For consistency with board_should_run_oprom(), do the same to
should_load_oprom(). Board support codes can provide this one
to override the default weak one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present should_load_oprom() calls board_should_run_oprom() to
determine whether oprom should be loaded. But sometimes we just
want to load oprom without running. Make them independent.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch support the driver mode for exynos dwmmc controller.
To support the legacy model, maintained the existing code.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
If there is not "samsung,bus-width" property, use the 4bit buswidth by
default.
Almost all Exnyos SoCs support at least 4bit buswidth.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Clean the unused and unnecessary codse.
This patch is one of them for preparing to use DM.
Because it's easy to maintain and combine DM after cleaning codes.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
PERIPH_ID_SDMMC4(131) is not continous value with PERIPH_ID_SDMMC0(75).
If there is no 'index' property in fdt, then dev_index should be
assigned to dev_id(Peripheral ID).
At this time, dev_index should be "56". It means Exynos SoC has "56"
numbers of DWMMC IP. To prevent this behavior, it needs to check the
maximum device index.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Removed #ifdef for OF_CONTROL.
It might use 'OF_CONTROL' by default.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This function have maintained for supporting Non-FDT.
Now, Almost all SoC are changed to fdt style.
So there are no that this function is called anywhere.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The CONFIG_HIDE_LOGO_VERSION config can be used to disable putting the
U-Boot version string on top of the logo.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The cros-ec keyboard is always a child of the cros-ec node. Rather than
searching the device tree, looking at the children. Remove the compat string
which is now unused.
Signed-off-by: Simon Glass <sjg@chromium.org>
Define a platform data structure for the MPC85XX GPIO driver to allow
use of the driver without device tree. Users should define the GPIO
blocks for their platform like this:
struct mpc85xx_gpio_plat gpio_blocks[] = {
{
.addr = 0x130000,
.ngpios = 32,
},
{
.addr = 0x131000,
.ngpios = 32,
},
};
U_BOOT_DEVICES(my_platform_gpios) = {
{ "gpio_mpc85xx", &gpio_blocks[0] },
{ "gpio_mpc85xx", &gpio_blocks[1] },
};
This is intended to build upon the recent submission of the base
MPC85XX driver from Mario Six. We need to use that new driver
without dts support and this patch gives us that flexibility.
This has been tested on a Freescale T2080 CPU, although only the first
GPIO block.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Reviewed-by: Mario Six <mario.six@gdsys.cc>
Tested-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Simon Glass <sjg@chromium.org>
The driver model conversion for MMC has moved in small steps. The first step
was to have an MMC device (CONFIG_DM_MMC). The second was to use a child
block device (CONFIG_BLK). The final one is to use driver model for MMC
operations (CONFIG_DM_MMC_OP). Add support for this.
The immediate priority is to make all boards that use DM_MMC also use those
other two options. This will allow them to be removed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this code into separate functions so that it can be used from the uclass
also. Add static inline versions for when the option is disabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than having an #ifdef in the main mmc.c file, control this feature
from the Makefile by moving the code into its own file.
Signed-off-by: Simon Glass <sjg@chromium.org>
These private functions are used both in the driver-model implementation and
in the legacy code. Add them to the header.
Signed-off-by: Simon Glass <sjg@chromium.org>
In case of DT boot, don't read default speed and mode for SPI from
CONFIG_*, instead read from DT node. This will make sure that boards
with multiple SPI/QSPI controllers can be probed at different
bus frequencies and SPI modes.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Instead of relying on CONFIG_SPI_FLASH_QUAD to be defined to enable QUAD
mode, make use of mode_rx field of dm_spi_slave_platdata to determine
whether to enable or disable QUAD mode. This is necessary to support
muliple SPI controllers where one of them may not support QUAD mode.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
AHB address can be as long as 32 bit, hence remove the
CQSPI_REG_INDIRECTRDSTARTADDR mask. Since AHB address is passed from DT
and read as u32 value, it anyway does not make sense to mask upper bits.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Convert davinci_spi driver so that it complies with SPI DM framework.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This API helps to map physical register addresss pace of device to
virtual address space easily. Its just a wrapper around map_physmem()
with MAP_NOCACHE flag.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Add support for standard type SCI (without FIFO) port.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
MMC core expects (now) valid mmc->dev pointer.
During conversion in commit cffe5d86 not every driver was updated.
This patch fixes crash while accessing MMC on
boards using Qualcomm SDHCI controller.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Return value of rtl_send_common propogates unmodified all the way
up to eth_send and further to API consumer if CONFIG_API is enabled.
Previously rtl_send_common returned number of bytes sent on success
which was erroneouly detected as error condition by API consumers
that checked for operation success by comparing return value with 0.
Switch rtl_send_common to use common convention: return 0 on success
and negative value for failure.
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Oleksandr Tymoshenko <gonzo@bluezbox.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds support for aquantia AQR106/107 PHY.
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit 90b7fc924a "net: designware: support phy reset device-tree
bindings" made DW GMAC driver dependent on DM_GPIO by unconditional
usage of purely DM_GPIO stuff like:
* dm_gpio_XXX()
* gpio_request_by_name()
But since that driver as of today might be easily used without
DM_GPIO (that's the case for Synopsys AXS10x boards) we're
shielding all DM_GPIO things by ifdefs.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This seems to give the best performance, so let's use it always.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We have standard drivers for panels and backlights which can do most of the
work for us. Move the tegra20 LCD driver over to use those instead of custom
code.
This patch includes device tree changes for the nvidia boards. I have only
been able to test seaboard. If this patch is applied, these boards will
also need to be synced with the kernel, and updated to use display-timings:
- colibri
- medcom-wide
- paz00
- tec
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On recent SoCs, tegra_pcie_phy_enable() isn't called; but instead
tegra_pcie_enable_controller() calls tegra_xusb_phy_enable(). However,
part of tegra_pcie_phy_enable() needs to happen in all cases. Move that
code to tegra_pcie_port_enable() instead.
For reference, NVIDIA's downstream Linux kernel performs this operation
in tegra_pcie_enable_rp_features(), which is called immediately after
tegra_pcie_port_enable(). Since that function doesn't exist in the U-Boot
driver, we'll just add it to the tail of tegra_pcie_port_enable() instead.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The value that should be programmed into the PADS_REFCLK register varies
per SoC. Fix the Tegra PCIe driver to program the correct values. Future
SoCs will require different values in cfg0/1, so the two values are stored
separately in the per-SoC data structures.
