The SYS_BOOT-based fallback shouldn't only check for one of the conditions of
use and then let the switch/case handle each boot device without enforcing the
conditions for each type of boot device again.
For instance, this behaviour would trigger the fallback for UART when
BOOT_DEVICE_UART is defined, CONFIG_SPL_YMODEM_SUPPORT is enabled (which should
be a show-stopper) and e.g. BOOT_DEVICE_USB is enabled and not
CONFIG_SPL_USB_SUPPORT.
Separating the logic for USB and UART solves this.
In addition, this adds support for more peripheral devices (USBETH and CPGMAC)
to the fallback mechanism. Note that the USBETH boot device should always be
different from the USB boot device (each should match a different bootrom
handoff case).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
DP83865 ethernet phy used on DRA74x-evm is quirky and the datasheet
provided IODELAY values for standard RGMII phys do not work.
Silicon Revision(SR) 2.0 provides an alternative bit configuration
that allows us to do a "gross adjustment" to launch the data off a
different internal clock edge. Manual IO Delay overrides are still
necessary to fine tune the clock-to-data delays. This is a necessary
workaround for the quirky ethernet Phy we have on the platform.
NOTE: SMA registers are spare "kitchen sink" registers that does
contain bits for other workaround as necessary as well. Hence the
control for the same is introduced in a generic SoC specific, board
generic location.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for detection of ES2.0 version of DRA7 family of
processors. ES2.0 is an incremental revision with various fixes
including the following:
- reset logic fixes
- few assymetric aging logic fixes
- MMC clock rate fixes
- Ethernet speed fixes
- edma fixes for mcasp
[ravibabu@ti.com: posted internal for an older bootloader]
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
As we discussed a couple of times, negative CONFIG options make our
life difficult; CONFIG_SYS_NO_FLASH, CONFIG_SYS_DCACHE_OFF, ...
and here is another one.
Now, there are three boards enabling OF_CONTROL on SPL:
- socfpga_arria5_defconfig
- socfpga_cyclone5_defconfig
- socfpga_socrates_defconfig
This commit adds CONFIG_SPL_OF_CONTROL for them and deletes
CONFIG_SPL_DISABLE_OF_CONTROL from the other boards to invert
the logic.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adds functions to enable and disable edma3 clocks which can be invoked
by drivers using edma3 to control the clocks.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Adds functions to enable and disable edma3 clocks which can be invoked
by drivers using edma3 to control the clocks.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add do_disable_clocks() to disable clock domains and module clocks.
These clocks are enabled using do_enable_clocks().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add do_disable_clocks() to disable clock domains and module clocks.
These clocks are enabled using do_enable_clocks().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Move arch/arm/cpu/armv7/exynos/* to arch/arm/mach-exynos/* to allow
reuse of existing code for ARMv8 based Exynos platforms.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add support for the mipi pll, this is necessary for getting higher dotclocks
with lcd panels.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We now have the CONFIG_SPL_DM for code within SPL to toggle caring about
DM or not. Without this change platforms that do enable CONFIG_DM but
not CONFIG_SPL_DM may be broken (such as OMAP5).
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
The "method" parameter was part of the original port of the driver from
the kernel. At some point this may have been added to allow for future
differentiation (as omap1 and omap2 have different GPIO IP blocks, so
this wasn't an unreasonable thing to do). At this point however it's
just extra overhead, so drop.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Re-sync DT files for am33xx with Linux Kernel v4.1
- Include DT file now for the "AM335x GP EVM" and build target for it,
via device tree and DM.
- We only need to provide platform data for UART when OF_CONTROL isn't
also enabled really. We can just push GPIO to coming from DT
Signed-off-by: Tom Rini <trini@konsulko.com>
Add spi clock to the list of am43xx basic clocks to make the SPI
subsystem available on am43xx systems.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Jagan Teki <jteki@openedev.com>
DRA72x processor variants are single core and it does not export ACP[1].
