Rename fsl-ls1028a-qds.dts to fsl-ls1028a-qds.dtsi so that
it can be used as common device tree for lpuart and duart.
Add lpuart device tree and duart device tree respectively
for qds which are used with duart and lpuart console.
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In order to maintain compatibility with the Linux DTS, the entire fsl-mc
node is added but instead of being probed by a dedicated bus driver it
will be a simple-mfd.
Also, annotate the external MDIO nodes and describe the PHYs (8 x
VSC8514, AQR105). Also, add phy-handles for the dpmacs to their
associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In order to maintain compatibility with the Linux DTS, the entire fsl-mc
node is added but instead of being probed by a dedicated bus driver it
will be a simple-mfd.
Also, annotate the external MDIO nodes and describe the PHYs (4 x AQR405
and 4 x CS4340). Also, add phy-handles for the dpmacs to their
associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In order to maintain compatibility with the Linux DTS, the entire fsl-mc
node is added but instead of being probed by a dedicated bus driver it
will be a simple-mfd.
Also, annotate the EMDIO1 node and describe the 2 AR8035 RGMII PHYs and
the 2 AQR107 PHYs. Also, add phy-handles for the dpmacs to their
associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the External MDIO1 device node found in the WRIOP global memory
region. This is needed for management of external PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the External MDIO1 device node found in the WRIOP global memory
region. This is needed for management of external PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the External MDIO device nodes found in the WRIOP global memory
region. This is needed for management of external PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The Cubieboard is a single board computer containing a
Actions S700 SoC(with 4 ARMv8 Cortex-A53 cores).
This patch adds respective defconfig alongwith .dts(copied
from Linux v5.5-rc6 with hash "b3a987b0264d").
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Devices like uart and clk are needed to be enabled before relocation.
this patch adds u-boot.dtsi file that mark these device as dm-pre-reloc.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This patch adds .dtsi file(sync with Linux 5.5-rc6 with hash "b3a987b0264d")
and required binding for S700 SoC that is a 64-bit Quad-core ARM
Cortex-A53 cores.
It also provisions dts file to be built based on selected
platform(CONFIG_MACH_S900/S700).
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Devices like uart and clk are needed to be enabled before relocation.
This patch adds u-boot.dtsi file that mark these device as dm-pre-reloc.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Synchronize device tree bindings with v5.5-rc6 tag with commit id
"b3a987b0264d".
Also, it removes older clock binding defined for S900 along with undocumented
compatible string "actions,s900-serial" from serial driver and adapts clock
driver to cater to new bindings.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
The AV96 is in fact an assembly of DH Electronics DHCOR SoM on top
of an AV96 reference board. Split the DTs to reflect that and make
sure to DHCOR SoM can be reused on other boards easily.
It is also highly recommended to configure the board for the DHCOM
make stm32mp15_dhcom_basic_defconfig
make DEVICE_TREE=stm32mp15xx-dhcor-avenger96
as that permits reusing the board code for the DH components, like
accessing and reading out the ethernet MAC from EEPROM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: I7db47280d4eb0d668eb4e006355240271154f97f
The PLL4 is supplying SDMMC12, SDMMC3 and SPDIF with 120 MHz and
FDCAN with 96 MHz. This isn't good for the SDMMC interfaces, which
can not easily divide the clock down to e.g. 50 MHz for high speed
SD and eMMC devices, so those devices end up running at 30 MHz as
that is 120 MHz / 4. Adjust the PLL4 settings such that both PLL4P
and PLL4R run at 100 MHz instead, which is easy to divide to 50MHz
for optimal operation of both SD and eMMC, SPDIF clock are not that
much slower and FDCAN is also unaffected.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Remove the unnecessary file stm32mp157-pinctrl.dtsi and
solve all issues introduced by the commit 8914831860 ("Merge branch
'next'") after a conflict on the patch applied in the next branch in
commit 1a4f57c895 ("ARM: dts: stm32mp1: DT alignment with Linux 5.6-rc1")
Need to reapplied on stm32mp15-pinctrl.dtsi the the 3 patches
applied previously on file "stm32mp157-pinctrl.dtsi" in v2020.04
- commit 4fdbe6487d ("ARM: dts: stm32: Add alternate pinmux for SDMMC1
direction pins")'
- commit 5fdcba6402 ("ARM: dts: stm32: Add alternate pinmux for SDMMC2
pins 4-7")'
- commit 955de51111 ("ARM: dts: stm32: Add alternate pinmux for ethernet
RGMII")'
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
- Further cleanups for 'make refcheckdocs'
- Another BTRFS fix.
