Commit Graph

14034 Commits

Author SHA1 Message Date
Niel Fourie
37bfd9cb50 PowerPC: keymile: Add support for kmcent2 board
Add basic support for the Hitachi Power Grids kmcent2 board, based
on the NXP QorIQ T1040 SoC.

Signed-off-by: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
[Fixed blank line at EOF errors]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-08 14:01:18 +05:30
Niel Fourie
df86d324c7 keymile: common: update to set_env_hex(), fix "pram" radix
Replace instances of sprintf()/set_env() for setting hexadecimal
values with set_env_hex().

In set_km_env() the "pram" variable was set to an hexadecimal
value, while initr_mem() expects an unsigned decimal, so use
set_env_ulong() instead.

Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-08 14:01:17 +05:30
Aleksandar Gerasimovski
e081d9441e board/km/common: fix pnvramaddr and varaddr
Take into account SDRAM_BASE address when calculating pnvramaddr and
varaddr offsets.
Up to now Keymile designs had SDRAM_BASE equal to zero and the offsets
where calculated correctly, this fix is for the upcoming designs that
have SDRAM_BASE different then zero.

Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-08 14:01:17 +05:30
Aleksandar Gerasimovski
d141f4b298 keymile: common: qrio: print QRIO id and revision number
Add show_qrio function to print chip id and revision information.
There are already multiple QRIO chip versions available and the upcoming
designs may want to show used version.

Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-08 14:01:17 +05:30
Aleksandar Gerasimovski
b99cc27111 board: keymile: common: fix qrio compilation for arm
This patch is fixing qrio driver compilation for ARM architecture:
- It includes asm/io.h for in_/out_ access
- It use correct names for set/clear_bits as defined in linux/bitops.h

Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-08 14:01:16 +05:30
Michael Walle
805b2423b4 board: sl28: add SATA support
Enable SATA support. Although not supported by the usual SATA pins on
the SMARC baseboard connector, SATA mode is supported on a PCIe lane.
This way one can use a mSATA card in a Mini PCI slot.

We need to invert the received data because in this mode the polarity of
the SerDes lane is swapped. Provide a fixup in board_early_init_f() for
the SPL. board_early_init_f() is then not common between SPL and u-boot
proper anymore, thus common.c is removed, as it just contained said
function.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-08 14:01:16 +05:30
Michael Walle
b463010be0 board: sl28: add network variant 2 support
Although this variant has two external network ports, they are not (yet)
supported by the bootloader because they are connected via an internal
network switch. Otherwise its the same as the other variants.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-08 14:01:16 +05:30
Michael Walle
4029d356e6 board: sl28: add network variant 1 support
This variant has one network port connected via RGMII and doesn't have
any TSN capabilities out-of-the-box. Instead it has all four SerDes
lanes available for customer use.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-08 14:01:15 +05:30
Stefan Roese
61b70422c3 arm: mvebu: theadorable: Set deephasis bit in PCIe configs very early
Testing has shown, that the quality of the PCIe signals and also the
stability of correct link establishment on the 2 PCIe ports is better,
when the deemphasis bit is set in the PCIe config register.

This needs to be done very early, even before the SERDES setup code is
run. This way, the first link will already be established with this
setup.

Signed-off-by: Stefan Roese <sr@denx.de>
2021-02-08 08:53:14 +01:00
Stefan Roese
54504de24d arm: mvebu: theadorable: Enhance "pcie" test cmd to check link width/speed
This patch changes the board specific "pcie" U-Boot command to not only
check for PCIe device existance but also for the correct link speed
and width that has been established. This cmd can be used by U-Boot
scripts for automated testing, if the PCIe setup is correct. Meaning,
that all PCIe devices are correctly detected and the link speed and
width is corrent.

Signed-off-by: Stefan Roese <sr@denx.de>
2021-02-08 08:53:14 +01:00
Pali Rohár
44be835d25 arm: mvebu: Espressobin: Set default value for $ethNaddr env variable
On Espressobin board are MAC addresses stored in U-Boot env area. Therefore
they are not present in default_environment[] array constructed at compile
time.

This change puts permanent MAC addresses into default_environment[] array
at board runtime. Espressobin board has enabled DEFAULT_ENV_IS_RW option
and therefore can modify this array.

This change ensure that 'env default -a' does not delete permanent MAC
addresses from Espressobin env storage area.

Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Andre Heider <a.heider@gmail.com>
2021-02-08 08:53:08 +01:00
Pali Rohár
c4df0f6f31 arm: mvebu: Espressobin: Set default value for $fdtfile env variable
On Espressobin board value for $fdtfile cannot be determined at compile
time and is calculated at board runtime code. This change uses a new option
DEFAULT_ENV_IS_RW to allow modifying default_environment[] array at runtime
and set into it correct value.

This change also ensure that 'env default -a' set correct value to $fdtfile.

Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Andre Heider <a.heider@gmail.com>
2021-02-08 08:53:08 +01:00
Adam Ford
0099dfd5e5 ARM: rmobile: Add Beacon EmbeddedWorks RZG2H Dev Kit
The Beacon EmbeddedWorks kit is based on the R8A774E1 SoC also
known as the RZ/G2H.

The kit consists of a SOM + Baseboard and supports microSD,
eMMC, Ethernet, a couple celular radios, two CAN interfaces,
Bluetooth and WiFi.  It shares much of the same design as
the RZ/G2M and RZ/G2N dev kits.

Signed-off-by: Adam Ford <aford173@gmail.com>
2021-02-07 21:12:57 +01:00
Adam Ford
6001b49920 ARM: rmobile: Add Beacon EmbeddedWorks RZG2N Dev Kit
The Beacon EmbeddedWorks kit is based on the R8A774B1 SoC also
known as the RZ/G2N.

The kit consists of a SOM + Baseboard and supports microSD,
eMMC, Ethernet, a couple celular radios, two CAN interfaces,
Bluetooth and WiFi.  It shares much of the same design as
the RZ/G2M dev kit.

Signed-off-by: Adam Ford <aford173@gmail.com>
2021-02-07 21:12:57 +01:00
Simon Glass
2764cf5e97 x86: coral: Add sysinfo ops
These ops are missing at present which is not permitted. Add an empty
operation struct.

