Using an array is pointless; even more pointless (and scary) is using
sprintf to fill it without a format string.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Remove the in-structure ops and put them in mmc_ops with
a constant pointer to it.
This makes the mmc structure smaller as well as conserving
code space (in theory).
All in-tree drivers are converted as well; this is done in a
single patch in order to not break git bisect.
Changes since V1:
Fix compilation b0rked issue on omap platforms where OMAP_GPIO was
not set.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
This patch enables support for device tree for sdhci driver.
Non DT case is still supported.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add support for the Kona SDHCI found on Broadcom mobile SoCs.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>
With d6a320d we moved some clock externs out of blackfin_local.h and
into clock.h but now need to include <asm/clock.h> in more drivers to
avoid warnings.
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Tom Rini <trini@ti.com>
The open and close mmc sub-commands implement a hard-coded set of values
specific to the SMDK5250 platform. Remove these commands as what they
did can be done instead with a series of mmc dev / bootpart / bootbus
commands instead now.
Cc: Amar <amarendra.xt@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Add a bootbus sub-command to the mmc command to allow for setting
the boot_bus_width, reset_boot_bus_width and boot_mode fields of
BOOT_BUS_WIDTH (EXT_CSD[177]).
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Add a partconf sub-command to the mmc command to allow for setting
the boot_ack, boot_partition and partition_access fields of
PARTITION_CONFIG (formerly BOOT_CONFIG, EXT_CSD[179]). Part of this
requires changing the check for 'part' from an strncmp to a strcmp, like
the rest of the sub-commands.
Cc: Andy Fleming <afleming@gmail.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
As per the below commit
"mmc: sdhci: add the quirk for broken r1b response"
(sha1: 3a6383207b)
need to add quirk SDHCI_QUIRK_BROKEN_R1B, when the
response type is R1b.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
This patch corrects the divider value written to CLKDIV register.
Since SDCLKIN is divided inside controller by the DIVRATIO value set
in the CLKSEL register, we need to use the same output clock value to
calculate the CLKDIV value.
as per user manual: cclk_in = SDCLKIN / (DIVRATIO + 1)
Input parameter to mmc_clk is changed to dwmci_host, since
we need the same to read DWMCI_CLKSEL register.
This improves the read timing values for channel 0 on SMDK5250
from 0.288sec to 0.144sec
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
U-Boot currently sets MMC cards' RCA register to 0. This value is
reserved according to the specification. Use a value of 1 instead, just
like the Linux kernel.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Tegra124's MMC controller is very similar to earlier SoC generations,
and can be supported by the same driver.
However, there are some non-backwards-compatible HW differences, and
hence a new DT compatible value must be used to describe the HW. This
patch updates the driver to support that new compatible value.
That said, the HW differences are only relevant when enabling certain
high-performance transfer modes. Since the driver is currently very
simple and doesn't enable those modes, we don't actually need to address
any of these HW differences in the code yet, hence the simple nature of
this patch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The upper 4 data signals of esdhc are shared with spi flash.
So detect if the upper 4 pins are assigned to esdhc before
enable sdhc 8 bit width.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Card detection pin is ineffective on T4240QDS Rev1.0.
There are two cards can be connected to board.
1. eMMC card is built-in board, can not be removed. so
For eMMC card it is always there.
2. Card detecting pin is functional for SDHC card in Rev2.0.
This workaround force sdhc driver scan and initialize the card
regardless of whether the card is inserted or not in case Rev1.0.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
To add the DesignWare MMC driver support for Altera SOCFPGA. It
required information such as clocks and bus width from platform
specific files (SOCFPGA handoff files)
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The eMMC and the SD-Card specifications describe the optional SET_DSR command.
During measurements at our lab we found that some cards implementing this feature
having really strong driver strengts per default. This can lead to voltage peaks
above the specification of the host on signal edges for data sent from a card to
the host.
Since availability of a given card type may be shorter than the time a certain
hardware will be produced it is useful to have support for this command (Alternative
would be changing termination resistors and adapting the driver strength of the
host to the used card.)
Following proposal for an implementation:
- new field that reflects CSD field DSR_IMP in struct mmc
- new field for design specific DSR value in struct mmc
- board code can set DSR value in mmc struct just after registering an controller
- mmc_startup sends the the stored DSR value before selecting a card, if DSR_IMP is set
Additionally the mmc command is extended to make is possible to play around with different
DSR values.
The concept was tested on a i.MX53 based platform using a Micron eMMC card where the default
DSR is 0x0400 (12mA) but in our design 0x0100 (0x0100) were enough. To use this feature for
instance on a mx53loco one have to add a call to mmc_set_dsr() in board_mmc_init() after
calling fsl_esdhc_initialize() for the eMMC.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Fixup prints to show where the print is done from, and
a few minor formatting/grammar issues.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Bounce buffer implementation takes care of proper data buffer alignemt
and correct flush/invalidation of data cache at once so we no longer
depend on input data variety and make sure CPU and MMC controller deal
with expected data in case of enabled data cache.
Bounce buffer requires to add its definition (CONFIG_BOUNCE_BUFFER) in
board configuration, otherwise corresponding library won't be compiled
and linker will fail to build resulting executable.
Difference since v1 - fixed compile-time warning with type casting to
"void *":
Slight edit to remove UTF8 characters in the commit message.
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
====
passing argument 2 of 'bounce_buffer_start' discards 'const' qualifier
from pointer target type
====
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Amar <amarendra.xt@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Andy Fleming <afleming@gmail.com>
To enhance the SDMMC DesignWare driver to use calloc instead of
malloc. This will avoid the incident that uninitialized members
of mmc structure are later used for NULL comparison.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Faraday FTSDC021 is a controller which is compliant with
SDHCI v3.0, SDIO v2.0 and MMC v4.3.
However this driver is only verified with SD memory cards.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
CC: Andy Fleming <afleming@gmail.com>
Existing eSDHC SPL framework assumes booting from sd-image
with boot_format header which contains final u-boot Image
offset and size. No such header is present in case of
corenet devices like T1040 as corenet deivces use PBI-RCW
based intialization.
So, for corenet deives, SPL bootloader use values provided
at compilation time. These values can be defined in board
specific config file.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
If platform provides "host->fifoth_val" it will be used for
initialization of DWMCI_FIFOTH register. Otherwise default value will be
used.
This implementation allows:
* escape unclear and recursive calculations that are currently in use
* use whatever custom value for DWMCI_FIFOTH initialization if any
particular SoC requires it
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Amar <amarendra.xt@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Andy Fleming <afleming@freescale.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
dw-mmc.c is the general driver file.
So, remove the exynos specific code at dw-mmc.c.
Instead, exynos specific cod can be move into exynos-dw_mmc.c.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
T4240QDS eSDHC host capabilities reigster should have VS33 bit define.
Add quirk CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 to deal with capacity
missing
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
struct mmc should be clear to all '0' after malloc to avoid
unexpect variable value.
Like mmc->has_init = xxx.
In this case mmcinfo will believe the card had been initialized before
and skip the initialization.
