A few boards had not been fully re-synced with CONFIG_ARCH_MX5 / CONFIG_MX51 /
CONFIG_MX53 being in Kconfig. Do so now.
Signed-off-by: Tom Rini <trini@konsulko.com>
PSCI can be used on both multiple and single core socs. Current
implementation only allows PSCI to work on multiple core socs.
This patch removes this restriction so that PSCI can work on
single core socs as well.
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add Kconfig option to support loading PPA header from eMMC/SD and
NAND Flash.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The R40's CPU controls are a combination of sun6i and sun7i.
All controls are in the CPUCFG block, and it seems the R40 does not
have a PRCM block. The core reset, power gating and clamp controls
are grouped like sun6i.
Last, the R40 does not have a secure SRAM block.
This patch adds a PSCI implementation for CPU bring-up and hotplug
for the R40.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Imports ARM SMC Calling Convention code from Linux 4.11-rc6.
The files have been copied as follows:
[Linux] [U-Boot]
arch/arm/kernel/smccc-call.S -> arch/arm/cpu/armv7/smccc-call.S
arch/arm64/kernel/smccc-call.S -> arch/arm/cpu/armv8/smccc-call.S
arch/arm/include/asm/opcodes* -> arch/arm/include/asm/opcodes*
include/linux/arm-smccc.h -> include/linux/arm-smccc.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Current sysclk fixing would fix all clocks with 'fixed-clock' compatible.
This patch is to fix sysclk by path to avoid any incorrect fixing.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Number of TZASC instances may vary across NXP SoCs.
So put TZASC configuration under instance specific defines.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
- Add SD secure boot target for ls1043ardb.
- Implement FSL_LSCH2 specific spl_board_init() to setup CAAM stream
ID and corresponding stream ID in SMMU.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size as
header is appended to u-boot image. So header will also be copied
from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
(128K) where 32K are reserved for use by boot ROM and 6K for secure
boto header.
- Error messages during SPL boot are limited to error code numbers
instead of strings to reduce the size of SPL image.
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Define bootscript and its header addresses for QSPI target
Also add PPA header address in Kconfig
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The header address of PPA defined in Kconfig.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Rename CONFIG_FSL_DCU_FB to CONFIG_VIDEO_FSL_DCU_FB
and convert it to Kconfig.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
This function name shadows a global name but is in fact different. This
is very confusing. Rename it to help with the following refactoring.
Signed-off-by: Simon Glass <sjg@chromium.org>
Logic PD has an i.MX6Q system on module (SOM) with a development kit. The
SOM has a built-in microSD socket, DDR and NAND flash. The development kit
has an SMSC Ethernet PHY, serial debug port and a variety of peripherals.
This have been verified to boot the i.MX6Q version over either SD
on the development kit or NAND built into the SOM. Items in the dtsi file
are specific to the SOM itself. Items in the dts file are in the baseboard.
Future versions of the SOM will come out supporting the same basebord and
potentially future base boards will come out supporting the same SOM.
Signed-off-by: Adam Ford <aford173@gmail.com>
The num/denom is a float value, but in the calculation it is convert
to integer 0, and wrong result.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
spl_mmc.c calls mmc_initialize(). This symbol is provided in
drivers/mmc/mmc.c when CONFIG_GENERIC_MMC is enabled.
The sunxi Kconfig case is an oddball because it redefines
SPL_MMC_SUPPORT.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
[trini: Update arch/arm/cpu/armv8/zynqmp/Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
With d53ecad92f some unused interrupt related code was removed.
However all of these options are currently unused. Rather than migrate
some of these options to Kconfig we just remove the code in question.
The only related code changes here are that in some cases we use
CONFIG_STACKSIZE in non-IRQ related context. In these cases we rename
and move the value local to the code in question.
Fixes: d53ecad92f ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi")
Signed-off-by: Tom Rini <trini@konsulko.com>
By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
At present we cannot use this function as an init sequence call without a
wrapper, since it returns the RAM size. Adjust it to set the RAM size in
global_data instead, and return 0 on success.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
It looks like only cm5200 and tqm8xx use this feature, so we don't really
need it in generic code. Drop it and have the users access gd->board_type
directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Some Freescale boards used an extra version of the constant to hold the
Generic Timer frequency. This can easily be covered by the now unified
COUNTER_FREQUENCY constant, so remove this extra variable from those
boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Many ARMv8 boards define a constant COUNTER_FREQUENCY to specify the
frequency of the ARM Generic Timer (aka. arch timer).
ARMv7 boards traditionally used CONFIG_TIMER_CLK_FREQ for the same
purpose. It seems useful to unify them.
Since there are less occurences of the latter version, lets convert all
users over to COUNTER_FREQUENCY.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
USB requires 100MHz clock. On LS1012A, a dedicated 100MHz is provided
instead of SYSCLK (125MHz). Skipping checking SYSCLK for FDT fixup.
Signed-off-by: Yingxi Yu <yingxi.yu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The LS2088A series SoCs has different physical memory map address and
CCSR registers address against LS2080A series SoCs.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This i2c errata only applies to LS2080A and its variants, namely
LS2080A, LS2085A and LS2088A.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
SerDes information is not necessary to be present in RCWSR29 register.
