mirror of
https://github.com/brain-hackers/u-boot-brain
synced 2024-06-09 23:36:03 +09:00
ARM: dts: sync Amlogic G12A DT with Linux 5.2-rc1
Sync from Linux commit a188339ca5a3 ("Linux 5.2-rc1")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This commit is contained in:
Neil Armstrong
parent
e2822ccc2c
commit
b1e81e67ee
|
|
@ -6,6 +6,8 @@
|
|||
/dts-v1/;
|
||||
|
||||
#include "meson-g12a.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/gpio/meson-g12a-gpio.h>
|
||||
|
||||
/ {
|
||||
compatible = "amlogic,u200", "amlogic,g12a";
|
||||
|
|
@ -21,9 +23,154 @@
|
|||
device_type = "memory";
|
||||
reg = <0x0 0x0 0x0 0x40000000>;
|
||||
};
|
||||
|
||||
cvbs-connector {
|
||||
compatible = "composite-video-connector";
|
||||
|
||||
port {
|
||||
cvbs_connector_in: endpoint {
|
||||
remote-endpoint = <&cvbs_vdac_out>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
flash_1v8: regulator-flash_1v8 {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "FLASH_1V8";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
vin-supply = <&vcc_3v3>;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
hdmi-connector {
|
||||
compatible = "hdmi-connector";
|
||||
type = "a";
|
||||
|
||||
port {
|
||||
hdmi_connector_in: endpoint {
|
||||
remote-endpoint = <&hdmi_tx_tmds_out>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
main_12v: regulator-main_12v {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "12V";
|
||||
regulator-min-microvolt = <12000000>;
|
||||
regulator-max-microvolt = <12000000>;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
vcc_1v8: regulator-vcc_1v8 {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "VCC_1V8";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
vin-supply = <&vcc_3v3>;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
vcc_3v3: regulator-vcc_3v3 {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "VCC_3V3";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
vin-supply = <&vddao_3v3>;
|
||||
regulator-always-on;
|
||||
/* FIXME: actually controlled by VDDCPU_B_EN */
|
||||
};
|
||||
|
||||
vcc_5v: regulator-vcc_5v {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "VCC_5V";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
vin-supply = <&main_12v>;
|
||||
|
||||
gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
|
||||
enable-active-high;
|
||||
};
|
||||
|
||||
usb_pwr_en: regulator-usb_pwr_en {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "USB_PWR_EN";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
vin-supply = <&vcc_5v>;
|
||||
|
||||
gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
|
||||
enable-active-high;
|
||||
};
|
||||
|
||||
vddao_1v8: regulator-vddao_1v8 {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "VDDAO_1V8";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
vin-supply = <&vddao_3v3>;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
vddao_3v3: regulator-vddao_3v3 {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "VDDAO_3V3";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
vin-supply = <&main_12v>;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
&cec_AO {
|
||||
pinctrl-0 = <&cec_ao_a_h_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "disabled";
|
||||
hdmi-phandle = <&hdmi_tx>;
|
||||
};
|
||||
|
||||
&cecb_AO {
|
||||
pinctrl-0 = <&cec_ao_b_h_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
hdmi-phandle = <&hdmi_tx>;
|
||||
};
|
||||
|
||||
&cvbs_vdac_port {
|
||||
cvbs_vdac_out: endpoint {
|
||||
remote-endpoint = <&cvbs_connector_in>;
|
||||
};
|
||||
};
|
||||
|
||||
&hdmi_tx {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
|
||||
pinctrl-names = "default";
|
||||
hdmi-supply = <&vcc_5v>;
|
||||
};
|
||||
|
||||
&hdmi_tx_tmds_port {
|
||||
hdmi_tx_tmds_out: endpoint {
|
||||
remote-endpoint = <&hdmi_connector_in>;
|
||||
};
|
||||
};
|
||||
|
||||
&uart_AO {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&uart_ao_a_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&usb {
|
||||
status = "okay";
|
||||
vbus-supply = <&usb_pwr_en>;
|
||||
};
|
||||
|
||||
&usb2_phy0 {
|
||||
phy-supply = <&vcc_5v>;
|
||||
};
|
||||
|
||||
&usb2_phy1 {
|
||||
phy-supply = <&vcc_5v>;
|
||||
};
|
||||
|
|
|
|||
|
|
@ -3,9 +3,13 @@
|
|||
* Copyright (c) 2018 Amlogic, Inc. All rights reserved.
