Instead of using single fixed value for the calibration offset,
add tables which dynamically adjust this per calibration code
from the SCC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Some of the tuning taps produce suboptimal results. Add code
which skips those "bad" taps.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Check SCC for errors after check command if applicable and
optionally adjust the bus skew settings accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Disable the auto-retuning in HS400 mode in favor of manual calibration.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Adjust the TMPPORT3 offsets according to the latest information
from the chip vendor.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Adjust the DT2FF offsets in HS400 according to latest information
from the chip vendor.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The M3W up to ES1.2 uses 4 tuning taps for HS400, make it so.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Retain the SMPCMP value from last calibration in private data.
This will be later used for skipping bad taps.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Retain the tap number from last calibration in private data. This
will be later used for SCC error checking after each command.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch is to get clock directly from global data.
- Remove uclass clk api method. This was what i.MX platforms were
using, while QorIQ platforms weren't.
- Get clock only from global data, dropping mxc_get_clock().
QorIQ eSDHC controllers on one silicon use same reference clock.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
- fix boot banner on RPi3/4
- add support for one binary on RPi3/4
-----BEGIN PGP SIGNATURE-----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=4Z+A
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2020.01' of https://github.com/mbgg/u-boot
- add RPi4 upstream compatible to pinctrl
- fix boot banner on RPi3/4
- add support for one binary on RPi3/4
Allow the unit test to pass full 8 byte scan code sequences to the USB
keyboard emulation driver and to parse multi-byte escape sequences.
The following features are not yet tested:
* LED status
* caps-lock
* num-lock
* numerical pad keys
The following features are not yet implemented by the USB keyboard
driver and therefore not tested:
* modifiers for non-alpha-numeric keys, e.g. <SHIFT><TAB> and <ALT><F4>
* some special keys, e.g. <PRINT>
* some modifiers, e.g. <ALT> and <META>
* alternative keyboard layouts
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Provide support for F1-F12, Insert, Delete, Home, End, Page Up, Page Down.
As this leads to a size increase provide a customizing setting
CONFIG_USB_KEYBOARD_FN_KEYS.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Commit ec3dcea744 ("video: mxsfb: Configure the clock after eLCDIF reset")
causes boot regression on imx7d-pico/imx7d-sdb boards, so revert it
until a better solution is prepared.
This reverts commit ec3dcea744.
Reported-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
U-Boot support on Raspberry Pi 4 relies on the device-tree
provided by the firmware. The blob does not contain the
U-Boot specific pre-loc-rel properties. The result is, that
the U-Boot banner is not printed.
We fix this by setting the DM_FLAG_PRE_RELOC flag in the driver,
if we rely on a device-tree provided by the firmware.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The Raspberry Pi 4 upstream kernel device tree instroduces
a new compatible for the pinctroller. Add this to the driver
so that we can boot with the upstream kernel DT.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
- Clean vid/pid in Kconfig and add fastboot for rk3399
- add 'u-boot, spl-fifo-mode' for mmc
- Use FIT generator for rk3229 optee and rk3368 ATF
- fan53555: add support for Silergy SYR82X and SYR83X
Rockchips dwmmc controllers can't do dma to non-ddr addresses,
like for example the soc-internal sram but during boot parts of
TrustedFirmware need to be placed there from the read FIT image.
So add handling for a u-boot,spl-fifo-mode to not put the mmc
controllers into fifo mode for all time.
The regular fifo-mode property still takes precedent and only
if not set do we check for the spl-specific property.
Suggested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add 0x330c for rk3399 gadget product number.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
U-Boot has two different variants of dwc3 initializations,
- with dm variant gadget, so the respective dm driver would
call the dwc3_init in core.
- with non-dm variant gadget, so the usage board file would
call dwc3_uboot_init in core.
The driver probe would handle all respective gadget properties
including phy interface via phy_type property and then trigger
dwc3_init for dm-variant gadgets.
So, to support the phy interface for non-dm variant gadgets,
the better option is dwc3_uboot_init since there is no
dedicated controller for non-dm variant gadgets.
This patch support for adding phy interface like 8/16-bit UTMI+
code for dwc3_uboot.
This change used Linux phy.h enum list, to make proper code
compatibility.
Cc: Marek Vasut <marex@denx.de>
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Technically the default mmc device for fastboot would
use eMMC if the board support for it.