For reference, the values are all documented in NV bug 1771116 comment 20.
The Tegra210 value doesn't match the current TRM, but I've filed a bug to
get the TRM fixed. Earlier TRMs don't document the value this register
should contain, but the ASIC team has validated all these values, except
for the Tegra20 value which is simply left unchanged in this patch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Waiting 30 seconds for the hpd to go high seems a bit much, especially
on headless boots. Lowering the timeout to 300ms.
Sending as RFC because frankly i don't know what a sensible timeout is
here, but 30 seconds is clearly not it :)
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Dropped RFC tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
Otherwise, ocassionally see errors like this:
Flashing sparse image at offset 2078720
Flashing Sparse Image
sdhci_send_command: Timeout for status update!
mmc fail to send stop cmd
write_sparse_image: Write failed, block #2181088 [0]
This does not affect the actual writing speed, which is controlled by
the default value:
CONFIG_SDHCI_CMD_DEFAULT_TIMEOUT
It only increases the retries when reading:
SDHCI_INT_STATUS
to avoid the timeout error.
Signed-off-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Correcting QSPI disable/unselect CS reset value.
CTRL_CORE_CONTROL_IO_2: QSPI_MEMMAPPED_CS[10:8]
This is not causing any issue, but its better
to untouch the reserved bits.
Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
PH1-LD4 and PH1-sLD8 SoCs have pins that support pin configuration
(pin biasing, drive strength control), but not pin-muxing.
Allow to fill the mux value table with -1 for those pins; pins with
mux value -1 will be skipped in the pin-mux set function. The mux
value type should be changed from "unsigned" to "int" in order to
accommodate -1 as a special case.
[ Linux commit: 363c90e743b50a432a91a211dd8b078d9df446e9 ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
PH1-LD11 and PH1-LD20 have much pin controlling in common, so I
added a single driver shared between them in the initial commit.
However, the Ethernet pin-mux settings I am going to add are
different with each other, and they may diverge more as the
progress of development. Split it into two dedicated drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, the UniPhier pinctrl driver itself is a syscon, but it
turned out much more reasonable to make it a child node of a syscon
because our syscon node consists of a bunch of system configuration
registers, not only pinctrl, but also phy, and misc registers.
It is difficult to split the node. This commit allows to migrate to
the new DT structure.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Freescale ARMv8 SoC name ends with "A" to represent ARM SoCs.
like LS2080A, LS1043A, LS1012A.
So append "A" to SoC names.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Introudce wp_enable. To check WPSPL, wp_enable needs to be set
to 1 in board code.
Take i.MX6UL for example, for some boards, they do not use WP singal,
so they does not configure USDHC1_WP_SELECT_INPUT, and its default
value is 0(GPIO1_IO02). However GPIO1_IO02 is muxed for i2c usage and
SION bit set. So USDHC controller can always get wp signal and WPSPL
shows write protect and blocks driver continuing. This is not what
we want to see, so add wp_enable, and if set to 0, just omit the
WPSPL checking and this does not effect normal working of usdhc
controller.
If wp-gpios is provided in dts, wp_enable is set to 1, otherwise 0.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The USDHC moves the 4 clock bits CARD_CLK_SOFT_EN, IPG_PERCLK_SOFT_EN,
HCLK_SOFT_EN, and IPG_CLK_SOFT_EN from sysctl register to vendorspec
register. The driver uses RSTA to replace the clock gate off
operation. But this is not a good solution because:
1. when using RSTA, we should wait this bit to clear by itself. This is not
implemeneted in the code.
2. After RSTA is set, it is recommended that the Host Driver reset the
external card and reinitialize it.
So in this patch, we change to use the vendorspec registers for these bits
operation.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When booting in eMMC fast boot, MMC host does not exit from
boot mode after bootrom loading image. So the first command
'CMD0' sent in uboot will pull down the CMD line to low and
cause errors.
This patch cleans the MMC boot register in "mmc_init" to put the
MMC host back to normal mode.
Also clear DLL_CTRL delay line settings at USDHC initialization
to eliminate the pre-settings from boot rom.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
- update fastboot_okay() and fastboot_fail()
This file originally came from upstream code.
While retaining the storage abstraction feature, this is the second
set of the changes required to resync with the
cmd_flash_mmc_sparse_img()
in the file
aboot.c
from
https://us.codeaurora.org/cgit/quic/la/kernel/lk/plain/app/aboot/aboot.c?h=LE.BR.1.2.1
Signed-off-by: Steve Rae <srae@broadcom.com>
This "session-id" alogrithm is not required, and currently corrupts
the stored image whenever more the one "session" is required.
Signed-off-by: Steve Rae <srae@broadcom.com>
These condition checking are wrong.
Original Author's intention might be "&" instead of "&&".
It can know whether receive or transmit data request with
BIT[4]/BIT[5] of RINTSTS register.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The USBNC_PHYCFG2_ACAENB bit should be cleared to enable the
OTG ID detection, not set it. When the bit is set, the ACA
Resistance Detection is enabled, which disables the OTG ID
detection, because the internal pull up is off.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There is a 4 bytes hole between phy_cfg2 and phy_status, fix the
usbnc_regs structure to include the hole.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
clk->id is unsigned, so it can't be < 0. Remove the check for that.
FWIW, this issue was introduced when the clock API converted e.g.
clk_get_rate()'s clock ID parameter from an int to an unsigned long
(with a struct clk), without removing this check.
Fixes: 135aa95002 ("clk: convert API to match reset/mailbox style")
Reported-by: Coverity Scan
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
This empty line should not be there. Remove it.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Commit a058052c "net: phy: do not read configuration register on reset",
changes the behaviour of the phy_reset function such that the state of
the BMCR register is not preserved during reset.
Change the config function for the m88e1310 so that it does not do a
reset after configuring auto-negotiation.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch adds a phy driver for the Micrel KSZ886x switches.
Similarly to the KSZ8895, SoC MAC is directly connected to the switch
MAC on the switch CPU port, so the link to the switch is always up.
KSZ886x switches can be used in the following configuration modes:
- Unmanaged mode with config stored in external EEPROM
- Managed mode over SPI
- Managed mode over I2C
- Managed mode over mdio/mdc (aka MIIM or SMI)
This patch supports only unmanaged and MIIM modes.
