When building an SPL image, override the link flags so that it uses the
system libraries. This is similar to the way the non-SPL image is built.
Signed-off-by: Simon Glass <sjg@chromium.org>
SPL is expected to load and run U-Boot. This needs to work with sandbox also.
Provide a function to locate the U-Boot image, and another to start it. This
allows SPL to function on sandbox as it does on other archs.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present armv7 will unhappily invalidate a cache region and print an
error message. Make it skip the operation instead, as it does with other
cache operations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Errata i727 is applicable on all OMAP5 and DRA7 variants but enabled only
on OMAP5 ES1.0. So, enable it on all platforms.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This change is to remove a halt at about 200KiB
while sending a large(1MiB) binary to a micro controller using USART1.
USART1 is connected to a PC via an on-board ST-Link debugger
that also functions as a USB-Serial converter.
However, it seems to loss some data occasionally.
So I changed the serial port to USART6 and connected it to the PC using
an FTDI USB-Serial cable, therefore the transmission was successfully
completed.
Signed-off-by: Toshifumi NISHINAGA <tnishinaga.dev@gmail.com>
This patch adds SDRAM support for stm32f746 discovery board.
This patch depends on previous patch.
This patch is based on STM32F4 and emcraft's[1].
[1]: https://github.com/EmcraftSystems/u-boot
Signed-off-by: Toshifumi NISHINAGA <tnishinaga.dev@gmail.com>
This patch adds 200MHz clock configuration for stm32f746 discovery board.
This patch is based on STM32F4 and emcraft's[1].
[1]: https://github.com/EmcraftSystems/u-boot
Signed-off-by: Toshifumi NISHINAGA <tnishinaga.dev@gmail.com>
At present sandbox exits when the 'bootm' command completes, since it is not
actually able to run the OS that is loaded. Normally 'bootm' failure is
considered a fatal error in U-Boot.
However this is annoying for tests, which may want to examine the state
after a test is complete. In any case there is a 'reset' command which can
be used to exit, if required.
Change the behaviour to return normally from the 'bootm' command on sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Teddy Reed <teddy.reed@gmail.com>
For most of architectures in U-Boot, virtual address is straight
mapped to physical address. So, it makes sense to have generic
defines of ioremap and friends in <linux/io.h>.
All of them are just empty and will disappear at compile time, but
they will be helpful to implement drivers which are counterparts of
Linux ones.
I notice MIPS already has its own implementation, so I added a
Kconfig symbol CONFIG_HAVE_ARCH_IOREMAP which MIPS (and maybe
Sandbox as well) can select.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
These defines are valid only when iomem_valid_addr is defined,
but I do not see such defines anywhere. Remove.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, this is only defined in arch/arm/include/asm/types.h,
so move it to include/linux/types.h to make it available for all
architectures.
I defined it with phys_addr_t as Linux does. I needed to surround
the define with #ifdef __KERNEL__ ... #endif to avoid build errors
in tools building. (Host tools should not include <linux/types.h>
in the first place, but this is already messy in U-Boot...)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Modify the SPL build procedure for AM437x high-security (HS) device
variants to create a secure u-boot_HS.img FIT blob that contains U-Boot
and DTB artifacts signed (and optionally encrypted) with a TI-specific
process based on the CONFIG_TI_SECURE_DEVICE config option and the
externally-provided image signing tool.
Also populate the corresponding FIT image post processing call to be
performed during SPL runtime.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Modify the SPL build procedure for AM57xx and DRA7xx high-security (HS)
device variants to create a secure u-boot_HS.img FIT blob that contains
U-Boot and DTB artifacts signed with a TI-specific process based on the
CONFIG_TI_SECURE_DEVICE config option and the externally-provided image
signing tool.
Also populate the corresponding FIT image post processing call to be
performed during SPL runtime.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adds commands so that when a secure device is in use and the SPL is
built to load a FIT image (with combined U-Boot binary and various
DTBs), these components that get fed into the FIT are all processed to
be signed/encrypted/etc. as per the operations performed by the
secure-binary-image.sh script of the TI SECDEV package. Furthermore,
perform minor comments cleanup to make better use of the available
space.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adds an API that verifies a signature attached to an image (binary
blob). This API is basically a entry to a secure ROM service provided by
the device and accessed via an SMC call, using a particular calling
convention.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adds a generic C-callable API for making secure ROM calls on OMAP and
OMAP-compatible devices. This API provides the important function of
flushing the ROM call arguments to memory from the cache, so that the
secure world will have a coherent view of those arguments. Then is
simply calls the omap_smc_sec routine.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add an interface for calling secure ROM APIs across a range of OMAP and
OMAP compatible high-security (HS) device variants. While at it, also
perform minor cleanup/alignment without any change in functionality.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adds missing flush_dcache_range and invalidate_dcache_range dummy
(empty) placeholder functions to the #else portion of the #ifndef
CONFIG_SYS_DCACHE_OFF, where full implementations of these functions
are defined.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are two enable methods supported by ARM64 Linux; psci and
spin-table. The latter is simpler and helpful for quick SoC bring
up. My main motivation for this patch is to improve the spin-table
support, which allows us to boot an ARMv8 system without the ARM
Trusted Firmware.
Currently, we have multi-entry code in arch/arm/cpu/armv8/start.S
and the spin-table is supported in a really ad-hoc way, and I see
some problems:
- We must hard-code CPU_RELEASE_ADDR so that it matches the
"cpu-release-addr" property in the DT that comes from the
kernel tree.
- The Documentation/arm64/booting.txt in Linux requires that
the release address must be zero-initialized, but it is not
cared by the common code in U-Boot. We must do it in a board
function.
- There is no systematic way to protect the spin-table code from
the kernel. We are supposed to do it in a board specific manner,
but it is difficult to predict where the spin-table code will be
located after the relocation. So, it also makes difficult to
hard-code /memreserve/ in the DT of the kernel.
So, here is a patch to solve those problems; the DT is run-time
modified to reserve the spin-table code (+ cpu-release-addr).
Also, the "cpu-release-addr" property is set to an appropriate
address after the relocation, which means we no longer need the
hard-coded CPU_RELEASE_ADDR.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Upon further review this breaks most other platforms as we need to check
what core we're running on before touching it at all.
This reverts commit d73718f323.
Signed-off-by: Tom Rini <trini@konsulko.com>
if we build for an i.mx6 (d)ual(l)ite CONFIC_MX6DL we shall use
MX6DL_PAD instead the common MX6_PAD.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
MX7_SEC is an existing configuration option that allows booting the
kernel in secure mode.
Place this option in Kconfig, so that boards can select this option
in their defconfig files.
Selecting this option is necessary when booting a kernel provided by
NXP, such as 3.14_GA and 4.1.15_GA.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Michael Trimarchi <michael@amarulasolutions.com>
Custom Board based on MX6 Dual, 1GB RAM and eMMC.
There are two variants of the board with and without
PCIe (ZC5202 and ZC5601).
Signed-off-by: Stefano Babic <sbabic@denx.de>
spl_boot_mode() returned MMCSD_MODE_RAW on MMC if CONFIG_SPL_EXT_SUPPORT
was configured. EXTFS is the default filesystem selected in imx6_spl.h
and the function should return MMCSD_MODE_FS instead.
Fix this and return MMCSD_MODE_FS instead in such cases.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
CC: Stefano Babic <sbabic@denx.de>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Fabio Estevam <Fabio.Estevam@freescale.com>
With the change to set up pinctrl after relocation, link fails to boot. Add
a special case in the link code to handle this.
Fixes: d8906c1f (x86: Probe pinctrl driver in cpu_init_r())
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add support for Advantech SOM-DB5800 with the SOM-6867 installed.
This is very similar to conga-qeval20-qa3-e3845 in that there is a
reference carrier board (SOM-DB5800) with a Baytrail based SoM (SOM-6867)
installed.
Currently supported:
- 2x UART (From ITE EC on SOM-6867) routed to COM3/4 connectors on
SOM-DB5800.
- 4x USB 2.0 (EHCI)
- Video
- SATA
- Ethernet
- PCIe
- Realtek ALC892 HD Audio
Pad configuration for HDA_RSTB, HDA_SYNC, HDA_CLK, HDA_SDO
HDA_SDI0 is set in DT to enable HD Audio codec.
Pin defaults for codec pin complexs are not changed.