Note: If the uclass requires operations then the drivers should provide
them. Otherwise, checking for missing operations must be done in every
uclass operation, so it adds to code size.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2021-02-06 19:20:34 +08:00
Tom Rini
8308a28af8 Merge tag 'ti-v2021.04-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-ti
- Sync DTS from Linux kernel for all K3 platforms
- Add MMC higher speed nodes for AM65x, J721e, J7200
- Convert Nokia RX-51 to use CONFIG_DM_MMC
- Minor fixes for LEGO MINDSTORMS
2021-02-05 09:39:31 -05:00
David Lechner
f4e2c10a71 ARM: legoev3: drop bi_arch_number
This drops assigning bi_arch_number on LEGO MINDSTORMS EV3. This board
never had its own unique number and since we are using device tree,
we no longer need to pass an arch number to Linux.

Signed-off-by: David Lechner <david@lechnology.com>
2021-02-04 20:37:56 +05:30
David Lechner
68432b5d12 ARM: legoev3: set serial# env var
This sets the serial# environmet variable instead of using ATAGs on
LEGO MINDSTORMS EV3.

Also fix some nomenclature while we are touching this code (Bluetooth
address is not the same as MAC address, EEPROM version is not the same
as board version).

Signed-off-by: David Lechner <david@lechnology.com>
2021-02-04 20:37:56 +05:30
Pali Rohár
64fd2d2614 Nokia RX-51: Convert to CONFIG_DM_MMC
Move twl4030_power_mmc_init() from board_mmc_power_init() to misc_init_r()
and disable CONFIG_SYS_MALLOC_F. Otherwise U-Boot cannot initialize MMC.
Also disable CONFIG_CMD_SLEEP CONFIG_DM_DEVICE_REMOVE CONFIG_MMC_VERBOSE to
free some space.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2021-02-04 20:37:56 +05:30
Bin Meng
b7324b5d53 riscv: ax25-ae350: Cast addr with uintptr_t
addr was delcared as fdt_addr_t which is now a 64-bit address.
In a 32-bit build, this causes the following warning seen when
building ax25-ae350.c:

  warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]

Cast addr with uintptr_t.

Signed-off-by: Bin Meng <bin.meng@windriver.com>
2021-02-03 03:38:41 -07:00
Simon Glass
401d1c4f5d common: Drop asm/global_data.h from common header
Move this out of the common header and include it only where needed.  In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly.   Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-02-02 15:33:42 -05:00
Pali Rohár
9d716339fb arm: mvebu: Espressobin: Disable slot when emmc is not present
This change extends previous commit 061c6d1b23 ("arm: mvebu: Espressobin:
Detect presence of emmc at runtime") and when emmc is not present then emmc
is removed from U-Boot DM and corresponding slot is disabled. Therefore on
Espressobin board without soldered emmc, state of emmc hw should be same as
if emmc was disabled in DTS.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2021-01-27 07:29:43 +01:00
Dennis Gilmore
9c690314db ARM: mvebu: ClearFog make sure that SATA and UART images are buildable
SATA and UART ClearFog imaages are not buildable as ENV_SECT_SIZE is not defined
set values for both possible targets

Signed-off-by: Dennis Gilmore <dennis@ausil.us>
2021-01-27 07:25:39 +01:00
Dennis Gilmore
5a3db5d1af ARM: mvebu: helios4 adjust env sizes to enable SPI to work
mirror the clearfog setup to enable SPI to work

Signed-off-by: Dennis Gilmore <dennis@ausil.us>
2021-01-27 07:25:39 +01:00
Tom Rini
e262b2973e Merge https://gitlab.denx.de/u-boot/custodians/u-boot-sunxi
- New Allwinner H616 SoC support (sans Ethernet & USB)
- H6 DT update
- Tanix TX6 TV box support
- OrangePi 3 support
- OrangePi Zero2 (H616) support
2021-01-25 19:46:02 -05:00
Jernej Skrabec
38be6b8387 sunxi: Add support for OrangePi Zero2
OrangePi Zero2 is SBC based on Allwinner H616 with 1 GiB of RAM, SD card
support, gigabit ethernet, micro HDMI, WIFI, Bluetooth and 1 USB 2.0
port. It also has two GPIO headers which allows further peripherals to
be used.

The devicetree file is taken from v3 of the OrangePi Zero2 Linux
submission [1], which it's not yet merged.

[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/632084.html

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-25 21:52:01 +00:00
Jernej Skrabec
d0b07c15c2 sunxi: add support for R_I2C on H616
This port is needed for communication with PMIC. SPL uses it to set DRAM
voltage on H616 boards.

Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-25 21:52:01 +00:00
Jernej Skrabec
fbd37d8d28 sunxi: Add support for AXP305 PMIC
This PMIC can be found on H616 boards and it's very similar to AXP805
and AXP806.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-25 21:52:00 +00:00
Andre Przywara
e9ad1b8dc5 sunxi: Properly check for SATAPWR and MACPWR
The #ifdef CONFIG_xxxPWR conditionals were not working as expected, as
string Kconfig symbols are always "defined" from the preprocessor's
perspective. This lead to unnecessary calls to the GPIO routines, but
also always added a half a second delay to wait for a SATA disk to power
up. Many thanks to Peter for pointing this out!

Fix this by properly comparing the Kconfig symbols against the empty
string. strcmp() would be nicer for this, but GCC does not optimise this
away, probably due to our standalone compiler switches.

Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Samuel Holland <samuel@sholland.org> # Orange Pi WinPlus
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
2021-01-25 21:52:00 +00:00
Andre Heider
c81877a919 sunxi: Add support for Orange Pi 3
dts file is taken from Linux 5.11-rc1 tag.

The Bluetooth controller of this device ships with a default address,
use the new CONFIG_FIXUP_BDADDR option to fix it up.

Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
[Updated OrangePi 3 DT, rebase and config update]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-25 21:52:00 +00:00
Jernej Skrabec
a54b2925a6 sunxi: Add support for Tanix TX6
This commit adds support for Tanix TX6 TV box, based on H6. It's low end
H6 board, with 3 GiB of RAM, eMMC, fast ethernet, USB, IR and other
peripherals.

