Read the boot arguments passed by cboot via the /chosen/bootargs
property and store it in the cbootargs environment variable.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This function will attempt to look up an Ethernet address in the DTB
that was passed in from cboot. It does so by first trying to locate the
default Ethernet device for the board (identified by the "ethernet"
alias) and if found, reads the "local-mac-address" property. If the
"ethernet" alias does not exist, or if it points to a device tree node
that doesn't exist, or if the device tree node that it points to does
not have a "local-mac-address" property or if the value is invalid, it
will fall back to the legacy mechanism of looking for the MAC address
stored in the "nvidia,ethernet-mac" or "nvidia,ether-mac" properties of
the "/chosen" node.
The MAC address is then written to the default Ethernet device for the
board (again identified by the "ethernet" alias) in U-Boot's control
DTB. This allows the device driver for that device to read the MAC
address from the standard location in device tree.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is easier to deal with and works just as well for this simple
function.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra186 build are currently dealt with in very special ways, which is
because Tegra186 is fundamentally different in many respects. It is no
longer necessary to do many of the low-level programming because early
boot firmware will already have taken care of it.
Unfortunately, separating Tegra186 builds from the rest in this way
makes it difficult to share code with prior generations of Tegra. With
all of the low-level programming code behind Kconfig guards, the build
for Tegra186 can again be unified.
As a side-effect, and partial reason for this change, other Tegra SoC
generations can now make use of the code that deals with taking over a
boot from earlier bootloaders. This used to be nvtboot, but has been
replaced by cboot nowadays. Rename the files and functions related to
this to avoid confusion. The implemented protocols are unchanged.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Resetting the USB device controller on boot is only necessary if the SoC
actually has a UDC controller and U-Boot enables support for it. All the
Tegra boards support UDC via the ChipIdea UDC driver, so make the UDC on
boot workaround depend on the ChipIdea UDC driver.
This prevents a crash on Tegra186 which does not have the ChipIdea UDC.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Some devices may restrict access to the PMC to TrustZone software only.
Non-TZ software can detect this and use SMC calls to the firmware that
runs in the TrustZone to perform accesses to PMC registers.
Note that this also fixes reset_cpu() and the enterrcm command on
Tegra186 where they were previously trying to access the PMC at a wrong
physical address.
Based on work by Kalyani Chidambaram <kalyanic@nvidia.com> and Tom
Warren <twarren@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The save_boot_params() function takes as its first four arguments the
first four registers. On 32-bit ARM these are r0, r1, r2 and r3, all of
which are 32 bits wide. However, on 64-bit ARM thene registers are x0,
x1, x2 and x3, all of which are 64 bits wide. In order to allow reusing
the save_boot_params() implementation on 64-bit ARM, change it to take
unsigned long parameters rather than the fixed size 32-bit integers.
This ensures that the correct values are passed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Powergate code is not relevant on all Tegra SoC generations, so guard it
with a Kconfig symbol that can be selected by the generations that need
it.
This is in preparation for unifying Tegra186 code with the code used on
older generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Pin controller code is not relevant on all Tegra SoC generations, so
guard it with a Kconfig symbol that can be selected by the generations
that need it.
This is in preparation for unifying Tegra186 code with the code used on
older generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Memory controller code is not relevant on all Tegra SoC generations, so
guard it with a Kconfig symbol that can be selected by the generations
that need it.
This is in preparation for unifying Tegra186 code with the code used on
older generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The GP pad control code is not relevant on all Tegra SoC generations, so
guard it with a Kconfig symbol that can be selected by the generations
that need it.
This is in preparation for unifying Tegra186 code with the code used on
older generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Clock code is not relevant on all Tegra SoC generations, so guard it
with a Kconfig symbol that can be selected by the generations that need
it.
This is in preparation for unifying Tegra186 code with the code used on
older generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There's no need to replicate the pmu.h header file for every Tegra SoC
generation. Use a single header that is shared across generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
pll_c is not a valid parent for the disp1 clock, so trying to set it
will fail. Given that display is not used in U-Boot, remove the init
table entry so that disp1 will keep its default parent (clk_m).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On Tegra210 the parents for the disp1 and disp2 clocks are slightly
different from earlier chips. Only pll_p, pll_d_out0, pll_d2_out0 and
clk_m are valid parents (technically pll_d_out is as well, but U-Boot
doesn't know anything about it). Fix up the type name and the mux
definition.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There are no more users of lowlevel_init.S. Remove the file.
