MV_DDR_FREQ_SAR lets the DDR frequency be determined by hardware
strapping. This also has the side effect of running the DDR clock in
synchronous mode with the CPU core clock rather than from an independent
PLL. We've seen this improve reliability in operation across a number of
boards and temperature ranges.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Commit dc146ca111 ("Kconfig: Migrate CONFIG_BUILD_TARGET") made the
mvebu default build target depend on CONFIG_SPL_BUILD. Unfortunately,
there is no such Kconfig symbol. Use the CONFIG_SPL symbol instead to
fix that.
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The dm_gpio_set_value() routine sets signal logical level, with
GPIO_ACTIVE_LOW/HIGH value taken into account. Reset active value is 1
(asserted), while reset inactive value is 0 (de-asserted). Fix the reset
toggle code to set the correct reset logic value.
Reported-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The PCIe slot PERST signal is active low. Fix the gpio signal
description in the dts.
This happened to work because the pcie_dw_mvebu driver sets the reset
gpio level to 1 (high) to release the reset. The following commit will
fix that.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
For !DM case busses are listed as
ZynqMP> i2c bus
Bus 0: zynq_0
Bus 1: zynq_0->PCA9544A@0x75:0
Bus 2: zynq_0->PCA9544A@0x75:1
Bus 3: zynq_0->PCA9544A@0x75:2
Bus 4: zynq_1
Bus 5: zynq_1->PCA9548@0x74:0
Bus 6: zynq_1->PCA9548@0x74:1
Bus 7: zynq_1->PCA9548@0x74:2
Bus 8: zynq_1->PCA9548@0x74:3
Bus 9: zynq_1->PCA9548@0x74:4
Bus 10: zynq_1->PCA9548@0x75:0
Bus 11: zynq_1->PCA9548@0x75:1
Bus 12: zynq_1->PCA9548@0x75:2
Bus 13: zynq_1->PCA9548@0x75:3
Bus 14: zynq_1->PCA9548@0x75:4
Bus 15: zynq_1->PCA9548@0x75:5
Bus 16: zynq_1->PCA9548@0x75:6
Bus 17: zynq_1->PCA9548@0x75:7
where is exactly describing i2c bus topology.
By moving to DM case i2c mux buses are using names from DT and because
i2c-muxes describing sub busses with the same names like i2c@0, etc it
is hard to identify which bus is where.
Linux is adding topology information to i2c-mux busses to identify them
better.
This patch is doing the same and composing bus name with topology
information.
When patch is applied with topology information on zcu102-revA.
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 2: i2c@ff020000->i2c-mux@75->i2c@0
Bus 3: i2c@ff020000->i2c-mux@75->i2c@1
Bus 4: i2c@ff020000->i2c-mux@75->i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 5: i2c@ff030000->i2c-mux@74->i2c@0 (active 5)
54: eeprom@54, offset len 1, flags 0
Bus 6: i2c@ff030000->i2c-mux@74->i2c@1
Bus 7: i2c@ff030000->i2c-mux@74->i2c@2
Bus 8: i2c@ff030000->i2c-mux@74->i2c@3
Bus 9: i2c@ff030000->i2c-mux@74->i2c@4
Bus 10: i2c@ff030000->i2c-mux@75->i2c@0
Bus 11: i2c@ff030000->i2c-mux@75->i2c@1
Bus 12: i2c@ff030000->i2c-mux@75->i2c@2
Bus 13: i2c@ff030000->i2c-mux@75->i2c@3
Bus 14: i2c@ff030000->i2c-mux@75->i2c@4
Bus 15: i2c@ff030000->i2c-mux@75->i2c@5
Bus 16: i2c@ff030000->i2c-mux@75->i2c@6
Bus 17: i2c@ff030000->i2c-mux@75->i2c@7
Behavior before the patch is applied.
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 2: i2c@0
Bus 3: i2c@1
Bus 4: i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 5: i2c@0 (active 5)
54: eeprom@54, offset len 1, flags 0
Bus 6: i2c@1
Bus 7: i2c@2
Bus 8: i2c@3
Bus 9: i2c@4
Bus 10: i2c@0
Bus 11: i2c@1
Bus 12: i2c@2
Bus 13: i2c@3
Bus 14: i2c@4
Bus 15: i2c@5
Bus 16: i2c@6
Bus 17: i2c@7
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
For i2c controllers which are missing alias in DT there is no req_seq
setup. This function is setting up proper ID based on highest found
alias ID.
