Due to dependencies between timer and CPU frequency, only changes by
powers of two are allowed. The clocksource driver prevents other
changes, but with cpufreq and its governors it can result in being
spammed with error messages constantly. Hence, remove the 222 MHz OPP.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Zynq UART is Cadence IP and the driver has been renamed accordingly.
Migrate the DT to use the new binding for the UART driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
To silence the warning
cpufreq_cpu0: failed to get cpu0 regulator: -19
from the cpufreq driver regarding a missing regulator,
add a fixed regulator to the DT.
Zynq does not support voltage scaling and the CPU rail should always be
supplied with 1 V, hence it is added in the SOC-level dtsi.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Pass directly boot_addr which is LOVEC (0) or HIVEC (0xffff0000).
No reason to use magic values 0 and 1.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define a new config "zynqmp_ep" for ZynqMP instead
of xilinx_zynqmp. This defconfig supports all emulation
platforms of ZynqMP. Also renamed TARGET_XILINX_ZYNQMP
to ARCH_ZYNQMP.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move the zynqmp Kconfig from board to arch
as there may be different boards under same
architecture.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The encoding of the sub instruction used to handle CONFIG_SYS_MALLOC_F_LEN
can only accept certain values, and the set of acceptable values differs
between the AArch32 and AArch64 instructions sets. The default value of
CONFIG_SYS_MALLOC_F_LEN works with either ISA. Tegra uses a non-default
value that can only be encoded in the AArch32 ISA. Fix the AArch64 crt0
assembly so it can handle completely arbitrary values.
Signed-off-by: Thierry Reding <treding@nvidia.com>
[twarren: trimmed Thierry's patch to remove changes already present]
Signed-off-by: Tom Warren <twarren@nvidia.com>
[swarren, cleaned up patch, wrote description, re-wrote subject]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
[swarren, stripped out changes not strictly related to warnings]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
While most stm32f4 run at 168 MHz, stm32f429 can work till 180 MHz.
Add option to select 180 MHz through macro CONFIG_SYS_CLK_FREQ.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: Albert Aribaud <albert.u.boot@aribaud.net>
To: Tom Rini <trini@konsulko.com>
To: Kamil Lulko <rev13@wp.pl>
Cc: u-boot@lists.denx.de
Read device unique ID and set environment variable "serial#".
Value would then be passed to kernel through DTB.
To read ID from DTB, kernel is required to have commit:
3f599875e5202986b350618a617527ab441bf206 (ARM: 8355/1: arch: Show
the serial number from devicetree in cpuinfo)
This commit is already mainline since v4.1-rc1.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: Albert Aribaud <albert.u.boot@aribaud.net>
To: Tom Rini <trini@konsulko.com>
To: Kamil Lulko <rev13@wp.pl>
Cc: u-boot@lists.denx.de
Because the top-level Makefile forces all the source files
to include include/linux/kconfig.h (see the UBOOTINCLUDE define),
these includes are redundant.
By the way, there are exceptions for the statement above; host
programs. In fact, host tools in U-Boot depend on a particular
board configuration, although I think they should not. So, some
files still include <linux/config.h> to work around build errors
on host tools.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Simon Glass <sjg@chromium.org>
All am33xx device tree are using device-tree, so get_board_rev is never actually
called. Thus, we can get rid of it to make the code easier to maintain.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
Despite being defined with __weak, this declaration of get_board_rev will
conflict with the fallback one when ONFIG_REVISION_TAG is not defined.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces code to read the value of the SYS_BOOT pins on the OMAP5, as
well as the memory-preferred scheme for the interpretation of each value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This introduces code to read the value of the SYS_BOOT pins on the OMAP4, as
well as the memory-preferred scheme for the interpretation of each value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This introduces code to read the value of the SYS_BOOT pins on the OMAP3, as
well as the memory-preferred scheme for the interpretation of each value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
OMAP devices might boot from peripheral devices, such as UART or USB.
When that happens, the U-Boot SPL tries to boot the next stage (complete U-Boot)
from that peripheral device, but in most cases, this is not a valid boot device.
This introduces a fallback option that reads the SYS_BOOT pins, that are used by
the bootrom to determine which device to boot from. It is intended for the
SYS_BOOT value to be interpreted in the memory-preferred scheme, so that the
U-Boot SPL can load the next stage from a valid location.
