The User Register in GMAC IP is used to select interface type.
When with GE feature, it is used to select interface between
RGMII and GMII. If without GE feature, it is used to select
interface between MII and RMII.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
When boot up without mac address setting, it will give the warning
message like: "Warning: failed to set MAC address", however when
execute network related command, it still execute them without any
warning information.
With this patch, it will exit directly with following information:
"gmac0: mac address is not valid"
It also solve the problem after bootup then set mac address and the
mac address won't set to net device issue.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
NEG bit default is '1' for external MDIOs as per FMAN-v3 RM, but on some
platforms, e.g. T2080QDS, this bit is '0', which leads to MDIO failure
on XAUI PHY, so set this bit definitely to align with the RM.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. use Payload length check disable when enable MAC;
2. add XGMII support for setting MAC interface mode;
3. only enable auto negotiation for Non-XGMII mode;
4. return 0xffff if clause 22 is used to read 10G phy_id;
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-By: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Fix error detected by cppcheck:
[drivers/net/uli526x.c:551]: (error) printf format string requires 3
parameters but only 2 are given.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Roy Zang <tie-fei.zang@freescale.com>
Make sure to keep the MAC address programmed in the SMC911x ADDRH
and ADDRL registers. Linux can read those registers to determine
the MAC address on EEPROM-less configurations.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Tom Rini <trini@ti.com>
As per Marvell Release Notes - Alaska 88E1510/88E1518/88E1512/88E1514
Rev A0, Errata Section 3.1 Marvell PHY has an errata which requires
that certain registers get written in order to restart
autonegotiation.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Keystone2 Lamar SoC uses the same keystone net driver.
This patch adds opportunity to use it by K2L SoCs.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Keystone2 Lamar SoC uses the same keystone SerDes driver.
All Keystone2 EVM boards currently use SerDes driver, so move
CONFIG_TI_KEYSTONE_SERDES to common configuration file.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
A bit field of DMA descriptor is on memory area of DMA. If we set data
to bit of DMA descriptor, we must be writeback data of DMA descriptor.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
RX_DESC_SIZE and TX_DESC_SIZE mean the size of the data descriptor for sh-eth.
We can acquire this in sizeof. It is not necessary to define these in define.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
R8A7793 has the same sh-ether IP core as other SH/rmobile.
This patch adds support of R8A7793.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
I finally had a look at the datasheet and spotted an additional
register address difference between regular E1000 and i210/i211 chips.
This patch fixes this and now successfully works on programmed
i210/i211 as well as unprogrammed i211.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Commit 951860634f may have changed
the logic unintentially from "if (!(swfw_sync & (fwmask | swmask)))"
to "if ((swfw_sync & swmask) && !(swfw_sync & fwmask))". This change
breaks some e1000 NIC with a message "ERROR: Unable to read EEPROM!".
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Marek Vasut <marex@denx.de>
CC: Tim Harvey <tharvey@gateworks.com>
Acked-by: Marcel Ziswiler <marcel@ziswiler.com>
The file board/Marvell/include/mv_gen_reg.h is incompatible with
the GPL (see for example the "MARVELL RESERVES THE RIGHT AT ITS SOLE
DISCRETION TO REQUEST THAT THIS CODE BE IMMEDIATELY RETURNED TO
MARVELL" clause). As this cannot be fixed, we remove the file and all
code that depends on it. Fortunately this only affects some very old
boards that have long reached EOL:
CPCI750
DB64360
DB64460
p3m750
p3m7448
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
get_phy_id is marked weak but has no protype nor a
strong version, just make it static. Use __weak for
board_phy_config.
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
The new Marvel PHY (88E1514) used on K2L/K2E EVM requires longer time
to auto negotiate with SoC's SGMII port.
It can take about 3 sec to up the PHY after reset, so add code to
expose sgmii auto negotiation waiting process.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The Keystone2 Edison SoC uses the same keystone net driver.
This patch adds opportunity to use it by K2E SoCs.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Keystone2 Edison SoC uses the same keystone SerDes driver.
This patch adds support for K2E SoCs.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The phy framework has function to get link, so use it
instead of own implementation.
There is no reason to check SGMII link while sending each
packet, phy link is enough. Check SGMII link only while
ethernet open.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
As MDIO bus has been added we can register PHYs with it.
After registration, the PHY driver will be probed according to the
hardware on board.
Startup PHY at the ethernet open.
Use phy_startup() instead of keystone_get_link_status() when eth open,
as it verifies PHY link inside and SGMII link is checked before.
For K2HK evm PHY configuration at init was absent, so don't enable
phy config at init for k2hk evm.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Currently MDIO framework is not used to configure Ethernet PHY.
As result some of already implemented functions are duplicated.
So register MDIO bus in order to use it. On that stage it's just
registered, it'll be used as we start to use PHY framework.
Use mdio bus read/write/reset functions in the driver.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Don't use mdio_enable twice while eth open. Also rename it to
keystone2_mdio_reset as more appropriate name.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
In case when several Ethernet ports are supported it's
convenient to see the number of phy that is not found.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
SerDes driver is used by other sub systems like PCI, sRIO etc.
So modify it to be more general. The SerDes driver provides common
API's that can also be extended for other peripherals SerDes
configurations.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch split the Keystone II SGMII SerDes related code from
Ethernet driver and create a separate SGMII SerDes driver.
The SerDes driver can be used by others keystone subsystems
like PCI, sRIO, so move it to driver/soc/keystone directory.
Add soc specific drivers directory like in the Linux kernel.
It is going to be used by keysotone soc specific drivers.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Remove unused tx_send_loop variable.
Removes duplicated get_link_status() call from the
keystone2_eth_send_packet().
The emac_gigabit_enable() is called at opening Ethernet and there is no
need to enable it on sending each packet. So remove that call
from keystone2_eth_send_packet() as well.
The calling of power/clock up functions are mostly the responsibility
of SoC/board code, so move these functions to appropriate place.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The header file for the driver should be in correct place.
So move it to "arch/arm/include/asm/ti-common/keystone_net.h"
and correct driver's external dependencies. At the same time
align and correct some definitions.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch removes K2HK SOC specifc emac_regs structure, it uses
soc specific register offset to keep the network driver common across
all the Keystone II EVMs.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The keystone_nav driver is general driver intended to be used for
working with queue manager and pktdma for different IPs like NETCP,
AIF, FFTC, etc. So the it's API shouldn't be named like it works only
with one of them, it should be general names. The names with prefix
like netcp_* rather do for drivers/net/keystone_net.c driver. So it's
good to generalize this driver to be used for different IP's and
delete confusion with real NETCP driver.
The current netcp_* functions of keystone navigator can be used for
other settings of pktdma, not only for NETCP. The API of this driver
is used by the keystone_net driver to work with NETCP, so net driver
also should be corrected. For convenience collect pkdma
configurations in drivers/dma/keystone_nav_cfg.c.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The keystone_nav is used by drivers/net/keystone_net.c driver to
send and receive packets, but currently it's placed at keystone
arch sources. So it should be in the drivers directory also.
It's separate driver that can be used for sending and receiving
pktdma packets by others drivers also.
This patch just move this driver to appropriate directory and
doesn't add any functional changes.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch adds support for the NETA ethernet controller which is integrated
in the Marvell Armada XP SoC's. This port is based on the Linux driver which
has been stripped of the in U-Boot unused portions.
Tested on the Marvell MV78460 eval board db-78460-bp.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Tested-by: Luka Perkov <luka@openwrt.org>
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Add a few new variables to make the cache handling less cryptic.
Add a variable for DMA and DATA descriptor start and end, so the
correctness of the code is easier to inspect.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Chin Liang See <clsee@altera.com>
Fix remaining cache alignment issues in the DWC Ethernet driver.