On zcu102 this is the behavior when patch is applied.
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 2: i2c@0
Bus 3: i2c@1
Bus 4: i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 5: i2c@0 (active 5)
54: eeprom@54, offset len 1, flags 0
Bus 6: i2c@1
Bus 7: i2c@2
Bus 8: i2c@3
Bus 9: i2c@4
Bus 10: i2c@0
Bus 11: i2c@1
Bus 12: i2c@2
Bus 13: i2c@3
Bus 14: i2c@4
Bus 15: i2c@5
Bus 16: i2c@6
Bus 17: i2c@7
Before this patch applied (controllers have -1 ID)
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus -1: i2c@0
Bus -1: i2c@1
Bus -1: i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus -1: i2c@0 (active 0)
54: eeprom@54, offset len 1, flags 0
Bus -1: i2c@1
Bus -1: i2c@2
Bus -1: i2c@3
Bus -1: i2c@4
Bus -1: i2c@0
Bus -1: i2c@1
Bus -1: i2c@2
Bus -1: i2c@3
Bus -1: i2c@4
Bus -1: i2c@5
Bus -1: i2c@6
Bus -1: i2c@7
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
There is a need to find out the first free i2c ID which can be used for
i2s buses (including i2c buses connected to i2c mux). Do it early in
init and share this variable with other i2c classes for uniq bus
identification.
add from hs:
fix build problem in i2c-uclass.c for omap devices
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Common sound support
buildman environment support
of-platdata documentation improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlxf7igRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYKfggApQiL0Gv6NdGAQN+zfpjKY5a2QyjKsAxa
KLm3q8XyXIQXufMWOEPoW1iWm0iixpIFgChy8ff3m/OPDzsx99UXDTyvjitsSxtQ
5tFu8K78nUZT6OOE3HNhhlyW/xK442oKBzGt4MUt3kUZOELsCNuftgbJUWksHuO3
6pPrgt36E0uRGbUA4ioYCU336viJRPOOCdqb8hHViEihFj/IEv5T82RdE5y97YxG
dT7BZxjPkBH5ZN1uD/tdxG1k6IZBagZiYoDAsYp4YqNwmVsm5sLrZ9QVSf7EcH/y
qX8butZesiMd7xm7RROlrIImh7fb36N3zsoRiUWZDo1Al3IRkmZyVA==
=tdut
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-10feb19' of git://git.denx.de/u-boot-dm
Samsung sound patches (applied for Samsung maintainer)
Common sound support
buildman environment support
of-platdata documentation improvements
- bcm6345 watchdog, bcm63158/bcm963158 initial support.
- Various TI platform resyncs and improvements.
- FDT support in Android-format images.
- stm32mp1 improvements.
At present there is still some samsung-specific code in the audio codecs.
Remove it so that these can be used by other SoCs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow misc devices to have children, so that we can use this uclass for
cases where a child device (e.g. I2S) needs to access a misc driver for
transferring data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix a typo in the error message from CheckOutputDir().
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Improve some things in the documentation of OF_PLATDATA that I found
while porting socfgpa_gen5 to it.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sometimes it is useful to see the environment that was used to build
U-Boot. Write this out to a file in the build directory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use regulator_set_enable_if_allowed() api instead of regulator_set_enable()
while enabling io regulators. This way the driver doesn't see an error
when disabling an always-on regulator and when enabling is not supported.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
regulator_set_enable() api throws an error in the following three cases:
- when requested to disable an always-on regulator
- when set_enable() ops not provided by regulator driver
- when enabling is actually failed.(Error returned by the regulator driver)
Sometimes consumer drivers doesn't want to track the first two scenarios
and just need to worry about the case where enabling is actually failed.
But it is also a good practice to have an error value returned in the
first two cases.
So introduce an api regulator_set_enable_if_allowed() which ignores the
first two error cases and returns an error as given by regulator driver.