Suggested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The commong initialization code manually initializes the GPIO
even when OF_CONTROL does it, so we can reduce the code size a
bit by not doing it manually when we have device tree support.
Using the omap3_logic board (dm3730), the sizes shrunk:
Before:
text data bss dec hex filename
561066 28596 116880 706542 ac7ee u-boot
55245 1605 1888 58738 e572 spl/u-boot-spl
After
text data bss dec hex filename
560898 28548 116872 706318 ac70e u-boot
55121 1557 1888 58566 e4c6 spl/u-boot-spl
Signed-off-by: Adam Ford <aford173@gmail.com>
With ipam390 support removed in we can remove the reference to the
linker script since that case will never be true.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
U-Boot README recommends initializing SDRAM in board_init_f(). DA850
was doing it as part of board_init_r() (through call to spl_board_init()
which calls arch_cpu_init() which calls da850_ddr_setup())
This worked fine till commit 15b8c75058 ("davinci:
da850evm/omapl138-lcdk: Move BSS to SDRAM because SRAM is full") moved
BSS to SDRAM.
Functions like mmc_initialize() called in board_init_r() assume BSS is
available. Since SDRAM was not initialized when arch/arm/lib/crt0.S tried
to initialize BSS to 0, BSS is not initialized correctly.
Fix this by simply calling arch_cpu_init() from board_init_f(). Also move
preloader_console_init() there to help debug issues with board_init_r().
With this spl_board_init() is no longer needed, we remove it.
Tested using MMC/SD boot on OMAP-L138 LCDK board.
Tested-by: Adam Ford <aford173@gmail.com> #da850evm
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Peter Howard <phoward@gme.net.au> #omapl138_lcdk
Extend the driver to build with DM_VIDEO enabled. DTS files
must additionally include 'u-boot,dm-pre-reloc' property in
soc and child nodes to enable driver binding to mxsfb device.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
In the UEFI Stall() boottime service we need access to usec_to_tick().
Export the function.
Remove redundant implementation in arch/arm/mach-rockchip/rk_timer.c.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This allows SPL to load the main U-Boot image from MMC once DM_MMC is
enabled.
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
- some fix for rk3399-puma;
- rockchip script make_fit_atf.py cleanup
- Enable TPL for rk3399 orangepi and nanopi4;
- add support for rk3399 boards: Nanopi NEO4, Rockpro64, Rock PI 4;
When using External PHY, reset the mux to use the external PHY in case U-Boot
was chainloaded from a misconfigured bootloader.
Fixes: 33e3378091 ("ARM: meson: rework soc arch file to prepare for new SoC")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The following DT nodes in the process on review for Linux 5.3,
until Linux 5.3 is tagged, add the missing DT nodes in u-boot specific
DTSI files that will be dropped when the v5.3-rc1 DT is synced again.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add initial support for Rock PI 4 board.
Specification
- Rockchip RK3399
- LPDDR4
- eMMC
- SD card slot
- RTL8211E 1Gbps
- HDMI In/Out, DP, MIPI DSI/CSI
- PCIe M.2
- USB 2.0, USB-3.0
- USB C Type
Commit details of rk3399-rock-pi-4.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: add ROCK Pi 4 DTS support"
(sha1: 1b5715c602fda7b812af0e190eddcce2812e5417)
Signed-off-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add initial support for Rockpro64 board.
Specification
- Rockchip RK3399
- 2/4GB Dual-Channel LPDDR3
- SD card slot
- eMMC socket
- 128Mb SPI Flash
- Gigabit ethernet
- PCIe 4X slot
- WiFI/BT module socket
- HDMI In/Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- DC 12V/2A
Commit details of rk3399-rockpro64.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: rockpro64 dts add usb regulator"
(sha1: 6db644c79c8d45d73b56bc389aebd85fc3679beb)
'Akash' has sent an initial patch before, so I keep him as board
maintainer and I'm co-maintainer based on our conversation.
Signed-off-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch cleans up make_fit_atf.py in the following way:
* Fix all issues reported by pylint
* Move copyright notice from file-to-generate to script
* Fix of-by-one bugs in loadables property
* Remove commented-out (dead) code.
Besides the bugfix no intended changes.