Please note that the cache handling in the driver is making the
code hideous and thus the next patch cleans that up. In order to
make this change reviewable though, the cleanup is split from it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Pavel Machek <pavel@denx.de>
Old saying says that more than three exclamation marks in a row are
sign of mental disease. Cleanup micrel.c.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Chin Liang See <clsee@altera.com>
This would be useful to start moving various config options.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Fix the following build error in case CONFIG_E1000_NO_NVM is enabled:
CC drivers/net/e1000.o
drivers/net/e1000.c: In function ‘e1000_initialize’:
drivers/net/e1000.c:5365:5: error: ‘struct e1000_hw’ has no
member named ‘eeprom_semaphore_present’
make[1]: *** [drivers/net/e1000.o] Error 1
make: *** [drivers/net] Error 2
Acked-by: Marek Vasut <marex@denx.de>
T1042QDS (T1042 is T1040 Personality without L2 switch) supports following
sgmii interfaces with serdes protocol 0xA7
-SGMII-MAC3 on Lane B - slot 7
-SGMII-MAC5 on Lane H - slot 7
-SGMII2.5G-MAC1 on Lane C - slot 6
-SGMII2.5G-MAC2 on Lane D - slot 5
Add support of above sgmii interfaces
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
When network protocol errors occur (such as a file not being found on a
TFTP server), the processing done by the NetReceive() function will end
up calling the driver's .halt() implementation. However, after that the
device no longer has access to the memory buffers and will cause errors
such as this in the rtl_recv() function when trying to hand descriptors
back to the device:
pci_hose_bus_to_phys: invalid physical address
This can be fixed by deferring processing of network packets until the
descriptors have been handed back. That way rtl_halt() tearing down
network buffers is not going to prevent access to the buffers.
Reported-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use size_t type for positive offsets instead of the loff_t type. The
later is defined as long long, which is larger than the pointer type
on OpenRISC architecture and therefore the following warning was
generated:
"warning: cast to pointer from integer of different size"
Signed-off-by: Vasili Galka <vvv444@gmail.com>
When testing the FEC driver on a mx6solox we noticed that the TDAR bit gets
always cleared prior then the READY bit is cleared in the last BD, which causes
FEC packets reception to always fail.
As explained by Ye Li:
"The TDAR bit is cleared when the descriptors are all out from TX ring, but on
mx6solox we noticed that the READY bit is still not cleared right after TDAR.
These are two distinct signals, and in IC simulation, we found that TDAR always
gets cleared prior than the READY bit of last BD becomes cleared.
In mx6solox, we use a later version of FEC IP. It looks like that this
intrinsic behaviour of TDAR bit has changed in this newer FEC version."
Fix this by polling the READY bit of BD after the TDAR polling, which covers the
mx6solox case and does not harm the other SoCs.
No performance drop has been noticed with this patch applied when testing TFTP
transfers on several boards of different i.mx SoCs.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
mx6solox has a requirement for 64 bytes alignment for RX DMA transfer.
Other SoCs work with the standard 32 bytes alignment.
Adjust it accordingly by using 64 bytes aligment in the FEC RX DMA buffers,
which addresses the needs from mx6solox and also works for the other SoCs.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
This patch is to add etsec support for LS102xA. First, Little-endian
descriptor mode should be enabled. So RxBDs and TxBDs are interpreted
with little-endian byte ordering. Second, TSEC_SIZE and TSEC_MDIO_OFFSET
are different from PowerPC, redefine them for LS1021xA.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
fsl_enet.h defines the mapping of the usual MII management
registers, which are included in the MDIO register block
common to Freescale ethernet controllers. So it shouldn't
depend on the CPU architecture but it should be actually
part of the arch independent fsl_mdio.h.
To remove the arch dependency, merge the content of
asm/fsl_enet.h into fsl_mdio.h.
Some files (like fm_eth.h) were simply including fsl_enet.h
only for phy.h. These were updated to include phy.h instead.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
There is no reason to redefine pure readl/writel functions.
So remove this redundancy.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Vitaly Andrianov <vitalya@ti.com>
The Broadcom StarFighter2 Ethernet driver is used in multiple Broadcom
SoC(s) and:
- supports multiple MAC blocks,
- provides support for the Broadcom GMAC.
This driver requires MII and PHYLIB.
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
We noticed on the DXR2 platform (AM335x with a SMSC LAN9303 switch connected
to the CPSW MAC) that the network performance in U-Boot is quite poor. Only
when the transfer is started without a cable connected, and the cable is
plugged after the first timeout "T" occured, an increased in performance
can be seen. Debugging has revealed, that the cpsw driver has constant
link checking builtin into the rx and tx functions. This results in the
bad performance and seems to be unnecessary. The link has already been
checked in the init function, before the transfer is started. This usually
is sufficient.
BTW: I have seen no other network driver in U-Boot so far, that constantly
checks for link in the rx / tx functions.
The performance numbers on the DXR2 board are:
0.56 MiB/s cpsw_check_link() in rx and tx path
0.87 MiB/s cpsw_check_link() only in tx path
1.0 MiB/s cpsw_check_link() only in rx path
2.7 MiB/s no cpsw_check_link() in rx and tx path
So with this patch the network performance on DXR2 increases from 0.56
to 2.7 MiB/s (nearly 5 times as fast).
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Samuel Egli <samuel.egli@siemens.com>
Tested-by: Heiko Schocher <hs@denx.de>
Cc: Vladimir Koutny <vladimir.koutny@streamunlimited.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement proper support for cache flushing and invalidation into the
Intel e1000 NIC driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
The following configs are not defined at all:
- CONFIG_INCA_IP_SWITCH
- CONFIG_PBL2800_ETHER
- CONFIG_PHY_ICPLUS
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
XFI is supported on T4QDS-XFI board, which removed slot3, and four LANEs
of serdes2 are routed to a SFP+ cages, which to house fiber cable or
direct attach cable(copper), the copper cable is used to emulate the
10GBASE-KR scenario.
So, for XFI usage, there are two scenarios, one will use fiber cable,
another will use copper cable. For fiber cable, there is NO PHY, while
for copper cable, we need to use internal PHY which exist in Serdes to
do auto-negotiation and link training, which implemented in kernel.
We use hwconfig to define cable type for XFI, and fixup dtb based on the
cable type.
For copper cable, set below env in hwconfig:
fsl_10gkr_copper:<10g_mac_name>
the <10g_mac_name> can be fm1_10g1, fm1_10g2, fm2_10g1, fm2_10g2. The
four <10g_mac_name>s do not have to be coexist in hwconfig. For XFI ports,
if a given 10G port will use the copper cable for 10GBASE-KR, set the
<10g_mac_name> of the port in hwconfig, otherwise, fiber cable will be
assumed to be used for the port.
For ex. if four XFI ports will both use copper cable, the hwconfig
should contain:
fsl_10gkr_copper:fm1_10g1,fm1_10g2,fm2_10g1,fm2_10g2
For fiber cable:
1. give PHY address to a XFI port, otherwise, the XFI ports will not be
available in U-boot, there is no PHY physically for XFI when using fiber
cable, this is just to make U-boot happy and we can use the XFI ports
in U-boot.
2. fixup dtb to use fixed-link in case of fiber cable which has no PHY.
Kernel requests that a MAC must have a PHY or fixed-link.
When using XFI protocol, the MAC 9/10 on FM1 should init as 10G interface.
Change serdes 2 protocol 56 to 55 which has same feature as 56 since 56
is not valid any longer.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Messages to afleming@freescale.com now bounce, and should be
directed to my personal address at afleming@gmail.com
Signed-off-by: Andy Fleming <afleming@gmail.com>
R8A7794 has the same sh-ether IP core as other SH/rmobile.
This patch adds support of R8A7794.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
At present stdio device functions do not get any clue as to which stdio
device is being acted on. Some implementations go to great lengths to work
around this, such as defining a whole separate set of functions for each
possible device.
For driver model we need to associate a stdio_dev with a device. It doesn't
seem possible to continue with this work-around approach.
Instead, add a stdio_dev pointer to each of the stdio member functions.
Note: The serial drivers have the same problem, but it is not strictly
necessary to fix that to get driver model running. Also, if we convert
serial over to driver model the problem will go away.