Practically, this options allows loading the U-Boot SPL through USB and have it
load the next stage according to the memory device selected by SYS_BOOT instead
of stalling.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Now that SPL boot devices are clearly defined, we can use BOOT_DEVICE_QSPI_4
instead of a hardcoded value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This cleans up the SPL boot devices for omap platforms and introduces support
for missing boot devices.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This introduces OMAP3 support for the common omap boot code, as well as a
major cleanup of the common omap boot code.
First, the omap_boot_parameters structure becomes platform-specific, since its
definition differs a bit across omap platforms. The offsets are removed as well
since it is U-Boot's coding style to use structures for mapping such kind of
data (in the sense that it is similar to registers). It is correct to assume
that romcode structure encoding is the same as U-Boot, given the description
of these structures in the TRMs.
The original address provided by the bootrom is passed to the U-Boot binary
instead of a duplicate of the structure stored in global data. This allows to
have only the relevant (boot device and mode) information stored in global data.
It is also expected that the address where the bootrom stores that information
is not overridden by the U-Boot SPL or U-Boot.
The save_omap_boot_params is expected to handle all special cases where the data
provided by the bootrom cannot be used as-is, so that spl_boot_device and
spl_boot_mode only return the data from global data.
All of this is only relevant when the U-Boot SPL is used. In cases it is not,
save_boot_params should fallback to its weak (or board-specific) definition.
save_omap_boot_params should not be called in that context either.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
When core A turning of core B, via tetris DPSC it places the core
B DPSC into transitional state. The core B has to execute wfi instruction
to move its DPSC to the OFF state. This patch add such instruction.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This allows using devices plugged into both ports of the tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
On some boards the otg is wired up in host-only mode in this case we
have no vbus-det gpio.
Stop logging an error from sunxi_usb_phy_vbus_detect() in this case, and
stop treating sunxi_usb_phy_vbus_detect() returning a negative errno, as
if a charger is plugged into the otg port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Modify the sunxi musb glue to use the device-model for musb host mode.
This allows using musb in host mode together with other host drivers
such as ehci / ohci, which is esp. useful on boards which use the
musb controller in host-only mode, these boards have e.g. an usb-a
receptacle or an usb to sata converter attached to the musb controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Move the musb config and platdata to the sunxi-musb glue, which is where
it really belongs. This is preparation patch for adding device-model
support for the sunxi-musb-host code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for reading the id pin value of the otg connector to the usb
phy code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Start using the new Kconfig options which are available for these now,
and simply always enable them by selecting them as sunxi builds always
include USB support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
With certain features being convert to DM now we want sunxi to default
to having DM enabled for ETH/SERIAL and USB in some cases.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Tom Rini <trini@konsulko.com>
[hdegoede@redhat.com: Also select CONFIG_USB for all sunxi builds]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
At one point in time the utoo-p66 dts file in the kernel had a bogus
uart entry, and it seems like we synced with the kernel at just the wrong
moment.
This commit removes the bogus uart entry, which breaks booting the utoo-p66
when DM_SERIAL=y.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Make possible using a single `u-boot-sunxi-with-spl.bin` binary for both NAND
memory and SD card. Detection where SPL was read from is implemented in
`spl_boot_device`.
Signed-off-by: Daniel Kochmański <dkochmanski@turtle-solutions.eu>
CC: Roy Spliet <r.spliet@ultimaker.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
[hdegoede@redhat.com: Some small coding style fixes]
Acked-by: Hans De Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch extracts checking for valid SD card "eGON.BT0" signature from
`board_mmc_init` into function `sunxi_mmc_has_egon_boot_signature`.
Buffer for mmc sector is allocated and freed at runtime. `panic` is
triggered on malloc failure.
Signed-off-by: Daniel Kochmański <dkochmanski@turtle-solutions.eu>
CC: Roy Spliet <r.spliet@ultimaker.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
[hdegoede@redhat.com: Small bugfix to make it work for devs other then mmc0]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch adds basic SDIO/MMC booting support to MVEBU SoC's. Since
I don't know of a way to test the boot-device upon runtime, this patch
hardcodes the spl_boot_device instead.
Tested on Marvell DB-88F6820-GP board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <eibach@gdsys.de>
The init code for UMC (Unified Memory Controller) and PLL has not
been mainlined yet, but U-boot proper should work.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
For the record, describe exactly which device of which vendor
is used on this board.