Not supported:
- Winbond Super I/O (Must be disabled with jumpers on SOM-DB8500)
- USB 3.0 (XHCI)
- TPM
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If global NVS says internal UART is not enabled, hide it in the ASL
code so that OS won't see it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that platform-specific ACPI global NVS is added, pack it into
ACPI table and get its address fixed up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This introduces quark-specific ACPI global NVS structure, defined in
both C header file and ASL file.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This introduces baytrail-specific ACPI global NVS structure, defined in
both C header file and ASL file.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For any FSP-enabled boards that want to enable debug UART support,
setup_internal_uart() will be called, but this API is only available
on BayTrail platform. Change to wrap it with CONFIG_INTERNAL_UART.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are quite a number of BayTrail boards that uses an external
SuperIO chipset to provide the legacy UART. For such cases, it's
better to have a Kconfig option to enable the internal UART.
So far BayleyBay and MinnowMax boards are using internal UART as
the U-Boot console, enable this on these two boards.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This function have maintained for supporting Non-FDT.
Now, Almost all SoC are changed to fdt style.
So there are no that this function is called anywhere.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
It's correct to use '/' as prefix for aliases nodes.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
We have drivers for several more devices now, so drop the strings which are
no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Define a platform data structure for the MPC85XX GPIO driver to allow
use of the driver without device tree. Users should define the GPIO
blocks for their platform like this:
struct mpc85xx_gpio_plat gpio_blocks[] = {
{
.addr = 0x130000,
.ngpios = 32,
},
{
.addr = 0x131000,
.ngpios = 32,
},
};
U_BOOT_DEVICES(my_platform_gpios) = {
{ "gpio_mpc85xx", &gpio_blocks[0] },
{ "gpio_mpc85xx", &gpio_blocks[1] },
};
This is intended to build upon the recent submission of the base
MPC85XX driver from Mario Six. We need to use that new driver
without dts support and this patch gives us that flexibility.
This has been tested on a Freescale T2080 CPU, although only the first
GPIO block.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Reviewed-by: Mario Six <mario.six@gdsys.cc>
Tested-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Simon Glass <sjg@chromium.org>
Rockchip uses driver model for all subsystems. Specify this in the arm
Kconfig rather than as defaults in the Rockchip Kconfig. This means that
boards cannot turn these options off, which seems correct.
Signed-off-by: Simon Glass <sjg@chromium.org>
According to Data Manual(SPRS915P) of AM57x, TI QSPI controller on
DRA74(rev 1.1+)/DRA72 EVM can support up to 64MHz in MODE-0, whereas
MODE-3 is limited to 48MHz. Hence, switch to MODE-0 for better
throughput.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
K2G SoC has a Cadence QSPI controller to communicate with NOR flash
devices. Add DT nodes to support the same.
Also, K2G EVM has a s25fl512s flash connect to QSPI bus at CS 0. Add nor
flash slave node for the same.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
K2G SoC has 4 SPI instances that are compatible with davinci_spi
controller(present on previous generation of Keystone2 devices). Add DT
nodes for the same. K2G EVM has a N25Q128A13 SPI NOR flash connected on
SPI-1. Add DT bindings for the same.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Now that davinci_spi driver has been converted to DM framework, enable
the same in DT. Also add "spi-flash" as compatible property to
n25q128a11 node as it is required for flash device to be probed in
U-Boot.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Now that davinci_spi driver has been converted to DM framework, enable
the same in DT. Also add "spi-flash" as compatible property to
n25q128a11 node as it is required for flash device to be probed in
U-Boot.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Now that davinci_spi driver has been converted to DM framework, enable
the same in DT. Also add "spi-flash" as compatible property to
n25q128a11 node as it is required for flash device to be probed in
U-Boot.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add aliases for SPI nodes in order for it to be probed by the DM
framework.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
For A53, data coherency is enabled only when the CPUECTLR.SMPEN bit is
set. The SMPEN bit should be set before enabling the data cache.
If not enabled, the cache is not coherent with other cores and
data corruption could occur.
For A57/A72, SMPEN bit enables the processor to receive instruction
cache and TLB maintenance operations broadcast from other processors
in the cluster. This bit should be set before enabling the caches and
MMU, or performing any cache and TLB maintenance operations.
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit e677724 (arm: Fix setjmp) added code to fix compilation of the setjmp
code path with thumv1. Unfortunately it missed a constraint that the adr
instruction can only refer to 4 byte aligned offsets.
So this patch adds the required alignment hooks to make compilation
work again even when setjmp doesn't happen to be 4 byte aligned.
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Tom Rini <trini@konsulko.com>
We have standard drivers for panels and backlights which can do most of the
work for us. Move the tegra20 LCD driver over to use those instead of custom
code.
This patch includes device tree changes for the nvidia boards. I have only
been able to test seaboard. If this patch is applied, these boards will
also need to be synced with the kernel, and updated to use display-timings:
- colibri
- medcom-wide
- paz00
- tec
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Sync everything except the display panel, which will come in a future patch.
One USB port is left disabled since we don't want to support it in U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The errata command is useless in SPL, so don't build it. This fixes
multiple build failures on PowerPC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: York Sun <york.sun@nxp.com>
Fixes: 92623672f9 ("fsl: usb: make errata function common for PPC and ARM")
Currently on attempt to use global_data.h in an assembly file following
will happen:
-------------------->8-----------------
./arch/arc/include/asm/global_data.h: Assembler messages:
./arch/arc/include/asm/global_data.h:11: Error: bad instruction 'struct arch_global_data{'
./arch/arc/include/asm/global_data.h:12: Error: junk at end of line, first unrecognized character is `}'
scripts/Makefile.build:316: recipe for target 'arch/arc/lib/start.o' failed
-------------------->8-----------------
In this change we disable struct arch_global_data in ASM which fixes
the issue above.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Newer ARC toolchains don't support "-marchs" option any longer.
Instead "-mcpu=archs" should be used. What's also important older
toiolchains that support ARC HS cores will also happily accept
"-mcpu=archs" so that's a very safe move.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
The Parrot Board is an evaluation board with an Allwinner R16 (assumed
to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host
and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2
controllable buttons, an LVDS port with separated backlight and
capacitive touch panel ports, an audio/microphone jack, a camera CSI
port, 2 sets of 22 GPIOs and an accelerometer.
The DTS file is identical to the one submitted to the upstream kernel.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Commit b19236fd1 ("sunxi: Increase SPL header size to 64 bytes to avoid
code corruption") Added defines for MMC0 and SPI as boot identification.
After verifying on an OLinuXino Lime2 with NAND and eMMC, the expected
values have been confirmed and added to spl.h
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
I will carry this work-around until it is cared in the kernel.
This looks up the AIDET node and sets up a register to handle
active low interrupt signals.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The AIDET (ARM Interrupt Detector Add-on Circuit) is a kind of
syscon block related with the interrupt controller.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
There is a dummy pch driver in the coreboot directory. This causes
drivers of its children fail to function due to empty ops. Remove
the whole file since it is no longer needed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently layescape SoCs are not using cpu nodes. So removing
them in favour of compatibly with similar SoCs that
have different cores like LS2080A and LS2088A.
This has been tested on LS2080AQDS, LS1043ARDB, LS1012ARDB.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Freescale ARMv8 SoC name ends with "A" to represent ARM SoCs.
like LS2080A, LS1043A, LS1012A.
So append "A" to SoC names.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
add DM and DTS support for the at91 based siemens
boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
Add this files from Linux v4.6-rc5
66b8a424d: [workqueue: fix ghost PENDING flag while doing MQ IO]
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Andreas Bießmann <andreas@biessmann.org>
Since the spl_boot_mode() is now passed the boot device to boot from,
make use of it instead of inquiring for the boot device again. This
allows board_boot_order() to function correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
The SPL code already knows which boot device it calls the spl_boot_mode()
on, so pass that information into the function. This allows the code of
spl_boot_mode() avoid invoking spl_boot_device() again, but it also lets
board_boot_order() correctly alter the behavior of the boot process.
The later one is important, since in certain cases, it is desired that
spl_boot_device() return value be overriden using board_boot_order().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[add newly introduced zynq variant]
Signed-aff-by: Andreas Bießmann <andreas@biessmann.org>
The handling of the "usage counter" is incorrect, and the clock should
only be disabled when transitioning from 1 to 0.
Reported-by: Chris Brand <chris.brand@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
The Kona Peripheral Slave CCU has 4 policy mask registers, not 8.
Signed-off-by: Chris Brand <chris.brand@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Match the #ifdef ... #endif and the code,
ret = do_something();
if (ret)
return ret;
This will make it easier to add more #ifdef'ed code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
gic_kick_secondary_cpus can directly return to the caller of
smp_kick_all_cpus. We do not have to use x29 register here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
s/hardkernel/amlogic/ to have a single place for all the amlogic-based
boards.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
The register CLKCNCSR controls the frequency of all cores in the same
cluster.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
DISTRO_DEFAULTS is intended to mirror / replace
include/config_distro_defaults.h.