|
||||
*/
|
||||
|
||||
#include <dt-bindings/phy/phy.h>
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/clock/g12a-clkc.h>
|
||||
#include <dt-bindings/clock/g12a-aoclkc.h>
|
||||
#include <dt-bindings/interrupt-controller/irq.h>
|
||||
#include <dt-bindings/interrupt-controller/arm-gic.h>
|
||||
#include <dt-bindings/reset/amlogic,meson-g12a-reset.h>
|
||||
|
||||
/ {
|
||||
compatible = "amlogic,g12a";
|
||||
|
|
@ -55,6 +59,14 @@
|
|||
};
|
||||
};
|
||||
|
||||
efuse: efuse {
|
||||
compatible = "amlogic,meson-gxbb-efuse";
|
||||
clocks = <&clkc CLKID_EFUSE>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
psci {
|
||||
compatible = "arm,psci-1.0";
|
||||
method = "smc";
|
||||
|
|
@ -70,6 +82,18 @@
|
|||
reg = <0x0 0x05000000 0x0 0x300000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
linux,cma {
|
||||
compatible = "shared-dma-pool";
|
||||
reusable;
|
||||
size = <0x0 0x10000000>;
|
||||
alignment = <0x0 0x400000>;
|
||||
linux,cma-default;
|
||||
};
|
||||
};
|
||||
|
||||
sm: secure-monitor {
|
||||
compatible = "amlogic,meson-gxbb-sm";
|
||||
};
|
||||
|
||||
soc {
|
||||
|
|
@ -85,12 +109,177 @@
|
|||
#size-cells = <2>;
|
||||
ranges = <0x0 0x0 0x0 0xff600000 0x0 0x200000>;
|
||||
|
||||
hdmi_tx: hdmi-tx@0 {
|
||||
compatible = "amlogic,meson-g12a-dw-hdmi";
|
||||
reg = <0x0 0x0 0x0 0x10000>;
|
||||
interrupts = <GIC_SPI 57 IRQ_TYPE_EDGE_RISING>;
|
||||
resets = <&reset RESET_HDMITX_CAPB3>,
|
||||
<&reset RESET_HDMITX_PHY>,
|
||||
<&reset RESET_HDMITX>;
|
||||
reset-names = "hdmitx_apb", "hdmitx", "hdmitx_phy";
|
||||
clocks = <&clkc CLKID_HDMI>,
|
||||
<&clkc CLKID_HTX_PCLK>,
|
||||
<&clkc CLKID_VPU_INTR>;
|
||||
clock-names = "isfr", "iahb", "venci";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "disabled";
|
||||
|
||||
/* VPU VENC Input */
|
||||
hdmi_tx_venc_port: port@0 {
|
||||
reg = <0>;
|
||||
|
||||
hdmi_tx_in: endpoint {
|
||||
remote-endpoint = <&hdmi_tx_out>;
|
||||
};
|
||||
};
|
||||
|
||||
/* TMDS Output */
|
||||
hdmi_tx_tmds_port: port@1 {
|
||||
reg = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
periphs: bus@34400 {
|
||||
compatible = "simple-bus";
|
||||
reg = <0x0 0x34400 0x0 0x400>;
|
||||
#address-cells = <2>;
|
||||
#size-cells = <2>;
|
||||
ranges = <0x0 0x0 0x0 0x34400 0x0 0x400>;
|
||||
|
||||
periphs_pinctrl: pinctrl@40 {
|
||||
compatible = "amlogic,meson-g12a-periphs-pinctrl";
|
||||
#address-cells = <2>;