Based on Micrel KSZ886x driver from Linux kernel and
Micrel KSZ8895 driver from U-Boot.
Verified with the KSZ8863MLL.
Signed-off-by: Alexey Firago <alexey_firago@mentor.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The rtl8169 driver uses a global variable to store the register address
of the adapter being operated upon. This is updated to point at the
correct adapter when sending or receiving a packet, or shutting down the
adapter, but not when initializing the adapter. Consequently, switching
between different adapters within the same U-Boot runtime does not work
correctly since the driver programs the wrong registers during
rtl8169_eth_start() -> rtl8169_common_start() -> rtl8169_hw_start().
Note that since rtl8169_eth_stop() does set the global variable, the
second consecutive attempt to use the "new" adapter did work even before
this patch, because each time network usage is shut down, the network
core calls stop, which sets the variable so that the next start does
actually initialize the hardware, and the adapter works.
Equally, rtl8169_eth_probe() calls rtl_init() which sets the global, so
if using only a single device, or if picking the "right" device (based on
probe order) when multiple devices are present, ioaddr will already be set
correctly from the get-go, so the issue does not occur.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some drivers are still directly accessing the chip->mtd field. Patch
them to use nand_to_mtd() instead.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
NAND chips are supposed to expose their capabilities through advanced
mechanisms like READID, ONFI or JEDEC parameter tables. While those
methods are appropriate for the bootloader itself, it's way to
complicated and takes too much space to fit in the SPL.
Replace those mechanisms by a dumb 'trial and error' mechanism.
With this new approach we can get rid of the fixed config list that was
used in the sunxi NAND SPL driver.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Split the 'load page' and 'read page' logic in 2 different functions so
we can later load the page and test different ECC configs without the
penalty of reloading the same page in the NAND cache.
We also move common setup to a dedicated function (nand_apply_config()) to
avoid rewriting the same values in NFC registers each time we read a page.
These new functions are passed a pointer to an nfc_config struct to limit
the number of parameters.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
check_value_xxx() helpers are using a 1ms delay between each test, which
can be quite long for some operations (like a page read on an SLC NAND).
Since we don't have anything to do but to poll this register, reduce the
delay between each test to 1us.
While we're at it, rename the max_number_of_retries parameters and the
MAX_RETRIES macro into timeout_us and DEFAULT_TIMEOUT_US to reflect that
we're actually waiting a given amount of time and not only a number of
retries.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Use CONFIG_SYS_NAND_U_BOOT_OFFS_REDUND value instead of trying to guess
where the redundant u-boot image is based on simple (and most of the time
erroneous) heuristics.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
# Conflicts:
# drivers/mtd/nand/sunxi_nand_spl.c
On modern NAND it's more than recommended to have a backup copy of the
u-boot binary to recover from corruption: bitflips are quite common on
MLC NANDs, and the read-disturbance will corrupt your u-boot partitition
more quickly than what you would see on an SLC NAND.
Add an extra Kconfig option to specify the offset of the redundant u-boot
image.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
[scottwood: added ifdef to fix build break]
Signed-off-by: Scott Wood <oss@buserror.net>
The SYS_NAND_U_BOOT_OFFS is quite generic, but the Kconfig entry is forced
to explicitly depend on platforms that are not already defining it in their
include/configs/<board>.h header.
Add the SYS_NAND_U_BOOT_LOCATIONS option, make the SYS_NAND_U_BOOT_OFFS
depends on it, remove the dependency on NAND_SUNXI and make it dependent
on SPL selection.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The sunxi SPL NAND controller driver supports use 'BootROM'-like configs,
that is, configs where the ECC bytes and real data are interleaved in the
page instead of putting ECC bytes in the OOB area.
Doing that has several drawbacks:
- since you're interleaving data and ECC bytes you can't use the whole page
otherwise you might override the bad block marker with non-FF bytes.
- to solve the bad block marker problem, the ROM code supports partially
using the page, but this introduces a huge penalty both in term of read
speed and NAND memory usage. While this is fine for rather small
binaries(like the SPL one which is at maximum 24KB large), it becomes
non-negligible for the bootloader image (several hundred of KB).
- auto-detection of the page size is not reliable (this is in my opinion
the biggest problem). If you get the page size wrong, you'll end up
reading data at a different offset than what was specified by the caller
and the reading may succeed (if valid data were written at this address).
For all those reasons I think it's wiser to completely remove support for
'syndrome' configs. If we ever need to support it again, then I'd recommend
specifying all the config parameters through Kconfig options.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The following changes are made to the clock API:
* The concept of "clocks" and "peripheral clocks" are unified; each clock
provider now implements a single set of clocks. This provides a simpler
conceptual interface to clients, and better aligns with device tree
clock bindings.
* Clocks are now identified with a single "struct clk", rather than
requiring clients to store the clock provider device and clock identity
values separately. For simple clock consumers, this isolates clients
from internal details of the clock API.
* clk.h is split so it only contains the client/consumer API, whereas
clk-uclass.h contains the provider API. This aligns with the recently
added reset and mailbox APIs.
* clk_ops .of_xlate(), .request(), and .free() are added so providers
can customize these operations if needed. This also aligns with the
recently added reset and mailbox APIs.
* clk_disable() is added.
* All users of the current clock APIs are updated.
* Sandbox clock tests are updated to exercise clock lookup via DT, and
clock enable/disable.
* rkclk_get_clk() is removed and replaced with standard APIs.
Buildman shows no clock-related errors for any board for which buildman
can download a toolchain.
test/py passes for sandbox (which invokes the dm clk test amongst
others).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
This adds a sandbox reset implementation (provider), a test client
device, instantiates them both from Sandbox's DT, and adds a DM test
that excercises everything.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
A reset controller is a hardware module that controls reset signals that
affect other hardware modules or chips.
This patch defines a standard API that connects reset clients (i.e. the
drivers for devices affected by reset signals) to drivers for reset
controllers/providers. Initially, DT is the only supported method for
connecting the two.
The DT binding specification (reset.txt) was taken from Linux kernel
v4.5's Documentation/devicetree/bindings/reset/reset.txt.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tegra186's HSP module implements doorbells, mailboxes, semaphores, and
shared interrupts. This patch provides a driver for HSP, and hooks it
into the mailbox API. Currently, only doorbells are supported.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Rename mailbox*.h to match the naming convention requested during review
of the new reset subsystem.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
A bug in the pca953x driver prevents correct reading of GPIO input
values beyond the 8th GPIO; all values are reported as zero. Setting of
GPIO output values is not affected.