Code size increases by 244 bytes for Thumb2 and 428 for PowerPC.
22: stdio: Pass device pointer to stdio methods
arm: (for 2/2 boards) all +244.0 bss -4.0 text +248.0
powerpc: (for 1/1 boards) all +428.0 text +428.0
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Some of the fm_port_to_index() callers did not check for -1 return value and
used -1 as an array index.
Signed-off-by: Marian Rotariu <marian.rotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
There have been 3 versions of the sunxi_emac support patch during its
development. Somehow version 2 ended up in upstream u-boot where as
the u-boot-sunxi git repo got version 3.
This bumps the version in upstream u-boot to version 3 of the patch:
- Initialize MII clock earlier so mii access to allow independent use
- Name change from WEMAC to EMAC to match mainline kernel & chip manual
- Cosmetic code cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Adding support to load and start the Layerscape Management Complex (MC)
firmware. First, the MC GCR register is set to 0 to reset all cores. MC
firmware and DPL images are copied from their location in NOR flash to
DDR. MC registers are updated with the location of these images.
Deasserting the reset bit of MC GCR register releases core 0 to run.
Core 1 will be released by MC firmware. Stop bits are not touched for
this step. U-boot waits for MC until it boots up. In case of a failure,
device tree is updated accordingly. The MC firmware image uses FIT format.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Add to code to flush the dcache after we writing in DMA buffer.
Also we need invalidate the dcache before we check the status in the
DMA buffer.
Tested in SAMA5D3x-EK with gmac0. Tftp download speed shows in below:
Disable DCache: 1.1 MiB/s
Enable DCache: 1.6 MiB/s
Increase speed with about 40%.
The code should have no impact with the boards which are not
enable_dcache().
Tested in AT91SAM9M10G45EK.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This also renames the CONFIG_SYS_MACB_xx defines. They are used just local and
therefore don't need the CONFIG_SYS_ prefix.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Josh Wu <josh.wu@atmel.com>
'r' of rESR_RTLF is a mistake of E.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The R7S72100 of ARM SoC that Renesas manufactured has one Ether port.
This has the same IP SH-Ether. This patch adds support of the R7S72100
in SH-Ether.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
get_phy_id returns -EIO when it can't read from a phy at a given addr. This would cause
create_phy_by_mask to return prematurely before it had tested the other addresses in the provided mask.
Example usage:
Replace
phydev = phy_connect(bus, phy_addr, dev, phy_if)
with
phydev = phy_find_by_mask(bus, phy_mask, phy_if)
if (phydev)
phy_connect_dev(phydev, dev);
Signed-off-by: Cormier, Jonathan <jcormier@criticallink.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
The correct value for this setting can vary across SoCs and boards, so make it
configurable.
Also reduce the default value to 8, which is the same default as used in the
Linux driver.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
On Thu, 2014-05-08 at 22:26 +0100, Ian Campbell wrote:
> The {r,t}xbuffs fields also need to be aligned. Previously this was done
> implicitly because they immediately followed the descriptor tables. Make this
> explicit and also move to the head of the struct.
Looks like I managed to not actually commit the move of the field to the
head of the struct! v3.1 follows....
Ian.
8<------------
>From 2937ba01841887317f6792709ed57cb86b5fc0cd Mon Sep 17 00:00:00 2001
From: Ian Campbell <ijc@hellion.org.uk>
Date: Thu, 1 May 2014 19:45:15 +0100
Subject: [PATCH] net/designware: reorder struct dw_eth_dev to pack more
efficiently.
The {tx,rx}_mac_descrtable fields are aligned to ARCH_DMA_MINALIGN, which could
be 256 or even larger. That means there is a potentially huge hole in the
struct before those fields, so move them to the front where they are better
packed.
Moving them to the front also helps ensure that so long as dw_eth_dev is
properly aligned (which it is since "net/designware: ensure device private data
is DMA aligned.") the {tx,rx}_mac_descrtable will be too, or at least avoids
having to worry too much about compiler specifics.
The {r,t}xbuffs fields also need to be aligned. Previously this was done
implicitly because they immediately followed the descriptor tables. Make this
explicit and also move to the head of the struct.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
This is required at least on ARM.
When sending instead of simply invalidating the entire descriptor, flush
as little as possible while still respecting ARCH_DMA_MINALIGN, as
requested by Alexey.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
struct dw_eth_dev contains fields which are accessed via DMA, so make sure it
is aligned to a dma boundary. Without this I see:
ERROR: v7_dcache_inval_range - start address is not aligned - 0x7fb677e0
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Marek Vasut <marex@denx.de>
This patch adds support for VSC8664 PHY module which can
be found on Freescale's T4240RDB boards.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The T4080 SoC is a low-power version of the T4160.
T4080 combines 4 dual-threaded Power Architecture e6500
cores with single cluster and two memory complexes.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Current driver uses a Maximum value for MDIO_HOLD when doing 10G MDIO
access, this is due to an errata A-006260 on T4 rev1.0 which is fixed
on rev2.0, so remove the maximum value to use the default value for rev2.0.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
This sets up the linkage from the phydev back to the ethernet device. This
symptom of not doing this which I noticed was:
<NULL> Waiting for PHY auto negotiation to complete....
rather than:
dwmac.1c50000 Waiting for PHY auto negotiation to complete....
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Some functions in include/net.h are ported from
include/linux/etherdevice.h of Linux Kernel.
For ex.
is_zero_ether_addr()
is_multicast_ether_addr()
is_broadcast_ether_addr()
is_valid_ether_addr();
So, we should use the same function name as that of Linux Kernel,
eth_rand_addr(), for consistency.
Besides, eth_rand_addr() has been implemented as an inline function.
So it should not be surrounded by #ifdef CONFIG_RANDOM_MACADDR.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As some PHYs have non-standard PHY ID registers, PHY Id can't
be read correctly by current get_phy_id function, so we enable
get_phy_id redefinable to permit specific PHY driver having own
specific get_phy_id function.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Function "genphy_parse_link()" used "if (mii_reg & BMSR_ANEGCAPABLE)" before,
but used "if (phydev->supported & SUPPORTED_Autoneg)" now.
So assign "phydev->supported" to "phydev->drv->features" for ar8035
to enable autonegotiation. Then removed the genphy_config_aneg() function.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Add missing header.
Warnings:
drivers/net/zynq_gem.c:491:5: warning: symbol 'zynq_gem_initialize' was not declared. Should it be static?
drivers/net/zynq_gem.c:542:5: warning: symbol 'zynq_gem_of_init' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ar8031 has the same config steps with ar8021, so change its
config func to ar8021_config instead of genphy_config.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
MDIO clock needs to be initialized in u-boot code for SoCs
having FMAN-v3(v3H or v3L) controller due to below reasons
-On SoCs that have FMAN-v3H like B4860, default value of
MDIO_CLK_DIV bits in mdio_stat(mdio_cfg) register generates
mdio clock too high (much higher than 2.5MHz), violating the
IEEE specs.
-On SOCs that have FMAN-v3L like T1040, default value of
MDIO_CLK_DIV bits is zero, so MDIO clock is disabled.
So, for proper functioninig of MDIO, MDIO_CLK_DIV bits needs to
be properly initialized.
Also this type of initialization is generally done in
PBI(pre-bootloader) phase using rcw.But for chips like T1040
which support deep-sleep, such type of initialization cannot be
done in PBI phase due to the limitation that during deep-sleep
resume, FMAN (MDIO) registers are not accessible in PBI phase.
So, mdio clock initailization must be done as part of u-boot.
This initialization code is implemented in memac_phy.c which
gets compiled only for SoCs having FMANv3, so no extra compilation
flag is required.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In the current Datasheet for VSC8514 there is a mistake, saying that
the PHY id is 0x70570. The real value in the identifier registers is
0x70670. Linux PHY driver uses 0x70670 also.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
CONFIG_SYS_QE_FMAN_FW_ADDR is used to both Fman and QE for microcode address.