The intend is for boards which include this file to select this from
their Kconfig files and when moving setting to Kconfig which are #define-ed
in config_distro_defaults.h to select this from DISTRO_DEFAULTS so that
boards which have selected DISTRO_DEFAULTS will keep the same configuration
as before without needing any defconfig file changes.
The initial list of selected things matches all settings recently removed
from config_distro_defaults.h because they have been converted to Kconfig,
with the exception of CMD_ELF and CMD_NET, which have a default of y, if
the default of these ever changes they should be selected by DISTRO_DEFAULTS
too.
For testing and example purposes this commit also converts ARCH_SUNXI
to use DISTRO_DEFAULT instead of selecting everything it needs itself.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
To make the PSCI backend more maintainable and easier to port to newer
SoCs, rewrite the current PSCI implementation in C.
Some inline assembly bits are required to access coprocessor registers.
PSCI stack setup is the only part left completely in assembly. In theory
this part could be split out of psci_arch_init into a separate common
function, and psci_arch_init could be completely in C.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Instead of hardcoding the GIC addresses in the PSCI implementation,
provide a base address in the cpu header.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
CPUCFG has an unlisted debug control register, which is used to disable
external debug access.
Also, sun7i secondary core power controls are in CPUCFG, as there's no
separate PRCM block.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Instead of listing individual registers for controls to each processor
core, list them as an array of registers. This makes accessing controls
by core index easier.
Also rename "cpucfg_sun6i.h" (which was unused anyway) to the more generic
"cpucfg.h", and add packed attribute to struct sunxi_cpucfg.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
cpucfg_sun6i.h includes a register definition for the CPUCFG register
block. The types used are u32 and u8, which are defined in linux/types.h.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
struct sunxi_prcm_reg is a representation of the PRCM registers. Add
the packed attribute to prevent the compiler from doing funny things.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Use SUNXI_CPUCFG_BASE across all families. This makes writing common
PSCI code easier.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The PSCI implementation expects at most 2 pages worth of space reserved
at the end of the secure section for its stacks. If PSCI is relocated to
secure SRAM, then everything is fine. If no secure SRAM is available,
and PSCI remains in main memory, the reserved memory space doesn't cover
the space used by the stack.
If one accesses PSCI after Linux has fully booted, the memory that should
have been reserved for the PSCI stacks may have been used by the kernel
or userspace, and would be corrupted. Observed after effects include the
system hanging or telinit core dumping when trying to reboot. It seems
the init process gets hit the most on my test bed.
This fix allocates the space used by the PSCI stacks in the secure
section by skipping pages in the linker script, but only when there is
no secure SRAM, to avoid bloating the binary.
This fix is only a stop gap. It would be better to rework the stack
allocation mechanism, maybe with proper usage of CONFIG_ macros and an
explicit symbol.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Some common PSCI functions are written in assembly, but it should be
possible to use them from C code.
Add function declarations for C code to consume.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
For psci_get_cpu_stack_top() to be usable in C code, it must adhere to
the ARM calling conventions. Since it could be called when the stack
is still unavailable, and the entry code to linux also expects r1 and
r2 to remain unchanged, stick to r0 and r3.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The inet86dz board is a board used in 7" tablets from various oems.
These tablets are a23 based 7" tablets featuring a 1024x600 LCD,
512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen,
micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector
which doubles as charging port.
The dts file this commit adds is identical to the one submitted to
the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Polaroid MID2407PXE03 is an a23 based 7" tablet based on a M86_MB V2.0
PCB, featuring a 800x480 LCD, 512MB RAM, 4G NAND, esp8089 wifi, gsl1680
touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg
connector which doubles as charging port.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This gives us a bit more breathing room wrt our SPL size.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
The following changes are made to the clock API:
* The concept of "clocks" and "peripheral clocks" are unified; each clock
provider now implements a single set of clocks. This provides a simpler
conceptual interface to clients, and better aligns with device tree
clock bindings.
* Clocks are now identified with a single "struct clk", rather than
requiring clients to store the clock provider device and clock identity
values separately. For simple clock consumers, this isolates clients
from internal details of the clock API.
* clk.h is split so it only contains the client/consumer API, whereas
clk-uclass.h contains the provider API. This aligns with the recently
added reset and mailbox APIs.
* clk_ops .of_xlate(), .request(), and .free() are added so providers
can customize these operations if needed. This also aligns with the
recently added reset and mailbox APIs.
* clk_disable() is added.
* All users of the current clock APIs are updated.
* Sandbox clock tests are updated to exercise clock lookup via DT, and
clock enable/disable.
* rkclk_get_clk() is removed and replaced with standard APIs.
Buildman shows no clock-related errors for any board for which buildman
can download a toolchain.
test/py passes for sandbox (which invokes the dm clk test amongst
others).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
This adds a sandbox reset implementation (provider), a test client
device, instantiates them both from Sandbox's DT, and adds a DM test
that excercises everything.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tegra186's HSP module implements doorbells, mailboxes, semaphores, and
shared interrupts. This patch provides a driver for HSP, and hooks it
into the mailbox API. Currently, only doorbells are supported.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
The documentation of parameters in arch/sandbox/include/asm/gpio.h is
either missing or faulty.
This patch corrects the documentation.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Simon Glass <sjg@chromium.org>
The DRAM PHY layer on PH1-LD20 is able to calibrate PHY parameters
periodically. This compensates for the voltage and temperature
deviation and improves the PHY parameter adjustment. Instead, it
requires 64 byte scratch memory in each DRAM channel for the dynamic
training. The memory regions must be reserved in DT before jumping
to the kernel.
The scratch area can be anywhere in each DRAM channel, but the DRAM
init code in SPL currently assigns it at the end of each channel.
So, it makes sense to reserve the regions on run-time by U-Boot
instead of statically embedding it in the DT in Linux. Anyway,
a boot-loader should know much more about memory initialization
than the kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This will make it easier to select config options specific to
particular ARM processor generation.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The setjmp/longjmp implementation did not work on thumb1 implementations
because it used instruction encodings that don't exist on thumb1 yet.
This patch limits itself to thumb1 instruction set for 32bit arm and
removes a superfluous printf along the way.
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch is doing the following:
1. Implementing the errata for LS2080.
2. Adding fixup for fdt for LS2080.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
This errata a008751 is applied on Soc specific file currently.This will be
moved to a file where all the errata implementation will take place for usb
for fsl. This patch removes the errata workaround from soc specific file
for LS2080.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Adds get_svr and IS_SVR_REV helpers for ARMv8 platforms,
similar to PPC and ARMv7.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
board/am57xx supports all boards based on am57xx. Rename the taget
as TARGET_AM57XX_EVM.
Fixes: 74cc8b097d ("board: ti: beagle_x15: Rename to indicate support for TI am57xx evms")
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add initial support for NXP's S32V234 SoC and S32V234EVB board.
The S32V230 family is designed to support computation-intensive applications
for image processing. The S32V234, as part of the S32V230 family, is a
high-performance automotive processor designed to support safe
computation-intensive applications in the area of vision and sensor fusion.
Code originally writen by:
Original-signed-off-by: Stoica Cosmin-Stefan <cosminstefan.stoica@freescale.com>
Original-signed-off-by: Mihaela Martinas <Mihaela.Martinas@freescale.com>
Original-signed-off-by: Eddy Petrișor <eddy.petrisor@gmail.com>
Signed-off-by: Eddy Petrișor <eddy.petrisor@nxp.com>
Memory barriers are proven to be a requirement for both compiler and
real hardware to properly serialize access to critical data.
For example if CPU or data bus it uses may do reordering of data
accesses absence of memory barriers might easily lead to very subtle and
hard to debug data corruptions.
This implementation was heavily borrowed from up to date Linux kernel.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
According to ARC HS databook it is required to flush and disable
caches prior programming IOC registers. Otherwise ongoing coherent
memory operations may not observe the coherency protocols as
expected.
But since in ARC HS v2.1 there's no way to disable SLC (AKA L2 cache)
we're doing our best flushing and invalidating it.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
invalidate_dcache_all() could be used in different use-cases
and what is especially important most of those cases won't be
related to DMAed data to or from peripherals, i.e. we'll be doing
invalidation of data used purely by CPU cores.