It may vary from SoC to SoC.
So Avoid RCWSR28 register hard-coding.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
MAC number used per QSGMII is not fixed. It may wary from SoC to SoC.
So move QSGMII wriop_init_dpmac() to SoC file.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Erratum A009635 is valid only for LS2080A SoC and its
personality. Add SoC svr check.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Select missing BOARD_LATE_INIT from configs/ to
respective targets on arch area for Engicam imx6 boards.
Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Move Freescale/NXP Vybrid to a standard arch/board approach, similar
to what has been done to i.MX 6 earlier in commit 89ebc82137 ("ARM:
mx6: move to a standard arch/board approach").
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
According to the MX7D fuse map the following speed grades are available:
800 MHz
500 MHz
1000 MHz
1200 MHz
So simply return the real frequency that corresponds to the speed grade.
With this change we see on boot:
CPU: Freescale i.MX7D rev1.2 1000 MHz (running at 792 MHz)
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
According to the MX7D fuse map the speed grade of the parts, which
return '1' is 500MHz instead of 850MHz, so fix it accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
OPOS6UL is an i.MX6UL based SoM with 256MB RAM, 4GB eMMC and an ethernet
phy. OPOS6ULDev is carrier board for the OPOS6UL.
U-Boot SPL 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09)
Trying to boot from MMC1
U-Boot 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09 +0100)
CPU: Freescale i.MX6UL rev1.0 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 40C
Reset cause: POR
Model: Armadeus Systems OPOS6UL SoM on OPOS6ULDev board
DRAM: 256 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Video: 800x480x18
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Today, we have cases where we wish to build all of U-Boot in Thumb2 mode for
various reasons. We also have cases where we only build SPL in Thumb2 mode due
to size constraints and wish to build the rest of the system in ARM mode. So
in this migration we introduce a new symbol as well, SPL_SYS_THUMB_BUILD to
control if we build everything or just SPL (or in theory, just U-Boot) in
Thumb2 mode.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Boot from MMC:
-------------
U-Boot SPL 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33)
Trying to boot from MMC1
U-Boot 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33 +0100)
CPU: Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 33C
Reset cause: POR
Model: Engicam Is.IoT MX6UL Starterkit
DRAM: 512 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
isiotmx6ul>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add CAAM clock functions, SEC_CONFIG[1] fuse checking, and default CSF
size for HAB support boot on mx7ulp.
Users need to uncomment the CONFIG_SECURE_BOOT in mx7ulp_evk.h to build
secure uboot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Drop CONFIG_LPUART_32B_REG.
Move the register structure to a common file include/fsl_lpuart.h
Define lpuart_serial_platdata structure which includes the reg base and flags.
For 32Bit register access, use lpuart_read32/lpuart_write32 which handles
big/little endian.
For 8Bit register access, still use the orignal code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Shaohui Xie <Shaohui.Xie@nxp.com>
Cc: Alison Wang <b18965@freescale.com>
Implement the i2c clock enable and get function for mx7ulp. These
functions are required by imx_lpi2c driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Implement soc level functions to get cpu rev, reset cause, enable cache,
etc. We will disable the wdog and init clocks in s_init at very early u-boot
phase.
Since the we are seeking the way to get chip id for mx7ulp, the get_cpu_rev
is hard coded to a fixed value. This may change in future.
Reuse some code in imx-common.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add a clock framework to support SCG1/PCC2/PCC3 for A7 to support get/set
clock source, divider, clock rate and parent source.
Users need to include pcc.h to use the APIs to for peripherals clock. Each
peripheral clock is defined in enum pcc_clk type.
SCG relevants APIs are defined in scg.h which supports clock rate get, PLL/PFD
enablement and settings, and all SCG clock initialization. User need use enum
scg_clk to access each clock source.
In clock.c, we initialize necessary clocks at u-boot s_init and implement the
clock functions used by driver modules to operate clocks dynamically.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add a new driver under ULP directory to support its IOMUXC
controllers. The ULP has two IOMUXC, the IOMUXC0 is used
for M4 domain, while IOMUXC1 is for A7. We set IOMUXC1 as
the default IOMUX in this driver. Any pins in IOMUXC0 needs
to configure with IOMUX_CONFIG_MPORTS in its mux_mode field.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
i.MX7ULP is a new series SoC which has different architecture
from previous i.MX platforms. Create a new cpu folder for it,
and add it to Kconfig.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
The SysTick is a 24-bit down counter that is found on all ARM Cortex
M3, M4, M7 devices and is always located at a fixed address.
The number of reference clock ticks that correspond to 10ms is normally
defined in the SysTick Calibration register's TENMS field. However, on some
devices this is wrong, so this driver allows the clock rate to be defined
using CONFIG_SYS_HZ_CLOCK.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Vikas MANOCHA <vikas.manocha@st.com>
The workaround for ARM errata 725233 had been lost since
commit 45bf05854b (armv7: adapt omap3 to the new cache
maintenance framework). Bring it back in order to avoid
very difficult to reproduce, but actually encountered in
the wild CPU deadlocks when running software rendered
X11 desktop on OMAP3530 hardware.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Migrate to Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Read DMA operations causes CRC error on armv8 chassis 2 platforms
due to the erratum A-010635.
