPI buses. In order to use them in SPL, the
u-boot,dm-spl flag needs to be added to the spba-bus@2000000
container.
Signed-off-by: Adam Ford <aford173@gmail.com>
Currently the CPU frequency is incorrectly reported:
CPU: NXP i.MX8QXP RevB A35 at 147228 MHz
Fix this problem by using a direct call to the SCU firmware to
retrieve the Cortex A35 CPU frequency.
With this change applied the CPU frequency is displayed correctly:
CPU: NXP i.MX8QXP RevB A35 at 1200 MHz
Tested-by: Marcelo Macedo <marcelo.macedo@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
Select CONFIG_DM_MMC=y in order to support MMC driver model.
This allows the MMC board related code to be removed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Import the device tree files from kernel 5.0-rc6 in preparation
for driver model conversion.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
This is currently missing and without it the i8254 beeper driver
won't work.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The pc speaker driven by the i8254 is generic enough to deserve
a single dtsi file to be included by boards that use it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