Test on P5040 and T4240,
Error Log:
=> mmcinfo
Device: FSL_SDHC
Manufacturer ID: 0
OEM: 0
Name: Tran Speed: 0
Rd Block Len: 0
MMC version 0.0
High Capacity: No
Capacity: 0 Bytes
Bus Width: 0-bit
=>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Signed-off-by: Xie Shaohui-B21989 <B21989@freescale.com>
Tested-by: Ryan Barnett <rjbarnet@rockwellcollins.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
eSDHC host controller has new register to support SD Spec 3.0.
And the according host controller version was Freescale eSDHC
Version 3.0.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
SMDK5420 has a new Security Management Unit added
for dwmmc driver, hence, configuring the control
registers to support booting via eMMC.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Old command timeout value was too small and it caused I/O errors which
led to uncompleted read/write/erase operations and filesystem errors.
Timeout adaptation fixes this issue.
Changes in sdhci_send_command() function:
- change timeout variable to static
- increase default command timeout to 100 ms
- add definition of max command timeout value,
which can be redefined in each board config file
- wait for card ready state for max defined time
if it doesn't exceed defined maximum or return COMM_ERR
Once successfully increased timeout value will be used in next function
call. This fix was tested on Goni, Trats, Trats2 boards by testing UMS
on MMC storage.
Changes v2:
- move global variable cmd_timeout into function sdhci_send_command()
- change condition "==" to ">=" when comparing time with timeout
- print information about timeout increasing and card busy timeout
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
To prevent the confusion, use the get_mmc_clk() instead of mmc_clk().
get_mmc_clk() is more exactly name.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
EXT_CSD_ERASE_GROUP_DEF is lost every time after a reset or
power off. Set it if device has enhanced partitions.
Signed-off-by: Oliver Metz <oliver@freetz.org>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The patch fixes the improper read and write of sdhci
host control register for sdma transfer.
The problem comes when reading and writing 1 byte long
host control register with the sdhci_readl() and
sdhci_writel(). The misuse of these functions overwrite
the value of the next registers which are in 4 bytes boundary.
This patch replaces four byte register read/write functions
with one byte read/write ones. Beside, it eliminates
unnecessary bit operation. i.e. or-ing zero against a variable.
Signed-off-by: Juhyun (Justin) Oh <Juhyun_Oh@sigmadesigns.com>
This fixes two issues:
* a descriptor was allocated for every block, while a descriptor can
take 8 blocks
* there was an off-by-one error in the descriptor preparation: there
were two last descriptors, one with length==0
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Andy Fleming <afleming@gmail.com>
In dwmci_prepare_data, the descriptors are allocated for DMA transfer.
These are allocated using the ALLOC_CACHE_ALIGN_BUFFER. This macro uses
the stack to allocate these descriptors. This becomes a problem if the
DMA transfer continues after the processor leaves the function in which
the descriptors were allocated.
Therefore, I have moved the allocated of the buffers up one level, to
dwmci_send_cmd(). The DMA transfer should be complete when leaving this
function.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Andy Fleming <afleming@gmail.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
For SPL builds this is just dead code since we'll only need to read.
Eliminating it results in a significant size reduction for the SPL
binary, which may be critical for certain platforms where the binary
size is highly constrained.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
If we don't have CONFIG_SPL_LIBCOMMON_SUPPORT defined then stdio
& *printf functions are unavailable & calling them will cause a link
failure.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Enable 8-bit host capability for HSMMC2 and/or HSMMC3. CONFIG_HSMMC2_8BIT
(for OMAP4/5/DRA7xx) and/or CONFIG_HSMMC3_8BIT (for DRA7xx only) must be
defined in the board header if an 8-bit eMMC device is connected to the
corresponding port.
Fix the "No status update" error that appeared for eMMC devices by
inserting a 20 us delay between writing arguments and command. This
solution has been proposed by Michael Cashwell <mboards@prograde.net>.
A minor cosmetic fix in a comment as well.
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
"mmc_send_cmd: timeout: No status update" error sometimes happens in
omap_hsmmc driver func mmc_send_cmd() when the MMC controller card
identification and selection sequence is executed for eMMC on OMAP4
boards.
It happens due to incorrect execution of CMD line reset procedure
for OMAP4. Because CMD(DAT) lines reset procedures are slightly
different for OMAP3 and OMAP4(AM335x,OMAP5,DRA7xx).
According to OMAP3 TRM:
Set SRC(SRD) bit in MMCHS_SYSCTL register to 0x1 and wait until
it returns to 0x0.
According to OMAP4(AM335x,OMAP5,DRA7xx) TRMs, CMD(DATA) lines reset
procedure steps must be as follows:
1. Initiate CMD(DAT) line reset by writing 0x1 to SRC(SRD) bit in
MMCHS_SYSCTL register (SD_SYSCTL for AM335x).
2. Poll the SRC(SRD) bit until it is set to 0x1.
3. Wait until the SRC(SRD) bit returns to 0x0
(reset procedure is completed).
Unfortunately, at present omap_hsmmc driver has support only for
OMAP3. And as result step #2 is missing for OMAP4(AM335x,OMAP5,DRA7xx).
This sometimes leads to the fact that the waiting loop which is
required in step #3 does not executed, because SRC bit does not set
yet (at the moment of checking a condition of a loop execution).
And as a result this can cause to timeout error when sending a
next command.
In the particular case (working with eMMC witch do not respond to
some SD specific command) due to incorrect reset sequence after
command SD_CMD_SEND_IF_COND which finished with CTO flag within
64 clock cycles, the next command MMC_CMD_APP_CMD leads to a
timeout error within 1s.
So, extend CMD(DATA) lines reset procedure in func
mmc_reset_controller_fsm() by adding the missing step #2 for
OMAP4+/AM335x boards.
Signed-off-by: Oleksandr Tyshchenko <oleksandr.tyshchenko@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Do not call a memset for unused variable backup every time.
Remove unused variable from function.
Signed-off-by: Oleksandr Tyshchenko <oleksandr.tyshchenko@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Samsung SoC is supported the WIDE8, even if Controller version is v2.0.
So add the SDHCI_QUIRK_USE_WIDE8 for Samsung-SoC.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Enable support for high-capacity eMMC and MMC cards. The MXS MMC
driver has no problem with those.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Amaury Pouly <amaury.pouly@gmail.com>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
This patch cleans up license header in these files:
board/freescale/p1022ds/spl.c
drivers/mmc/fsl_esdhc_spl.c
drivers/mtd/spi/fsl_espi_spl.c
Signed-off-by: York Sun <yorksun@freescale.com>
The code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.
The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that
ddr spd code can get the interleaving mode setting in env. It loads
final uboot image from offset 96KB.
* final uboot image, size is variable depends on the functions enabled.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
The FTSDC010_DCR_FIFO_RST symbol is conditionally
defined in <faraday/ftsdc010.h> and it is available
available when CONFIG_FTSDC010_SDIO is enabled.
