DP-DDR is used for DPAA, separated from main memory pool for general
use. It has 32-bit bus width and use a standard DDR4 DIMM (64-bit).
Signed-off-by: York Sun <yorksun@freescale.com>
When CONFIG_SECURE_BOOT is enabled, the signed images
like kernel and dtb can be authenticated using iMX6 CAAM.
The added command hab_auth_img can be used for HAB
authentication of images. The command takes the image
DDR location, IVT (Image Vector Table) offset inside
image as parameters. Detailed info about signing images
can be found in Freescale AppNote AN4581.
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Using CPU_HAS_PCR micro to present the SoC has pcr
(peripheral control register).
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
When use pcr (peripheral control register), then we won't need
to care about the peripheral ID.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch implements a workaround to fix DDR3 memory issue.
The code for workaround detects PGSR0 errors and then preps for
and executes a software-controlled hard reset.In board_early_init,
where logic has been added to identify whether or not the previous
reset was a PORz. PLL initialization is skipped in the case of a
software-controlled hard reset.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Keegan Garcia <kgarcia@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch moves mx35 to the common timer functions added in commit
8dfafdd - Introduce common timer functions <Rob Herring>
The (removed) mx35 timer code (specifically __udelay()) could deadlock at
the 32-bit boundary of get_ticks(). get_ticks() returned a 32-bit value
cast up to a 64-bit value. If get_ticks() + tmo in __udelay() crossed
the 32-bit boundary, the while condition became unconditionally true and
locks the processor. Rather than patch the specific mx35 issues, simply
move everything over to the common code.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
This patch moves mx31 to the common timer functions added in commit
8dfafdd - Introduce common timer functions <Rob Herring>
The (removed) mx31 timer code (specifically __udelay()) could deadlock at
the 32-bit boundary of get_ticks(). get_ticks() returned a 32-bit value
cast up to a 64-bit value. If get_ticks() + tmo in __udelay() crossed
the 32-bit boundary, the while condition became unconditionally true and
locks the processor. Rather than patch the specific mx31 issues, simply
move everything over to the common code.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Helmut Raiger <helmut.raiger@hale.at>
This is an implementation of GPIOs for Tegra that uses driver model. It has
been tested on trimslice and also using the new iotrace feature.
The implementation uses a top-level GPIO device (which has no actual GPIOS).
Under this all the banks are created as separate GPIO devices.
The GPIOs are named as per the Tegra datasheet/header files: A0..A7, B0..B7,
..., Z0..Z7, AA0..AA7, etc.
Since driver model is not yet available before relocation, or in SPL, a
special function is provided for seaboard's SPL code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add macro which defines i2c_pads_info structs for multiple SoC types,
and a macro which selects the appropriate struct based on CPU type,
thus eliminating the need to manage multiple i2c pad configurations
manually when supporting multiple SoC types.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
"clang does not support global register variables; this is
unlikely to be implemented soon because it requires additional
LLVM backend support" [1]
Workaround it by obtaining the value of gd/r9 by an inline
asm routine. Note there is no set routine added for ARM at the
moment, since most if not all updates of gd from c are actually
not needed for ARM.
[1] http://clang.llvm.org/docs/UsersManual.html
cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
This patch is to add DCU driver support. DCU also named
2D-ACE(Two Dimensional Animation and Compositing Engine)
is a system master that fetches graphics stored in internal
or external memory and displays them on a TFT LCD panel.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
The QorIQ LS1 family is built on Layerscape architecture,
the industry's first software-aware, core-agnostic networking
architecture to offer unprecedented efficiency and scale.
Freescale LS102xA is a set of SoCs combines two ARM
Cortex-A7 cores that have been optimized for high
reliability and pack the highest level of integration
available for sub-3 W embedded communications processors
with Layerscape architecture and with a comprehensive
enablement model focused on ease of programmability.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Add get_lcd_clk and set_lcd_clk callbacks for Exynos5420 needed by
exynos video driver.
Also, configure ACLK_400_DISP1 as the parent for MUX_ACLK_400_DISP1_SUB_SEL.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Previously, we used to statically assign values for vl_col, vl_row and
vl_bpix using #defines like LCD_XRES, LCD_YRES and LCD_COLOR16.
Introducing the function exynos_lcd_early_init() would take care of this
assignment on the fly by parsing FIMD DT properties, thereby allowing us
to remove LCD_XRES and LCD_YRES from the main config file.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
There is no reason to redefine pure readl/writel functions.
So remove this redundancy.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Tegra board select menu to tegra/Kconfig.
Insert the Tegra SoC select menu between the arch select and the
board select.
Architecture select
|-- Tegra Platform (Tegra)
|- Tegra SoC select (Tegra20 / 30 / 114 / 124)
|- Board select
Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="tegra*") and always "select" CONFIG_SPL as follows:
config TEGRA
bool
select SPL
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
The bcm_ep board configuration is used by a number of boards
including Cygnus and NSP.
