In arch/arm/cpu/arm1136/cpu.c we have:
#ifndef CONFIG_SYS_CACHELINE_SIZE
#define CONFIG_SYS_CACHELINE_SIZE 32
#endif
,so there is no need to define 'CONFIG_SYS_CACHELINE_SIZE' with the default
size in the board config file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The wandboard solo version should boot the 'imx6dl-wandboard.dtb' file, since
dual-lite and solo variants are the same SoC with only the number of cores being
different.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Add a driver for the TPS65910 PMIC that is found in the AM335x GP EVM,
AM335x EVM SK and others.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
[trini: Split and rework Avinash's changes into new drivers/power
framework]
Signed-off-by: Tom Rini <trini@ti.com>
Add a driver for the TPS65217 PMIC that is found in the Beaglebone
family of boards.
Signed-off-by: Greg Guyotte <gguyotte@ti.com>
[trini: Split and rework Greg's changes into new drivers/power
framework]
Signed-off-by: Tom Rini <trini@ti.com>
The SPDX License List version 1.19 now contains an official entry for
the IBM-pibs license. However, instead of our suggestion "ibm-pibs",
the SPDX License List uses "IBM-pibs", with the following rationale:
"The reason being that all other SPDX License List short identifiers
tend towards using capital letters unless spelling a word. I'd prefer
to be consistent to this end".
Change the license IDs to use the official name.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix various misspellings of things like "environment", "kernel",
"default" and "volatile", and throw in a couple grammar fixes.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Since UBIFS is enabled for cpux9k2, more malloc space is needed.
For the current uboot 2013.10-rcX the size is to small, this will fix the
startup problems by increasing the malloc space to 4MiB.
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
When CONFIG_MMC_SPI is not enabled, the MMC_MODE_SPI capability can
never be set. However there is code in mmc.c which uses the
mmc_host_is_spi macro to check that capability & act accordingly. If we
expand that macro to 0 when CONFIG_MMC_SPI is not set (since it will
always be 0 at runtime anyway) then the compiler can optimize away the
SPI-specific code paths in mmc.c.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Samsung SoC is supported the WIDE8, even if Controller version is v2.0.
So add the SDHCI_QUIRK_USE_WIDE8 for Samsung-SoC.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Nicolas Colombain <nicolas.colombain@armadeus.com>
Without this patch, SPD access will fail which leads to DDR init fail.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Acked-by: York Sun <yorksun@freescale.com>
Add STMP3780-based Sansa Fuze+ board. This board is a small PMP
device sporting a CPU which was later rebranded to i.MX233 .
Currently supported is USB gadget mode and MMC .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Add STMP3780-based XFi3 board. This board is a small PMP device
sporting a CPU which was later rebranded to i.MX233 . Currently
supported is USB gadget mode and both external SD and internal
Phison SD-NAND bridge .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
LCD4 needs a slightly different GPIO configuration than the
original LWMON5 variant. GPIO49 needs to be configured to a
default output value of 0 (permanent voltage supply).
Additionally lcd4 also needs to enable the LSB transmitter.
Signed-off-by: Stefan Roese <sr@denx.de>
For most boards which define CONFIG_SPL_PAD_TO,
it is defined in config header files.
Currently, there exists only one exception, cam_enc_4xx board.
This patch moves CONFIG_SPL_PAD_TO definition
from board/ait/cam_enc_4xx/config.mk
to include/configs/cam_enc_4xx.h.
With this modification, we can delete a glue code
in the top level config.mk:
ifneq ($(CONFIG_SPL_PAD_TO),)
CPPFLAGS += -DCONFIG_SPL_PAD_TO=$(CONFIG_SPL_PAD_TO)
endif
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Heiko Schocher <hs@denx.de>
libata already has similar functions as implemented in the ahci code.
Refactor the code to use the libata variants and remove the dependency on
ata.h. Convert some defines to use the version from libata.h. Also, remove
some unnecessary memset's of bss data.
This is a step toward hopefully merging ahci.c and dw_ahsata.c which are
essentially the same driver.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Tom Rini <trini@ti.com>
gcc allows extensions to be non compiler specific by defining
__* macros for the attributes supported by gcc. Having a
different definition causes many warnings during the build
(cdefs.h on FreeBSD uses __attribute((__pure__)) where u-boot
uses __attribute__((pure)) for example). Do not redefine
these macros to suppress these warnings.
This patch ignores the checkpatch warning:
WARNING: __packed is preferred over __attribute__((packed))
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Somewhere along the line of refactoring the am335x header files, the
kernel image load was lost, so put it back in.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Separating the configuration file for Virtual
Target and real hardware Cyclone V development kit
Signed-off-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
This adds the "test_compression" command when building the sandbox. This
tests the existing compression and decompression routines for simple
sanity and for buffer overflow conditions.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Add mkimage support for generating and verifying MXS bootstream.
The implementation here is mostly a glue code between MXSSB v0.4
and mkimage, but the long-term goal is to rectify this and merge
MXSSB with mkimage more tightly. Once this code is properly in
U-Boot, MXSSB shall be deprecated in favor of mkimage-mxsimage
support.
Note that the mxsimage generator needs libcrypto from OpenSSL, I
therefore enabled the libcrypto/libssl unconditionally.
MXSSB: http://git.denx.de/?p=mxssb.git;a=summary
The code is based on research presented at:
http://www.rockbox.org/wiki/SbFileFormat
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
This patch add new functions to pmic max77686 to set voltage and mode.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Arndale board is based on samsung's exynos5250 soc.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Re-group the general options to note things that can be removed safely
to reduce binary size when not required, and expand the comment about
what commands we do include to note it could be replaced with a specific
list of required one. While at it, move the CMD parts of various
blocks IP to the end of the list for consistency.