This patch fixes the reading behavior.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Peng Fan <van.freenix@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Some architectures as m68k still need to use CONFIG_NEEDS_MANUAL_RELOC,
and are not still using the device tree.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Acked-by: Simon Glass <sjg@chromium.org>
If the usb controller is not running, no need to shutdown it,
otherwise `usb stop` complains about:
"EHCI failed to shut down host controller".
To i.MX7D SDB, there are two usb ports, one Host, one OTG.
If we only plug one udisk to the Host port and then `usb start`,
the OTG controller for OTG port does not run actually. Then,
if `usb stop`, the OTG controller for OTG port will also be
shutdown, but it is not running.
This patch adds a check to only shutdown the running controller.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: "Stefan Brüns" <stefan.bruens@rwth-aachen.de>
Cc: Stephen Warren <swarren@nvidia.com>
This patch is doing the following:
1. Implementing the errata for LS2080.
2. Adding fixup for fdt for LS2080.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
This patch does the following things:
1. Makes the errata checking code common for PPC and ARM
2. Moves all these static inline functions into a dedicated C file
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Performs code cleanup for device tree fixup for fsl usb controllers by
making functions to handle these similar errata checking code.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Define CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8 to allow the
physical interface to be 8-bit (rather than 16-bit).
Signed-off-by: Steve Rae <srae@broadcom.com>
Add initial support for NXP's S32V234 SoC and S32V234EVB board.
The S32V230 family is designed to support computation-intensive applications
for image processing. The S32V234, as part of the S32V230 family, is a
high-performance automotive processor designed to support safe
computation-intensive applications in the area of vision and sensor fusion.
Code originally writen by:
Original-signed-off-by: Stoica Cosmin-Stefan <cosminstefan.stoica@freescale.com>
Original-signed-off-by: Mihaela Martinas <Mihaela.Martinas@freescale.com>
Original-signed-off-by: Eddy Petrișor <eddy.petrisor@gmail.com>
Signed-off-by: Eddy Petrișor <eddy.petrisor@nxp.com>
The Linflex module is integrated on some NXP automotive SoCs part of the former
Freescale portfolio, like S32V234, an SoC for Advanced Driver Assistance
Systems.
Original-signed-off-by: Stoica Cosmin-Stefan <cosminstefan.stoica@freescale.com>
Original-signed-off-by: Chircu Bogdan <Bogdan.Chircu@freescale.com>
Original-signed-off-by: Depons Eric <eric.depons@freescale.com>
Original-signed-off-by: Eddy Petrișor <eddy.petrisor@gmail.com>
Signed-off-by: Eddy Petrișor <eddy.petrisor@gmail.com>
Add device tree support.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add driver-model support to this driver. Most features can be controlled
from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Adjust the driver to use struct display_timing for its display timing.
This is what is used by driver-model and allows the LCD init code to be
common.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
This needs to be set to avoid a fatal error when ECC is used.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
This uses the wrote base register value. Fix it.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Add driver-model support to this driver. The old code remains for now so
that we can convert boards one at a time.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-on: smartweb, corvus, taurus, axm
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
The end address of the cache flush must be cache-line-aligned since
otherwise (at least on ARM926-EJS) the request is ignored. When the cache
is enabled this means that packets are not sent.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Adjust this driver to avoid using struct netdev in functions that driver
model will call. Also refactor the receive function to be compatible with
driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-on: smartweb, corvus, taurus, axm
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
On systems with PIO3 (SAMA5D3/D4/..), the pullup and pulldown configuration
is mutualy exclusive. This patch assures that the opposite pull resistor gets
disabled before the requested pull resistor is enabled. This changes behavior
of at91_set_pio_pulldown() such that the pullup is only disabled if pulldown
is to be enabled. This changes behavior of at91_set_pio_pullup() such that
the pulldown is only disabled if pullup is to be enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Josh Wu <josh.wu@atmel.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
This allows a board to configure verified boot within the SPL using
a FIT or FIT with external data. It also allows the SPL to perform
signature verification without needing relocation.
The board configuration will need to add the following feature defines:
CONFIG_SPL_CRYPTO_SUPPORT
CONFIG_SPL_HASH_SUPPORT
CONFIG_SPL_SHA256
In this example, SHA256 is the only selected hashing algorithm.
And the following booleans:
CONFIG_SPL=y
CONFIG_SPL_DM=y
CONFIG_SPL_LOAD_FIT=y
CONFIG_SPL_FIT=y
CONFIG_SPL_OF_CONTROL=y
CONFIG_SPL_OF_LIBFDT=y
CONFIG_SPL_FIT_SIGNATURE=y
Signed-off-by: Teddy Reed <teddy.reed@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Andreas Dannenberg <dannenberg@ti.com>
Acked-by: Sumit Garg <sumit.garg@nxp.com>
Now that we have set up pin control in cpu_init_r(), remove the
duplicated codes in the broadwell gpio driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present pinctrl driver gets probed in ich6_gpio driver's probe
routine, which has two issues:
- Pin's PADs only gets configured when GPIO driver is probed, which
is not done by default. This leaves the board in a partially
functional state as we must initialize PADs correctly to get
perepherals fully working.
- The probe routine of pinctrl driver is called multiple times, as
normally there are multiple GPIO controllers. It should really
be called just once.
Move the call to syscon_get_by_driver_data() from ich6_gpio driver
to cpu_init_r().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
The call to syscon_get_by_driver_data() does not save its return value.
Print it out to aid debugging.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add early i2c init function with conservative divider when the exact
clock rate is not available.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This driver implements SPI protocol in master mode to communicate
with the SPI device connected on SPI bus. It handles /CS explicitly
by controlling respective pin as gpio ('cs-gpios' property in dt node)
and uses PIO mode for SPI transaction. It is configurable based
on driver-model only.
Cc: Jagan Teki <jteki@openedev.com>
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Turn of the clock and assert the reset when musb_stop gets called, so that
the os gets the musb controller in a pristine state. This fixes a spurious
VBus error interrupt triggering as soon as the Linux musb driver loads.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
writting to ubi nand partitions need after write ends an erase
of the remaining sectors. This fail, if dfu write size was not
a multiple of erasesize, example log:
Failure erase: -1
Fix this error.
