This allows us to use the same DRAM init function on all archs. Add a
dummy function for arc, which does not use DRAM init here.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Dummy function on nios2]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a specific serial driver for Intel MID platforms.
It has special fractional divider which can be programmed via UART_PS,
UART_MUL, and UART_DIV registers.
The UART clock is calculated as
UART clock = XTAL * UART_MUL / UART_DIV
The baudrate is calculated as
baud rate = UART clock / UART_PS / DLAB
Initialize fractional divider correctly for Intel Edison platform.
For backward compatibility we have to set initial DLAB value to 16
and speed to 115200 baud, where initial frequency is 29491200Hz, and
XTAL frequency is 38.4MHz.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
At present there are only 8-bit and 32-bit read/write routines in
the rtc uclass driver. This adds the 16-bit support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Various commands to NAND flash results in the NAND flash becoming busy.
For those commands the SoC should wait until the NAND indicates it is
no longer busy before sending further commands. However, there is a delay
between the time the SoC sends its last command and when the NAND flash
sets its Ready/Busy Pin. This delay (tWB) must be respected or the SoC may
falsely assume the flash is ready when in reality it just hasn't had enough
time to indicate that it is busy.
Properly delaying by tWB is already done for nand_command/nand_command_lp
in nand_base.c including the version of it in the Linux kernel. Therefore,
this patch brings the handling of tWB delay inline to nand_base.c
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
[trini: Reformat comments slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
The OMAP WDT IP block requires to be stopped before any write to its
registers is performed.
This problem has been thoroughly described in Linux kernel:
"watchdog: omap: assert the counter being stopped before reprogramming:
SHA1: 530c11d432727c697629ad5f9d00ee8e2864d453
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
The SPL image needs to be built with a different ECC configuration than the
U-Boot binary.
Add Kconfig options with defaults to provide a value that should work for
anyone, but is still configurable if needs be.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Scott Wood <oss@buserror.net>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The default U-Boot offset for the Allwinner SoCs was set to 32kB.
This was probably to try to maintain some compatibility with the current
image that we build for the MMC where the U-Boot binary is also located at
a 32kB offset.
However, this causes a number of issues. The first one is that it prevents
us from using a backup SPL entirely, which is troublesome in case where the
first would be corrupt (especially on MLC which have a higher number of
bitflips).
We also cannot use the original MMC image on the NAND, because we need to
prepare the SPL image to include the ECCs and randomizer settings, which
reduces the interest of setting it at that particular offset.
It also prevents us from upgrading and flashing the U-Boot and SPLs
independantly, since it's very likely that it will fall in the same erase
block.
Since that default wasn't used by any board, change it for 8MB, which will
be in an erase block of its own, all the erase blocks being multiple of
two. The highest erase block size we encountered is 4MB, which means that
in this particular setup, the first and second erase blocks will be for the
SPL and its backup, and the third for U-Boot.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
We'll need that symbol so that the default offset are defined
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Expose the RBTREE feature through Kconfig and select this option from the
MTD_UBI option.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jagan Teki <jagan@openedev.com>
[Rebased on master]
Signed-off-by: Jagan Teki <jagan@openedev.com>
When trying to autodetect the ECC and randomization configurations, the
driver starts with a randomization disabled and no seeds.
In this case, the number of seeds is obviously 0, and the randomize boolean
is set to false.
However, the logic that retrieves the seed for a given page offset will
blindly use the number of seeds, without testing if the randomization is
enabled, basically doing a modulo by 0.
As it turns out, the libgcc in the common toolchain returns 0 here, which
was our expected value in such a case, and why we would not detect it.
However, U-Boot's libgcc will for some reason return from the function
instead, resulting in an error to load the U-Boot binary in the SPL.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Scott Wood <oss@buserror.net>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This ports the support for configuring a GPIO for resetting the
Ethernet PHY (incl. such details as the reset polarity and
pulse-length) from the Designware driver.
X-AffectedPlatforms: A64-uQ7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
With d53ecad92f some unused interrupt related code was removed.
However all of these options are currently unused. Rather than migrate
some of these options to Kconfig we just remove the code in question.
The only related code changes here are that in some cases we use
CONFIG_STACKSIZE in non-IRQ related context. In these cases we rename
and move the value local to the code in question.
Fixes: d53ecad92f ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi")
Signed-off-by: Tom Rini <trini@konsulko.com>
Add separate enable/disable controls for driver-model serial. While this
is generally enabled in SPL it may not be in TPL, since serial output can
be obtained with the debug UART with minimal code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since TPL often needs to be very very small it may not make sense to
enable driver model. Add an option for this.
This changes brings the 'rock' board under the TPL limit with gcc 4.9.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we cannot use this function as an init sequence call without a
wrapper, since it returns the RAM size. Adjust it to set the RAM size in
global_data instead, and return 0 on success.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The Allwinner H5 is very close to the H3 SoC, but has ARMv8 cores.
To allow sharing the clocks, GPIO and driver code easily, create an
architecture agnostic MACH_SUNXI_H3_H5 Kconfig symbol.
Rename the existing symbol to MACH_SUNXI_H3_H5 where code is shared and
let it be selected by a new shared Kconfig option.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Addresses passed on to readl and writel are expected to be of the same
size as a pointer. Change the parameter types of sunxi_spi0_read_data()
to make the compiler happy and allow a warning-free aarch64 compile.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The new function dm_remove_devices_flags() is intented for driver specific
last-stage cleanup operations before the OS is started. This patch adds
this functionality and hooks it into the common device_remove()
function.
Drivers wanting to use this feature for some last-stage removal calls,
need to add one of the DM_REMOVE_xx flags to their driver .flags.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds the flags parameter to device_remove() and changes all
calls to this function to provide the default value of DM_REMOVE_NORMAL
for "normal" device removal.