Signed-off-by: Tom Rini <trini@ti.com>
After examining both TRMs and doing some experimentation, we can rely on
using the start of the download area for CONFIG_SPL_TEXT_BASE and then
move SRAM_SCRATCH_SPACE_ADDR up, just like am335x. This is required for
peripheral boot modes such as UART.
Signed-off-by: Tom Rini <trini@ti.com>
We only need this library when we're doing "disk" access to MMC/SD.
Update comment around the rest of CONFIG_SPL_LIB* to note that the
others are always required.
Signed-off-by: Tom Rini <trini@ti.com>
We had been allowing the max size to be larger than actually allowed by
the ROM. Expand the commentary here to explain why we set these
locations.
Signed-off-by: Tom Rini <trini@ti.com>
Now that IGEP base boards default environment use
the bootz command to boot a zImage instead of a
uImage, it makes sense to add support to supply a
raw initrd image to the kernel if needed.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Use CONFIG_MACH_TYPE generic macro to set the machine type
number in the common arm code instead of setting it in the
board code.
Signed-off-by: Oleksandr Tyshchenko <oleksandr.tyshchenko@ti.com>
Since config.mk is deprecated, remove this file,
and move CONFIG_SYS_TEXT_BASE define to config file.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Since config.mk is deprecated, remove this file,
and move CONFIG_SYS_TEXT_BASE define to config file.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Wolfgang Denk <wd@denx.de>
With the new include structure for TI platforms, we need to not define
our own CONFIG_SYS_PROMPT and also need to include
<configs/omap5_common.h> much sooner, so do both of these. Also drop
the unused CONFIG_NET_MULTI
Signed-off-by: Tom Rini <trini@ti.com>
Update the Makefiles so that all boards can use the same spl generation tool
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
updating an ubi partition needs a completely erased mtd partition,
see:
http://lists.infradead.org/pipermail/linux-mtd/2011-May/035416.html
So, add partubi alt setting for the dfu_alt_info environment
variable to mark this partition as an ubi partition. In case we
update an ubi partition, we erase after flashing the image into the
partition, the remaining sektors.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Add the USB ehci support for the OMAP5 uEVM.
Configure the uEVM mux data
Add the flags to build the appropriate modules
Add the usb call backs to initialize the EHCI controller
Signed-off-by: Dan Murphy <dmurphy@ti.com>
remove the config.mk file
move text base define to board config file for following boards
- at91sam9m10g45ek
- at91sam9x5ek
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
fix typo error for CONFIG_ENV_IS_NOWHERE from CONIG_ENV_IS_NOWHERE
Signed-off-by: Bo Shen <voice.shen@gmail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The CONFIG_MAX_NAND_CHIPS never used, remove it
No where define LCD_TEST_PATTERN, so no need undefine
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Since kernel code current use many dev_xxx() instead of using printk. To
compatible, move those dev_xxx from usb driver to linux/compat.h. Then all
driver code can use dev_err, dev_info and dev_vdbg.
This patch also removed duplicated macro definitions in usb driver.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Define the galois index table offset in chip head file. So user do not need
to set by himself. Driver will set it correctly according to sector_size.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
[rebased on master]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
as the at91sam9n12 and at91sam9x5 soc support PMECC, when use u-boot
to flash the rootfs, in order to avoid flash one sector with all 0xff
into NAND, so use nand trimffs subcommand to avoid it
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
add gmac support for sama5d3xek board, the gmac embedded in:
- sama5d33, sama5d34, sama5d35
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The target uses AUART 3 instead of the DUART for console output.
Signed-off-by: Andreas Wass <andreas.wass@dalelven.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
85xx, 86xx PowerPC folders have code variables with CamelCase naming conventions.
because of this code checkpatch script generates "WARNING: Avoid CamelCase".
Convert variables name to normal naming convention and modify board, driver
files with updated the new structure.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
TPL is introduced in the patch "NAND: TPL : introduce the TPL
based on the SPL", here enable TPL for p1022ds nand boot.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
The code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.
The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that
ddr spd code can get the interleaving mode setting in env. It loads
final uboot image from offset 96KB.
* final uboot image, size is variable depends on the functions enabled.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
1. The symbol CONFIG_SPL_NAND_MINIMAL is unused, so deleted it.
2. Some functions were unused in the minimal SPL, but it is useful
in the common SPL. So, enabled some functionality for common SPL.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
New I2C framework, introduced after v2013.07 final release, imposed I2C
code adjustment for some Samsung boards - namely Trats, GONI and Universal_c210.
Those boards were using schematic based I2C enumeration (I2C_5, I2C_9).
However, new I2C framework imposes usage of logical I2C adapters numbering
(e.g. I2C_0, I2C_1, etc).
Additionally, I2C_GET_* macros were replaced with i2c_*_bus_num() functions.
Trats board gained definition of second soft I2C adapter.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
The I2C_MULTI_BUS needs to be defined for correct I2C operation with
many software emulated I2C controllers.