Given that IOC engine only snoops data that goes through DMA
we need to care ourselves about data used only by CPU cores
and so remove dependency on IOC from invalidate_dcache_all()
and always do real invalidation.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Add missing parenthesis around the variable into the macro.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Extend the boot device autodetection from SAMA5D2 only to the entire
SAMA5Dx family of microcontrollers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[minor compile fix for SAMA5D2]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
This board is based on Snapper 9G45 which has an Atmel AT91SAM9G45 chip and
128MB of SDRAM. It includes a small LCD, 2xUSB host, SD card, Ethernet and
two UARTs.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[apply CONFIG_BOOTDELAY transition]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
Add these definitions so that GPIOs can be used with driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-on: smartweb, corvus, taurus, axm
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Add register definitions for the AT91 RTC so that this can potentially be
used in U-Boot.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
At present CONFIG_SKIP_LOWLEVEL_INIT prevents U-Boot from calling
lowlevel_init(). This means that the instruction cache is not enabled and
the board runs very slowly.
What is really needed in many cases is to skip the call to lowlevel_init()
but still perform CP15 init. Add an option to handle this.
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-on: smartweb, corvus, taurus, axm
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
This is available on AT91SAM9G45. Add the peripheral address and flag
definitions.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Currently omap_vcores which holds pmic data is being assigned based
on the SoC type. PMIC is not a part of SoC. It is logical to
to assign omap_vcores based on board type. Hence over ride the
vcores_init function and assign omap_vcores based on the board type.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
At present pinctrl driver gets probed in ich6_gpio driver's probe
routine, which has two issues:
- Pin's PADs only gets configured when GPIO driver is probed, which
is not done by default. This leaves the board in a partially
functional state as we must initialize PADs correctly to get
perepherals fully working.
- The probe routine of pinctrl driver is called multiple times, as
normally there are multiple GPIO controllers. It should really
be called just once.
Move the call to syscon_get_by_driver_data() from ich6_gpio driver
to cpu_init_r().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
As of today, the latest version FSP (gold4) for BayTrail misses the
PAD configuration of the SD controller's Card Detect signal. The
default PAD value for the CD pin sets the pin to work in GPIO mode,
which causes card detect status cannot be reflected by the Present
State register in the SD controller (bit 16 & bit 18 are always zero).
Add a configuration for this pin in the pinctrl node.
Note I've checked the PAD configuration for all the pins in all the
3 controllers (eMMC/SDIO/SD). Only this SDMMC3_CD_B pin does not get
initialized to correct mode by FSP. With fsp,emmc-boot-mode set to
2 (eMMC 4.1), eMMC pins are initialized to func 1, but if we set
fsp,emmc-boot-mode to 1 (auto), those pins are initialized to func 3
which is correct according to datasheet.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present all BayTrail boards configure fsp,emmc-boot-mode to 2,
which means "eMMC 4.1" per FSP documentation. However, eMMC 4.1
only shows up on some early stepping silicon of BayTrail SoC.
Newer stepping SoC integrates an eMMC 4.5 controller. Intel FSP
provides a config option fsp,emmc-boot-mode which tells FSP which
eMMC controller it initializes. Instead of hardcoded to 2, now
we change it to 1 which means "auto".
With this change, MinnowMax board (with a D0 stepping BayTrail SoC)
can see the eMMC 4.5 controller at PCI address 00.17.00 via U-Boot
'pci' command.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Without a 'reg' property, pinctrl driver probe routine fails in
its pre_probe() with a return value of -EINVAL.
Add 'reg' property for all BayTrail boards. Note for BayleyBay,
the pinctrl node is newly added.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
An accumulated length was incorrectly added to current each pass
through the loop. On system with more than 2 cores this caused a
corrupt MADT to be generated.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds QSPI boot support for LS2080AQDS board.
The QSPI boot image need to be programmed into the QSPI flash
first. Then we can switch to booting from QSPI memory space.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Environment variable mcinitcmd is defined to initiate MC and DPL
deployment from the location where it is stored (NOR, NAND, SD, SATA,
USB) during booting. If this variable is not defined then macro
MC_BOOT_ENV_VAR will be null and MC will not be booted and DPL will
not be applied during U-boot booting.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The SP805-WDT module on LS2080A requires configuration of PMU's
PCTBENR register to enable watchdog counter decrement and reset
signal generation. The watchdog clock needs to be enabled first.
Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Currently the AHB1 clock speed is configured as 200MHz by
the SPL, but this causes a subtle and hard to reproduce data
corruption in SRAM C (for example, this can't be easily
detected with a trivial memset/memcmp test).
For what it's worth, the Allwinner's BSP configures AHB1
as 200MHz, as can be verified by running the devmem2 tool
in the system running the Allwinner's kernel 3.10.x:
0x1C20028: PLL_PERIPH0_CTRL_REG = 0x90041811
0x1C20054: AHB1_APB1_CFG_REG = 0x3180
0x1C20058: APB2_CFG_REG = 0x1000000
0x1C2005C: AHB2_CFG_REG = 0x1
However the FEL mode uses more conservative settings (100MHz
for AHB1):
0x1C20028: PLL_PERIPH0_CTRL_REG = 0x90041811
0x1C20054: AHB1_APB1_CFG_REG = 0x3190
0x1C20058: APB2_CFG_REG = 0x1000000
0x1C2005C: AHB2_CFG_REG = 0x0
It is yet to be confirmed whether faster AHB1/AHB2 clock settings
can be used safely if we initialize the AXP803 PMIC instead of
using reset defaults. But in order to resolve the data corruption
problem right now, it's best to downclock AHB1 to a safe level.
Note that this issue only affects the SPL, which is not fully
supported on Allwinner A64 yet and it should not affect the boot0
usage (unless somebody can confirm SRAM C corruption with the
boot0 too).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
For consistency with the other cache-related Kconfig entries & the
values actually set by boards, make CONFIG_SYS_DCACHE_LINE_SIZE an int
entry instead of a hex entry.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 372286217f ("MIPS: Split I & D cache line size config")
Commit fb64cda579 ("MIPS: Abstract cache op loops with a macro")
accidentally modified invalidate_dcache_range to operate on the L1
Icache instead of the Dcache. Fix the cache op used to operate on the
Dcache.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: fb64cda579 ("MIPS: Abstract cache op loops with a macro")
In the draco CPU board family, etamin is a new variant
with bigger flash and more RAM. Due to new flash that
uses larger pages (4K) some changes are necessary because
it impacts the MTD partition layout and the ubi mount
parameters.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
[trini: Move BOOTDELAY into defconfig, just always be 3 now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable Spread Spectrum for the MPU by calculating the required
values and setting the registers accordingly.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
add missing CM_CLKMODE_DPLL_SSC_ACK_MASK,
CM_CLKMODE_DPLL_SSC_DOWNSPREAD_MASK and
CM_CLKMODE_DPLL_SSC_TYPE_MASK
defines. Used for enabling spread spectrum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
I noticed secondary CPUs sometimes fail to wake up, and the root
cause is that the sev instruction wakes up slave CPUs before the
preceding the register write is observed by them.
The read-back of the accessed register does not guarantee the order.
In order to ensure the order between the register write and the sev
instruction, a dsb instruction should be executed prior to the sev.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This code auto-detects the best-match FDT file name, but it should
respect the user's choice if "fdt_file" environment is found in a
saved set of environments.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This function is shared between PH1-LD11 and PH1-LD20. The difference
is the boot-mode latch for the USB boot mode.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Boot ROM on PH1-LD11/LD20 exports built-in APIs to load images
from an eMMC device. They are useful to reduce the memory footprint
of SPL, rather than compiling the whole MMC framework.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Just sort the board entries, no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
This adds support for IS1 board. Pretty usual socfpga board,
256MB of RAM, does not have MMC, two SPI chips, one ethernet port, two
additional ethernet ports connected to the FPGA.
Signed-off-by: Pavel Machek <pavel@denx.de>
Both comments look like being copy & paste errors.
Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com>
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Some SPL loaders (like Allwinner's boot0, and Broadcom's boot0)
require a header before the actual U-Boot binary to both check its
validity and to find other data to load. Sometimes this header may
only be a few bytes of information, and sometimes this might simply
be space that needs to be reserved for a post-processing tool.
Introduce a config option to allow assembler preprocessor commands
to be inserted into the code at the appropriate location; typical
assembler preprocessor commands might be:
.space 1000
.word 0x12345678
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Commit Notes:
Please note that the current code:
start.S (arm64) and
vectors.S (arm)
already jumps over some portion of data already, so this option basically
just increases the size of this region (and the resulting binary).
For use with Allwinner's boot0 blob there is a tool called boot0img[1],
which fills the header to allow booting A64 based boards.
For the Pine64 we need a 1536 byte header (including the branch
instruction) at the moment, so we add this to the defconfig.
[1] https://github.com/apritzel/pine64/tree/master/tools
END
Reviewed-by: Tom Rini <trini@konsulko.com>
To quit an EFI application we will need logic to jump to the caller
of a function without returning from the function we called into,
so we need setjmp/longjmp functionality.