I2C EEPROM is bound by the generic compatible string, "i2c-eeprom",
so this commit has no impact on the functionality.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
With the upcoming addition of the Armada 38x DDR support, which is not
compatible to the Armada XP DDR init code, we need to introduce a new
directory infrastructure. To support multiple Marvell DDR controller.
This will be the new structure:
drivers/ddr/marvell/axp
Supporting Armada XP (AXP) devices (and perhaps Armada 370)
drivers/ddr/marvell/a38x
Supporting Armada 38x devices (and perhaps Armada 39x)
Signed-off-by: Stefan Roese <sr@denx.de>
This code is ported from the Marvell bin_hdr code into mainline
SPL U-Boot. It needs to be executed very early so that the devices
connected to the serdes PHY are configured correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
With the upcoming addition of the Armada 38x SPL support, which is not
compatible to the Armada XP SERDES init code, we need to introduce a new
directory infrastructure. So lets move the AXP serdes init code into
a new directory. This way the A38x code can be added in a clean way.
Signed-off-by: Stefan Roese <sr@denx.de>
Only with disabled MMU its possible to switch the base register address on
Armada 38x. Without this the SDRAM located at >= 0x4000.0000 is also not
accessible, as its still locked to cache.
Signed-off-by: Stefan Roese <sr@denx.de>
Pin muxing needs to be done before UART output, since on A38x the UART
pins need some re-muxing for output to work.
Signed-off-by: Stefan Roese <sr@denx.de>
On A38x switching the regs base address without running from
SDRAM doesn't seem to work. So let the SPL still use the
default base address and switch to the new address in the
mail u-boot later.
Signed-off-by: Stefan Roese <sr@denx.de>
Without calling timer_init(), the xdelay() functions return immediately.
We need to call timer_init() early, so that these functions work and
the PHY and DDR init code works correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anton Schubert <anton.schubert@gmx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch initializes the SATA address windows on Armada XP and
allows it to work with the existing mvsata_ide driver.
It also adds the necessary configuration for the db-mv784mp-gp board.
Signed-off-by: Anton Schubert <anton.schubert@gmx.de>
Tested-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Add the required files for the Broadcom UDC OTG interface.
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
USB download gadget functions such as thor and dfu have a separate config option
for the USB gadget part of the code, independent from the command part.
This switches the fastboot USB gadget to the same scheme, for better
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
Move USB controller Base address mapping from ls102xa immap
to fsl xhci header. This is required to remove any warnings when
controller base addresses are mapped for multiple platforms
in their respective files.
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Since we want clk_ops to be used in U-Boot as a whole, rename the Zynq
version until it can be converted to driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Driver-model I2C drivers can be picked up by the linker script rule for
legacy drivers. Change the order to avoid this.
We could make the legacy code depend on !CONFIG_DM_I2C but that is not
necessary and it is good to keep conditions to a minimum.
Signed-off-by: Simon Glass <sjg@chromium.org>
The SPL device tree size must be minimised to save memory. Only include
properties that are needed by SPL - this is determined by the presence
of the "u-boot,dm-pre-reloc" property. Also remove a predefined list of
unused properties from the nodes that remain.
Signed-off-by: Simon Glass <sjg@chromium.org>
When final MMU table is setup in DDR, TCR attributes must match
those of the memroy for cacheability and shareability.
Signed-off-by: Zhichun Hua <zhichun.hua@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
For ARMv8, outer shareable is 0b10, inner shareable is 0b11 at bit
position [13:12] of TCR_ELx register.
Signed-off-by: Zhichun Hua <zhichun.hua@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
DSPI has pin muxing with SDHC and other IPs, this patch check the
value of RCW SPI_PCS_BASE and SPI_BASE_BASE fields, it also check
the "hwconfig" variable. If those pins are configured to DSPI and
"hwconfig" enable DSPI, set the BRDCFG5 of QIXIS FPGA to configure
the routing to on-board SPI memory. Otherwise will configure to SDHC.
DSPI is enabled in "hwconfig" by appending "dspi", eg.
setenv hwconfig "$hwconfig;dspi"
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add dts source files for LS2085AQDS and LS2085ARDB boards.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Bring in required device tree files for ls2085a from Linux. These are
initially unchanged and have a number of pieces not needed by U-Boot.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As SCFG_ENDIANCR register is added to choose little-endian or big-endian
for audio IPs on Rev2.0 silion, little-endian mode is selected.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Base on PSCI services, implement CPU_ON/CPU_OFF for ls102xa platform.