Signed-off-by: Heiko Schocher <hs@denx.de>
add for nand devices mtd concat support. Generic MTD concat
support is already ported to mainline, and used in the cfi_mtd
driver. This patch adds it similiar for nand devices.
Signed-off-by: Heiko Schocher <hs@denx.de>
Enable 8bit interface on HSMMC2 for am33xx to support 8bit eMMC chips.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
revert patch:
commit: 6b2221b008e0: mmc: Handle switch error status bit in MMC card status
to get eMMC working on shc board
Signed-off-by: Heiko Schocher <hs@denx.de>
Add some tests for the new open drain setting feature of the GPIO
uclass, and extend the capabilities of the sandbox GPIO driver
accordingly.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch implements the open-drain setting feature for the MPC85XX
GPIO controller.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Certain GPIO devices have the capability to switch their GPIOs into
open-drain mode, that is, instead of actively driving the output
(Push-pull output), the pin is connected to the collector (for a NPN
transistor) or the drain (for a MOSFET) of a transistor, respectively.
The pin then either forms an open circuit or a connection to ground,
depending on the state of the transistor.
This patch adds functions to the GPIO uclass to switch GPIOs to
open-drain mode on devices that support it.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds a driver for the built-in GPIO controller of the MPC85XX
SoC (probably supporting other PowerQUICC III SoCs as well).
Each GPIO bank is identified by its own entry in the device tree, i.e.
gpio-controller@fc00 {
#gpio-cells = <2>;
compatible = "fsl,pq3-gpio";
reg = <0xfc00 0x100>
}
By default, each bank is assumed to have 32 GPIOs, but the ngpios
setting is honored, so the number of GPIOs for each bank in configurable
to match the actual GPIO count of the SoC (e.g. the 32/32/23 banks of
the P1022 SoC).
The usual functions of GPIO drivers (setting input/output mode and output
value setting) are supported.
The driver has been tested on MPC85XX, but it is likely that other
PowerQUICC III devices will work as well.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Updates the NAND code to match Linux v4.6. The previous sync was from
Linux v4.1 in commit d3963721d9.
Note that none of the individual NAND drivers tracked Linux closely
enough to be synced themselves, other than manually applying a few
cross-tree changes.
Signed-off-by: Scott Wood <oss@buserror.net>
Tested-by: Heiko Schocher <hs@denx.de>
This change is part of the Linux 4.6 sync. It is being done before the
main sync patch in order to make it easier to address the issue across
all NAND drivers (many/most of which do not closely track their Linux
counterparts) separately from other merge issues.
Signed-off-by: Scott Wood <oss@buserror.net>
These functions are part of the Linux 4.6 sync. They are being added
before the main sync patch in order to make it easier to address the
issue across all NAND drivers (many/most of which do not closely track
their Linux counterparts) separately from other merge issues.
Signed-off-by: Scott Wood <oss@buserror.net>
nand_info[] is now an array of pointers, with the actual mtd_info
instance embedded in struct nand_chip.
This is in preparation for syncing the NAND code with Linux 4.6,
which makes the same change to struct nand_chip. It's in a separate
commit due to the large amount of changes required to accommodate the
change to nand_info[].
Signed-off-by: Scott Wood <oss@buserror.net>
Commit ad4f54ea86 ("arm: Remove palmtreo680 board") removed the only
user of the docg4 driver and the palmtreo680 image flashing tool. This
patch removes them.
Signed-off-by: Scott Wood <oss@buserror.net>
Cc: Mike Dunn <mikedunn@newsguy.com>
Cc: Simon Glass <sjg@chromium.org>
This driver is not used by anyone, remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Scott Wood <oss@buserror.net>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Correct the nand ecc initialization code
This fixes the issue of incorrect nand ecc
init if no device is found in ecc_matrix then
it endsup ecc init with junk initialization
instead of the most suited one.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Create an entry for "config USB_XHCI_DWC3" in Kconfig and
switch over to it for all boards.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move CONFIG_USB_XHCI to defconfig files for all boards, renaming it
into CONFIG_USB_XHCI_HCD.
As commented in the help of "config USB_XHCI" entry, this has been
a TODO for a long time; now CONFIG_USB_XHCI_HCD and CONFIG_USB_XHCI
have been unified in favor of the former.
Note:
Some boards define CONFIG_USB_XHCI in their headers without
CONFIG_USB, which does not meet the "depends on" in Kconfig.
I added CONFIG_USB=y for those boards when converting.
Otherwise, they would fail to build.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Serial number, vendor id and page size are added for QSPI flash
common on both LS1012AQDS and LS1012ARDB i.e. S25FS512SDSMFI011.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add condition of checking the enabled of address parity
for erratum A-009803, if parity is not enabled, the
workaround of erratum A-009803 should not be applied.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When multiple PCI cards are present in an ls2080a board, the second
card does not get its msi-map set up properly due to a bug in
computing the bus number.
The bus number returned by PCI_BDF() is not the actual PCI bus
number, but instead represents a global u-boot PCI bus number. A
given bus number is relative to hose->first_busno, so that has to be
subtracted from the PCI device id.
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Acked-by: Stuart Yoder <stuart.yoder@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Commit 34e026f9 added one extra bit to wr_lat for timing_cfg_2, but
with wrong bit position. It is bit 13 in big-endian, or left shift
18 from LSB. This error hasn't had any impact because we don't have
fast enough DDR4 using the extra bit so far.
Signed-off-by: York Sun <york.sun@nxp.com>
In function check_and_invalidate_dcache_range(), there are incorrect
start address and end address of the dcache range calculated for
Layerscape platforms. This patch is to fix this issue.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The clk_adjust is of SDRAM_CLK_CNTL[5:8] 4-bits on MPC85xx and P-series,
but is of SDRAM_CLK_CNTL[5:9] 5-bits on T-series and LS-series SoCs.
We should update it to adapt the case that clk_adjust is odd data.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The index returned by get_sys_clk_index() is not exactly what we expect.
Let's not rely on that and use get_sys_clk_freq() instead.
This fixes missing USB3 devices in the Linux kernel when USB is started
in u-boot. It still doesn't fix missing USB3 devices in u-boot though.