This patch introduces a trivial implementation of these that I
verified works on armv7, thumb2 and aarch64.
Signed-off-by: Alexander Graf <agraf@suse.de>
Add some tests for the new open drain setting feature of the GPIO
uclass, and extend the capabilities of the sandbox GPIO driver
accordingly.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds a driver for the built-in GPIO controller of the MPC85XX
SoC (probably supporting other PowerQUICC III SoCs as well).
Each GPIO bank is identified by its own entry in the device tree, i.e.
gpio-controller@fc00 {
#gpio-cells = <2>;
compatible = "fsl,pq3-gpio";
reg = <0xfc00 0x100>
}
By default, each bank is assumed to have 32 GPIOs, but the ngpios
setting is honored, so the number of GPIOs for each bank in configurable
to match the actual GPIO count of the SoC (e.g. the 32/32/23 banks of
the P1022 SoC).
The usual functions of GPIO drivers (setting input/output mode and output
value setting) are supported.
The driver has been tested on MPC85XX, but it is likely that other
PowerQUICC III devices will work as well.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Replace a number of array length calculations with the ARRAY_SIZE()
macro, for clarity.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: York Sun <york.sun@nxp.com>
QorIQ LS1012A FREEDOM (LS1012AFRDM) is a high-performance
development platform, with a complete debugging environment.
The LS1012AFRDM board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QorIQ LS1012A Development System (LS1012AQDS) is a high-performance
development platform, with a complete debugging environment.
The LS1012AQDS board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The QorIQ LS1012A processor, optimized for battery-backed or
USB-powered, integrates a single ARM Cortex-A53 core with a hardware
packet forwarding engine and high-speed interfaces to deliver
line-rate networking performance.
This patch add support of LS1012A SoC along with
- Update platform & DDR clock read logic as per SVR
- Define MMDC controller register set.
- Update LUT base address for PCIe
- Avoid L3 platform cache compilation
- Update USB address, errata
- SerDes table
- Added CSU IDs for SDHC2, SAI-1 to SAI-4
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Makarand Pawagi <makarand.pawagi@mindspeed.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
SoC overviews are getting repeated across board folders.
So, Organize SoC overview at common location i.e. fsl-layerscape/doc
Also move README.lsch2 and README.lsch3 in same folder.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch2_speed.c: In function
‘get_sys_info’:
arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch2_speed.c:29:6: warning:
unused variable ‘rcw_tmp’ [-Wunused-variable]
u32 rcw_tmp;
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Other than LS1043A, LS1012A also Chassis Gen2 Architecture compliant.
So Avoid LS1043A specific defines in arch/arm
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
It is not mandatory for Layerscape SoCs to have SMMU. SoCs like
LS1012A are layerscape SoC without SMMU IP.
So put SMMU configuration code under SMMU_BASE.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
With the existing code, function symbols are defined in .text, and the
body is defined in .text.xxx. This causes (at least some version of) the
linker not to emit the function body into the final binary, since it's
part of a different section to the symbols being referenced. This of
course causes a wide variety of failures.
This change moves the push/pop-section directives before the function
symbols, and after any relate ENDPROC macro invocations, so that symbols
and bodies are all in the "pushed" sections, and thus the function bodies
are emitted into the binary.
This solves (at least) the boot problems currently seen on Tegra systems
that use SPL (i.e. all ARMv7 Tegras).
Fixes: 13b0a91a6d ("arm: lib: Split asm symbols into different .text subsections")
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
BOOTCFG_RSTMUX8 register controls the reset mux associated with the ARM.
Timer5(dedicated to ARM) when used as WatchDog timer, the events it
generates are routed to the above mux.
Following are the 3 events that can controlled bt the reset mux:
- Device Reset
- An interrupt to the ARM_GIC
- An interrupt to the ARM_GIC followed by a device reset.
Right now to give a default watchdog behaviour "Device reset" is
being selected.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
The pmic registers for variants of am57xx boards are different
hence we need to assign them carefully based on the board type.
Add a function to assign omap_vcores after the board detection.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Define specific macros for the voltage values for all voltage
domains for all applicable OPPs - OPP_NOM, OPP_OD and OPP_HIGH.
No separate macros are defined for VD_MPU and VD_CORE at OPP_OD
and OPP_HIGH as these use the same values as OPP_NOM.
The current macros will be used as common macros that can be
redefined appropriately based on a selected OPP configuration
at build time.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The voltage values for each voltage domain at an OPP is identical
across all the SoCs in the DRA7 family. The current code defines
one set of macros for DRA75x/DRA74x SoCs and another set for DRA72x
macros. Consolidate both these sets into a single set.
This is done so as to minimize the number of macros used when voltage
values will be added for other OPPs as well.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Define a set of common macros for the efuse register offsets
(different for each OPP) that are used to get the AVS Class 0
voltage values and ABB configuration values. Assign these
common macros to the register offsets for OPP_NOM by default
for all voltage domains. These common macros can then be
redefined properly to point to the OPP specific efuse register
offset based on the desired OPP to program a specific voltage
domain.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The current OPP_NOM voltage values defined for the MPU and CORE
voltage domains are based on the initial DRA75x_74x_SR1.1_DM data
manual. As per this DM, the PMIC boot voltage can be set to either
1.10V or 1.15V for VD_MPU, and either 1.06V or 1.15V for VD_CORE.
While the current values are correct, the latter set of values
are the values that are common across all DRA75x, DRA72x SoCs and
for all current Silicon revisions. So, update both the MPU and CORE
OPP_NOM voltages to 1.15V.
The macros are also slightly reorganized so that both the MPU and
CORE voltage domain values are defined together.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
CONFIG_USB_XHCI_OMAP is enabled for host mode independent of CONFIG_USB_DWC3
which is meant for gadget mode only. We need enable/disbale_usb_clocks() for
host mode as well so provide for it.
Fixes: 09cc14f4bc ("ARM: AM43xx: Add functions to enable and disable USB clocks"
Signed-off-by: Roger Quadros <rogerq@ti.com>
Split each symbol in lib1funcs into different .text.foo section instead
of placing all of them into plain .text . This allows the linker to collect
and discard unused assembler symbols.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Import functions into lib1funcs.S which are required for Thumb1
build. These functions come from gcc 5.3.1 release.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Import muldi3.S from Linux 4.4.6 , commit 0d1912303e54ed1b2a371be0bba51c384dd57326
on arm32. This file implements __aeabi_lmul and it's alias __muldi3, which
is needed when doing Thumb1 builds.
This patch also defines CONFIG_THUMB2_KERNEL and CONFIG_ARM_ASM_UNIFIED
which is necessary for correct build of these files both in ARM and
Thumb mode, just like Linux does.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Fix the following warning when building for thumb2 target by tweaking the
instruction syntax:
Warning: conditional infixes are deprecated in unified syntax
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Import __do_div64 from Linux 4.4.6 , commit 0d1912303e54ed1b2a371be0bba51c384dd57326
on arm32. This function is for some toolchains, which generate _udivmoddi4()
for 64 bit division.
Since we do not support stack unwinding, instead of importing the whole
asm/unwind.h and all the baggage, this patch defines empty UNWIND() macro.
This patch also defines CONFIG_THUMB2_KERNEL and CONFIG_ARM_ASM_UNIFIED
which is necessary for correct build of these files both in ARM and
Thumb mode, just like Linux does.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This assembler source won't build in Thumb2 mode, so fix it adding
the necessary Thumb2 conditional macros from unified.h .
This patch also defines CONFIG_THUMB2_KERNEL and CONFIG_ARM_ASM_UNIFIED
which is necessary for correct build of these files both in ARM and
Thumb mode, just like Linux does.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Sync the libgcc 32bit division and modulo operations with Linux 4.4.6 ,
commit 0d1912303e54ed1b2a371be0bba51c384dd57326 . The functions in these
four files are present in lib1funcs.S in Linux, so replace these files
with lib1funcs.S from Linux.
Since we do not support stack unwinding, instead of importing the whole
asm/unwind.h and all the baggage, this patch defines empty UNWIND() macro
in lib1funcs.S . Moreover, to make all of the functions available, define
CONFIG_AEABI , which is safe, because U-Boot is always compiled with ARM
EABI.
This patch also defines CONFIG_THUMB2_KERNEL and CONFIG_ARM_ASM_UNIFIED
which is necessary for correct build of these files both in ARM and
Thumb mode, just like Linux does.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Sync the libgcc shift operations with Linux kernel 4.4.6 , commit
0d1912303e54ed1b2a371be0bba51c384dd57326 . Syncing these three
files is easy, as there is almost no change in them, except the
addition of Thumb support.