However the actual driver code unconditionally uses
the FTSDC010_DCR_FIFO_RST constant and this causes
build error if CONFIG_FTSDC010_SDIO is not enabled.
The following error happens when compiling for the
adp-ag101 board:
ftsdc010_mci.c: In function 'ftsdc010_request':
ftsdc010_mci.c:178: error: 'FTSDC010_DCR_FIFO_RST' undeclared (first use in this function)
ftsdc010_mci.c:178: error: (Each undeclared identifier is reported only once
ftsdc010_mci.c:178: error: for each function it appears in.)
The patch ensures that the FTSDC010_DCR_FIFO_RST
symbol gets used only if CONFIG_FTSDC010_SDIO is
defined.
Compile tested only.
Cc: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Reviewed-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Dealing with the sys ctrl register should touch only the
relevant bits and not accidently the whole register. On i.MX6,
the sys control register contains bits which shouldn't be reset to
0, e.g. SYS_CTRL[3-0] and IPP_RST_N (SYS_CTRL[23]).
Do this by read/modify/write instead of just a 32bit write.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
1. No contents of "asm/arch/clk.h" is used within "dw_mmc.c".
2. If arch doesn't have "asm/arch/clk.h" driver won't build.
Without mentioned inclusion dw_mmc driver could be built for arches
other than ARM. For ARM driver still builds without it.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Amar <amarendra.xt@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Fill the right command type when using CMD12 to stop data transfer.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
CC: Fleming Andrew-AFLEMING <AFLEMING@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
With CONFIG_SYS_64BIT_LBA, lbaint_t gets defined as a 64-bit type,
which is required to represent block numbers for storage devices that
exceed 2TiB (the block size usually is 512B), e.g. recent hard drives.
For some obscure reason, the current U-Boot code uses lbaint_t for the
number of blocks to read (a rather optimistic estimation of how RAM
sizes will evolve), but not for the starting address. Trying to access
blocks beyond the 2TiB boundary will simply wrap around and read a
block within the 0..2TiB range.
We now use lbaint_t for block start addresses, too. This required
changes to all block drivers as the signature of block_read(),
block_write() and block_erase() in block_dev_desc_t changed.
Signed-off-by: Sascha Silbe <t-uboot@infra-silbe.de>
Current DWMMC driver used to give FIFO underrun/overrun error every 3rd time
for mmc rescan command.
In current code FIFO_DEPTH is getting calculated after reading the default FIFOTH
register and extracting the RX_WMARK bits from it i.e (RX_WMARK = FIFO_DEPTH/2 -1).
Instead of storing the correct value, we were recalculating the FIFO_DEPT each
time which is not correct.
Based on "[PATCH V9 3/9] DWMMC: Initialise dwmci and resolve EMMC read write issues"
http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/160247
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Enhance the MMC core to calculate the size of each MMC partition, and
update mmc->capacity whenever a partition is selected. This causes:
mmc dev 0 1 ; mmcinfo
... to report the size of the currently selected partition, rather than
always reporting the size of the user partition.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
After waiting for the command completion event, the interrupt status
bits, that occured to be set by that time, are cleared by writing them
back. It is supposed, that it should be command related bits (command
complete and may be command errors).
However, in some cases the DMA already completes by that time before
the full transaction completes. The corresponding DINT bit gets set
and then cleared before even entering the loop, waiting for data part
completion. That waiting loop never gets this bit set, causing the
operation to hang. This is reported to happen, for example, for write
operation of 1 sector to upper area (block #7400000) of SanDisk Ultra II
8GB card.
The solution could be to explicitly clear only command related interrupt
status bits. However, since subsequent processing does not rely on
any command bits state, it could be easier just to remove clearing
of any bits at that point, leaving them all until all data processing
completes. After that the whole register will be cleared at once.
Also, on occasion, interrupts masking moved to before writing the command,
just for the case there should be no chance of interrupt between the first
command and interrupts masking.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Since commit 48e0b2bd (powerpc/esdhc: Correct judgement for DATA PIO mode)
we see mx6 systems to hang after doing a 'save' command.
Revert this commit since the original 'ifdef' logic from 7b43db92
(drivers/mmc/fsl_esdhc.c: fix compiler warnings) was the correct one.
Reported-by: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch fixes a bug related to mmc writes.
When doing fatwrites on an SD-Card, MMC bus problems can occur. Depending
on the size of the file, "MMC0: Bus busy timeout!" is reported, resulting
in an SD-Card that is no longer responding.
It appears to be, that set_cluster can be called with a size being zero.
That can be with a file that has a size being an exact multiple
(including 0) of the clustersize, but also for files that are smaller than
the size of one cluster.
The same problem occurs if the "mmc write" command is given with a block
count being 0.
By adding a check for the block count being zero in mmc_write_blocks
(drivers/mmc.c), this problem is solved.
Signed-off-by: Ruud Commandeur <rcommandeur@clb.nl>
Cc: Tom Rini <trini@ti.com>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Mats Karrman <Mats.Karrman@tritech.se>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
CAP register don't have any information for 8-bit buswidth support
on 2.0 sdhci spec, only from 3.0 onwards bit[18] got this information.
Due to this misassignment in sdhci, mmc is setting 8-bit buswidth using
mmc_set_bus_width even if controller doesn't support.
Below change has code information.
"mmc: Properly determine maximum supported bus width"
(sha1: 7798f6dbd5)
Bug log: <mmc plus and emmc cards)
-------
zynq-uboot> mmcinfo
Error detected in status(0x208100)!
Device: zynq_sdhci
Manufacturer ID: fe
.....
So enable 8-bit support only for 3.0 spec using CAP and for below 3.0
assign mmc->host_caps = MMC_MODE_8BIT on respective platform driver
if host have a support.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch adds APIs to access(open / close) and to resize boot partiton of EMMC.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds FDT support for DWMMC, by reading the DWMMC node data
from the device tree and initialising DWMMC channels as per data
obtained from the node.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enumerates dwmci and set auto stop command during
dwmci initialisation.
EMMC read/write is not happening in current implementation
due to improper fifo size computation. Hence modified the fifo size
computation to resolve EMMC read write issues.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The logic for the whether to configure for polling or DMA
was mistakenly reversed in this patch:
Commit 7b43db9211
drivers/mmc/fsl_esdhc.c: fix compiler warnings
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
CC: Sun Yusong-R58495 <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Faraday FTSDC010 is a MMC/SD host controller.
Although there is already a driver in current u-boot release,
which is modified from eSHDC and contributed by Andes Tech.
Its performance is too terrible on Faraday A36x SoC platforms,
so I turn to implement this new version of driver which is
10+ times faster than the old one.
It's carefully designed to be compatible with Andes chips,
so it should be safe to replace it.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Andy Fleming <afleming@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The mpc85xx repuires a special layout on the memory device that is
connected to the eSDHC controller interface. But the file spl_mmc.c
didn't handle this specfic case, there needs a special treatmen, in
the powerpc drictory. So, there is no longer to keep spl_mmc.c on
mpc85xx, CONFIG_SPL_FRAMEWORK is not set.