In order to support sata on these platforms, ECC needs to be disabled.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In early MMU table, DDR has to be mapped as device memory to avoid
speculative access. After DDR is initialized, it needs to be updated
to normal memory to allow code execution. To simplify the code,
dram_init() is moved into a common file as a weak function.
Signed-off-by: York Sun <york.sun@nxp.com>
Function mmu_change_region_attr() is added to change existing mapping
with updated PXN, UXN and memory type. This is a break-before-make
process during which the mapping becomes fault (invalid) before final
attributres are set.
Signed-off-by: York Sun <york.sun@nxp.com>
Early MMU improves performance especially on emulators. However, the
early MMU is left enabled after the first stage of SPL boot. Instead
of flushing D-cache and dealing with re-enabling MMU for the second
stage U-Boot, disabling it for SPL build simplifies the process. The
performance penalty is unnoticeable on the real hardware. As of now,
SPL boot is not supported by existing emulators. So this should have
no impact on emulators.
Signed-off-by: York Sun <york.sun@nxp.com>
This patch follows the break-before-make process when making changes
to MMU table. MMU is disabled before changing TTBR to avoid any
potential race condition.
Signed-off-by: York Sun <york.sun@nxp.com>
Update mapping with actual DDR size. Non-existing memory should not
be mapped as "normal" memory to avoid speculative access.
Signed-off-by: York Sun <york.sun@nxp.com>
For ARMv8 Layerscape SoCs, secure memory and MC memorey are reserved
at the end of DDR. DDR is spit into two or three banks. This patch
reverts commit aabd7ddb and simplifies the calculation of reserved
memory, and moves the code into common SoC file. Secure memory is
carved out first. DDR bank size is reduced. Reserved memory is then
allocated on the top of available memory. U-Boot still has access
to reserved memory as data transferring is needed. Device tree is
fixed with reduced memory size to hide the reserved memory from OS.
The same region is reserved for efi_loader.
Signed-off-by: York Sun <york.sun@nxp.com>
This moves all of the current ARM errata from various header files and in to
Kconfig. This allows for a minor amount of cleanup as we had some instances
where both a general common header file was enabling errata as well as the
board config. We now just select these once at the higher level in Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.
During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will
make the code more readable. Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.
This commit was created as follows:
[1] Edit "default n" to "default y" in the config entry in
common/Kconfig.
[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"
[3] Rename the instances in defconfigs by the following:
find . -path './configs/*_defconfig' | xargs sed -i \
-e '/CONFIG_SYS_NO_FLASH=y/d' \
-e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'
[4] Change the conditionals by the following:
find . -name '*.[ch]' | xargs sed -i \
-e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
-e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
-e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
-e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'
[5] Modify the following manually
- Rename the rest of instances
- Remove the description from README
- Create the new Kconfig entry in drivers/mtd/Kconfig
- Remove the old Kconfig entry from common/Kconfig
- Remove the garbage comments from include/configs/*.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
IFC IP clock is always a constant divisor of platform clock
pre-defined per SoC. Clock control register (CCR) used in
current implementation governs IFC IP output clock.
Update sys_info->freq_localbus to represent IFC input clock with
value constant divisor of platform clock.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This feature seems to be sometimes misunderstood. The intention is:
[1] Bring the slaves into the U-Boot proper image, not SPL (unless
you have a special reason to do otherwise).
[2] The operation must be done in a board (SoC) specific manner
since how to wake the slaves from the Boot ROM is SoC specific.
[3] The slaves must enter U-Boot proper after U-Boot relocates
itself because the "cpu-release-addr" property points to the
relocated memory area.
[2] is already explained in the help. We can make [1] even clearer
by mentioning "U-Boot proper" instead of "U-Boot". [3] is missing,
so I am adding it to the list. Instead, "before the master CPU
jumps to the kernel" is a matter of course, so removed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Moving arch/arm/mach-litesom/ to arch/arm/cpu/armv7/mx6/ was requested
in [1] during discussion of chiliSOM support patches.
[1] http://lists.denx.de/pipermail/u-boot/2017-January/279137.html
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This option should not really be user selectable. Note that on PowerPC
we currently only need BOARD_LATE_INIT when CHAIN_OF_TRUST is enabled so be
conditional on that.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> (for UniPhier)
Move all of the status LED feature to drivers/led/Kconfig.
The LED status definitions were moved from the board configuration
files to the defconfig files.
TBD: Move all of the definitions in the include/status_led.h to the
relevant board's defconfig files.
Tested boards: CL-SOM-AM57x, CM-T335
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
commit: 65f83802b7 "serial: 16550: Add getfcr accessor"
breaks u-boot commandline working with long commands
sending to the board.
Since the above patch, you have to setup the fcr register.