|
||||
#size-cells = <2>;
|
||||
ranges;
|
||||
|
||||
gpio: bank@40 {
|
||||
reg = <0x0 0x40 0x0 0x4c>,
|
||||
<0x0 0xe8 0x0 0x18>,
|
||||
<0x0 0x120 0x0 0x18>,
|
||||
<0x0 0x2c0 0x0 0x40>,
|
||||
<0x0 0x340 0x0 0x1c>;
|
||||
reg-names = "gpio",
|
||||
"pull",
|
||||
"pull-enable",
|
||||
"mux",
|
||||
"ds";
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
gpio-ranges = <&periphs_pinctrl 0 0 86>;
|
||||
};
|
||||
|
||||
cec_ao_a_h_pins: cec_ao_a_h {
|
||||
mux {
|
||||
groups = "cec_ao_a_h";
|
||||
function = "cec_ao_a_h";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
cec_ao_b_h_pins: cec_ao_b_h {
|
||||
mux {
|
||||
groups = "cec_ao_b_h";
|
||||
function = "cec_ao_b_h";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
hdmitx_ddc_pins: hdmitx_ddc {
|
||||
mux {
|
||||
groups = "hdmitx_sda",
|
||||
"hdmitx_sck";
|
||||
function = "hdmitx";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
hdmitx_hpd_pins: hdmitx_hpd {
|
||||
mux {
|
||||
groups = "hdmitx_hpd_in";
|
||||
function = "hdmitx";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
uart_a_pins: uart-a {
|
||||
mux {
|
||||
groups = "uart_a_tx",
|
||||
"uart_a_rx";
|
||||
function = "uart_a";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
uart_a_cts_rts_pins: uart-a-cts-rts {
|
||||
mux {
|
||||
groups = "uart_a_cts",
|
||||
"uart_a_rts";
|
||||
function = "uart_a";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
uart_b_pins: uart-b {
|
||||
mux {
|
||||
groups = "uart_b_tx",
|
||||
"uart_b_rx";
|
||||
function = "uart_b";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
uart_c_pins: uart-c {
|
||||
mux {
|
||||
groups = "uart_c_tx",
|
||||
"uart_c_rx";
|
||||
function = "uart_c";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
uart_c_cts_rts_pins: uart-c-cts-rts {
|
||||
mux {
|
||||
groups = "uart_c_cts",
|
||||
"uart_c_rts";
|
||||
function = "uart_c";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
usb2_phy0: phy@36000 {
|
||||
compatible = "amlogic,g12a-usb2-phy";
|
||||
reg = <0x0 0x36000 0x0 0x2000>;
|
||||
clocks = <&xtal>;
|
||||
clock-names = "xtal";
|
||||
resets = <&reset RESET_USB_PHY20>;
|
||||
reset-names = "phy";
|
||||
#phy-cells = <0>;
|
||||
};
|
||||
|
||||
dmc: bus@38000 {
|
||||
compatible = "simple-bus";
|
||||
reg = <0x0 0x38000 0x0 0x400>;
|
||||
#address-cells = <2>;
|
||||
#size-cells = <2>;
|
||||
ranges = <0x0 0x0 0x0 0x38000 0x0 0x400>;
|