When CONFIG_SPL_MMC_SUPPORT is set and CONFIG_SPL_FRAMEWORK is not
set, there was an error in drivers/mmc/spl_mmc.c:
drivers/mmc/libmmc.o:(.got2+0x8): undefined reference to `spl_image'.
Now, the solution is to move the file "spl_mmc.c" to directory "common/spl".
Signed-off-by: Ying Zhang <b40530@freescale.com>
add mmc card support with atmel mci driver
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Using IP version for different setting
- Higher version supports 8bit mode
- Higher version bus width setting is different
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Since TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs,
rename twl6035_mmc1_poweron_ldo by a more generic palmas_mmc1_poweron_ldo
function.
Signed-off-by: Nishanth Menon <nm@ti.com>
TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs
Rename twl6035 to palmas to allow reuse across multiple current and
future platforms
As part of this change, change the CONFIG_TWL6035_POWER to
CONFIG_PALMAS_POWER and update usage of header file accordingly.
Signed-off-by: Nishanth Menon <nm@ti.com>
A malloc() followed by memset() can be simply replaced by calloc().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
If failed the add_host(), it is reasonable that return value of
add_sdhci().
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Without this additional delay, some eMMC don't negotiate properly bus width
Tested on:
- Toshiba THGBM2G8D8FBAIB
- Toshiba THGBM4G4D1HBAR
- Micron MTFC4GMVEA (the one giving the problem)
- Hynix H26M64002BNR
- SanDisk SDIN5E1-32G
Signed-off-by: Davide Bonfanti <davide.bonfanti@bticino.it>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Most of time that MMC driver spends on initializing a device is polling
OCR (operation conditions register). To decouple this polling loop,
device init is split into two parts: The first part fires the OCR query
command, and the second part polls the result. So the caller is now no
longer bound to the OCR-polling delay; he may fire the query, go
somewhere and then come back later for the result.
To use this, call mmc_set_preinit() on any device which needs this.
This can save significant amounts of time on boot (e.g. 200ms) by
hiding the MMC init time behind other init.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
log2 of the device block size serves as the shift value used to calculate
the block number to read in file systems when implementing avaiable block
sizes.
It is needed quite often in file systems thus it is pre-calculated and
stored in the block device descriptor.
Signed-off-by: Egbert Eich <eich@suse.com>
The number 512 appears quite a bit in the mmc code. Add a constant for this
so that it can be used here and in other parts of the code (e.g. SPL code
which loads from mmc).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@google.com>
block_read returns unsigned long, so it doesn't make sense to check for
< 0. and neither does marking the header structure as const and then
casting away the constness to load data into it.
Also cleanup some unneeded pointer casting while we're at it.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Reviewed-by: Tom Rini <trini@ti.com>
The following headers are moved to a i.MX common location:
- regs-common.h
- regs-apbh.h
- regs-bch.h
- regs-gpmi.h
- dma.h
This way this header can be re-used also by other i.MX platforms.
For example the i.MX6 which will need it for the upcoming NAND
support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Support to check whether the SD3.0 or not.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Rommel Custodio <sessyargc@gmail.com>
eMMC vesrion is supported up to v4.5.
But bootloader isn't saw the exact eMMC version.
After applied this patch,
if use the mmcinfo command, then can see the exactly mmc version.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Rommel Custodio <sessyargc@gmail.com>
Rework the waiting for transfer completion loop condition
to continue waiting until both Transfer Complete and DMA End
interrupts occur. Checking of DLA bit in Present State register
looks not needed in addition to interrupts status checking,
so it can be removed from the condition. Also, DMA Error
condition is added to the list of data errors, checked in the loop.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
The cache should invalidate the read buffer for
the SD card interface after the transfer complete,
not command-complete.
Tested-by: Andrew Gabbasov <Andrew_Gabbasov@mentor.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Apparently, CONFIG_SYS_HZ must be 1000. Change this, and fix the timer
driver to conform to this.
Have the timer implementation export a custom API get_timer_us() for use
by the BCM2835 MMC API, which needs us resolution for a HW workaround.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Maximum bus width supported by some i.MX6 boards is not 8bit like
others. In case where both host controller and card support 8bit transfers,
they agree to communicate on 8bit interface while some boards support only 4bit interface.
Due to this reason the mmc 8bit default mode fails on these boards. To rectify this,
define maximum bus width supported by these boards (4bit). If max_bus_width is not
defined, it is 0 by default and 8bit width support will be enabled in host
capabilities otherwise host capabilities are modified accordingly.
It is tested with a MMCplus card.
Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com>
cc: stefano Babic <sbabic@denx.de>
cc: Andy Fleming <afleming@gmail.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Gets rid of warnings from omap_gpio:
ERROR : check_gpio: invalid GPIO -1
(and undefined behaviour as the -1 error code is interpreted as gpio value)
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Let mmc_getcd() return true and mmc_getwp() false if mmc driver doesn't
provide handlers for them.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Add braces around first if test in each case to fix warning]
Signed-off-by: Tom Rini <trini@ti.com>
This adds a simple driver for the BCM2835's SD controller.
Workarounds are implemented for:
* Register writes can't be too close to each-other in time, or they will
be lost.
* Register accesses must all be 32-bit, so implement custom accessors.
This code was extracted from:
git://github.com/gonzoua/u-boot-pi.git master
which was created by Oleksandr Tymoshenko.
Portions of the code there were obviously based on the Linux kernel at:
git://github.com/raspberrypi/linux.git rpi-3.6.y
commit f5b930b "Main bcm2708 linux port" signed-off-by Dom Cobley.
swarren changed the following for upstream:
* Removed hack udelay()s in bcm2835_sdhci_raw_writel(); setting
SDHCI_QUIRK_WAIT_SEND_CMD appears to solve the issues.
* Remove register logging from read*/write* functions.
* Sort out confusion with min/max_freq values passed to add_sdhci().
* Use more descriptive variable names and calculations in IO accessors.
* Simplified and commented twoticks_delay calculation.
* checkpatch fixes.
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Oleksandr Tymoshenko <gonzo@bluezbox.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Andy Fleming <afleming@gmail.com>
Tegra30 requires the SD Bus Voltage & Power bits be set in the SD
Power Control register. Tegra20 works w/o them set, but do it anyway
for those SoCs as it's part of the SD spec. Also call a common
board pad init routine (pad_init_mmc) in mmc_reset(), used by
Tegra30 only for now.
Note that Tegra20 SD/MMC HW differs enough from Tegra20 that a
new compatible entry is used in the fdt compat_names/id tables.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
tegra_mmc_init() now parses the DT info for bus width, WP/CD GPIOs, etc.
Tested on Seaboard, fully functional.
Tamonten boards (medcom-wide, plutux, and tec) use a different/new
dtsi file w/common settings.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
This patch changes sdhci_init()'s behavior to NOT enable all interrupt
sources by default. Moreover interrupt signaling has been disabled.