This fix restores correct value of the I2C_MULTI_BUS changed by following
commit:
SHA1: 385c9ef5a7
i2c: add i2c_core and prepare for new multibus support
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
This way, we don't have to run mkimage on them.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Disabling the data cache is no longer required to boot Dalmore, so
enable it. This results in notably better performance when loading
and booting the Linux kernel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Currently all Tegra SoCs are assumed to have 32 byte cache lines. This
isn't true for Tegra114, however, which uses 4 Cortex-A15 cores and
therefore uses a cache line size of 64 bytes. Move the cache line size
setting to the per-SoC common configuration file.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This commit adapts the files that were derived from PIBS (PowerPC
Initialization and Boot Software) codeto using SPDX License
Identifiers.
So far, SPDX has not assigned an official License ID for the PIBS
license yet, so this should be considered preliminary.
Note that the following files contained incorrect license information:
arch/powerpc/cpu/ppc4xx/4xx_uart.c
arch/powerpc/cpu/ppc4xx/start.S
arch/powerpc/include/asm/ppc440.h
These files included, in addition to the GPL-2.0 / ibm-pibs dual
license as inherited from PIBS, a GPL-2.0+ license header which was
obviously incorrect. This has been removed.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Conflicts:
Licenses/README
Acked-by: Stefan Roese <sr@denx.de>
The __* keywords are reserved. On FreeBSD __unused evaluates
to the attribute unused, causing a compilation failure.
Just use unused instead.
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
cc: joe.hershberger@gmail.com
Fixup an easy conflict over adding the clk_get prototype and USB_OTG
defines for am33xx having moved.
Conflicts:
arch/arm/include/asm/arch-am33xx/hardware.h
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Change to SPDX, fix a few compiler warnings, adapt to
CONFIG_OMAP_COMMON]
Signed-off-by: Tom Rini <trini@ti.com>
In case CONFIG_BOOTSTAGE is not defined, call from bootstage_mark_name()
show_boot_progress(), so get more BOOTSTAGE_ID* ids in show_boot_progress()
if CONFIG_BOOTSTAGE is not defined.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Simon Glass <sjg@chromium.org>
Update omap5_common.h to use ti_armv7_common.h, and in turn update
dra7xx_evm.h and omap5_uevm.h slightly. The biggest changes here are
that IP blocks which exist on the platform, and had clocks enabled,
now have the drivers being built as well.
Signed-off-by: Tom Rini <trini@ti.com>
We create two new files, include/configs/ti_armv7_common.h for all of
the common IP blocks and related features / commands we share in
virtually all of our platforms. We then create
include/configs/ti_am335x_common.h for everything common to the am335x
SoC leaving just the board specific parts to
include/configs/ti_am335x_common.h.
Signed-off-by: Tom Rini <trini@ti.com>
We defined PHYS_DRAM_1 to 0x80000000 (start of DRAM) and then used this
for CONFIG_SYS_SDRAM_BASE. But then we kept on referencing PHYS_DRAM_1
in other places. Change to directly setting CONFIG_SYS_DRAM_BASE and
then using that name in code.
Signed-off-by: Tom Rini <trini@ti.com>
IGEP boards now have Device Tree support in the mainline
kernel. To boot an IGEP board using a DT, a uEnv.txt plain
text file could be used to define a custom uenvcmd that will
be run by the default boot command.
It is more convenient to change the default boot command to
allow loading a FDT if it is stored in the boot dir of the
rootfs uSD/MMC partition.
If no FDT is found then the defaul command tries to boot a
zImage without a DT using legacy boot.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Able to load the kernel from some form of ext[234] or FAT. Also, with v3.9 and
later of the Linux Kernel, uImage isn't builtable anymore by default, so we
should switch to use the bootz command.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
As config was originally based on am335x_evm.h we have also some
duplicate / unnused #defines.
Commit 15191c91 removed these #defines on various AM335x boards but not
for IGEP COM AQUILA. This patch simply removes them for this board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Add to the default environment the possibily to boot from NAND using
a ubi rootfs. Also the partition scheme is set as follows:
Start Size
SPL : 0x00000000 0x00080000 (512KiB)
U-Boot : 0x00080000 0x00100000 (1MiB)
U-Boot Env : 0x00180000 0x00020000 (128KiB)
File System : 0x001C0000 -
The ubiboot script gets the kernel and the dtb file from the boot directory
of the File System.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Now, the default kernel to boot the IGEP COM AQUILA is device tree based. As
old kernel is deprecated we should adapt the boot commands to use DTB files.
Also, with v3.9 and later of the Linux Kernel, uImage isn't builtable anymore
by default, so we should switch to use the bootz command.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
After commit:
79cd2f814b config_cmd_default.h: Remove CONFIG_CMD_MEMTEST
It's not necessary to undef the CONFIG_CMD_MEMTEST, so we can remove it from
configuration file.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Adding a new CONFIG_OMAP_COMMON which is included by all boards
that needs to build cpu/armv7/omap-common folder.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Replace license header with SPDX license identifier.
Replace GPL-2.0 with GPL-2.0+.
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
fsl_usb.h file created to share data bewteen usb platform code
and usb ip driver. Internal phy structure definitions moved to
this file
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Removed stdio structure ops support on arm_dcc
driver, and need to register with serial core
so-that it can access like remianing serial drivers.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Fix the license header introduced by the following patches
Add TWR-P10xx board support
Add T4240EMU target
IDT8T49N222A configuration code
Add C29x SoC support
Add support for C29XPCIE board
Signed-off-by: York Sun <yorksun@freescale.com>
Without this change EDID_DETAILED_TIMING_VSYNC_OFFSET
and EDID_DETAILED_TIMING_VSYNC_PULSE_WIDTH macros can
not be used (compile error).