Now using CONFIG_SYS_FMAN_FW_ADDR for Fman microcode address,
and CONFIG_SYS_QE_FW_ADDR for QE microcode address.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This is dead hardware and no one is interested in making the
necessary changes for upcoming features like generic board or
driver model.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
The ordering of accesses to the rx & tx descriptors is important, yet
the send & recv functions accessed them via regular structure accesses.
This leaves the compiler with the opportunity to reorder those accesses
or to hoist them outside of loops. Prevent that from happening by using
readl & writel to access the descriptors. As a nice bonus, this removes
the need for the driver to care about endianness.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
The RX buffers are invalidated when a packet is received, however they
were not suitably cache-line aligned. Allocate them seperately to the
pcnet_priv structure and align to ARCH_DMA_MINALIGN in order to ensure
suitable alignment for the cache invalidation, preventing anything else
being placed in the same lines & lost.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
The prior accesses to the descriptor rings & init block via cached
memory had a few issues:
- The memory needs cache flushes or invalidation at the appropriate
times, but was not necessarily aligned on cache line boundaries.
This could lead to data being incorrectly lost or written back to
RAM at the wrong time.
- There are points where ordering of writes to the memory is
important, but because it's cached memory the pcnet controller
would see cache lines written back ordered by address. This could
occasionally lead to hardware seeing descriptors in an incorrect
state.
- Flushing the cache constantly is inefficient.
So, to avoid all of those issues simply access the descriptors & init
block via uncached memory. The MIPS-specific UNCACHED_SDRAM macro is
used to do this (retrieving an address in kseg1) as I could see no
existing generic solution. Since the MIPS Malta board is the only user
of the pcnet driver, hopefully this doesn't matter.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/lubbock/*
- Remove include/configs/lubbock.h
- Cleanup defined(CONFIG_LUBBOCK)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Ethernet driver configures the CPSW, SGMI and Phy and uses
the the Navigator APIs. The driver supports 4 Ethernet ports and
can work with only one port at a time.
Port configurations are defined in board.c.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
It's important to have ability to flush/invalidate each DMA buffer descriptor
individually to prevent incoherency of adjacent BDs.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
CPSW ia a gigabit device. Use the PHY_GBIT_FEATURES macro to determine phy
supported features.
Tested on cm_t335.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
There was wrong phy_mask for AR8021 device,
so the AR8021 can't be probed correctly.
Changed it from 0x4fffff to 0x4ffff0.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Some platforms like AM437x have different EVMs with different phy addresses,
so this patch adds support for passing phy address via cpsw plaform data.
Also renamed phy_id to phy_addr so better understanding of the code.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
[trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335
pengwyn boards]
Signed-off-by: Tom Rini <trini@ti.com>
- Add xilinx_emaclite_of_init to netdev.h
- Remove global data pointer from the driver
- Add better handling for error state.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
With this, fixup a trivial build error of get_effective_memsize needing
to be updated in the new board/freescale/p1010rdb/spl.c
Signed-off-by: Tom Rini <trini@ti.com>
Function "genphy_parse_link()" used "if (mii_reg & BMSR_ANEGCAPABLE)" before
while "if (phydev->supported & SUPPORTED_Autoneg)" now.
So assign "phydev->supported" to "phydev->drv->features" for ar8031/8033
to enable autonegotiation.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch fixes the following warning messages coming out of
'drivers/net/smc91111.h' when compiled for 'vexpress_aemv8a':
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Currently this issue seems to surface when SMSC is compiled for 64-bit
ARMv8 platforms, so the change is protected under CONFIG_ARM64, so that
it doesn't break other existing platforms.
In addition this patch tries to fix some checkpatch errors and warnings
(others related to camel-casing and volatile usage will be addressed
by a later patch).
This fix has been tested on both ARMv8 foundation model v1 and v2.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
With d6a320d we moved some clock externs out of blackfin_local.h and
into clock.h but now need to include <asm/clock.h> in more drivers to
avoid warnings.
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Tom Rini <trini@ti.com>
Conflicts:
Makefile
drivers/net/npe/Makefile
These two conflicts arise from commit 0b2d3f20
("ARM: NET: Remove the IXP NPE ethernet driver") and are
resolved by deleting the drivers/net/npe/Makefile file
and removing the CONFIG_IXP4XX_NPE line from Makefile.
Now we are ready to switch over to real Kbuild.
This commit disables temporary scripts:
scripts/{Makefile.build.tmp, Makefile.host.tmp}
and enables real Kbuild scripts:
scripts/{Makefile.build,Makefile.host,Makefile.lib}.
This switch is triggered by the line in scripts/Kbuild.include
-build := -f $(if $(KBUILD_SRC),$(srctree)/)scripts/Makefile.build.tmp obj
+build := -f $(if $(KBUILD_SRC),$(srctree)/)scripts/Makefile.build obj
We need to adjust some build scripts for U-Boot.
But smaller amount of modification is preferable.
Additionally, we need to fix compiler flags which are
locally added or removed.
In Kbuild, it is not allowed to change CFLAGS locally.
Instead, ccflags-y, asflags-y, cppflags-y,
CFLAGS_$(basetarget).o, CFLAGS_REMOVE_$(basetarget).o
are prepared for that purpose.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Gerhard Sittig <gsi@denx.de>
commit 626ee1e3 "phylib: update atheros ar803x phy"
leads in failing ethernet on the pxm2 board.
Calling genphy_config() instead of ar8021_config(),
which seems for ar8021 phys not ar803x phys, make
it working again.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Remove hard coded clock divider setting and use the Zynq clock framework
to dynamically calculate appropriate dividers at run time.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The GEM driver should not need to know about Zynq specific details of
RCLK related registers and bitfields in the SLCR. Move those details to
the slcr driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The prescaler value for MDC is calculated wrong for
MX6S. Implement the same logic as linux here which handles
ENET_MAC different then original FEC.
Tested on a custom board with i.MX6S and 100MBit PHY
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Up until now this driver only worked with data cache disabled.
To make it work with enabled data cache following changes were required:
* Flush Tx/Rx buffer descriptors their modification
* Invalidate Tx/Rx buffer descriptors before reading its values
* Flush cache for data passed from CPU to GMAC
* Invalidate cache for data passed from GMAC to CPU
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
With this change driver will benefit from existing phylib and thus
custom phy functionality implemented in the driver will go away:
* Instantiation of the driver is now much shorter - 2 parameters
instead of 4.
* Simplified phy management/functoinality in driver is replaced with
rich functionality of phylib.
* Support of custom phy initialization is now done with existing
"board_phy_config".
Note that after this change some previously used config options
(driver-specific PHY configuration) will be obsolete and they are simply
substituted with similar options of phylib.
For example:
* CONFIG_DW_AUTONEG - no need in this one. Autonegotiation is enabled
by default.
* CONFIG_DW_SEARCH_PHY - if one wants to specify attached phy
explicitly CONFIG_PHY_ADDR board config option has to be used, otherwise
automatically the first discovered on MDIO bus phy will be used
I believe there's no need now in "doc/README.designware_eth" because
user only needs to instantiate the driver with "designware_initialize"
whose prototype exists in "include/netdev.h".
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Driver "init" function might be called multiple times.
On every "init" Tx/Rx buffer descriptors are initialized: "descs_init"
-> "{tx|rx}_descs_init".
In its turn those init functions set MAC's "{tx|rx}desclistaddr" to
point on the first buffer descriptor in the list.
So CPU to start operation from the first buffer descriptor as well after
every "init" we have to reset "{tx|rx}_currdescnum".
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
EMAC_VLANx regs is not properly initiallized in u-boot, once it's overwrite in the
kernel when DSA enabled, hot reset will lead to bringing up EMAC fail in u-boot.
Signed-off-by: Aaron Wu <Aaron.Wu@analog.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
This driver is no longer used, remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
As tsec and fm drivers checking phydev->link
ensure that u-boot don't try access device if link is not ready.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch reverts patch 'add ft_fixup_xgec to support 3rd and 4th 10GEC'.