Consumer drivers can use this api need not worry about the first two
error conditions.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts commit e17e0ceb83.
It is advised to return an error when trying to disable an always-on
regulator and let the consumer driver handle the error if needed.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This enum still exists but we can shrink it a little based on recent
driver-model conversions with samsung. Update it to remove unused items.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Now that these boards use driver model we can drop the old code. At
present s5p_mmc_init() is still used by goni and smdkv310 so cannot be
removed unless we remove those boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
This function is not needed now since the audio codecs have been converted
to proper drivers. The codec-enable GPIO is handled there.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Update the flashmap so that this board can be started over USB A-A. It
is slightly different from snow.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Update the spring settings to use this codec, which is what it actually
shipped with.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Move all exynos boards over to use CONFIG_BLK.
This converts s5p_goni also, but adding dummy functions for pinmux and
peripheral ID. This will not function correctly, but gives the maintainer
more time to convert the board if desired.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
At present the model is shown twice, once in the generic code and once
in the exynos code. Drop the latter.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
This converts the following to Kconfig:
CONFIG_BOARD_TYPES
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Perform some cosmetic cleanup of the ATF image startup function, namely
fixing a spelling mistake, capitalization of a few words, spacing, as
well aligning how errors are printed and as using panic() for cases that
were using a combination of printf() + hang().
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The first element in the debug section is expected to be debugUID.
ROM will not parse this correctly when out of order, fix this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Bootm will fail to load kernels over 8MB, this is not enough
for our 64bit kernel images. Increase this to 64MB.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The second loader stages may be stored on GPT partitions,
enable support for this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Calling sata_scan() with a null pointer probably won't make much sense.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
While uclass_find_device() fails with -ENODEV in case of list_empty
strangely uclass_find_first_device() returns 0.
Fix uclass_find_first_device() to also fail with -ENODEV instead.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This add the initial support of the broadcom reference
board bcm963158 with a bcm63158 SoC.
This board has 1 GB of ram, 512 MB of flash (nand),
2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This add the initial support of the broadcom bcm63158 SoC family,
only the cpu, dram and uart are supported.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
The board_r init function was complaining that we are looping through
an array, calling all our tiny init stubs sequentially via indirect
function calls (which can't be speculated, so they are slow).
The solution to that is pretty easy though. All we need to do is inline
the function that loops through the functions and the compiler will
automatically convert almost all indirect calls into direct inlined code.
With this patch, the overall code size drops (by 40 bytes on riscv64)
and boot time should become measurably faster for every target.
Signed-off-by: Alexander Graf <agraf@suse.de>
The TPS62517 PMIC driver has been partially converted to DM, so the
legacy I2C access layer isn't needed anymore.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Errata i929 in certain OMAP5/DRA7XX/AM57XX silicon revisions
(SPRZ426D - November 2014 - Revised February 2018 [1]) mentions
unexpected tuning pattern errors. A small failure band may be present
in the tuning range which may be missed by the current algorithm.
Furthermore, the failure bands vary with temperature leading to
different optimum tuning values for different temperatures.
As suggested in the related Application Report (SPRACA9B - October 2017
- Revised July 2018 [2]), tuning should be done in two stages.
In stage 1, assign the optimum ratio in the maximum pass window for the
current temperature. In stage 2, if the chosen value is close to the
small failure band, move away from it in the appropriate direction.
References:
[1] http://www.ti.com/lit/pdf/sprz426
[2] http://www.ti.com/lit/pdf/SPRACA9
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
To activate the csg option, the driver need to set the bit2
of PLLNCR register = SSCG_CTRL: Spread Spectrum Clock Generator
of PLLn enable.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- Add st,digbypass on clk_hse node (needed for board rev.C)
- MLAHB/AHB max frequency increased from 200 to 209MHz, with:
- PLL3P set to 208.8MHz for MCU sub-system
- PLL3Q set to 24.57MHz for 48kHz SAI/SPI2S
- PLL3R set to 11.29MHz for 44.1kHz SAI/SPI2S
- PLL4P set to 99MHz for SDMMC and SPDIFRX
- PLL4Q set to 74.25MHz for EVAL board
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>