This is in preparation for the driver specific pre-OS (e.g. DMA
cancelling) remove support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
The clock driver for the RK3399 mistakenly used (24 * 2^20) where it
should have used (24 * 10^6) in a few calculations.
This commits fixes this.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
The GMAC in the RK3399 is very similar to the RK3288 variant (i.e. it
is a Designware GMAC core and requires similar configuration as the
RK3288 to switch it to RGMII and set up the TX/RX delays for Gigabit).
The key difference is that the register offsets (within the GRF block)
and bit-offsets (within those registers) used to hold the configuration
differ between the various RK32/33 CPUs.
This change refactors the gmac_rockchip.c driver to use a function
table (selected via driver_data) to factor out these differences. Each
function's implementation then matches the underlying processor.
Some collateral changes are needed in the definitions describing the
bits and offsets in the GRF are needed to prefix each set of symbolic
constants with the SoC name to avoid name clashes... and in doing so,
the shifts for masks and constants have been moved into the header
files for readability (and to make it easier to stay below 80 chars).
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixed commit message typo s/factor our/factor out/:
Signed-off-by: Simon Glass <sjg@chromium.org>
The Ethernet driver for the RK3288/3399 GMAC makes sure that the clock
is ungated through a call to clk_set_rate(...). Even though nothing
needs to be done on the RK3399 (the clock gates are open and the clock
is external), we need to implement enough support to at least return
success to enable driver probing.
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Due to differences in the code paths for SPL and non-SPL, some static
constant structures remain unused in each build variant. This raises
warnings with recent GCC versions (we currently use GCC-6.3).
The warnings addressed in this commit (by matching #if conditions for
the variable definition with their uses) are:
* for the SPL build:
drivers/clk/rockchip/clk_rk3399.c:53:29: warning: 'cpll_init_cfg' defined but not used [-Wunused-const-variable=]
static const struct pll_div cpll_init_cfg = PLL_DIVISORS(CPLL_HZ, 1, 2, 2);
^~~~~~~~~~~~~
drivers/clk/rockchip/clk_rk3399.c:52:29: warning: 'gpll_init_cfg' defined but not used [-Wunused-const-variable=]
static const struct pll_div gpll_init_cfg = PLL_DIVISORS(GPLL_HZ, 2, 2, 1);
^~~~~~~~~~~~~
* for the non-SPL build:
drivers/clk/rockchip/clk_rk3399.c:54:29: warning: 'ppll_init_cfg' defined but not used [-Wunused-const-variable=]
static const struct pll_div ppll_init_cfg = PLL_DIVISORS(PPLL_HZ, 2, 2, 1);
^~~~~~~~~~~~~
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
To add GMAC (Gigabit Ethernet) support (limited to RGMII only at this
point), we need support for additional pin-configuration. This commit
adds the pinctrl support for GMAC in RGMII signalling mode:
* adds a PERIPH_ID_GMAC and the mapping from IRQ number to PERIPH_ID
* adds the required defines (in the GRF support) for configuring the
GPIOC pins for RGMII
* configures the RGMII pins (in GPIOC) when requested via pinctrl
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Designware HDMI controller and phy are used in other SoCs as well. Split
out platform independent code.
DW HDMI has 8 bit registers but they can be represented as 32 bit
registers as well. Add support to select access mode.
EDID reading code use reading by blocks which is not supported by other
SoCs in general. Make it more general using byte by byte approach, which
is also used in Linux driver.
Finally, not all DW HDMI controllers are accompanied with DW HDMI phy.
Support custom phys by making controller code independent from phy code.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Nickey Yang <nickey.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Cortex-A9 socs rk3066 and rk3188 share the IP but have their own
compatible values, so add them to make the i2c on these platforms accessible.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
The armclk starts in slow mode (24MHz) on the rk3188, which makes the whole
startup take a lot of time. We therefore want to at least move to the safe
600MHz value we can use with default pmic settings.
This is also the freqency the proprietary sdram-init leaves the cpu at.
For boards that have pmic control later in u-boot, we also add the option
to set the maximum frequency of 1.6GHz, if they so desire.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
The config options for pinctrl on the RK3188, RK3288, RK3328 and
RK3399 previously showed up in menuconfig with the generic string
descriptor "Rockchip pin control driver" requiring one to look through
the help/full description to identify which chip each menu entry was
for.
This change renames each option with the chip-name in the description
string to make it easy to identify the configuration options in
menuconfig.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This includes Marvell mvpp2 patches with the ethernet support for the
ARMv8 Armada 7k/8k platforms. The ethernet patches are all acked by Joe
and he is okay with me pushing them via the Marvell tree.
Introduce CONFIG_TEGRA124_MMC_DISABLE_EXT_LOOPBACK to disable the external clock
loopback and use the internal one on SDMMC3 as per the SDMMC_VENDOR_MISC_CNTRL_0
register's SDMMC_SPARE1 bits being set to 0xfffd according to the TRM.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is a preparation work for the support of CONFIG_BLK.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For consistency, use an accessor to access the private data. Also for the
same reason, rename all priv_data to priv.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
As pointed out by Stefan Chulski, this variable is unused and should be
removed.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On PPv2.2 we enable PHY polling, so we also need to configure the PHY
address in the specific PHY address rgisters.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Testing shows, that PHY polling needs to be enabled on Armada 7k/8k.
