Commit Graph

60853 Commits

Author SHA1 Message Date
Weijie Gao
e3b326fee5 dts: mtmips: add mmc related nodes for mt7628an.dtsi
This patch adds mmc related nodes for mt7628an.dtsi

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:44 +02:00
Weijie Gao
77ebea23c3 mmc: mtk-sd: add a dts property cd-active-high for builtin-cd mode
This patch adds a dts property cd-active-high for builtin-cd mode to make
it configurable instead of using hardcoded active-low.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:44 +02:00
Weijie Gao
3c92a957ee mmc: mtk-sd: add support for MediaTek MT7620/MT7628 SoCs
This patch adds mmc support for MediaTek MT7620/MT7628 SoCs.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:44 +02:00
Weijie Gao
cff0b044d2 dts: mtmips: enable eth port0 led and link poll functions for all boards
This patch adds default p0led status and phy0 link polling for all boards.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:44 +02:00
Weijie Gao
877d03903c net: mt7628-eth: add support to isolate LAN/WAN ports
This patch add support for mt7628-eth to isolate LAN/WAN ports mainly to
prevent LAN devices from getting IP address from WAN.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:44 +02:00
Weijie Gao
c88ee3ea0a net: mt7628-eth: free rx descriptor on receiving failure
When received a packet with an invalid length recorded in rx descriptor,
we should free this rx descriptor to allow us to continue to receive
following packets.
Without doing so, u-boot will stuck in a dead loop trying to process this
invalid rx descriptor.

This patch adds a call to mt7628_eth_free_pkt() after received an invalid
packet length.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:44 +02:00
Weijie Gao
f079321009 net: mt7628-eth: make phy link up detection optional via DT
The mt7628 has an embedded ethernet switch (5 phy ports + 1 cpu port).
Although in IOT mode only port0 is usable, the phy0 is still connected
to the switch, not the ethernet gmac directly.

This patch rewrites it and makes it optional. It can be turned on by adding
mediatek,poll-link-phy = <?> explicitly into the eth node. By default the
driver is switch mode with all 5 phy ports working without link detection.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:44 +02:00
Weijie Gao
2734fdef5c net: mt7628-eth: remove hardcoded gpio settings and regmap-based phy reset
This patch removes hardcoded gpio settings as they have been replaced by
pinctrl in dts, and also replaces regmap-based phy reset with a more
generic reset controller.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:44 +02:00
Weijie Gao
4cce51141f phy: mt76x8-usb-phy: add slew rate calibration and remove non-mt7628 part
This patch adds slew rate calibration for mt76x8-usb-phy, removes code
which belongs to mt7620, and gets rid of using syscon and regmap by using
clock driver and reset controller.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:44 +02:00
Weijie Gao
6658ebc96a dts: mtmips: update reset controller node for mt7628
This patch updates reset controller node for mt7628

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:44 +02:00
Weijie Gao
f7ae6b682c reset: add reset controller driver for MediaTek MIPS platform
This patch adds reset controller driver for MediaTek MIPS platform and
header file for mt7628.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:44 +02:00
Weijie Gao
123ffd4679 dts: mtmips: add default pinctrl for uart nodes
This patch adds default pinctrl for uart nodes

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:44 +02:00
Weijie Gao
fdf92df285 dts: mtmips: add pinctrl node for mt7628
This patch adds pinctrl node with default pin state for mt7628an.dtsi.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:44 +02:00
Weijie Gao
3fad441c54 pinctrl: add support for MediaTek MT7628
This patch adds pinctrl support for mt7628, with a file for common pinmux
functions and a file for mt7628 which has additional support for pinconf.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:44 +02:00
Weijie Gao
43405e009b spi: mt7621-spi: restore default register value after each xfer
Currently this driver uses a different way to implement the spi xfer,
by modifying some fields of two registers, which is incompatible with the
MTK's original SDK linux driver. This will cause the flash data being
damaged by the SDK driver.

This patch lets the mt7621_spi_set_cs() restore the original register
fields after cs deactivated.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:44 +02:00
Weijie Gao
54a6b8e793 spi: mt7621-spi: remove data cache and rewrite its xfer function
The mt7621 spi controller supports continuous generic half-duplex spi
transaction. There is no need to cache xfer data at all.

To achieve this goal, the OPADDR register must be used as the first data
to be sent. And follows the eight generic DIDO registers. But one thing
different between OPADDR and DIDO registers is OPADDR has a reversed byte
order.