||||
|
||||
canvas: video-lut@48 {
|
||||
compatible = "amlogic,canvas";
|
||||
reg = <0x0 0x48 0x0 0x14>;
|
||||
};
|
||||
};
|
||||
|
||||
usb2_phy1: phy@3a000 {
|
||||
compatible = "amlogic,g12a-usb2-phy";
|
||||
reg = <0x0 0x3a000 0x0 0x2000>;
|
||||
clocks = <&xtal>;
|
||||
clock-names = "xtal";
|
||||
resets = <&reset RESET_USB_PHY21>;
|
||||
reset-names = "phy";
|
||||
#phy-cells = <0>;
|
||||
};
|
||||
|
||||
hiu: bus@3c000 {
|
||||
|
|
@ -113,6 +302,18 @@
|
|||
};
|
||||
};
|
||||
};
|
||||
|
||||
usb3_pcie_phy: phy@46000 {
|
||||
compatible = "amlogic,g12a-usb3-pcie-phy";
|
||||
reg = <0x0 0x46000 0x0 0x2000>;
|
||||
clocks = <&clkc CLKID_PCIE_PLL>;
|
||||
clock-names = "ref_clk";
|
||||
resets = <&reset RESET_PCIE_PHY>;
|
||||
reset-names = "phy";
|
||||
assigned-clocks = <&clkc CLKID_PCIE_PLL>;
|
||||
assigned-clock-rates = <100000000>;
|
||||
#phy-cells = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
aobus: bus@ff800000 {
|
||||
|
|
@ -122,6 +323,128 @@
|
|||
#size-cells = <2>;
|
||||
ranges = <0x0 0x0 0x0 0xff800000 0x0 0x100000>;
|
||||
|
||||
rti: sys-ctrl@0 {
|
||||
compatible = "amlogic,meson-gx-ao-sysctrl",
|
||||
"simple-mfd", "syscon";
|
||||
reg = <0x0 0x0 0x0 0x100>;
|
||||
#address-cells = <2>;
|
||||
#size-cells = <2>;
|
||||
ranges = <0x0 0x0 0x0 0x0 0x0 0x100>;
|
||||
|
||||
clkc_AO: clock-controller {
|
||||
compatible = "amlogic,meson-g12a-aoclkc";
|
||||
#clock-cells = <1>;
|
||||
#reset-cells = <1>;
|
||||
clocks = <&xtal>, <&clkc CLKID_CLK81>;
|
||||
clock-names = "xtal", "mpeg-clk";
|
||||
};
|
||||
|
||||
pwrc_vpu: power-controller-vpu {
|
||||
compatible = "amlogic,meson-g12a-pwrc-vpu";
|
||||
#power-domain-cells = <0>;
|
||||
amlogic,hhi-sysctrl = <&hhi>;
|
||||
resets = <&reset RESET_VIU>,
|
||||
<&reset RESET_VENC>,
|
||||
<&reset RESET_VCBUS>,
|
||||
<&reset RESET_BT656>,
|
||||
<&reset RESET_RDMA>,
|
||||
<&reset RESET_VENCI>,
|
||||
<&reset RESET_VENCP>,
|
||||
<&reset RESET_VDAC>,
|
||||
<&reset RESET_VDI6>,
|
||||
<&reset RESET_VENCL>,
|
||||
<&reset RESET_VID_LOCK>;
|
||||
clocks = <&clkc CLKID_VPU>,
|
||||
<&clkc CLKID_VAPB>;
|
||||
clock-names = "vpu", "vapb";
|
||||
/*
|
||||
* VPU clocking is provided by two identical clock paths
|
||||
* VPU_0 and VPU_1 muxed to a single clock by a glitch
|
||||
* free mux to safely change frequency while running.
|
||||
* Same for VAPB but with a final gate after the glitch free mux.