When dual-role MAC acts as 10G,it still uses fsl,fman-port-1g-rx/tx as before.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
- add more serdes protocols support.
- fix some serdes lanes route.
- fix SGMII doesn't work and incorrect mdio display for XFI when serdes 0x6d.
- correct boot location info for SD/SPI boot.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As tsec and fm drivers checking phydev->link
ensure that u-boot don't try access device if link is not ready.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Bringing in the MMC tree means that CONFIG_BOUNCE_BUFFER needed to be
added to include/configs/exynos5-dt.h now.
Conflicts:
include/configs/exynos5250-dt.h
Signed-off-by: Tom Rini <trini@ti.com>
SH7753 has two fast ethernet controllers and two gigabit ethernet
controllers. It is similar to SH7757.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
As mEMAC1 and mEMAC2 are dual-role MACs, which are used as 1G or 10G MAC.
So we update dynamically 'cell-index' to '2' and '3' for 10GEC3 and 10GEC4.
Also change 'fsl,fman-port-1g-rx' to 'fsl,fman-port-10g-rx', ditto for Tx.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
In 48ec5291, only TX path was optimized; this does the same also for RX
path. This results in huge increase of TFTP throughput on custom am3352
board (from 312KiB/s to 1.8MiB/s) and eliminates occasional transfer
timeouts.
Signed-off-by: Vladimir Koutny <vladimir.koutny@streamunlimited.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Tom Rini <trini@ti.com>
Add support for Freescale T2080/T2081 SoC.
T2080 includes the following functions and features:
- Four dual-threads 64-bit Power architecture e6500 cores, up to 1.8GHz
- 2MB L2 cache and 512KB CoreNet platform cache (CPC)
- Hierarchical interconnect fabric
- One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- 16 SerDes lanes up to 10.3125 GHz
- 8 mEMACs for network interfaces (four 1Gbps MACs and four 10Gbps/1Gbps MACs)
- High-speed peripheral interfaces
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
- Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz
- Additional peripheral interfaces
- Two serial ATA (SATA 2.0) controllers
- Two high-speed USB 2.0 controllers with integrated PHY
- Enhanced secure digital host controller (SD/SDHC/SDXC/eMMC)
- Enhanced serial peripheral interface (eSPI)
- Four I2C controllers
- Four 2-pin UARTs or two 4-pin UARTs
- Integrated Flash Controller supporting NAND and NOR flash
- Three eight-channel DMA engines
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0
Differences between T2080 and T2081:
Feature T2080 T2081
1G Ethernet numbers: 8 6
10G Ethernet numbers: 4 2
SerDes lanes: 16 8
Serial RapidIO,RMan: 2 no
SATA Controller: 2 no
Aurora: yes no
SoC Package: 896-pins 780-pins
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
There are more than two 10GEC in single FMAN in some SoCs(e.g. T2080).
This patch adds support for 10GEC3 and 10GEC4.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
This chip is compatible with the existing driver, except that it uses
BAR2 instead of BAR1 for the I/O memory region. Using this patch I can
use the PCIe ethernet interface on the CompuLab Trimslice to boot from
the network.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Patch: 276477
Instead of directly calling the low-level invalidate_dcache_range() and
flush_cache() functions, provide thin wrappers that take into account
alignment requirements.
While at it, fix a case where the cache was flushed but should have been
invalidated, two cases where the buffer data was flushed instead of the
descriptor and a missing cache invalidation before reading the packet
data that the NIC just wrote to memory.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Patch: 276474
Added d-cache support for zynq_gem.c,
Observed a difference of +0.8 MiB/s when downloading
a file of size of 3007944Bytes.
With d-cache OFF:
----------------
Filename 'uImage'.
Load address: 0x800
Loading: #################################################################
#################################################################
#################################################################
##########
1.3 MiB/s
done
Bytes transferred = 3007944 (2de5c8 hex)
With d-cache ON:
---------------
Filename 'uImage'.
Load address: 0x800
Loading: #################################################################
#################################################################
#################################################################
##########
2.1 MiB/s
done
Bytes transferred = 3007944 (2de5c8 hex)
Changes on zynq_gem for d-cache support:
- Tx and Rx buffers are cache-aligned
- Updated logic for invalidating Rx buffers and flushing Tx buffers.
- Tx and Rx BD's are allocated from non-cacheable region.
(When BDs are cached, we don't see a consistent link)
- Use TX BD status intead of txsr status checks.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When an unprogrammed EEPROM is attached to a dm9000, the dm9000 will
come up with a invalid MAC address of ff:ff:ff:ff:ff:ff. Add code that
gets enabled if CONFIG_RANDOM_MACADDR is enabled that generates a random
(and valid) locally administered MAC address that allows the system to
network boot until a real MAC address can be configured.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
The e1000 driver expects to always have some kind of non-volatile memory
attached directly to the ethernet controller chip. This means that I would
have to add an additional separate flash chip to my custom board just to
store essentially the MAC address. Since I don't want to do that, this patch
introduces a new config option CONFIG_E1000_NO_NVM. If defined it disables
all accesses to the NVM. I have tested the patch with a 82574 controller.
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
The masks were ignoring the last 4 bits which didn't allow detection differences
between the ar8031 and ar8035.
Signed-off-by: Jon Nettleton <jon.nettleton@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Patch: 288018
The both AR8031 and AR8035 belong to Atheros 803x serial PHY.
So the phy id mask of AR8031 is the same to the phy id mask
of AR8035. The right mask value is 0x4fffff.
This patch has been tested on the P1010 and P1023.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Patch: 287748
Fix the 32-bit memory access that is not "endianess safe",
i.e. not giving the desired byte layout for LE cpus:
tempval = *((uint *) (tmpbuf + 4)), where 'char tmpbuf[]'.
Free the stack from rendundant local vars:
tmpbuf[] and i.
Use a portable type (u32) for the 32bit tsec register value
holder: tempval.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Use cross arch portable u32 instead of uint for the
tsec registers. Remove the typedefs for the register
struct definitions in the process. Fix long lines.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Currently, the buffer descriptor (BD) fields cannot be
correctly accessed by a little endian processor. This
patch fixes the issue by making the access of BDs to be
portable among different cpu architectures.
Use portable data types for the Rx/Tx buffer descriptor
fields. Use portable I/O accessors to insure that the
big endian BDs are correctly accessed by little endian
cpus too, and to insure proper sync with the H/W.
Removed the redundant RTXBD "volatile" type, as proper
synchronization around BD data accesses is provided by
the I/O accessors now.
The "sparse" tool was also used to verify the correctness
of these changes.
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Fix bufPtr and the rxIdx/ txIdx occurrences to
solve the related checkpatch warnings for the
coming patches.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Remove tsec_t typedef. Define macros as getters of
tsec and mdio register memory regions, for consistent
initialization of various 'regs' fields and also to
manage overly long initialization lines.
Use the __iomem address space marker to address sparse
warnings in tsec.c where IO accessors are used, like:
tsec.c:394:19: warning: incorrect type in argument 1 (different
address spaces)
tsec.c:394:19: expected unsigned int volatile [noderef]
<asn:2>*addr
tsec.c:394:19: got unsigned int *<noident>
[...]
Add the __iomem address space marker for the tsec pointers
to struct tsec_mii_mng memory mapped register regions.
This solves the sparse warnings for mixig normal pointers
with __iomem pointers for tsec.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Access to privlist[1] (hardcoded referece to the 2nd tsec's
priv area) is neither correct nor does it make sense in the
current context. Each tsec dev has access to its own priv
instance only, and hence to its own set of group address
registers (GADDR) to filter multicast addresses.