This patch do not enable interrupts which aren't served in u-boot
(they are defined at sdhci.h but NOT used elsewhere):
- SDHCI_INT_CARD_INSERT, SDHCI_INT_CARD_REMOVE, SDHCI_BUS_POWER,
SDHCI_INT_CARD_REMOVE, SDHCI_INT_CARD_INT
Special care shall be put on SDHCI_INT_CARD_INT, which indicates
interrupt generated by SD card.
According to "SD Host Controller Simplified Spec. ver 3.00" when bit 8
(Card Interrupt Status Enable) at "Normal Interrupt Status Enable
Register" (offset 0x34) is set, the card interrupt detection is started.
Then eMMC card may cause the SD controller to set this bit and then this
interrupt is passed to booted OS and might cause kernel crash.
To sum up:
- Only enable interrupts, which are served at u-boot
- This cleanup as a side effect fixes SDHCI's CARD INTERRUPT problem at
Linux kernel (versions 3.6+, sdhci controller)
- Keep masked bits at "Normal Interrupt Signal Enable Register" (0x38h)
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Andy Fleming <afleming@freescale.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In master we had already taken a patch to fix the davinci GPIO code for
CONFIG_SOC_DM646X and in u-boot-ti we have additional patches to support
DA830 (which is CONFIG_SOC_DA8XX && !CONFIG_SOC_DA850). Resolve these
conflicts manually and comment the #else/#endif lines for clarity.
Conflicts:
arch/arm/include/asm/arch-davinci/gpio.h
drivers/gpio/da8xx_gpio.c
Signed-off-by: Tom Rini <trini@ti.com>
A seperate omap_sys_ctrl_regs structure is defined for
omap4 & 5. If there is any change in control module for
any of the ES versions, a new structure needs to be created.
In order to remove this dependency, making the register
structure generic for all the omap4+ boards.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Currently there's no appropriate place to store driver specific data
because the pointer that is meant for that (priv) is being used to
store the base address of mmc registers.
Introduce a new struct for storing driver specific data.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
There are 3 MMC/SD/SDIO controllers in OMAP SoCs, but only 2 structs
are defined for devices. This leads to data being written outside of
array bounds on systems that use all 3 controllers.
Update hsmmc_dev array to the correct size.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
This patch streamlines the differences between the MX23 and MX28 by
implementing a few helper functions to handle different DMA channel
mapping, different clock domain for SSP block and fixes a few minor
bugs.
First of all, the DMA channel mapping is now fixed in dma.h by defining
the actual channel map for both MX23 and MX28. Thus, MX23 now does no
longer use MX28 channel map which was wrong. Also, there is a fix for
MX28 DMA channel map, where the last four channels were incorrect.
Next, because correct DMA channel map is in place, the mxs_dma_init_channel()
call now bases the channel ID starting from SSP port #0. This removes the
need for DMA channel offset being added and cleans up the code. For the
same reason, the SSP0 offset can now be used in mxs_dma_desc_append(), thus
no need to adjust dma channel number in the driver either.
Lastly, the SSP clock ID is now retrieved by calling mxs_ssp_clock_by_bus()
which handles the fact that MX23 has shared SSP clock for both ports, while
MX28 has per-port SSP clock.
Finally, the mxs_ssp_bus_id_valid() pulls out two implementations of the
same functionality from MMC and SPI driver into common code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Add rsi/sdh support for bf60x.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>
The MX23 has different layout of DMA channels. Fix the MMC
driver to support MX23.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Some MXS based boards do not implement the card-detect signal. Allow
user to specify alternate card-detect implementation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
This does the same reset mask as done in v3.7 Linux kernel code.
The block is properly configured for MMC operation that way.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
The MX23 can only use two SSP ports.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Create function which converts SSP bus number to SSP register pointer.
This functionality is reimplemented multiple times in the code, thus
make one common implementation. Moreover, make it a switch(), since the
SSP ports are not mapped in such nice linear fashion on MX23, therefore
having it a switch will simplify things there.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
The clock data are not used by the driver, drop them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
All esdhc variants we know should support high capacity MMC cards,
so let's add MMC_MODE_HC host_caps unconditionally to support those
MMC cards (capacity > 2 GB).
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
At some point, a confusion arose about the use of the bit
definitions in host_caps for bus widths, and the value
in ext_csd. By coincidence, a simple shift could convert
between one and the other:
MMC_MODE_1BIT = 0, EXT_CSD_BUS_WIDTH_1 = 0
MMC_MODE_4BIT = 0x100, EXT_CSD_BUS_WIDTH_4 = 1
MMC_MODE_8BIT = 0x200, EXT_CSD_BUS_WIDTH_8 = 2
However, as host_caps is a bitmask of supported things,
there is not, in fact, a one-to-one correspondence. host_caps
is capable of containing MODE_4BIT | MODE_8BIT, so nonsensical
things were happening where we would try to set the bus width
to 12.
The new code clarifies the very different namespaces:
host_caps/card_caps = bitmask (MMC_MODE_*)
ext CSD fields are just an index (EXT_CSD_BUS_WIDTH_*)
mmc->bus_width integer number of bits (1, 4, 8)
We create arrays to map between the namespaces, like in Linux.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tegra's MMC driver does DMA, and hence needs cache-aligned buffers. In
some cases (e.g. user load commands) this cannot be guaranteed by callers
of the MMC APIs. To solve this, modify the Tegra MMC driver to use the
new bounce_buffer_*() APIs.
Note: Ideally, all U-Boot code will always provide address- and size-
aligned buffers, so a bounce buffer will only ever be needed for user-
supplied buffers (e.g. load commands). Ensuring this removes the need
for performance-sucking bounce buffer cache management and memcpy()s.
The one known exception at present is the SCR buffer in sd_change_freq(),
which is only 8 bytes long. Solving this requires enhancing struct
mmc_data to know the difference between buffer size and transferred data
size, or forcing all callers of mmc_send_cmd() to have allocated buffers
using ALLOC_CACHE_ALIGN_BUFFER(), which while true in this case, is not
enforced in any way at present, and so cannot be assumed by the core MMC
code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The current bouncebuf API requires all parameters to be passed to both
bounce_buffer_start() and bounce_buffer_stop(). Modify the bouncebuf
start function to accept a state structure as a parameter, and only
require that state struct to be passed to the stop function. This
simplifies usage of the bounce buffer by clients.
Don't modify the data pointer, but rather store the temporary buffer in
this state struct. The bouncebuf code ensures that client code can
always use a single buffer pointer in the state structure, irrespective
of whether a bounce buffer actually had to be allocated.
Move cache management logic into the bounce buffer code, so that each
client doesn't have to duplicate this. I believe there's no need to
invalidate the buffer before a DMA operation, since flushing the cache
should prevent any write-backs.
Update the MXS MMC driver for this change.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Bring in the code from Linux kernel.
Added to Linux kernel by:
commit e08c1694d9e2138204f2b79b73f0f159074ce2f5
Author: Andres Salomon <dilinger@queued.net>
Date: Fri Jul 4 10:00:03 2008 -0700
Some HW balks when writing both voltage setting and power up at the same
time to SDHCI_POWER_CONTROL register.