|
||||
*/
|
||||
assigned-clocks = <&clkc CLKID_VPU_0_SEL>,
|
||||
<&clkc CLKID_VPU_0>,
|
||||
<&clkc CLKID_VPU>, /* Glitch free mux */
|
||||
<&clkc CLKID_VAPB_0_SEL>,
|
||||
<&clkc CLKID_VAPB_0>,
|
||||
<&clkc CLKID_VAPB_SEL>; /* Glitch free mux */
|
||||
assigned-clock-parents = <&clkc CLKID_FCLK_DIV3>,
|
||||
<0>, /* Do Nothing */
|
||||
<&clkc CLKID_VPU_0>,
|
||||
<&clkc CLKID_FCLK_DIV4>,
|
||||
<0>, /* Do Nothing */
|
||||
<&clkc CLKID_VAPB_0>;
|
||||
assigned-clock-rates = <0>, /* Do Nothing */
|
||||
<666666666>,
|
||||
<0>, /* Do Nothing */
|
||||
<0>, /* Do Nothing */
|
||||
<250000000>,
|
||||
<0>; /* Do Nothing */
|
||||
};
|
||||
|
||||
ao_pinctrl: pinctrl@14 {
|
||||
compatible = "amlogic,meson-g12a-aobus-pinctrl";
|
||||
#address-cells = <2>;
|
||||
#size-cells = <2>;
|
||||
ranges;
|
||||
|
||||
gpio_ao: bank@14 {
|
||||
reg = <0x0 0x14 0x0 0x8>,
|
||||
<0x0 0x1c 0x0 0x8>,
|
||||
<0x0 0x24 0x0 0x14>;
|
||||
reg-names = "mux",
|
||||
"ds",
|
||||
"gpio";
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
gpio-ranges = <&ao_pinctrl 0 0 15>;
|
||||
};
|
||||
|
||||
uart_ao_a_pins: uart-a-ao {
|
||||
mux {
|
||||
groups = "uart_ao_a_tx",
|
||||
"uart_ao_a_rx";
|
||||
function = "uart_ao_a";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
uart_ao_a_cts_rts_pins: uart-ao-a-cts-rts {
|
||||
mux {
|
||||
groups = "uart_ao_a_cts",
|
||||
"uart_ao_a_rts";
|
||||
function = "uart_ao_a";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
cec_AO: cec@100 {
|
||||
compatible = "amlogic,meson-gx-ao-cec";
|
||||
reg = <0x0 0x00100 0x0 0x14>;
|
||||
interrupts = <GIC_SPI 199 IRQ_TYPE_EDGE_RISING>;
|
||||
clocks = <&clkc_AO CLKID_AO_CEC>;
|
||||
clock-names = "core";
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
sec_AO: ao-secure@140 {
|
||||
compatible = "amlogic,meson-gx-ao-secure", "syscon";
|
||||
reg = <0x0 0x140 0x0 0x140>;
|
||||
amlogic,has-chip-id;
|
||||
};
|
||||
|
||||
cecb_AO: cec@280 {
|
||||
compatible = "amlogic,meson-g12a-ao-cec";
|
||||
reg = <0x0 0x00280 0x0 0x1c>;
|
||||
interrupts = <GIC_SPI 203 IRQ_TYPE_EDGE_RISING>;
|
||||
clocks = <&clkc_AO CLKID_AO_CTS_OSCIN>;
|
||||
clock-names = "oscin";
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
uart_AO: serial@3000 {
|
||||
compatible = "amlogic,meson-gx-uart",
|
||||
"amlogic,meson-ao-uart";
|
||||
|
|
@ -141,6 +464,46 @@
|
|||
clock-names = "xtal", "pclk", "baud";
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
saradc: adc@9000 {
|
||||
compatible = "amlogic,meson-g12a-saradc",
|
||||
"amlogic,meson-saradc";
|
||||
reg = <0x0 0x9000 0x0 0x48>;
|
||||
#io-channel-cells = <1>;
|
||||
interrupts = <GIC_SPI 200 IRQ_TYPE_EDGE_RISING>;
|
||||
clocks = <&xtal>,
|
||||
<&clkc_AO CLKID_AO_SAR_ADC>,
|
||||
<&clkc_AO CLKID_AO_SAR_ADC_CLK>,
|
||||
<&clkc_AO CLKID_AO_SAR_ADC_SEL>;