For board/archs which enable OF_PLATDATA, the new field
fcr in struct ns16550_platdata is not filled with a
default value ...
This leads in not setting up the uarts fifo, which ends
in problems, when you send long commands to u-boots
commandline.
Detected this issue with automated tbot tests on am335x
based shc board.
The error does not popup, if you type commands. You need
to copy&paste a long command to u-boots commandshell
(or send a long command with tbot)
Possible boards/plattforms with problems:
./arch/arm/cpu/arm926ejs/lpc32xx/devices.c
./arch/arm/mach-tegra/board.c
./board/overo/overo.c
./board/quipos/cairo/cairo.c
./board/logicpd/omap3som/omap3logic.c
./board/logicpd/zoom1/zoom1.c
./board/timll/devkit8000/devkit8000.c
./board/lg/sniper/sniper.c
./board/ti/beagle/beagle.c
./drivers/serial/serial_rockchip.c
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Moved the config FSL_PPA_ARMV8_PSCI from fsl-layerscape's Kconfig to
Kconfig under armv8 and renamed it to SEC_FIRMWARE_ARMV8_PSCI.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For 64-bit kernel, there is a warning about x1-x3 nonzero in violation
of boot protocol. To fix this issue, input argument 4 is added for
armv8_switch_to_el2 and armv8_switch_to_el1. The input argument 4 will
be set to the right value, such as zero.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The default MSI node in kernel tree is for LS1043A rev1.0 silicon, if
rev1.1 silicon used, need to fixup the MSI node to match it.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The LS1043A rev1.1 silicon supports two types of GIC offset: 4K
alignment and 64K alignment. The bit SCFG_GIC400_ALIGN[GIC_ADDR_BIT]
is used to choose which offset will be used.
The LS1043A rev1.0 silicon only supports the CIG offset with 4K
alignment.
If GIC_ADDR_BIT bit is set, 4K alignment is used, or else 64K alignment
is used. 64K alignment is the default setting.
Overriding the weak smp_kick_all_cpus, the new impletment is able to
detect GIC offset.
The default GIC offset in kernel device tree is using 4K alignment, it
need to be fixed if 64K alignment is detected.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
By default the SATA IP on the ls208Xa SoCs does not generating
coherent/snoopable transactions. This patch enable it in the
sata axicc register.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Set up chip power supply voltage according to voltage ID.
The fuse status register provides the values from on-chip
voltage ID fuses programmed at the factory. These values
define the voltage requirements for the chip.
Main operations:
1. Set up the core voltage
2. Set up the SERDES voltage and reset SERDES lanes
3. Enable/disable DDR controller support 0.9V if needed
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Without a prompt in Kconfig, SECURE_BOOT cannot be selected by
defconfig. The option was dropped unintentionally when defconfig
files were cleaned up. Three targets were impacted
ls1043ardb_SECURE_BOOT, ls2080ardb_SECURE_BOOT,
ls2080aqds_SECURE_BOOT.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch binds the sys_info->freq_systembus to Platform PLL, and
implements the IPs' clock function individually.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Up to now, there are 3 kind of SoCs under Layerscape Chassis 2,
like LS1043A, LS1046A and LS1012A. But the clocks tree has a
lot of differences, for instance, the IP modules have different
dividers to derive its clock from Platform PLL. And the core
cluster PLL and platform PLL maybe have different reference
clocks, such as LS1012A. Another problem is which clock/PLL
should be described by sys_info->freq_systembus, it is confused
in Layerscape Chissis 2.
This patch is to bind the sys_info->freq_systembus to the Platform
PLL, and handle the different divider of IP modules separately
between different SoCs, and separate reference clocks of core
cluster PLL and platform PLL.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For A53, data coherency is enabled only when the CPUECTLR.SMPEN bit is
set. The SMPEN bit should be set before enabling the data cache.
If not enabled, the cache is not coherent with other cores and
data corruption could occur.
For A57/A72, SMPEN bit enables the processor to receive instruction
cache and TLB maintenance operations broadcast from other processors
in the cluster. This bit should be set before enabling the caches and
MMU, or performing any cache and TLB maintenance operations.
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Clear the content to zero and the ECC error bit of OCRAM1/2.
The OCRAM must be initialized to ZERO by the unit of 8-Byte before
accessing it, or else it will generate ECC error. And the IBR has
accessed the OCRAM before this initialization, so the ECC error
status bit should to be cleared.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Pratiyush Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
It is recommended to set forced-order mode in RNI-6,
RNI-20 for performance optimization in LS2088A.
Both LS2080A, LS2088A families has CONFIG_LS2080A define.
As above update is required only for LS2088A, skip this
for LS2080A SoC family.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Using CONFIG_IS_ENABLED() doesn't work in SPL. This patch replaces the only
occurrence of CONFIG_IS_ENABLED() in start.S to a regular #if defined().