Add builds for the bcm958300k and the bcm958622hr boards.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
The iproc architecture code is present in several Broadcom
chip architectures, including Cygnus and NSP.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Add pin mux for NAND Flash Controller (NFC). NAND can be connected
using 8 or 16 data lines, this patch adds pin mux entries for all
16 data lines.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Enable Ethernet clock when Broadcom StarFighter2 Ethernet block
(CONFIG_BCM_SF2_ETH) is enabled.
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Enable initialization fo designware ethernet controller. With this
patch, ethernet works in my configuration, provided I set ethernet
address in the environment.
Signed-off-by: Pavel Machek <pavel@denx.de>
To fix the build error when build for Altera dev kit, not
virtual target. At same time, set the build for Altera dev
kit as default instead virtual target. With that, U-Boot
is booting well and SPL still lack of few drivers.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Structure defining clock manager hardware was wrong, leading to
wrong registers being accessed and hang in MMC init.
This fixes structure to match hardware.
Signed-off-by: Pavel Machek <pavel@denx.de>
When compiling u-boot with W=1 the extern inline void for
read* is likely causing the most noise. gcc / clang will
warn there is never a actual declaration for these functions.
Instead of declaring these extern make them static inline so
it is actually declared.
cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
This patch reads EFUSE_BOOTROM register to see the maximum supported
clock for CORE and TETRIS PLLs and configure them accordingly.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch adds support for parallel NOR device (S29GL512S10) present on J6-EVM.
The Flash device is connected to GPMC controller on chip-select[0] and accessed
as memory-mapped device. It has data-witdh=x16, capacity-64MBytes(512Mbits) and
is CFI compatible.
As multiple devices are share GPMC pins on this board, so following board
settings are required to detect NOR device:
SW5.1 (NAND_BOOTn) = OFF (logic-1)
SW5.2 (NOR_BOOTn) = ON (logic-0) /* Active-low */
SW5.3 (eMMC_BOOTn) = OFF (logic-1)
SW5.4 (QSPI_BOOTn) = OFF (logic-1)
And also set appropriate SYSBOOT configurations:
SW3.1 (SYSBOOT[ 8])= ON (logic-1) /* selects SYS_CLK1 speed */
SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */
SW3.3 (SYSBOOT[10])= ON (logic-1) /* wait-pin monitoring = enabled */
SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Non Muxed */
SW3.5 (SYSBOOT[12])= OFF (logic-0) /* device type: Non Muxed */
SW3.6 (SYSBOOT[13])= ON (logic-1) /* device bus-width: 1(x16) */
SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */
SW3.8 (SYSBOOT[15])= ON (logic-1) /* reserved */
Also, following changes are required to enable NOR Flash support in
dra7xx_evm board profile:
mx6sxsabresd board has 2 FEC ports, each one connected to a AR8031.
Add support for one FEC port initially.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This allows u-boot to load different OS or Bare Metal application on
different cores of the i.MX6 SoC.
For example: running Android on cpu0 and a RT OS like QNX/FreeRTOS on cpu1.
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Acked-by: Stefano Babic <sbabic@denx.de>
Do not specify own zynq specific SPL macros
because there is no need for that.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This adds board support for the Toradex Colibri T30 module.
Working functions:
- SD card boot
- eMMC environment and boot
- USB host/USB client (on the dual role port)
- Network (via ASIX USB)
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On Tegra114 and Tegra124 platforms, certain display-related registers cannot
be accessed unless the VPR registers are programmed. For bootloader, we
probably don't care about VPR, so we disable it (which counts as programming
it, and allows those display-related registers to be accessed).
This patch is based on the commit 5f499646c83ba08079f3fdff6591f638a0ce4c0c
in Chromium OS U-Boot project.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Jimmy Zhang <jimmzhang@nvidia.com>
Signed-off-by: Bryan Wu <pengw@nvidia.com>
[acourbot: ensure write went through, vpr.c style changes]
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <TWarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Terje Bergstrom <tbergstrom@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The hardware DQS gate training is a bit unreliable and does not
always find the best delay settings.
So we introduce a 32-bit 'dqs_gating_delay' variable, where each
byte encodes the DQS gating delay for each byte lane. The delay
granularity is 1/4 cycle.
Also we allow to enable the active DQS gating window mode, which
works better than the passive mode in practice. The DDR3 spec
says that there is a 0.9 cycles preamble and 0.3 cycle postamble.
The DQS window has to be opened during preamble and closed during
postamble. In the passive window mode, the gating window is opened
and closed by just using the gating delay settings. And because
of the 1/4 cycle delay granularity, accurately hitting the 0.3
cycle long postamble is a bit tough. In the active window mode,
the gating window is auto-closing with the help of monitoring
the DQS line, which relaxes the gating delay accuracy requirements.