Signed-off-by: Roger Quadros <rogerq@ti.com>
The CONFIG_OMAP1510 is no longer defined, so remove this dead code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Nishanth Menon <nm@ti.com>
The ns16550 driver needs serial_in_shift() and serial_out_shift()
when compiled in debug UART mode, so shift the DM_SERIAL check a
little to make these functions available.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The MXS certainly does not support any sort of networking in GPIO code,
remove the netdev.h header.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tegra186's MMC controller needs to be explicitly identified. Add another
compatible value for it.
Tegra186 will use an entirely different clock/reset control mechanism to
existing chips, and will use standard clock/reset APIs rather than the
existing Tegra-specific custom APIs. The driver support for that isn't
ready yet, so simply disable all clock/reset usage if compiling for
Tegra186. This must happen at compile time rather than run-time since the
custom APIs won't even be compiled in on Tegra186. In the long term, the
plan would be to convert the existing custom APIs to standard APIs and get
rid of the ifdefs completely.
The system's main eMMC will work without any clock/reset support, since
the firmware will have already initialized the controller in order to
load U-Boot. Hence the driver is useful even in this apparently crippled
state.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra186's GPIO controller register layout is significantly different from
previous chips, so add a new driver for it. In fact, there are two
different GPIO controllers in Tegra186 that share a similar register
layout, but very different port mapping. This driver covers both.
The DT binding is already present in the Linux kernel (in linux-next via
the Tegra tree so far).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org> # v1
Signed-off-by: Tom Warren <twarren@nvidia.com>
Future chips will contain different GPIO HW. This change will enable
future SoC support to select the appropriate GPIO driver for their HW,
in a future-looking fashion, using Kconfig.
TEGRA_GPIO is not simply selected by TEGRA_COMMON (even though all
current Tegra chips used this GPIO HW) to simplify the later addition
of support for Tegra SoCs that use different GPIO HW.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add ethernet driver for the AR933x and AR934x Atheros MIPS machines.
The driver could be easily extended to other WiSoCs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Wills Wang <wills.wang@live.com>
[fixed Kconfig dependency]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
If dev->iobase is 64 bits wide then writing the value of the BAR into a
pointer to iobase will not work on big endian systems, where the BAR
value will incorrectly get written to the upper 32 bits of the 64 bit
variable. Fix this by reading the BAR into a u32, matching the type
expected by pci_read_config_dword.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fix the pcnet driver to build safely on 64 bit platforms, in preparation
for allowing MIPS64 builds for Malta boards.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Now that MIPS virt_to_phys can handle kseg1 addresses on MIPS32, stop
manually converting addresses to their kseg0 equivalents in the pcnet
driver.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
For odroid-c2 (arch-meson) for now disable designware eth as meson
now needs to do some harder GPIO work.
Signed-off-by: Tom Rini <trini@konsulko.com>
Conflicts:
lib/efi_loader/efi_disk.c
Modified:
configs/odroid-c2_defconfig
When offset is not aligned to page address, it is possible that extra offset
will be read from nand. Adjust the image such that first byte of the image
is at load address after the first page is read.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Detect a FIT when loading from SPI and handle it using the
new FIT SPL support.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This adds platform code for the Amlogic Meson GXBaby (S905) SoC and a
board definition for ODROID-C2. This initial submission only supports
UART and Ethernet (through the existing Designware driver). DTS files
are the ones submitted to Linux arm-soc for 4.7 [1].
[1] https://patchwork.ozlabs.org/patch/603583/
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
All members of the DMA descriptor must be 32-bit, even on 64-bit
architectures: change the type to u32 to ensure this. Also, fix
other warnings.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Use phys_addr_t not unsigned long long to test that we're within
DMA'able memory]
Signed-off-by: Tom Rini <trini@konsulko.com>
When these functions are not compiled in, we still need to declare the
correct function signature to avoid a build warnings in SPL. Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Setup the clocks for the gmac ethernet interface. This assumes the mac
clock is fed by an external clock which is common on RK3288 based
devices.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rgmii_pins node in rk3288.dtsi configures 15 pins. Increase the size
of the cell array to accomedate that, otherwise only the first 10 get
configured.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for the snps,reset-gpio, snps,reset-active-low (optional) and
snps,reset-delays-us device-tree bindings. The combination of these
three define how the PHY should be reset to ensure it's in a sane state.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
A DM driver for PCA953x was recently introduced by Peng Fan, which lacked
support for the 40 GPIO versions.
This patch adds support for these chips.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Peng Fan <van.freenix@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a sandbox mailbox implementation (provider), a test client
device, instantiates them both from Sandbox's DT, and adds a DM test
that excercises everything.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org> # v1
A mailbox is a hardware mechanism for transferring small message and/or
notifications between the CPU on which U-Boot runs and some other device
such as an auxilliary CPU running firmware or a hardware module.
This patch defines a standard API that connects mailbox clients to mailbox
providers (drivers). Initially, DT is the only supported method for
connecting the two.
The DT binding specification (mailbox.txt) was taken from Linux kernel
v4.5's Documentation/devicetree/bindings/mailbox/mailbox.txt.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
The current reset API implements a method to reset the entire system.
In the near future, I'd like to introduce code that implements the device
tree reset bindings; i.e. the equivalent of the Linux kernel's reset API.
This controls resets to individual HW blocks or external chips with reset
signals. It doesn't make sense to merge the two APIs into one since they
have different semantic purposes. Resolve the naming conflict by renaming
the existing reset API to sysreset instead, so the new reset API can be
called just reset.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Now that the DM core sets driver_data before calling bind(), this driver
can make use of driver_data to determine the set of child devices to
create, rather than manually re-implementing the matching logic in code.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
This will allow a driver's bind function to use the driver data. One
example is the Tegra186 GPIO driver, which instantiates child devices
for each of its GPIO ports, yet supports two different HW instances each
with a different set of ports, and identified by the udevice_id .data
field.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
If the UART is to be accessed using I/O port accessors (inb & outb) then
using map_physmem doesn't make sense, since it operates in a different
memory space. Remove the call to map_physmem when
CONFIG_SYS_NS16550_PORT_MAPPED is defined, allowing I/O port addresses
to not be mangled by the incorrect mapping.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Support ISA busses in much the same way as Linux does. This allows for
ISA bus addresses to be translated, and only if CONFIG_OF_ISA_BUS is
selected in order to avoid including the code in builds which won't need
it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The A80 uses the AXP809 as its primary PMIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Adds poweroff support for axp818 pmic.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The AXP818 has a switchable output, SW. This is commonly used for
controlling power to the LCD backlight.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Description said eldo2 instead of fldo2, a copy-paste error.