- Support for automatic decompression of images with booti as well as
unlz4 command for manual decompression.
- fix SMBIOS info on Odroid-C2
- Fix video output on GXBB/GXL/GXM boards
- add USB gadget support for GXL/GXM boards
-----BEGIN PGP SIGNATURE-----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=1Ffl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200420' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- enable DM_RNG on meson boards
- fix SMBIOS info on Odroid-C2
- Fix video output on GXBB/GXL/GXM boards
- add USB gadget support for GXL/GXM boards
- Fix boot on am335x guardian board
- Increase OPSI speed on AM65x and J721E devices
- Use JTAD register for identifying K3 devices.
- Update TI entry in MAINTAINERS file.
Add the USB DWC2 node to u-boot specific dtsi files since Gadget
support is not (yet) available in upstream Linux yet.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Those two boards are supposed to be run with a single u-boot binary.
There are notable differences though - HSC uses DSA switch (which
phy_id == 0x0) and DCC (DP83848C).
After the commit 3bf135b6c3
("drivers: net: phy: Ignore PHY ID 0 during PHY probing") the PHY devices
with phy_id == 0 are not created in U-Boot anymore. This caused regression
on HSC.
To fix this problem - the fec's 'fixed-link' node has been introduced and
the phy_id is not assessed anymore. This approach works on both boards.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
During the conversion of this board to DM_REGULATOR, usb-mass-storage
was broken and started failing with the following error:
=> ums 0 mmc 2
UMS: LUN 0, dev 2, hwpart 0, sector 0x0, count 0xe90000
Error enabling VBUS supply
g_dnl_register: failed!, error: -38
g_dnl_register failed
Fix this by adding the relevant GPIO to the regulator node.
Fixes: 4ca99fe81a ("ARM: imx: dh-imx6: Enable DM regulator")
Signed-off-by: Harald Seiler <hws@denx.de>
Use DM_ETH instead of legacy networking. Add VIO as a fixed regulator
to the relevant device-trees and augment the FEC node with properties
for the reset GPIO.
It should be noted that the relevant properties for the reset GPIO
already exist in the PHY node (reset-gpios, reset-delay-us,
reset-post-delay-us) but U-Boot currently ignores those and only
supports the bus-level reset properties in the FEC node
(phy-reset-gpios, phy-reset-duration, phy-reset-post-delay).
Signed-off-by: Harald Seiler <hws@denx.de>
The detection of the revD1 version is based on the presence of the PMIC.
Currently revb1 device trees are used for mx6q/mx6dl variants, which
do not have the PMIC nodes.
This causes revD1 boards to be incorrectly be detected as revB1.
Fix this issue by using the revd1 device trees, so that the PMIC node can be
found and then the PMIC can be detected by reading its register ID.
Imported the revd1 device trees from mainline kernel version 5.7-rc1.
Reported-by: Heiko Schocher <hs@denx.de>
Reported-by: Derek Atkins <derek@ihtfp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Derek Atkins <derek@ihtfp.com>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Linux doesn't provide skeleton.dtsi file so let's remove its include and
provide #address-cells/size-cells = <1> that were defined in
skeleton.dtsi before.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
The device trees for TQMa6x SOM support variations in
- CPU type: imx6dl- or imx6q-
- MBa6 I2C bus access: -mba6a (i2c1) or -mba6b (i2c3)
(plus the respective common/module include trees)
- USBH1 is directly connected to a hub
- USBOTG is connected to a separate connector
and can act as host/device or full OTG port.
