K3 J721E:
* DMA support.
* MMC and ADMA support.
* EEPROM support.
* J721e High Security EVM support.
* USB DT nodes
K3 AM654:
* Fixed boot due to pmic probe error.
* USB support and DT nodes.
* ADMA support
DRA7xx/AM57xx:
* BBAI board support
* Clean up of net platform code under board/ti
AM33/AM43/Davinci:
* Reduce SPL size for omap3 boards.
* SPL DT support for da850-lcdk
* PLL divider fix for AM335x
Functions fracpll_configure(), decode_intpll(), decode_fracpll(),
get_root_src_clk() and get_root_clk() are used only in the scope of this
file, so make them static to fix the following sparse warnings:
arch/arm/mach-imx/imx8m/clock_imx8mm.c:50:5: warning: no previous
prototype for ‘fracpll_configure’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:271:5: warning: no previous
prototype for ‘decode_intpll’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:418:5: warning: no previous
prototype for ‘decode_fracpll’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:483:5: warning: no previous
prototype for ‘get_root_src_clk’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:527:5: warning: no previous
prototype for ‘get_root_clk’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
The mux mode is embedded in the PAD definition and therefore there is
no need to repeat it in the PAD configuration value (more over since
this information will be masked out when the configuration value is
applied).
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
On SPL enabled systems, the current s_init code (wdog, clock and ldo
init) is executed twice (by SPL and u-boot). This is not necessary and
might lead to boot issues (ie, starting PMC1 when it is already running).
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add iMX6ULL VisionSOM SoM and VisionCB-RT-STD evaluation board support.
The SoM has an iMX6ULL, 512 MiB of DRAM and microSD slot. The carrier
board has Ethernet, USB host port, USB OTG port.
Signed-off-by: Arkadiusz Karas <arkadiusz.karas@somlabs.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add pinmux for USB1 and enable it as a peripheral port in U-Boot
specific dtsi since U-Boot does not support OTG.
Disable USB0 as its not available on the baseboard.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for USB0 and USB1 instances on the AM6 SoC.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
None of these boards boot, but the solution appears to be the same.
All the boards have SPL that is too large. With a few defconfig
options removed, these corresponding options can be removed from
their respective SPL dtb files.
This patch unifies the DM37/OMAP35 boards' -u-boot.dtsi files
to remove gpio's, i2c, bandgap, thermal zones, unneeded uarts, and
unneeded MMC nodes.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The memory allocated to store the FIT image containing SYSFW and board
configuration data is statically defined to the largest size expected.
This was 276000 bytes but now needs to be grown to 277000 to make room
for the slightly larger SYSFW image used on J721e High-Security devices.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
ROM configures certain firewalls based on its usage, which includes
the one in front of boot peripherals. In specific case of boot
peripherals, ROM does not open up the full address space corresponding
to the peripherals. Like in OSPI, ROM only configures the firewall region
for 32 bit address space and mark 64bit address space flash regions
as in-accessible.
When security-cfg is initialized by sysfw, all the non-configured
firewalls are kept in bypass state using a global setting. Since ROM
configured firewalls for certain peripherals, these will not be touched.
So when bootloader touches any of the address space that ROM marked as
in-accessible, system raises a firewall exception causing boot hang.
It would have been ideal if sysfw cleans up the ROM configured boot
peripheral firewalls. Given the memory overhead to store this
information provided by ROM and the boot time increase in re configuring
the firewalls, it is concluded to clean this up in bootloaders.
So disable all the firewalls that ROM doesn't open up the full address
space.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Venkateswara Rao Mandela <venkat.mandela@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This file used to be the common location for K3 init when AM6 was the
only device, but common code was moved to common.c and this file became
AM6 specific, correct this header text.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
wkup_vtm populates only 1 power-domain cell in it's node. But the
power-domain cell are defined as 2. Due to this the following warning
comes during build:
arch/arm/dts/k3-am654-r5-base-board.dtb: Warning (power_domains_property):
/interconnect@100000/interconnect@28380000/interconnect@42040000/
wkup_vtm@42050000:power-domains: property size (8) too small for cell size 2
Fix this by updating the power-domain cells.
Fixes: cfa6bd549c ("arm: dts: k3-am654-r5-base-board: Add VTM node")
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
On K3 systems U-Boot runs on both an R5 and a large ARM cores (usually
A53 or A72). The large ARMs are coherent with the DMA controllers and
the SYSFW that perform authentication. And previously the R5 core did
not enable caches. Now that R5 does enable caching we need to be sure
to clean out any of the image that may still only be in cache before we
read it using external DMA for authentication.