Hence, we have no source for generating an external snoop requests which
appear to be key to the deadlock in DRA72x design.
Since we build the same image for DRA74x and DRA72x platforms, lets
runtime detect and disable the workaround (in favor of performance) on
DRA72x platforms.
[1] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0438i/BABIAJAG.html
Suggested-by: Richard Woodruff <r-woodruff2@ti.com>
Suggested-by: Brad Griffis <bgriffis@ti.com>
Reviewed-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Add workaround for Cortex-A15 ARM erratum 801819 which says in summary
that "A livelock can occur in the L2 cache arbitration that might
prevent a snoop from completing. Under certain conditions this can
cause the system to deadlock. "
Recommended workaround is as follows:
Do both of the following:
1) Do not use the write-back no-allocate memory type.
2) Do not issue write-back cacheable stores at any time when the cache
is disabled (SCTLR.C=0) and the MMU is enabled (SCTLR.M=1). Because it
is implementation defined whether cacheable stores update the cache when
the cache is disabled it is not expected that any portable code will
execute cacheable stores when the cache is disabled.
For implementations of Cortex-A15 configured without the “L2 arbitration
register slice” option (typically one or two core systems), you must
also do the following:
3) Disable write-streaming in each CPU by setting ACTLR[28:25] = 0b1111
So, we provide an option to disable write streaming on OMAP5 and DRA7.
It is a rare condition to occur and may be enabled selectively based
on platform acceptance of risk.
Applies to: A15 revisions r2p0, r2p1, r2p2, r2p3 or r2p4 and REVIDR[3]
is set to 0.
Note: certain unicore SoCs *might* not have REVIDR[3] not set, but
might not meet the condition for the erratum to occur when they donot
have ACP (Accelerator Coherency Port) hooked to ACE (AXI Coherency
Extensions). Such SoCs will need the work around handled in the SoC
specific manner, since there is no ARM generic manner to detect such
configurations.
Based on ARM errata Document revision 18.0 (22 Nov 2013)
Suggested-by: Richard Woodruff <r-woodruff2@ti.com>
Suggested-by: Brad Griffis <bgriffis@ti.com>
Reviewed-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Current many cpu use the same flush_cache() function, which just call
the flush_dcache_range().
So implement a weak flush_cache() for all the cpus to use.
In original weak flush_cache() in arch/arm/lib/cache.c, there has some
code for ARM1136 & ARM926ejs. But in the arch/arm/cpu/arm1136/cpu.c and
arch/arm/cpu/arm926ejs/cache.c, there implements a real flush_cache()
function as well. That means the original code for ARM1136 & ARM926ejs
in weak flush_cache() of arch/arm/lib/cache.c is totally useless.
So in this patch remove such code in flush_cache() and only call
flush_dcache_range().
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Since some driver like ohci, lcd used dcache functions. But some ARM
cpu don't implement the invalidate_dcache_range()/flush_dcache_range()
functions.
To avoid compiling errors this patch adds an weak empty stub function
for all ARM cpu in arch/arm/lib/cache.c.
And ARM cpu still can implemnt its own cache functions on the cpu folder.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The LG Optimus Black (P970) codename sniper is a smartphone that was designed
and manufactured by LG Electronics (LGE) and released back in 2011.
It is using an OMAP3630 SoC GP version, which allows running U-Boot and the
U-Boot SPL from the ground up. This port is aimed at running an Android version
such as Replicant, the fully free Android distribution. However, support for
upstream Linux with device-tree and common GNU/Linux distros boot commands
could be added in the future.
For more information about the journey to freeing this device, please read the
series of blog posts at:
http://code.paulk.fr/article20/a-hacker-s-journey-freeing-a-phone-from-the-ground-up-first-part
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add CONFIG_OF_SUPPORT]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reboot mode is written in scratchpad memory before reboot in the form of a
single char, that is the first letter of the reboot mode string as passed to the
reboot function.
This mechanism is supported on OMAP3 both my the upstream kernel and by various
TI kernels.