Otherwise ethernet transfers will not work correctly. PHY polling
is enabled per default after reset, so we do not need to specifically
enable it, but this makes it clearer.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add a missing occurrance of PHY_INTERFACE_MODE_RGMII_ID, which should
be handled identical to PHY_INTERFACE_MODE_RGMII.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds the GoP (Group of Ports) and NetC (Net Complex) setup to
the Marvell mvpp2 ethernet driver for the missing port 0. This code is
mostly copied from the Marvell U-Boot version and was written by Stefan
Chulski. Please note that only SFI support have been added, as this
is the only interface that this code has been tested with. XAUI and
RXAUI support might follow at a later stage.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds the GoP (Group of Ports) and NetC (Net Complex) setup to
the Marvell mvpp2 ethernet driver. This code is mostly copied from the
Marvell U-Boot version and was written by Stefan Chulski. Please
note that only RGMII and SGMII support have been added, as these are
the only interfaces that this code has been tested with.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Read the "phy-speed" DT property to differentiate between 1 and 2.5GB
SGMII operations. Please note that its unclear right now, if this
DT property will be accepted in mainline Linux. If not, we need to
revisit this code and change it to use the accepted property.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch does a bit of restructuring of the probe / init functions,
mainly to allow earlier register access as it is needed for the upcoming
GoP (Group of Ports) and NetC (Net Complex) code.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds the PPv2.2 specific FIFO configuration to the mvpp2
driver. The RX FIFO packet data size is changed to the recommended
FIFO sizes. The TX FIFO configuration is newly added.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Currently, the naming of the ethernet ports is not handled correctly in
the multi-CP (Communication Processor) case. On Armada 8k, the slave-CP
also instantiates an ethernet controller with the same device ID's.
This patch now takes this into account and adds the required base-id
so that the slave-CP ethernet devices will be named "mvpp2-3 ...".
This patch also updates my Copyright notice to include 2017 as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Since Armada 7K/8K is also equipped with a newer version of the MVPP2
ethernet controller, lets enable compilation of this driver for these
platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This fixes problems noticed with the PPv2.2 A7k/8k port, when not all
elements of the descriptors had been cleared before use.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch moves the base_probe function mvpp2_base_probe() from the
MISC driver to the ETH driver. When integrated in the MISC driver,
probe is called too early before the U-Boot ethernet infrastructure
(especially the MDIO / PHY interface) has been initialized. Resulting
in errors in mdio_register().
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In U-Boot the MDIO / SMI support is integrated in the mvpp2 driver,
currently only supporting the 32bit platforms (Armada 37x). This patch
now adds the A7k/8k PPv2.2 MDIO support to that the phy / mii IF
can be used as well on these platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Now that the mvpp2 driver has been modified to accommodate the support
for PPv2.2, we can finally advertise this support by adding the
appropriate compatible string.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In PPv2.1, we have a maximum of 8 RXQs per port, with a default of 4
RXQs per port, and we were assigning RXQs 0->3 to the first port, 4->7
to the second port, 8->11 to the third port, etc.
In PPv2.2, we have a maximum of 32 RXQs per port, and we must allocate
RXQs from the range of 32 RXQs available for each port. So port 0 must
use RXQs in the range 0->31, port 1 in the range 32->63, etc.
This commit adapts the mvpp2 to this difference between PPv2.1 and
PPv2.2:
- The constant definition MVPP2_MAX_RXQ is replaced by a new field
'max_port_rxqs' in 'struct mvpp2', which stores the maximum number of
RXQs per port. This field is initialized during ->probe() depending
on the IP version.
- MVPP2_RXQ_TOTAL_NUM is removed, and instead we calculate the total
number of RXQs by multiplying the number of ports by the maximum of
RXQs per port. This was anyway used in only one place.
- In mvpp2_port_probe(), the calculation of port->first_rxq is adjusted
to cope with the different allocation strategy between PPv2.1 and
PPv2.2. Due to this change, the 'next_first_rxq' argument of this
function is no longer needed and is removed.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adjusts how the MVPP2_ISR_RXQ_GROUP_REG register is
configured, since it changed between PPv2.1 and PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The PPv2.2 unit is connected to an AXI bus on Armada 7K/8K, so this
commit adds the necessary initialization of the AXI bridge.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit handles a few miscellaneous differences between PPv2.1 and
PPv2.2 in different areas, where code done for PPv2.1 doesn't apply for
PPv2.2 or needs to be adjusted (getting the MAC address, disabling PHY
polling, etc.).
Changed by Stefan for U-Boot:
Since mvpp2_port_power_up() has multiple callers in U-Boot, the U-Boot
version of this patch does not remove this function but simply adds the
check for MVPP21 before the mvpp2_port_fc_adv_enable() call.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adjusts the mvpp2 driver register mapping and access logic
to support PPv2.2, to handle a number of differences.
Due to how the registers are laid out in memory, the Device Tree binding
for the "reg" property is different:
- On PPv2.1, we had a first area for the common registers, and then one
area per port.
- On PPv2.2, we have a first area for the common registers, and a
second area for all the per-ports registers.
In addition, on PPv2.2, the area for the common registers is split into
so-called "address spaces" of 64 KB each. They allow to access the same
registers, but from different CPUs. Hence the introduction of cpu_base[]
in 'struct mvpp2', and the modification of the mvpp2_write() and
mvpp2_read() register accessors. For PPv2.1, the compatibility is
preserved by using an "address space" size of 0.
Changed by Stefan for U-Boot:
Since we don't support multiple CPUs in U-Boot, I've removed all the
code, macros and variables introduced in the Linux patch version for this.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In PPv2.2, the MVPP2_RXQ_DESC_ADDR_REG and MVPP2_TXQ_DESC_ADDR_REG
registers have a slightly different layout, because they need to contain
a 64-bit address for the RX and TX descriptor arrays. This commit
adjusts those functions accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit modifies the mvpp2_defaults_set() function to not do the
loopback and FIFO threshold initialization, which are not needed for
PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The MVPP2_RXQ_CONFIG_REG register has a slightly different layout
between PPv2.1 and PPv2.2, so this commit adapts the functions modifying
this register to accommodate for both the PPv2.1 and PPv2.2 cases.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adjusts the allocation and freeing of BM pools to support
PPv2.2. This involves:
- Checking that the number of buffer pointers is a multiple of 16, as
required by the hardware.