Tested on RK3399-Q7 with TF-A v2.1 as BL31.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK3399 SPL does not use a pinctrl driver to setup the UART pins.
Instead it works based on config macros, which set the base address
of the actual UART block.
Currently the RK3399 SPL support UART0 and UART2.
This patch adds UART3 in the same way as UART0.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds the missing GRF bit definitions for UART3 on the RK3399.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Heiko Schocher <hs@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
- Gen3 PCIe driver + enablement on Salvator-X platforms.
- Gen3 recovery SPL used to reload ATF/OpTee/U-Boot instead of minimon.
- SDHI HS400 fixes ported from latest BSP and datasheet.
Add a driver which supports transmitting digital sound to an audio codec.
This uses fixed parameters as a device-tree binding is not currently
defined.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a driver for the audio hub. This is modelled as a misc device which
supports writing audio data from I2S.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This function enables a peripheral clock and then immediately sets its
divider. Add a delay to allow the clock to settle first. This matches the
delay in other places which do a similar thing.
Without this, the I2S device on Nyan does not init properly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The first clock type appears to have and incorrect setting for out of the
mux outputs. It should be CLK_M, not OSC. Fix it and its only user.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Finding bitstream from cff-file is no longer valid after bitstream is built
into FIT image and loaded by generic firmware loader. Remove cff-file
as this is legacy implementation from A10 downstream.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
On SoCFPGA A10 systems, it can rarely happen that a reboot from Linux
will result in stale data in PL310 L2 cache controller. Even if the L2
cache controller is disabled via the CTRL register CTRL_EN bit, those
data can interfere with operation of devices using DMA, like e.g. the
DWMMC controller. This can in turn cause e.g. SPL to fail reading data
from SD/MMC.
The obvious solution here would be to fully reset the L2 cache controller
via the reset manager MPUMODRST L2 bit, however this causes bus hang even
if executed entirely from L1 I-cache to avoid generating any bus traffic
through the L2 cache controller.
This patch thus configures and enables the L2 cache controller very early
in the SPL boot process, clears the L2 cache and disables the L2 cache
controller again.
The reason for doing it in SPL is because we need to avoid accessing any
of the potentially stale data in the L2 cache, and we are certain any of
the stale data will be below the OCRAM address range. To further reduce
bus traffic during the L2 cache invalidation, we enable L1 I-cache and
run the invalidation code entirely out of the L1 I-cache.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Pull the PL310 clearing code into common code, so it can be reused
by Arria10.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Manage power supply configuration for board using stpmic1
with LPDDR2 or with LPDDR3:
+ VDD_DDR1 = 1.8V with BUCK3 (bypass if possible)
+ VDD_DDR2 = 1.2V with BUCK2
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Update DDR configuration with the latest update:
- PUBL_regs: DXnGCR[0]= according to ddr_width to disable Byte
lane 2/3 in 16bit
- fix LPDDR2/3 timing_calc to step RL/WL in relaxed
timings mode
- remove LPDDR3 RL3 (optional) support vs MR0[7]
because MR0[7] can't be read instead always apply
worse RL/WL for LPDDR3 when freq < 166MHz)
- change MR3 to 48ohm drive for LPDDR2/3
- change default ZPROG[7:4] = 0x1 for LPDDR2/3 ,
'0' is not allowed even when ODT not used
- use DQSTRN for LPDDR2/3 (it was not set in PIR)
- LPDDR3: set dqsge/dwsgx gate extension to 2,2
like LPDDR2
-DDRCTRL.dfitmg0:
+ for LPDDR3 tphy_wrlat = WL (as LPDDR2)
+ improvement for relaxed mode vs RL/Wl at corner case.
For example @533MHz RL/WL (relaxed) = 9/5 for LPDDR2/3
and correction to MR2 accordingly
- DDR_PCFGQOS1_1: port1 timeout relaxed from 0x00 to 0x40,
for LTDC.
- DDR_PCFGWQOS0_0: change vpr level from
11 to 12 in order to include the CPU on
the variable priority queue.
- DDR_SCHED: fix to consider 13 levels (13 levels - 1 = 0xC)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add the needed configurations for bootstage and
activate bootstage command.
BOOTSTAGE_REPORT is not activated by default.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
In initf_bootstage() we call bootstage_mark_name() which ends up calling
timer_get_us() before timer_init(); that cause crash for stm32mp1.