It is up to each board to make use of this mechanism or not.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
USB devices are not really designed to get the power bounced off and on
at them. Esp. USB powered harddisks do not like this.
Currently we power off the USB ports both on a "usb reset" and when
booting the kernel, causing the usb-power to bounce off and then back
on again.
This patch removes the powering off calls, fixing the undesirable power
bouncing.
Note this requires some special handling for the OTG port:
1) We must skip the external vbus check if we've already enabled our own
vbus to avoid false positives
2) If on an usb reset we no longer detect that the id-pin is grounded, turn
off vbus as that means an external vbus may be present now
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Spring is the first ARM-based HP Chromebook 11. It is similar to snow
and it uses the same Samsung Exynos5250 chip. But has some unusual
features. Mainline support for it has lagged snow (both in kernel and
U-Boot). Now that the exynos5 code is common we can support spring just
by adding a device tree and a few lines of configuration.
Signed-off-by: Simon Glass <sjg@chromium.org>
Line up the display with the line below, e.g.:
CPU: Exynos5250 @ 1.7 GHz
Model: Google Spring
DRAM: 2 GiB
MMC: EXYNOS DWMMC: 0
Also show the speed as GHz where appropriate.
Signed-off-by: Simon Glass <sjg@chromium.org>
As a debugging aid, allow UART3 to be used as a debug UART in SPL. This
is a precursor to proper UART support, which requires a substantial
refactor.
Signed-off-by: Simon Glass <sjg@chromium.org>
USB-related options are usually prefixed with CONFIG_USB and platform-specific
adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so
this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Bootrom will put cpus into WFE state when boot cpu release cpus, so
target cpu cannot correctly go to spin state.
Add 'sev' to wakeup non-boot cpu that hold on bootrom space, let target
cpu can fall into u-boot spin table.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. Define two structures mx6ul_iomux_ddr_regs and mx6ul_iomux_grp_regs.
2. Add a new function mx6ul_dram_iocfg to configure dram io.
3. Refactor MMDC1 macro, discard "#ifdef CONFIG_MX6SX". Since
only mmdc0 channel exists on i.MX6SX/UL, redefine MMDC1 macro support
runtime check, but not hardcoding #ifdef macros.
4. Introduce mx6ul-ddr.h, which includes the register address for DRAM
IO configuration.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
1.Update WDOG settings.
2.No need to gate/ungate all PFDs for i.MX6UL.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
i.MX6UL features an Cortex-A7 core, it does not have PL310 as other i.MX6
chips. To Cortex-A7 core, If D-Cache is enabled, L2 Cache is enabled.
There is on specific switch for on/off L2 Cache, so default select
SYS_L2CACHE_OFF.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
1. Add enet, uart, i2c, ipg clock support for i.MX6UL.
2. Correct get_periph_clk, it should account for
MXC_CCM_CBCDR_PERIPH_CLK2_PODF_MASK.
3. Refactor get_mmdc_ch0_clk to make all i.MX6 share one function,
but not use 'ifdef'.
4. Use CONFIG_FSL_QSPI for enable_qspi_clk, but not #ifdef CONFIG_MX6SX.
5. Use CONFIG_PCIE_IMX for pcie clock settings, use CONFIG_CMD_SATA for
sata clock settings. In this way, we not need "#if defined(CONFIG_MX6Q)
|| defined....", only need one CONFIG_PCIE_IMX in header file.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
CPU_V7 is already selected by ARCH_MX6, so no point in selecting it again
by boards that depend on ARCH_MX6.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
cm-fx6 is an MX6 based board, and the menuconfig hierarchy should
reflect that. Make TARGET_CM_FX6 dependant on ARCH_MX6.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The i.MX6DQP has a PRG module, need to enable its clock for using IPU.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Brown Oliver <B37094@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Since the i.MX6QP has fixed the issue in boot ROM, so remove the workaround
for i.MX6QP.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Since i.MX6QP changes some CCM registers, so modify the clocks settings to
follow the hardware changes.