- Adjusting the size of the DMA coherent area allocated for buffer
pointers. Indeed, PPv2.2 needs space for 2 pointers of 64-bits per
buffer, as opposed to 2 pointers of 32-bits per buffer in
PPv2.1. The size in bytes is now stored in a new field of the
mvpp2_bm_pool structure.
- On PPv2.2, getting the physical and virtual address of each buffer
requires reading the MVPP2_BM_ADDR_HIGH_ALLOC to get the high order
bits of those addresses. A new utility function
mvpp2_bm_bufs_get_addrs() is introduced to handle this.
- On PPv2.2, releasing a buffer requires writing the high order 32 bits
of the physical address to MVPP2_BM_PHY_VIRT_HIGH_RLS_REG. We no
longer need to write the virtual address to MVPP2_BM_VIRT_RLS_REG.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adds the definition of the PPv2.2 HW descriptors, adjusts
the mvpp2_tx_desc and mvpp2_rx_desc structures accordingly, and adapts
the accessors to work on both PPv2.1 and PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Since the format of the HW descriptors is different between PPv2.1 and
PPv2.2, this commit introduces an intermediate union, with for now
only the PPv2.1 descriptors. The bulk of the driver code only
manipulates opaque mvpp2_tx_desc and mvpp2_rx_desc pointers, and the
descriptors can only be accessed and modified through the accessor
functions. A follow-up commit will add the descriptor definitions for
PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In preparation to the introduction for the support of PPv2.2 in the
mvpp2 driver, this commit adds a hw_version field to the struct
mvpp2, and uses the .data field of the DT match table to fill it in.
Having the MVPP21 and MVPP22 definitions available will allow to start
adding the necessary conditional code to support PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The PPv2.2 IP has a different TX and RX descriptor layout compared to
PPv2.1. In order to prepare for the introduction of PPv2.2 support in
mvpp2, this commit adds accessors for the different fields of the TX
and RX descriptors, and changes the code to use them.
For now, the mvpp2_port argument passed to the accessors is not used,
but it will be used in follow-up to update the descriptor according to
the version of the IP being used.
Apart from the mechanical changes to use the newly introduced
accessors, a few other changes, needed to use the accessors, are made:
- The mvpp2_txq_inc_put() function now takes a mvpp2_port as first
argument, as it is needed to use the accessors.
- Similarly, the mvpp2_bm_cookie_build() gains a mvpp2_port first
argument, for the same reason.
- In mvpp2_rx_error(), instead of accessing the RX descriptor in each
case of the switch, we introduce a local variable to store the
packet size.
- Similarly, in mvpp2_buff_hdr_rx(), we introduce a local "cookie"
variable to store the RX descriptor cookie, rather than accessing
it from the descriptor each time.
- In mvpp2_tx_frag_process() and mvpp2_tx() instead of accessing the
packet size from the TX descriptor, we use the actual value
available in the function, which is used to set the TX descriptor
packet size a few lines before.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As indicated by Russell King, the mvpp2 driver currently uses a lot
"phys" or "phys_addr" to store what really is a DMA address. This commit
clarifies this by using "dma" or "dma_addr" where appropriate.
This is especially important as we are going to introduce more changes
where the distinction between physical address and DMA address will be
key.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some more U-Boot specific 64bit support changes, mostly changing u32
to unsigned long.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The mvpp2 is going to be extended to support the Marvell Armada 7K/8K
platform, which is ARM64. As a preparation to this work, this commit
enables building the mvpp2 driver on ARM64, by:
- Adjusting the Kconfig dependency
- Fixing the types used in the driver so that they are 32/64-bits
compliant. We use dma_addr_t for DMA addresses, and unsigned long
for virtual addresses.
It is worth mentioning that after this commit, the driver is for now
still only used on 32-bits platforms, and will only work on 32-bits
platforms.
Changed by Stefan for U-Boot:
Removed the Kconfig change as it does not apply to U-Boot this way.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some of the MVPP2_PRS_RI_* definitions use the ~(value) syntax, which
doesn't compile nicely on 64-bit. Moreover, those definitions are in
fact unneeded, since they are always used in combination with a bit
mask that ensures only the appropriate bits are modified.
Therefore, such definitions should just be set to 0x0. In addition, as
suggested by Russell King, we change the _MASK definitions to also use
the BIT() macro so that it is clear they are related to the values
defined afterwards.
For example:
#define MVPP2_PRS_RI_L2_CAST_MASK 0x600
#define MVPP2_PRS_RI_L2_UCAST ~(BIT(9) | BIT(10))
#define MVPP2_PRS_RI_L2_MCAST BIT(9)
#define MVPP2_PRS_RI_L2_BCAST BIT(10)
becomes
#define MVPP2_PRS_RI_L2_CAST_MASK (BIT(9) | BIT(10))
#define MVPP2_PRS_RI_L2_UCAST 0x0
#define MVPP2_PRS_RI_L2_MCAST BIT(9)
#define MVPP2_PRS_RI_L2_BCAST BIT(10)
Because the values (MVPP2_PRS_RI_L2_UCAST, MVPP2_PRS_RI_L2_MCAST and
MVPP2_PRS_RI_L2_BCAST) are always applied with
MVPP2_PRS_RI_L2_CAST_MASK, and therefore there is no need for
MVPP2_PRS_RI_L2_UCAST to be defined as ~(BIT(9) | BIT(10)).