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@ew.tq-group.com>
The Linux VPU bindings have changed and dropped the dmc register range.
Add it back in the meson-gx-u-boot.dtsi file until a proper canvas driver
is available.
Fixes: dd5f2351e9 ("arm64: dts: meson: sync dt and bindings from v5.6-rc2")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The libretech-ac u-boot.dtsi file is missing to enabled DT nodes changes
to enable Video output on U-Boot.
Fixes: 671b1db8f8 ("arm64: dts: meson-gx: vpu should be probed before relocation")
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
The LED labels do not match the silkscreen on the board, fix it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add DT entries, Kconfig entries and board-specific entries to configure
FMC2 bus and make KS8851-16MLL on that bus accessible to U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
- Misc enhancements to Clearfog, including board variant detection
(Joel)
- Misc enhancements to Turris Mox, including generalization of the
ARMADA37xx DDR size detection (Marek)
Commit e8e9715df2 requires the USB3 regulator node to have the
enable-active-high property for the regulator to work properly. The
GPIO_ACTIVE_HIGH constant is not enough anymore.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Fixes: e8e9715df2 ("regulator: fixed: Modify enable-active-high...")
Reviewed-by: Stefan Roese <sr@denx.de>
With recent changes to the mmc subsystem (chip detect code etc) update
the sdhci node of the Turris Mox device tree.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Using a consistent hardcoded MAC address from the DTS file causes
issues when using multiple devices on the same network segment.
Instead rely on environment configuration or random generation.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Sort the Armada series dts in the Makefile alphabetically
prior to adding new board support.
Signed-off-by: Josip Kelečić <josip.kelecic@sartura.hr>
Reviewed-by: Luka Kovacic <luka.kovacic@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
In 1 bit mode OSPI can work at upto 50MHz, this provides better write
performance. Therefore increase frequency from 40MHz to 50MHz
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
In 1 bit mode OSPI can work at upto 50MHz, this provides better write
performance. Therefore increase frequency from 40MHz to 50MHz
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
- As there is a requirement to store certain data, we need a persistent
storage in u-boot. Hence, we need to save env in NAND
- Add default Guardian environment variables
- Update partition table:
- Reserve some space for experimentation, this ensures proper
backwards compatibility
- Update defconfig accordingly
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
This patch enables the guardian board to provide feedback
about the boot stage in headless mode. The on-board led
would behave in the following pattern
* U-boot -> GLOW LED
* Linux -> BLINK LED [HEART-BEAT PATTERN]
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
Pull in changes that have been pending in our 'next' branch. This
includes:
- A large number of CI improvements including moving to gcc-9.2 for all
platforms.
- amlogic, xilinx, stm32, TI SoC updates
- USB and i2c subsystem updtaes
- Re-sync Kbuild/etc logic with v4.19 of the Linux kernel.
- RSA key handling improvements
Adding "u-boot,dm-pre-reloc" and enable CONFIG_SPL_CACHE
to enable cache driver in SPL.
This fixed error below in SPL:
cache controller driver NOT found!
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Update these 3 files from Linux:.
- socfpga_arria10.dtsi (Commit ID c1459a9d7e92)
- socfpga_arria10_socdk.dtsi (Commit ID d9b9f805ee2b)
- socfpga_arria10_socdk_sdmmc.dts (Commit ID 17808d445b6f)
Change in socfpga_arria10.dtsi:
- Add clkmgr label, so that can reference to it in u-boot.dtsi.
Change in socfpga_arria10-u-boot.dtsi:
- Add compatible and altr,sysmgr-syscon for uboot.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Move Uboot specific properties to *u-boot.dtsi files.
Preparation to sync Arria 10 device tree from Linux.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add and enable RTC-backed boot counter on ABB SECU1 platform.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