With this patch, any amount of data can be read/written in a single xfer
function call.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:44 +02:00
Weijie Gao
f09978566b spi: mt7621-spi: use clock frequency from clk driver
This patch lets the spi driver to use clock provided by the clk driver
since the new clk-mt7628 driver provides accurate sys clock frequency.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:44 +02:00
Weijie Gao
2d767a7497 dts: mtmips: add clock node for mt7628
This patch adds clkctrl node for mt7628 and adds clocks property for
some node.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:44 +02:00
Weijie Gao
77ed3c42fe clk: add clock driver for MediaTek MT76x8 platform
This patch adds a clock driver for MediaTek MT7628/7688 SoC.
It provides clock gate control as well as getting clock frequency for
CPU/SYS/XTAL and some peripherals.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:44 +02:00
Weijie Gao
5fcea8d3f9 dts: mtmips: enable high-speed UART support for mt7628
All three UARTs of mt7628 are actually MediaTek's high-speed UARTs which
support baudrate up to 921600.
The high-speed UART is compatible with ns16550 when baudrate <= 115200.

Add compatible string to dtsi file so u-boot can use it when serial_mtk
driver is built in.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:44 +02:00
Weijie Gao
d1d8814458 dts: mtmips: move uart property clock-frequency into mt7628an.dtsi
The UART of MT7628 has fixed 40MHz input clock so there is no need to put
clock-frequency in every dts files. Just put it into the common dtsi file.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:44 +02:00
Weijie Gao
44fa676e58 serial: serial_mtk: add non-DM version for SPL
This patch adds non-DM version for mtk hsuart driver and makes it
compatible with ns16550a driver in configuration.
This is needed in SPL with CONFIG_SPL_DM disabled for reducing size.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:43 +02:00
Weijie Gao
99ced5331b serial: serial_mtk: enable FIFO and disable flow control
This patch adds codes to enable FIFO and disable flow control taken from
ns16550 driver.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:43 +02:00
William Zhang
e365de9051 drivers: nand: brcmnand: fix nand_chip ecc layout structure
The current brcmnand driver is based on 4.18 linux kernel which uses
mtd_set_ooblayout to set ecc layout. But nand base code in u-boot is from
old kernel which does not use this new API and expect nand_chip.ecc.layout
structure to be set. This cause nand_scan_tail function running into a bug
check if the device has a different oob size than the default ones.

This patch ports the brcmstb_choose_ecc_layout function from kernel 4.6.7
that supports the ecc layout struture and replaces the mtd_set_ooblayout
method

Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-10-25 17:20:43 +02:00
Álvaro Fernández Rojas
a69bae04fd mips: bmips: switch to board defines for dtb
Fixes commit 344db3f, which added missing bmips dtbs depending on their SoCs.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-10-25 17:20:43 +02:00
Álvaro Fernández Rojas
f923c758e0 bmips: correct name characters
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-10-25 17:20:43 +02:00
Álvaro Fernández Rojas
55daf1c45c bmips: configs: switch to size definitions
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-10-25 17:20:43 +02:00
Álvaro Fernández Rojas
9e484636f1 mips: bmips: remove unneeded definitions
These are no longer needed.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-10-25 17:20:43 +02:00
Álvaro Fernández Rojas
331bee8786 bmips: enable vr-3032u nand support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-10-25 17:20:43 +02:00
Álvaro Fernández Rojas
0f57c932f9 bmips: bcm63268: add support for brcmnand
BCM63268 uses 4.0 HW nand controller, which is currently supported by
brcmnand driver.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-10-25 17:20:43 +02:00
Álvaro Fernández Rojas
c4bf879063 bmips: bcm6362: add support for brcmnand
BCM6362 uses old 2.2 HW nand controller, which isn't currently supported by
brcmnand driver.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-10-25 17:20:43 +02:00
Álvaro Fernández Rojas
12dfa45947 bmips: bcm6328: add support for brcmnand
BCM6328 uses old 2.2 HW nand controller, which isn't currently supported by
brcmnand driver.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-10-25 17:20:43 +02:00
Álvaro Fernández Rojas
edbd175c66 bmips: bcm6368: add support for brcmnand
BCM6368 uses old 2.1 HW nand controller, which isn't currently supported by
brcmnand driver.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-10-25 17:20:43 +02:00
Álvaro Fernández Rojas
a9f80cf9ad nand: brcm: add BCM6368 support
This adds support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-10-25 17:20:43 +02:00
Ramon Fried
22247c63ac MIPS: add compile time definition of L2 cache size
If configuration is set to skip low level init, automatic
probe of L2 cache size is not performed and the size is set to 0.
Flushing or invalidating the L2 cache will fail in this case.

Add a static configuration (SYS_DCACHE_LINE_SIZE) with default set to 0.

Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
2019-10-25 17:20:43 +02:00
Tom Rini
17fd9915a4 Merge branch '2019-10-24-UFS-support'
- Add Universal Flash Storage (UFS) support
2019-10-24 09:51:48 -04:00
Tom Rini
c9e40996f9 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvell
- Add support for HyperBus Memory Controller of TI's J721e
  and AM654 SoCs (Vignesh)
2019-10-24 07:32:21 -04:00
Vignesh Raghavendra
a360e42216 configs: j721e_evm_a72_defconfig: Add HBMC related configs
Enable HBMC and HyperFlash in A72 SPL and A72 U-Boot

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2019-10-24 09:49:32 +02:00
Vignesh Raghavendra
1fc18e173e configs: j721e_evm.h: Define CONFIG_SYS_MAX_FLASH_BANKS_DETECT
Define CONFIG_SYS_MAX_FLASH_BANKS_DETECT so that number of flash banks
are automatically detected by CFI flash driver

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2019-10-24 09:49:27 +02:00
Vignesh Raghavendra
02e262c249 arm: dts: k3-j721e-som-p0: Add HyperFlash node
J721e SoM as a 64MB HyperFlash on board. Add pinmux and DT node for the
same.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2019-10-24 09:49:22 +02:00
Vignesh Raghavendra
358032f9a5 arm: dts: k3-j721e-mcu-wakeup: Add HyperBus Controller node
Add DT node for HyperBus Memory Controller in the FSS. On J721e, its not
possible to use OSPI0 and HBMC simultaneously as they are muxed within
the Flash Subsystem hence disable HBMC by default as keep OSPI enabled.
Bootloader will fixup DT when it detects HyperFlash instead of OSPI.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2019-10-24 09:49:16 +02:00
Vignesh Raghavendra
c2dfd0a4d8 mtd: Add TI HyperBus Memory Controller driver
AM654/J721e has HyperBus Memory Controller that supports HyperFlash and
HyperRAM devices. It provides a memory mapped interface to interact with
these devices. Add a driver to support the same.
Driver calibrates the controller, setups up for MMIO access and probes
HyperFlash child node.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2019-10-24 09:49:10 +02:00
Vignesh Raghavendra
d75eacf9b8 mtd: cfi_flash: Use CONFIG_SYS_MONITOR_BASE only when defined
Make use of CONFIG_SYS_MONITOR_BASE only when available to avoid build
error when CONFIG_SYS_MONITOR_BASE is not defined.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2019-10-24 09:48:53 +02:00
Faiz Abbas
c6ffc0d62f configs: j721e_evm_a72: Enable configs for UFS
Enable SCSI and UFS related configs.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-10-23 20:47:12 -04:00
Faiz Abbas
13b6770c05 env: ti: Add environment variables to boot from UFS
Add environment variables to boot kernel from a filesystem contained in
the 2nd UFS LUN. The user can boot from a ufs filesystem just by
entering the following commands.

=> setenv boot ufs
=> boot

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-10-23 20:47:12 -04:00
Faiz Abbas
a539c8bd7d cmd: Add Support for UFS commands
Add Support for commands to initialize and configure UFS devices.

TODO: Add Support for commands to resize and reconfigure LUNs
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-10-23 20:47:12 -04:00
Faiz Abbas
991e8a5ab8 arm: dts: k3-j721e-main: Add UFS nodes
Add TI UFS glue layer and Cadence UFS Host controller DT nodes.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-10-23 20:47:12 -04:00
Faiz Abbas
4390eaf676 ufs: Add glue layer driver for TI J721E devices
Add glue layer driver for the controller present on TI's J721E devices.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-10-23 20:47:12 -04:00
Faiz Abbas
ef5fb5a84c ufs: Add Support for Cadence platform UFS driver
Add Support for the platform driver for the Cadence device present on
TI's J721e device.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-10-23 20:47:12 -04:00
Faiz Abbas
7feafb0ae4 ufs: Add Initial Support for UFS subsystem
Add Support for UFS Host Controller Interface (UFSHCI) for communicating
with Universal Flash Storage (UFS) devices. The steps to initialize the
host controller interface are the following:

- Initiate the Host Controller Initialization process by writing to the
Host controller enable register.
- Configure the Host Controller base address registers by allocating a
host memory space and related data structures.
- Unipro link startup procedure
- Check for connected device
- Configure UFS host controller to process requests

Also register this host controller as a SCSI host controller.

Taken from Linux Kernel v5.2 (drivers/scsi/ufs/ufshcd.c) and ported to
U-boot.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-10-23 20:47:12 -04:00