The card_caps bit should denote the card capability to use DDR mode,
but we need the flag indicating that the DDR mode is active.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Block length for write and read commands is fixed to 512 bytes
when the card is in Dual Data Rate mode. If block length read from CSD
is different, make sure the driver will use correct length
in all further calculations and settings.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Since the driver doesn't work in 1.2V or 1.8V signaling level modes,
Dual Data Rate mode can be supported by the driver only if it is supported
by the card in regular 3.3V mode. So, check for a particular single
bit in card type field.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
If the MMC_MODE_DDR_52MHz flag is set in card capabilities bitmask,
it is never cleared, even if switching to DDR mode fails, and if
the controller driver uses this flag to check the DDR mode, it can
take incorrect actions.
Also, DDR related checks in mmc_startup() incorrectly handle the case
when the host controller does not support some bus widths (e.g. can't
support 8 bits), since the host_caps is checked for DDR bit, but not
bus width bits.
This fix clearly separates using of card_caps bitmask, having there
the flags for the capabilities, that the card can support, and actual
operation mode, described outside of card_caps (i.e. bus_width and
ddr_mode fields in mmc structure). Separate host controller drivers
may need to be updated to use the actual flags. Respectively,
the capabilities checks in mmc_startup are made more correct and clear.
Also, some clean up is made with errors handling and code syntax layout.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
if the card claims to be high capacity and the card
is partitioned the capacity shall still be read from
ext_csd SEC_COUNT even if the resulting capacity is
smaller than 2 GiB
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
If print_mmc_devices() was called with a '\n' separator (as done
for example by the "mmc list" command), it offset the 2-nd and
all subsequent lines by one space. Fixing this.
Signed-off-by: Lubomir Popov <l-popov@ti.com>
Boards using the TWL4030 regulator may not all use the LDOs the same way
(e.g. MMC2 power can be controlled by another LDO than VMMC2).
This delegates TWL4030 MMC power initializations to board-specific functions,
that may still call twl4030_power_mmc_init for the default behavior.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
[trini: Fix omap3_evm warning, add twl4030.h]
Signed-off-by: Tom Rini <trini@ti.com>
Renesas R-Mobile/R-Car ARM SoC of MMC has the same IP that are supported by
sh_mmcif. This adds support R-Mobile/R-Car ARM SoC with the setting of the
clock support.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Maximum value and the minimum value of clock for sh_mmcif instead by
base of MMC clock. This removes fixed clock, make the changes to be calculated
according to environment.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Use DIV_ROUND_UP and fls to simplify the code.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Not every device has multiple MMC slots available, so it makes sense to enable
only the required LDOs for the available slots. Generic code in omap_hsmmc will
enable both VMMC1 and VMMC2, in doubt.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
Some devices may use non-standard combinations of regulators to power MMC:
this allows these devices to provide a board-specific MMC power init function
to set everything up in their own way.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
just add a few ifdefs around because this
device is very similar to dra7xxx.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
The reset value of "uSDHCx_INT_STATUS_EN" register is changed to 0
on iMX6SX. So the fsl_esdhc driver must update to set the register,
otherwise no state can be detected.
Signed-off-by: Ye.Li <B37916@freescale.com>
for multi instance API we use struct fsl_esdhc_cfg to
pass the clock rate. Do not set f_max from global data,
since this is wrong for multi instance case.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Switch the default CD GPIO polarity to active low.
The current hsmmc driver assumption that the CD GPIO is active high, but
in the real hardware, usually the opposite holds.
The usual SD card socket has a mechanical switch which is grounded as
soon as a card is inserted.
Of course there might be some board logic which inverts the signal, but
as far as current users are concerned, there is no such logic.
Current U-Boot users either not using the CD functionality, or have a
different way (e.g. external to SoC GPIO controller) for checking the
card presence.
This patch also brings the polarity assumption in line with the Linux
kernel and adds appropriate comments.
This patch also might spare issues once the TWL GPIO driver will be
converted to the DM.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
This is necessary for the device-model enabled builds to work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Mostly automatic with:
sed -i -e 's/CONFIG_\(SUN[45678]I\)/CONFIG_MACH_\1/g' $(git grep -l CONFIG_SUN[45678]I)
followed by removing the relevant #defines from include/configs/sun?i.h by
hand.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The SD Card slot detection pin should be configured as input.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Allwinner A23 SoC has reset controls like the A31 (sun6i).
The FIFO address is also the same as sun6i.