Rockchip platform access device 0 for eMMC so, use the
same device number for rk3328.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Select CONFIG_FASTBOOT_FLASH, CONFIG_FASTBOOT_FLASH_MMC_DEV
for rockchip SoC plaforms in fastboot Kconfig file instead
of defined it in board defconfig.
This eventually drop the explicit configs defined in
supporting board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add 0x310c for rk3128 gadget product number.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip support differnet or common gadget product number
between Rockchip SoCs like,
0x310a - rk3036
0x320a - rk3229, rk3288
0x330a - rk3328
So, select them on Kconfig based on platform specific
config defined.
This eventually drop the explicit configs defined in
supporting board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Gadget vendor number, 0x2207 is common across all platfroms
supported in Rockchip SoC.
So, select the same number globally, if ARCH_ROCKCHIP.
This eventually drop the explicit configs defined in supported
board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Select the gadget manufacturer as 'Rockchip' for
all rockchip platform SoC's.
This eventually drop the explicit defined added
on supported board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
fan53555_regulator_set_value() passes its own dev to pmic_clrsetbits()
instead of its parent (pmic). As result u-boot crashes when you try to
set voltage on fan53555 regulator
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
That's not correct and it breaks SMBUS-style reads and and writes for
some chips (e.g. SYR82X/SYR83X).
Stop bit should be sent only after the last message.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
SYR82X and SYR83X are almost identical to FAN53555, the only difference
is different die ID and revision, voltage ranges and steps.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Since upgrading to gcc9, warnings are issued:
"taking address of packed member of ‘...’ may result in an unaligned
pointer value"
Fix this by converting dwc2_fifo_read to use unaligned access since packed
structures may be on an unaligned address, depending on USB hardware.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Since upgrading to gcc9, warnings are issued:
"taking address of packed member of ‘...’ may result in an unaligned
pointer value"
Fix this by converting two functions to use unaligned access since packed
structures may be on an unaligned address, depending on USB hardware.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
To use this DM timer on socfpga as system tick, it needs to take itself
out of reset.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Make the function pointer struct const, as it does not need to be
writable. This doesn't really change anything other than moving this
variable to a different section. No functional change.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
We only need to build and link input.o when we have any of
CONFIG_KEYBOARD, CONFIG_DM_KEYBOARD (and SPL/TPL variants) or
CONFIG_TEGRA_KEYBOARD set.
Signed-off-by: Tom Rini <trini@konsulko.com>
xhci.h has now been moved to include/usb/ directory. Therefore, update the
path in the Cadence USB drivers.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add DM support for Silicon(SIL3131 / SIL3132 / SIL3124) sata driver as
few of the PowerPC platforms such as P series based boards need to
use SATA_SIL with DM,
Also fix below warning while PowerPC P series boards compilation,
===================== WARNING ======================"
This board does use CONFIG_LIBATA but has CONFIG_AHCI not"
enabled. Please update the storage controller driver to use"
CONFIG_AHCI before the v2019.07 release."
Failure to update by the deadline may result in board removal."
See doc/driver-model/MIGRATION.txt for more info."
===================================================="
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add DM support for Freescale PowerPC sata driver used for PowerPC T series
SoCs,
CONFIG_BLK needs to be enabled on these platforms. It adds the SATA
controller as AHCI device, which is strictly speaking not correct,
as the controller is not AHCI compatible, But the U-Boot AHCI uclass
interface enables the usage of this DM driver,
Also fix below warning while PowerPC T series boards compilation,
===================== WARNING ======================"
This board does use CONFIG_LIBATA but has CONFIG_AHCI not"
enabled. Please update the storage controller driver to use"
CONFIG_AHCI before the v2019.07 release."
Failure to update by the deadline may result in board removal."
See doc/driver-model/MIGRATION.txt for more info."
===================================================="
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
- remove "synopsys,dw-mipi-dsi" compatible to reduce the device tree
differences between Linux and U-Boot for stm32mp1 platform
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXdJyOg4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXOmuAJ9lF7GyPpv0vZNX1V4UV2EyyOOdbwCfQzHu3Xo+
3VWLV9ZHkVMlfnGbbx0=
=+YuG
-----END PGP SIGNATURE-----
Merge tag 'video-for-v2020.01-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- fix i.MX6ULL evk black screen observed while reboot stress tests
- remove "synopsys,dw-mipi-dsi" compatible to reduce the device tree
differences between Linux and U-Boot for stm32mp1 platform
- Add support for rockchip SoC: PX30, RK3308
- Add and migrate to use common dram driver: PX30, RK3328, RK3399
- Add rk3399 board Tinker-s support
- Board config update for Rock960, Rockpro64
A dm based dram driver for rk3308 u-boot
to get capacity.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add clk controller driver for RK3308 SOC.