DT file is taken from Linux 5.11-rc1 release.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-25 21:52:00 +00:00
Tom Rini
c99be953e7 - MIPS: add support for Mediatek MT7620 SoCs
-----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEiQkHUH+J02LLC9InKPlOlyTyXBgFAmAN21EACgkQKPlOlyTy
 XBgzBw/+LUzGufIop4CimnEhqrfKRuoSKinRWhx8Lo4PyjF5SAwLgIyCWY95PoQf
 eDka+Ufyj1TbvqbPR+bhJbdL7wFrku3iKE7b0Ni8AamkmsyybxAVeyByen0Q1mSF
 q4KoPhKJmpdZOfrUVrXZBBwG7/T1WTHMrCc2ZSacR0G/IeimgLplT4sRk/uG1eFo
 uiKYf0/AjD28WNvlE9Dq0EZQA+KsTe/q7GQ79nOTuxYTOjbPA59WXTOtZMo1cPgc
 GhT1EJr4N7OcGvxgkiZ8Gs4mYMbFFVvMAUNW1Bsx4v1aYJyfgP0ua58gTnWSMn69
 OJNdxTs+JYBSIZd0B8gNf0P1ZQgrGACA1Vq4O3xJUImtkzp0tMID97ZwvAdhJQbo
 MhNrWcIxijrzWDHEGhnyZ0wyqWmSwznsrvIlS9hMuIxxmnYKveTwfkCeVcvkwvn7
 Nc1Pls1Lt2ViP8/Nygc+fAMg30vtp+NvSrbA53foka62sJMqmWAjPEprPPlJV0Z2
 qGJWCxIJ/1YAUjkNrEnSo/2A3SSAM8wA1ku6aT/Ju7NZCx/3m7sYXE+wQuxYlU2I
 zxQDO+2H0v0nlVVWebQZGZx8sn6Z4O+aGCLAkpJ9tqrViJYhy0Ti2QZi0Udcl1Ny
 lADQXQM2iPoQ2zJlO4AmzXCZ7DLrKVeS3hFFiVxRWK16apckz+o=
 =fKDK
 -----END PGP SIGNATURE-----

Merge tag 'mips-pull-2021-01-24' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips

- MIPS: add support for Mediatek MT7620 SoCs
2021-01-25 14:38:40 -05:00
Tom Rini
4057b98ff2 Changes for 2020.04
-------------------
 
 - new board:
 	Phytec phyCORE-i.MX8MP
 	i.MX8MN Beacon EmbeddedWorks devkit
 
 - Fixes:
 	several nanbcb fixes
 	fix for imx8mm_beacon
 - further switch to distro boot commands
 - DM:
 	DM Ether for MX6UL
 
 CI:
 
 https://gitlab.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/6013
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCYA7Oxw8cc2JhYmljQGRl
 bnguZGUACgkQ9PVl5Jpo76bFkACePFxGqlRiC88QcA42wgCbCEmsdtEAnR4TgXQ4
 aMH4tzrcK9Qvs7ULooDL
 =IZtF
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20210125' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

Changes for 2020.04
-------------------

- new board:
	Phytec phyCORE-i.MX8MP
	i.MX8MN Beacon EmbeddedWorks devkit

- Fixes:
	several nanbcb fixes
	fix for imx8mm_beacon
- further switch to distro boot commands
- DM:
	DM Ether for MX6UL

CI:

https://gitlab.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/6013
2021-01-25 09:02:35 -05:00
Tom Rini
aee5bcce35 Second set of u-boot-atmel features for 2021.04 cycle
-----BEGIN PGP SIGNATURE-----
 
 iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmAOkP8cHGV1Z2VuLmhy
 aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKedCACiDHgP71VKSOiYnEU4
 vHD/ANmfMXqnsL71PpSdagnBRAl4vpm46CnD+Mq7RtchxGDNufX6tWJSI04Ci0bC
 mfmIfVEjePOnuUayylJ55OlrtJVpBqJFPqxM6MFcIF7nRja1r5thV1jTLNu+b4sm
 gg2sk1mC/531Lxbk8S7x+diPymNRArEm3IEw+xEqUhsNVQCKjOEcxi/BWIB2prR3
 NxRSGdW3j4CKdBqt7uOL1bqApeQQ9m0/gm1tE3hMXUo09I7uXmb7U52aKb5cV8L+
 8ZOlbav6yaPACe3p9npp4K0ByXMmYHjeo1NZW4cvAoKfzragdu0Cv7f0ssVCgrlR
 p1e3
 =xS6A
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-atmel-2021.04-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel

Second set of u-boot-atmel features for 2021.04 cycle

This feature set includes macb updates for all interfaces and new
sama7g5 variant support; micrel ksz9031 DLL support; a new board from
Giant based on Adafruit feather form factor which contains a SAMA5D27
SoC; several fixes regarding the NAND flash PMECC block; and pincontrol
drive strength support for pio4 controller.
2021-01-25 09:01:28 -05:00
Weijie Gao
76880b08c4 mips: mtmips: add two reference boards for mt7620
The mt7620_rfb board supports integrated 10/100M PHYs plus two external
giga PHYs. It also has 8MB SPI-NOR, mini PCI-e x1 slot, SDHC and USB.

The mt7620_mt7530_rfb boards supports an external MT7530 giga switch and a
16MB SPI-NOR flash.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2021-01-24 21:39:26 +01:00
Adam Ford
8e95883e46 imx: Add support for i.MX8MN Beacon EmbeddedWorks devkit.
Beacon EmbeddedWorks is releasing a devkit based on the i.MX8M
Nano SoC consisting of baseboard + SOM.

The kit is based on the same design as the Beacon dev kit with
the i.MX8M Mini.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2021-01-23 14:01:49 +01:00
Marc Ferland
5df34feb24 arm: dart6ul: fix ddr size macro
The previous macro was off by one bit and so we were getting a ddr
size which was twice the real size. This commit refactors the macro so
it returns the right size in _bytes_ and modifies the printf call so the
size is still printed in MiB.

Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
2021-01-23 13:47:50 +01:00
Teresa Remmet
c661c511e9 board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support
Add initial support PHYTEC phyCORE-i.MX8MP SOM.

    Supported features:
     - 2GB LPDDR4 RAM
     - eMMC
     - external SD
     - debug UART2
     - watchdog

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
2021-01-23 11:30:32 +01:00
Marc Ferland
9452d58e10 arm: dart6ul: enable DM_ETH for the dart6ul
This patch converts the dart6ul ethernet support to DM_ETH and cleans
up the legacy ethernet code. The clean up, more specifically:

* moves the fec2 node and pin definition to the carrier board DTS
  since the phy associated with it is on the carrier board and not on
  the SoM;
* add the reset pin associated to each phy;
* separate the ethernet, mdio and reset pins of each fec so that they
  are easier to reference;
* add clock properties to the phy nodes since they are connected to the
  50Mhz ENET[12]_TX_CLK clock of the SoC;
* remove CONFIG_BOARD_EARLY_INIT_F since the function is now empty.

Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
2021-01-23 11:30:31 +01:00
Alice Guo
10a394ba68 board: imx8mp: add boot.cmd for distro boot on iMX8MP
Distro Boot requires a U-Boot-specific script named boot.scr or
boot.scr.uimg which contains boot commands to boot the system. The
boot.cmd is such a file. Use mkimage to generate boot.scr or
boot.scr.uimg from boot.cmd, and the command is:
mkimage -A arm -O linux -T script -C none -a 0 -e 0 -n "Distro Boot Script" -d boot.cmd boot.scr.uimg

The boot.cmd file is an example script and can be modified based on
needs. bootargs is set in this script and root uses the default value
"/dev/mmcblk1p2 rootwait rw" which can be changed by overriding mmcroot.

Signed-off-by: Alice Guo <alice.guo@nxp.com>
2021-01-23 11:30:31 +01:00
Alice Guo
9b8656bd2b board: imx8mm: add boot.cmd for distro boot on iMX8MM
Distro Boot requires a U-Boot-specific script named boot.scr or
boot.scr.uimg which contains boot commands to boot the system. The
boot.cmd is such a file. Use mkimage to generate boot.scr or
boot.scr.uimg from boot.cmd, and the command is:
mkimage -A arm -O linux -T script -C none -a 0 -e 0 -n "Distro Boot Script" -d boot.cmd boot.scr.uimg

The boot.cmd file is an example script and can be modified based on
needs. bootargs is set in this script and root uses the default value "
/dev/mmcblk1p2 rootwait rw" which can be changed by overriding mmcroot.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
2021-01-23 11:30:31 +01:00
Peng Fan
846b77e7df imx: imx8mn_ddr4_evk: Use CONFIG_TARGET_IMX8MN_DDR4_EVK for DDR4 EVK board
use CONFIG_TARGET_IMX8MN_DDR4_EVK for DDR4 EVK board, we will use
CONFIG_TARGET_IMX8MN_EVK for LPDDR4 EVK board.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-23 11:30:30 +01:00
Peng Fan
48b90f86c5 imx: imx8mp_evk: enable eth support
Add board code to configure the network interface
Add net defconfig

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-23 11:30:30 +01:00
Tom Rini
abd95385e7 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-samsung.git 2021-01-22 16:01:27 -05:00
Greg Gallagher
9119800591 board: atmel: Add SAMA5D27 giant board
Giant board is a tiny SBC based on the Adafruit Feather form factor,
created by groboards it contains a SAMA5D2 processor (SAMA5D27),
128 MB of RAM and a microSD card for storage.

Signed-off-by: Greg Gallagher <greg@embeddedgreg.com>
2021-01-22 15:09:59 +02:00
David Bauer
b821e0db46 rockchip: rk3328: Add support for FriendlyARM NanoPi R2S
This adds support for the NanoPi R2S from FriendlyArm.

Rockchip RK3328 SoC
1GB DDR4 RAM
Gigabit Ethernet (WAN)
Gigabit Ethernet (USB3) (LAN)
USB 2.0 Host Port
MicroSD slot
Reset button
WAN - LAN - SYS LED

Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
2021-01-21 11:58:35 +08:00
Michal Simek
a672b9871b xilinx: common: Do not touch CONFIG_XILINX_OF_BOARD_DTB_ADDR in SPL
This hook is used in full U-Boot that's why there is no reason to touch
this location from SPL. The hook was introduced for QEMU usage but none is
really running SPL on QEMU that's why it shouldn't break any usecase.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-01-20 08:34:53 +01:00
Michal Simek
506009fc10 xilinx: common: Change macro handling in board_fdt_blob_setup()
Remove ifdef logic which is handled by preprocessor and move it link time
optimization to get full compile code coverage.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-01-20 08:34:53 +01:00
Michal Simek
2784befbd7 xilinx: zynqmp: Save bootseq number for SD/EMMC boot modes
For systems which has both sdhci controllers enable it is worth to export
bootseq number for variables. Then the variable can be used in custom
scripts to tune logic for OS.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-01-20 08:34:53 +01:00
Chia-Wei, Wang
ccdb58dc0a configs: aspeed: Add defconfig for AST2600 EVB
Add the default configuration for the AST2600 EVB.

Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
2021-01-18 15:23:06 -05:00
Chia-Wei, Wang
4a84cf06aa aspeed: Add AST2600 platform support
Add low level platform initialization for the AST2600 SoC.
The 2-stage booting with U-Boot SPL are leveraged to support
different booting mode.

However, currently the patch supports only the booting from
memory-mapped SPI flash.

Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
2021-01-18 15:23:06 -05:00
Holger Brunck
cbfc3b76b0 km/kirkwood: enable USB support and the host controller driver
Our kirkwood device embeds a USB host controller that is now used
on some boards. This enables the support of USB and the corresponding
driver.

Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
2021-01-18 15:14:15 -05:00
Fabien Parent
c2984eb38e board: mediatek: pumpkin: initialize usb device
Initialize USB device on pumpkin if it is enabled in the config.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
2021-01-18 14:59:19 -05:00
Padmarao Begari
64413e1b7c riscv: Add Microchip MPFS Icicle Kit support
This patch adds Microchip MPFS Icicle Kit support. For now, only
NS16550 Serial, Microchip clock, Cadence eMMC and MACB drivers are
enabled. The Microchip MPFS Icicle defconfig by default builds
U-Boot for S-Mode because U-Boot on Microchip PolarFire SoC will run
in S-Mode as payload of HSS + OpenSBI.

Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
2021-01-18 11:06:38 +08:00
Sean Anderson
8f78e52794 riscv: Add support for SPI on Kendryte K210
This enables configs necessary for using SPI. The environment is saved to
the very end of SPI flash. This is unlikely to be overwritten unless the
entire flash is reprogrammed.

This also supplies a default bootcommand. It loads an image and device tree
from the first partition of the MMC. This is a minimal/least effort
bootcmd, so suggestions (especially in the form of patches) are welcome. I
didn't set up distro boot because I think it is unlikely that any
general-purpose linux distros will ever be ported to this board.

Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Chrstopher Obbard <obbardc@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
2021-01-18 11:06:26 +08:00
Tom Rini
83e13c3469 Merge branch '2021.04-rc' of https://github.com/lftan/u-boot
- Add ATF flow for SoC64 devices
- Update socfpgaimage to support print header and update padding flow
2021-01-15 07:55:11 -05:00
Tom Rini
ab1a425524 - Enable logging features for stm32mp15 boards
- Update MAINTAINERS emails for STI and STM32
 - Activate OF_LIVE for ST stm32mp15 boards
 - Switch to MCO2 for PHY 50 MHz clock for DHCOM boards
 - Correction in stm32prog command on uart: always flush DFU on start command
 - Update USB-C power detection algorithm on DK boards
 -----BEGIN PGP SIGNATURE-----
 
 iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl/+yLkACgkQ4rK92eCq
 k3X/Fgf/d/11WyQrVzvpr+nN+4Wl7J+ASmoUz0yKa6ri+lbvhLgh+JXbCRKgRPWu
 vNnI07pSoX/QeaMpGBU8Ztg/Onb9/pvffz4WMk1411GoyCpDFuuK3cVSIoqkPfu+
 XmgSX0u4BXtve1+ZdWfVBWXawUSEDMmGR3tmz1708c/s/oYpnVeRDcqiqzJ94cWE
 yt+SpMPVqMUVQ/rAGkE8ToSMxX7FusEa7SvCg4U2ikoRWs3kPpr/73+tRWlmgGxL
 sW8SXSKiOmFyheSBx3d2B9n00kDYTTrQmbW9hlMilZmji7CwZYxgTCMdX0x4DeFP
 RDajT2Yju1JmeM+Z8+Ke2tupzvy6QA==
 =oK8C
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-stm32-20210113' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm

- Enable logging features for stm32mp15 boards
- Update MAINTAINERS emails for STI and STM32
- Activate OF_LIVE for ST stm32mp15 boards
- Switch to MCO2 for PHY 50 MHz clock for DHCOM boards
- Correction in stm32prog command on uart: always flush DFU on start command
- Update USB-C power detection algorithm on DK boards
2021-01-13 15:00:53 -05:00
Tom Rini
795f8fd0b5 - sync amlogic GX & AXG DT to Linux 5.10
- Add new MESON_EE driver support for GXBB & AXG
 - Add support for Libretech-CC v2, Wetek Core2, Beelink GT-King/Pro boards
 - add driver for TDO tl070wsh30 panel driver
 - meson: isolate loading of socinfo
 - Add soc_rev to environment
 - Enable G12A support for saradc
 - Add correct mmcdev on VIM3(L) & Odroid-N2(C4)
 - Read MAC from fuses for VIM3 & VIM3L boards
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEPVPGJshWBf4d9CyLd9zb2sjISdEFAl/9rV0ACgkQd9zb2sjI
 SdFE0xAAtXzW98pKmC4C3a1FWcGSuBZK2gzUgKc8oTqBWodMTVLSmDGNbIpaES/+
 UySXSR0KJ5Qmu3jEZN2NYUKuABzylmIyT+5/sj1yN0zgxU2NB2//18uELNVKC4b+
 wtLna+SSebl8ofGuVzfYYCfbBS0S2Y+n9g2+WVu3s+D03WG5wrqEZy5RqKRf4OMZ
 MoQiDoLFms1GS6iLoidg/RMNme6efODAOTOVklHre2zeN3rjGei2URHdVtIeXcdG
 G3Wz9GVwR96UWTGY6JuXEGVpI459vHc4AcswnVcKNnILS/50tpSA9Gc0e0lXaDwT
 29DPehnoBkdbtIQ4szrAthGBITWhhgp2ksHaY5jyg38mVGF1/uu76kPUlCLxY5fL
 //3j/t+qaA3iwJq36tvZSKbprjA8sINN8Hsmi9+2Bzyv90sLfxY/x/DpeTVfWUQf
 UireG3iCYBkP5Mxr1kO+eJUoPAEe8BDJ+3AyVCjlMvKdomGFGCY0C/2LY54G8WS+
 el2Sj8XkTgtZQA/HXuXg1y2Cw54FWN6SXMVFXqZW5bu/w2GmeSOMEkFs3aFieCB7
 5UP+PiA3aM9Z6oXJReNnwc7iy+de8peZ/gpNCqWxr/jxg/C5d+Lg3kgbr961MyhU
 e97xab9p3f9raVOrYCAP7jVqAfTS39ZtAzSZlSJcK3Pls9wVxJI=
 =iIWq
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-amlogic-20210112' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic

- sync amlogic GX & AXG DT to Linux 5.10
- Add new MESON_EE driver support for GXBB & AXG
- Add support for Libretech-CC v2, Wetek Core2, Beelink GT-King/Pro boards
- add driver for TDO tl070wsh30 panel driver
- meson: isolate loading of socinfo
- Add soc_rev to environment
- Enable G12A support for saradc
- Add correct mmcdev on VIM3(L) & Odroid-N2(C4)
- Read MAC from fuses for VIM3 & VIM3L boards
2021-01-13 07:32:02 -05:00
Patrice Chotard
7ccaa31380 MAINTAINERS: Update STi and STM32 maintainers emails in remaining files
A previous series already update STMicroelectronics emails maintainers
but some files have been omitted (Makefile, .dts, .dtsi and .rst files).
Update Patrick and my email address with the one dedicated to upstream
activities.