Re-use code added for sun6i.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
sunxi SOCs can boot from both mmc0 and mmc2, detect from which one we're
booting, and make that one "mmc dev 0" so that a single u-boot binary can
be used for both the onboard eMMC and for external sdcards.
When we're booting from mmc2, we make it dev 0 because that is where the SPL
will load the tertiary payload (the actual u-boot binary in our case) from,
see: common/spl/spl_mmc.c, which has dev 0 hardcoded everywhere.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The mmc hardware on sun6i has an extra reset control that needs to
be de-asserted prior to usage. Also the FIFO address is different.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[wens@csie.org: use setbits_le32 for reset control, drop obsolete changes,
rewrite different FIFO address handling, add commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Allwinner A20/A23/A31's SD/MMC host support SDHC High Capacity feature.
Signed-off-by: Wills Wang <wills.wang.open@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add driver model support to this driver, while retaining support for the
legacy system. Driver model GPIO support is enabled with CONFIG_DM_GPIO
as usual.
Since gpio_is_valid() no longer exists, we can use the -EINVAL error
returned from gpio_request().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
With driver model GPIOs must be requested before use. Make sure this is
done correctly.
(Note that the soft SPI part of universal is omitted, since this driver
is about to be replaced with a driver-model-aware version)
Signed-off-by: Simon Glass <sjg@chromium.org>
During rigorous testing of our latest update infrastructure I came
across quite consistent timeouts on certain eMMC parts (e.g. Hynix
H26M21001ECR) when writing big (e.g. in excess of 400 MB) file system
images:
MMC write: dev # 0, block # 40960, count 944128 ...
mmc_send_cmd_bounced: MMC Timeout
Interrupt status 0x00000001
Interrupt status enable 0xdfff003b
Interrupt signal enable 0xdfff0002
Present status 0x01870106
mmc write failed
Comparing the various data sheets I came across the following timeout
specification:
Secure Erase/TRIM Timeout=300ms*2*10=6000ms
Unfortunately empirical testing still failed albeit much more rarely.
Increasing the timeout to 8000ms made it finally disappear entirely.
This patch allows us writing various eMMC parts without seeing any
further issues.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Change this board to add a device tree.
This also adds a pinmux header file although it is not used as yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Make the SoCFPGA MMC stub pick clock via the clock manager
frequency accessors instead of hard-coding the frequency.
Also fix calloc() misuse.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The dw_mmc driver was responding to errors with debug(). Change that
to prinf()/puts() respectively so that any errors are immediately
obvious. Also adjust english in comments.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Chin Liang See <clsee@altera.com>
dw_mmc driver was responding to errors with debug(). Change that to
prinf so that any errors are immediately obvious. Also adjust english
in comments.
Signed-off-by: Pavel Machek <pavel@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
After setting the bus width, the extended CSD register is read. Some selected
fields are compared with previously read extended CSD register fields. In this
comparison the EXT_CSD_ERASE_GROUP_DEF field is compared. But this field is
previously written under certain circumstances. And then the comparison fails.
Only compare read-only fields. Therefore compare field EXT_CSD_HC_WP_GRP_SIZE
instead of field EXT_CSD_ERASE_GROUP_DEF.
Signed-off-by: Mario Schuknecht <mario.schuknecht@dresearch-fe.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
In function mvebu_mmc_write notice command timeout. It is possible that a
command is done, but a timeout occurred.
Enable timeout in set bus function.
Set window registers. Without that I could not use the driver on a Kirkwood
88F6282 SoC.
Set high capacity and 52MHz driver feature.
Signed-off-by: Mario Schuknecht <mario.schuknecht@dresearch-fe.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The capacity and lba for an MMC device with part_num 0 reflects the
whole device. When mmc_switch_part() successfully switches to a
partition, the capacity is changed to that partition. As partition 0
does not physically exist, attempts to switch back to the whole device
will indicate an error, but the capacity setting for the whole device
must still be restored to match the partition.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Tested-by: Tom Rini <trini@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
if we set manually this bit on the eMMC card using mmc_switch(...),
we also have to set it within our (before read) internal structure
'ext_csd'.
Otherwise following checks on this will fail.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Wait data transfer till the data end bit other than the data block end
bit is set.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
This would be useful to start moving various config options.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
For LS1, esdhc is big-endian IP. Accessing the registers
should be in big-endian mode. So we use esdhc_read32()
to read Host controller capabilities register for LS1.
For LS1, when using CMD12, cmdtype need to be set to
ABORT, otherwise, next read command will hang.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Structure defining clock manager hardware was wrong, leading to
wrong registers being accessed and hang in MMC init.