It fixes the following warnings when building the driver on a 64-bit
platform (which is not possible as of this commit, but will be enabled
in a follow-up commit):
drivers/net/ethernet/marvell/mvpp2.c: In function ‘mvpp2_prs_mac_promisc_set’:
drivers/net/ethernet/marvell/mvpp2.c:524:33: warning: large integer implicitly truncated to unsigned type [-Woverflow]
#define MVPP2_PRS_RI_L2_UCAST ~(BIT(9) | BIT(10))
^
drivers/net/ethernet/marvell/mvpp2.c:1459:33: note: in expansion of macro ‘MVPP2_PRS_RI_L2_UCAST’
mvpp2_prs_sram_ri_update(&pe, MVPP2_PRS_RI_L2_UCAST,
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The mvpp2_bm_bufs_add() currently creates a fake cookie by calling
mvpp2_bm_cookie_pool_set(), just to be able to call
mvpp2_pool_refill(). But all what mvpp2_pool_refill() does is extract
the pool ID from the cookie, and call mvpp2_bm_pool_put() with this ID.
Instead of doing this convoluted thing, just call mvpp2_bm_pool_put()
directly, since we have the BM pool ID.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
check_cache_range() warns that the top boundaries are not properly
aligned when flushing or invalidating the buffers and make these
operations fail.
This gets rid of the warnings:
CACHE: Misaligned operation at range ...
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit introduces timer driver for ARC.
ARC timers are configured via ARC AUX registers so we use special
functions to access timer control registers.
This driver allows utilization of either timer0 or timer1
depending on which one is available in real hardware. Essentially
only existing timers should be mentioned in board's Device Tree
description.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for fixed link to NETA driver.
This feature requreed for proper support of SFP modules
and onboard connected devices like Ethernet switches
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Terry Zhou <bjzhou@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add ability to use board-specific initialization flow
to NETA driver (for instance Ethernet switch bring-up)
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The USB device should linked to VBUS regulator through "vbus-supply"
DTS property.
This patch adds handling for "vbus-supply" property inside the USB
device entry for turning on the VBUS regulator upon the host adapter probe.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for "marvell,reset-gpio" property to mvebu DW PCIe
driver.
This option is valid when CONFIG_DM_GPIO=y
Change-Id: Ic17c500449050c2fbb700731f1a9ca8b83298986
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
We used to get the address of the optionnal ctrl_mod_mmap register as the
third memory range of the "reg" property. the linux driver moved to use a
syscon instead. In order to keep the DTS as close as possible to that of
linux, we move to using a syscon as well.
If SYSCON is not supported, the driver reverts to the old way of getting
the address from the 3rd memory range
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
In the DTS, the addresses are defined relative to the parent bus. We need
to translate them to get the address as seen by the CPU core.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
commit 2f11cd9121 ("dm: core: Handle global_data moving in SPL")
handles relocation of GD in SPL if spl_init() is called before
board_init_r(). So, uclass_root.next need not be initialized always
and accessing uclass_root.next->prev gives an abort. Update the
uclass_root only if it is available.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The Xenon SDHCI driver just missed the integration of this patch:
git ID 6d0e34bf
mmc: sdhci: Distinguish between base clock and maximum peripheral frequency
With this patch applied, the SDHCI subsystem complains now with this warning
while probing:
sdhci_setup_cfg: Hardware doesn't specify base clock frequency
This patch fixes this issue, by providing the missing host->max_clk
variable to the SDHCI subsystem.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Hu Ziji <huziji@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
It's redundant to send cmd13 after cmd9 whose response is not R1b. The
card devices will not be busy w/ cmd9.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
This patch adds Intel Tangier eMMC/SDHCI driver.
Intel Tangier SoC contains a hybrid of PCI and non-PCI devices. SDHCI
controller is one of the devices which are *not* on a PCI and, hence,
cannot be enumerated by standard PCI means. This driver, allows for
SDHCI controller on Tangier SoC to work in U-Boot.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We don't want pci_mmc to compile every time x86 compiles, only when
there's a platform that needs it. For that reason, we're adding a new
CONFIG_MMC_PCI which platforms can choose to enable.
Suggested-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This patch fixup iommu-map property on pci node to have a valid
mapping of requester-id to stream-id. The requester-id to stream-id
mapping is based on PCI-LUT table initialization.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Layerscape Chasis-2 also uses same PCIe controller as Chasis-3
and have similar PCI-Lut.
Signed-off-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add nand_size() function to move the nand size print into initr_nand().
Remove nand size print from nand_init() to allow other function to call
nand_init() without printing nand size.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add initialization flag to avoid initializing NAND Flash multiple
times, otherwise it will calculate a wrong total size.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2088A and its variants have different PCIe node than LS2080A.
The compatible string is updated accordingly.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The LS2088A series SoCs has different physical memory map address and
CCSR registers address against LS2080A series SoCs.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
SOC’s like LS1012A has only one chip select signal for QSPI flash.
Avoid scanning other flash.
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
MAC number used per QSGMII is not fixed. It may wary from SoC to SoC.
So move QSGMII wriop_init_dpmac() to SoC file.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In EP mode, to enable accesses from the Root Complex, the
CONFIG_READY bit must be set, otherwise any config attempts
from the Root Complex will be returned with config retry
status (CRS).
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch allows using i2c commands (e.g. "i2c probe", "i2c md", etc)
without the need to first select the bus number with e.g. "i2c dev 0".
