Kconfig defaults to mode 3 if CONFIG_SF_DEFAULT_MODE is not set.
It becomes an issue since meson_spifc does not support SPI_CPHA.
Needed after commit e2e95e5e25 ("spi: Update speed/mode on change").
Fixes: e2e95e5e25 ("spi: Update speed/mode on change")
Signed-off-by:Da Xue <da@libre.computer>
[narmstrong: reformated commit reference & added Fixes tag]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Chapter 23 of the EFI spec (rev 2.9) says:
"A specific updatable hardware firmware store must be represented by
exactly one FMP instance".
This is not the case for us, since both of our FMP protocols can be
installed at the same time because they are controlled by a single
'dfu_alt_info' env variable.
So make the config options depend on each other and allow the user to
install one of them at any given time. If we fix the meta-data provided
by the 'dfu_alt_info' in the future, to hint about the capsule type
(fit or raw) we can revise this and enable both FMPs to be installed, as
long as they target different firmware hardware stores
Note that we are not using a Kconfig 'choice' on purpose, since we
want to allow both of those to be installed and tested in sandbox
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
imx8mm ekv has been switched to use distro boot commands, but had no
correct options enabled to support sysboot.
According to the README.distro, sysboot is consindered to be a
recommended way of using distro boot commands, it required default distro
features to be enabled instead of only those that are relevant to the boot
script.
Replace the boot script specific options in the config to a default distro
option.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Fixes: 2df8930bf9 ("imx8mm: configs: add support for distro boot commands")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
imx8mp ekv has been switched to use distro boot commands, but had no
correct options enabled to support sysboot.
According to the README.distro, sysboot is consindered to be a
recommended way of using distro boot commands, it required default distro
features to be enabled instead of only those that are relevant to the boot
script.
Replace the boot script specific options in the config to a default distro
option.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Fixes: 9b162b1d1f ("imx8mp: configs: add support for distro boot commands")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Under DM, we rely on u-boot's device tree to provide the correct PHY
addresses. The board_fix_fdt callback is intended to be used for
device tree fixups before relocation. Unfortunately, this isn't an
option when booting from flash since the device tree isn't writable
before relocation.
This patch introduces the CONFIG_T2080RDB_REV_D option to signal that a
board revision D or up is the target. The config option is used to set
the correct Aquantia PHY address in the board's u-boot device tree.
Defconfig files with the option enable explicitly are added for
convenience.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The EXPU1 design is a new 40G capable ethernet service unit card for
Hitachi-Powergrids wired-com product lines.
The base SoC is same as for already added SELI8 card, consequently the
already added u-boot support for SELI8 is reused.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
[Fixed new line error at EOF]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
During the mainlining of the board this was by mistake set to sector size.
Our user space env scripts are expecting envsize of 0x4000, and setting
this differently will break our cross-platform compatibility.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
IFC NOR flash base address of ls2088a is 0x580000000,
and offset of env crc is 0x500000, so fix the macro
CONFIG_ENV_ADDR to fix synchronous exception(access illegal address)
Fixes: 59071804c1 ("configs: ls2080a: Correct ENV_ADDR value")
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Sata/scsi and usb based devices are not started at this stage that's why
disks are not found and early update can't happen.
It is because of deficiency in the UEFI implementation which is not able to
deal with block devices which are added or removed after initialization.
EFI capsule on disk early feature needs to be fixed first to be able to
enable this feature properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable configuration options to support Turris network boot. This
includes FIT support and some crypto commands.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add necessary config options and board code to support board factory
reset / rescue mode on Turris MOX.
In order to also support invoking rescue mode from U-Boot console,
without having to press the factory reset button, put the rescue command
into `bootcmd_rescue` default environment variable. When factory reset
button is pressed, invoke rescue mode via distroboot by setting
`boot_targets` to `rescue`.
Rescue boot from console can be invoked by running
run bootcmd_rescue
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add support for Storopack's SMEGW01 board, which is an
IoT gateway based on the i.MX7D SoC.
Based on the original U-Boot work done by Phytec.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Supported boot device types in iMX8MN: MMC, DHCP.
Add DISTRO_DEFAULTS config option and include the distro boot command
header file to enable full support of distro boot on i.MX8M Nano EVK (both
DDR and LPDDR derivatives).
Drop previous environment, which was targeting customized boot commands and
boot order.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable driver model support for FEC ethernet which allows us to remove
the iomux and board_eth_init function. Replace the toggling of the ethernet
phy reset with dt configuration.
Enable driver model support for PCI which allows us to remove the
eth1000_initialize() call. Additionally enable PCI_INIT_R to scan for
PCI devices on init such as the e1000 that is present on the GW552x.
Convert board_pci_fixup to use dm callback and remove pcidisable env
variable which is not supported for DM_PCI and thus leave PCI always
enabled during init.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
A simple prototyping board with one microSD port, one Ethernet port,
2 USB ports, I2C, SPI, GPIO, and UART interfaces.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Stefano Babic <sbabic@denx.de>
Board designed for quick prototyping and has one microSD port,
2 Ethernet ports, 2 USB ports, I2C, SPI, CAN, RS-485, GPIO,
UART interfaces, and 2 RGB LEDs.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Stefano Babic <sbabic@denx.de>
These boards were not converted to DM_VIDEO before deadline,
so disable video support for now.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Richard Hu <richard.hu@technexion.com>
Cc: Fabio Estevam <festevam@gmail.com>
The board was not converted to DM_VIDEO before deadline, so disable
video support for now.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
The board was not converted to DM_VIDEO before deadline, so disable
video support for now.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Add defconfig and board support for HiFive Unmatched.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The CMD_UNZIP provides the 'gzwrite' command, which is convenient
for writing e.g. gz-compressed images to eMMC from U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The CMD_UNZIP provides the 'gzwrite' command, which is convenient
for writing e.g. gz-compressed images to eMMC from U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
AM64x GP and SK EVM have DP83867 PHY connected to CPSW external port0.
Enable the driver in order to use ethernet at U-Boot prompt.
CONFIG_PHY_TI is selected by CONFIG_PHY_TI_DP83867 and thus can be dropped.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Remove qemu_mips boards because DM migration doesn't make sense.
The board support for qemu_mips is already marked as deprecated
in Qemu in favour of the Malta board. Also qemu_mips support
has been removed from Linux a long time ago.
The official replacement is the Malta board. The same Malta U-Boot
image can be used with Qemu and on physical hardware.
All combinations of Big Endian and Little Endian as well as 32 bit
and 64 bit are supported.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch makes the necessary adjustments in the defconfig to fully
support the CFI flash on the Octeon EBB7304.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Enable LTO for some boards that were tested by people on U-Boot Mailing
List.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Adam Ford <aford173@gmail.com>
Tested-by: Pali Rohár <pali@kernel.org>
Tested-by: Tim Harvey <tharvey@gateworks.com>
It will need larger heap size for u-boot-spl to load u-boot.itb which
be generated from binman than USE_SPL_FIT_GENERATOR.
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that we have switched to binman to generate u-boot.itb for all
RISC-V boards, USE_SPL_FIT_GENERATOR is no longer needed and can
be dropped.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