Fixes: 38491d9c65 ("power: axp818: Add support for FLDOs")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The ELDO enable bits and registers are contiguous for axp221. Instead
of a switch case testing against the index, just use the index to shift
the bit or register offset.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Now that we are using driver model, we can drop the weak functions and LCD
init in the board file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Update several boards to use driver model for video. This involves changes
to the EDP and FIMD (frame buffer) drivers. Existing PWM, simple-panel and
pwm-backlight drivers are used. These work without additional configuration
since they use the device tree settings in the same way as Linux.
Boards converted are:
- snow
- spring
- peach-pit
- peach-pi
All have been tested. Not converted:
- MIPI display driver
- s5pc210_universal
- smdk5420
- smdk5250
- trats
- trats2
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Use 'priv' for a private pointer and 'regs' for a register pointer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rename this function to better fit with driver model. It is the private data
for the exynos EDP driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This function controls enabling the EDP PHY. Rename it and drop the existing
weak functions, which are confusing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This driver supports the standard PWM API. There are 5 PWMs. Four are used
normally and the last is normally used as a timer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
At present exynos_fimd.c is the controller and exynos_fb.c is the U-Boot
LCD interface. With driver model we want these in one file, so join them
in preparation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In preparation for making this a parameter, move it into the function
that sets it up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Put the pointer to this structure in struct vidinfo so that we can
reference it without it being global.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In preparation for making this a parameter, move it into the function
that sets it up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Drop these and use parameters instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Drop these and use the existing variables instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Drop these and use parameters instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Drop this and use parameters instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Use 'struct vidinfo' instead so that we can change this to a struct with a
different name in future.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
We always use device tree with video, so can drop these #ifdefs. Some of the
hardware addresses are not needed either.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Move all the exynos video drivers into one place for ease of maintenance.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
On Exynos platforms that support clock driver API, allow the driver to
use clock api get the SCLK clock rate.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The port id, if not specified in the device node, can be obtained from
the alias of the device node listed in the aliases node.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add a clock driver for Exynos7420 SoC. There are about 25 clock controller
blocks in Exynos7420 out of which support for topc, top0 and peric1 blocks
are added in this initial version of the driver.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add pinctrl driver support for Samsung's Exynos7420 SoC. The changes
have been split into Exynos7420 specific and common Exynos specific
portions so that this implementation is reusable on other Exynos
SoCs as well.
The Exynos pinctrl driver supports only device tree based pin
configuration. The bindings used are similar to the ones used in the
linux kernel.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
It is possible to have multiple pin controllers in the system. Use the
DM_UC_FLAG_SEQ_ALIAS flag so that the pinctrl instances are assigned
a sequence number.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
When using rcw protocols to support 10G on MAC9 and MAC10, these MACs
should not be identified as 1G interface, otherwise, one MAC will be
listed as two Ethernet ports. For example, MAC9 will be listed as
FM1@TGEC1 and FM1@DTSEC9.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The code assumed that if the interface is not RGMII configured
then it must be SGMII configured. This device has the ability
to support most of the MII interfaces. Therefore add the
helper for SGMII and only configure the device if the interface is
configured for SGMII.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move the phy_interface_is_rgmii to the phy.h
file for all phy's to be able to use the API.
This now aligns with the Linux kernel based on
commit e463d88c36d42211aa72ed76d32fb8bf37820ef1
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Not all devices use the same internal delay or fifo depth.
Add the ability to set the internal delay for rx or tx and the
fifo depth via the devicetree. If the value is not set in the
devicetree then set the delay to the default.
If devicetree is not used then use the default defines within the
driver.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add the ability to pass the phy-handle node offset
to the phy driver. This allows the phy driver
to access the DT subnode's data and parse accordingly.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add the ability to read the phy-handle node of the
cpsw slave. Upon reading this handle the phy-id
can be stored based on the reg node in the DT.
The phy-handle also needs to be stored and passed
to the phy to access any phy data that is available.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Different TI platforms has to read with different combination to
get the mac address from efuse. So add support to read mac address
based on machine/device compatibles.
The code is taken from Linux drivers/net/ethernet/ti/cpsw-common.c
done by Tony Lindgren.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Since dra7x platforms address bus is define as 64 bits to support
LAPE, fdtdec_get_addr() returns a invalid address for mdio based
and gmii_sel register address. Fixing this by using
fdtdec_get_addr_size_auto_noparent() which will derive address
cell and size cell from its parent.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On some boards number of slaves can be 1 when only one port
ethernet is pinned out. So do not break when slave_index and
num slaves check fails, instead continue to parse the next
child.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Provide an api to check whether the given device or machine is
compatible with the given compat string which helps in making
decisions in drivers based on device or machine compatible.
Idea taken from Linux.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
The previous mv88e61xx driver was a driver for configuring the
switch, but did not integrate with the PHY/networking system, so
it could not be used as a PHY by U-boot. This is a complete
rework to support this device as a PHY.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
No boards are using this driver. Remove in preparation for a new
driver with integrated PHY support.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
i.MX6DQPlus support sata interface, so not return failure
when CPU is i.MX6DQPlus.
In this patch, also use simpler runtime cpu dections macros to replace
is_cpu_type.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tang Yuantian <Yuantian.Tang@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Use simpler runtime cpu dection macros.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Use simpler runtime cpu dection macros.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Scott Wood <oss@buserror.net>
The patch
"net: phy: do not read configuration register on reset"
(sha1: a058052c35)
was causing regression on zynq zc702 board where Marwell 88e1118
phy was resetted after negotiation was setup.
Phy reset is done pretty early in phy_connect_dev() and doens't need to
be called again in phy code.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Propagate error code from genphy_update_link() to phy startup().
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Add zynq_gpio_get_function() which return status on gpio pin.
This function enables gpio status command.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When the base registers are read from device tree the base is not
0x48030100 as the driver expects, but 0x48030000, resulting in
non functioning SPI. To deal with this, use same idea as how this
is done in the linux kernel (drivers/spi/spi-omap2-mcspi.c) and
add a structure with a field that is used to shift the registers
on these systems.
v2: Fixed commit subject line to correct cpu
Signed-off-by: Martin Hejnfelt <mh@newtec.dk>
Loading ACPI table from QEMU's fw_cfg interface is not x86 specific
(ARM64 may also make use of it). So move the code to common place.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Make file names consistent with CONFIG_QFW and CONFIG_CMD_QFW
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The original implementation of qfw includes several x86 specific
operations, like directly calling outb/inb and using some inline
assembly code which prevents it being ported to other architectures.