Signed-off-by: Rommel G Custodio <sessyargc@gmail.com>
CC: Andy Fleming <afleming@freescale.com>
v2: fix attribution and SOB
Signed-off-by: Andy Fleming <afleming@freescale.com>
The interpretation of the data returned by the MMC_CMD_ALL_SEND_CID
command was incorrect with respect to the JEDEC Standard No. 84-A441.
This change makes the interpretation correct with respect to the
defined fields of the CID register.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Taylor Hutt <thutt@chromium.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
If a board has all 8 data lines routed, the SD/MMC controller can still
operate in 4-bit (or presumably even 1-bit) mode. Adjust Tegra's MMC
driver to report the 4-bit capability even for 8-bit slots.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
fsl_esdhc.c:71:6: warning: symbol 'esdhc_xfertyp' was not declared. Should it be static?
fsl_esdhc.c:413:6: warning: symbol 'set_sysctl' was not declared. Should it be st
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
mmc.c:137:5: warning: symbol 'mmc_send_cmd' was not declared. Should it be static?
mmc.c:203:5: warning: symbol 'mmc_send_status' was not declared. Should it be static?
mmc.c:247:5: warning: symbol 'mmc_set_blocklen' was not declared. Should it be static?
mmc.c:440:5: warning: symbol 'mmc_read_blocks' was not declared. Should it be static?
mmc.c:510:5: warning: symbol 'mmc_go_idle' was not declared. Should it be static?
mmc.c:532:1: warning: symbol 'sd_send_op_cond' was not declared. Should it be static?
mmc.c:597:5: warning: symbol 'mmc_send_op_cond' was not declared. Should it be static?
mmc.c:661:5: warning: symbol 'mmc_send_ext_csd' was not declared. Should it be static?
mmc.c:683:5: warning: symbol 'mmc_switch' was not declared. Should it be static?
mmc.c:705:5: warning: symbol 'mmc_change_freq' was not declared. Should it be static?
mmc.c:775:5: warning: symbol 'sd_switch' was not declared. Should it be static?
mmc.c:796:5: warning: symbol 'sd_change_freq' was not declared. Should it be static?
mmc.c:935:6: warning: symbol 'mmc_set_ios' was not declared. Should it be static?
mmc.c:953:6: warning: symbol 'mmc_set_bus_width' was not declared. Should it be static?
mmc.c:1108:26: warning: dubious: !x & y
mmc.c:960:5: warning: symbol 'mmc_startup' was not declared. Should it be static?
mmc.c:1243:5: warning: symbol 'mmc_send_if_cond' was not declared. Should it be s
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This driver is no longer used and it's remaining users were converted
to the new generic PXA MMC driver. Thus, remove this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
MMC host controller requires a delay between every sdhci_send_cmd()
execution. In s5p_mmc driver (s5p_sdhci replaces this driver), a delay
of 1000us was provided after every mmc_send_cmd() call. Adding a quirk
in current sdhci driver to replicate the behaviour.
Without this delay, MMC initialization on Origen board fails with
following error messages.
Timeout for status update!
mmc fail to send stop cmd
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
In host-control register, DMA select bit field is present.
BUt in sdhci.c, didn't select for DMA.
if set CONFIG_MMC_SDMA, we need to set SDMA-select bit.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Timeout value is tunable.
When run read/write operation, sometime returned the timeout error.
Because the timeout value is too short.
So increased the enough timeout value.
(This timeout value is used to prevent the infinite loop.)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The recent removal of the cmd->flags field caused error in the
debuging code of mmc_spi. Fix this:
mmc_spi.c: In function 'mmc_spi_request':
mmc_spi.c:179:2: error: 'struct mmc_cmd' has no member named 'flags'
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Implement necessary code to use the generic bounce buffer routines
inside this driver. This replaces the MMC bounce buffer, which is
to be removed.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Since the at91sam9263, the mmc hardware support multi blocks read/write. So this driver enable it.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
On mxc, each SDHC instance has a dedicated clock, so gd->sdhc_clk is not
suitable for the multi-instance use case (initialization made directly with
fsl_esdhc_initialize()).
This patch fixes this issue by adding a configuration field for the SDHC input
clock frequency.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jason Liu <r64343@freescale.com>
Cc: Matt Sealey <matt@genesi-usa.com>
Cc: Andy Fleming <afleming@gmail.com>
The move is pretty straight-forward. ap20.h and tegra20.h were renamed to ap.h and tegra.h.
Some files remain in arch-tegra20 but 'include' a file in 'arch-tegra' with #defines & structs
that will be common between T20 and T30 HW. HW-specific #defines, etc. stay in the 'arch-tegra20'
'root' file.
All boards build OK w/MAKEALL -s tegra20. Checkpatch.pl runs clean. Seaboard works OK.
Signed-off-by: Tom Warren <twarren@nvidia.com>
- Convert the non-relocation part of board_init_f to spl_board_init, turn on CONFIG_SPL_BOARD_INIT in the configs.
- Remove duplicated code.
- Add spl_boot_device() that returns the statically chosen boot device.
Signed-off-by: Tom Rini <trini@ti.com>
Add a new flag, CONFIG_SPL_FRAMEWORK to opt into the common/spl SPL
framework, enable on all of the previously using boards. We move the
spl_ymodem.c portion to common/ and spl_mmc.c to drivers/mmc/. We leave
the NAND one in-place as we plan to replace it later in this series.
We use common/spl to avoid linker problems with respect to merging
constant strings in objects. Otherwise all strings in common/ will be
linked in and kept which grows SPL in size too much.
Signed-off-by: Tom Rini <trini@ti.com>
Convert TEGRA20_ defines to either TEGRA_ or NV_PA_ where appropriate.
Convert tegra20_ source file and function names to tegra_, also.
Upcoming Tegra30 port will use common code/defines/names where possible.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Some eMMC devices contain boot partitions, but do not set the PART_SUPPORT
bit in EXT_CSD_PARTITIONING_SUPPORT. Allow partition selection on such
devices, by enabling partition switching when EXT_CSD_BOOT_MULT is set.
Note that the Linux kernel enables access to boot partitions solely based
on the value of EXT_CSD_BOOT_MULT; EXT_CSD_PARTITIONING_SUPPORT only
influences access to "general" partitions.
eMMC devices affected by this issue exist on various NVIDIA Tegra
platforms (and presumably many others too), such as Harmony (plug-in eMMC),
Seaboard, Springbank, and Whistler (plug-in eMMC).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There were a couple of drivers that were actually using the flags
field of the cmd structure, despite the fact that no one ever
*set* that field. When we removed the field, those drivers failed
to compile. Replaced the references with the correct usage of
resp_type.
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch prevents dcache-related problem. The problem manifested
itself on the SPI driver, this is just a port to the MMC driver.