This patch depends on Elaine's pll patch[0].
[0]http://patchwork.ozlabs.org/patch/1183718/
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Common PLL setup function, compatible with different SOC.
Mainly for the subsequent new SOC use.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_IS_ENABLED() needs the config name like used in Kconfig, so
without the leading CONFIG_. The clock drivers all wrongly check for
CONFIG_RESET_ROCKCHIP, fix that
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rockchip_reset_bind() already does the needed init for the reset
registers, only referenced the wrong cru structure.
So we can get rid of the open-coded reset init and just fix
the correct cru reference.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Newer Rockchip socs like the px30 use a different ip block to handle
one-time-programmable memory, so add a misc driver for it as well.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the glue code to allow the px30 variant of the Rockchip gmac
to provide network functionality.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The px30 contains 2 separate clock controllers, pmucru and cru.
Add drivers for them.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the necessary glue code to allow pinctrl setting on px30 socs.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There are some code different with rockchip vendor code which may lead
to different bugs, including:
1) Fix setting error about LPDDR3 dram size ODT.
2) Set phy io speed to 0x2.
3) Fix setting error about phy_pad_fdbk_drive.
4) Fix setting error about PI_WDQLVL_VREF_EN
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Update the calculation of the stride to support all the DRAM case.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The io setting are updated after some bugfix in different rk3399 boards,
sync the code from vendor.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Update lpddr timing in lpddr4-400 and lpddr4-800 file from rockchip
vendor code;
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add capacity detect for rk3399 so that the driver able to detect the
capacity automatically.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Clean up the sdram_init to keep sync with rockchip source code.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Clean up rk3399 dram driver source code for more readable.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
For there are some structures and functions are common for all rockchip SoCs,
migrate to use the common code so that we can clean up reduandent codes.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
RK3328 has a similar controller and phy with PX30, so we can use the
common driver for it and remove the duplicate codes.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add the sdram driver for PX30 to support ddr3, ddr4, lpddr2 and lpddr3.
For TPL_BUILD, the driver implement full dram init and without DM
support due to the limit of internal SRAM size.
For SPL and U-Boot proper, it's a simple driver with dm for get
dram_info like other SoCs.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
This sdram_phy_px30.c is based on PX30 SoC, the functions are common
for phy, other SoCs with similar hardware could re-use it.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
This sdram_pctl_px30.c is based on PX30 SoC, the functions are common
for controller, other SoCs with similar hardware could re-use it.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The debug info for dram is main about the capacity related info which is
very important the board init, so set this default enable.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The functions for dram info print are part of common code.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
There are some function like os_reg setting, capacity detect functions,
can be used as common code for different Rockchip SoCs, add a
sdram_common.c for all these functions.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
rename sdram_common.c in arch/arm/mach-rockchip to sdram.c;
so that we can use the file name sdram_common.c in dram driver for
better understand the code;
clean the related file who has use the header file at the same time.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The header file sdram.h is used for rk3288 and similar SoCs, rename it
to make it more understandable.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Remove the pinctrl_decode_pin_config() API, because this
function is unused and not compatible with livetree
(it uses fdtdec_get_bool instead of ofnode API).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove the compatible "synopsys,dw-mipi-dsi" added in U-Boot
(it don't exist in Linux kernel binding); it is only used
to bind the generic synopsys UCLASS_DSI_HOST "dw_mipi_dsi" to
the driver "stm32-display-dsi" UCLASS_VIDEO_BRIDGE
This binding is done in Linux kernel drivers without compatible
(dw_mipi_dsi_bind() is called in bind of driver, for example in
drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c).
This patch does the same in U-Boot driver, the STM32 driver
calls during its bind the function device_bind_driver_to_node
to bind the generic driver "dw_mipi_dsi" at the same address.
This patch reduces the device tree differences
between Linux kernel and U-Boot for stm32mp1 platform.
Tested with v2020.01-rc1 on STM32MP157C-EV1 and STM32MP157C-DK2.
The dependency of driver is clearer and the probe order is guaranteed.