This patch solve the issue without changing the initialization sequence.
See also commit 97d20f69f5 ("Enable CONFIG_TIMER_EARLY with bootstage")
for other solution when DM is activated for TIMER.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Use SGI0 interruption and TAMP_BACKUP_MAGIC_NUMBER
to synchronize the core1 boot sequence requested by
core0 in psci_cpu_on():
- a initial interruption is needed in ROM code after
RCC_MP_GRSTCSETR_MPUP1RST (psci_cpu_off)
- the ROM code set to 0 the 2 registers
+ TAMP_BACKUP_BRANCH_ADDRESS
+ TAMP_BACKUP_MAGIC_NUMBER
when magic is not egual to
BOOT_API_A7_CORE0_MAGIC_NUMBER
This patch solve issue for cpu1 restart in kernel.
echo 0 > /sys/devices/system/cpu/cpu1/online
echo 1 > /sys/devices/system/cpu/cpu1/online
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch moves the the config SYS_MALLOC_LEN to
Kconfig as it is already done for zynq arch in
commit 01aa5b8f05 ("Kconfig: Move config
SYS_MALLOC_LEN to Kconfig for zynq")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
ENVL_NOWHERE is dependent on CONFIG_ENV_IS_NOWHERE and not on
CONFIG_CHAIN_OF_TRUST so return ENVL_NOWHERE when CONFIG_ENV_IS_NOWHERE
is enabled
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
LS1028A is an ARMv8 implementation. LS1028ARDB is an evaluation
platform that supports the LS1028A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The LX2160A PCIe is using driver PCIE_LAYERSCAPE_GEN4 instead
of PCIE_LAYERSCAPE.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The lx2160a have up to 6 PCIe controllers and have different
address and size of PCIe region.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The LS2080A has 8GB region for each PCIe controller, while the
other platforms have 32GB.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Change to use PCIe address macro to determine if precompile the PCIe
MMU table entry.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Build an SPL which can be started via SCIF download mode on R-Car Gen3
and allows loading and executing U-Boot uImage with the next stage code.
This is also useful for starting e.g. ATF BL2, which inits the hardware
and returns to the U-Boot SPL, which can then load e.g. U-Boot proper.
The H3, M3-W, M3-N SoCs have plenty of SRAM for storing the U-Boot SPL
while the payload, e.g. ATF BL2, executes, so there is no problem here.
However, E3 and D3 have much less SRAM, hence the loader uses a trick
where it copies itself beyond the area used by BL2 and executes from
there. That area is 32kiB large and not enough to hold U-Boot SPL, BSS,
stack and malloc area, so the later two are placed at +0x4000 offset
from start of SRAM, another area not used by ATF BL2. To make things
even more complicated, the SCIF loader cannot load to the upper 32kiB
of the SRAM directly, hence the copying approach.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
when loading the splash image from a FIT
- updates for loading internal and external splash data from FIT
- DM_GPIO/DM_VIDEO migration for mx53 cx9020 board
- fix boot issue on mx6sabresd board after DM_VIDEO migration
- increase the max preallocated framebuffer BPP to 32 in ipuv3
driver to prepare for configurations with higher color depth
- allow to use vidconsole_put_string() in board code for text
output on LCD displays
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXOK5Sw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXBvoAJ96YrInVKKWtuVigA9lNpk5xbmbeQCdG9wML4LI
dBbQyzD3mNqvnDMyNPQ=
=Plt7
-----END PGP SIGNATURE-----
Merge tag 'video-for-2019.07-rc3' of git://git.denx.de/u-boot-video
- update for using splashfile instead of location->name
when loading the splash image from a FIT
- updates for loading internal and external splash data from FIT
- DM_GPIO/DM_VIDEO migration for mx53 cx9020 board
- fix boot issue on mx6sabresd board after DM_VIDEO migration
- increase the max preallocated framebuffer BPP to 32 in ipuv3
driver to prepare for configurations with higher color depth
- allow to use vidconsole_put_string() in board code for text
output on LCD displays
Some H6 boards have a watchdog which didn't make the SoC
reboot properly.
Reason is still unknown but several people have test it.