But the hardware DQS gate training is still performed in the passive
window mode. It is a more strict test, which is reducing the results
variance compared to the training with active window mode.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
It is going to be useful in more than one place.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The stale error status should be cleared for all sun4i/sun5i/sun7i
hardware and not just for sun7i. Also there are two types of DQS
gate training errors ("found no result" and "found more than one
possible result"). Both are handled now.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The sun5i hardware (Allwinner A13) introduced configurable MBUS clock
speed. Allwinner A13 uses only 16-bit data bus width to connect the
external DRAM, which is halved compared to the 32-bit data bus of sun4i
(Allwinner A10), so it does not make much sense to clock a wider
internal bus at a very high speed. The Allwinner A13 manual specifies
300 MHz MBUS clock speed limit and 533 MHz DRAM clock speed limit. Newer
sun7i hardware (Allwinner A20) has a full width 32-bit external memory
interface again, but still keeps the MBUS clock speed configurable.
Clocking MBUS too low inhibits memory performance and one has to find
the optimal MBUS/DRAM clock speed ratio, which may depend on many
factors:
http://linux-sunxi.org/A10_DRAM_Controller_Performance
This patch introduces a new 'mbus_clock' parameter for the 'dram_para'
struct and uses it as a desired MBUS clock speed target. If 'mbus_clock'
is not set, 300 MHz is used by default to match the older hardcoded
settings.
PLL5P and PLL6 are both evaluated as possible clock sources. Preferring
the one, which can provide higher clock frequency that is lower or
equal to the 'mbus_clock' target. In the case of a tie, PLL5P has
higher priority.
Attempting to set the MBUS clock speed has no effect on sun4i, but does
no harm either.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The DRAM controller allows to configure impedance either by using the
calibration against an external high precision 240 ohm resistor, or
by skipping the calibration and loading pre-defined data. The DRAM
controller register guide is available here:
http://linux-sunxi.org/A10_DRAM_Controller_Register_Guide#SDR_ZQCR0
The new code supports both of the impedance configuration modes:
- If the higher bits of the 'zq' parameter in the 'dram_para' struct
are zero, then the lowest 8 bits are used as the ZPROG value, where
two divisors encoded in lower and higher 4 bits. One divisor is
used for calibrating the termination impedance, and another is used
for the output impedance.
- If bits 27:8 in the 'zq' parameters are non-zero, then they are
used as the pre-defined ZDATA value instead of performing the ZQ
calibration.
Two lowest bits in the 'odt_en' parameter enable ODT for the DQ and DQS
lines individually. Enabling ODT for both DQ and DQS means that the
'odt_en' parameter needs to be set to 3.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Remove the duplicated argument to | in two places. Reported
by Coccinelle (http://coccinelle.lip6.fr/).
Signed-off-by: Maxin B. John <maxin.john@enea.com>
According to the Reference Manual the 'mask_periph2_clk_sel_loaded' field of
register CCM_CIMR corresponds to bit 19 so fix its definition accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
According to the Reference Manual the 'wb_per_at_lpm' field of register
CCM_CLPCR corresponds to bit 16 so fix its definition accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
According to the Reference Manual the 'spdif0_clk_podf' field of register
CCM_CDCDR corresponds to bits 22, 23 and 24, so fix the mask and offset
definitions accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
'omux' field is not used anywhere and such layout is not valid for mx6solox.
Instead of adding more ifdef's into the structure, let's simply remove this
unused 'omux' field.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
At present arm defines CONFIG_SYS_GENERIC_GLOBAL_DATA, meaning that
the global_data pointer is set up in board_init_f(). However it is
actually set up before this, it just isn't zeroed.
If we zero the global data before calling board_init_f() then we
don't need to define CONFIG_SYS_GENERIC_GLOBAL_DATA.
Make this change (on arm32 only) to simplify the init process. I
don't have the ability to test aarch64 yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Tom Rini <trini@ti.com>
Implement SD driver for the S3C24xx family. This implementation
is currently only capable of using the PIO transfers, DMA is not
supported.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Unify the register structure so they can be easily used across all
of S3C24xx lineup.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
This patch add Marvell kirkwood MVSDIO/MMC driver
and enable it for Sheevaplugs and OpenRD boards.
Signed-off-by: Gerald Kerma <drEagle@doukki.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The commit adds three defines which will be used in
the EHCI driver to enable USB clock and assert
reset controllers of the corresponding PHYs.
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This enables the necessary clocks, in AHB0 and in PLL6_CFG. This is done
for sun7i only since I don't have access to any other sunxi platforms
with sata included.
The PHY setup is derived from the Alwinner releases and Linux, but is mostly
undocumented.
The Allwinner AHCI controller also requires some magic (and, again,
undocumented) DMA initialisation when starting a port. This is added under a
suitable ifdef.
This option is enabled for Cubieboard, Cubieboard2 and Cubietruck based on
contents of Linux DTS files, including SATA power pin config taken from the
DTS. All build tested, but runtime tested on Cubieboard2 and Cubietruck only.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Generate the PSCI node in the device tree.