STM32MP> dm tree
Class Index Probed Driver Name
-----------------------------------------------------------
root 0 [ + ] root_driver root_driver
sysreset 0 [ ] syscon_reboot |-- reboot
simple_bus 0 [ + ] generic_simple_bus |-- soc
serial 0 [ + ] serial_stm32 | |-- serial@40010000
...
video_brid 0 [ + ] stm32-display-dsi | |-- dsi@5a000000
dsi_host 0 [ + ] dw_mipi_dsi | | |-- dsihost
panel 0 [ + ] rm68200_panel | | `-- panel-dsi@0
...
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
-------------------
i.MX8MN SoC support
ROM API image download support
i.MX8MM enet enabling
-----BEGIN PGP SIGNATURE-----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=sgCz
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191105' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20191105
-------------------
i.MX8MN SoC support
ROM API image download support
i.MX8MM enet enabling
Running stress reboot test on a i.MX6ULL evk board with a
custom LCD can lead to splash screen failure (black screen).
After comparing the eLCDIF initialization with the Linux kernel
driver, it was noticed that the eLCDIF reset is the first operation
that needs to be done.
So do like the eLCDIF Linux driver and move the eLCDIF clock
frequency configuration after the eLCDIF reset and just prior to
setting the RUN bit.
With this change applied, no more black screen issues has been
found during overnight reboot stress tests.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
- Add support for rockchip pmic rk805,rk809, rk816, rk817
- Add rk3399 board Leez support
- Fix bug in rk3328 ram driver
- Adapt SPL to support ATF bl31 with entry at 0x40000
- Fix the u8 type comparision with '-1'.
- Fix checkpatch warning for multi blank line and review signature.
Fix a typo that caused incorrect values to be loaded into the DRAM
controller's deskew registers.
Signed-off-by: Simon South <simon@simonsouth.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Fix a pair of tests in phy_dll_bypass_set() that used incorrect units
for the DDR frequency, causing the DRAM controller to be misconfigured
in most cases.
Signed-off-by: Simon South <simon@simonsouth.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a call to rk3328_configure_cpu() during initialization to set the
CPU-clock frequency.
Signed-off-by: Simon South <simon@simonsouth.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK809 is a Power Management IC (PMIC) for multimedia
and handheld devices. They contains the following components:
- Regulators(5*BUCKs, 9*LDOs, 2*SWITCHes)
- RTC
- Clocking
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK817 is a Power Management IC (PMIC) for multimedia
and handheld devices. They contains the following components:
- Regulators(4*BUCKs, 1* BOOST, 9*LDOs, 1*SWITCH)
- RTC
- Clocking
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK805 are a Power Management IC (PMIC) for multimedia
and handheld devices. They contains the following components:
- Regulators(4*BUCKs, 3*LDOs)
- RTC
- Clocking
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK816 is a Power Management IC (PMIC) for multimedia
and handheld devices. They contains the following components:
- Regulators(4*BUCKs, 1*BOOST, 6*LDOs, 1*SWITCH)
- RTC
- Clocking
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to adapt the following pmics, make the interface more compatible.
Support buck and ldo suspend voltage setting and getting.
Supprot buck and ldo suspend enable/disable setting and getting.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the SPI_FLASH_BAR for the ESPI controller of FSL, this entry
is missed by
commit 6d82517836 ("configs: Don't use SPI_FLASH_BAR as default")
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The xHCI 1.1 version also need set Transfer Type field
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add the missing RGMII PHY modes in which case the MAC has configure its
RGMII settings. The only difference between these modes is the RX and
TX delay configuration. A user might choose any RGMII mode in the device
tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The saved ofnode is used by some PHY drivers to access the device tree
node of the PHY.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In ls_pcie_ep_enable_cfg(), as part of EP setup,config ready bit
of pci controller is set, so that RC can read the config space of EP.
While setting the config ready bit, LTSSM_EN bit in same register was
also inadvertently getting cleared. This restarts the link training
between RC and EP.
Update code to just set the desired CFG_READY bit (bit 0),
while leaving the other bits unchanged.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
j721e SoCs have different OPP tables. Add support for the same.
Note: DM Still has lot of voltages TBD hence the correct
values need to be programmed once they are published.
Signed-off-by: Keerthy <j-keerthy@ti.com>
TPS6236x is a family of step down DC-DC converters optimized for battery
powered portable applications for a small solution size. Add a regulator
driver for supporting these devices.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Adaptive Voltage Scaling is a technology used in TI SoCs to optimize
the operating voltage based on characterization data written to efuse
during production. Add a driver to support this feature for K3 line of
SoCs, initially for AM65x.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
This adds platform code and the device tree for the Phytium Durian Board.