The fix is quite trivial: rename struct member to the
expected name.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This font is based on Linux drivers/video/console/font_mini_4x6.c as of commit:
commit bcfbeecea11c15e243f076d37d637c2598aff4fe
Author: Bjarni Ingi Gislason <bjarniig@rhi.hi.is>
Date: Sun Aug 12 15:05:10 2012 +0000
drivers: console: font_: Change a glyph from "broken bar" to "vertical line"
I removed these lines as they are useless in U-Boot:
#include <linux/font.h>
#define FONTDATAMAX 1536
Whole "const struct font_desc font_mini_4x6" block
This patch also adds a new configuration option to select this smaller font,
CONFIG_VIDEO_FONT_4X6 , but this is disabled by default. The default setting
is the regular "large" font.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
This patch moves all the font configuration values into video_font_data.h
so they are all in the right place with the font. The video_font.h now only
includes video_font_data.h and will allow us to select and include different
font once more fonts are added.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
[agust: fixed build warning for mcc200]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch changes some features of the a3m071/a4m2k board support:
- Add bootcounter support
- Update MTD env default to correct values
- Add mtdparts to bootargs for mtd partitioning via kernel cmdline
- Added some default env variables for easy updating (kernel, dtb)
- Change README to the updated flash locations
Signed-off-by: Stefan Roese <sr@denx.de>
- Add support for zc7100 device.
- FPGA programming on few of the SOC(zc7100) takes more
than 1sec, hence increased the program time by 4sec to
sync' all soc's.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
C29XPCIE board is a series of Freescale PCIe add-in cards to perform
as public key crypto accelerator or secure key management module. It
includes C293PCIE board, C293PCIE board and C291PCIE board.
- 512KB platform SRAM in addition to 512K L2 Cache/SRAM
- 512MB soldered DDR3 32bit memory
- CPLD System Logic
- 64MB x16 NOR flash and 4GB x8 NAND flash
- 16MB SPI flash
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Singed-off-by: Po Liu <Po.Liu@freescale.com>
[yorksun: Fixup include/configs/C29XPCIE.h]
Signed-off-by: York Sun <yorksun@freescale.com>
T4240 PCIe IP is version 3.0 and has some update comparing previous
QorIQ products.
1. Move Freescale specific register define
to
arch/powerpc/include/asm/fsl_pci.h
and update the register offset define for T4240.
2. add the status/control register define
use status/control register to judge the link status
3. The original code uses 'Programming Interface' field to judge if PCIE is
EP or RC mode, however, T4240 does not support this functionality.
According to PCIE specification, 'Header Type' offset 0x0e is used to
indicate header type, so for PCIE controller, the patch changes code to
use 'Header Type' field to identify if the PCIE is RC or EP mode.
This patch fixes the PCIe card link up issue on T4240QDS.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
1. Add CONFIG_SYS_DPAA_RMAN macro to t4240 and b4860.
2. Decrease RMan liodn offset number.
SET_RMAN_LIODN() is used to set liodn offset of RMan blocks 0-3.
For t4240 and b4860, RMan liodn base is assigned to 922, the original
offset number is too large that the liodn (base+offset 922+678 = 1600)
is greater than 0x500 the maximum liodn number.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
1) Add support in B4860 board files for using IDT driver where
IDT8T49N222A is a low phase noise Frequency Translator / Synthesizer
that generate different refclks for SerDes modules, used this driver
for reconfiguring SerDes1 Refclks(based on SerDes1 protocols)
for CPRI to work. CPRI works on 122.88MHz and default refclks coming
on board are not suitable for it
2) Move SerDes1 refclk1 source selection from eth_b4860qds.c file
to b4860qds board file, as SerDes1 Refclk1 would come from
PHY MUX in case of certain protocols, that have been checked here.
This change would make on board SGMIIs to work
3) Add I2C addresses for IDT8T49N222A devices in board/include file
4) Add define for PCA-I2C bus multiplexer, on which IDT devices exist
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
BSC9132QDS is a Freescale Reference Design Board for BSC9132 SoC which is a
integrated device that contains two powerpc e500v2 cores and two DSP
starcores.
To support DSP starcore
-Creating LAW and TLB for DSP-CCSR space.
-Creating LAW for DSP-core subsystem M2 and M3 memory
-Creating LAW for 1GB DDR which is connected exclusively to DSP-cores
Signed-off-by: Manish Jaggi <manish.jaggi@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Add new board p1020RDB-PD. P1020RDB-PD board was update from P1020RDB.
DDR changed from DDR2 1G to DDR3 2G.
NAND: 128 MiB
Flash: 64 MiB
Also change P1020RDB to P1020RDB-PC to distinguish from P1020RDB board.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
JEDEC spec requires the clocks to be stable before deasserting reset
signal for RDIMMs. Clocks start when any chip select is enabled and
clock control register is set. This patch also adds the interface to
toggle memory reset signal if needed by the boards.
Signed-off-by: York Sun <yorksun@freescale.com>
Add emulator support for T4240. Emulator has limited peripherals and
interfaces. Difference between emulator and T4240QDS includes:
ECC for DDR is disabled due the procedure to load images
No board FPGA (QIXIS)
NOR flash has 32-bit port for higher loading speed
IFC and I2C timing don't really matter, so set them fast
No ethernet
Signed-off-by: York Sun <yorksun@freescale.com>
Move CONFIG_FSL_CORENET define to config_mpc85xx.h. It is not board
specific feature and belongs to SoC header.