Also add a reserve section for the "secure" code that lives in
in normal RAM, so that the kernel knows it'd better not trip on
it.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Implement core support for PSCI. As this is generic code, it doesn't
implement anything really useful (all the functions are returning
Not Implemented).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The current non-sec switching code suffers from one major issue:
it cannot run in secure RAM, as a large part of u-boot still needs
to be run while we're switched to non-secure.
This patch reworks the whole HYP/non-secure strategy by:
- making sure the secure code is the *last* thing u-boot executes
before entering the payload
- performing an exception return from secure mode directly into
the payload
- allowing the code to be dynamically relocated to secure RAM
before switching to non-secure.
This involves quite a bit of horrible code, specially as u-boot
relocation is quite primitive.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
In order to be able to use the various mode constants (far more
readable than random hex values), add the missing HYP and A
values.
Also update arm/lib/interrupts.c to display HYP instead of an
unknown value.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The errata is applicable on all OMAP4 (4430 and 4460/4470) and OMAP5
ES 1.0 devices. The current revision check erroneously implements this
on all DRA7 varients and with DRA722 device (which has only 1 EMIF instance)
infact causes an asynchronous abort and ends up masking it in CPSR,
only to be uncovered once the kernel switches to userspace.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This patch adds Keystone2 K2E SOC specific code to support
MSMC cache coherency. Also create header file for msmc to hold
its API.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch adds clock definitions and commands to support Keystone2
K2E SOC.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch adds hardware definitions specific to Keystone II
K2E device. It has a lot common definitions with k2hk SoC, so
move them to common hardware.h. This is preparation patch for
adding K2E SoC support.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch in general spit SoC type clock dependent code and general
clock code. Before adding keystone II Edison k2e SoC which has
slightly different dpll set, move k2hk dependent clock code to
separate clock-k2hk.c file.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Use KS2_ prefix in all definitions, for that replace K2HK_ prefix and
add KS2_ prefix where it's needed. It requires to change names also
in places where they're used. Align lines and remove redundant
definitions in kardware-k2hk.h at the same time.
Using common KS2_ prefix helps resolve redundant redefinitions and
adds opportunity to use KS2_ definition across a project not thinking about
what SoC should be used. It's more convenient and we don't need to worry
about the SoC type in common files, hardware.h will think about that.
The hardware.h decides definitions of what SoC to use.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
By default all DSPs are turned off, for another case option
to turn off them is added in this commit.
Also add command to turn off itself.
Acked-by: Murali Karicheri <m-maricheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
It's convinient to hold ddr3 function definitions in separate file
such as ddr3.h. So move this from hardware.h to ddr3.h.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Use common keystone2 Power Sleep controller base address instead of
directly deciding which keystone2 SoC is used in psc module.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
As noted by clang, we have been shifting certain values out of 32bit
range when setting some DDR registers. Upon further inspection these
had been touching reserved fields (and having no impact). These came in
from historical bring-up code and can be discarded. Similarly, we had
been declaring some fields as 0 when they will be initialized that way.
Tested on Beaglebone White.
Reported-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Cc: Ash Charles <ash@gumstix.com>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-By: Ash Charles <ashcharles@gmail.com>
Renesas R8A7794 is CPU with Cortex-A15. This supports the basic register
definition and GPIO and framework of PFC.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
On mx6solox there is an additional 0x4000 offset for the GPR registers.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
There is no need to keep iomuxc_base_regs structure as it serves the exact same
purpose of the iomuxc structure, which is to provide access to the GPR
registers.
The additional fields of iomuxc_base_regs are not used. Other advantage of
'iomuxc' is that it has a shorter name and the variable declarations can fit
into a single line.
So remove iomuxc_base_regs structure and use iomuxc instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Previously the driver was only tested on Power SoCs. Different barrier
instructions are needed for ARM SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
This patch enables CONFIG_CMD_GPIO for the Allwinner (sunxi) platform as well
as providing the common gpio API (gpio_request/free, direction in/out, get/set
etc).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Henrik Nordström <henrik@henriknordstrom.net>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Add support for the i2c controller found on all Allwinner sunxi SoCs,
this is the same controller as found on the Marvell orion5x and kirkwood
SoC families, with a slightly different register layout, so this patch uses
the existing mvtwsi code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Heiko Schocher <hs@denx.de>
[ ijc -- updated u-boot-spl-fel.lds ]
Note this has only been tested on Allwinner sunxi devices (support for which
gets introduced by a later patch).
The kirkwood changes have been compile tested using the wireless_space board
config, the orion5x changes have been compile tested using the edminiv2 board
config.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heiko Schocher <hs@denx.de>
mx6solox is the newest member of the mx6 family.