It also adds "&& !defined(CONFIG_SPL_BUILD)" to that #if statement because
the spin-table code can't currently work in SPL, and the spin-table file
isn't even compiled in SPL.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Move (and rename) the following CONFIG options to Kconfig:
CONFIG_DAVINCI_MMC (renamed to CONFIG_MMC_DAVINCI)
CONFIG_OMAP_HSMMC (renamed to CONFIG_MMC_OMAP_HS)
CONFIG_MXC_MMC (renamed to CONFIG_MMC_MXC)
CONFIG_MXS_MMC (renamed to CONFIG_MMC_MXS)
CONFIG_TEGRA_MMC (renamed to CONFIG_MMC_SDHCI_TEGRA)
CONFIG_SUNXI_MMC (renamed to CONFIG_MMC_SUNXI)
They are the same option names as used in Linux.
This commit was created as follows:
[1] Rename the options with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_DAVINCI_MMC/CONFIG_MMC_DAVINCI/g
s/CONFIG_OMAP_HSMMC/CONFIG_MMC_OMAP_HS/g
s/CONFIG_MXC_MMC/CONFIG_MMC_MXC/g
s/CONFIG_MXS_MMC/CONFIG_MMC_MXS/g
s/CONFIG_TEGRA_MMC/CONFIG_MMC_SDHCI_TEGRA/g
s/CONFIG_SUNXI_MMC/CONFIG_MMC_SUNXI/g
'
[2] Commit the changes
[3] Create entries in driver/mmc/Kconfig.
(copied from Linux)
[4] Move the options with the following command
tools/moveconfig.py -y -r HEAD \
MMC_DAVINCI MMC_OMAP_HS MMC_MXC MMC_MXS MMC_SDHCI_TEGRA MMC_SUNXI
[5] Sort and align drivers/mmc/Makefile for readability
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Xilinx ATF extending options for passing images from BL2(FSBL)
to BL31. U-Boot SPL is FSBL replacement that's why it should generate
handoff structure the same. Support only one entry which is U-Boot in
EL2 itself. When FIT image is adopted structure generate should be data
driven.
Currently ATF is placing this structure at the beggining of OCM which is
rewriting early parts of ATF which should be unused at that time.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add a string description for SYS_VENDOR to allow configuring boards from
other vendors than just "xilinx".
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use option NUM_DDR_CONTROLLERS in ddr Kconfig and clean up existing
usage in ls102xa and fsl-layerscape. Remove all powerpc macros in
config header and board header files.
Signed-off-by: York Sun <york.sun@nxp.com>
Create driver/ddr/fsl/Kconfig and move existing options. Clean up
existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s]
Signed-off-by: Tom Rini <trini@konsulko.com>
Instead of define CONFIG_SYS_FSL_SEC_COMPAT in header files for PowerPC
and ARM SoCs, move it to Kconfig under the driver.
Signed-off-by: York Sun <york.sun@nxp.com>
For prepending some board specific header area to U-Boot images we
were so far including a header file with a macro definition containing
the actual header specification.
This works fine if there are just a few statements and if there is only
one alternative.
However adding more complex code quickly gets messy with this approach,
so let's just drop that intermediate macro and let the #include actually
insert the code directly.
This converts the callers and the callees, but doesn't change anything
at this point.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The boot0 hook we have so far is applied _after_ the initial branch
to the "reset" entry point. An upcoming change requires even this
branch to be changed, so we apply the hook macro at the earliest
point, and have the branch in the hook file as well.
This is no functional change at this point, just refactoring to simplify
upcoming patches.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sunxi DRAM setup code needs an sdelay() implementation, which
wasn't defined for armv8 so far.
Shamelessly copy the armv7 version and adjust it to work in AArch64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
For boards that call s_init() when the SPL runs, we are expected to
setup an early stack before calling this C function.
Implement the proper AArch64 version of this based on the ARMv7 code.
This allows sunxi boards to setup the basic peripherals even with a
64-bit SPL.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Shuffle the macros around a little to remove the following warning
when building for i.MX28:
arch/arm/cpu/arm926ejs/mxs/spl_boot.c:44:26: warning: ‘iomux_boot’ defined but not used [-Wunused-const-variable=]
static const iomux_cfg_t iomux_boot[] = {
^~~~~~~~~~
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Use CONFIG_DM_ETH and remove board_eth_init code
from board files.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add CX9020 board based on mx53loco.
Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse
serial_mxc with DTE and prepare for device tree migration of other
functions and imx53 devices.
The CX9020 differs from i.MX53 Quick Start Board by:
- use uart2 instead of uart1
- DVI-D connector instead of VGA
- no audio
- CCAT FPGA connected to emi
- enable rtc
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
The LCDIF Pixel clock mux is not glitchless, so need
to gate before changing mux.
Also change enable_lcdif_clock prototype with a new input
parameter to indicate disable or enable.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The mux for the lcd clock is not glitchless,
so need to first gate the clock before changing the mux.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
>From RM, per_periph2_clk_sel option3 is:
"derive clock from 198MHz clock (divided 392MHz PLL2 PFD)."
So fix it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
liteBoard is a development board which uses liteSOM as its base.
Hardware specification:
* liteSOM (i.MX6UL, DRAM, eMMC)
* Ethernet PHY (id 0)
* USB host (usb_otg1)
* MicroSD slot (uSDHC1)
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
It's not necessary to define the processor in the defconfig file.