In c files, use runtime check and discard #ifdef.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add cpu type for i.MX6QP/DP.
This patch also fix is_mx6dqp(), since get_cpu_rev can return MXC_CPU_MX6QP
and MXC_CPU_MX6DP, we should use:
(is_cpu_type(MXC_CPU_MX6QP) || is_cpu_type(MXC_CPU_MX6DP)).
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Because the top-level Makefile forces all the source files
to include include/linux/kconfig.h (see the UBOOTINCLUDE define),
these includes are redundant.
By the way, there are exceptions for the statement above; host
programs. In fact, host tools in U-Boot depend on a particular
board configuration, although I think they should not. So, some
files still include <linux/config.h> to work around build errors
on host tools.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Simon Glass <sjg@chromium.org>
All am33xx device tree are using device-tree, so get_board_rev is never actually
called. Thus, we can get rid of it to make the code easier to maintain.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
Despite being defined with __weak, this declaration of get_board_rev will
conflict with the fallback one when ONFIG_REVISION_TAG is not defined.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces code to read the value of the SYS_BOOT pins on the OMAP5, as
well as the memory-preferred scheme for the interpretation of each value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This introduces code to read the value of the SYS_BOOT pins on the OMAP4, as
well as the memory-preferred scheme for the interpretation of each value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This introduces code to read the value of the SYS_BOOT pins on the OMAP3, as
well as the memory-preferred scheme for the interpretation of each value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
OMAP devices might boot from peripheral devices, such as UART or USB.
When that happens, the U-Boot SPL tries to boot the next stage (complete U-Boot)
from that peripheral device, but in most cases, this is not a valid boot device.
This introduces a fallback option that reads the SYS_BOOT pins, that are used by
the bootrom to determine which device to boot from. It is intended for the
SYS_BOOT value to be interpreted in the memory-preferred scheme, so that the
U-Boot SPL can load the next stage from a valid location.
Practically, this options allows loading the U-Boot SPL through USB and have it
load the next stage according to the memory device selected by SYS_BOOT instead
of stalling.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Now that SPL boot devices are clearly defined, we can use BOOT_DEVICE_QSPI_4
instead of a hardcoded value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This introduces OMAP3 support for the common omap boot code, as well as a
major cleanup of the common omap boot code.
First, the omap_boot_parameters structure becomes platform-specific, since its
definition differs a bit across omap platforms. The offsets are removed as well
since it is U-Boot's coding style to use structures for mapping such kind of
data (in the sense that it is similar to registers). It is correct to assume
that romcode structure encoding is the same as U-Boot, given the description
of these structures in the TRMs.
The original address provided by the bootrom is passed to the U-Boot binary
instead of a duplicate of the structure stored in global data. This allows to
have only the relevant (boot device and mode) information stored in global data.
It is also expected that the address where the bootrom stores that information
is not overridden by the U-Boot SPL or U-Boot.
The save_omap_boot_params is expected to handle all special cases where the data
provided by the bootrom cannot be used as-is, so that spl_boot_device and
spl_boot_mode only return the data from global data.
All of this is only relevant when the U-Boot SPL is used. In cases it is not,
save_boot_params should fallback to its weak (or board-specific) definition.
save_omap_boot_params should not be called in that context either.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
On some boards the otg is wired up in host-only mode in this case we
have no vbus-det gpio.
Stop logging an error from sunxi_usb_phy_vbus_detect() in this case, and
stop treating sunxi_usb_phy_vbus_detect() returning a negative errno, as
if a charger is plugged into the otg port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for reading the id pin value of the otg connector to the usb
phy code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Make possible using a single `u-boot-sunxi-with-spl.bin` binary for both NAND
memory and SD card. Detection where SPL was read from is implemented in
`spl_boot_device`.