Signed-off-by: York Sun <yorksun@freescale.com>
TWR-P1025 Specification:
-----------------------
Memory subsystem:
512MB DDR3 (on board DDR)
64Mbyte 16bit NOR flash
One microSD Card slot
Ethernet:
eTSEC1: Connected to Atheros AR8035 GETH PHY
eTSEC3: Connected to Atheros AR8035 GETH PHY
UART:
Two UARTs are routed to the FDTI dual USB to RS232 convertor
USB: Two USB2.0 Type A ports
I2C:
AT24C01B 1K Board EEPROM (8 bit address)
QUICC Engine:
Connected to DP83849i PHY supply two 10/100M ethernet ports
QE UART for RS485 or RS232
PCIE:
One mini-PCIE slot
Signed-off-by: Michael Johnston <michael.johnston@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
[yorksun: Fixup include/configs/p1_twr.h]
Signed-off-by: York Sun <yorksun@freescale.com>
In case only the CONFIG_SYS_I2C_SPEED is set in configuration file,
the CONFIG_SYS_I2C_SOFT_SPEED is defined as CONFIG_SYS_I2C_SPEED.
The CONFIG_SYS_I2C_SOFT_SPEED is then used throughout the driver.
Unfortunatelly, due to a typo in the driver, instead of defining
CONFIG_SYS_I2C_SOFT_SPEED, an CONFIG_SYS_SOFT_I2C_SPEED was defined
and therefore the driver failed to compile. The same applies for
CONFIG_SYS_I2C_SOFT_SLAVE , where the swap happens as well.
This patch fixes the issue.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Now that nothing uses CONFIG_ARCH_DEVICE_TREE, stop defining it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Aside from microblaze, all other SoCs/boards/vendors store their DT files
in board/$vendor/dts/$soc-$board.dts. Move microblaze-generic.dts to this
location for consistency.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Some boards, such as the BeagleBone Black, have an eMMC chip intstead
of NAND. We can use the eMMC boot partition to store the environment,
since it isn't used for anything else. This allows us to have a
configurable environment on those boards.
Signed-off-by: Justin Waters <justin.waters@timesys.com>
The BeagleBone Black can boot from either the MMC card
or eMMC chip on board. We should try both interfaces.
This modification also allows a graceful fallback if
a device exists but boot images are not present on it.
Changes for v2:
* Fix boot partition - it should always show up as mmcblk0p2
* Fix missing FDT load
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Many modern U-Boot ports enable command line editing and
a history buffer. The am335x_evm configuration is fairly
comprehensive as it is, so a few extra kb should not be
noticable, and it adds a very convenient feature.
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Give the user the ability to disable NAND support by defining
CONFIG_NO_NAND. This will allow custom hardware to easily support
this configuration.
Signed-off-by: Justin Waters <justin.waters@timesys.com>
[trini: Make apply on top of other series]
Signed-off-by: Tom Rini <trini@ti.com>
NOR requires that s_init be within the first 4KiB of the image so that
we can perform the rest of the required pinmuxing to talk with the rest
of NOR that we are found on. When NOR_BOOT is set we save our
environment in NOR at 512KiB and a redundant copy at 768KiB. We avoid
using SPL for this case and u-boot.bin is written directly to the start
of NOR.
We enclose the DMM-related parts of arch/arm/cpu/armv7/am33xx/emif4.c
with TI81xx checks as at this time U-Boot does not discard unused
sections in the main build and this code relies on functions specific to
(and only provided in) ti81xx-related code.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds support for the NOR module that attaches
to the memory cape for a Beaglebone board. This does not
add booting support; only support so that you can boot from
SD/MMC and see the NOR module so that it can be programmed.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
[trini: Clean up config changes slightly]
Signed-off-by: Tom Rini <trini@ti.com>
- Style cleanup (# define -> #define)
- Due to ROM issues, redudant loading isn't feasible, so drop.
- Given extra space, increase max size of U-Boot to 512KiB
- Correct env size to match usage (we had not re-defined ENV_SIZE).
- Given extra space, keep env size as 128KiB, add redundant environment.
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Tom Rini <trini@ti.com>
We always set a CONFIG_ENV_IS_...somewhere... so drop the initial define
of NOWHERE.
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Tom Rini <trini@ti.com>
This commit adds some prototypes into include/mtd/cfi_flash.h.
These functions are defined with a weak attribute in
drivers/mtd/cfi_flash.c.
This means they can be overrided by board-specific ones
if necessary.
When defining such functions under board/ directory or
somewhere, cfi_flash.h should be included.
This makes sure that board-specfic cfi functions
are defined in a correct prototype.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch extends dfu code to support transmission with -R switch
specified at dfu-util.
When -R is specified, the extra USB_REQ_DFU_DETACH request is sent after
successful data transmission. Then dfu resources are released and reset
command is issued.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The requests sent to the controller are not properly cache aligned
most of the time, thus implement a simple bounce buffer to avoid
problem with cache.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Allocate the qTD items all at once instead of allocating them
separately. Moreover, make sure each qTD is properly aligned
to 32-bytes boundary and that cache can be safely flushed over
each qTD touple.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Both the endpoint queue head and the endpoint item list is a controller
specific thing. Move them both into controller private data.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The usb_lowlevel_init() call already fills and passes back struct
ehci_ctrl , which readily contains correctly determined address of
the port register block address computed from values from controller
configuration registers. Leverage this and make use of this value
as this makes the code mode universal, but also gets us rid of the
CONFIG_USB_REG_BASE configuration option.