Tested on LS1021AQDS, LS1021ATWR.
Test CPU hotplug times: 60K
Test kernel boot times: 1.2K
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
timer_wait is moved from sunxi/psci_sun7i.S, and it can be converted
completely into a reusable armv7 generic timer. LS1021A will use it
as well.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As the function 'sprintf' does not check buffer boundaries but outputs
to the buffer 'enet' of fixed size (16), this patch removes the function
'sprintf', and uses 'strcpy' instead. It will assign the character
arrays 'enet' and 'phy' the corresponding character strings.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds the infrastructure to update device
tree nodes to convey SMMU stream IDs in the device
tree. Fixups are implemented for PCI controllers
initially.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Stream IDs on ls2085a devices are not hardwired and are
programmed by sw. There are a limited number of stream IDs
available, and the partitioning of them is scenario dependent.
This header defines the partitioning between legacy, PCI,
and DPAA2 devices.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch updates the setting of required bits for A57 cores erratas
- 828024 and 826974
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Dai Haruki <dai.haruki at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Update SoC README to provide details of
- Memory regions
- Memory used by MC and Debug server
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds support to print out the SoC personality.
Freescale LS20xx SoCs (compliant to Chassis-3 specifications) can
have 6 personalities: LS2045AE, LS2045A, LS2080AE, LS2080A,
LS2085AE and LS2085A
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
DDR speed should be in MT/s, not MHz.
Signed-off-by: York Sun <yorksun at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
call ft_pci_setup() to disable PCIe dts node if corresponding
PCIe controller is disabled according to RCW
Signed-off-by: Minghuan Lian <Minghuan.Lian at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds USB EHCI host support for the common mvebu platform.
Including the Armada 38x.
Tested on DB-88F6280-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds support for the common AHCI controller on the Marvell
Armada 38x.
Tested on the Marvell DB-88F6820-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Armada A38x implements an SDHCI compatible SDIO controller. This patch
enables the Marvell driver to support this SoC. And enables the
SDIO controller if selected by the board configuration.
Tested on Marvell DB-88F6820-GP board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Add support in mxc_i2c driver, iomux_v3 and vf610 architecture for the four
I2C instances available in VF610.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
hab_status command returns a memory dump of the hab event log. But the
raw data is not human-readable. Parsing such data into readable event
will help to minimize debbuging time.
Signed-off-by: Ulises Cardenas <Ulises.Cardenas@freescale.com>
Add I2C4 clock support for i.MX6SX. Since we use runtime check,
but not macro, we need to remove `#ifdef ..` in crm_regs.h, or
gcc will fail to compile the code succesfully.
Making the macros only for i.MX6SX open to other i.MX6x maybe not
a good choice, but we have runtime check.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
enable_spi_clock does the same thing with enable_cspi_clock, so
remove enable_cspi_clock.
Remove enable_cspi_clock prototype in header file
convert cm_fx6/spl.c to use enable_spi_clk
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
sun8i-a33-ippo-q8h-v1.2-lcd1024x600.dts has been merged into the upstream
Linux kernel as sun8i-a33-ippo-q8h-v1.2.dts, adjust u-boot to follow.
Note we've never shipped a final u-boot version with the old name, so this
is safe todo.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The root cause of this problem should now be fixed.
This reverts commit a6a4c542d3.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Pavel Machek <pavel@denx.de>
Tested-by: Pavel Machek <pavel@denx.de>
When CONFIG_SYS_THUMB_BUILD is defined these functions may be called from
Thumb code. Add the required ENTRY and ENDPROC bracketing so that BLX is
used to call these ARM functions, instead of plain BL, which will fail.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Pavel Machek <pavel@denx.de>
Sinlinx SinA33 is a core/daughter board SDK kit from Sinlinx. It has
the A33 SoC, USB host, USB OTG, audio input/output, LCD, camera, SDIO
and GPIO headers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Copy over all the latest dts changes from mripard/sunxi/dt-for-4.2.