Some of the new features on this variants are:
- Cortex M4 microcontroller (besides the CortexA9)
- Dual Gigabit Ethernet
Add the initial support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The pad settings for DISP0_DATA02 and DISP0_DAT10 were not
set in the same way as DISP0_DAT00-23, causing much flicker
in parallel RGB displays on Dual-Lite and Solo processors.
These settings now match the i.MX6 Dual and Quad core versions.
Note that this fixes a regression in commit b47abc3 and that
this is the second time we've had a regression on these two
pads (See commit e654ddf).
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Newer AM437x silicon requires us to explicitly power up
the USB2 PHY. By implementing usb_phy_power() we can
achieve that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
* Boot failures have been discovered due to a combination of routing issues and
non optimal ddr3 timings in the EMIF
* Since ddr3 timings are different after significant board layout changes
different timings are required for alpha, beta and production boards.
Signed-off-by: Franklin S. Cooper Jr <fcooper@ti.com>
There is no way to reset the cpu, so use the watchdog for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Fix following compilation error when CONFIG_ARM64 is defined
Error: unknown or missing system register name at operand 2
-- `mrs x0,daifmsr daifset,#3'
Signed-off-by: Shaibal.Dutta <shaibal.dutta@broadcom.com>
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Darwin Rambo <drambo@broadcom.com>
Scan Manager driver will be called to configure the IOCSR
scan chain. This configuration will setup the IO buffer settings
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
To enable the DesignWare watchdog support at SOCFPGA
Cyclone V dev kit.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
This patch returns back support for old ep93xx processors family
Signed-off-by: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Cc: albert.u.boot@aribaud.net
This is not only more readable but also prevents a warning
about a missing prototype. The prototypes which are actually
missing are added.
cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@ti.com>
LS2085A is an ARMv8 implementation. This adds board support for emulator
and simulator:
Two DDR controllers
UART2 is used as the console
IFC timing is tightened for speedy booting
Support DDR3 and DDR4 as separated targets
Management Complex (MC) is enabled
Support for GIC 500 (based on GICv3 arch)
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Freescale LayerScape with Chassis Generation 3 is a set of SoCs with
ARMv8 cores and 3rd generation of Chassis. We use different MMU setup
to support memory map and cache attribute for these SoCs. MMU and cache
are enabled very early to bootst performance, especially for early
development on emulators. After u-boot relocates to DDR, a new MMU
table with QBMan cache access is created in DDR. SMMU pagesize is set
in SMMU_sACR register. Both DDR3 and DDR4 are supported.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
Make MMU function reusable. Platform code can setup its own MMU tables.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: David Feng <fenghua@phytium.com.cn>
This is needed for accessing peripherals with 64-bit MMIO registers,
from ARMv8 processors.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
The armv8 ARM Trusted Firmware (ATF) can be used to load various ATF
images and u-boot, and does this for virtual platforms by using
semihosting. This commit extends this idea by allowing u-boot to also
use semihosting to load the kernel/ramdisk/dtb. This eliminates the need
for a bootwrapper and produces a more realistic boot sequence with
virtual models.
Though the semihosting code is quite generic, support for armv7 in
fastmodel is less useful due to the wide range of available silicon
and the lack of a free armv7 fastmodel, so this change contains an
untested armv7 placeholder for the service trap opcode.
Please refer to doc/README.semihosting for a more detailed description
of semihosting and how it is used with the armv8 virtual platforms.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Cc: trini@ti.com
Cc: fenghua@phytium.com.cn
Cc: bhupesh.sharma@freescale.com
I2C read transactions are typically implemented as follows:
START(write) address REPEATED_START(read) data... STOP
However, Tegra's I2C driver currently implements reads as follows:
START(write) address STOP START(read) data... STOP
This sequence confuses at least the AS3722 PMIC on the Jetson TK1 board,
leading to corrupted read data in some cases. Fix the driver to chain
the transactions together using repeated starts to solve this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Yen Lin <yelin@nvidia.com>
Move AEMIF driver to drivers/memory/ti-aemif.c along with AEMIF
definitions collected in arch/arm/include/asm/ti-common/ti-aemif.h
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The definitions inside emif_defs.h concern davinci nand driver and
should be in it's header. So create header file for davinci nand
driver and move definitions from emif_defs.h and nand_defs.h to it.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
[trini: Fixup more davinci breakage]
Signed-off-by: Tom Rini <trini@ti.com>
According to:
http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/log/?h=imx_v2009.08_3.0.35_4.1.0
ENGR00287268 mx6: fix the secure boot issue on the new tapout chip
commit 424cb1a79e9f5ae4ede9350dfb5e10dc9680e90b
newer i.MX6 silicon revisions have an updated ROM and HAB API table.
Please see also:
i.MX Applications Processors Documentation
Engineering Bulletins
EB803, i.MX 6Dual/6Quad Applications Processor Silicon Revsion 1.2 to 1.3 Comparison
With this change the secure boot status is correctly displayed
Signed-off-by: Stefano Babic <sbabic@denx.de>
mx6 reference manual incorrectly states that the DEVICE_TYPE field of
IOMUXC_GPR12 register should be configured as '0010' for setting the PCI
controller in RC mode. The correct value should be '0100' instead.