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2021-01-13 09:52:58 +01:00
Michal Simek
635e233b22 ARM: stm32: Use firmware property instead of loadables
There shouldn't be a need to use loadables propertyn because u-boot can be
pointed by firmware property. This change should also speedup boot process
because loadables property is list of strings which code is going through.
On the other hand firmware can just point to one image.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13 09:52:58 +01:00
Patrice Chotard
42082bc61b board: stm32pm1: update USB-C power detection algorithm on DK boards
USB-C power supply which are Power Delivery compliant (USB-PD) are able
to provide different voltage/current (for example 5V/3A 9V/3A 12V/2.25A...)

In this case, the power supply need to negotiate the voltage/current to
use with the device using CC1/CC2 USB-C signals.

If this negotiation occurs during ADC measurement (done also on CC1/CC2
USB-C signals) some ADC acquisition can be corrupted which cause wrong
power supply current detection.

To avoid this, the power supply current detection algorithm is updated
as following:
  - perform an ADC measurement, if a 3A current is detected, continue the
    boot process.
  - else, wait 20ms (max tPDDebounce duration) to ensure that USB-PD
    negotiation is done and perform another ADC measurement.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2021-01-13 09:52:58 +01:00
Patrick Delaunay
705b5bf9bb board: st: common: migrate trace to dev and log macro
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13 09:52:58 +01:00
Patrick Delaunay
873bf44888 board: st: stm32mp1: migrate trace to dev and log macro
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13 09:52:58 +01:00
Jaehoon Chung
a654b6a5ae samsung: arndale: remove board_mmc_init function
Remove board_mmc_init function.
It will be probed with driver-model.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2021-01-13 13:49:38 +09:00
Tom Rini
ee6726be4f Merge tag 'ti-v2021.04-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-ti
- DM support for OMAP PWM backlight
- USB host mode support for AM654
- Minor SPI fixes
- Add support k2g ice board with 1GHz silicon
- Fix GTC programming for K3 devices
2021-01-12 09:32:48 -05:00
Tom Rini
996f217ea3 First set of u-boot-atmel features for 2021.04 cycle
-----BEGIN PGP SIGNATURE-----
 
 iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl/8S/0cHGV1Z2VuLmhy
 aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKFkB/9NBJq/+sgHZXRaMlAu
 ULNwOPoNsQxHQGwF88B1lC+H8LJjM+2gJ8MfJdWvHNlcSdtJjbWk0aQL+5LKSlyz
 G7l3BZ+AIYMOeTXay5mNUKnekXIr7c8tLoX8FH/Ih+bHFPt57qL0bbfznV66UCOp
 /o/yM8daPa9Kx1vPEpT2dC9bYXLXeQv6R+RMxwoc4Bk+R3OK7zoZ3Wdx0q9HvBwj
 iWHM49X2fBqqi5RS+ZI37AUzi8iysD3fOq0kWTJcCNaci8i8RZdzSyoaDuXhA63I
 EZJ7v9fUkW/bwTONVE9n2BX4xF9X/6R7P46l9dQISXAxsOBwsNRQPt8Ro7mCoc4K
 392o
 =LIK7
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-atmel-2021.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel

First set of u-boot-atmel features for 2021.04 cycle

This feature set includes the new board SAMA7G5 EK, the new evaluation
kit for Microchip AT91 SAMA7G5 SoC . The current board support includes
two configurations for booting from eMMC (SDMMC0), SD-Card (SDMMC1), and
support for two Ethernet interfaces.
2021-01-12 09:32:20 -05:00
Artem Lapkin
6bfa331a6e board: amlogic: vim3: fix setup ethernet mac from efuse
Fix reading built-in ethernet MAC address from efuse

NOTE: MAC is stored in ASCII format, 1bytes = 2characters by 0 offset

if mac from efuse not valid we use meson_generate_serial_ethaddr

NOTE: remake odroid-n2.c from Neil Armstrong <narmstrong@baylibre.com>

Signed-off-by: Artem Lapkin <art@khadas.com>
[narmstrong: remove MAC print & spurious new endline]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-12 14:25:55 +01:00
Dario Binacchi
ba149a5b7b board: ti: am335x-ice: get CDCE913 clock device
With support for other clock drivers, the potentially supported CDCE913
device can no longer be probed without specifying its DT node name.

Signed-off-by: Dario Binacchi <dariobin@libero.it>
2021-01-12 10:59:04 +05:30
Dario Binacchi
260cbc9af2 video: omap: move drivers to 'ti' directory
Add drivers/video/ti/ folder and move all TI's code in this folder for
better maintenance.

Signed-off-by: Dario Binacchi <dariobin@libero.it>
2021-01-12 10:59:04 +05:30
Lokesh Vutla
d2aa5727a5 board: ti: k2g: Add support for K2G ICE with 1GHz Silicon
Add board detection support for K2G ICE with FlagChip 1GHz silicon.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2021-01-12 10:21:41 +05:30
Aswath Govindraju
6f9d41403a board: ti: am65x: Set SERDES0 mux to PCIe to use USB 2.0 interface
It has been observed that setting SERDES0 lane mux to USB prevents USB 2.0
operation on USB0. Setting SERDES0 lane mux to non-USB when USB0 is used in
USB 2.0 only mode solves this issue. However, for USB3.0+2.0 operation this
issue is not present.

Implement this workaround by writing 1 to LANE_FUNC_SEL field in
CTRLMMR_SERDES0_CTRL register.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
2021-01-12 10:21:40 +05:30
Andre Heider
9267ff89ee sunxi: board: add a config option to fixup a Bluetooth address
Some Bluetooth controllers, like the BCM4345C5 of the Orange Pi 3,
ship with the controller default address.

Add a config option to fix it up so it can function properly.