The preferred method to select the SoC is via Kconfig file.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This adds board support for the Toradex module family Colibri iMX6.
The familiy consists of a module with i.MX6 DualLite, i.MX6 Solo, both
with a version for commercial and industrial temperature range.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
This adds board support for the Toradex module family Apalis iMX6.
The familiy consists of a module with i.MX6 Dual, i.MX6 Quad with
commercial and industrial temperature range.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
A most basic PSCI implementation with only one psci_version is added for
LS1043A, this can verify the generic PSCI framework, and more platform specific
implementation will be added later.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Newly add ARMv8 PSCI needs to be initialized, be copied or reserved in right
place, this patch does all the setup steps.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch introduces a generic ARMv8 PSCI framework, with all functions
returning a dummy ARM_PSCI_RET_NI (Not Implemented), then it is up to each
platform to implement their own functions based on this framework.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds secure_text, secure_data and secure_stack sections for ARMv8 to
hold PSCI text and data, and it is based on the legacy implementation of ARMv7.
ARMV8_SECURE_BASE defines the address for PSCI secure sections, ARMV8_PSCI and
ARMV8_PSCI_NR_CPUS are firstly used in this patch, so they are introduce here
in Kconfig too.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
NXP/Freescale uses macro CONFIG_ARMV8_PSCI to enable their private PSCI
implementation in PPA firmware, but this macro naming too generic, so this
patch replaces it with a specic one CONFIG_FSL_PPA_ARMV8_PSCI.
And this macro CONFIG_ARMV8_PSCI will be used for a generic PSCI for ARMv8
which will be added in following patchs.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
solve issue when bootstage is used with armV7 generic timer
first call of timer_get_boot_us() use the function get_timer()
before timer initialization (arch.timer_rate_hz = 0)
=> div by 0
Commit-notes
When I activate bootstage on ARMV7 architecture with platform
using the generic armv7 timer defined in file
./arch/arm/cpu/armv7m/timer.c
I have a issue because gd->arch.timer_rate_hz = 0
For me the get_timer() function should not used before timer_init
(which initialize gd->arch.timer_rate_hz) at least for the ARMV7
timer.
But in the init sequence, the first bootstage fucntion is called
before timer_init and this function use the timer function.
For me it is a error in the generic init sequence :
mark_bootstage is called before timer_init.
static init_fnc_t init_sequence_f[] = {
....
arch_cpu_init_dm,
mark_bootstage, /* need timer, go after init dm */
...
#if defined(CONFIG_ARM) || defined(CONFIG_MIPS) || \
defined(CONFIG_BLACKFIN) || defined(CONFIG_NDS32) || \
defined(CONFIG_SPARC)
timer_init, /* initialize timer */
#endif
.......
To solve the issue for all the paltform, we can move timer_init()
call just before mark_bootstage() in this array...
It should be ok for ARMV7 but I don't sure for other platform
impacted
- the other ARM platform or ARMV7 wich don't use generic timer
- MIPS BLACKFIN NDS32 or SPARC
and I don't sure of impact for other function called
(board_early_init_f for example....)
=> This patch solve issue only in timer armv7
get_boot_us() can be called everytime without div by 0 issue
(gd->arch.timer_rate_hz is not used)
END
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
The default configuration for QSPI AHB bus can't support 16MB+.
But some flash on NXP layerscape board are more than 16MB.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
- add additional function erratum_a009942_check_cpo to check if the
board needs tuning CPO calibration for optimal setting.
- move ERRATUM_A009942(with revision to check cpo_sample option) from
fsl_ddr_gen4.c to ctrl_regs.c for reuse on all DDR4/DDR3 parts.
- move ERRATUM_A008378 from fsl_ddr_gen4.c to ctrl_regs.c
- remove obsolete ERRATUM_A004934 which is replaced with ERRATUM_A009942.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
[YS: Replaced CONFIG_QEMU_E500 with CONFIG_ARCH_QEMU_E500]
Reviewed-by: York Sun <york.sun@nxp.com>
Using alternative bootmode field to support automatic secondary boot
modes. It is purely software setting where SW modes are using free
bootmode combinations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP provides an option to overwrite bootmode setting which
can change SPL behavior.
For example: boot SPL via JTAG and then SPL loads images from SD.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch extends the imx6 clock code to enable or disable the EIM
slow clock, which in necessary when one wants to use EIM interface t
o read/write from external memory (e.g. NOR).
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
This patch adds initial support for Samtec VIN|ING 2000 board.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
UDOO Neo Board is a development board from Seco that has three models:
- UDOO Neo Basic
- UDOO Neo Basic Kick Starter
- UDOO Neo Extended
- UDOO Neo Full
All versions are based on the i.MX6 SoloX processor.
For more details about the UDOO Neo board, please refer to:
http://www.udoo.org/udoo-neo/
This work is based on a previous commit of Francesco Montefoschi
<francesco.monte@gmail.com>:
877b71184a
Only tested on the UDOO Neo Full board.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The DDR calibration routines are gated by conditionals for the
i.MX6DQ SOCs, but with the use of the sysinfo parameter, these
are usable on at least i.MX6SDL and i.MX6SL variants with DDR3.