This adds a dts file for Sinlinx SinA33 dev board, and the required
changes in the .dtsi files.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The A33 adds a pinmux function for UART0 in the PB pin group.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The original code was configuring the external pins after enabling
the R_PIO clock, which meant the configuration never made it to
the pin controller the first time in SPL.
Why this was working before is uncertain. Maybe the state was left
from a previous boot sequence, or RSB just happened to be the default
configuration. However with some A33 chips, SPL failed to configure
the PMIC. This was seen by me and Maxime on the Sinlinx SinA33 dev
board.
Reordering the calls fixed this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Commit 487b327 ("sunxi: GPIO pin mux hardware-feature-specific function
index defines") renamed all GPIO index defines, but missed the PORT F
UART0 setup functions.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch adds the device tree binding doc for the cadence qspi controller &
also removes the not needed properties from the stv0991 device tree.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
sram size could be different on different socs, e.g. on stv0991 it is 256 while
on altera platform it is 128. It is better to receive it from device tree.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
This patch add the device tree entry for qspi controller & spi flash
memory.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
This patch does all the board configurations required to use the qspi
controller & attached spi flash memory.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
stv0991 has cadence qspi controller for flash interfacing, this
patch configures the device pads & clock for the controller.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
The current GPL only licensing on the device trees makes it very
impractical for other software components licensed under another
license.
To make it easier to reuse them, the device trees for UniPhier
SoCs and boards have already been dual-licensed in Linux.
Follow this trend in U-boot too.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This makes code diff much easier.
Device trees describe hardware attributes, which are independent
of software architecture. It generally makes sense to synchronize
them beyond software projects.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now zynq spi driver platform data is controlled by devicetree,
enable the status by saying "okay" on respective board dts to use
the devicetree generated platdata.
Ex:
&spi1 {
status = "okay";
};
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Enabled CONFIG_DM_SPI and CONFIG_DM_SPI_FLASH for zynq soc.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>
The type of DSPI flash on ls1021aqds is AT45DB021, it has specail
commands and page-size.
Use the special spi flash driver instead of "spi_flash_std" driver.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This reverts commit f76eba38b3.
This patch did not have a full and proper copyright/S-o-b chain.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Conflicts:
include/configs/sun6i.h
include/configs/sun8i.h
Add a new revision CHIP_REV_2_0.
Introudce macro is_mx6dqp, dqp means Dual/Quad Plus.
Since Dual/Quad Plus use same cpu type with Dual/Quad, but different
revision(Major Lower), we use this macro for Dual/Quad Plus.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
The DIGPROG register map:
23 ------- 16 | 15 ------ 8 | 7 --- 0 |
Major upper | Major Lower | Minor |
We also need to account for Major Lower.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
is_soc_rev should return a bool value, so use "==", but not "-",
change (is_soc_rev(CHIP_REV_1_0) > 0) to (soc_rev() > CHIP_REV_1_0).
This patch also add space between "&" for cpu_type(rev) macro.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
This is the first patch to remove the
CONFIG_SYS_EXTRA_OPTIONS.
This patch implements CPU type selection from Kconfig.
Further Kconfig stuff is added later.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.
Remove the configs that behave this way from the archs.
A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:
SPIFLASH
DISPLAY_BOARDINFO
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: Tom Rini <trini@konsulko.com>
Update new naming scheme.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
rastaban is a draco version with more flash, more RAM
and faster CPU. Number of partitions is the same but
rootfs partition is different.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
DRA7/AM57xx devices can be operated in many different configurations.
When the SoC is supposed to support a configuration where low power mode
state may involve the SoC completely powered off and DDR is in self
refresh, SoC EMIF controller should not be the master of the reset
signal and an external entity might be in control of things.
The default configuration of Linux on TI evms involve not powering off
the voltage rails (due to various reasons including reliability concerns)
and must not allow DDR reset to be controlled by EMIF. On platforms
where external entity might control the reset signal, this configuration
will be a "dont care".
Fixes: 536d874708 ("ARM: DRA7: Update DDR IO registers")
Tested-by: Keerthy <j-keerthy@ti.com>
Acked-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The get_max_arm_speed() and get_max_dev_speed() used wrong register
fields to get the maximum speeds. This commit fixes the bug.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently on sun6i after a "reset" the prompt returns and the user can
even type stuff until the watchdog triggers and does the actual reset.
