Enable the RPC Hyperflash driver on R8A7795,R8A7796,R8A77965
Salvator-X,ULCB and R8A77990 Ebisu. Note that to make the HF
accessible, mainline ATF is mandatory and must be built with
RCAR_RPC_HYPERFLASH_LOCKED=0 . Note that this is intended for
development and testing convenience only and must be disabled
in deployment for platform security reasons.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
- Enhance the 'zboot' command to be more like 'bootm' with sub-commands
- The last series of ACPI core changes for programmatic generation of
ACPI tables
- Add all required ACPI tables for ApolloLake and enable ACPIGEN on
Chromebook Coral
- A feature minor enhancements to the 'hob' command
- Intel edison: Support for writing an xFSTK image via binman
At present the 'bdinfo' command shows the framebuffer address, but not the
address of the copy framebuffer, if present. Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present linux/bitops.h is included in ACPI code. This is not needed and
can cause a problem in fls64.h since BITS_PER_LONG is not defined. Move
the #include into the part not used by ACPI.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
A few fields have an open-coded length. Use the defines for this purpose
instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This provides information about a v1 TPM in the system. Generate this
table if the TPM is present.
Add a required new bloblist type and correct the header order of one
header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for generating various ACPI tables for Apollo Lake. Add a few
S3 definitions that are needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow this header to be included in ASL files by adding a header guard and
a few definitions that are needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Apollo Lake needs to generate a few more table types used on Intel SoCs.
Add support for these into the x86 ACPI code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an implementation of the DBG2 (Debug Port Table 2) ACPI table.
Adjust one of the header includes to be in the correct order, before
adding more.
Note that the DBG2 table is generic but the PCI UART is x86-specific at
present since it assumes an ns16550 UART. It can be generalised later
if necessary.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an implementation of the HPET (High Precision Event Timer) ACPI
table. Since this is x86-specific, put it in an x86-specific file
Signed-off-by: Simon Glass <sjg@chromium.org>
Add SCI and power-state definitions required by ACPI tables. Fix the
license to match the original source file.
Als update the guard on acpi_pmc.h to avoid an error when buiding ASL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Many I2C devices produce roughly the same ACPI data with just things like
the GPIO/interrupt information being different.
This can be handled by a generic driver along with some information in the
device tree.
Add a generic i2c driver for this purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add a function to generate ACPI code for a _DSM method for a device.
This includes functions for starting and ending each part of the _DSM.
Signed-off-by: Simon Glass <sjg@chromium.org>
[bmeng: fix the "new blank line at EOF" git warning]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
A 'Power Resource for Wake' list the resources a device depends on for
wake. Add a function to generate this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This device has a large set of ACPI tables. Bring these in from coreboot
so that full functionality is available (apart from SMI).
Signed-off-by: Simon Glass <sjg@chromium.org>
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX2x4MgAKCRDKSWXLKUoM
IZQtAJ9HpNwG5q3nHt9WedzLCTkr3YoLAACeJJ0Wlpp5p5xPzuPmnoo/Vi4MtNQ=
=yxRo
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.01
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
The MII management register block offset is different between
gianfar and etsec2 compatible devices, this patch is to fix
this issue by adding driver data for different compatible
string.
Fixes: 2932c5a802 ("net: tsec: fsl_mdio: add DM MDIO support")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
PXE and DHCP shouldn't be listed when commands are not enabled that's why
handle it in the same way as is done for Zynq and ZynqMP.
Fixes: ec48b6c991 ("arm64: versal: Add support for new Xilinx Versal ACAPs")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch does sed 's/SPL_FPGA_SUPPORT/SPL_FPGA/g' but also fixing Makefile
and zynqmp.c to simplify if/endif logic in zynqmp.c.
This change is mostly done to be able to use CONFIG_IS_ENABLED macro and
obj-$(CONFIG_$(SPL_)FPGA) in Makefile. For them symbols need to be in sync.
And removing one line from Topic Miami boards which is not needed because
symbol is not enabled via Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add MSCC header with delay definitions for VSC8531 and associated
family devices.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In the live tree API ofnode_parse_phandle_with_args, the cell_count
argument must be used when cells_name is NULL.
But this argument is not provided to the live DT function
of_parse_phandle_with_args even it is provided to
fdtdec_parse_phandle_with_args.
This patch adds support of the cells_count parameter in dev_ and
of_node API to allow migration and support of live DT:
- of_parse_phandle_with_args
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add boolean input argument @no_map to helper function
fdtdec_add_reserved_memory() to add or not "no-map" property
for an added reserved memory node.
Property no-map is used by the Linux kernel to not not map memory
in its static memory mapping. It is needed for example for the|
consistency of system non-cached memory and to prevent speculative
accesses to some firewalled memory.
No functional change. A later change will update to OPTEE library to
add no-map property to OP-TEE reserved memory nodes.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently of_match_ptr is used to avoid referencing compatible strings
when OF_CONTROL is not enabled. This behaviour could be improved by
taking into account also OF_PLATDATA, as when this configuration is
enabled the compatible strings are not used at all.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch moves the the config SYS_MALLOC_LEN to Kconfig
as it is already done for zynq arch in commit 01aa5b8f05
("Kconfig: Move config SYS_MALLOC_LEN to Kconfig for zynq").
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
On Qualcomm IPQ40xx SoC series, GCC clock IP also handles the resets.
So since this will be needed by further drivers, lets add a driver for the reset controller.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Provide fdtfile value in default env instead of setting
it dynamically in runtime.
Fixes: 85cb2bc686("apalis/colibri imx6: provide proper fdtfile value")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