Signed-off-by: Andre Heider <a.heider@gmail.com>
Tested-by: Ondrej Jirman <megous@megous.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
[rebased]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-11 23:19:34 +00:00
Andre Heider
928f4f4868 sunxi: board: extract creating a unique sid into a helper function
Refactor setup_environment() so we can use the created sid for a
Bluetooth address too.

Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[rebased]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-11 23:19:34 +00:00
Andy Shevchenko
92600edb43 sunxi: board: Move USB ethernet initialization to board_late_init()
For the sake of consistency (*) and order of initialization, i.e.
after we have got the ethernet address, interrupt and timer initialized,
try to initialize USB ethernet gadget.

*) for example, zynqmp uses same order.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-11 23:19:34 +00:00
Icenowy Zheng
ab3b53f30f sunxi: add PineCube board
PineCube is an IP camera development kit released by Pine64.

It comes with the following compoents:

- A mainboard with Sochip S3 SoC, a 16MByte SPI Flash, AXP209 PMIC,
a power-only microUSB connector, a USB Type-A connector, a 10/100Mbps
Ethernet port and FPC connectors for camera and daughter board.
- An OV5640-based camera module which is connected to the parallel CSI
bus of the mainboard.
- A daughterboard with several buttons, a SD slot, some IR LEDs, a
microphone and a speaker connector.

As the device tree is synchronized in a previous commit, just add it to
Makefile, create a new MAINTAINER item and provide a defconfig.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-11 23:19:33 +00:00
Tom Rini
d71be19902 Merge branch 'next'
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-01-11 13:55:03 -05:00
Marek Szyprowski
aa3c7912cb board: amlogic: add MMC boot device detection for environment load
Detect eMMC or SD card boot on Odroid-C4/N2 and Khadas VIM3(l) boards and
report proper MMC device for the environment loading code. This allows to
automatically load and store environment variables on the FAT partition
or RAW offset of the MMC device without the need to use different
configurations on eMMC and SD card.

To use this feature with environment stored on FAT partition, one has to
specify an empty device part (i.e. ":1" for the first partition) in
CONFIG_ENV_FAT_DEVICE_AND_PART to let the code to set the device to the
value returned by mmc_get_env_dev() function.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-11 14:59:55 +01:00
Christian Hewitt
b3be2ee656 boards: amlogic: add Beelink S922X board family support
Copied from Odroid N2. Add myself as maintainer.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-11 14:59:54 +01:00
Marek Szyprowski
d10037e976 board: amlogic: vim3: read ethernet MAC address from efuse
Add the board specific code for reading built-in ethernet MAC address
from efuse.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-11 14:59:54 +01:00
Christian Hewitt
d412a6015e boards: amlogic: update documentation for WeTek Core2
Update the device matrix and add build instructions.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: added wetek-core2.rst to q200 MAINTAINERS and added blank lines to fix build]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-11 14:59:54 +01:00
Christian Hewitt
ed430519cf boards: amlogic: add WeTek Core2 support
Add a config for the WeTek Core2, largely based on the VIM2 config.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: added wetek-core2_defconfig to q200 MAINTAINERS]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-11 14:59:54 +01:00
Pascal Vizeli
d42e7964d9 meson: Add soc_rev to environment
Add SoC revision to environment. This can be useful to select the
correct device tree at runtime (N2/N2+).

Signed-off-by: Pascal Vizeli <pvizeli@syshack.ch>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-11 14:59:54 +01:00
Jerome Brunet
ade0100a91 arm64: meson: add support for libretech-cc v2
Add support for the Amlogic based libretech cc version 2.
As version 1, it is based on the s905x SoC.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[narmstrong: Fixed libretech-cc.rst bullet points]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-11 14:59:54 +01:00
Lukasz Majewski
a062d8e610 xea: spl: Disable pull UP for GPIO0_2{35}
On the imx287 pin GPMI_WRN (GPIO0_25) no PullUP is available that can be
enabled.

To get the same behavior for both boot select pins (i.e. GPIO0_2{35})
disable pull UPs on both.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2021-01-08 08:41:50 -05:00
Eugen Hristev
a07d2a1121 board: atmel: sama7g5ek: add support for MAC address retreival
Obtain two MAC addresses from the two EEPROMs and configure the two
available Ethernet interfaces accordingly.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2021-01-07 09:44:16 +02:00
Eugen Hristev
0f8904b82d configs: sama7g5: add mmc config for sdmmc0
Add new config for storing environment from sdmmc0.
Also clean-up sama7g5ek_emmc1 to point to the proper mmc device.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2021-01-07 09:44:16 +02:00
Eugen Hristev
1d463d6735 board: atmel: sama7g5ek: add initial support for sama7g5ek
Add initial support for sama7g5 evaluation kit board.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2021-01-07 09:44:15 +02:00
Tom Rini
bc0b99bd8b Xilinx changes for v2021.04
arm64:
 - DT updates
 
 microblaze:
 - Add support for NOR device support
 
 spi:
 - Fix unaligned data write issue
 
 nand:
 - Minor code change
 
 xilinx:
 - Fru fix in limit calculation
 - Fill git repo link for all Xilinx boards
 
 video:
 - Add support for seps525 spi display
 
 tools:
 - Minor Vitis file support
 
 cmd/common
 - Minor code indentation fixes
 
 serial:
 - Uartlite debug uart initialization fix
 -----BEGIN PGP SIGNATURE-----
 
 iFsEABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX/ROlgAKCRDKSWXLKUoM
 IRC5AIkBzg4Sz8fQgdCiOK89k7tdFKMAnA9SYhgm4TSCzffZCJwnm78QoGAC
 =4FnY
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2021.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next

Xilinx changes for v2021.04

arm64:
- DT updates

microblaze:
- Add support for NOR device support

spi:
- Fix unaligned data write issue

nand:
- Minor code change

xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards

video:
- Add support for seps525 spi display

tools:
- Minor Vitis file support

cmd/common
- Minor code indentation fixes

serial:
- Uartlite debug uart initialization fix
2021-01-06 07:57:33 -05:00
Tom Rini
b11f634b1c Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
 dtoc: Tidy up and add more tests
 ns16550 code clean-up
 x86 and sandbox minor fixes for of-platdata
 dtoc prepration for adding build-time instantiation
 -----BEGIN PGP SIGNATURE-----
 
 iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
 bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
 KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
 HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
 59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
 2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
 LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
 =9kN3
 -----END PGP SIGNATURE-----

Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next

Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
2021-01-05 22:34:43 -05:00
Tom Rini
720620e691 Prepare v2021.01-rc5
-----BEGIN PGP SIGNATURE-----
 
 iQGzBAABCgAdFiEEGjx/cOCPqxcHgJu/FHw5/5Y0tywFAl/0YVIACgkQFHw5/5Y0
 tywtEwv/cJWlKgcSnYjuJrxwuJdauUTfXdbUgtCxOtBw/BP4dsKkbGTJPw5q5M+4
 LJJSKyksmJVTX26h1dpkzQjOpWtTDnWqm5CTIxD52oQD7pxK+zCQ9T6S+QbQD0Se
 ogHmZluzFoluxbNgo8tiO52xvMhDO3TVAzxsNDdGfkd5/tAXOHClPc34RmAkdRHU
 VsR89AKdT2q543fiUfrRZYDzdctaNWhRGXMDcJ4+QU/8hQhrpcr8EtHbF+3mWX4K
 pA01pDz150Rn4UI6S2xKEWrjSTHe55fxVj/Qj0rq9z2E/+NqGXemf5s13AR0G/z3
 PqHdVLHzDe64pbOvmyU1pVQ0aMb8vMJUnqx68SQZY3On2c+MjRWQ+7aVVaKOcPGp
 uatk6QMrggHp3Li+3yZrLBE0qPr/sNMVb7mUesdZb6lFd2VIs8siwhfeGXMS+nDI
 xePzsR43Fnn5Q5KIqqvcWUb+TTTqUDUff0wyAU8NBgCaIBIZK8h2ppS1jjnbms0I
 mr8Er2vb
 =Dfum
 -----END PGP SIGNATURE-----

Merge tag 'v2021.01-rc5' into next

Prepare v2021.01-rc5

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-01-05 16:20:26 -05:00
Tom Rini
c2d80bbde8 Merge tag 'ti-v2021.01-rc5' of https://gitlab.denx.de/u-boot/custodians/u-boot-ti
- Fix I2C speed for Nokia RX51
2021-01-05 16:10:33 -05:00
Simon Glass
65e25bea59 dm: Rename DM_GET_DRIVER() to DM_DRIVER_GET()
In the spirit of using the same base name for all of these related macros,
rename this to have the operation at the end. This is not widely used so
the impact is fairly small.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-01-05 12:26:35 -07:00
Simon Glass
20e442ab2d dm: Rename U_BOOT_DEVICE() to U_BOOT_DRVINFO()
The current macro is a misnomer since it does not declare a device
directly. Instead, it declares driver_info record which U-Boot uses at
runtime to create a device.

The distinction seems somewhat minor most of the time, but is becomes
quite confusing when we actually want to declare a device, with
of-platdata. We are left trying to distinguish between a device which
isn't actually device, and a device that is (perhaps an 'instance'?)

It seems better to rename this macro to describe what it actually is. The
macros is not widely used, since boards should use devicetree to declare
devices.

Rename it to U_BOOT_DRVINFO(), which indicates clearly that this is
declaring a new driver_info record, not a device.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-01-05 12:26:35 -07:00
Simon Glass
f10643cf8a dm: core: Access device ofnode through functions
At present ofnode is present in the device even if it is never used. With
of-platdata this field is not used, so can be removed. In preparation for
this, change the access to go through inline functions.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-01-05 12:24:41 -07:00
Simon Glass
8b842be10c x86: apl: Reduce size for TPL
Update various drivers to use of_match_ptr() and to avoid including debug
strings in TPL. Omit the WiFi driver entirely, since it is not used in
TPL.

This reduces the TPL binary size by about 608 bytes.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-01-05 12:24:41 -07:00
Simon Glass
2d6bf754ce serial: Rename ns16550 functions to lower case
Lower case should be used for function names. Update this driver and its
callers accordingly.

Signed-off-by: Simon Glass <sjg@chromium.org>

Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2021-01-05 12:24:40 -07:00
Simon Glass
d30c7209df serial: Update NS16550_t and struct NS16550
Typedefs should not be used in U-Boot and structs should be lower case.
Update the code to use struct ns16550 consistently.

Put a header guard on the file while we are here.

Signed-off-by: Simon Glass <sjg@chromium.org>

Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2021-01-05 12:24:40 -07:00
Pali Rohár
a8ef64e4ef Nokia RX-51: Decrease i2c speed to 100000
It looks like that i2c bus lot of times timeout on some units. Prior
migration to CONFIG_DM_I2C i2c speed was set to CONFIG_SYS_OMAP24_I2C_SPEED
value which was 100000. Lower speed fixes timeout problems, so change speed
back to its previous value.

Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 8d8c181703 ("Nokia RX-51: Convert to CONFIG_DM_I2C")
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2021-01-05 20:49:52 +05:30
Michal Simek
0109db1cd1 xilinx: Fill git repository for Xilinx boards
All Xilinx SoCs have repository location filled already but boards are
covered by different fragment which is missing this link.
The patch is extending description with adding proper link to the same
repository.

Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-01-05 11:54:53 +01:00
Heinrich Schuchardt
b6d14c52f9 fru: ops: avoid out of bounds access
Building xilinx_zynq_virt_defconfig fails on origin/next as reported by
GCC 10.2 (as provided by Debian Bullseye):

  CC      board/xilinx/common/fru_ops.o
board/xilinx/common/fru_ops.c: In function ‘fru_capture’:
board/xilinx/common/fru_ops.c:173:8:
error: array subscript 284 is outside array bounds of
‘struct fru_table[1]’ [-Werror=array-bounds]
  173 |  limit = data + sizeof(struct fru_board_data);
      |  ~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
board/xilinx/common/fru_ops.c:17:18: note: while referencing ‘fru_data’
   17 | struct fru_table fru_data __section(.data);
      |                  ^~~~~~~~

When using sizeof(struct fru_board_data) to find the end of the structure
you should add it to the start of the structure.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-01-05 11:54:53 +01:00