Chen-Yu Tsai :
Pine H64 = H6 V200-AWIN H6448BA 7782 => OK
OrangePi Lite 2 = H6 V200-AWIN H8068BA 61C2 => KO
Martin Ayotte :
Pine H64 = H8069BA 6892 => OK
OrangePi 3 = HA047BA 69W2 => KO
OrangePi One Plus = H7310BA 6842 => KO
OrangePi Lite2 = H6448BA 6662 => KO
Clément Péron:
Beelink GS1 = H6 V200-AWIN H7309BA 6842 => KO
After the series of result, Icenowy try to reach Allwinner about this
issue but they seems not interested to investigate it.
As we don't have the ARIS coproc to do power management and watchdogis
the only solution to reset the board.
So, Change from watchdog to R_watchdog to allow a reboot on all H6
boards.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Meet the following boot hang.
"
U-Boot SPL 2019.04-00661-gdc80a012e4 (Apr 25 2019 - 10:31:57 +0800)
Trying to boot from MMC1
U-Boot 2019.04-00661-gdc80a012e4 (Apr 25 2019 - 10:31:57 +0800)
CPU: Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz)
CPU: Automotive temperature grade (-40C to 125C)Reset cause: POR
Model: Freescale i.MX6 Quad SABRE Smart Device Board
Board: MX6-SabreSD
I2C: ready
DRAM: 1 GiB
Video device 'ipu@2400000' cannot allocate frame buffer memory -ensure the device is set up before relocation
Error binding driver 'ipuv3_video': -28
Video device 'ipu@2800000' cannot allocate frame buffer memory -ensure the device is set up before relocation
Error binding driver 'ipuv3_video': -28
Some drivers failed to bind
Error binding driver 'generic_simple_bus': -28
Some drivers failed to bind
initcall sequence 4ffe4500 failed at call 1780dfb7 (err=-28)
"
1. fdtdec_get_alias_seq will use "video" as base, however in alias node,
we use ipux, so add new alias for U-Boot dts.
2. DM_VIDEO is enabled, however reserve_video is called before
relocation, so to make DM_VIDEO work before relocation, need to
set SYS_MALLOC_F_LEN
3. defconfig is updated with savedefconfig
Note: I do not have a video panel to test, but with this patch, U-Boot
boots up again, below log.
"
U-Boot SPL 2019.04-00662-g0b62453bff (Apr 25 2019 - 10:36:31 +0800)
Trying to boot from MMC1
U-Boot 2019.04-00662-g0b62453bff (Apr 25 2019 - 10:36:31 +0800)
CPU: Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz)
CPU: Automotive temperature grade (-40C to 125C) at 34C
Reset cause: POR
Model: Freescale i.MX6 Quad SABRE Smart Device Board
Board: MX6-SabreSD
I2C: ready
DRAM: 1 GiB
PMIC: PFUZE100 ID=0x10
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 3
Loading Environment from MMC... *** Warning - bad CRC, using default environment
PCI: pcie phy link never came up
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
The ipu node in imx53 is needed for DM_VIDEO. We also need to set
u-boot,dm-pre-reloc to initialize before relocation.
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Without this U-Boot specific property, booting on Armada XP theadorable
fails in SPL. All nodes in the "internal-regs" (simple-bus) DT node are
not scanned, so the UART node is missing (and others).
I'm not adding this property in an *u-boot.dtsi file, since there is
none matching the generic rules for all files including this dtsi
file. So to not miss any of the boards using this dtsi file, I'm
adding it to this file directly, which makes the Linux merge a less
easy unforunately.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chris Packham <judge.packham@gmail.com>
Cc: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
The watchdog should use a clock at 50 Mhz, so
instead of using the clock osc (200 Mhz), we
define a reference clock at 50Mhz and use it
for both watchdog.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The watchdog should use a clock at 50 Mhz, so
instead of using the clock osc (200 Mhz), we
define a reference clock at 50Mhz and use it
for both watchdog.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Stefan Roese <sr@denx.de>
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
CONFIG_SYS_[DI]CACHE_OFF had been partially converted to Kconfig
parameters; only for the ARC architecture. This patch turns these two
parameters into Kconfig items everywhere else they are found.
All of the include/configs/* and defconfig changes in this patch are
for arm machines only. The Kconfig changes for arc, nds32, riscv,
and xtensa have been included since these symbols are found in code
under arch/{arc,nds32,riscv,xtensa}, however, no currently-defined
include/configs/* or defconfigs for these architectures exist which
include these symbols.
These results have been confirmed with tools/moveconfig.py.