The initial support comprises the UART and the PCIE.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Steven Hao <liuhao@phytium.com.cn>
To add usb-3.0 support to peripheral device add BOS & SS capability
descriptors to gadget composite framework.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Add a new bcdDevice entry for Cadence USB gadget controller similar to
other controller and add gadget_is_cdns3() macro as well.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add driver to handle TI specific wrapper for Cadence USB3 controller
present on J721e SoC. Based on Linux driver for the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Implement udc_set_speed() callback to limit Controller's speed to
high-speed/full-speed when working with gadgets that are high-speed or
full-speed only
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add support for USB3 host and gadget driver. This is a direct sync of
Linux kernel Cadence USB stack that from v5.4-rc1 release.
Driver has been modified so that it compiles without errors against
U-Boot code base.
Features not required for U-Boot such as scatter-gather DMA and OTG
interrupt handling has been dropped.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
[jjhiblot@ti.com: Add PHY support]
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This patch was copied from kernel commit: 67fdfda4a99ed.
Sometimes, the gadget driver we want to run has max_speed lower than
what the UDC supports. In such situations, UDC might want to make sure
we don't try to connect on speeds not supported by the gadget
driver because that will just fail.
So here introduce a new optional ->udc_set_speed() method which can be
implemented by interested UDC drivers to achieve this purpose.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add match_ep() op to usb_gadget_ops similar to Linux kernel which is
useful in finding a suitable ep match for the function driver. This will
avoid adding more gadget_is_xxx() handling code to usb_ep_autoconfig().
Also sync usb_ep_caps struct thats is usually used in the match_ep()
callback by the gadget controller driver
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
add DM based PCI Configuration space access support for
MPC85xx PCI Bridge. This driver is based on
arch/powerpc/cpu/mpc85xx/pci.c
In the old driver there is a fix for a hw issue on the
TARGET_MPC8555CDS and TARGET_MPC8541CDS boards. As I
have no such hardware I did not port this part.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add more clks for fec_mxc according to Linux Kernel 5.4.0-rc1
drivers/net/ethernet/freescale/fec_main.c.
Since i.MX8MQ not support CLK_CCF, so add a check to restrict
the code only effect when CONFIG_IMX8M and CONFIG_CLK_CCF both defined.
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Make FEC driver could be used by i.MX8M when CONFIG_FEC_MXC defined
in defconfig.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Add set_parent callback, then assigned-clock-parents in dts could
be work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Add enet ref/timer/PHY_REF/root clk which are required to make enet
function well.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Add i.MX8MM ccf driver support.
Modifed from Linux Kernel 5.3.0-rc1, drop some entries
that not used in U-Boot and adapt to U-Boot CCF style.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Lukasz Majewski <lukma@denx.de>
The power domain tree is not accepted by Linux Kernel upstream.
only a single pd node is used currently, as following:
pd: imx8qx-pd {
compatible = "fsl,imx8qm-scu-pd", "fsl,scu-pd";
#power-domain-cells = <1>;
};
So to migrate to use upstream linux dts, we also need a driver
to support this.
This patch is to support the new method, compared with legacy power
domain tree, it will be simpiler, because each device will
has resource id as power domain index, it will be directly passed
to scfw, and no need to let power domain build that tree. If multiple
power domain is needed, it is the dts node should has correctly power
domains entry added and sequence correct.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The current i.MX8 power domain driver is based on i.MX vendor
power domain tree which will retire later.
The Linux upstream use a single pd node for power domain driver,
and U-Boot will adopt that. When U-Boot i.MX8 dts synced with
Linux Kernel upstream and related driver ready, the legacy
driver will be removed.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
clk and pinctrl will be get(probed) during each device probe,
we don't need to probe them in scu driver. Only need to bind the sub-nodes
(clk and iomuxc) of MU node with their drivers.
So drop the code to probe the clk/pinctrl, and this patch will make it
easy to add more subnodes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To enable HS400(ES) and UHS for imx8m platforms, update the driver data
to share with imx8qm esdhc_soc_data.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
During mmc initialization, there are several calls to mmc_set_clock
and mmc_set_ios. When mmc_power_off, the mmc->clock will be set,
but the imx driver will use 400KHz. So the following calls
to mmc_set_ios will set the clock several times which is redundant
in fsl_esdhc_imx driver. So let's simplify to remove redundant
clock settings.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The QorIQ eSDHC on all platforms supports checking write protect
state through register bit. So check it always.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The fsl_esdhc_init() was actually to get configuration of mmc_config.