This patch also defines CONFIG_THUMB2_KERNEL and CONFIG_ARM_ASM_UNIFIED
which is necessary for correct build of these files both in ARM and
Thumb mode, just like Linux does.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Drop the underscore from the filenames of files implementing libgcc
routines. There is no functional change. This change is done to make
sync with Linux kernel easier.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Import unified.h from Linux kernel 4.4.6 , commit
0d1912303e54ed1b2a371be0bba51c384dd57326 . This header file contains
macros used in libgcc functions in Linux kernel on ARM and will be
needed for the libgcc sync.
Since unified.h defines the W(instr) macro, we must drop this from
the macro from memcpy.S , otherwise this triggers a warning about
symbol redefinition. In order to keep the changes to unified.h to
the minimum, tweak arch/arm/lib/Makefile such that it defines the
CONFIG_ARM_ASM_UNIFIED macro, which places .syntax unified into all
of the assembler files. This is mandatory.
Moreover, for Thumb2 build, define CONFIG_THUMB2_KERNEL macro if and
only if Thumb2 build is enabled. This macro is checked by unified.h
and toggles between ARM and Thumb2 variant of the instructions in the
assembler source files.
Finally, this patch defines __LINUX_ARM_ARCH__=N macro based on the
new CONFIG_SYS_ARM_ARCH Kconfig option. This macro selects between
more optimal and more dense codepaths which work on armv5 and newer
and less optimal codepaths which work on armv4 and possible armv3m.
Tegra2 needs the same special handling as it does in arch/arm/Makefile
to cater for the arm720t boot core.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Introduce new helper Kconfig option, which is automatically set to
the version of ARM architecture for which the U-Boot is built. This
is useful when selecting tuning options in the libgcc imported from
Linux kernel.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Select the config option, since this board is ARM64.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
The arm946es is armv5te , so use -march=armv5te instead of armv4t.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Add support for board based on the popular Altera Cyclone V SoC.
This board has the following properties:
- 1 GiB of DRAM
- 1 Gigabit ethernet
- 1 USB gadget port
- 1 USB host port with an on-board hub
- 2 QSPI NORs connected to the Cadence QSPI core
- Multiple I2C EEPROMs and one I2C temperature sensor
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
---
V2: Update the defconfig as per Tom's request
P2771-0000 is a P3310 CPU board married to a P2597 I/O board. The
combination contains SoC, DRAM, eMMC, SD card slot, HDMI, USB micro-B
port, Ethernet, USB3 host port, SATA, PCIe, and two GPIO expansion
headers.
Currently, due to U-Boot's level of support for Tegra186, the only
features supported by U-Boot are the console UART and the on-board eMMC.
Additional features will be added over time.
U-Boot has so far been tested by replacing the kernel image on the device
with a U-Boot binary. It is anticipated that U-Boot will eventually
replace the CCPLEX bootloader binary, as on previous chips. This hasn't
yet been tested.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This adds the bare minimum code to support Tegra186, with UART and eMMC
working.
The empty gpio.h is required because <asm/gpio.h> includes it. A future
cleanup round may be able to solve this for all Tegra generations at once.
mach-tegra/Makefile is adjusted not to compile anything for Tegra186, but
instead to defer everything to mach-tegra/tegra186/Makefile. This allows
the SoC code to pick-and-choose which of the C files in the "common"
mach-tegra/ directory to compile in based on the SoC's needs. Most of the
code is not valid for Tegra186, and this approach removes the need for
mach-tegra/Makefile to contain many SoC-specific ifdefs. This approach
may be applied to all other Tegra SoCs in a future cleanup round.
board186.c is introduced to replace board.c and board2.c. These files
currently contain a slew of SoC- and board-specific code that is not
valid for Tegra186. This approach avoids adding yet more ifdefs to those
files. A future cleanup round may refactor most of board*.c into board-/
SoC-specific functions files thus allowing the top-level functions like
board_init_early_f to be shared again.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra186's MMC controller needs to be explicitly identified. Add another
compatible value for it.
Tegra186 will use an entirely different clock/reset control mechanism to
existing chips, and will use standard clock/reset APIs rather than the
existing Tegra-specific custom APIs. The driver support for that isn't
ready yet, so simply disable all clock/reset usage if compiling for
Tegra186. This must happen at compile time rather than run-time since the
custom APIs won't even be compiled in on Tegra186. In the long term, the
plan would be to convert the existing custom APIs to standard APIs and get
rid of the ifdefs completely.
The system's main eMMC will work without any clock/reset support, since
the firmware will have already initialized the controller in order to
load U-Boot. Hence the driver is useful even in this apparently crippled
state.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Future chips will contain different GPIO HW. This change will enable
future SoC support to select the appropriate GPIO driver for their HW,
in a future-looking fashion, using Kconfig.
TEGRA_GPIO is not simply selected by TEGRA_COMMON (even though all
current Tegra chips used this GPIO HW) to simplify the later addition
of support for Tegra SoCs that use different GPIO HW.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There are currently many places that define the list of all Tegra GPIOs;
the DT binding header and custom Tegra-specific header file gpio.h. Fix
the redundancy by replacing everything with the DT binding header file.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a platform prefix for function name in order to make more readable,
and move it into ath79.h
Signed-off-by: Wills Wang <wills.wang@live.com>
Acked-by: Marek Vasut <marex@denx.de>
The various cache maintenance routines perform a number of loops over
cache lines. Rather than duplicate the code for performing such loops,
abstract it out into a new cache_loop macro which performs an arbitrary
number of cache ops on a range of addresses. This reduces duplication in
the existing L1 cache maintenance code & will allow for not adding
further duplication when introducing L2 cache support.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Allow L1 Icache & L1 Dcache line size to be specified separately, since
there's no architectural mandate that they be the same. The
[id]cache_line_size functions are tidied up to take advantage of the
fact that the Kconfig entries are always present to simply check them
for zero rather than needing to #ifdef on their presence.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
[removed CONFIG_SYS_CACHELINE_SIZE in include/configs/pic32mzdask.h]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Move details of the L1 cache line sizes & total sizes into Kconfig,
defaulting to 0. A new CONFIG_SYS_CACHE_SIZE_AUTO Kconfig entry is
introduced to allow platforms to select auto-detection of cache sizes,
and it defaults to being enabled if none of the cache sizes are set by
the configuration (ie. sizes are all the default 0), and code is
adjusted to #ifdef on that rather than on the definition of the sizes
(which will always be defined even if 0).
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Those wrappers for linker symbols were once used in the MIPS
specific board.c implementation. Since the migration to generic
board.c, those wrappers are dead code and can be removed.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Provide a default linker script for SPL binaries. Start address
and size of text section and BSS section are configurable. All
sections are arranged in a way that only relevant sections are
kept in the code section for maximum size reduction. All other
sections are kept but moved outside the code section to help
with debugging.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Both real Malta boards & emulators that mimic Malta (eg. QEMU) can
support MIPS64 CPUs. Allow MIPS64 builds of U-Boot for such boards,
which enables the user to make use of the whole 64 bit address space.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Use CPHYSADDR to implement the virt_to_phys function for converting from
a virtual to a physical address for MIPS32, much as is already done for
MIPS64. This allows for virt_to_phys to work regardless of whether the
address being translated is in kseg0 or kseg1, unlike the previous
subtraction based approach which only worked for addresses in kseg0.
This allows for drivers to provide an address to virt_to_phys without
needing to manually ensure that kseg1 addresses are converted to
equivalent kseg0 addresses first.
This patch is equivalent to this Linux patch currently waiting to be
reviewed & merged:
https://patchwork.linux-mips.org/patch/12564/
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
So far this is hardcoded to 2, but it should really be read
from the I/O APIC register.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds basic quark platform ASL files. They are intended to be
included in dsdt.asl of any board that is based on this platform.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is a device.h for quark on-chip devices, mainly for definitions
of internal PCI device numbers, but it's not ready to be included by
ASL files. Update to use hex numbers for PCI dev and __ASSEMBLY__.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The irqroute.asl file is already common enough to all x86 platforms.
Platform ASL files need only provide a irqroute.h to describe how
internal PCI devices and PCIe downstream port devices' INTx pins are
routed to which PIRQ pin.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the irqlinks.asl file currently in the BayTrail directory to
a common place to be shared among all x86 platforms. As the PIRQ
routing control programming interface is common to Intel chipsets,
leave the common part in the common file, and move the platform
specific part to the platform files.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For odroid-c2 (arch-meson) for now disable designware eth as meson
now needs to do some harder GPIO work.