Moreover, this patch cleans up the usb_gadget_register_driver() call
a little by correcting the error handling. Note the usb_lowlevel_init()
and mvudc_probe() are now called in reversed order, but this has no
impact on the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Move the constant values that are programmed into mv_ep.ep into
separate static const structure so they can be memcpy()'d when
the initialization happens.
Moveover, we only every init NUM_ENDPOINTS, not 2 * NUM_ENDPOINTS,
so fix this bug as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The endpoints are operated on a per-controller basis, move the
endpoint array into controller's private data. Also shuffle the
struct mv_ep structure definition just above the definition of
the struct mv_drv so they're well grouped together.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Do a coding-style cleanup of this file and throw away useless
defined values. These values were likely a result of a copy-paste
job.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Instead of duplicating HDMI setup code for every mx6 board, factor out the common code
Signed-off-by: Pardeep Kumar Singla <b45784@freescale.com>
Acked-By: Eric Nelson <eric.nelson@boundarydevices.com>
If no other bootoption works, try loading up device tree and zImage.
This is selected as the last option to allow backward compatibility as
well as support the recent trend in moving kernel boot to using zImage
and device tree.
NOTE: if uImage is present in bootpart, it will try this first and
will assume this is to be booted with bootm (so may be concatenated
image or plain vanilla ATAG MACHINE_ID based image)
Signed-off-by: Nishanth Menon <nm@ti.com>
For folks not using concatenated device tree with uImage, having
an handy function to find and load device tree is very handy.
So introduce findfdt and loadfdt and run findfdt by default to make
it easier on user scripts.
Signed-off-by: Nishanth Menon <nm@ti.com>
CMD_FS_GENERIC allows us to simplify where we load up our image from
either from ext2/fat etc. So, lets use that instead of cumbersome
options we currently use. Sticking with existing conventions,
defaults will be:
ramdisk=ramdisk.gz
bootpart=0:2 (second partition)
bootdir=/boot (/boot in second partition)
This matches with the default behavior, these can be overriden by
env files as needed.
Signed-off-by: Nishanth Menon <nm@ti.com>
e682930867
(BeagleBoard: config: use uImage.beagle for tftp)
Introduced uImage.beagle which does not happen to be default output
file of Linux kernel build make uImage (output is uImage).
So, replace uImage.beagle with uImage
Signed-off-by: Nishanth Menon <nm@ti.com>
We do not use JFFS2 by default and it conflicts with
CONFIG_CMD_FS_GENERIC (ls command is the same). Since most of our
BOOTCMD can be simplified by using the FS_GENERIC, dropping JFFS2
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Joel Fernandes <joelf@ti.com>
BD ram address may vary in various SOC, so removing the hardcoding and
passing the same information through platform data
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
We use CONFIG_CMD_SPL_WRITE_SIZE when reading/writing the args portion
of falcon mode to NAND. Previously it was half the size of the
eraseblock which is too small, increase to eraseblock size.
Signed-off-by: Tom Rini <trini@ti.com>
The previous location used for the "args" portion of falcon mode was too
small to allow for a device tree to be saved there, so move the location
slightly and increase the size. In addition, our previous kernel
location was part of the area we set aside for U-Boot itself, so move it
up a bit higher.
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Now that we have falcon mode enabled, the partiton numbers for NAND have
changed, and we need to list entries for updating these parts of the
system. While adding falcon mode entires for eMMC (raw), we round up
the limit on U-Boot for ease of math later.
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
mx6qsabrelite and nitrogen6q boards are hardware compatible, so let's avoid the
code duplication and only use the nitrogen6x source code to make board code
maintainance easier.
Tested booting a mainline device tree kernel on a mx6qsabrelite board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
CONFIG_SYS_FLASH_PROTECTION was active on most gdsys boards by default,
while hardware flash protection was not implemented.
Hardware support was added recently and we get into trouble because backward
compatibility is broken (u-boot can't unprotect the protected flash after a
downgrade). So we decided to disable hardware flash protection for all our boards.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
A set of accessor functions was added to be able to access not only
memory mapped FPGA in a generic way.
Thanks to Wolfgang Denk for getting this sorted properly.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Conflict over SPDX changes means that one change was effectively dropped
as it was fixing typos in a removed hunk of text.
Conflicts:
arch/mips/cpu/mips64/start.S
Signed-off-by: Tom Rini <trini@ti.com>
Restrict autoboot interruption to "s" or "d" keys. This will prevent some
unwanted stopping and also allow disabling the reset on command timeout.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Accessing powered down peripherals will hang the bus, so check power
domain status before initializing SATA and fixup the FDT to disable
unused peripherals.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Various changes to highbank config:
Enable EFI partitions
Enable ext4 and FAT filesystems
Enable bootz command and raw initrd
Increase cmd and print buffer size to 1K
Change serial baudrate to 115200
Enable hush shell
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Qemu emulates a PCNET PCI card for the Malta CoreLV board.
Enable the pcnet driver and add board specific ethernet
initialization function to bring it up. Also enable the
CONFIG_CMD_NET and CONFIG_CMD_PING options.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Qemu emulates the Galileo GT64120 System Controller
which provides a CPU bus to PCI bus bridge.
The patch adds driver for this bridge and enables
PCI support for the emulated Malta board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Add minimal support for the MIPS Malta CoreLV board
emulated by Qemu. The only supported peripherial is
the UART.
This is enough to boot U-Boot to the command prompt
both in little and big endian mode.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
The Linux specific register access macros, the
extern function declarations and the UL suffixes
has been removed.
The header file will be used for the qemu-malta
board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.
Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h
Signed-off-by: Tom Rini <trini@ti.com>
Pull all the duplicate configuration options into configs/mxs.h
from the board configuration files. This reduces the files greatly
and makes them somewhat more readable. Besides, we do no longer
have such a horrible duplication of code.
Note that the mx23evk grew in size slightly. This is due to the
CONFIG_SYS_CBSIZE now being set to 1024 as it is on the rest of
MXS systems.
This patch also fixes the OCRAM size for i.MX23. The i.MX23 has
only 32kB of OCRAM, while i.MX28 has 128kB of OCRAM.
I verified the configuration didn't change for each of the boards,
but I didn't boot-test it on the boards I do not have. I configured
U-Boot for each board using the "make ... <board>_config" command
and then ran "cpp -I include -dM include/config.h" , which dumped
all the configuration options. I did this both before and after this
patch and finally compared the results for each MXS board. Actually,
the results do differ slightly, since the configs/mxs.h file now
properly includes the correct iomux-mx23.h or iomux-mx28.h , so
while comparing, I had to ignore these new defines. These have no
impact on U-Boot configuration though.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Add a header file, setup.h, which copy from Linux source code,
this file contain structures are used to pass initialisation parameters
to Linux. Enable this function on adp-ag101/adp-ag101p target
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
Cc: Macpaul Lin <macpaul@gmail.com>
The original adp-ag101/adp-ag101p initialize only one bank(64MB)
by default at boot time, but it is not enough for some application,
so increasing to two banks(128M).
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
Cc: Macpaul Lin <macpaul@gmail.com>
Even though the header files is used only by the
pci_ftpci100 driver, it contains declaration for
a function which is used by external code.
Move the header file to a common location which
lets external code use it.
Compile tested only.
Cc: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Add a const keyword to the sect_buf argument of
ide_write_data to fix the following warning:
cmd_ide.c: In function '__ide_output_data':
cmd_ide.c:548: warning: passing argument 2 of 'ide_write_data' discards qualifiers from pointer target type
/devel/u-boot.git/include/ide.h:76: note: expected 'ulong *' but argument is of type 'const ulong *'
Also modify the driver-model documentation to
match with the new prototype.
Compile tested only.
Cc: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Adds a new COMPAT string exynos5-hsi2c for high speed i2c controller
available on exynos5 SoCs from Samsung.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Due to the new I2C framework we need to adapt the u-boot update
function. Due to the new framework all i2c leafs behind a mux are
present in the system and not only those who are defined and used. So it
is bus number 5 after the rework.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This enables CONFIG_SYS_I2C on Tegra, updating existing boards and the Tegra
i2c driver to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heiko Schocher <hs@denx.de>
as the keymile boards use now the new i2c multibus/multiadapter
framework, remove the EEprom_ivm Environmentvar, as not longer
needed.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Holger Brunck <holger.brunck@keymile.com>
Tested-By: Holger Brunck <holger.brunck@keymile.com>
CONFIG_I2C_MUX is replaced through the new i2c multibus/multiadapter
framework, configured through CONFIG_SYS_I2C. As CONFIG_I2C_MUX
is only used on the keymile boards, and they are now completely
moved to the new framework, remove CONFIG_I2C_MUX.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Holger Brunck <holger.brunck@keymile.com>
Tested-By: Holger Brunck <holger.brunck@keymile.com>
- added to fsl_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
- added to soft_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
This Patch introduce the new i2c_core file, which holds
the I2C core functions, for the rework of the multibus/
multiadapter support.
Also adds changes in i2c.h for the new I2C multibus/multiadapter
support. This new support can be activated with the
CONFIG_SYS_I2C define.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Missing space for loaddtb command has been added. When missing, ext4load
fails with wrong number of passed parameters.
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
The gdsys ControlCenter Digital board is based on a Freescale P1022 QorIQ SOC.
It boots from SPI-Flash but can be configured to boot from SD-card for
factory programming and testing.
On board peripherals include:
- 2x GbE
- Lattice ECP3 FPGA connected via PCIe
- mSATA RAID1
- USB host
- DisplayPort video output
- Atmel TPM
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Extend the tpm library with support for single authorized (AUTH1) commands
as specified in the TCG Main Specification 1.2. (The internally used helper
functions are implemented in a way that they could also be used for double
authorized commands if someone needs it.)
Provide enums with the return codes from the TCG Main specification.
For now only a single OIAP session is supported.
OIAP authorized version of the commands TPM_LoadKey2 and TPM_GetPubKey are
provided. Both features are available using the 'tpm' command, too.
Authorized commands are enabled with CONFIG_TPM_AUTH_SESSIONS. (Note that
this also requires CONFIG_SHA1 to be enabled.)
Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc>
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Acked-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
With CONFIG_SYS_64BIT_LBA, lbaint_t gets defined as a 64-bit type,
which is required to represent block numbers for storage devices that
exceed 2TiB (the block size usually is 512B), e.g. recent hard drives
We now use lbaint_t for partition offset to reflect the lbaint_t change,
and access partitions beyond or crossing the 2.1TiB limit.
This required changes to signature of ext4fs_devread(), and type of all
variables relatives to block sector.
ext2/ext4 fs uses logical block represented by a 32 bit value. Logical
block is a multiple of device block sector. To avoid overflow problem
when calling ext4fs_devread(), we need to cast the sector parameter.
Signed-off-by: Frédéric Leroy <fredo@starox.org>
The files board/qi/qi_lb60/qi_lb60.c and include/configs/qi_lb60.h were
licensed under the GPL v3 or later, and not v2 or later. As this is
incompatible with the project, revert this board support until the
responsible parties are available to re-license (if so desired) under
GPL v2.