So rename it to fsl_esdhc_get_cfg_common() and make it common for both
DM_MMC and non-DM_MMC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to clean up bus width setting code.
- For DM_MMC, remove getting "bus-width" from device tree.
This has been done in mmc_of_parse().
- For non-DM_MMC, move bus width configuration from fsl_esdhc_init()
to fsl_esdhc_initialize() which is non-DM_MMC specific.
And fix up bus width configuration to support only 1-bit, 4-bit,
or 8-bit. Keep using 8-bit if it's not set because many platforms
use driver without providing max bus width.
- Remove bus_width member from fsl_esdhc_priv structure.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Voltage validation should be done by CMD8. Current comparison between
mmc_cfg voltages and host voltage capabilities is meaningless.
So drop current comparison and let voltage validation is through CMD8.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Controller initialization is not needed in fsl_esdhc_init().
It will be done in esdhc_init() for non-DM_MMC, and in
esdhc_init_common() in probe for DM_MMC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Conver TI CPSW driver to use dev/ofnode api.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
[trini: Add <dm/ofnode.h> to provide the prototype to ofnode]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Add support for Intel FSP-S and FSP-T in binman
- Correct priority selection for image loaders for SPL
- Add a size check for TPL
- Various small SPL/TPL bug fixes and changes
- SPI: Add support for memory-mapped flash
On i.MX7 in a sake of reducing the disturbances caused by a neighboring
cells in the FCB page in the NAND chip, a randomizer is enabled when
reading the FCB page by ROM bootloader.
Add API for setting BCH to specific layout (and restoring it back) used by
ROM bootloader to be able to burn it in a proper way to NAND using
nandbcb command.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Need to pass total 5 arguments for SIP HAB call on i.MX8MQ,
so update the interface to add new argument.
Signed-off-by: Ye Li <ye.li@nxp.com>
[agust: fixed imx8m-power-domain build]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Set gd->fb_base so it can be shown with bdinfo command.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The expire_now function was previously setting the watchdog timeout to
minimum and waiting for the watchdog to expire. However, this watchdog
also has bits to trigger immediate reset. Use those instead, like the
Linux imx2_wdt driver does.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
The Linux imx2_wdt driver uses a fsl,ext-reset-output boolean in the
device tree to specify whether the board design should use the external
reset instead of the internal reset. Use this boolean to determine which
mode to use rather than using external reset unconditionally.
For the legacy non-DM mode, the external reset is always used in order
to maintain the previous behavior.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Now AM65x CPSW2G driver will disable MAC TX internal delay for PHY
interface mode "rgmii-rxid" which is incorrect. Hence, fix it by keeping
default value (enabled) for MAC TX internal delay when "rgmii-rxid"
interface mode is selected.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Now TI CPSW driver will disable MAC TX internal delay for PHY interface
mode "rgmii-rxid" which is incorrect.
Hence, fix it by keeping default value (enabled) for MAC TX internal delay
when "rgmii-rxid" interface mode is selected.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
This patch adds support for standard Ethernet "max-speed" DT property to
allow PHY link speed limitation.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
According to TRMs the 10Mbps link speed is supported in RGMII only when
CPSW2G MAC SL is configured for External Control ("in band") mode
CPSW_SL_MACCTRL.EXT_EN(18) = 1.
Hence update cpsw_slave_update_link() to follow documentation.
[1] https://patchwork.kernel.org/patch/10285239/
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
At present the value of the timer base is used to determine whether the
timer has been set up or not. It is true that the timer is essentially
never exactly 0 when it is read. However 'time 0' may indicate the time
that the machine was reset so it is useful to be able to denote that.
Update the code to use a separate flag instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function can be called before the timer is set up. Make sure that the
init function is called so that it works correctly.
This is needed so that bootstage can work correctly in TPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
On x86 platforms the SPI flash can be mapped into memory so that the
contents can be read with normal memory accesses.
Add a new SPI method to find the location of the SPI flash in memory. This
differs from the existing device-tree "memory-map" mechanism in that the
location can be discovered at run-time.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
ARC fixes for v2020.01-rc2
The main change is move to DM_MMC of yet 2 another ARC boards:
AXS101 & IoTDK.
Among that we improve handling of stock-formatted SD-cards of high volume
on EM SDP as well as introduction of reset driver for HSDK which is required
for prepser reinitialization of some peripherals like USB etc.