This is the "i2c" command behavior similar to the one from pre DM, where
by default bus 0 was immediately accessible.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch updates the way in which psc, sscl and ssch I2C parameters are
calculated to be in sync with v4.9 Linux kernel
SHA1: 69973b830859bc6529a7a0468ba0d80ee5117826
in the ./drivers/i2c/busses/i2c-omap.c
The previous method was causing several issues:
- The internal I2C frequency (after prescaler) was far above recommended
one (7 - 12 MHz [*]) - the current approach brings better noise suppression
(as stated in Linux commit: SHA1: 84bf2c868f3ca996e5bb)
- The values calculated (psc, sscl and ssch) were far from optimal, which
caused on the test platform (AM57xx) the I2C0 SCL signal low time (Fast
Mode) of ~1.0us (the standard requires > 1.3 us).
[*] for AM57xx TRM SPRUHZ6G, Table 24,7
"HS I2C Register Values for Maximum I2C Bit Rates in I2C F/S, I2C HS Modes"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
v4.9 Linux release:
SHA1: 69973b830859bc6529a7a0468ba0d80ee5117826
in the ./drivers/i2c/busses/i2c-omap.c
recommends to use SCLH=5 and SCLL=7 values.
This patch sets them to default.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Normally, this would probably be done by adding devicetree aliases
to the main dtsi file for the lpc32xx and using bus->req_seq instead.
Since we want to have consistent i2c numbering, we cannot force the
bus->req_seq because. If for instance we have 3 buses numbered
from 0 to 2 with i2c0 enabled, i2c1 disabled and i2c2 enabled;
i2c2 can be selected using 'i2c dev 1' and 'i2c dev 2' commands
because a bus can be probed using req_seq or seq interchangeably.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Since the lpc32xx i2c driver does not yet support the devicetree bindings,
this structure is also needed by the board file as the hardware description
is done there.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
This is part of the prep work for the migration to the driver model.
It will enable the driver to support DM and non-DM configurations
using the same functions.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
This is part of the prep work for the migration to the driver model.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
This is part of the prep work for the migration to the driver model.
What used to be the probe function is now called probe_chip.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
This patch adds a reset controller implementation for STMicroelectronics
STi family SoCs; it allows a group of related reset like controls found
in multiple system configuration registers to be represented by a single
controller device.
Driver code has been mainly extracted from kernel
drivers/reset/sti/reset-stih407.c
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In the description of function pci_match_one_id(), there are some
problems on arguments list and return value description, so correct
them.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is sometimes convenient to know how many and/or which resources are
currently loaded into a TPG, e.g. to test is a flush operation succeeded.
Hence, we add a command that lists the resources of a given type currently
loaded into the TPM.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
If we want to load a key into a TPM, we need to know the designated parent
key's handle, so that the TPM is able to insert the key at the correct place in
the key hierarchy.
However, if we want to load a key whose designated parent key we also
previously loaded ourselves, we first need to memorize this parent key's handle
(since the handles for the key are chosen at random when they are inserted into
the TPM). If we are, however, unable to do so, for example if the parent key is
loaded into the TPM during production, and its child key during the actual
boot, we must find a different mechanism to identify the parent key.
To solve this problem, we add a function that allows U-Boot to load a key into
the TPM using their designated parent key's SHA1 hash, and the corresponding
auth data.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds support for having a "fixed-link" to some other MAC
(like some embedded switch-device).
For this purpose we introduce a new phy-driver, called "Fixed PHY".
Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is
described with a subnode below ethernet interface.
Most ethernet drivers (unfortunately not all are following same scheme
for searching/attaching phys) are calling "phy_connect(...)" for getting
a phy-device.
At this point we link in, we search here for a subnode called "fixed-
link", once found we start phy_device_create(...) with the special phy-
id PHY_FIXED_ID (0xa5a55a5a).
During init the "Fixed PHY" driver has registered with this id and now
gets probed, during probe we get all the details about fixed-link out of
dts, later on the phy reports this values.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Fixed cache misaligned issue in the net driver. The issue shows-up when
a call to flush_dcache_range is made with unaligned memory. The memory
must be aligned to ARCH_DMA_MINALIGN.
Signed-off-by: Suji Velupillai <suji.velupillai@broadcom.com>
Tested-by: Suji Velupillai <suji.velupillai@broadcom.com>
Reviewed-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: JD Zheng <jiandong.zheng@broadcom.com>
Reviewed-by: Shamez Kurji <shamez.kurji@broadcom.com>
Signed-off-by: Steve Rae <steve.rae@raedomain.com>
Cover Letter:
This series resolves issues specific to the Broadcom SF2 driver:
- fix cache misaligned issue
- convert to Kconfig
END
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Currently the mac address is programmed directly in _sunxi_emac_eth_init
making it a one time inflexible operation. By moving it into a separate
function, we can now use this more flexibly.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This replaces legacy arch/arc/lib/timer.c implementation and allows us
to describe ARC Timers in Device Tree. Among other things that way we
may properly inherit Timer's clock from CPU's clock s they really run
synchronously.
This commit introduces timer driver for ARC.
ARC timers are configured via ARC AUX registers so we use special
functions to access timer control registers.
This driver allows utilization of either timer0 or timer1
depending on which one is available in real hardware. Essentially
only existing timers should be mentioned in board's Device Tree
description.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for fixed link to NETA driver.
This feature requreed for proper support of SFP modules
and onboard connected devices like Ethernet switches
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Terry Zhou <bjzhou@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add ability to use board-specific initialization flow
to NETA driver (for instance Ethernet switch bring-up)
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The USB device should linked to VBUS regulator through "vbus-supply"
DTS property.
This patch adds handling for "vbus-supply" property inside the USB
device entry for turning on the VBUS regulator upon the host adapter probe.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for "marvell,reset-gpio" property to mvebu DW PCIe
driver.