This is somewhat unexpected behavior for the "reset" command, this
commit adds an endless loop to wait for the watchdog to trigger so that
we do not return to the prompt.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Vision Systems's Baltos is based on AM335x SoC
from Texas Instruments. This patch adds support
such Industrial PCs in mainline u-boot.
[ balbi@ti.com: updated original patch to current u-boot ]
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Unlike OMAP5, EMIF PHY used in DRA7 will be left in unknown state after
warm reset, emif needs to be configured to bring it back to a known
state. So configure EMIF during warm reset.
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The recent changes for hw leveling on am33xx were not intended for
DDR2 boards, only DDR3. Update emif_sdram_type to take a sdram_config
value to check against. This lets us pass in the value we would use to
configure, when we have not yet configured the board yet. In other cases
update the call to be as functional as before and check an already
programmed value in.
Tested-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
On AM57xx evm I2C5 is used to detect the LCD board by reading the
EEPROM present on the bus.
Enable i2c5 clocks to help that.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
SMP-enabled Linux kernels read the CBAR register in CP15 to find
the address of the SCU registers. After remapping internal
registers, also update the CBAR so the kernel can find them.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
L2 cache may still be enabled by the BootROM. We need to first disable
it before enabling d-cache support.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Now all manual mode configurations are done as part of
IO delay recalibration sequence, remove the hack done for
CPSW.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In addition to the regular mux configuration, certain pins of DRA7
require to have "manual mode" also programmed, when predefined
delay characteristics cannot be used for the interface.
struct iodelay_cfg_entry is introduced for populating
manual mode IO timings.
For configuring manual mode, along with the normal pad
configuration do the following steps:
- Select MODESELECT field of each assocaited PAD.
CTRL_CORE_PAD_XXX[8]:MODESELECT = 1(Enable MANUAL_MODE macro along with mux)
- Populate A_DELAY, G_DELAY values that are specified in DATA MANUAL.
And pass the offset of the CFG_XXX register in iodelay_cfg_entry.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
On DRA7, in addition to the regular muxing of pins, an additional
hardware module called IODelay which is also expected to be
configured. This "IODelay" module has it's own register space that is
independent of the control module.
It is advocated strongly in TI's official documentation considering
the existing design of the DRA7 family of processors during mux or
IODelay recalibration, there is a potential for a significant glitch
which may cause functional impairment to certain hardware. It is
hence recommended to do muxing as part of IOdelay recalibration.
IODELAY recalibration sequence:
- Complete AVS voltage change on VDD_CORE_L
- Unlock IODLAY config registers.
- Perform IO delay calibration with predefined values.
- Isolate all the IOs
- Update the delay mechanism for each IO with new calibrated values.
- Configure PAD configuration registers
- De-isolate all the IOs.
- Relock IODELAY config registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
In addition to the regular mux configuration, certain pins of DRA7
require to have "virtual mode" also programmed.
This allows for predefined delay characteristics to be used by the SoC
to meet timing characterstics needed for the interface.
Provide easy to use macro to do the same.
For configuring virtual mode, along with normal pad configuration add
the following two steps:
- Select MODESELECT field of each assocaited PAD.
CTRL_CORE_PAD_XXX[8]:MODESELECT = 1
- DELAYMODE filed should be configured with value given in DATA Manual.
CTRL_CORE_PAD_XXX[7:4]:DELAYMODE =[0-15] (as given in DATA manual).
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Adopting the pinctrl register definitions from Linux kernel
to be consistent.
Old definitions will be removed once all the pinctrl data
is adapted to new definitions.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
do_set_mux32() is redefined in dra7xx and beagle_x15 boards.
IO delay recalibration sequence also needs this.
Making it generic to avoid duplication.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
When DLL_CALIB_INTERVAL is set, an extra delay is added
which is not required and it consumes EMIF bandwidth.
So making the DLL_CALIB_CTRL[8:0]DLL_CALIB_INTERVAL bits to 0.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
DDRIO_2 and LPDDR2CH1_1 registers are not present
for DRA7. So not configuring these registers for DRA7xx
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
A generic is_dra72x cpu check is useful for grouping
all the revisions under that. This is used in the
subsequent patches.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Updating EMIF registers to enable HW leveling
on DRA72-evm.
Also updating the timing registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
DRA7 EMIF supports Full leveling for DDR3.
Adding support for the Full leveling sequence.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>