Signed-off-by: Tom Rini <trini@konsulko.com>
Conflicts:
lib/efi_loader/efi_disk.c
Modified:
configs/odroid-c2_defconfig
All the output clock parameters of a DPLL needs to be programmed before
locking the DPLL. But it is being configured after locking the DPLL which
could potentially bypass DPLL. So fixing this sequence.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Since 1e6ad55c05 ("armv8/cache: Change cache invalidate and flush
function"), this routine can be used for both cache flushing and
cache invalidation. So, it is better to not include "flush" in
this routine name.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
__asm_dcache_all can directly return to the caller of
__asm_{flush,invalidate}_dcache_all.
We do not have to waste x16 register here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add minimal dts support for AM335x-ICEv2 board
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
The CDCE913 and CDCEL913 devices are modular PLL-based, low cost,
high performance , programmable clock synthesizers. They generate
upto 3 output clocks from a single input frequency. Each output can
be programmed for any clock-frequency.
Adding support for the same.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM335x ICEv2 contains a 2Gbit(128Mx16) of DDR3 SDRAM(MT41J128M16JT-125),
capable of running at 400MHz. Adding this specific DDR configuration
details running at 400MHz.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In AM335x the card detect gpio is designed as active low gpio.
So correcting the dt card detect gpio definition.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Allow am335x-bone.dts to be built and enable uart and timer
for all beaglebones.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Adds an fdt.c file in that defines the ft_cpu_setup() function,
which should be called from a board-specific ft_board_setup()).
This ft_cpu_setup() will currently do nothing for non-secure (GP)
devices but contains pertinent updates for booting on secure (HS)
devices.
Update the omap5 Makefile to include the fdt.c in the build.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the CPU string output so that the device
type is now included as part of the CPU string that
is printed as the SPL or u-boot comes up. This update
adds a suffix of the form "-GP" or "-HS" for production
devices, so that general purpose (GP) and high security
(HS) can be distiguished. Applies to all OMAP5 variants.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Updates the SPL build so that when CONFIG_TI_SECURE_DEVICE
is in use (which it should be when building for secure parts),
the TI secure development package is used to create a valid
secure boot image. The u-boot SPL build processes is NOT aware
of the details of creating the boot image - all of that information
is encapsulated in the TI secure development package, which is
available from TI. More info can be found in README.ti-secure
Right now, two image types are generated, MLO and X-LOADER. The types
are important, as certain boot modes implemented by the device's ROM
boot loader require one or the other (they are not equivalent). The
output filenames are u-boot-spl_HS_MLO and u-boot-spl_HS_X-LOADER. The
u-boot-spl_HS_MLO image is also copied to a file named MLO, which is
the name that the device ROM bootloader requires for loading from the
FAT partition of an SD card (same as on non-secure devices).
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Modifies the config.mk to build secure images when building
the SPL for secure devices.
Depending on the boot media, different images are needed
for secure devices. The build generates u-boot*_HS_* files
as appropriate for the different boot modes. The same u-boot
binary file is processed slightly differently to produce a
different boot image, depending on whether the user wants to
boot off SPI, QSPI or other boot media.
Refer to README.ti-secure for more information.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adds a centralized config_secure.mk in omap-common for
OMAP-style TI secure devices to use for boot image generation
Depending on the boot media, different images are needed for
secure devices. These commands generates u-boot*_HS_* files that
need to be used to boot secure devices.
Please refer to README.ti-secure for more information.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Defines CONFIG_TI_SECURE_DEVICE which needs to be turned on
when building images for secure devices. This flag is used
to invoke the secure image creation tools for creating a
boot image that can be used on secure devices. This flag
may also be used to conditionally compile code specific
to secure devices.
This terminology will be used by all OMAP architecture devices,
hence introducing to a common location.
With the creation of Kconfig for omap-common, moved the
sourcing of the Kconfig files for the omap3/4/5 and am33xx
devices from arch/arm/KConfig to the omap-common one.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adding support for AM43xx secure devices require the addition
of some SOC specific config options like the amount of memory
used by public ROM and the address of the entry point of u-boot
or SPL, as seen by the ROM code, for the image to be built
correctly.
This mandates the addition of am AM43xx CONFIG option and the
ARM Kconfig file has been modified to source this SOC Kconfig
file. Moving the TARGET_AM43XX_EVM config option to the SOC
KConfig and out of the arch/arm/Kconfig.
Updating defconfigs to add the CONFIG_AM43XX=y statement and
removing the #define CONFIG_AM43XX from the header file.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adds a new Kconfig file for AM33xx class devices. We
need a common place to define CONFIG parameters
for these SOCs, especially for adding support
for secure devices.
a) Adds a definition for ISW_ENTRY_ADDR. This is the
address to which the ROM branches when the SOC
ROM hands off execution to the boot loader.
CONFIG_SYS_TEXT_BASE and CONFIG_SPL_TEXT_BASE are set
to this value for AM43xx devices.
b) Adds CONFIG_PUB_ROM_DATA_SIZE which is used to
calculate CONFIG_SPL_MAX_SIZE. This value indicates the
amount of memory needed by the ROM to store data during
the boot process.
Currently, these CONFIG options are used only by AM43xx,
but in future other AM33xx class SOCs will also use them.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since CONFIG_OF_BOARD_SETUP depends on CONFIG_OF_LIBFDT:
config OF_BOARD_SETUP
bool "Set up board-specific details in device tree before boot"
depends on OF_LIBFDT
...
remove superfluous tests of CONFIG_OF_LIBFDT when testing for
CONFIG_OF_BOARD_SETUP.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
[trini: Typo fix: s/ifdefi/ifdef/]
Signed-off-by: Tom Rini <trini@konsulko.com>
These are no longer used. The migration is complete. Drop these options.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Angelo Dureghello <angelo@sysam.it>
Acked-by: Andreas Bießmann <andreas@biessmann.org>
Since generic board init is enabled, this is not used. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Since generic board init is enabled, this is not used. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Angelo Dureghello <angelo@sysam.it>
Since generic board init is enabled, this is not used. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andreas Bießmann <andreas@biessmann.org>
It is well past the deadline for conversion to generic board init. Remove
the old code.
Please test this and perhaps send a follow-up patch if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
This includes the following fixes:
- Define needed __init_end symbol - see initr_reloc_global_data()
- Drop SH-specific struct bd_info
- Add an empty relocate_code() function
This prevents build errors with generic board, but the code will still need
work. Perhaps this is a better alternative than deleting the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is well past the deadline for conversion to generic board init. Remove
the old code.
Stefan, can you test this please and perhaps send a follow-up patch if needed?
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds platform code for the Amlogic Meson GXBaby (S905) SoC and a
board definition for ODROID-C2. This initial submission only supports
UART and Ethernet (through the existing Designware driver). DTS files
are the ones submitted to Linux arm-soc for 4.7 [1].
[1] https://patchwork.ozlabs.org/patch/603583/
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a psci_system_reset() which calls the SYSTEM_RESET function of
PSCI 0.2 and can be used by boards that support it to implement
reset_cpu().
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable CONFIG_BLK to move to using driver model for block devices. This
affects MMC booting in SPL, as well as MMC access in U-Boot proper.
Signed-off-by: Simon Glass <sjg@chromium.org>
u-boot only recognize okay to enable a node (Linux seems to be more
lenient here). So use okay instead.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a definition for the gmac interface to the firefly device-tree.
Copied verbatim from the linux kernel.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Add definitions for GRF_SOC_CON1 and GRF_SOC_CON3 which contain various
GMAC related fields.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Setup the clocks for the gmac ethernet interface. This assumes the mac
clock is fed by an external clock which is common on RK3288 based
devices.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a sandbox mailbox implementation (provider), a test client
device, instantiates them both from Sandbox's DT, and adds a DM test
that excercises everything.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org> # v1
The current reset API implements a method to reset the entire system.
In the near future, I'd like to introduce code that implements the device
tree reset bindings; i.e. the equivalent of the Linux kernel's reset API.
This controls resets to individual HW blocks or external chips with reset
signals. It doesn't make sense to merge the two APIs into one since they
have different semantic purposes. Resolve the naming conflict by renaming
the existing reset API to sysreset instead, so the new reset API can be
called just reset.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
If CONFIG_SPL_SERIAL_SUPPORT is not defined in include/configs/exynos5-common.h
the following error is produced during the build of the SPL:
arch/arm/mach-exynos/built-in.o: In function `do_lowlevel_init':
...u-boot/arch/arm/mach-exynos/lowlevel_init.c:221: undefined reference to `debug_uart_init'
Add additional condition to check if SPL build is in progress and
in that case check if CONFIG_SPL_SERIAL_SUPPORT is also set before
enabling the debug UART.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
GCC 5.3 report a warning: 'upper' and 'lower' may be used
uninitialized in this function [-Wmaybe-uninitialized].