Signed-off-by: Daniel Kochmański <dkochmanski@turtle-solutions.eu>
CC: Roy Spliet <r.spliet@ultimaker.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
[hdegoede@redhat.com: Some small coding style fixes]
Acked-by: Hans De Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
USB download gadget functions such as thor and dfu have a separate config option
for the USB gadget part of the code, independent from the command part.
This switches the fastboot USB gadget to the same scheme, for better
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
Base on PSCI services, implement CPU_ON/CPU_OFF for ls102xa platform.
Tested on LS1021AQDS, LS1021ATWR.
Test CPU hotplug times: 60K
Test kernel boot times: 1.2K
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
timer_wait is moved from sunxi/psci_sun7i.S, and it can be converted
completely into a reusable armv7 generic timer. LS1021A will use it
as well.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As the function 'sprintf' does not check buffer boundaries but outputs
to the buffer 'enet' of fixed size (16), this patch removes the function
'sprintf', and uses 'strcpy' instead. It will assign the character
arrays 'enet' and 'phy' the corresponding character strings.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
hab_status command returns a memory dump of the hab event log. But the
raw data is not human-readable. Parsing such data into readable event
will help to minimize debbuging time.
Signed-off-by: Ulises Cardenas <Ulises.Cardenas@freescale.com>
Add I2C4 clock support for i.MX6SX. Since we use runtime check,
but not macro, we need to remove `#ifdef ..` in crm_regs.h, or
gcc will fail to compile the code succesfully.
Making the macros only for i.MX6SX open to other i.MX6x maybe not
a good choice, but we have runtime check.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
enable_spi_clock does the same thing with enable_cspi_clock, so
remove enable_cspi_clock.
Remove enable_cspi_clock prototype in header file
convert cm_fx6/spl.c to use enable_spi_clk
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The A33 adds a pinmux function for UART0 in the PB pin group.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The original code was configuring the external pins after enabling
the R_PIO clock, which meant the configuration never made it to
the pin controller the first time in SPL.
Why this was working before is uncertain. Maybe the state was left
from a previous boot sequence, or RSB just happened to be the default
configuration. However with some A33 chips, SPL failed to configure
the PMIC. This was seen by me and Maxime on the Sinlinx SinA33 dev
board.
Reordering the calls fixed this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Commit 487b327 ("sunxi: GPIO pin mux hardware-feature-specific function
index defines") renamed all GPIO index defines, but missed the PORT F
UART0 setup functions.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
stv0991 has cadence qspi controller for flash interfacing, this
patch configures the device pads & clock for the controller.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
This reverts commit f76eba38b3.
This patch did not have a full and proper copyright/S-o-b chain.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Conflicts:
include/configs/sun6i.h
include/configs/sun8i.h
The DIGPROG register map:
23 ------- 16 | 15 ------ 8 | 7 --- 0 |
Major upper | Major Lower | Minor |
We also need to account for Major Lower.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
This is the first patch to remove the
CONFIG_SYS_EXTRA_OPTIONS.
This patch implements CPU type selection from Kconfig.
Further Kconfig stuff is added later.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.
Remove the configs that behave this way from the archs.
A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:
SPIFLASH
DISPLAY_BOARDINFO
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: Tom Rini <trini@konsulko.com>
DRA7/AM57xx devices can be operated in many different configurations.
When the SoC is supposed to support a configuration where low power mode
state may involve the SoC completely powered off and DDR is in self
refresh, SoC EMIF controller should not be the master of the reset
signal and an external entity might be in control of things.
The default configuration of Linux on TI evms involve not powering off
the voltage rails (due to various reasons including reliability concerns)
and must not allow DDR reset to be controlled by EMIF. On platforms
where external entity might control the reset signal, this configuration
will be a "dont care".
Fixes: 536d874708 ("ARM: DRA7: Update DDR IO registers")
Tested-by: Keerthy <j-keerthy@ti.com>
Acked-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently on sun6i after a "reset" the prompt returns and the user can
even type stuff until the watchdog triggers and does the actual reset.