This fixes structure to match hardware.
Signed-off-by: Pavel Machek <pavel@denx.de>
If the MCI IP version >= 0x300, it supports hight speed mode
option, this patch enable it.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The mode register is different between MCI IP version.
So, according to MCI IP version to set the mode register.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
To fix the clock divider calculation error when the controller
clock same as the operating frequency. This is known as bypass
mode. In this mode, the divider should be 0.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Implement SD driver for the S3C24xx family. This implementation
is currently only capable of using the PIO transfers, DMA is not
supported.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Seems like the controller doesn't support the flag. None of the hi-speed cards
I've tried could be read, while they successfully worked with the quirk enabled.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
This patch add Marvell kirkwood MVSDIO/MMC driver
and enable it for Sheevaplugs and OpenRD boards.
Signed-off-by: Gerald Kerma <drEagle@doukki.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Add missing prototypes for global functions and
make local functions static.
cc: panto@antoniou-consulting.com
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
The DMA code in sunxi_mmc.c is broken. mmc_trans_data_by_dma() allocates the
dma descriptors on the stack, and then exits while the dma transfer is in
progress, so the dma engine is reading stack memory which at that point may
be re-used. So far we've gotten away with this by luck, but recent u-boot
changes have shifted the stack start address by 16 bytes, which combined
with dma alignment now exposes this problem.
Since we end up just busy waiting for the dma engine anyway, this commit
fixes things by simply removing the dma code, resulting in smaller bug-free
code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
commit 18b06652cd "tools: include u-boot version of sha256.h"
unconditionally forced the sha256.h from u-boot to be used
for tools instead of the host version. This is fragile though
as it will also include the host version. Therefore move it
to include/u-boot to join u-boot/md5.h etc which were renamed
for the same reason.
cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Cleanup to balance malloc/free calls.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Rather than just returning -1 everywhere, try to return something
meaningful from mmc_select_hwpart(). Note that most other MMC functions
don't do this, including functions called from mmc_select_hwpart(), so
I'm not sure how effective this will be. Still, it's one less place with
hard-coded -1.
Suggested-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
On Mon, 2014-05-05 at 14:18 +0200, Stefan Roese wrote:
> > + case 1:
> > +#if CONFIG_MMC1_PG
> Are you sure that this is correct and shouldn't be:
>
> +#ifdef CONFIG_MMC1_PG
>
> ?
It's "correct" in so far as it works (the boards.cfg config stuff
#defines things to 1), but I think you are right that it isn't the
preferred style. But...
> A quick scan through this patch series shows that this define
> is not set at all. Perhaps its outdated? Or is it used to support
> some other sunxi SoC? Not sure, perhaps it should be removed for
> now.
...I had thought that it was to support some other board which wasn't
being upstreamed right now, so eventually useful and harmless for now,
but I've just checked and it isn't actually used by any of the boards in
u-boot-sunxi.git. So rather than fix it to use #ifdef lets drop it.
Rather than resend the entire series, here is v5.1 of this patch.
> Other than this please add my:
>
> Reviewed-by: Stefan Roese <sr@denx.de>
Thanks!
8<---------------------------------
>From 20704e35a41664de5f516ed0e02981ac06085102 Mon Sep 17 00:00:00 2001
From: Ian Campbell <ijc@hellion.org.uk>
Date: Fri, 7 Mar 2014 04:29:39 +0000
Subject: [PATCH v5.1 7/8] sunxi: mmc support
This adds support for the MMC controller on the Allwinner A20 (sun7i)
processor.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Wills Wang <wills.wang.open@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Cc: Aaron Maoye <leafy.myeh@allwinnertech.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: Tom Rini <trini@ti.com>
In 7168977 we made calls to check_and_invalidate_dcache_range()
conditional on !CONFIG_SYS_FSL_ESDHC_USE_PIO. Only define this function
in this case as well.
Signed-off-by: Tom Rini <trini@ti.com>
This enables specifying which eMMC HW partition to target for any U-Boot
command that uses the generic get_partition() function to parse its
command-line arguments.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds functions for read, write and authentication
key programming for the Replay Protected Memory Block partition
in the eMMC.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
MMC switch command for unsupported feature (e.g. bus width) sets a switch
error bit in card status. This bit should be checked, and, if it's set,
no access with new controller settings should be performed.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
When configure the fsl_esdhc driver to PIO mode by defining
"CONFIG_SYS_FSL_ESDHC_USE_PIO", the SD/MMC read and write will fail.