This fix leads to removal of the unused (faulty) privlist[]
and related global static vars. Note that mcast() can be
called only after eth_device allocation and init, and hence
after priv area allocation, so dev->priv is correctly
initialized upon mcast() call.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Patch: 278990
There are several implementation issues for tsec_mcast_addr()
addressed by this patch:
* unmanaged, not portable r/w access to registers; fixed with
setbits_be32()/ clrbits_be32()
* use of volatile pointers
* unnecessary forced cast to u8 for the ether_crc() result
* removed redundant parens
* corrected some comment slips
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Patch: 279000
This fixes the following compiler warnings when activating
CONFIG_MCAST_TFTP:
tsec.c: In function 'tsec_mcast_addr':
tsec.c:130:2: warning: passing argument 2 of 'ether_crc' makes pointer
from integer without a cast [enabled by default]
In file included from /work/u-boot-net/include/common.h:874:0,
from tsec.c:15:
/work/u-boot-net/include/net.h:189:5: note: expected 'const unsigned
char *' but argument is of type 'u8'
tsec.c: In function 'tsec_initialize':
tsec.c:646:13: warning: assignment from incompatible pointer type
[enabled by default]
eth.c: In function 'eth_mcast_join':
eth.c:358:2: warning: passing argument 2 of 'eth_current->mcast' makes
integer from pointer without a cast [enabled by default]
eth.c:358:2: note: expected 'u32' but argument is of type 'u8 *'
In the eth_mcast_join() implementation, eth_current->mcast()
takes a u8 pointer to the multicast mac address and not a ip
address value as implied by its prototype.
Fix parameter type mismatch for tsec_macst_addr() (tsec.c):
ether_crc() takes a u8 pointer not a u8 value.
mcast() is given a u8 pointer to the multicats mac address.
Update parameter type for the rest of mcast() instances.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Patch: 278989
It's important that buffer descriptors are aligned in accordance to GMAC
data bus width (32/64/128-bit). It's safe to align to 128-bit (16-bytes)
for every bus width type.
If buffer descriptor is improperly aligned GMAC discards lower bits of
provided address and as a result reads from improper location that
doesn't match expected fields.
Commit ef76025a99 "net: Multiple
updates/enhancements to designware.c" introduced another structure
member "link_printed" right before buffer descriptors while "padding"
member was left untouched. This together with alignment of structure
itself to 16-byte boundary forces buffer descriptoprs always to be
4-byte aligned that causes driver complete disfunction if GMAC bus width
is 64 or 128-bit.
Proposed change makes sure all buffer descriptors are 16-byte (128-bit)
aligned.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Patch: 277902
"bus mode" register contains lots of fields and some of them don't
expect to be written with 0 (zero). So since we're only interested in
resetting MAC (which is done with setting the least significant bit of
this register with "0") I believe it's better to modify only 1 bit of
the register.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Vipin Kumar <vipin.kumar@st.com>
Patch: 277864
R8A7791 has the same sh-ether IP core as other SH/rmobile.
This patch adds support of R8A7791.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Joe Hershberger <joe.hershberger@gmail.com>
AR8035 driver will be never applied because of wrong mask for
AR8031 driver. Fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reported-by: Pavel Nakonechny <pavel.nakonechny@skitlab.ru>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Patch: 276944
This chip is compatible with other RTL8168 chips and can be found on the
NVIDIA Cardhu and Beaver boards.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Patch: 276475
currticks() is defined as get_timer(0), which returns an unsigned long,
so use %lu instead of %d to print the result.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Patch: 276473
The 'get_phy_driver' code in 'drivers/net/phy/phy.c' uses the following
method to determine which driver is to be loaded for a particular PHY
module:
list_for_each(entry, &phy_drivers) {
drv = list_entry(entry, struct phy_driver, list);
if ((drv->uid & drv->mask) == (phy_id & drv->mask))
return drv;
}
This means that a drv->mask of 0xfffff0 will return incorrect phy driver
for the logic above, even if the drv->uid is anything other than
something ending with a 0x0.
For e.g. if the RTL8211E drv->uid is 0x1cc915 and drv->mask is 0xffffff
and the RTL8211B drv->uid is 0x1cc910 and drv->mask is 0xffffff0, then
the phy driver selected will always be RTL8211B even though the
underlying phy connected on the board is a 8211E module.
This patch fixes this issue.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
This patch adds support for VSC8514 PHY module which can be
found on Freescale's T1040RDB boards.
Signed-off-by: Arpit Goel <B44344@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
R8A7790 has the same sh-ether IP core as other SH/rmobile.
This patch adds support of R8A7790.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
The sh-eth of rmobile needs to use invalidate_cache* function.
This patch adds invalidate_cache* function.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Patch: 268948
sh-eth can change the alignment size of a packet descriptor according to BUS
size. This patch adds this function.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
The cache API of SH was changed from dcache_wback_range to flush_dcache_range.
sh-eth uses dcache_wback_range. This patch changes to flush_dcache_range.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Avoid a recently introduced unused variable warning for boards that
use mvgbe but not phylib.
Signed-off-by: Sascha Silbe <t-uboot@infra-silbe.de>
Patch: 266334
As AR8031 and AR8033 have same PHY ID 0x4dd074, they use the
common driver. Currently AR8031_driver didn't work for AR8033,
hence updated it to have it work on AR8031/AR8033.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
The fec_halt() never free'd both RX and TX DMA descriptors that
were allocated in fec_init(), nor did it free the RX buffers.
Rework the FEC driver so that these descriptors and buffers are
allocated only once in fec_probe().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
T1040 Soc has four personalities:
-T1040 (4 cores with L2 switch)
-T1042:Reduced personality of T1040 without L2 switch
-T1020:Reduced personality of T1040 with less cores(2 cores)
-T1022:Reduced personality of T1040 with 2 cores and without L2 switch
Update defines in arch/powerpc header files, Makefiles and in
driver/net/fm/Makefile to support all T1040 personalities
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
[York Sun: fixed Makefiles]
Acked-by: York Sun <yorksun@freescale.com>
The MPC824x processors have long reached EOL, and the PN62 board has
not seen any board-specific updates for more than a decade. It is now
causing build issues. Instead of wasting time on things nobody is
interested in any more, we rather drop this board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
cc: Tom Rini <trini@ti.com>
Conflicts:
arch/arm/cpu/arm926ejs/mxs/Makefile
board/compulab/cm_t35/Makefile
board/corscience/tricorder/Makefile
board/ppcag/bg0900/Makefile
drivers/bootcount/Makefile
include/configs/omap4_common.h
include/configs/pdnb3.h
Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:
board/compulab/common/Makefile
board/udoo/Makefile
include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.
include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.
Note: 'git show' will also list two files just because
they are new:
include/configs/am335x_igep0033.h
include/configs/omap3_igep00x0.h
On relatively slow boards (such as the MIPS Malta with an FPGA core
card) it can be extremely common for transmits to underflow - to the
point where it appears they simply do not work at all. Setting the
NOUFLO bit causes the ethernet controller to not begin transmission on
the wire until a transmit start point is reached. Setting that transmit
start point to the full packet will cause the controller to only
transmit the packet once it has buffered it entirely thus preventing any
transmit underflows from occuring and allowing the controller to
function on slower boards.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Ensure that the view of memory from the CPU & the ethernet controller is
coherent at the various points where they exchange data. This prevents
stale data from being transmitted or received, and prevents the driver
from getting stuck waiting for the ethernet controller to update
descriptors when in reality it has but the old values are being read
from cache.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fix up the code to match Documentation/CodingStyle. This is mostly
removing extraneous spaces.
No functional change is intended.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Netconsole loses the second character when used as input by
either setenv stdin nc or setenv stdin serial,nc if using CONSOLE_CONSOLE_MUX
Before a nc_send_packet() to echo the input, a check is done to see if
nc_ether is valid. If its not, it waits for an arp request and then sends
the packet (which contains the first character of line to be displayed as
output). As part of reaping the arp request, the second character is consumed.
We protect this by making the call to NetLoop(NETCONS) between
input_recursion.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Get DMA bus width from design config register
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This can be useful if one wants to disable an interface in u-boot
because u-boot should not manage it but then later reenable it for FDT
fixing or if the kernel uses this interface.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: fix conflict in fm_eth.h]
Acked-by: York Sun <yorksun@freescale.com>
T1040QDS is a high-performance computing evaluation, development and
test platform supporting the T1040 QorIQ Power Architecture™ processor.