This also aligns with the same value used in the mx6 pci kernel driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Sometimes Read DQ and DQS are not in phase. Since, this
phase shift differs from board to board, we need to
calibrate it at DRAM init phase, that's read DQ calibration.
This patch adds SW Read DQ calibration routine to compensate
this skew.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
mkconfig links ${objtree}/include/asm/proc/ to
${srctree}/arch/${arch}/include/asm/proc-armv/. This seems to be a
remnant from the past. Ever since its introduction in 2003 it is used
only in ARM build and always links to same place, so let's simplify
the code, remove it and reference directly where needed.
Successful MAKEALL for ARM and PowerPC verified on Linux.
Signed-off-by: Vasili Galka <vvv444@gmail.com>
Add QSPI support for VF610TWR, such as clock and iomux.
Signed-off-by: Alison Wang <Huan.Wang@freescale.com>
Signed-off-by: Chao Fu <b44548@freescale.com>
Similar to OMAP4/5 we need to scale the voltage up prior to changing the
clock frequencies up higher. Add a similar hook to start with.
Signed-off-by: Tom Rini <trini@ti.com>
For usage of timer6 within B&R we need this defines to enable clock
modules and clk-source.
Also the 'Timer register bits' are expanded.
By the way we add defines for all timers within AM335x SoC.
Cc: trini@ti.com
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Currently PWREMU_MGMT is not configured in the Linux generic UART
driver as this register seems to be specific TI UART IP. So this
needs to be enabled in u-boot to use UART1 from kernel space.
Acked-By: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
OMAP3 used GPMC_NAND_ECC_LP_x8_LAYOUT and GPMC_NAND_ECC_LP_x16_LAYOUT macros
to configure GPMC controller for x7 or x8 bit device connected to its interface.
Now this information is encoded in CONFIG_SYS_NAND_DEVICE_WIDTH macro, so above
macros can be completely removed.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Allow imx_iomux_v3_setup_multiple_pads to take a multi-cpu pad_list
and add macros for declaring the pad_list that take into account the
SoC types supported using CONFIG_MX6QDL (supports both the MX6Q and MX6DL
iomux).
Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
- add function for configuring iomux based on board-specific regs
- add function for configuring mmdc based on board-specific and
chip-specific data
Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add memory-mapped structures for MMDC iomux and configuration. Note that whi
the MMDC configuration registers are common between the IMX6DQ
(IMX6DUAL/IMX6QUAD) and IMX6SDL (IMX6SOLO/IMX6DUALLITE) types the iomux
registers differ. This requires two sets of structures.
Add structures to describe DDR3 device information, system information
(memory layout, etc), and MMDC calibration registers that can be used to
configure the MMDC dynamically.
We define these structures for SPL builds instead of including mx6q-ddr.h an
mx6dl-ddr.h which use the same namespace and are only useful for imximage cf
files.
Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
arch/arm/include/asm/spl.h requires all SoCs to have
arch/arm/include/asm/arch-*/spl.h.
But many of them just define BOOT_DEVICE_* macros.
Those macros are used in the "switch (boot_device) { ... }"
statement in common/spl/spl.c.
So they should not be archtecture specific, but be described as
a simpile enumeration.
This commit merges most of arch/arm/include/asm/arch-*/spl.h
into arch/arm/include/asm/spl.h.
With a little more effort, arch-zynq/spl.h and arch-socfpga/spl.h
will be merged, while I am not sure about OMAP and Exynos.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Bo Shen <voice.shen@atmel.com> [on sama5d3xek board for at91 part]
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stefano Babic <sbabic@denx.de> [applying Tim's i.MX6 patches]
Acked-by: Tom Rini <trini@ti.com>
Setting ps_hold ought to be one of the first things we do when we
first boot up. If we wait until the main u-boot runs we won't set it
in time and the PMIC may power us back off.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
If without switch to main crystal oscillator, the sama5d3 SoC will
use internal on chip RC oscillator.
In order to get better accuracy, switch to main crystal oscillator.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
On Mon, 2014-05-05 at 14:18 +0200, Stefan Roese wrote:
> > + case 1:
> > +#if CONFIG_MMC1_PG
> Are you sure that this is correct and shouldn't be:
>
> +#ifdef CONFIG_MMC1_PG
>
> ?
It's "correct" in so far as it works (the boards.cfg config stuff
#defines things to 1), but I think you are right that it isn't the
preferred style. But...
> A quick scan through this patch series shows that this define
> is not set at all. Perhaps its outdated? Or is it used to support
> some other sunxi SoC? Not sure, perhaps it should be removed for
> now.