Two bugs in the driver to cause the issue:
1. The read buffer was invalidated after reading from DATAPORT register,
which should be only applied to DMA mode. The valid data in cache was
overwritten by physical memory.
2. The watermarks are not set in PIO mode, will cause according state not
be set.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Conflicts:
boards.cfg
Conflicts were trivial once u-boot-arm/master boards.cfg was
reformatted (commit 6130c146) to match u-boot/master's own
reformatting (commit 1b37fa83).
To reuse the code, added the s5p_sdhci_core_init function.
Before applied this patch, didn't use the 8-bit mode at exynos baord.
Because it didn't set "MMC_MODE_8BIT".
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Restore the platdata(property of dt) into host struct.
Then data's information is maintained and reused anywhere.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
If CONFIG_API is ever to be enabled on Tegra, this define must be set,
since api/api_storage.c uses it.
A couple of annoyting things about CONFIG_SYS_MMC_MAX_DEVICE
1) It isn't documented in README. The same is true for a lot of similar
defines used by api_storage.c.
2) It doesn't represent MAX_DEVICE but rather NUM_DEVICES, since the
valid values are 0..n-1 not 0..n.
However, I this patch does not address those shortcomings.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
T4240RDB board Specification
----------------------------
Memory subsystem:
6GB DDR3
128MB NOR flash
2GB NAND flash
Ethernet:
Eight 1G SGMII ports
Four 10Gbps SFP+ ports
PCIe:
Two PCIe slots
USB:
Two USB2.0 Type A ports
SDHC:
One SD-card port
SATA:
One SATA port
UART:
Dual RJ45 ports
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: fix CONFIG_SYS_QE_FMAN_FW_ADDR in T4240RDB.h]
Add support of loading image, binary for MMC and SPI during SPL boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Fix following compile warnings
fsl_esdhc_spl.c: In function 'mmc_boot':
fsl_esdhc_spl.c:35:10: warning: unused variable 'byte_num' [-Wunused-variable]
fsl_esdhc_spl.c:35:7: warning: unused variable 'i' [-Wunused-variable]
fsl_esdhc_spl.c:34:8: warning: unused variable 'val' [-Wunused-variable]
fsl_esdhc_spl.c:33:6: warning: unused variable 'blklen' [-Wunused-variable]
fsl_esdhc_spl.c:105:7: warning: 'tmp_buf' may be used uninitialized in this
function [-Wuninitialized]
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. The Data timeout counter value in eSDHC_SYSCTL register is
not working as it should be, so add quirks to enable this
workaround to fix it to the max value 0xE.
2. Add CONFIG_SYS_FSL_ERRATUM_ESDHC111 to enable its workaround.
* Update of patch for change mmc interface by
Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The controller reset is performed now if command error occurs.
This commit adds the reset for the case of data related errors too.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Calculation of the timeout value should be based on actual clock value,
written to controller registers. Since mmc->tran_speed is either the
maximum allowed speed, or the preliminary value, that is be not yet
set to registers, the actual timeout, taken by the controller, based
on its clock settings, may be much longer than expected, based on
mmc->tran_speed value. In particular it happens at early initialization
stage, when typical value of mmc->tran_speed is 20MHz or 26MHz, while
actual clock setting, configured in the controller, is 400kHz.
It's more correct to use mmc->clock value for timeout calculation instead.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Some eMMC chips may need the RST_n_FUNCTION bit set to a non-zero value
in order for warm reset of the system to work. Details on this being
required will be part of the eMMC datasheet. Also add using this
command to the dra7xx README.
* Whitespace fix by panto
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
In the recent mmc cleanup, the mmc_host_is_spi macro was broken and
bfin_sdh.c had mmc->bus_width turned into mmc_bus_width(mmc), both of
which were incorrect.
Signed-off-by: Tom Rini <trini@ti.com>
The way that struct mmc was implemented was a bit of a mess;
configuration and internal state all jumbled up in a single structure.
On top of that the way initialization is done with mmc_register leads
to a lot of duplicated code in drivers.
Typically the initialization got something like this in every driver.
struct mmc *mmc = malloc(sizeof(struct mmc));
memset(mmc, 0, sizeof(struct mmc);
/* fill in fields of mmc struct */
/* store private data pointer */
mmc_register(mmc);
By using the new mmc_create call one just passes an mmc config struct
and an optional private data pointer like this:
struct mmc = mmc_create(&cfg, priv);
All in tree drivers have been updated to the new form, and expect
mmc_register to go away before long.
Changes since v1:
* Use calloc instead of manually calling memset.
* Mark mmc_register as deprecated.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>