|
||||
clock-names = "clkin", "core", "adc_clk", "adc_sel";
|
||||
status = "disabled";
|
||||
};
|
||||
};
|
||||
|
||||
vpu: vpu@ff900000 {
|
||||
compatible = "amlogic,meson-g12a-vpu";
|
||||
reg = <0x0 0xff900000 0x0 0x100000>,
|
||||
<0x0 0xff63c000 0x0 0x1000>;
|
||||
reg-names = "vpu", "hhi";
|
||||
interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
amlogic,canvas = <&canvas>;
|
||||
power-domains = <&pwrc_vpu>;
|
||||
|
||||
/* CVBS VDAC output port */
|
||||
cvbs_vdac_port: port@0 {
|
||||
reg = <0>;
|
||||
};
|
||||
|
||||
/* HDMI-TX output port */
|
||||
hdmi_tx_port: port@1 {
|
||||
reg = <1>;
|
||||
|
||||
hdmi_tx_out: endpoint {
|
||||
remote-endpoint = <&hdmi_tx_in>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
gic: interrupt-controller@ffc01000 {
|
||||
|
|
@ -163,10 +526,112 @@
|
|||
#size-cells = <2>;
|
||||
ranges = <0x0 0x0 0x0 0xffd00000 0x0 0x100000>;
|
||||
|
||||
reset: reset-controller@1004 {
|
||||
compatible = "amlogic,meson-g12a-reset",
|
||||
"amlogic,meson-axg-reset";
|
||||
reg = <0x0 0x1004 0x0 0x9c>;
|
||||
#reset-cells = <1>;
|
||||
};
|
||||
|
||||
clk_msr: clock-measure@18000 {
|
||||
compatible = "amlogic,meson-g12a-clk-measure";
|
||||
reg = <0x0 0x18000 0x0 0x10>;
|
||||
};
|
||||
|
||||
uart_C: serial@22000 {
|
||||
compatible = "amlogic,meson-gx-uart";
|
||||
reg = <0x0 0x22000 0x0 0x18>;
|
||||
interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
|
||||
clocks = <&xtal>, <&clkc CLKID_UART2>, <&xtal>;
|
||||
clock-names = "xtal", "pclk", "baud";
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
uart_B: serial@23000 {
|
||||
compatible = "amlogic,meson-gx-uart";
|
||||
reg = <0x0 0x23000 0x0 0x18>;
|
||||
interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
|
||||
clocks = <&xtal>, <&clkc CLKID_UART1>, <&xtal>;
|
||||
clock-names = "xtal", "pclk", "baud";
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
uart_A: serial@24000 {
|
||||
compatible = "amlogic,meson-gx-uart";
|
||||
reg = <0x0 0x24000 0x0 0x18>;
|
||||
interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
|
||||
clocks = <&xtal>, <&clkc CLKID_UART0>, <&xtal>;
|
||||
clock-names = "xtal", "pclk", "baud";
|
||||
status = "disabled";
|
||||
};
|
||||
};
|
||||
|
||||
usb: usb@ffe09000 {
|
||||
status = "disabled";
|
||||
compatible = "amlogic,meson-g12a-usb-ctrl";
|
||||
reg = <0x0 0xffe09000 0x0 0xa0>;
|
||||
interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
|
||||
#address-cells = <2>;
|
||||
#size-cells = <2>;
|
||||
ranges;
|
||||
|
||||
clocks = <&clkc CLKID_USB>;
|
||||
resets = <&reset RESET_USB>;
|
||||
|
||||
dr_mode = "otg";
|
||||
|
||||
phys = <&usb2_phy0>, <&usb2_phy1>,
|
||||
<&usb3_pcie_phy PHY_TYPE_USB3>;
|
||||
phy-names = "usb2-phy0", "usb2-phy1", "usb3-phy0";
|
||||
|
||||
dwc2: usb@ff400000 {