This option is valid when CONFIG_DM_GPIO=y
Change-Id: Ic17c500449050c2fbb700731f1a9ca8b83298986
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
We used to get the address of the optionnal ctrl_mod_mmap register as the
third memory range of the "reg" property. the linux driver moved to use a
syscon instead. In order to keep the DTS as close as possible to that of
linux, we move to using a syscon as well.
If SYSCON is not supported, the driver reverts to the old way of getting
the address from the 3rd memory range
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
In the DTS, the addresses are defined relative to the parent bus. We need
to translate them to get the address as seen by the CPU core.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
commit 2f11cd9121 ("dm: core: Handle global_data moving in SPL")
handles relocation of GD in SPL if spl_init() is called before
board_init_r(). So, uclass_root.next need not be initialized always
and accessing uclass_root.next->prev gives an abort. Update the
uclass_root only if it is available.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The Xenon SDHCI driver just missed the integration of this patch:
git ID 6d0e34bf
mmc: sdhci: Distinguish between base clock and maximum peripheral frequency
With this patch applied, the SDHCI subsystem complains now with this warning
while probing:
sdhci_setup_cfg: Hardware doesn't specify base clock frequency
This patch fixes this issue, by providing the missing host->max_clk
variable to the SDHCI subsystem.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Hu Ziji <huziji@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
It's redundant to send cmd13 after cmd9 whose response is not R1b. The
card devices will not be busy w/ cmd9.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
This patch adds Intel Tangier eMMC/SDHCI driver.
Intel Tangier SoC contains a hybrid of PCI and non-PCI devices. SDHCI
controller is one of the devices which are *not* on a PCI and, hence,
cannot be enumerated by standard PCI means. This driver, allows for
SDHCI controller on Tangier SoC to work in U-Boot.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We don't want pci_mmc to compile every time x86 compiles, only when
there's a platform that needs it. For that reason, we're adding a new
CONFIG_MMC_PCI which platforms can choose to enable.
Suggested-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Move this in to Kconfig with a default of 115200.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Run moveconfig.py, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
This includes support for rk3188 from Heiko Stübner and and rk3328 from
Kever Yang. Also included is SPL support for rk3399 and a fix for
rk3288 to get it booting again (spl_early_init()).
This driver uses the same pin control binding as that of linux, binding
document of this patch is copied from linux. One addition done is for
GPIO input and output mode configuration which was missing.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Before clock driver availability it was required to enable usart1 clock
for serial init but now with clock driver is taking care of usart1 clock.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
add basic clock driver support for stm32f7 to enable clocks required by
the peripherals.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds device tree support for stm32f7 serial driver & removes serial
platform data structure.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add compatible property for i.MX7ULP.
Add a weak init_usdhc_clk function, i.MX7ULP use this to init the clock.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Add i.MX7ULP support.
The buadrate calculation on i.MX7ULP is different,so add a new setbrg
function for i.MX7ULP.
Add a enum lpuart_devtype for runtime check for different platforms.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Shaohui Xie <Shaohui.Xie@nxp.com>
Cc: Alison Wang <b18965@freescale.com>
Drop CONFIG_LPUART_32B_REG.
Move the register structure to a common file include/fsl_lpuart.h
Define lpuart_serial_platdata structure which includes the reg base and flags.
For 32Bit register access, use lpuart_read32/lpuart_write32 which handles
big/little endian.
For 8Bit register access, still use the orignal code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Shaohui Xie <Shaohui.Xie@nxp.com>
Cc: Alison Wang <b18965@freescale.com>
Add lpi2c driver for i.MX7ULP.
Need to enable the two options to use this driver:
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_IMX_LPI2C=y
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add i.MX7ULP pinctrl driver.
Select CONFIG_PINCTRL_IMX7ULP to use this driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by : Stefano Babic <sbabic@denx.de>
This driver implements the HW WATCHDOG functions. Which needs
to set CONFIG_HW_WATCHDOG to use them. This is disabled by default for
mx7ulp.
Use watchdog for reset cpu. Implement this in the driver.
Need to define CONFIG_ULP_WATCHDOG to build it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Update the mxc_ocotp driver to support i.MX7ULP.
The read/write sequence has some changes due to
PDN and OUT_STATUS registers added and TIME register is
removed. Also update the bank size and number.
Add is_mx7ulp macro in sys_proto.h
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Add the imx_rgpio2p driver for Rapid GPIO2P controllers on i.MX7ULP.
Have added all ports on RGPIO2P_0 and RGPIO2P_1.
The configurations CONFIG_IMX_RGPIO2P and CONFIG_DM_GPIO must be set
to y to enable the drivers.
To use the GPIO function, the IBE and OBE needs to set in IOMUXC.
We did not set the bits in driver, but leave them to IOMUXC settings
of the GPIO pins. User should use IMX_GPIO_NR to generate the GPIO number
for gpio APIs access.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Despite the comment in the code, CSC unit is never used. According to
the only public description of DW HDMI controller (i.MX6 manual), CSC
unit is bypassed in MC_FLOWCTRL register and then actually powered
down in MC_CLKDIS register.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Function hdmi_lookup_n_cts() is feed with clock in Hz, which gets
compared with clocks in kHz. Fix that by converting all clocks to Hz.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Documentation says that we're returning true/false, not 1/0 so adapt
the function to return actual booleans.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Add rk3328 pinctrl driver and grf/iomux structure definition.
Signed-off-by: William Zhang <william.zhang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a driver for setting up and modifying the various PLLs and peripheral
clocks on the RK3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Driver for the sysreset of Rockchip rk3188 socs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Add a driver which supports pin multiplexing setup for the most commonly
used peripherals.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Add necessary structs to have the driver also work for the serial
on the rk3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
The gpll and cpll init values are only used in rk_clk_init in the SPL
and therefore produce compile time warnings in regular uboot builds.