The scenario is the same. In case an "mmc read" is issued to a
buffer which was written right before it and data cache is enabled,
the cache eviction might happen during the DMA transfer into the
buffer, therefore corrupting the buffer. Clear any cache lines that
might contain the buffer to prevent such issue.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Samsung SoC use the cmu control to set clock.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Useless code is removed, and get buswidth value.
buswidth value will be used to choice the 4bit or 8bit.
(Now used 4bit mode in sdhci.c by default)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Samsung SoC is broken busy waiting for R1b type.
And clk delay control value is modified the previosuly value.
(that value used at the s5p_mmc.c)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Some boards have no Card Detect wired. In that case, set the CD test
bits in the standard interface.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When setting up the clocks in the sdhci driver, the "spec version"
must be masked off. Otherwise any time the vendor version is not 0,
the check will allways assume the interface is version 3. This breaks
when the interface is actually version 1 or 2.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Some eMMC devices contain boot partitions, but do not set the PART_SUPPORT
bit in EXT_CSD_PARTITIONING_SUPPORT. Allow partition selection on such
devices, by enabling partition switching when EXT_CSD_BOOT_MULT is set.
Note that the Linux kernel enables access to boot partitions solely based
on the value of EXT_CSD_BOOT_MULT; EXT_CSD_PARTITIONING_SUPPORT only
influences access to "general" partitions.
eMMC devices affected by this issue exist on various NVIDIA Tegra
platforms (and presumably many others too), such as Harmony (plug-in eMMC),
Seaboard, Springbank, and Whistler (plug-in eMMC).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Since the type of "ext_csd" was array of char, the following
calculation might fail when the value of ext_csd[EXT_CSD_SEC_CNT]
was minus.
capacity = ext_csd[EXT_CSD_SEC_CNT] << 0
| ext_csd[EXT_CSD_SEC_CNT + 1] << 8
| ext_csd[EXT_CSD_SEC_CNT + 2] << 16
| ext_csd[EXT_CSD_SEC_CNT + 3] << 24;
So, this patch changes the type of "ext_csd" to array of u8.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The controller can control high capacity cards. So, the patch adds
the flag. If the flag is not set, "mmcinfo" will fail when a high
capacity card is used.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
(!timeout) condition check in mmc_send_status() can never be met,
because do-while loop ends up with negative timeout value, -1.
Fix the check to handle TIMEOUT case correctly.
Signed-off-by: Jongman Heo <jongman.heo@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The cache snooping feature of Freescale's eSDHC IP is not available on i.MX, so
disable it globally for this architecture. This avoids setting no_snoop for all
i.MX boards, and it prevents setting a reserved bit of a reserved register if
fsl_esdhc_mmc_init() is used on i.MX, like in
arch/arm/cpu/armv7/imx-common/cpu.c/cpu_mmc_init().
Since no_snoop was only used on i.MX, get rid of it BTW.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
The sys_proto.h functions (except the boot modes) are compatible with
i.MX233 and i.MX28 so we use 'mxs' prefix for its methods.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This is make naming consistent with the kernel and devicetree and in
preparation of pulling out the common tegra20 code.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Configuration in vexpress and u8500.v1 is different from what
is needed in u8500.v2. As such, card configuration specifics need
to reside in the board file rather than the driver.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Tom Rini <trini@ti.com>
The DMA didn't work properly because the DMA descriptor wasn't
properly cleaned after it was used once. Also, the DMA_ENABLE bit
was enabled/disabled too late.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Large blocks (> 512b) shall be transfered via DMA to make
things a bit faster.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Move DMA and PIO data transfer parts into separate functions.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
The DMA mode didn't properly configure the DMA_ENABLE bit in CTRL1.
Also, it was using SSP0 DMA channel for all SSP devices.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
DA850/OMAP-L138 does not support strict MMC/SD boot mode. SPL will
be in SPI flash and U-Boot image will be in MMC/SD card. SPL will
do the low level initialization and then loads the u-boot image
from MMC/SD card.
Define CONFIG_SPL_MMC_LOAD macro in the DA850/OMAP-L138
configuration file to enable this feature.
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
For FSL low-end processors (VVN2.2), in order to detect the SD card,
we should enable PEREN, HCKEN and IPGEN to enable the clock.
Otherwise, after booting the u-boot, and then inserting the SD card,
the SD card can't be detected.
For SDHC VVN2.3 IP, these bits are reserved, and SDCLKEN is used.
And when accessing to these reserved bit, no any impact happened.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
CC: Andy Fleming <afleming@gmail.com>
CC: Marek Vasut <marex@denx.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Use the function 'mmc_send_status' to check the card status.
only when the card is ready, driver can send the next erase command
to the card, otherwise, the erase will failed:
=> mmc erase 0 1
MMC erase: dev # 0, block # 0, count 1 ... 1 blocks erase: OK
=> mmc erase 0 2
MMC erase: dev # 0, block # 0, count 2 ... mmc erase failed
1 blocks erase: ERROR
=> mmc erase 0 4
MMC erase: dev # 0, block # 0, count 4 ... mmc erase failed
1 blocks erase: ERROR
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
CC: Andy Fleming <afleming@gmail.com>
CC: Marek Vasut <marex@denx.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This code adds call to mmc_init(), for partition related commands (e.g.
fatls, fatinfo etc.).
It is safe to call mmc_init() multiple times since mmc->has_init flag
prevents from multiple initialization.
The FAT related code calls get_dev high level method and then uses
elements from mmc->block_dev, which is uninitialized until the mmc_init
(and thereof mmc_startup) is called.
This problem appears on boards, which don't use mmc as the default
place for envs
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
mmc_set_clock is set to the hard-coding.
But i think good that use the tran_speed value.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
In anticipation of Tegra3 support, continue removing/renaming
Tegra2-specific files. No functional changes (yet).
Updated copyrights to 2012.
Signed-off-by: Tom Warren <twarren@nvidia.com>
* 'master' of git://git.denx.de/u-boot-arm: (167 commits)
OMAP4/5: Change omap4_sdp, omap4_panda, omap5_evm maintainer
ARM: omap3: Add CONFIG_SPL_BOARD_INIT for CONFIG_SPL_MMC_SUPPORT
ARM: omap3: Set SPL stack size to 8KB, image to 54KB.