|
||||
compatible = "amlogic,meson-g12a-usb", "snps,dwc2";
|
||||
reg = <0x0 0xff400000 0x0 0x40000>;
|
||||
interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
|
||||
clocks = <&clkc CLKID_USB1_DDR_BRIDGE>;
|
||||
clock-names = "ddr";
|
||||
phys = <&usb2_phy1>;
|
||||
dr_mode = "peripheral";
|
||||
g-rx-fifo-size = <192>;
|
||||
g-np-tx-fifo-size = <128>;
|
||||
g-tx-fifo-size = <128 128 16 16 16>;
|
||||
};
|
||||
|
||||
dwc3: usb@ff500000 {
|
||||
compatible = "snps,dwc3";
|
||||
reg = <0x0 0xff500000 0x0 0x100000>;
|
||||
interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
|
||||
dr_mode = "host";
|
||||
snps,dis_u2_susphy_quirk;
|
||||
snps,quirk-frame-length-adjustment;
|
||||
};
|
||||
};
|
||||
|
||||
mali: gpu@ffe40000 {
|
||||
compatible = "amlogic,meson-g12a-mali", "arm,mali-bifrost";
|
||||
reg = <0x0 0xffe40000 0x0 0x40000>;
|
||||
interrupt-parent = <&gic>;
|
||||
interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
|
||||
interrupt-names = "gpu", "mmu", "job";
|
||||
clocks = <&clkc CLKID_MALI>;
|
||||
resets = <&reset RESET_DVALIN_CAPB3>, <&reset RESET_DVALIN>;
|
||||
|
||||
/*
|
||||
* Mali clocking is provided by two identical clock paths
|
||||
* MALI_0 and MALI_1 muxed to a single clock by a glitch
|
||||
* free mux to safely change frequency while running.
|
||||
*/
|
||||
assigned-clocks = <&clkc CLKID_MALI_0_SEL>,
|
||||
<&clkc CLKID_MALI_0>,
|
||||
<&clkc CLKID_MALI>; /* Glitch free mux */
|
||||
assigned-clock-parents = <&clkc CLKID_FCLK_DIV2P5>,
|
||||
<0>, /* Do Nothing */
|
||||
<&clkc CLKID_MALI_0>;
|
||||
assigned-clock-rates = <0>, /* Do Nothing */
|
||||
<800000000>,
|
||||
<0>; /* Do Nothing */
|
||||
};
|
||||
};
|
||||
|
||||
|
|
|
|||
|
|
@ -26,7 +26,9 @@
|
|||
#define CLKID_AO_M4_FCLK 13
|
||||
#define CLKID_AO_M4_HCLK 14
|
||||
#define CLKID_AO_CLK81 15
|
||||
#define CLKID_AO_SAR_ADC_SEL 16
|
||||
#define CLKID_AO_SAR_ADC_CLK 18
|
||||
#define CLKID_AO_CTS_OSCIN 19
|
||||
#define CLKID_AO_32K 23
|
||||
#define CLKID_AO_CEC 27
|
||||
#define CLKID_AO_CTS_RTC_OSCIN 28
|
||||
|
|
|
|||
|
|
@ -131,5 +131,10 @@
|
|||
#define CLKID_MALI_1 174
|
||||
#define CLKID_MALI 175
|
||||
#define CLKID_MPLL_5OM 177
|
||||
#define CLKID_CPU_CLK 187
|
||||
#define CLKID_PCIE_PLL 201
|
||||
#define CLKID_VDEC_1 204
|
||||
#define CLKID_VDEC_HEVC 207
|
||||
#define CLKID_VDEC_HEVCF 210
|
||||
|
||||
#endif /* __G12A_CLKC_H */
|
||||
|
|
|
|||
|
|
@ -51,7 +51,10 @@
|
|||
#define RESET_SD_EMMC_A 44
|
||||
#define RESET_SD_EMMC_B 45
|
||||
#define RESET_SD_EMMC_C 46
|
||||
/* 47-60 */
|
||||
/* 47 */
|
||||
#define RESET_USB_PHY20 48
|
||||
#define RESET_USB_PHY21 49
|
||||
/* 50-60 */
|
||||
#define RESET_AUDIO_CODEC 61
|
||||
/* 62-63 */
|
||||
/* RESET2 */
|
||||
|
|
|
|||
Loading…
Reference in New Issue
Block a user