Also, since only the Novena board currently uses the dynamic
DDR calibration routines, these routines waste space on other
boards using SPL.
Add a KConfig entry to allow boards to selectively include the
DDR calibration routines.
Signed-off-by: Eric Nelson <eric@nelint.com>
Add routine mmdc_read_calibration() to return the output of DDR
calibration. This can be used for debugging or to aid in construction
of static memory configuration.
This routine will be used in a subsequent patch set adding a virtual
"mx6memcal" board, but could also be useful when gathering statistics
during an initial production run.
Signed-off-by: Eric Nelson <eric@nelint.com>
The DDR calibration routines have scattered support for bus
widths other than 64-bits:
-- The mmdc_do_write_level_calibration() routine assumes the
presence of PHY1, and
-- The mmdc_do_dqs_calibration() routine tries to determine
whether one or two DDR PHYs are active by reading MDCTL.
Since a caller of these routines must have a valid struct mx6_ddr_sysinfo
for use in calling mx6_dram_cfg(), and the bus width is available in the
"dsize" field, use this structure to inform the calibration routines which
PHYs are active.
This allows the use of the DDR calibration routines on CPU variants
like i.MX6SL that only have a single MMDC port.
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The DDR calibration code is only setting flag DG_CMP_CYC (DQS gating sample
cycle) for the first PHY.
Set the 32-cycle flag for both PHYs and clear when done so the MPDGCTRL0
output value isn't polluted with calibration artifacts.
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Before disable cache, need to first flush cache.
There maybe dirty data in D-Cache before disable D-Cache.
After disable D-Cache, the first store instructions in
psci_v7_flush_dcache_all will directly store registers
{r4-r5, r7, r9-r11, lr} to memory.
If there is dirty data before disable D-Cache,
psci_v7_flush_dcache_all will flush data to memory,
and may overwrite the memory that hold the registers
{r4-r5, r7, r9-r11, lr}.
So before disable cache, first flush D-Cache.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Hongbo Zhang <hongbo.zhang@nxp.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Tom Rini <trini@konsulko.com>
As PSCI and secure monitor firmware framework are enabled, this patch is
to support loading 32-bit OS in such case. The default target exception
level returned to U-Boot is EL2, so the corresponding work to switch to
AArch32 EL2 and jump to 32-bit OS are done in U-Boot and secure firmware
together.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Spin-table method is used for secondary cores to load 32-bit OS. The
architecture information will be got through checking FIT image and
saved in the os_arch element of spin-table, then the secondary cores
will check os_arch and jump to 32-bit OS or 64-bit OS automatically.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
To support loading a 32-bit OS, the execution state will change from
AArch64 to AArch32 when jumping to kernel.
The architecture information will be got through checking FIT image,
then U-Boot will load 32-bit OS or 64-bit OS automatically.
Signed-off-by: Ebony Zhu <ebony.zhu@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
NXP ARMv8 SoC LS2080A release all secondary cores in one-go.
But other new SoCs like LS2088A, LS1088A release secondary
cores one by one.
Update code to release secondary cores based on SoC SVR
Add code to release cores one by one for non LS2080A SoCs
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: remove "inline" from declaration of initiator_type]
Reviewed-by: York Sun <york.sun@nxp.com>
The QorIQ LS2088A SoC is built on layerscape architecture.
It is similar to LS2080A SoC with some differences like
1)Timer controller offset is different
2)It has A72 cores
3)It supports TZASC module
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2080 SoC and its personalities does not support TZASC
But other new SoCs like LS2088A, LS1088A supports TZASC
Hence, skip initializing TZASC for Ls2080A based on SVR
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TZASC registers like TZASC_GATE_KEEPER, TZASC_REGION_ATTRIBUTES
are 32-bit regsiters.
So while doing register load-store operations, 32-bit intermediate
register, w0 should be used.
Update x0 register to w0 register type.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Timer controller base address has been changed from
LS2080A SoC (and its personalities) to new SoCs like
LS2088A, LS1088A.
Use SVR based timer base address detection to avoid compile time #ifdef.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Implement a hook to allow boards to save boot-time CPU state for later
use. When U-Boot is chain-loaded by another bootloader, CPU registers may
contain useful information such as system configuration information. This
feature mirrors the equivalent ARMv7 feature.
Signed-off-by: Cédric Schieli <cschieli@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
This moves what was in arch/arm/cpu/armv7/omap-common in to
arch/arm/mach-omap2 and moves
arch/arm/cpu/armv7/{am33xx,omap3,omap4,omap5} in to arch/arm/mach-omap2
as subdirectories. All refernces to the former locations are updated to
the current locations. For the logic to decide what our outputs are,
consolidate the tests into a single config.mk rather than including 4.