Acked-by: Alexey Brodkin <abrodkin@snopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Re-migrate for a few more boards]
Signed-off-by: Tom Rini <trini@konsulko.com>
According to De Morgan's Law[1]:
!(A && B) = !A || !B
!(A || B) = !A && !B
There are 5 places in the code where we find:
#if !(defined(CONFIG_SYS_ICACHE_OFF) && defined(CONFIG_SYS_DCACHE_OFF))
and 4 places in the code where we find:
#if (!defined(CONFIG_SYS_ICACHE_OFF) || !defined(CONFIG_SYS_DCACHE_OFF))
In words, the construct:
!defined(CONFIG_SYS_[DI]CACHE_OFF)
means:
"is the [DI]CACHE on?"
and the construct:
defined(CONFIG_SYS_[DI]CACHE_OFF)
means:
"is the [DI]CACHE off?"
Therefore
!(defined(CONFIG_SYS_ICACHE_OFF) && defined(CONFIG_SYS_DCACHE_OFF))
means:
"the opposite of 'are they both off?'"
in other words:
"are either or both on?"
and:
(!defined(CONFIG_SYS_ICACHE_OFF) || !defined(CONFIG_SYS_DCACHE_OFF)
means:
"are either or both on?"
As a result, I've converted the 4 instances of '(!A || !B)' to '!(A && B)' for
consistency.
[1] https://en.wikipedia.org/wiki/De_Morgan%27s_laws
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
Keep the FPGA bridge entries in SPL DT to let do_bridge_reset() toggle
the bridges on/off as needed according to the handoff file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Pull out the u-boot,dm-pre-reloc from socfpga_arria10_socdk_sdmmc_handoff.dtsi
into separate dtsi header file to make it easier to patch in custom handoff
dtsi files, without having to manually add the U-Boot bits. Shuffle the include
clauses in the A10 DT files to make it obvious what gets included where without
having to follow confusing long chain of includes, i.e. board DT file includes
everything it needs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Re-add support for Aries Embedded MCV SoM, which is CycloneV based
and the associated MCVEVK and MCVEVP baseboard. The board can boot
from eMMC. Ethernet and USB is supported.
The Aries Embedded boards have been removed with commit 03b54997d5
("board/aries: Remove"). I will now take care of them.
The device-tree files are from mainline Linux commit e93c9c99a629
("Linux v5.1)".
Signed-off-by: Wolfgang Grandegger <wg@aries-embedded.de>
CC: Marek Vasut <marex@denx.de>
CC: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The stratix 10 reset manager ad-hoc code in arch/arm contains an unused
function 'reset_deassert_peripherals_handoff' that has been added from
the beginning. As this is probably a result of copying the gen5 reset
manager and this function has never been used, remove it.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
commit c5de2b7eae ("arm: socfpga: implement proper peripheral reset")
has removed the call to 'reset_deassert_peripherals_handoff()' from
socfpga gen5 SPL since the reset driver now handles resets. However,
commit c1d4b464c8 ("ARM: socfpga: Disable bridges in SPL unless booting from FPGA")
has re-added this ad-hoc reset code, so that all peripherals were now
again enabled instead of letting the drivers enable them by request.
While at it, remove this function for gen5 as it should not be used.
Fixes: commit c1d4b464c8 ("ARM: socfpga: Disable bridges in SPL unless booting from FPGA")
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add support for loading FPGA bitstream to get DDR up running before
U-Boot is loaded into DDR. Boot device initialization, generic firmware
loader and SPL FAT support are required for this whole mechanism to work.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Add FPGA driver to support program FPGA with FPGA bitstream loading from
filesystem. The driver are designed based on generic firmware loader
framework. The driver can handle FPGA program operation from loading FPGA
bitstream in flash to memory and then to program FPGA.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
For chainboot configurations or test environments, this patch allows
booting barebox images by using command bootz.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Improvements and new features:
- split more rockchip pinctrl_core feature into per SoC
- enable TPL for evb-rk3399 board
- enable TPL/SPL for evb-px5 board
- enable TPL and OP-TEE support for evb-rk3229
- update fix in arm common assembly start code for rockchip header file
- update default SPL_FIT_GENERATOR for rockchip
- rk3399 boards update to use '-u-boot.dtsi'
- add new rk3399 boards: Nanopi M4, Nanopc T4
- enable sound for chromebook_minnie