Fix that with an #ifdef.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
Right now the u-boot,dm-pre-reloc flag will make each marked node
always appear in both spl and tpl. But systems needing an additional
tpl might have special constraints for each, like the spl needing to
be very tiny.
So introduce two additional flags to mark nodes for only spl or tpl
environments and introduce a function dm_fdt_pre_reloc to automate
the necessary checks in code instances checking for pre-relocation
flags.
The behaviour of the original flag stays untouched and still marks
a node for both spl and tpl.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Do not use the API which of-platdata not support.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
Change some API in order to enable of-platdata.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
rk3399 grf register bit defenitions should locate in header
file, so that not only pinctrl can use it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
- Move to DM clk driver
- Add clk support for zynq_sdhci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAljKWVcACgkQykllyylKDCEsgACfey0mgRaGVMLSxMMCGgJQIK70
/oYAn3raqYrJ2e2fsjb1B5WodYcDe8L5
=JYC5
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2017.05' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2017.05
- Move to DM clk driver
- Add clk support for zynq_sdhci
This device tree has been extracted from v4.9 kernel
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add SDHCI host controller found on STMicroelectronics SoCs
On some ST SoCs, i.e. STiH407/STiH410, the MMC devices can live
inside a dedicated flashSS sub-system that provides an extend subset
of registers that can be used to configure the Arasan MMC/SD Host
Controller.
This means, that the SDHCI Arasan Controller can be configured to be
eMMC4.5 or 4.3 spec compliant.
W/o these settings the SDHCI will configure and use the MMC/SD
controller with limited features e.g. PIO mode, no DMA, no HS etc.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This patch adds support to ASC (asynchronous serial controller)
driver, which is basically a standard serial driver. This IP
is common across other STMicroelectronics SoCs
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since the reserved RAM is tracked by gd->arch.resv_ram, calculation
of MC memory blocks can be simplified. The MC RAM is guaranteed to be
aligned by the reservation process.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
For ARMv8 Layerscape SoCs, secure memory and MC memorey are reserved
at the end of DDR. DDR is spit into two or three banks. This patch
reverts commit aabd7ddb and simplifies the calculation of reserved
memory, and moves the code into common SoC file. Secure memory is
carved out first. DDR bank size is reduced. Reserved memory is then
allocated on the top of available memory. U-Boot still has access
to reserved memory as data transferring is needed. Device tree is
fixed with reduced memory size to hide the reserved memory from OS.
The same region is reserved for efi_loader.
Signed-off-by: York Sun <york.sun@nxp.com>
The execution flow is currently like this for aldo_num == 1 or 2:
int axp_set_aldo(int aldo_num, unsigned int mvolt)
{
...
if (mvolt == 0)
return pmic_bus_clrbits(AXP809_OUTPUT_CTRL1,
AXP809_OUTPUT_CTRL1_ALDO1_EN << (aldo_num - 1));
...
return pmic_bus_clrbits(AXP809_OUTPUT_CTRL1,
AXP809_OUTPUT_CTRL1_ALDO1_EN << (aldo_num - 1));
}
I.e. aldo1 and aldo2 will always be disabled. This patch fixes it by
setting (rather than clearing) the enable bit when mvolt != 0.
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Fixes: 795857df41 ("sunxi: power: add AXP809 support")
"unsigned long" is a lousy data type when it comes to match peripheral
hardware registers with a fixed size.
Just do the obvious and match a 32-bit display format with an "u32"
data type for casting.
This fixes the logo display on 64-bit architectures, which produced
a black line on the right side of the logo with non-black backgrounds.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When the zynq_gem driver initializes the phy it sets the supported
features that the phy can support and advertise. However instead of
masking the supported features such that it limits the available
features it sets the phy to have the exact supported features of the
zynq_gem. This is problematic as it will enable features that a phy does
not have or cannot advertise.
Specifically this appears as an issue when using a phy that is only
capable of 10/100, but the zynq_gem driver will override this and try to
enable and advertise 10/100/1000.
Reported-by: Arno Steffens <star@gmx.li>
Fixes: 80243528ef ("net: gem: Fix gem driver on 1Gbps LAN")
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Tested-by: Arno Steffens <star@gmx.li>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
For the boards such as smartweb on which the clock driver isn't
supported, the ethernet fail to be found when booting up with
the below log.
---8<---
Net: No ethernet found.
--->8---
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
With this patch, USB Command Verifier is happy with our DFU
implementation on Chapter 9 tests.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of only copying if strlen(s) is less than 32 characters, let's
just copy at most 31 characters regardless of the size of
serial#. This will guarantee that we always have a serial number if
serial# environment variable is set to anything.
Note that without a proper serial number, USB Command Verifier fails
our test of Device Descriptor since we will claim to have a serial
number without really providing one when requested.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If last packet is short, we shouldn't write req->length bytes to
non-volatile media, we should write only what's available to us, which
is held in req->actual.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
harmonize result with other handle_XXX() functions: return int for size
remove the define RET_STAT_LEN : no more necessary
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
return the correct size for DFU_GETSTATE result (1 byte in DFU 1.1 spec)
to avoid issue in USB protocol and the variable "value" is propagated
to req->lenght as all the in the other request with answer
- DFU_GETSTATUS
- DFU_DNLOAD
- DFU_UPLOAD
Then the buffer is correctly treated in USB driver
NB: it was the only request witch directly change "req->actual"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
The "DFU descriptor set" must contain the "DFU functional descriptor"
but it is missing today in U-Boot code
(cf: DFU spec 1.1, chapter 4.2 DFU Mode Descriptor Set)
This patch only allocate buffer and copy DFU functional descriptor
after interfaces.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
Remove sys_proto.h inclusion which is not used by the driver.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>