Signed-off-by: Tom Rini <trini@konsulko.com>
Detect the board very early and avoid reading eeprom multiple times.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is similar to Commit 93e6253d11 ("ARM: OMAP4/5: Centralize
early clock initialization") that was done for OMAP4+, reflecting the same
for AM33xx and AM43xx SoCs to centralize clock initialization.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add setup_early_clocks that calls setup_clocks_for_console for
ti81xx]
Signed-off-by: Tom Rini <trini@konsulko.com>
Update CONFIG_LS2080A to CONFIG_FSL_LSCH3 to make those workaround
implementing of erratum reusable for more SoCs.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Early system initialization is being done before initf_dm is being called
in U-Boot. Then system will fail to boot if any of the DM enabled driver
is being called in this system initialization code. So, rearrange the
code a bit so that DM enabled drivers can be called during early system
initialization. This is inspired by commit e850ed82bc ("ARM: OMAP4+: Allow
arch specific code to use early DM")
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Highlights this time around:
- x86 efi_loader support
- hello world efi test case
- network device name is now representative
- terminal output reports modes correctly
- fix psci reset for ls1043/ls1046
- fix efi_add_runtime_mmio definition for x86
- efi_loader support for ls2080
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=xmR3
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2016-11-17
Highlights this time around:
- x86 efi_loader support
- hello world efi test case
- network device name is now representative
- terminal output reports modes correctly
- fix psci reset for ls1043/ls1046
- fix efi_add_runtime_mmio definition for x86
- efi_loader support for ls2080
When implementing efi loader support, we can expose runtime services
for payloads. One such service is CPU reset.
This patch implements RTS CPU reset support for layerscape systems.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
The efi loader code has its own memory map, so it needs to be aware where
the spin tables are located, to ensure that no code writes into those
regions.
Signed-off-by: Alexander Graf <agraf@suse.de>
The NXP ls1043 and ls1046 systems do not (yet) have PSCI enablement
for reset. Don't enable generic PSCI reset code on them.
Signed-off-by: Alexander Graf <agraf@suse.de>
According to design team, we need to set REFTOP_VBGADJ
in PMU MISC0 according to the REFTOP_TRIM[2:0] fuse. the
actually table is as below:
'000" - set REFTOP_VBGADJ[2:0] to 3'b000
'001" - set REFTOP_VBGADJ[2:0] to 3'b001
'010" - set REFTOP_VBGADJ[2:0] to 3'b010
'011" - set REFTOP_VBGADJ[2:0] to 3'b011
'100" - set REFTOP_VBGADJ[2:0] to 3'b100
'101" - set REFTOP_VBGADJ[2:0] to 3'b101
'110" - set REFTOP_VBGADJ[2:0] to 3'b110
'111" - set REFTOP_VBGADJ[2:0] to 3'b111
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Need to gate ENET clock when switching to a new clock parent, because
the mux is not glitchless.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye.Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Do not setup use_alt bit which copy alternative boot mode to
boot mode. The reason is that this bit is cleared after POR
but not after any software reset which will cause
that after SW reset bootrom will look for different boot image.
This patch setups alternative boot mode selection (purely SW
handling) and extends code to read this alternative boot mode first and
use it if it is setup.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Zynq/ZynqMP boot.bin file contains a region for register initialization
data. Filling in proper values in this table can reduce boot time
(e.g. about 50ms faster on QSPI boot) and also reduce the size of
the SPL binary.
The table is a simple text file with register+data on each line. Other
lines are simply skipped. The file can be passed to mkimage using the
"-R" parameter.
It is recommended to add reg init file to board folder.
For example:
CONFIG_BOOT_INIT_FILE="board/xilinx/zynqmp/xilinx_zynqmp_zcu102/reg.int
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for EFI apps on aarch64. This includes start-up and relocation
code plus a link script.
Signed-off-by: Simon Glass <sjg@chromium.org>
[agraf: add kconfig dep]
Signed-off-by: Alexander Graf <agraf@suse.de>
SoC-specific logic may be required for all forms of cache-wide
operations; invalidate and flush of both dcache and icache (note that
only 3 of the 4 possible combinations make sense, since the icache never
contains dirty lines). This patch adds an optional hook for all
implemented cache-wide operations, and renames the one existing hook to
better represent exactly which operation it is implementing. A dummy
no-op implementation of each hook is provided.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
For 64-bit ARM systems we provide just a timer_read_counter()
implementation and rely on the generic non-uclass get_ticks() function
in lib/time.c to call the former.
However this function is actually not 64-bit safe, as it assumes a
"long" to be 32-bit. Beside the fact that the resulting uint64_t
isn't bigger than "long" on 64-bit architectures and thus combining two
counters makes no sense, we get all kind of weird results when we try
to OR in the high value shifted by _32_ bits.
So let's avoid that function at all and provide a straight forward
get_ticks() implementation for ARMv8, which also is in line with ARMv7.
This fixes occasional immediate time-out expiration issues I see on the
Pine64 board. The root cause of this needs to be investigated, but this
fix looks like the right thing anyway.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
CONFIG_SUNXI -> CONFIG_ARCH_SUNXI
and removed CONFIG_SUNIX from config_whitelist.txt
Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>