This is somewhat unexpected behavior for the "reset" command, this
commit adds an endless loop to wait for the watchdog to trigger so that
we do not return to the prompt.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Unlike OMAP5, EMIF PHY used in DRA7 will be left in unknown state after
warm reset, emif needs to be configured to bring it back to a known
state. So configure EMIF during warm reset.
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The recent changes for hw leveling on am33xx were not intended for
DDR2 boards, only DDR3. Update emif_sdram_type to take a sdram_config
value to check against. This lets us pass in the value we would use to
configure, when we have not yet configured the board yet. In other cases
update the call to be as functional as before and check an already
programmed value in.
Tested-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
On AM57xx evm I2C5 is used to detect the LCD board by reading the
EEPROM present on the bus.
Enable i2c5 clocks to help that.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In addition to the regular mux configuration, certain pins of DRA7
require to have "manual mode" also programmed, when predefined
delay characteristics cannot be used for the interface.
struct iodelay_cfg_entry is introduced for populating
manual mode IO timings.
For configuring manual mode, along with the normal pad
configuration do the following steps:
- Select MODESELECT field of each assocaited PAD.
CTRL_CORE_PAD_XXX[8]:MODESELECT = 1(Enable MANUAL_MODE macro along with mux)
- Populate A_DELAY, G_DELAY values that are specified in DATA MANUAL.
And pass the offset of the CFG_XXX register in iodelay_cfg_entry.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
On DRA7, in addition to the regular muxing of pins, an additional
hardware module called IODelay which is also expected to be
configured. This "IODelay" module has it's own register space that is
independent of the control module.
It is advocated strongly in TI's official documentation considering
the existing design of the DRA7 family of processors during mux or
IODelay recalibration, there is a potential for a significant glitch
which may cause functional impairment to certain hardware. It is
hence recommended to do muxing as part of IOdelay recalibration.
IODELAY recalibration sequence:
- Complete AVS voltage change on VDD_CORE_L
- Unlock IODLAY config registers.
- Perform IO delay calibration with predefined values.
- Isolate all the IOs
- Update the delay mechanism for each IO with new calibrated values.
- Configure PAD configuration registers
- De-isolate all the IOs.
- Relock IODELAY config registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
do_set_mux32() is redefined in dra7xx and beagle_x15 boards.
IO delay recalibration sequence also needs this.
Making it generic to avoid duplication.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
When DLL_CALIB_INTERVAL is set, an extra delay is added
which is not required and it consumes EMIF bandwidth.
So making the DLL_CALIB_CTRL[8:0]DLL_CALIB_INTERVAL bits to 0.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
DDRIO_2 and LPDDR2CH1_1 registers are not present
for DRA7. So not configuring these registers for DRA7xx
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Updating EMIF registers to enable HW leveling
on DRA72-evm.
Also updating the timing registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
DRA7 EMIF supports Full leveling for DDR3.
Adding support for the Full leveling sequence.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
We plan to enable device tree in SPL by default. Before doing this,
explicitly disable it for all boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is used before jumping to U-Boot, but in that case we don't
always want to disable caches.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
This fixes ethernet no longer working on boards which use a gpio to enable
the phy.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Before this commit the code for determining the disconnect threshold was
checking for sun4i or sun6i assuming that those where the exception and
that newer SoCs use a disconnect threshold of 2 like sun7i does.
But it turns out that newer SoCs actually use a disconnect threshold of 3
and sun5i and sun7i are the exceptions, so check for those instead.
Here are the settings from the various Allwinner SDK sources:
sun4i-a10: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun5i-a13: USBC_Phy_Write(usbc_no, 0x2a, 2, 2);
sun6i-a31: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun7i-a20: USBC_Phy_Write(usbc_no, 0x2a, 2, 2);
sun8i-a23: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun8i-h3: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun9i-a80: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
Note this commit makes no functional changes for sun4i - sun7i, and
changes the disconnect threshold for sun8i to match what Allwinner uses.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