...I had thought that it was to support some other board which wasn't
being upstreamed right now, so eventually useful and harmless for now,
but I've just checked and it isn't actually used by any of the boards in
u-boot-sunxi.git. So rather than fix it to use #ifdef lets drop it.
Rather than resend the entire series, here is v5.1 of this patch.
> Other than this please add my:
>
> Reviewed-by: Stefan Roese <sr@denx.de>
Thanks!
8<---------------------------------
>From 20704e35a41664de5f516ed0e02981ac06085102 Mon Sep 17 00:00:00 2001
From: Ian Campbell <ijc@hellion.org.uk>
Date: Fri, 7 Mar 2014 04:29:39 +0000
Subject: [PATCH v5.1 7/8] sunxi: mmc support
This adds support for the MMC controller on the Allwinner A20 (sun7i)
processor.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Wills Wang <wills.wang.open@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Cc: Aaron Maoye <leafy.myeh@allwinnertech.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: Tom Rini <trini@ti.com>
This patch adds generic board, start of day and basic build system support for
the Allwinner A20 (sun7i) processor. This code will not been compiled until the
build is hooked up in a later patch. It has been split out to keep the patches
manageable.
Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Patrick Wood <patrickhwood@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wills Wang <wills.wang.open@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>
This patch adds DRAM initialisation support for the Allwinner A20 (sun7i)
processor. This code will not been compiled until the build is hooked up in a
later patch. It has been split out to keep the patches manageable.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>
This patch adds the basic pinmux and gpio support for the Allwinner A20 (sun7i)
processor. This code will not been compiled until the build is hooked up in a
later patch. It has been split out to keep the patches manageable.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Henrik Nordström <henrik@henriknordstrom.net>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>
This patch adds the basic clocks and timer support for the Allwinner A20
(sun7i) processor. This code will not been compiled until the build is hooked
up in a later patch. It has been split out to keep the patches manageable.
Some of the code here is common to multiple sunxi subarchtectures, hence files
are named sun4i which is the earliest similar variant.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>
Set DDR_SEL_PAD_CONTR register explicitly to DDR3 which solves RAM
issues with newer silicon (1.1). This register was added in revision
4 of the Vybrid Reference Manual.
Signed-off-by: Stefan Agner <stefan@agner.ch>
The omap_hw_init_context function (and assorted helpers) is the same for
all OMAP-derived parts as when CHSETTINGS are used, that's the same and
our DDR base is also always the same. In order to make this common we
simply need to update the names of the define for DDR address space
which is also common.
Cc: Sricharan R. <r.sricharan@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
GPMC controller on TI's OMAP SoC is general purpose controller to interface
with different types of external devices like;
- parallel NOR flash
- parallel NAND flash
- OneNand flash
- SDR RAM
- Ethernet Devices like LAN9220
Though GPMC configurations may be different for each platform depending on
clock-frequency and external device interfacing with controller. But
initialization sequence remains common across all platfoms.
Thus this patch merges gpmc_init() scattered in different arch-xx/mem.c
files into single omap-common/mem-common.c
However, actual platforms specific register config values are still sourced
from corresponding platform specific headers like;
AM33xx: arch/arm/include/asm/arch-am33xx/mem.h
OMAP3: arch/arm/include/asm/arch-omap3/mem.h
OMAP4: arch/arm/include/asm/arch-omap4/mem.h
OMAP4: arch/arm/include/asm/arch-omap5/mem.h
Also, CONFIG_xx passed by board-profile decide config for which set of macros
need to be used for initialization
CONFIG_NAND: initialize GPMC for NAND device
CONFIG_NOR: initialize GPMC for NOR device
CONFIG_ONENAND: initialize GPMC for ONENAND device
Signed-off-by: Pekon Gupta <pekon@ti.com>
[trini: define GPMC_SIZE_256M for omap3]
Signed-off-by: Tom Rini <trini@ti.com>
This patch moves platform specific information for GPMC and ELM controller
into separate header files, so that any derivative devices do not mess other
header files.
Platform specific information added into arch-xx/../hardware.h
- CPU related platform specific details like base-address of GPMC and ELM
Platform specific information added into arch-xx/../mem.h
- Generic configs for GPMC and ELM initialization.
- Hardware parameters or constrains specific to GPMC and ELM IP like;
number of max number of chip-selects available
Signed-off-by: Pekon Gupta <pekon@ti.com>
This patch moves platform specific information for GPMC and ELM controller
into separate header files, so that any derivative devices do not mess other
header files.
Platform specific information added into arch-xx/../hardware.h
- CPU related platform specific details like base-address of GPMC and ELM
Platform specific information added into arch-xx/../mem.h
- Generic configs for GPMC and ELM initialization.
- Hardware parameters or constrains specific to GPMC and ELM IP like;
number of max number of chip-selects available
Signed-off-by: Pekon Gupta <pekon@ti.com>
Conflicts:
boards.cfg
Conflicts were trivial once u-boot-arm/master boards.cfg was
reformatted (commit 6130c146) to match u-boot/master's own
reformatting (commit 1b37fa83).