Although not expected to happen, it may be possible that the data was
read back into cache after the flush but before the external operation,
in this case we must invalidate our stale local cached version.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Not finding a node that we try to disable does not always need to be
fatal to boot but should at least print out a warning. Return error
from fdt_disable_node as it did fail to disable the node, but only
warn in the case of disabling the TRNG as this will not prevent boot.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Make the wkup_i2c0 module usable across all stages of U-Boot by adding
the needed definitions including the associated pinmux definitions.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The TI J721E EVM system on module (SOM), the common processor board, and
the associated daughtercards have on-board I2C-based EEPROMs containing
board config data. Use the board detection infrastructure to do the
following:
1) Parse the J721E SOM EEPROM and populate items like board name, board
HW and SW revision as well as board serial number into the TI common
EEPROM data structure residing in SRAM scratch space
2) Check for presence of daughter card(s) by probing associated I2C
addresses used for on-board EEPROMs containing daughter card-specific
data. If such a card is found, parse the EEPROM data such as for
additional Ethernet MAC addresses and populate those into U-Boot
accordingly
3) Dynamically apply daughter card DTB overlays to the U-Boot (proper)
DTB during SPL execution
4) Dynamically create an U-Boot ENV variable called name_overlays
during U-Boot execution containing a list of daugherboard-specific
DTB overlays based on daughercards found to be used during Kernel
boot.
This patch adds support for the J721E system on module boards containing
the actual SoC ("J721EX-PM2-SOM", accessed via CONFIG_EEPROM_CHIP_ADDRESS),
the common processor board ("J7X-BASE-CPB"), the Quad-Port Ethernet
Expansion Board ("J7X-VSC8514-ETH"), the infotainment board
("J7X-INFOTAN-EXP") as well as for the gateway/Ethernet switch/industrial
expansion board ("J7X-GESI-EXP").
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
BeagleBoard.org BeagleBone AI is an open source hardware single board
computer based on the Texas Instruments AM5729 SoC featuring dual-core
1.5GHz Arm Cortex-A15 processor, dual-core C66 digital signal
processor (DSP), quad-core embedded vision engine (EVE), Arm Cortex-M4
processors, dual programmable realtime unit industrial control
subsystems and more. The board features 1GB DDR3L, USB3.0 Type-C, USB
HS Type-A, microHDMI, 16GB eMMC flash, 1G Ethernet, 802.11ac 2/5GHz,
Bluetooth, and BeagleBone expansion headers.
For more information, refer to:
https://beaglebone.ai
The corresponding patch against the mainline linux kernel can be found
at: https://patchwork.kernel.org/patch/11254903/
This patch introduces the BeagleBone AI device tree.
Note that the device use the "ti,tpd12s016" component which is software
compatible with "ti,tpd12s015". Thus we only use the latter driver.
Signed-off-by: Jason Kridner <jdk@ti.com>
Signed-off-by: Caleb Robey <c-robey@ti.com>
Cc: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
These are necessities for beaglebone ai boot. There is the addition of
CONFIG_SUPPORT_EMMC_CONFIG to the Kconfig file. This is present upstream
but not in 19.01 yet.
Signed-off-by: Jason Kridner <jdk@ti.com>
Signed-off-by: Caleb Robey <c-robey@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Get clk_xin by name instead of by index to avoid having to put clocks in
the same order in all devices.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Currently, the da850-lcdk uses SPL_OF_PLATDATA and manually loads
the necessary source code instead of using the auto-generated,
because the drivers don't properly autogenerate the code.
This patch simply enables the various device tree options to
mimic the da850-evm which doesn't need or use OF_PLATDATA for
device tree support. It does not disable OF_PLATDATA.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
J721e has two instances of Cadence USB3 controller. Add DT nodes for the
same. USB0 is configured to device mode and USB1 is configured to host
mode. For now only high speed mode is supported.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
This function related to timer and most of the timer functions are in
time.h, so move this function there.
Signed-off-by: Simon Glass <sjg@chromium.org>
These three clock functions don't use driver model and should be migrated.
In the meantime, create a new file to hold them.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is only used on ARM devices so does not belong in the global
common header file. Move it to an ARM header.
Signed-off-by: Simon Glass <sjg@chromium.org>
These functions relate to setting up the device tree for booting the OS.
The fdt_support.h header file supports similar functions, so move these
there.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is an init function so move it out of the common header. Avoid using
the typedef so that we don't have to include the global_data header file.
Also tidy up the function style in comments while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add missing 'eth-ck' clock to the ethernet node. These clock are used to
generate external clock signal for the PHY in case 'st,eth_ref_clk_sel'
is specified.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Until now, we only support aes128. This commit add the support
of aes192 and aes256.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Split the board and SOC support for STM32MP15x family and
prepare the introduction of new boards with STM32MP15x.
This path define the 2 configurations:
- STM32MP15x: STM32MP15x soc support (new)
- TARGET_ST_STM32MP15x: STMicroelectronics board support (choice)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Let board code override setup_mac_address(), which is useful e.g. if the
board derives the MAC address from another source, like an I2C EEPROM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The main prompt for this (defined in /Kconfig) is visible at all times,
which means there's no reason to have an additional, machine-specific
prompt to set the same option.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
SoC base addresses should better go into a common SoC file instead
of repeating the definition in each board file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This patch move u-boot properties to -u-boot.dtsi file.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
This adds a general board file based on MT7622 SoCs from MediaTek.
This commit is adding the basic boot support for the MT7622 rfb.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