T1040QDS board Overview
-----------------------
- Four e5500 cores, each with a private 256 KB L2 cache
- 256 KB shared L3 CoreNet platform cache (CPC)
- Interconnect CoreNet platform
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
for the following functions:
- Packet parsing, classification, and distribution
- Queue management for scheduling, packet sequencing, and congestion
management
- Cryptography Acceleration
- RegEx Pattern Matching Acceleration
- IEEE Std 1588 support
- Hardware buffer management for buffer allocation and deallocation
- Ethernet interfaces
- Integrated 8-port Gigabit Ethernet switch
- Four 1 Gbps Ethernet controllers
- SERDES Connections, 8 lanes supporting:
— PCI Express: supporting Gen 1 and Gen 2;
— SGMII
— QSGMII
— SATA 2.0
— Aurora debug with dedicated connectors
- DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and
Interleaving
-IFC/Local Bus
- NAND flash: 8-bit, async, up to 2GB.
- NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB
- GASIC: Simple (minimal) target within Qixis FPGA
- PromJET rapid memory download support
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep
- QIXIS System Logic FPGA
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Power Supplies
- Video
- DIU supports video at up to 1280x1024x32bpp
- USB
- Supports two USB 2.0 ports with integrated PHYs
— Two type A ports with 5V@1.5A per port.
— Second port can be converted to OTG mini-AB
- SDHC
- SDHC port connects directly to an adapter card slot, featuring:
- Supporting SD slots for: SD, SDHC (1x, 4x, 8x) and/or MMC
— Supporting eMMC memory devices
- SPI
- On-board support of 3 different devices and sizes
- Other IO
- Two Serial ports
- ProfiBus port
- Four I2C ports
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: fix conflict in boards.cfg]
Acked-by-by: York Sun <yorksun@freescale.com>
Fix PHY addresses for QSGMII Riser Card working in
SGMII mode on board P3041/P5020/P4080/P5040/B4860.
QSGMII Riser Card can work in SGMII mode, but
having the different PHY addresses.
So the following steps should be done:
1. Confirm whether QSGMII Riser Card is used.
2. If yes, set the proper PHY address.
Generally, the function is_qsgmii_riser_card() is
for step 1, and set_sgmii_phy() for step 2.
However, there are still some special situations,
take P5040 and B4860 as examples, the PHY addresses
need to be changed when serdes protocol is changed,
so it is necessary to confirm the protocol before
setting PHY addresses.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
if phy_connect() did not find a phy, phydev is NULL and
following code in cpsw_phy_init() crashes. Fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Performing tftp transfers on mx28 results in random timeouts.
Hector Palacios and Robert Hodaszi analyzed the root cause being related to the
wrong alignment of the 'buff' buffer inside fec_recv().
Benoît Thébaudeau provided an excellent analysis of the alignment bug that is
present on older versions, such as GCC 4.5.4:
http://marc.info/?l=u-boot&m=137942904906131&w=2
Use ALLOC_CACHE_ALIGN_BUFFER() to avoid alignment issues from older GCC
versions.
Reported-by: Hector Palacios <hector.palacios@digi.com>
Tested-by: Oliver Metz <oliver@freetz.org>
Tested-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Similarly as mx25 and mx53, mx6solo-lite needs to setup the MII gasket for RMII
mode.
Add support for mx6solo-lite.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The SPDX License List version 1.19 now contains an official entry for
the IBM-pibs license. However, instead of our suggestion "ibm-pibs",
the SPDX License List uses "IBM-pibs", with the following rationale:
"The reason being that all other SPDX License List short identifiers
tend towards using capital letters unless spelling a word. I'd prefer
to be consistent to this end".
Change the license IDs to use the official name.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix various misspellings of things like "environment", "kernel",
"default" and "volatile", and throw in a couple grammar fixes.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
fix the following building warning
---8>---
macb.c: In function 'macb_init':
macb.c:400:14: warning: 'phydev' may be used uninitialized in this function
macb.c:377:21: note: 'phydev' was declared here
---<8---
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Without this change, the following message is generated:
Warning: FEC using MAC address from net device
See doc/README.enetaddr for details.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Also some fix for QSGMII.
1. fix QSGMII configure of Serdes2.
2. fix PHY address of QSGMII MAC9 & MAC10 for each FMAN.
3. fix dtb for QSGMII interface.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
This commit adapts the files that were derived from PIBS (PowerPC
Initialization and Boot Software) codeto using SPDX License
Identifiers.
So far, SPDX has not assigned an official License ID for the PIBS
license yet, so this should be considered preliminary.
Note that the following files contained incorrect license information:
arch/powerpc/cpu/ppc4xx/4xx_uart.c
arch/powerpc/cpu/ppc4xx/start.S
arch/powerpc/include/asm/ppc440.h
These files included, in addition to the GPL-2.0 / ibm-pibs dual
license as inherited from PIBS, a GPL-2.0+ license header which was
obviously incorrect. This has been removed.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Conflicts:
Licenses/README
Acked-by: Stefan Roese <sr@denx.de>
1. Reformat tx/rx descriptor as an uniform struct.
2. Replace uint32_t[2] with uint64_t for descriptor control.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Joe Hershberger <joe.hershberger@gmail.com>
This patch adds support for Realtek PHY modules RTL8211DN and
RTL8211E (variants: RTL8211E-VB-CG, RTL8211E-VL-CG, RTL8211EG-VB-CG),
which can be found on Freescale's T1040RDB boards.
To make the driver more generic across 8211 family, a generic name 8211x
is added for macros and function names.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Use ARRAY_SIZE instead of having similar implementation in each drivers.
The NUMELEMS defined in drivers/net/npe/include/IxOsalTypes.h is not used
at all, so this patch removes it instead of converting it to use ARRAY_SIZE.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: York Sun <yorksun@freescale.com>
Fixup an easy conflict over adding the clk_get prototype and USB_OTG
defines for am33xx having moved.
Conflicts:
arch/arm/include/asm/arch-am33xx/hardware.h
Signed-off-by: Tom Rini <trini@ti.com>
FMAN firmware can be in NOR flash, NAND flash, SPI flash, MMC or even
remote. In case none of them is defined, set it to null.
Signed-off-by: York Sun <yorksun@freescale.com>
accessing a lan9303 switch with the cpsw driver results in wrong
speed detection, as the switch sets the BMSR_ERCAP in BMSR
register, and follow read of the MII_STAT1000 register fails, as
the switch does not support it. Current code did not check,
if a phy_read() fails ... fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
BD ram address may vary in various SOC, so removing the hardcoding and
passing the same information through platform data
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
There is no reason to wait for the entire frame to start DMA on receive,
so enable rx cut-thru for better performance.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The pcnet driver uses the pci_phys_to_mem function
to get the memory address of the DMA buffers. This
This assumes an 1:1 mapping between the PCI and
physical memory which is not true on all platforms.
On MIPS platform U-Boot is running within a mapped
memory region, and the pci_phys_to_mem macro can't
be used to obtain the memory address of the buffers.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Commit de1d786e (add support for Xilinx 1000BASE-X phy (GTX)) introduced the
checking for ESTATUS_1000_XHALF, but it incorrectly sets the
SUPPORTED_1000baseX_Full flag in this case.
Set the SUPPORTED_1000baseX_Half flag instead.
Acked-by: Charles Coldwell <coldwell@gmail.com>
Reviewed-By: Sascha Silbe <t-uboot@infra-silbe.de>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
de1d786 [add support for Xilinx 1000BASE-X phy (GTX)] introduced a
check for the extended status register in order to support
1Gbps-capable PHYs that don't have the 1000BASE-T registers. Since
Extended Status only indicates what the PHY (i.e. the local side) is
capable of, this broke communication with non-1Gbps peers.