Modified the mmc_set_clock for eynos4.
The goal of this patch is that fsys-div register should be reset.
And retore the div-value, not using the value of lowlevel_init.
(For using SDMMC4, this patch is needs)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
A few changes are made to the Tegra EHCI driver so that it can set
everything up for device-mode operation on the first USB controller.
This can be used in conjunction with ci_udc.c to operate as a USB
device.
Detailed changes are:
* Rename set_host_mode() to set_up_vbus() since that's really what it
does.
* Modify set_up_vbus() to know whether it's initializing in host or
device mode, and:
- Skip the external VBUS check in device mode, since external VBUS is
expected in this case.
- Disable VBUS output in device mode.
* Modify init_phy_mux() to know whether it's initializing in host or
device mode, and hence skip setting USBMODE_CM_HC (which enables host
mode) in device mode. See the comments in that function for why this
is safe w.r.t. the ordering requirements of PHY selection.
* Modify init_utmi_usb_controller() to force "b session valid" in device
mode, since the HW requires this. This is done in UTMI-specific code,
since we only support device mode on the first USB controller, and that
controller can only talk to a UTMI PHY.
* Enhance ehci_hcd_init() to error-check the requested host-/device-mode
vs. the dr_mode (dual-role mode) value present in device tree, and the
HW configurations which support device mode.
* Enhance ehci_hcd_init() not to skip HW initialization when switching
between host and device mode on a controller. This requires remembering
which mode the last initialization used.
Cc: Jim Lin <jilin@nvidia.com>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Bootmode mask was defined as 0x0F, but documentation mentions 0x07.
Experiments show that bit "3" is the JTAG chain configuration.
Change the mask to "7" to allow systems with a different chain
configuration to boot correctly.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Acked-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added efuse status register base address. This register
is used for determining whether efuse was blown or not.
Also, added the zynq_get_silicon_version() to get the
silicon version of the zynq board.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The HW-defined procedure for booting Tegra requires that
CLAMP_INPUTS_WHEN_TRISTATED be enabled before programming the pinmux.
Add a function to the pinmux driver to allow boards to do this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The HW-defined procedure for booting Tegra requires that some pins be
set up as GPIOs immediately at boot in order to avoid glitches on those
pins, when the pinmux is programmed. Add a feature to the GPIO driver
which executes a GPIO configuration table. Board files will use this to
implement the correct HW initialization procedure.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Define enum PMUX_FUNC_DEFAULT, which indicates that a table entry passed
to pinmux_config_pingrp()/pinmux_config_pingrp_table() shouldn't change
the mux option in HW.
For pins that will be used as GPIOs, the mux option is irrelevant, so we
simply don't want to define any mux option in the pinmux initialization
table.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
If CONFIG_API is ever to be enabled on Tegra, this define must be set,
since api/api_storage.c uses it.
A couple of annoyting things about CONFIG_SYS_MMC_MAX_DEVICE
1) It isn't documented in README. The same is true for a lot of similar
defines used by api_storage.c.
2) It doesn't represent MAX_DEVICE but rather NUM_DEVICES, since the
valid values are 0..n-1 not 0..n.
However, I this patch does not address those shortcomings.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch includes following changes :
* Adds gpio pin numbering support for EXYNOS SOCs.
To have consistent 0..n-1 GPIO numbering the banks are divided
into different parts where ever they have holes in them.
* Rename GPIO definitions from GPIO_... to S5P_GPIO_...
These changes were done to enable cmd_gpio for EXYNOS and
cmd_gpio has GPIO_INPUT same as s5p_gpio driver and hence
getting a error during compilation.
* Adds support for name to gpio conversion in s5p_gpio to enable
gpio command EXYNOS SoCs. Function has been added to asm/gpio.h
to decode the input gpio name to gpio number.
Example: SMDK5420 # gpio set gpa00
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Some platforms (tested on mpc85xx, mpc86xx) use global data before calling
function baord_inti_f(). The data should not be cleared later. Any arch
which uses global data in generic board board_init_f() should define
CONFIG_SYS_GENERIC_GLOBAL_DATA.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
CC: Simon Glass <sjg@chromium.org>
CC: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Simon Glass <sjg@chromium.org>
gd->bd->bi_baudrate is a copy of gd->baudrate.
Since baudrate is a common feature for all architectures,
keep gd->baudrate only.
It is true that bi_baudrate was passed to the kernel in that structure
but it was a long time ago.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu> (For microblaze)
On mx6sl there is a LVE (Low Voltage Enable) bit in the IOMUXC_SW_PAD_CTL
register that can enable or disable low voltage on the pad.
LVE is bit 22 of IOMUXC_SW_PAD_CTL register, but in order to make the
calculation easier we can define it as a flag in bit 1, since this bit is unused.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Otavio Salvador <otavio@ossystems.com.br>