This patch adds callback functions and moves those to arch/x86/
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch splits qfw command interface and qfw core function into two
files, and introduces a new Kconfig option (CONFIG_QFW) for qfw core.
Now when qfw command interface is enabled, it will automatically select
qfw core. This patch also makes the ACPI table generation select
CONFIG_QFW.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
PIC32 internal flash devices are parallel NOR flash divided into
number of banks to allow erase-programming in one while fetch and
execution continues on other. As the flash banks are memory mapped
stored code can be executed directly from flash (XIP), also there
is additional hardware logic to prefetch and cache contents to
improve execution performance. These flash can also be used to
store user data (like environment).
Flash erase and programming are handled by on-chip NVM controller.
Driver implemented driver model but MTD is not really support.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch add a compatible spi driver for ath79 series SOC.
Signed-off-by: Wills Wang <wills.wang@live.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch add support for ar933x serial.
Signed-off-by: Wills Wang <wills.wang@live.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is a simple pinctrl driver, it just support uart and spi pin-mux now.
Signed-off-by: Wills Wang <wills.wang@live.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[fixed typo in commit subject line]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This is a simple pinctrl driver, it just support uart and spi pin-mux now.
Signed-off-by: Wills Wang <wills.wang@live.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[fixed typo in commit subject line]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
For reason unknown, recently, the DDR init code writers are really fond
of hiding some small floating point operating deep in their creations.
This patch removes one from the Marvell A38x code.
Instead of returning size of chip as float from ddr3_get_device_size()
in GiB units, return it as int in MiB units. Since this would interfere
with the huge switch code in ddr3_calc_mem_cs_size(), rework the code
to match the change.
Before this patch, the cs_mem_size variable could have these values:
( { 16, 32 } x { 8, 16 } x { 0.01, 0.5, 1, 2, 4, 8 } ) / 8 =
{ 0.000000, 0.001250, 0.002500, 0.005000, 0.062500, 0.125000,
0.250000, 0.500000, 1.000000, 2.000000, 4.000000, }
The switch code checked for a subset of the resulting RAM sizes, which
is in range 128 MiB ... 2048 MiB.
With this patch, the cs_mem_size variable can have these values:
( { 16, 32 } x { 8, 16 } x { 0, 512, 1024, 2048, 4096, 8192 } ) / 8 =
{ 0, 64, 128, 256, 512, 1024, 2048, 4096 }
To retain previous behavior, filter out 0 MiB (invalid size), 64 MiB
and 4096 MiB options.
Removing the floating point stuff also saves 1.5k from text segment:
clearfog : spl/u-boot-spl:all -1592 spl/u-boot-spl:text -1592
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
During DDR-2133 operation, the transmit data eye margins determined
during the memory controller initialization may be sub-optimal, set
DEBUG_29[12] and DEBUG_29[13:16] = 4'b0100 before MEM_EN is set.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For SoCs that contain multiple SEC engines, each of them needs
to be initialized (by means of initializing among others the
random number generator).
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The S25FS-S family physical sectors may be configured as a hybrid
combination of eight 4-kB parameter sectors at the top or bottom
of the address space with all but one of the remaining sectors
being uniform size.
The default status of the flash is in this hybrid architecture.
The parameter sectors and the uniform sectors have different erase
commands.
This patch disable the hybrid sector architecture then the flash will
has uniform sector size and uniform erase command.
This configuration is temporary, the flash will revert to hybrid
architecture after power on reset.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The flash type of LS2085AQDS QSPI is S25FS256S. It has special write
any device register command and read any device register command.
This patch enable support for those commands.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QSPI controller automatic enable the chipselect signal according the
dest AMBA memory address. Now we distribute the AMBA memory zone
averagely to every chipselect slave device according chipselect
numbers got from dts node.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The address value and size value get from dts "reg" property have
type of u64 on arm64. If we assign those values to "u32" variables,
driver can't work correctly. Converting the type of those variables
to fdt_xxx_t.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The initial training for the DDRC may provide results that are not
optimized. The workaround provides better read timing margins.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Per the latest erratum document, update step 4 and step 8, only
DEBUG_29[21] is changed, all other bits should not be changed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add an emulation of an SD card to sandbox, allowing MMC to be used in tests.
The emulation is very simple, supporting only card detection and reading
test data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for enabling CONFIG_BLK with MMC. This involves changing a
few functions to use struct udevice and adding a MMC block device driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Binding an MMC device when CONFIG_BLK is enabled requires that a block
device be bound as a child of the MMC device. Add a function to do this.
The mmc_create() method will be used only when DM_BLK is disabled.
Add an unbind method also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Implement the functions in mmc_legacy.c for driver-model block devices, so
that MMC can use driver model for these. This allows CONFIG_BLK to be enabled
with DM_MMC.
Signed-off-by: Simon Glass <sjg@chromium.org>
This driver will require generic MMC and block-device support in a future
commit. To avoid test errors, make this change now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Instead of looking up the MMC device by number, just pass it in. This makes
it possible to use this function with driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the MMC subsystem maintains its own list of MMC devices. This
cannot work with driver model, which needs to maintain this itself. Move the
list code into a separate 'legacy' file. The core MMC code remains, and will
be shared with the driver-model implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
The block device uclass does not currently support selecting a particular
hardware partition but this is needed for MMC. Add it so that the blk API
can support MMC properly.
Signed-off-by: Simon Glass <sjg@chromium.org>
The MMC block device is contained within struct mmc. But with driver model
this will not be the case. Add a function to obtain the block device. We
can later implement this for CONFIG_BLK.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is defined after it is used. In preparation for making it
static, move it up a little. Also drop the printf() which should not appear
in a driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some devices have a name that is stored in allocated memory. At present
there is no mechanism to free this memory when the device is unbound.
Add a device flag to track whether a name is allocated and a function to
add the flag. Free the memory when the device is unbound.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function that automatically builds the device name given the parent
and a supplied string. Most callers will want to do this, so putting this
functionality in one place makes more sense.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow a devnum parameter of -1 to indicate that the device number should be
alocated automatically. The next highest available device number for that
interface type is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