Only check the extended status if the 1000BASE-T registers are
actually missing so we don't end up setting speed to 1Gbps even though
the previous test (for the combination of local and peer support for
1Gbps) already indicated we can't do 1Gbps with the current peer.
Signed-off-by: Sascha Silbe <t-uboot@infra-silbe.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and
serial.
Conflicts:
arch/arm/dts/exynos5250.dtsi
Signed-off-by: Tom Rini <trini@ti.com>
The MX28 multi-layer AHB bus can be too slow and trigger the
FEC DMA too early, before all the data hit the DRAM. This patch
ensures the data are written in the RAM before the DMA starts.
Please see the comment in the patch for full details.
This patch was produced with an amazing help from Albert Aribaud,
who pointed out it can possibly be such a bus synchronisation
issue.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Remove incorrectly called and duplicate flush_dcache_range() call
from fec_mxc driver. The call is not needed, since the caches are
already flushed in fec_tbd_init(), moreover the second argument should
be the ending address, not size.
Signed-off-by: Marek Vasut <marex@denx.de>
Reported-by: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
add atheros ar803x phy, used on the upcoming siemens boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
add natsemi dp83630 phy, used on the upcoming siemens boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Using CONFIG_AT91FAMILY replace #ifdeferry for atmel SoC
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
The device interface is 16 bits wide.
All the available packets are read from the incoming fifo.
Signed-off-by: Roberto Cerati <roberto.cerati@bticino.it>
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
[voice.shen@atmel.com: address comments from review results]
[voice.shen@atmel.com: clean up for submit]
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
commit 39695029bc15041c809df3db4ba19bd729c447fa
Author: Charles Coldwell <coldwell@ll.mit.edu>
Date: Tue Feb 19 08:27:33 2013 -0500
Changes to support the Xilinx 1000BASE-X phy (GTX/MGT)
Signed-off-by: Charles Coldwell <coldwell@ll.mit.edu>
Add support for Micrel PHY KSZ9031 in phylib,
including small rework for KSZ9021 to avoid
code duplication
Signed-off-by: David Andrey <david.andrey@netmodule.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Joe Herschberger <joe.hershberger@gmail.com>
Cc: Andy Fleming <afleming@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
SPEAr310 and SPEAr320 Ethernet interfaces share same MDIO lines to control their
respective phys. Currently there is a fixed configuration in which only a
particular MAC can use the MDIO lines.
Call an arch specific function to take control of specific mdio lines at
runtime.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Marvell Dove also uses mvgbe as ethernet driver, therefore add support
for Dove to reuse the current driver.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This patch adds support for the WEMAC, the ethernet controller included
in the Allwinner A10 SoC. It will get used in the upcoming A10 board
support.
From: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
This patch adds FEC support for Vybrid VF610 platform.
In function fec_open(), RCR register is only set as RGMII mode. But RCR
register should be set as RMII mode for VF610 platform.
This configuration is already done in fec_reg_setup(), so this piece of
code could just leave untouched the FEC_RCNTRL_RGMII / FEC_RCNTRL_RMII /
FEC_RCNTRL_MII_MODE bits.
Signed-off-by: Alison Wang <b18965@freescale.com>
Reviewed-by: Benoit Thebaudeau <benoit.thebaudeau@advansee.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
- Added SERDES2 PRTCLs = 0x98, 0x9E
- Default Phy Addresses for Teranetics PHY on XAUI card
The PHY addresses of Teranetics PHY on XAUI riser card are assigned
based on the slot it is in. Switches SW4[2:4] and SW6[2:4] on
AMC2PEX-2S On B4860QDS, AMC2PEX card decide the PHY addresses on slot1
and slot2
- Configure MDIO for 10Gig Mac
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
TN80xx has same PHY ID as TN2020, but it needs different setting to register
30.93 which used to select line, so we read register 30.32 which has
bit 15:12 to indicate PHY hardware version, for TN20xx we will get 3 or 2,
for TN80xx we will get 5 or 4.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The VSC8574 is a quad-port Gigabit Ethernet transceiver with four SerDes
interfaces for quad-port dual media capability. This driver supports SGMII
and QSGMII MAC mode. For now SGMII mode is tested.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
- set proper compatible property name for mEMAC.
- fixed ft_fixup_port for dual-role mEMAC, which will lead to
MAC node disabled incorrectly.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T4160 SoC is low power version of T4240. The T4160 combines eight dual
threaded Power Architecture e6500 cores and two memory complexes (CoreNet
platform cache and DDR3 memory controller) with the same high-performance
datapath acceleration, networking, and peripheral bus interfaces.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
1. fix 10G mac offset by plus 8;
2. add second 10G port info for FM1 & FM2 when init ethernet info;
3. fix 10G lanes name to match lane protocol table;
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Adds an ET1011C PHY driver which is derived from the
Linux kernel PHY driver (drivers/net/phy/et1011c.c)
from the v3.9-rc2 tag. Note that an errata workaround
config option is implemented to allow for TX_CLK to be
enabled even when gigabit mode is negotiated. This
workaround is used on the PG1.0 TI814X EVM.
Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
TI814x's version 1 CPSW has a different slave_regs layout.
Add support for the differing registers.
Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Some legacy RGMII phys don't have in band signaling for the
speed information. so set the RGMII MAC mode according to
the speed got from PHY.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Reported-by: John Traill <john.traill@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Avoid overwriting GEMx_RCLK_CTRL and GEMx_CLK_CTRL
if the Ethernet interface is connect on EMIO
Do not enable emio for this standard board configuration for now.
Signed-off-by: David Andrey <david.andrey@netmodule.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Pass the PHY address to the driver init to
allow parallel use of both interfaces
Signed-off-by: David Andrey <david.andrey@netmodule.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
The whole driver used 100Mbps because of zc702 rev B.
Fix problem with not setup proper clock for gem1.
This is generic approach for clk setup.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
BDs can be correctly setup just once and init function
performs only phy autodetection and enabling RX/TX.
RX/TX are disabled in halt function.
This patch solves the problem with repeatable tftp transfers.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Removing this bit causes that frame is sent only once.
(With wrap big one packet has been sent several times
which dramatically decrease throughput)
TRM: (Table 16-3: Tx Buffer Descriptor Entry)
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
This phy is used on zedboard (xilinx zynq platform).
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
'bool' is defined in random places. This patch consolidates them into a
single header file include/linux/types.h, using stdbool.h introduced in C99.
All other #define, typedef and enum are removed. They are all consistent with
true = 1, false = 0.
Replace FALSE, False with false. Replace TRUE, True with true.
Skip *.py, *.php, lib/* files.
Signed-off-by: York Sun <yorksun@freescale.com>
- In arch/arm/cpu/armv7/omap-common/timer.c,
drivers/mtd/nand/omap_gpmc.c and drivers/net/cpsw.c add #include files
that the driver needs but had been relying on <config.h> to bring in.
- In arch/arm/cpu/armv7/omap-common/lowlevel_init.S add <config.h>
- In am335x_evm.h and pcm051.h don't globally include
<asm/arch/hardware.h> and <asm/arch/cpu.h> but just <asm/arch/omap.h>
as that is the only include which defines things the config uses.
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Tom Rini <trini@ti.com>
In master we had already taken a patch to fix the davinci GPIO code for
CONFIG_SOC_DM646X and in u-boot-ti we have additional patches to support
DA830 (which is CONFIG_SOC_DA8XX && !CONFIG_SOC_DA850). Resolve these
conflicts manually and comment the #else/#endif lines for clarity.
Conflicts:
arch/arm/include/asm/arch-davinci/gpio.h
drivers/gpio/da8xx_gpio.c
Signed-off-by: Tom Rini <trini@ti.com>
Before submitting packets to cpdma, phy status is updated on every packet
which leads to delay in packet send intern reduces the Ethernet performance.
Checking mdio status for each packet will reduce timetaken to send a packet
and there by increasing the Ethernet performance. With this the performance
is increased from 208KiB/s to 375KiB/s on EVMsk
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>