Signed-off-by: Tom Rini <trini@ti.com>
Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and
serial.
Conflicts:
arch/arm/dts/exynos5250.dtsi
Signed-off-by: Tom Rini <trini@ti.com>
If a specific configuraion is selected by the bootm command, e.g. with
'bootm 84000000#recoveryconf' we must honour this for not just the kernel,
but also the ramdisk and FDT.
In the conversion to using a common fit_image_load() function for loading
images from FITs (commits a51ec63 and 53f375f) this feature was lost.
Reinstate it by passing the selected configuration back from
fit_image_load() to boot_get_kernel(), then use this configuration
(which is stored in images->fit_uname_cfg) in both boot_get_ramdisk()
and boot_get_fdt().
Signed-off-by: Simon Glass <sjg@chromium.org>
OpenEmbedded has change partitioning layout of generated image so it
does not raise warnings during the boot regarding unkown partition
being used for U-Boot.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
OpenEmbedded has change partitioning layout of generated image so it
does not raise warnings during the boot regarding unkown partition
being used for U-Boot.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
OpenEmbedded has change partitioning layout of generated image so it
does not raise warnings during the boot regarding unkown partition
being used for U-Boot.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
OpenEmbedded has change partitioning layout of generated image so it
does not raise warnings during the boot regarding unkown partition
being used for U-Boot.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
OpenEmbedded has change partitioning layout of generated image so it
does not raise warnings during the boot regarding unkown partition
being used for U-Boot.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
OpenEmbedded has change partitioning layout of generated image so it
does not raise warnings during the boot regarding unkown partition
being used for U-Boot.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Jason Liu <r64343@freescale.com>
this is usefull when writing an UBI image which contains
and UBIFS volume (check README.nand and UBI FAQ for more
details)
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add USB EHCI, storage and network support.
Tested on Tegra30 Cardhu, and Tegra114 Dalmore
platforms. All works well.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra30 and Tegra114 are compatible except PLL parameters.
Tested on Tegra30 Cardhu, and Tegra114 Dalmore
platforms. All works well.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This function has no prototype in the headers and passes void * around, thus
requiring several casts. Tidy this up.
- Add new patch to clean up bootz_setup() function
Signed-off-by: Simon Glass <sjg@chromium.org>
Code for checking "splashpos" environment variable is
duplicated in drivers, move it to the common function.
Call this function also in the bmp display command to
consider "splashpos" settings.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Commit:
dfu: make data buffer size configurable
SHA1: 89a72b2e0e141042c9109185e02d39b2107ffc62
replaced statically allocated buffers with one allocated with memalign.
Malloc pool size of 1MiB was too small, since we needed bigger buffer to
transfer for example uImage.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch performs the following:
1) Convert the assembly code for memory and clock initialization to C code.
2) Move the memory and clock init codes from board/samsung to arch/arm
3) Creat a common lowlevel_init file across Exynos4 and Exynos5. Converted
the common lowlevel_init from assembly to C-code
4) Made spl_boot.c and tzpc_init.c common for both exynos4 and exynos5.
5) Enable CONFIG_SKIP_LOWLEVEL_INIT as stack pointer initialisation is already
done in _main.
6) exynos-uboot-spl.lds made common across SMDKV310, Origen and SMDK5250.
TEST: Tested SD-MMC boot on SMDK5250 and Origen.
Tested USB and SPI boot on SMDK5250
Compile tested for SMDKV310.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch configures the gpio values for UART
on Origen and SMDKV310 using pinmux
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
smdk5250-uboot-spl.lds is moved to common folder, so that it can be reused.
It is renamed to exynos-uboot-spl.lds
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Create splash.c/h to put the function and any future common splash
screen code in.
Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
When compressed image is loaded, it must be decompressed
to an aligned address + 2 to avoid unaligned access exception
on some ARM platforms.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Wolfgang Denk <wd@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
while playing with dfu, I tapped in an unaligned access
when doing on the host side a "lsusb -d [vendornr]: -v"
I get on the board:
GADGET DRIVER: usb_dnl_dfu
data abort
MAYBE you should read doc/README.arm-unaligned-accesses
pc : [<8ff71db8>] lr : [<8ff75aec>]
sp : 8ef40d18 ip : 00000005 fp : 00000000
r10: 00000000 r9 : 47401410 r8 : 8ef40f38
r7 : 8ef4aae8 r6 : 0000000a r5 : 8ef4ab28 r4 : 8ef4ab80
r3 : 0000000a r2 : 00000006 r1 : 00000006 r0 : 8ef4aae8
Flags: Nzcv IRQs off FIQs on Mode SVC_32
Resetting CPU ...
reason is that in the "struct usb_composite_dev" the
"struct usb_device_descriptor desc;" is on an odd address,
and this struct gets accessed in
drivers/usb/gadget/composite.c device_qual()
Fix it, by align this var "struct desc" fix to an aligned
address.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
add a weak dummy function g_dnl_fixup to add the possibility to update
the device_desc board specific. Used on the upcoming siemens board
support, where idVendor and idProduct is stored in an eeprom.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Dfu transfer uses a buffer before writing data to the
raw storage device. Make the size (in bytes) of this buffer
configurable through environment variable "dfu_bufsiz".
Defaut value is configurable through CONFIG_SYS_DFU_DATA_BUF_SIZE
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Tom Rini <trini@ti.com>