arm, omap3: fix warm reset serial output on OMAP36xx/AM/DM37xx
OMAP4: Set fdt_high for OMAP4 devices to enable booting with Device Tree
omap4: do not enable auxiliary cores
omap4: do not enable fs-usb module
omap4: panda: disable uart2 pads during boot
igep00x0: change mpurate from 500 to auto
igep00x0: enable the use of a plain text file
tegra2: trivially enable 13 mhz crystal frequency
tegra: Enable keyboard for Seaboard
tegra: Switch on console mux and use environment for console
tegra: Add tegra keyboard driver
tegra: fdt: Add keyboard definitions for Seaboard
tegra: fdt: Add keyboard controller definition
tegra: Add keyboard support to funcmux
input: Add support for keyboard matrix decoding from an fdt
input: Add generic keyboard input handler
input: Add linux/input.h for key code support
fdt: Add fdtdec functions to read byte array
tegra: Enable LP0 on Seaboard
tegra: fdt: Add EMC data for Tegra2 Seaboard
tegra: i2c: Add function to find DVC bus
fdt: tegra: Add EMC node to device tree
tegra: Add EMC settings for Seaboard
tegra: Turn off power detect in board init
tegra: Set up warmboot code on Nvidia boards
tegra: Setup PMC scratch info from ap20 setup
tegra: Add warmboot implementation
tegra: Set up PMU for Nvidia boards
tegra: Add PMU to manage power supplies
tegra: Add EMC support for optimal memory timings
tegra: Add header file for APB_MISC register
tegra: Add tegra_get_chip_type() to detect SKU
tegra: Add flow, gp_padctl, fuse, sdram headers
tegra: Add crypto library for warmboot code
tegra: Add functions to access low-level Osc/PLL details
tegra: Move ap20.h header into arch location
Add AES crypto library
i2c: Add TPS6586X driver
Add abs() macro to return absolute value
fdt: Add function to return next compatible subnode
fdt: Add function to locate an array in the device tree
i.MX28: Avoid redefining serial_put[cs]()
i.MX28: Check if WP detection is implemented at all
i.MX28: Add battery boot components to SPL
i.MX28: Reorder battery status functions in SPL
i.MX28: Add LRADC init to i.MX28 SPL
i.MX28: Add LRADC register definitions
i.MX28: Shut down the LCD controller before reset
i.MX28: Add LCDIF register definitions
i.MX28: Implement boot pads sampling and reporting
i.MX28: Improve passing of data from SPL to U-Boot
M28EVK: Add SD update command
M28EVK: Implement support for new board V2.0
FEC: Abstract out register setup
MX5: PAD_CTL_DRV_VOT_LOW and PAD_CTL_DRV_VOT_HIGH exchanged
i.MX28: Add delay after CPU bypass is cleared
spi: mxs: Allow other chip selects to work
spi: mxs: Introduce spi_cs_is_valid()
mx53loco: Remove unneeded gpio_set_value()
mx53loco: Add CONFIG_REVISION_TAG
mx53loco: Turn on VUSB regulator
mx53loco: Add mc34708 support and set mx53 frequency at 1GHz
pmic: dialog: Avoid name conflicts
imx: Add u-boot.imx as target for ARM9 i.MX SOCs
i.MX2: Include asm/types.h in arch-mx25/imx-regs.h
imx: usb: There is no such register
i.MX25: usb: Set PORTSCx register
imx: nand: Support flash based BBT
i.MX25: This architecture has a GPIO4 too
i.MX25: esdhc: Add mxc_get_clock infrastructure
i.MX6: mx6q_sabrelite: add SATA bindings
i.MX6: add enable_sata_clock()
i.MX6: Add ANATOP regulator init
mx28evk: add NAND support
USB: ehci-mx6: Fix broken IO access
M28: Scan only first 512 MB of DRAM to avoid memory wraparound
Revert "i.MX28: Enable additional DRAM address bits"
M28: Enable FDT support
mx53loco: Add support for 1GHz operation for DA9053-based boards
mx53loco: Allow to print CPU information at a later stage
mx5: Add clock config interface
imx-common: Factor out get_ahb_clk()
i.MX6Q: mx6qsabrelite: Add keypress support to alter boot flow
mx31pdk: Allow booting a zImage kernel
mx6qarm2: Allow booting a zImage kernel
mx6qsabrelite: Allow booting a zImage kernel
mx28evk: Allow booting a zImage kernel
m28evk: Allow to booting a dt kernel
mx28evk: Allow to booting a dt kernel
mx6qsabrelite: No need to set the direction for GPIO3_23 again
pmic: Add support for the Dialog DA9053 PMIC
MX53: mx53loco: Add SATA support
MX53: Add support to ESG ima3 board
SATA: add driver for MX5 / MX6 SOCs
MX53: add function to set SATA clock to internal
SATA: check for return value from sata functions
MX5: Add definitions for SATA controller
NET: fec_mxc.c: Add a way to disable auto negotiation
Define UART4 and UART5 base addresses
EXYNOS: Change bits per pixel value proper for u-boot.
EXYNOS: support TRATS board display function
LCD: support S6E8AX0 amoled driver based on EXYNOS MIPI DSI
EXYNOS: support EXYNOS MIPI DSI interface driver.
EXYNOS: support EXYNOS framebuffer and FIMD display drivers.
LCD: add data structure for EXYNOS display driver
EXYNOS: add LCD and MIPI DSI clock interface.
EXYNOS: definitions of system resgister and power management registers.
SMDK5250: fix compiler warning
misc:pmic:samsung Convert TRATS target to use MAX8997 instead of MAX8998
misc:pmic:max8997 MAX8997 support for PMIC driver
TRATS: modify the trats's configuration
ARM: Exynos4: ADC: Universal_C210: Enable LDO4 power line for ADC measurement
EXYNOS: Rename exynos5_tzpc structure to exynos_tzpc
arm: ea20: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
arm: cam_enc_4xx: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
cm-t35: add I2C multi-bus support
include/configs: Remove CONFIG_SYS_64BIT_STRTOUL
include/configs: Remove CONFIG_SYS_64BIT_VSPRINTF
omap3: Introduce weak misc_init_r
omap730p2: Remove empty misc_init_r
omap5912osk: Remove empty misc_init_r
omap4+: Remove CONFIG_ARCH_CPU_INIT
omap4: Remove CONFIG_SYS_MMC_SET_DEV
OMAP3: pandora: drop console kernel argument
OMAP3: pandora: revise GPIO configuration
...
If the WP function is NULL, simply assume the card is always RW.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Make the sysctrl structure common, so that it can
be used in generic functions across socs.
Also change the base address of the system control module, to
include all the registers and not simply the io regs.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Add parameters to the OMAP MMC initialization function so the board can
mask host capabilities and set the maximum clock frequency. While the
OMAP supports a certain set of MMC host capabilities, individual boards
may be more restricted and the OMAP may need to be configured to match
the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example.
Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
In driver mmc, generic s5p_sdhci code is implemented.
s5p_mmc file is dupulicated.
we are good that use the generic sdhci.
This patch supported the sdhci for Samsung-SoC.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Lei Wen<leiwen@marvell.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
To support the Samsung-SoC, added the basically functions.
Samsung-SoC didn't used the SDHCI_CTRL_HISPD.
And added set_control_reg callback for s3c64xx.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Lei Wen<leiwen@marvell.com>
When response type is R1b, mask value is added the SDHCI_INT_DAT_END.
but in while(), didn't check that flag.
So sdhci controller didn't work fine.
CMD6 didn't always complete.
So add the quirks for broken r1b response
and add the timeout value to prevent the infinite loop.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Lei Wen<leiwen@marvell.com>
Some MMC cards, like my ancient 32.0MB SanDisk RS-MMC cards had issue if b_max
was set to 0x40 and DMA was enabled. Lower this value to 0x20, which allows
these cards to work too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>