Compiler might need explicit initializer.
Signed-off-by: Wills Wang <wills.wang@live.com>
We need reset the Ethernet Switch analog part before operation,
or the build-in Ethernet PHY don't work.
Signed-off-by: Wills Wang <wills.wang@live.com>
Acked-by: Marek Vasut <marex@denx.de>
Remove the remnants of JZ4740 support.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Certain chips, like the JZ47xx, have extreme size constraints on the
SPL size and require custom start.S . Allow overriding the start.S
the same way ARM MXS does it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Make use of device model & device tree to probe the UART driver. This is
the initial step in bringing Malta up to date with driver model, and
allows for cleaner handling of the different I/O addresses for different
system controllers by specifying the ISA bus address instead of a
translated memory address.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Recently a set of CONFIG_CMD_FOO defines was moved from being defined
in config_distro_defaults to Kconfig, and added to all sunxi defconfigs
to compensate.
Instead of explictly selecting these in all sunxi defconfigs,
simply always select these for sunxi boards. This makes the defconfigs
simpler and ensures a consistent set of available commands across all
sunxi boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The originally committed .dts files for the Pine64 were from an early
proof-of-concept version and should have never been committed upstream.
Replace them with much more mature versions, which also use a different
naming scheme.
Please note that at this point there is at least one binding which has
not been agreed upon, so this is subject to change.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This addresses a cosmetic issue when booting a sunxi device
over USB (FEL mode), where the SPL currently would just print
"Trying to boot from ". The patch fixes that to properly read
"Trying to boot from FEL".
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The current SPL header, created by the 'mksunxiboot' tool, has size
32 bytes. But the code in the boot ROM stores the information about
the boot media at the offset 0x28 before passing control to the SPL.
For example, when booting from the SD card, the magic number written
by the boot ROM is 0. And when booting from the SPI flash, the magic
number is 3. NAND and eMMC probably have their own special magic
numbers too.
Currently the corrupted byte is a part of one of the instructions in
the reset vectors table:
b reset
ldr pc, _undefined_instruction
ldr pc, _software_interrupt <- Corruption happens here
ldr pc, _prefetch_abort
ldr pc, _data_abort
ldr pc, _not_used
ldr pc, _irq
ldr pc, _fiq
In practice this does not cause any visible problems, but it's still
better to fix it. As a bonus, the reported boot media type can be
later used in the 'spl_boot_device' function, but this is out of
the scope of this patch.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The A80 uses the AXP809 as its primary PMIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This header will be shared between PH1-LD11 and PH1-LD20
(and hopefully new ARMv8 SoCs developed in the future),
so umc64-regs.h would be a better fit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Boot ROM has enabled D-cache and MMU setting DDR memory area
as Normal Memory in its page table. Disable D-cache and MMU
before jumping to U-Boot proper.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Update several boards to use driver model for video. This involves changes
to the EDP and FIMD (frame buffer) drivers. Existing PWM, simple-panel and
pwm-backlight drivers are used. These work without additional configuration
since they use the device tree settings in the same way as Linux.
Boards converted are:
- snow
- spring
- peach-pit
- peach-pi
All have been tested. Not converted:
- MIPI display driver
- s5pc210_universal
- smdk5420
- smdk5250
- trats
- trats2
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rename this function to better fit with driver model. It is the private data
for the exynos EDP driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Bring in device tree pieces related to display from Linux 4.4 for:
- snow
- peach_pit
- peach_pi
- spring
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This function controls enabling the EDP PHY. Rename it and drop the existing
weak functions, which are confusing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This is commonly used for LCD backlight control. Add pinmux support for it
on exynos5250 and 5420.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add this node from Linux v4.4 so that PWMs can be used in U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This driver supports the standard PWM API. There are 5 PWMs. Four are used
normally and the last is normally used as a timer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In preparation for making this a parameter, move it into the function
that sets it up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Put the pointer to this structure in struct vidinfo so that we can
reference it without it being global.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Use 'struct vidinfo' instead so that we can change this to a struct with a
different name in future.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
We always use device tree with video, so can drop these #ifdefs. Some of the
hardware addresses are not needed either.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Espresso7420 is a development/evaluation board for Exynos7420 SoC. It
includes multiple onboard compoments (EMMC/Codec) and various
interconnects (USB/HDMI).
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add support for Exynos7420 SoC. The Exynos7420 SoC has four Cortex-A57
and four Cortex-A53 CPUs and includes various peripheral controllers.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The existing Exynos 32-bit platform support needs to be realigned in
order to support newer 64-bit Exynos platforms. The driver model will
be utlized for drivers on the 64-bit Exynos platforms and so some of
the older platform support code would not be required for the newer
64-bit Exynos platforms.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
While enabling L2 cache, the value of L2PE (L2 cache parity/ECC
error checking enable) must not be changed while the L2 cache is
enabled.
So, L2PE must be set before enabling L2 cache.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Fix typo error for cpsw device name with proper device address
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add syscon node to cpsw device node to read mac address
from efuse.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add syscon node to cpsw device node to read mac address
from efuse.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add platforms specific phy mode configuration bits to be used
to configure phy mode in control module.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
To i.MX6DQPlus, osc can be choosed as the source of gpt, so
add i.MX6DQPlus support in gpt_has_clk_source_osc.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
The i.MX6DQPlus support sata interface, we should not
return failure when CPU is i.MX6DQPlus.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Support i.MX6DQPlus, otherwise wrong hab address will be used
for i.MX6QDPlus.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Ulises Cardenas <Ulises.Cardenas@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Correct get_cpu_speed_grade_hz for i.MX6DQP, otherwise we
will get wrong speed grade info i.MX6DQP.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Add i.MX6SOLO support for hab function.
The difference between i.MX6SOLO and i.MX6DL is
the number of CPU cores. Besides this, they work
the same.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: "Benoît Thébaudeau" <benoit.thebaudeau.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Use simpler runtime cpu dection macros.
i.MX6DL and i.MX6SOLO work the same, so use is_mx6sdl.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
i.MX6DL and i.MX6SOLO work the same, add i.MX6SOLO support
when enable/disable_ldb_di_clock_sources.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Extending Kconfig for adding new platform is a lot of work
for nothing. Setting SYS_CONFIG_NAME directly in Kconfig and
remove all dependencies on TARGET_ZYNQ_* options including SPL.
As a side-effect it also remove custom init folder for ps7_init_gpl.*
files. Folder is chosen based on device-tree file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Support RAM and MMC boot mode in SPL also with SPL_FIT images.
In MMC boot mode two boot options are available:
1) Boot flow with ATF(EL3) and full U-Boot(EL2):
aarch64-linux-gnu-objcopy -O binary bl31.elf bl31.bin
mkimage -A arm64 -O linux -T kernel -C none -a 0xfffe5000 -e 0xfffe5000
-d bl31.bin atf.ub
cp spl/boot.bin <sdcard fat partition>
cp atf.ub <sdcard fat partition>
cp u-boot.bin <sdcard fat partition>
2) Boot flow with full U-Boot(EL3):
cp spl/boot.bin <sdcard>
cp u-boot*.img <sdcard>
3) emmc boot mode
dd if=/dev/zero of=sd.img bs=1024 count=1024
parted sd.img mktable msdos
parted sd.img mkpart p fat32 0% 100%
kpartx -a sd.img
mkfs.vfat /dev/mapper/loop0p1
mount /dev/mapper/loop0p1 /mnt/
cp spl/boot.bin /mnt
cp u-boot.img /mnt
cp u-boot.bin /mnt
cp atf.ub /mnt
umount /dev/mapper/loop0p1
kpartx -d sd.img
cp sd.img /tftpboot/
and program it via u-boot
tftpb 10000 sd.img
mmcinfo
mmc write 10000 0 $filesize
mmc rescan
mmc part
ls mmc 0
psu_init() function contains low level SoC setup generated for every HW
design by Xilinx design tools. xil_io.h is only supporting file to fix
all dependencies from tools. The same solution was used on Xilinx Zynq.
The patch also change CONFIG_SYS_INIT_SP_ADDR to the end of OCM which
stays at the same location all the time.
Bootrom expects starting address to be at 0xfffc0000 that's why this
address is SPL_TEXT_BASE.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The GIC ranges in the zynqmp device tree are only 4kb aligned. Since
commit 12e14066f we automatically deal with aliases GIC regions though,
so we can map them transparently into guests even on 64kb page size
systems.
This patch makes use of that features and sets GICC and GICV to 64kb
aligned and sized regions.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
